Whirlpool WDF560SAFT Le manuel du propriétaire
- Catégorie
- Lave-vaisselle
- Taper
- Le manuel du propriétaire
THANK YOU for purchasing this high-quality product. If you should experience a problem not covered in TROUBLESHOOTING,
please visit our website at www.whirlpool.com for additional information. If you still need assistance, call us at 1-800-253-1301.
In Canada, visit our website at www.whirlpool.ca or call us at 1-800-807-6777.
You will need your model and serial number located near the door on the right-hand or left-hand side of the dishwasher interior.
Dishwasher Safety
DISHWASHER
USER INSTRUCTIONS
TABLE OF CONTENTS
DISHWASHER SAFETY............................................................. 1
WHAT’S NEW IN YOUR DISHWASHER................................... 3
ENERGY...................................................................................... 3
PERFORMANCE ........................................................................ 3
PARTS AND FEATURES............................................................ 4
QUICK STEPS ............................................................................ 5
DISHWASHER USE.................................................................... 6
CYCLE AND OPTION DESCRIPTIONS.................................... 8
DISHWASHER FEATURES...................................................... 10
FILTRATION SYSTEM ............................................................. 11
DISHWASHER CARE............................................................... 12
TROUBLESHOOTING.............................................................. 13
WARRANTY..............................................................................16
You can be killed or seriously injured if you don't immediately
You
can be killed or seriously injured if you don't
follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING
W10852541A
2
IMPORTANT SAFETY INSTRUCTIONS
WARNING:
When using the dishwasher, follow basic precautions, including the following:
SAVE THESE INSTRUCTIONS
■ Read all instructions before using the dishwasher.
■ Use the dishwasher only for its intended function.
■ Use only detergents or rinse agents recommended for use in
a dishwasher, and keep them out of the reach of children.
■ When loading items to be washed:
1) Locate sharp items so that they are not likely to damage
the door seal; and
2) Load sharp knives with the handles up to reduce the risk
of cut-type injuries.
■ Do not wash plastic items unless they are marked
“dishwasher safe” or the equivalent. For plastic items not so
marked, check the manufacturer's recommendations.
■ Do not touch the heating element during or immediately after
use.
■ Do not operate the dishwasher unless all enclosure panels
are properly in place.
■ Do not tamper with controls.
■ Do not abuse, sit on, or stand on the door, lid, or dish racks
of the dishwasher.
■ To reduce the risk of injury, do not allow children to play in
or on the dishwasher.
■ Under certain conditions, hydrogen gas may be produced in
a hot water system that has not been used for two weeks or
more. HYDROGEN GAS IS EXPLOSIVE. If the hot water
system has not been used for such a period, before using
the dishwasher turn on all hot water faucets and let the
water flow from each for several minutes. This will release
any accumulated hydrogen gas. As the gas is flammable,
do not smoke or use an open flame during this time.
■ Remove the door or lid to the washing compartment
when removing an old dishwasher from service or
discarding it.
GROUNDING INSTRUCTIONS
SAVE THESE INSTRUCTIONS
■
For a grounded, cord-connected dishwasher:
The dishwasher must be grounded. In the event of a
malfunction or breakdown, grounding will reduce the risk of
electric shock by providing a path of least resistance for
electric current. The dishwasher is equipped with a cord
having an equipment-grounding conductor and a grounding
plug. The plug must be plugged into an appropriate outlet
that is installed and grounded in accordance with all local
codes and ordinances.
WARNING:
Improper connection of the equipment-
grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or service representative
if you are in doubt whether the dishwasher is properly
grounded. Do not modify the plug provided with the
dishwasher; if it will not fit the outlet, have a proper outlet
installed by a qualified electrician.
■
For a permanently connected dishwasher:
The dishwasher must be connected to a grounded metal,
permanent wiring system, or an equipment-grounding
conductor must be run with the circuit conductors and
connected to the equipment-grounding terminal or lead on
the dishwasher.
Tip Over Hazard
Do not use dishwasher until completely installed.
Do not push down on open door.
