IKEA RDWTI60 Manuel utilisateur

RENLIG

DWTI60

GB

DE

FR

IT

ENGLISH 4

DEUTSCH 24

FRANÇAIS 47

ITALIANO 76

Contents

Safety information 4

Product description 5

Control panel 6

Washing programmes 8

Use of the appliance 9

Setting the water softener 9

Use of dishwasher salt 10

Use of rinse aid 11

Loading cutlery and dishes 11

Use of detergent 13

Setting and starting a washing programme

14

Care and cleaning 15

What to do if… 16

Technical data 18

Installation 19

Water connection 19

Electrical connection 20

Environment concerns 20

IKEA GUARANTEE 21

Subject to change without notice

Safety information

For your safety and correct operation

of the appliance, read this manual

carefully before installation and use. Always

keep these instructions with the appliance

even if you move or sell it. Users must fully

know the operation and safety features of

the appliance.

Correct use

• The appliance is designed exclusively for

domestic use.

• Only use the appliance to clean house-

hold utensils that are applicable for dish-

washers.

• Do not put solvents in the appliance. Risk

of explosion.

• Put the knives and all items with sharp

points in the cutlery basket with their

points down. If not, put in a horizontal

position in the upper basket.

• Use only branded products for dishwash-

ers (detergent, salt, rinse aid).

• If you open the door while the appliance

is in operation, hot steam can escape.

Risk of skin burns.

• Do not remove dishes from the dishwash-

er before the end of the washing pro-

gramme.

• When the washing programme is com-

pleted, disconnect the mains plug from

the mains socket and close the water tap.

• Only an authorised service engineer can

repair this appliance. Use only original

spare parts.

• Do not do repairs yourself to prevent in-

jury and damage to the appliance. Al-

ways contact your local After Sales Serv-

ice.

General safety

• Persons (including children) with reduced

physical sensory, mental capabilities or

lack of experience and knowledge must

not use the appliance. They must have

supervision or instruction for the opera-

tion of the appliance by a person respon-

sible for their safety.

• Obey the safety instructions from the

manufacturer of the dishwasher deter-

gent to prevent burns to eyes, mouth and

throat.

• Do not drink the water from the dish-

washer. Detergent residues can stay in

your appliance.

• Always close the door when you do not

use the appliance to prevent injury and

not to stumble over the open door.

• Do not sit or stand on the open door.

Child safety

• Only adults can use this appliance. Chil-

dren must get supervision to make sure

that they do not play with the appliance.

• Keep all the packaging away from chil-

dren. There is a risk of suffocation.

ENGLISH 4

• Keep all detergents in a safe area. Do

not let children touch the detergents.

• Keep children away from the appliance

when the door is open.

Installation

• Make sure that the appliance is not dam-

aged because of transport. Do not con-

nect a damaged appliance. If necessary,

contact the supplier.

• Remove all packaging before first use.

• A qualified and competent person must

do the electrical installation.

• A qualified and competent person must

do the plumbing installation.

• Do not change the specifications or modi-

fy this product. Risk of injury and damage

to the appliance.

• Do not use the appliance:

– if the mains cable or water hoses are

damaged,

– if the control panel, worktop or plinth

area are damaged, that you can get

access to the inner side of the appli-

ance.

If you have any doubts, please contact

your After Sales Service. Refer to the list

of the After Sales Services at the end of

user manual.

• Do not drill into the sides of the appliance

to prevent damage to hydraulic and

electrical components.

Warning! Carefully obey the

instructions for electrical and water

connections.

Product description

1

2

3

4

5

6

7

8

9

1 Upper basket

2 Water hardness dial

3 Salt container

4 Detergent dispenser

5 Rinse aid dispenser

6 Rating plate

7 Filters

8 Lower spray arm

ENGLISH 5

9 Upper spray arm

Control panel

1 On/off button

2 Delay start button

3 Programme selection/cancel button / (SELECT/CANCEL)

4 Indicator lights

5 Programme indicator lights

Indicator lights

The indicator light comes on when the

washing programme is completed. Auxiliary

functions:

• Level of the water softener.

