Fontaine by Italia MFF-PNTS-CP Guide d'installation
- Catégorie
- Robinets
- Taper
- Guide d'installation
Ce manuel convient également à
5N0C045801CP/AP/HA/HBW0Flange
3
4
2
5P0040900CP/AP/HA/HBW0Shower Arm
5F0003100CP/AP/HA/HBW0A0Showerhead
5D0M0290PLFlow Restrictor
Part No.DescriptionNO.
5R0R0175PLO-ring
1
5
5Y0193700CP/AP/HA/HBW0Handle Assembly
6
Cinta selladora para rosca
Ruban pour tuyau
Pipe Tape
Destornillador cruciforme
Tournevis Phillips
Phillips ScrewdriverAdjustable Wrench
Clé à molette
Llave ajustable
MFF-PNTS-CP
MFF-PNTS-BN
Pont Neuf Collection
Single-Handle Tub and Shower Trim
Installation/Installation/Instalación
CUSTOMER SERVICE
TOLL-FREE 1-877-482-5422
Tools You Will Need / Outils dont vous aurez besoin / Herramientas necesarias
Replacement Parts / Pièces de rechange / Repuestos
SAFETY TIPS
• If you use soldering for the installation of the faucet, the seats, cartridges and washers will have to be removed
before using flame. Otherwise, warranty will be void on those parts.
• Cover your drain to avoid losing parts.
• 0℃~55℃.
CONSIGNES DE SÉCURITÉ
• Si vous posez le robinet par brasage, il est essentiel de retirer les sièges, les cartouches et les rondelles avant
d’appliquer la flamme, faute de quoi la garantie sur ces pièces sera annulée.
• Couvrez le drain pour ne pas perdre des pièces.
• 0℃~55℃.
CONSEJOS DE SEGURIDAD
• En el caso de utilizar soldadura para instalar el grifo, remueva los asientos, cartuchos y arandelas antes de usar la
llama. De lo contrario, se anulará la garantía para esos componentes.
• Tape la boca del desagüe para prevenir la pérdida de piezas pequeñas.
• 0℃~55℃.
Revised 6-2018
MFF-PNTS-CP - Polished Chrome
MFF-PNTS-BN - PVD Brushed Nickel
1
2
5
6
3
4
MFF-PNTS-CP
MFF-PNTS-BN
Installation/Installation/Instalación
Revised 6-2018 Revised 6-2018
Thread the shower head
clockwise onto the shower arm.
11
Thread Teflon Tape
Apply teflon tape to the tub spout
nipple and thread the spout
clockwise onto the tub spout nipple.
1
Remove the mud guard.
Carefully slide the escutcheon onto
the valve.
2 3
Place handle assembly on valve
and rotate clockwise to secure
escutcheon.
Re-install the trimmed stem and
nipple on the valve.
Carefully slide the escutcheon onto
the valve and place handle assembly
on valve and rotate clockwise to
secure escutcheon.
9
If handle assembly will not secure
escutcheon to the wall, measure and
note the distance ‘XX’(the distance
between the bottom of the handle
assembly and the escutcheon)
Unscrew the handle assembly
counterclockwise from valve and
remove the escutcheon.
5 6
Cut stem and nipple the amount
noted in step # 4. (Never cut the
stem and nipple while still on the
valve. This may damage the valve.)
12
Turn on the handle and check the
function of the spout.
13
Pull up on the lift knob of the spout.
Check the diverter function.
Apply teflon tape to the shower arm
and thread clockwise onto the
nipple. Then slide the flange down.
4
a
b
}
7
a
8
Thread Teflon Tape
10
b
-
1
-
2
Fontaine by Italia MFF-PNTS-CP Guide d'installation
- Catégorie
- Robinets
- Taper
- Guide d'installation
- Ce manuel convient également à
dans d''autres langues
Documents connexes
-
Fontaine by Italia MFF-PNS-BN Guide d'installation
-
Fontaine by Italia MFF-HVS-CP Guide d'installation
-
-
-
-
-
-
-
-