Doing so can result in serious injury or cuts.
WARNING
3
What’s New in Your Dishwasher
Energy
Performance
Congratulations on purchasing your water and energy efficient dishwasher! This dishwasher cleans by spraying the
dishes with water and pauses to allow the detergent to soak into and release the soils on the dishes. The cycles are
longer due to the soak and pauses for exceptional cleaning. Your dishwasher contains an optical water sensor. The
optical water sensor is used to determine the optimum water and energy consumption for great cleaning
performance. Efficient dishwashers run longer to save water and energy, just as driving a car slower saves on gas.
The first cycle using the sensor will run longer to calibrate the optical sensor.
Rinse Aid
Using rinse aid will optimize your drying and wash performance.
This dishwasher is specifically designed to be used with rinse aid
for improved drying performance and controlling buildup of hard
water deposits. Energy efficient dishwashers use less water and
energy, so they depend on the water “sheeting” action of rinse
aid for total optimal performance.
Detergent
The United States and Canada have passed regulations limiting
the amount of phosphorus (phosphates) in the household
dishwasher detergents to no more than 0.5%, where previous
detergents contained 8.7%. Major manufacturers have
reformulated their dishwasher detergent for this change in
detergents as another step in eco-conscious awareness. With
these changes, we recommend quality tablets and packs for
convenience and improved performance.
Filtration System
Your dishwasher has the latest technology in dishwasher
filtration. This triple filtration system minimizes sound and
optimizes water and energy conservation while providing optimal
cleaning performance. Maintenance of your filters regularly will
sustain peak cleaning performance. We suggest you clean both
your upper and lower filters and rinse under running water at
least once a month.
SLIDE
SLID
E
P
U
S
H
D
O
W
N
&
T
U
R
N
L
O
C
K
U
N
L
O
C
K
4
Parts and Features
5
Quick Steps
1
Prepare and load
dishwasher.
Spin the spray
arms. They
should turn
freely.
4
Start dishwasher.
Push door firmly closed.
Select the wash cycle and
options, and then press
START/RESUME. To use
the same cycle and options
used previously, press
START/RESUME twice.
2
Add detergent and rinse aid.
5
Unload dishwasher
and clean the filter.
See “Recommended Time
Interval to Clean Your
Filter” in the “Filtration
System” section for the
recommended cleaning
schedule.
3
Select a cycle and option (cycles and options
vary by model).
SLID
E
S
LID
E
L
O
C
K
U
N
L
O
C
K
P
U
S
H
D
O
W
N
&
T
U
R
N
6
Dishwasher Use
Prepare and Load the Dishwasher
IMPORTANT: Remove leftover food, bones, toothpicks, and
other hard items from the dishes. Remove labels from
containers before washing.
■ Check that when dishwasher door is closed, no items are
blocking detergent dispenser.
■ Tough soiled items should be loaded with soiled surfaces facing
down and inward to the spray. This will improve cleaning and
drying results.
■ Avoid overlapping items like bowls or plates that may trap food.
■ Place plastics, small plates, and glasses in the upper rack.
Wash only plastic items marked “dishwasher safe.”
■ To avoid thumping/clattering noises during operation, load
dishes so they do not touch one another. Make sure lightweight
load items are secured in racks.
■ Use slots in the covers and suggested loading patterns to keep
your silverware separated for optimum wash.
NOTE: Silverware basket may vary by model.
■ Check that nothing blocks the upper or lower spray arms.
Add Detergent
Premeasured Detergents
High quality premeasured tablets
and packs are recommended for
improved performance.
Quality tablets and packs have
been proven better than powder,
liquid, or gel detergents at
reducing filming on dishes. Using
tablets and packs over time will
start to reduce or eliminate white
film. They are suitable for all
hardness and soil levels. Also,
by using a rinse aid, you can
minimize repeat buildup of white film (not all packs and tablets
contain rinse aid). Always place premeasured detergents in main
compartment and slide lid closed.
NOTE: Follow instructions on the package when using other
dishwasher detergent types. See the complete owners manual for
more details about powders, liquids, and gels.