• Activation/deactivation the audible sig-

nals.

• An alarm if the appliance has a malfunc-

tion.

1)

The indicator light comes on when it is nec-

essary to fill the rinse aid. Refer to the chap-

ter 'Use of rinse aid'.

1)

The indicator light comes on when it is nec-

essary to fill the salt container. Refer to the

chapter 'Use of dishwasher salt'.

The salt indicator light can stay on for some

hours, but it does not have an unwanted ef-

fect on the operation of the appliance.

1) The indicator light is off while a washing programme operates.

Programme selection/cancel button

Use the programme selection/cancel button

for these operations:

• To set the washing programme. Refer to

the chapter 'Setting and starting a wash-

ing programme'.

ENGLISH 6

• To set the water softener. Refer to the

chapter 'Setting the water softener'.

• To deactivate/activate the audible sig-

nals. Refer to the section 'Audible signals'.

• To cancel a washing programme in pro-

gress. Refer to the chapter 'Setting and

starting a washing programme'.

Delay start button

Use the delay start button to delay the start

of the washing programme with an interval

of 3 hours. Refer to the chapter 'Setting and

starting a washing programme'.

Setting mode

The appliance is in setting mode when all

the programme indicator lights are off and

the end indicator light flashes.

The appliance must be in setting mode for

these operations:

– To set a washing programme.

– To set the water softener level.

– To deactivate/activate the audible sig-

nals.

If a programme indicator light is on, cancel

the programme to go back to the setting

mode. Refer to the chapter "Setting and

starting a washing programme".

Programme indicator lights A and B

Apart the selection of the corresponding

washing programme, these lights have an

auxiliary functions:

• The adjustment of the water softener lev-

el.

• Deactivation/activation of the audible

signals.

Audible signals

You can hear an audible signal:

• At the end of the washing programme.

• When the appliance has a malfunction.

The activation of the audible signals is set

at the factory.

Do these steps to deactivate the audible

signals:

1. Switch on the appliance.

2. Make sure that the appliance is in set-

ting mode.

3. Press and hold the programme selec-

tion/cancel button until programme in-

dicator light A flashes and programme

indicator light B comes on.

4. Press the programme selection/cancel

button again.

– Programme indicator light A comes

on.

– Programme indicator light B starts to

flash.

5. Wait until programme indicator light A

goes off.

– Programme indicator light B contin-

ues to flash.

– The end indicator light comes on.

The audible signals are activated.

6. Press the programme selection/cancel

button again.

– The end indicator light goes off.

The audible signals are deactivated.

7. Switch off the appliance to save the op-

eration.

Do these steps to activate the audible sig-

nals:

1. Do the above procedure until the end

indicator light comes on.

ENGLISH 7

Washing programmes

Programme

Degree

of soil

Type of

load

Programme description

Intensive

Heavy

soil

Crockery,

cutlery,

pots and

pans

Prewash

Main wash up to 70°C

2 intermediate rinses

Final rinse

Drying

Normal

soil

Crockery,

cutlery,

pots and

pans

Prewash

Main wash up to 65°C

2 intermediate rinses

Final rinse

Drying

Quick

1)

Normal or

light soil

Crockery

and cutlery

Main wash up to 60°C

Final rinse

Eco

2)

Normal

soil

Crockery

and cutlery

Prewash

Main wash up to 50°C

1 intermediate rinse

Final rinse

Drying

Rinse & Hold

Any

Partial

load (to be

completed

later in the

day)

1 cold rinse (to prevent food scraps to

bond).

Detergent is not necessary with this

programme.

1) This is the perfect daily programme to clean a not fully load. Ideal for a family of 4 persons who only want to load

breakfast and dinner crockery and cutlery.

2) Test programme for test institutes. This is the economy washing programme. Please refer to separate leaflet

supplied, for test data. Available only in 3 languages (English, French, German) just for test institutes purpose.