■ Use automatic dishwasher detergent only. Add detergent just
before starting a cycle.
■ Fresh automatic dishwasher detergent results in better
cleaning. Store tightly closed detergent container in a cool,
dry place.
STEP 1
Upper rack Lower rack
■ When loading silverware, always place sharp
items pointing down and avoid “nesting.”
■ If your silverware does not fit into the
designated slots, flip the covers up and mix
silverware types to keep them separated.
Items in rack can
block the spray arms.
STEP 2
To close lid To open lid
Place selected detergent in
the dispenser. Place finger,
as shown, and slide lid closed.
Press firmly until it clicks.
Push OPEN, as shown, and the
lid will slide open.
SLID
E
SLIDE
SLIDE
7
Powders and Gels
*The prewash compartment is on top of the sliding door of
the dispenser.
**A full main wash compartment contains 2 Tbsp. (30 ml).
IMPORTANT: Extremely hard water mineral deposits (15 grains
per U.S. gallon or more) can cause damage to your dishwasher
and make it difficult to achieve good results. A water softener is
recommended to avoid damage and achieve good results.
NOTE: Follow instructions on the package when using other
dishwasher detergent types.
Rinse Aid
IMPORTANT: Your dishwasher is designed to use rinse aid. The
use of rinse aids greatly improves drying by allowing water to drain
from the dishes after the final rinse. Rinse aid also keeps water
from forming droplets that can dry as spots or streaks.
Filling the dispenser
The dispenser holds 5 oz (150 mL) of rinse
aid. Under most conditions, this will last
1 to 3 months.
NOTE: Indicator reads correct fill level when
door is completely opened.
1. To add rinse aid, open the
rinse dispenser lid by gently
pushing in the center of the
lid with your thumb and
pulling up on the edge.
2. Pour rinse aid into the
opening until the dispenser
is full. Do not overfill.
3. Clean up any spilled rinse aid.
Spilled rinse aid can create excessive suds.
4. Then, close the dispenser by pushing down gently on the lid.
■ To add rinse aid: Open the rinse dispenser lid by gently pushing
in the center of the lid with your thumb and pulling up on the
edge. Pour rinse aid into the opening until the dispenser is full.
Then, close the dispenser by pushing down gently on the lid.
NOTE: For most water conditions, the factory setting will give
good results.
Rinse Aid Setting
Your rinse aid dispenser is adjustable. For
most water conditions, the factory setting will
give good results. If you have hard water and
notice calcium buildup on your dishware, you
may want to try a higher setting. If you notice
foam in your dishwasher, use a lower setting.
To adjust the setting:
Turn the arrow adjuster to a higher number to
increase the amount of rinse aid.
Select a Cycle (varies by model)
See “Cycle and Option Descriptions” charts in the following section.
Heavier cycles and options affect cycle length.
Select Options (varies by model)
See “Cycle and Option Descriptions” charts in the following section.
You can customize your cycles by pressing the options desired.
Start or Resume a Cycle
■ Run hot water at the sink nearest your dishwasher until the
water is hot. Turn off water.
■ For best dishwashing results, water should be 120ºF (49ºC)
as it enters the dishwasher.
■ Push door firmly closed. Select the wash cycle and options
desired. Press START/RESUME to start the diswasher.
NOTE: To repeat the same cycle and options used previously,
press START/RESUME twice.
■ You can add an item anytime at the beginning of the cycle.
Open the door slowly and add the item. Close the door firmly.
Press START/RESUME.
Water
Hardness
Soil Level Pre-Wash
Compartment*
Main Wash
Compartment
Soft
(0-4 grains
per U.S.
gallon)
Light None “Soft” fill line
Normal None “Soft” fill line
Heavy Full “Soft” fill line
Medium
(5-9 grains
per U.S.
gallon)
Light Full Full**
Normal Full Full**
Heavy Full Full**
Hard
(10-14 grains
per U.S.
gallon)
Light Full Full**
Normal Full Full**
Heavy Full Full**
STEP 3
SLIDE
Full
Add
Pre Wash
OPEN
SLIDE
STEP 4
STEP 5
8
Cycle and Option Descriptions
Estimated cycle times may increase or decrease depending on water temperature, soil conditions, dish load size, and options selected.