Consumption values (for full washing cycle)

Programme Programme dura-

tion (minutes)

Energy consump-

tion (kWh)

Water consumption

(litres)

120-130 1,8-2,0 22-24

105-115 1,5-1,7 23-25

30 0,9 9

1)

130-140 1,0-1,2 14-16

12 0,1 5

1) The duration of this washing programme is prefixed (longer) than the others due to a prolonged drying and

washing phases.

ENGLISH 8

The pressure and temperature of the

water, the variations of power supply

and the quantity of dishes can change these

values.

Use of the appliance

Refer to the following instructions for each

step of procedure:

1. Make a check if the water softener level

is correct for the water hardness in your

area. If necessary set the water soften-

er.

2. Fill the salt container with dishwasher

salt.

3. Fill the rinse aid dispenser with rinse

aid.

4. Load cutlery and dishes into the dish-

washer.

5. Set the correct washing programme for

the type of load and soil.

6. Fill the detergent dispenser with the

correct quantity of detergent.

7. Start the washing programme.

If you use detergent tablets, refer to

the chapter 'Use of detergent'.

Setting the water softener

The water softener removes minerals and

salts from the water supply. Minerals and

salts can have bad effect on the operation

of the appliance.

Water hardness is measured in equivalent

scales:

• German degrees (dH°).

• French degrees (°TH).

• mmol/l (millimol per litre - international

unit for the hardness of water).

•Clarke.

Adjust the water softener to the water hard-

ness in your area. If necessary, contact your

local water authority.

Water hardness Water hardness setting

°dH °TH mmol/l Clarke manually electronically

51 - 70 91 - 125 9,1 - 12,5 64 - 88 2 10

43 - 50 76 - 90 7,6 - 9,0 53 - 63 2 9

37 - 42 65 - 75 6,5 - 7,5 46 - 52 2 8

29 - 36 51 - 64 5,1 - 6,4 36 - 45 2 7

23 - 28 40 - 50 4,0 - 5,0 28 - 35 2 6

19 - 22 33 - 39 3,3 - 3,9 23 - 27 2 5

15 - 18 26 - 32 2,6 - 3,2 18 - 22 1 4

11 - 14 19 - 25 1,9 - 2,5 13 - 17 1 3

4 - 10 7 - 18 0,7 - 1,8 5 - 12 1 2

< 4 < 7 < 0,7 < 5

1

1)

1

1)

1) No use of salt required.

ENGLISH 9

You must set the water softener man-

ually and electronically.

Manual adjustment

The appliance is set at the factory at posi-

tion 2.

1

2

Set switch to posi-

tion 1 or 2.

Electronic adjustment

The water softener is set at the factory at

level 5.

1. Switch on the appliance.

2. Make sure that the appliance is in set-

ting mode.

3. Press and hold the programme selec-

tion/cancel button.

4. Release the programme selection/can-

cel button when programme indicator

light A starts to flash and programme

indicator light B comes on.

5. Wait until programme indicator light B

goes off.

– Programme indicator light A starts to

flash.

– The end indicator light starts to flash.

6. Press the programme selection/cancel

button one time.

– Programme indicator light A starts to

flash.

– The setting function of the water soft-

ener is activated.

– The end indicator light flashes to

show the level of the water softener.

Example: 5 flashes, pause, 5 flashes,

pause, etc... = level 5.

7. Press the programme selection/cancel

button one time to increase the water

softener level by one step.

8. Press the on/off button to save the op-

eration.

Use of dishwasher salt

Caution! Only use dishwashers salt.

Types of salt that are not applicable

for dishwashers cause damage to the water

softener.

1

2

3

Fill the salt contain-

er with 1 litre of wa-

ter (only the first

operation).

4

Fill the salt contain-

er with 1,5-2,0 kg of

salt. Use the salt

funnel supplied.

ENGLISH 10

5

Make sure that

there is no grain of

salt outer of the salt

compartment.

6

It is normal that water overflows from

the salt container when you fill it with

salt.

Use of rinse aid

Caution! Only use branded rinse aid

for dishwashers.

Do these steps to fill the rinse aid dispenser:

1

2

3

+

-

M

A

X

4

Caution! Do not fill the rinse aid dis-

penser with other products (e.g. dish-

washer cleaning agent, liquid detergent).

There is a risk of damage to the appli-

ance.

Adjusting the dosage of rinse aid

The rinse aid dial is

set at the factory at

position 3.

To increase or de-

crease the dosage

refer to 'What to do

if...'

Loading cutlery and dishes

Helpful hints and tips

Caution! Only use the appliance for

household utensils that are applicable

for dishwashers.

Do not use the appliance to clean objects

that can absorb water (sponges, household

cloths, etc.).

ENGLISH 11

• Before you load cutlery and dishes, do

these steps:

– Remove all food remainings and deb-

ris.

– Make burnt, remaining food in pans

soft.

• While you load cutlery and dishes, do

these steps:

– Load hollow items (e.g. cups, glasses

and pans) with the opening down.

– Make sure that water does not collect

in the container or in a deep base.

– Make sure that cutlery and dishes do

not lie inside one another.

– Make sure that cutlery and dishes do

not cover other cutlery and dishes.

– Make sure that glasses do not touch

other glasses.

– Put small objects in the cutlery basket.

• Plastic items and pans with non-stick

coatings can keep water droplets. Plastic

items do not dry as well as porcelain and

steel items.

• Put light items in the upper basket. Make

sure that the items do not move.

Caution! Make sure that the spray

arms can move freely before you start

a washing programme.

Warning! Always close the door after

you load or unload the appliance. An

open door can be dangerous.

Arrange service

dishes and large

lids around the

edge of the lower

basket.

The rows of prongs

in the lower basket

can be flat to load

pots, pans and

bowls.

Use the cutlery

grids. If the dimen-

sions of the cutlery

prevent use of the

cutlery grids, re-

move them.

The cutlery basket

has two parts. To

disassemble the

parts, move them

horizontally, in op-

posite directions

and pull them

apart. To assemble

the parts, put them

together and move

them horizontally to

each other.

ENGLISH 12

Arrange the items to let water touch all

surfaces (left). For longer items, fold the

cup racks up (right).

Put plates only in the rear part of the

upper basket. Tilt them forward.

Adjustment of the height of the upper

basket

If you put large plates in the lower basket,

first move the upper basket to the upper

position.

Maximum height of the dishes in :

• Upper basket.

– Upper position: 22 cm.

– Lower position: 26 cm.

• Lower basket.

– Upper position: 33 cm.

– Lower position: 29 cm.

Do these steps to move the upper basket to

the upper position:

1. Pull the basket out until it stops.

2. Carefully lift basket from two sides until

the mechanism is engaged and the

basket is stable.

Do these steps to move the upper basket to

the lower position:

1. Pull the basket out until it stops.

2. Carefully lift the two sides just a bit up-

wards.

3. Hold the mechanism and let it fall back

down slowly.

Caution!

• Do not lift or lower the basket on

one side only.

• If the basket is in the upper position,

do not put cups on the cup racks.

Use of detergent

Only use detergents (powder, liquid or

tablet) that are applicable for dish-

washers.

Follow the data on the packaging:

• Dosage recommended by the manufac-

turer.

• Storage recommendations.

Do not use more than the correct quantity of

detergent to save an environment.

1

2

3

A

Fill the detergent

dispenser (A) with

detergent.

4

B

If you use a wash-

ing programme

with prewash

phase, put more

detergent in the

prewash detergent

compartment (B).

ENGLISH 13

5

A

6

Use of detergent tablets

Put the detergent tablet in the detergent

dispenser (A).

Detergent tablets contain:

•detergent

•rinse aid

• other cleaning agents.

Do these steps to use detergent tablets:

1. Make sure that the detergent tablets

are applicable for your water hardness.

Refer to the instructions from the manu-

facturer.

2. Set the lowest levels of water hardness

and rinse aid dosage.

It is not necessary to fill the salt con-

tainer and the rinse aid dispenser.