You can customize your cycle by selecting an option.
See option selections. If you change your mind, press the option again to turn off the option or select a different option. You can change
an option anytime before the selected option begins. At each stage of a wash cycle, you may hear noises that you are not used to hearing
in your previous dishwasher. Each cycle will provide a series of pauses and water sprays throughout the wash cycle. This is normal and
will provide optimal cleaning performance.
IMPORTANT: The sensor in your dishwasher monitors the soil level. Cycle time and/or water usage can vary as the sensor adjusts the
cycle for the best wash performance. If the incoming water is less than the recommended temperature or food soils are heavy, the cycle
will automatically compensate by adding time, heat, and water as needed.
CYCLE SELECTIONS
CYCLES SOIL LEVEL ESTIMATED
WASH TIME
DISPLAYED*
H:MM W/O
OPTIONS
WATER USAGE
GALLONS
(LITERS)
The most advanced and versatile cycle. This cycle senses load size,
soil amount, and toughness of soil, to adjust the cycle for improved
performance, using only the amount of water and energy needed.
Use for all soil levels.
All soil levels 2:30 3.38 to 7.4
(12.8 to 28.0)
Use for hard-to-clean, heavily soiled pots, pans, casseroles,
and tableware.
Heavy 3:23 7.4 (28.0)
This cycle with only the Heat Dry option selected, and without other
options selected, is recommended to completely wash and dry a full load
of normally soiled dishes. The energy usage label is based on this cycle
and option combination.
All soil levels 2:21 2.4 to 7.4
(9.09 to 28.0)
Use for lightly soiled items. It saves energy. Light 2:21 2.72 (10.29)
For fast results, 1-Hour Wash will clean dishes using slightly more water
and energy. For improved drying, select the Heat Dry option.
NOTE: Some detergents are not recommended for short wash cycles.
Please refer to your detergent packaging for more information.
Light 1:00 7.87 (29.8)
9
OPTION SELECTIONS
OPTIONS CAN BE
SELECTED
WITH
WHAT IT DOES ADDED TIME
TO CYCLE
ADDED
WATER
GALLONS
(LITERS)
Delay displays how many hours before the cycle will begin.
To delay the start:
1. Select a wash cycle and options.
2. Press the Delay button. Each time you press DELAY, it
will display the next available delay time.
3. Press START to begin the delay countdown.
Available
with any
cycle
Delays start of a
cycle up to
24 hours
.
NOTE: If the door is opened, such as to add a dish, the Start button must be pressed to resume the delay countdown.
Sanitizes dishes and glassware in accordance with NSF
International NSF/ANSI Standard 184 for Residential
Dishwashers. Certified residential dishwashers are not
intended for licensed food establishments. Only sanitizing
cycles have been designed to meet the requirements of
the NSF/ANSI 184 performance standard for soil removal
and sanitization efficacy. There is no intention, either
directly or indirectly, that all cycles on a NSF/ANSI 184
certified dishwasher meet the NSF/ANSI 184 performance
standard for soil removal and sanitization efficacy.
Sani Rinse indicator is lit at the end of the cycle if the Sani
Rinse option was successfully completed. If indicator does
not light, it is probably due to the cycle being interrupted.
Sensor
Heavy
Normal
Raises the main
wash temperature
to 135°F (57°C)
and the final rinse
temperature to
156°F (69°C).
0:05 to 1:06 0 to 3.9
(0 to 14.6)
Raises water temperature to improve cleaning for loads
containing tough, baked-on food.
Sensor
Heavy
Normal
Raises the main
wash temperature
to 135°F (57°C).
0:05 to 0:13 0 to 3.9
(0 to 14.6)
Turns the heating element on at the end of the wash
portion of the cycle. Its shorter heating time uses
significantly less energy compared to using Heat Dry.