Do these steps when the drying results

are not satisfactory:

1. Fill the rinse aid dispenser with rinse

aid.

2. Set the rinse aid dosage to position 2.

Do these steps to use the detergent

powder again:

1. Fill the salt container and the rinse aid

dispenser.

2. Set the water softener to the highest

level.

3. Do a washing programme without

dishes.

4. Adjust the water softener. Refer to the

chapter 'Setting the water softener'.

5. Adjust the rinse aid dosage.

Different brands of detergent dissolve

in different times. Some detergent tab-

lets do not have the best cleaning results

during short washing programmes. Use long

washing programmes when you use deter-

gent tablets to fully remove the detergent.

Setting and starting a washing programme

Set the washing programme with the

door ajar. The washing programme

only starts after you close the door. Until

then it is possible to modify the settings.

Do these steps to set and start a washing

programme:

1. Switch on the appliance.

2. Make sure that the appliance is in set-

ting mode.

3. Press the programme selection/cancel

button again and again to set the

washing programme. Refer to the

chapter 'Washing programmes'.

– The programme indicator light comes

on.

4. Close the door.

– The washing programme starts auto-

matically.

When the washing programme oper-

ates, you cannot change the pro-

gramme. Cancel the washing programme.

Warning! Only interrupt or cancel a

washing programme if necessary.

Caution! Open the door carefully. Hot

steam can come free.

Cancelling a washing programme

1. Press and hold the programme selec-

tion/cancel button for approximately 3

seconds.

– The programme indicator light goes

off.

– The end indicator light starts to flash.

2. Release the programme selection/can-

cel button to cancel the washing pro-

gramme.

At this time you can do these steps:

ENGLISH 14

1. Switch off the appliance.

2. Set a new washing programme.

Fill the detergent dispenser with detergent

before you set a new washing programme.

Interrupting a washing programme

Open the door.

• The programme stops.

Close the door.

• The programme continues from the point

of interruption.

Setting and starting a washing

programme with delay start

1. Press the on/off button.

2. Set a washing programme.

– The programme indicator light comes

on.

3. Press the delay start button.

– The delay start indicator light comes

on.

4. Close the door.

– The countdown of the delay start

starts.

– When the countdown is completed,

the washing programme starts auto-

matically.

Do not open the door during the

countdown to prevent interruption of

the countdown. When you close the door

again, the countdown continues from the

point of interruption.

Cancelling a delay start:

1. Open the door.

2. Press the delay start button.

– The delay start indicator light goes

off.

3. Close the door.

– The programme starts immediately.

End of the washing programme

Switch off the appliance in these conditions:

• The appliance stops automatically.

• The audible signals for the end of the

programme operate.

1. Open the door.

– The end indicator light comes on.

– The programme indicator light stays

on.

2. Press the on/off button.

3. For better drying results, keep the door

ajar for some minutes before you re-

move the dishes.

Let the dishes cool down before you re-

move them from the appliance. Hot dishes

are easily damaged.

Removing the load

• First remove items from the lower basket,

then from the upper basket.

• There can be water on the sides and

door of the appliance. Stainless steel be-

comes cool more quickly than the dishes.

Care and cleaning

Warning! Switch the appliance off

before you clean the filters.

Cleaning the filters

Important! Do not use the appliance

without the filters. Make sure that the

installation of the filters is correct. Incorrect

installation will cause unsatisfactory

washing results and damage to the

appliance.

1 2

A

C

B

Fully clean the filters

A, B and C below

running water.

ENGLISH 15

3

1

2

To remove filters B

and C, turn the

handle approxi-

mately 1/4 anti-

clockwise.

4

A

Remove the flat fil-

ter A from the bot-

tom of the appli-

ance.

5

2

1

Put the filter system

in position. To lock

the filter system,

turn the handle

clockwise until it

locks in position.

Important! Do not remove the spray arms.

If the holes in the spray arms become clog-

ged, remove remaining parts of soil with a

cocktail stick.

Long periods of non-operation

Do these steps when you do not use the ap-

pliance for a long period:

1. Disconnect the mains plug from the

mains socket.

2. Close the water tap.

3. Keep the door open to prevent un-

pleasant smells.

4. Keep the inner side of the appliance

clean (filters especially).

External cleaning

Clean the external surfaces of the appliance

and control panel with a damp soft cloth.

Only use neutral detergents. Do not use

abrasive products, scouring pads or sol-

vents (acetone, trichloroethylene etc...).

Frost precautions

Caution! Do not install the appliance

where the temperature is below 0 °C.

The manufacturer is not responsible for

damage because of frost.

If not possible, empty the appliance and

close the door. Disconnect the water inlet

hose and remove water from the water inlet

hose.

What to do if…

The appliance does not start or stops during operation.

If there is a fault, first try to find a solution to the problem yourself. If you cannot find a

solution to the problem yourself, contact your dealer or the After Sales Service.

Problem Possible cause Solution

• Continuous flash

of the light of the

running pro-

gramme.

• Intermittent au-

dible signal.

• 1 flash of the

end indicator

light.

The water tap is blocked or fur-

red with limescale.

Clean the water tap.

The water tap is closed. Open the water tap.

The filter in the water inlet hose is

blocked.

Clean the filter.

ENGLISH 16

Problem Possible cause Solution

Malfunction:

The dishwasher

does not fill with

water.

The connection of the water inlet

hose is not correct. The hose can

be kinked or squashed.

Make sure that the connection is

correct.

• Continuous flash

of the light of the

running pro-

gramme.

• Intermittent au-

dible signal.

• 2 flashes of the

end indicator

light.

Malfunction:

The dishwasher

will not drain.

There is a blockage in the sink

spigot.

Clean the sink spigot.

The connection of the water

drain hose is not correct. The

hose can be kinked or squashed.

Make sure that the connection is

correct.

• Continuous flash

of the light of the

running pro-

gramme.

• Intermittent au-

dible signal.

• 3 flashes of the

end indicator

light.

Malfunction:

The anti-flood de-

vice operates.

Close the water tap and contact your local After Sales Service.

Malfunction:

The programme

does not start.

The appliance door is not closed. Close the door.

Mains plug is not connected in. Put in the mains.

The fuse has blown out in the

household fuse box.

Replace the fuse.

Delay start is set. Cancel the delay start to start the

programme immediately.

After the check, switch on the appliance. The programme continues from the point of inter-

ruption. If the malfunction shows again, contact your After Sales Service.

When the cleaning results are not satisfactory:

Problem Possible cause Solution

The dishes are

not clean

The selected washing programme

is not applicable for the type of

load and soil.

Set different washing programme.

ENGLISH 17

Problem Possible cause Solution

The baskets are loaded incorrectly

so that water cannot reach all sur-

faces.

Load the baskets correctly.

Spray arms do not turn freely be-

cause of incorrect arrangement of

the load.

Make sure that the cutlery and

dishes do not block the spray arms.

The filters are dirty or not correctly

installed.

Make sure that the filters are clean

and installed correctly.

The quantity of detergent is too lit-

tle or missing.

Make sure that the quantity of de-

tergent in detergent dispenser is

correct.

Limescales

particles on

the dishes

The salt container is empty. Fill the salt container with salt.

The water softener is adjusted on a

wrong level.

Set the water softener.

The salt container cap is not closed

correctly.

Make sure that the salt container is

closed correctly.

The dishes are

wet and dull

No rinse aid has been used. Set the rinse aid dosage.

The rinse aid dispenser is empty. Fill the rinse aid dispenser.

There are

streaks, milky

spots or a blu-

ish coating on

glasses and

dishes

Wrong dosage of rinse aid. Decrease the rinse aid dosage.

Dry water

drop signs on

glasses and

dishes

Wrong dosage of rinse aid. Increase rinse aid dosage.

The detergent can be the cause. Use different type of detergent.