Available
with any
cycle
0:11 0
Dries dishes with heat. This option, with the use of rinse
aid, will provide the best drying results. Plastic items are
less likely to deform when loaded in the top rack. Use Heat
Dry for optimum drying performance or turn the Heat Dry
option off for air dry.
Sensor
Heavy
Normal
1-Hour
Wash
Uses a heating
element to speed
drying times.
Heat Dry option
defaults to ON
when any cycle is
selected except
for 1-Hour Wash
and Light.
0:08 to 0:46 0
Control
Lock
Use the Control Lock option to avoid unintended use of dishwasher between cycles, or cycle and option changes during
a cycle.
To turn on Control Lock, press and hold SANI RINSE for 3 seconds. Control Lock light will stay on for a short time, indicating
that it is activated. When the Lock indicator is lit, all buttons are disabled. If you press any button while your dishwasher is
locked, the light flashes 3 times. The dishwasher door can still be opened/closed while the controls are locked.
To turn off Control Lock, press and hold SANI RINSE for 3 seconds. Control Lock light turns off.
10
Dishwasher Features
Your Whirlpool dishwasher may have some or all of these features.
Removable Top Rack
The removable top rack allows you to wash larger items such as pots, roasters, and cookie sheets in the bottom rack.
IMPORTANT: Remove dishes prior to removing the top rack from dishwasher.
To remove the rack
1. To gain access to the track stops,
pull the upper rack forward about
halfway out of the tub.
2. Press on the edge of the ridged area
on the track stop while tipping the
track stop toward the center of the
dishwasher. This action releases a
small retaining tab that locks the
track stop to the track. (See “Track
stop - Left.”)
NOTE: It is helpful to use two hands. Take special note of the
orientation of the track stops
3. With the retaining tab released, pull the track stop straight
toward the opposite track to remove it.
4. After removing both track stops, carefully pull the top rack out
of the tracks by rolling it toward you.
5. Replace the track stops by coming up from under the track
and slipping the track stop into the lower slot of the track (See
“Track stop - Right.”) and rotate the track stop into place. Then
press on the edge of the ridged area while pushing the track
stop straight toward the track. This action locks the retaining
tab back into place.
6. Test the track stop by pulling it toward the opposite track to
ensure that it is locked in place.
To replace the rack
1. Gently pull the tracks forward in
dishwasher until they stop.
Remove track stops. (See steps
1-3 above.)
2. Place the back wheels on each
side of the rack into the track
and roll the rack into the tracks,
but do not push the rack all the
way into the tub.
3. Insert front rack wheels on each
side of the rack into the track.
4. Slide the rack into the
dishwasher.
5. Replace the track stops by coming up from under the track
and slipping the track stop into the lower slot of the track (See
“Track stop - Right.”) and rotate the track stop into place. Then
press on the edge of the ridged area while pushing the track
stop straight toward the track. This action locks the retaining
tab back into place.
6. Test the track stop by pulling it toward the opposite track to
ensure that it is locked in place.
IMPORTANT: Be sure that the track stops are locked in place
and cannot be easily removed. They keep the rack from coming
out of the track.
CONTROLS AND CYCLE STATUS
CONTROL PURPOSE COMMENTS
Press to start or resume a wash cycle.
If the door is opened during a cycle or the power is interrupted, the Start/Resume button LED flashes. Cycle will
not resume until door is closed and Start/Resume is pressed.
Press to cancel wash cycle.
Close the door firmly. Press and hold START/RESUME or 3 seconds. The dishwasher starts a 2-minute drain
(if needed). Let dishwasher drain completely.
To follow progress of
your dishwasher cycle.
NOTE: Indicators shown
are not available on
all models.
The Clean indicator glows when a cycle is finished.
If you select the Sani Rinse option, when the cycle is finished, the “Sanitized” indicator
glows. If your dishwasher did not properly sanitize your dishes, the light flashes at the
end of the cycle. This can happen if the cycle is interrupted, or water could not be
heated to required temperature. The light goes off when you open and close door or
when you cancel the cycle.
Track stop - Left
Track stop - Right
11
Filtration System
Your dishwasher has the latest technology in dishwasher filtration. This triple filtration system minimizes sound and optimizes water and
energy conservation while providing superior cleaning performance. Throughout the life of your dishwasher, the filter will require
maintenance to sustain peak cleaning performance.
It is very easy to remove and maintain the filters. The chart below shows the recommended cleaning frequency.
*We recommend this practice because it will conserve the water and energy that you would have used to prepare your dishes. This will
also save you time and effort.
Very Hard Water
If you have hard water (above 15 grains), clean your filter at least
once per month. Buildup of white residue on your dishwasher
indicates hard water. For tips on removing spots and stains, see
“Troubleshooting” section.
Cleaning Instructions
IMPORTANT: Do not use wire brush, scouring pad, etc., as they
may damage the filters.
Rinse filter under running water until most soils are removed. If you
have hard-to-remove soils or calcium deposits from hard water, a
soft brush may be required.
The triple filter system consists of 2 parts, an upper filter assembly and
a lower filter.
■ The upper filter assembly keeps oversized items and foreign objects,
along with very fine food particles, out of the pump.
■ The lower filter keeps food from being recirculated onto your dishware.
The filters may need to be cleaned when:
■ Visible objects or soils are on the Upper Filter Assembly.
■ There is degradation in cleaning performance (that is, soils still present
on dishes).
■ Dishes feel gritty to the touch.
RECOMMENDED TIME INTERVAL TO CLEAN YOUR FILTER
Number of Loads
Per Week
If you only scrape before loading* If you scrape and rinse before loading If you wash before loading
8-12 Every 2 months Every 4 months Once per year
4-7 Every 4 months Once per year Once per year
1-3
Twice per year Once per year Once per year
Upper Filter
Assembly
Lower Filter
Filter Removal Instructions
1. Turn the Upper Filter
Assembly ¼ turn
counterclockwise
and lift out.
2. Separate the upper
filter assembly by
gently pulling apart.
3. Clean the filters
as shown.
To remove Upper Filter Assembly
L
O
C
K
U
N
L
O
C
K
P
U
S
H
D
O
W
N
&
T
U
R
N
P
U
S
H
D
O
W
N
&
T
U
R
N
L
O
C
K
U
N
L
O
C
K
12
IMPORTANT: To avoid damage to dishwasher, do not operate your
dishwasher without the filters properly installed. Be sure the Lower
Filter is securely in place and the Upper Filter Assembly is locked
into place. If the Upper Filter Assembly turns freely, it is not locked
into place.
Dishwasher Care
CLEANING THE DISHWASHER
Cleaning the Exterior
Clean the exterior of dishwasher with a soft, damp cloth and mild
detergent. If your dishwasher has a stainless steel exterior, a
stainless steel cleaner is recommended, such as affresh
®
Stainless
Steel Cleaner. Avoid using abrasive cleaning products on the
exterior of the dishwasher.
Cleaning the interior
Clean the interior of the dishwasher with a paste of powdered
dishwasher detergent and water or use liquid dishwasher detergent
on a damp sponge to clean the cooled-down interior.
A white vinegar rinse may remove white spots and film. Vinegar is
an acid and using it too often could damage your dishwasher.
Put 2 cups (500 mL) white vinegar in a glass or dishwasher-safe
measuring cup on the bottom rack. Run the dishwasher through a
complete washing cycle using an air-dry or an energy-saving dry
option. Do not use detergent. Vinegar will mix with the wash water.
Dishwasher maintenance procedure
Removal of Hard Water/Filming
Recommended use of a monthly maintenance product such as
affresh
®
Dishwasher Cleaner.
■ Place affresh
®
Dishwasher Cleaner tablet in main wash
compartment of detergent dispenser.
■ Select a normal cycle and start the dishwasher.
NOTE: Whirlpool recommends the use of premeasured detergent
tablets or packs and the use of rinse aid for regular daily use.
Drain air gap
To reduce risk of property damage during vacation or
extended time without use
■ When you will not be using the dishwasher during the summer
months, turn off the water and power supply to the dishwasher.