Technical data

Dimensions Width (cm) 59.6

Height (cm) 85.8 - 93.8

Depth (cm) 55.0

Water supply pressure

1)

Minimum

Maximum

0,5 bar (0,05 MPa)

8 bar (0,8 MPa)

Capacity (place settings) 12

Energy class A

Drying class A

ENGLISH 18

Noise (dB(A)) 49

Average annual energy

consumption (kWh)

2)

311

Average annual water con-

sumption (litres)

2)

4480

1) If the pressure in your area is lower or higher, please contact your After Sales Service.

2) The data is based on the washing programme for test institutes assuming 280 cycles per a year.

Information on the electrical connection, voltage and overall power is given on the

rating plate on the inner edge of the dishwasher door.

Installation

Caution! Refer to the assembly

instructions, in order to proceed with

the installation.

Warning! Make sure that mains plug is

disconnected from the mains socket

during installation.

Place the appliance on the floor and install

it under a counter (kitchen worktop or sink).

If a repair is necessary, the appliance must

be easily accessible for the engineer.

Put the appliance adjacent to a water tap

and a drain.

For the venting of the dishwasher only wa-

ter fill, water drain and power supply cable

openings are necessary.

Water connection

This appliance has a special inlet hose

for water stop later defined as aqua-

lock.

Water inlet hose

Connected the appliance to a hot (max.

60°) or cold water supply.

If the hot water comes from alternative

sources of energy that are more environ-

mentally friendly (e.g. solar or photovoltaic

panels and aeolian), use a hot water supply

to decrease energy consumption.

Connect the inlet hose to a water tap with

an external thread of 3/4".

Caution! Do not use connection hoses

from an old appliance.

Caution! If you connect the appliance

to new pipes or pipes that are not used

for a long time, we recommend to run the

water for some minutes before you connect

the inlet hose.

Aqualock inlet hose

The inlet hose is a high pressure resistant. It

can hold pressure at maximum 6 MPa. From

external the inlet hose has a sheathing

against eventual damages. If the inner hose

breaks, the water that is in the hose will be-

came dark. You can see it across the special

transparent sheathing. Turn off the water

tap immediately and contact the After Sales

Service.

ENGLISH 19

A

B

The aqualock inlet

hose is installed

with a safety device

to prevent acciden-

tal loosening. To

disconnect the hose:

•Press the lever

(B).

• Turn the retaining

ring (A) anticlock-

wise.

Turn the inlet hose

to the left or the

right to suit the in-

stallation. Tight the

locknut correctly to

prevent water

leaks.

If you use a in-

let hose exten-

sion the total

reached length

must be no longer

than 4 metres.

Drain hose

A

If you connect the

water drain hose to

a water trap under

the sink, remove the

plastic membrane

(A). If you do not re-

move the mem-

brane, remaining

food can cause a

blockage in the

drain hose spigot.

Caution! Make

sure that the

water couplings are

tight to prevent wa-

ter leakage.

Electrical connection

Warning! The manufacturer is not

responsible if you do not follow these

safety precautions.

This appliance needs to be earthed accord-

ing to safety precautions.

Make sure that the rated voltage and type

of power on the rating plate agree with the

voltage and the power of the local power

supply.

Always use a correctly installed shockproof

socket.

Do not use multi-way plugs, connectors and

extension cables. There is a risk of fire.

Do not replace the mains cable yourself.

Contact the After Sales Service.

Make sure that the mains plug is accessible

after installation.

Do not pull the mains cable to disconnect

the appliance. Always pull the mains plug.

This appliance complies with the E.E.C. Di-

rectives.

Environment concerns

The symbol on the product or on its

packaging indicates that this product may

not be treated as household waste. Instead

it should be taken to the appropriate

collection point for the recycling of electrical

and electronic equipment. By ensuring this

product is disposed of correctly, you will

help prevent potential negative

consequences for the environment and

human health, which could otherwise be

caused by inappropriate waste handling of

this product. For more detailed information

about recycling of this product, please

ENGLISH 20

La page charge ...

IKEA RDWTI60 Manuel utilisateur

IKEA RDWTI60 Manuel utilisateur

dans d''autres langues