■ Make sure the water supply lines are protected against freezing
conditions. Ice formations in the supply lines can increase
water pressure and cause damage to your dishwasher or
home. Damage from freezing is not covered by the warranty.
■ When storing your dishwasher in the winter, avoid water
damage by having your dishwasher winterized by authorized
service personnel.
Filter Reinstallation Instructions
1. Noting the previous
illustrations, place the
Lower Filter under the
Locating Tabs in the
bottom of the dishwasher
so the round opening for
the Upper Filter Assembly
lines up with the round
opening in the bottom of
the tub.
2. Insert the Upper Filter
Assembly into the circular
opening in the Lower Filter.
To replace Upper Filter Assembly
L
O
C
K
U
N
L
O
C
K
P
U
S
H
D
O
W
N
&
T
U
R
N
3. Slowly rotate the filter clockwise until it drops into place.
Continue to rotate until the filter is locked into place. If the
filter is not fully seated (still turns freely), continue to turn
the filter clockwise until it drops and locks into place.
NOTE: The Upper Filter Assembly arrow does not have to
align with the arrow in the Lower Filter as long as the filter
is locked.
If you have a drain air
gap, check and clean
it if the dishwasher
isn't draining well.
13
Troubleshooting
First try the solutions suggested here. If you need further assistance or more recommendations that may help you avoid a service call,
refer to the warranty page in this manual and scan the code with your mobile device, or visit www.whirlpool.com/product_help.
In Canada, visit www.whirlpool.ca.
Contact us by mail with any questions or concerns at the address below:
In the U.S.A.:
Whirlpool Brand Home Appliances
Customer eXperience Center
553 Benson Road
Benton Harbor, MI 49022-2692
In Canada:
Whirlpool Brand Home Appliances
Customer eXperience Centre
200 – 6750 Century Ave.
Mississauga, Ontario L5N 0B7
Please include a daytime phone number in your correspondence.
PROBLEM SOLUTION
DISHWASHER DOES
NOT RUN
NOTE: It is normal for the dishwasher to repeatedly pause several times during a cycle.
If the Start/Resume light is blinking, close the door and push START/RESUME.
Be sure the door is closed and latched.
Be sure you have disabled Sleep mode by pressing either Start/Resume or Cancel, or opening
and closing the door before selecting your cycle/option.
Check that there is not an interference with large casserole dishes and the wash system at the back
of the dishwasher. Check to see if any items are protruding through the bottom or back of the rack. Also
check to see if tall items are hitting the upper rack or spray arm. Adjust loading as necessary to ensure
door is closed and latched.
Be sure you have selected a cycle. See “Cycle and Option Descriptions” section.
Be sure there is power to the dishwasher. A circuit breaker or fuse may have tripped.
If lights other than Start/Resume blink and the unit will not run, you will need to call for service.
DETERGENT REMAINS
IN THE DISPENSER OR
TABLET IS ON BOTTOM
OF TUB
Check for dishware such as cookie sheets, cutting boards, or large containers, etc., that may be
blocking the detergent dispenser from opening properly.
Be sure your detergent is fresh and lump free.
Be sure the cycle has completed (the Clean light is on). If it has not completed, you will need to
resume the cycle by closing the door and pressing Start/Resume.
CYCLE RUNS TOO LONG NOTES:
■ To use less water and reduce energy consumption, you will encounter cycles that typically run
for up to 3 hours.
■ A water heater setting of 120°F (49°C) is best. The dishwasher will delay longer while heating
cooler water.
■ Some options will add time to the cycle. See “Cycle and Option Descriptions” section. The Heat
Dry option adds approximately 45 minutes.
Try the 1 Hour Wash cycle.
Run the hot water at a faucet close to the dishwasher before starting the cycle.
DISHWASHER NOT DRYING NOTE: Plastic and items with nonstick surfaces are difficult to dry because they have a porous
surfaces which tend to collect water droplets. Towel drying may be necessary.
Use of rinse aid along with the Heat Dry option is needed for proper drying.
Proper loading of items can affect drying. (See specific loading instructions within this guide.)
Glasses and cups with concave bottoms hold water. This water may spill onto other items
when unloading.
■ Unload the bottom rack first.
■ Locate these items on the more slanted side of the rack for improved results.
WILL NOT FILL Be sure the water is turned on to the dishwasher.
Check that the overfill protection float is free from obstructions. See “Parts and Features” section.
Check for suds in the dishwasher. If foam or suds are detected, the dishwasher may not operate
properly or may not fill with water. See “Blinking Lights” in “Troubleshooting” section.
14
WATER REMAINS IN THE
TUB/WILL NOT DRAIN
Be sure the cycle has completed (the Clean indicator is on). If it has not, you will need to resume the
cycle by closing the door and pressing Start/Resume.
If dishwasher is connected to a food waste disposer, be sure the knockout plug has been removed
from the disposer inlet.
Check for kinks in the drain hose.
Check for food obstructions in the drain or disposer.
Check your house fuse or circuit breaker.
HARD WATER
(WHITE RESIDUE ON
DISHWASHER INTERIOR
OR GLASSWARE)
NOTE: Extremely hard water mineral deposits can cause damage to your dishwasher and make it
difficult to achieve good cleaning. A water softener is strongly recommended if your hardness is
15 grains or more. If a water softener is not installed, the following steps may help:
Use a commercial cleaner designed for dishwashers once per month.
Clean the upper and lower filters at least once per month. See “Cleaning Instructions” in the “Filtration
System” section.
Always use a rinse aid.
Always use a high-quality, fresh detergent.
Use a detergent booster/water softener additive designed for dishwashers.
ODORS NOTE: If the dishwasher is not used daily, you can run a rinse cycle with the partial load until a full load
is ready to run.
Run a vinegar rinse through the dishwasher by putting 2 cups (500 mL) of white vinegar in an upright
glass measuring cup in the lower rack. Run a normal cycle with the Heat Dry option turned off. Do not
use detergent.
The dishwasher may not be draining properly, see “Water Remains In The Tub/Will Not Drain” in the
“Troubleshooting” section.
NOISY NOTES:
■ Surging sounds can occur periodically throughout the cycle while the dishwasher is draining.
■ Normal water valve hissing may be heard periodically.
■ A normal snap sound may be heard when the detergent dispenser opens during the cycle and
when the door is opened at the end of the cycle.
■ Improper installation will affect noise levels.
Be sure the filters are properly installed.
A thumping sound may be heard if items extend beyond the racks and interfere with the wash arms.
Readjust the dishware and resume the cycle.
FOOD SOILS REMAIN
ON DISHES
Be sure the dishwasher is loaded correctly. Improper loading can greatly decrease the washing
performance. See “Dishwasher Use” section.
Check filter to ensure it is properly installed. Clean it if needed. See “Cleaning Instructions” in the
“Filtration System” section for details.
Select the proper cycle and option for the type of soils. The Sensor or Heavy cycle with the
Hi Temp Wash option can be used for tougher loads.
Be sure the incoming water temperature is at least 120°F (49°C).
Use the proper amount of fresh detergent. More detergent is needed for heavier soiled loads and hard
water conditions.
Scrape food from dishes prior to loading (do not prerinse).
DISHES DIRTY/SUDS IN
DISHWASHER/CYCLE
NOT COMPLETE
If foam or suds are detected by the dishwasher sensing system, the dishwasher may not operate
properly or may not fill with water.
Suds can come from:
■ Using the incorrect type of detergent, such as dish detergent for hand washing dishes, laundry
detergent, or hand soap.
■ Not replacing the rinse aid dispenser cap after filling (or refilling) the rinse aid.
■ Using an excessive amount of dishwasher detergent.
■ Inadequate rinsing off detergent from dishes washed by hand before loading them into
the dishwasher.
Call for service.
If no water was present in the machine at any time during a heated wash cycle, the cycle will end and
the Clean indicator will not come on. See “Will Not Fill” in the “Troubleshooting” section.
DID NOT SANITIZE If the sanitized light is blinking, the load is NOT sanitized. The cycle was interrupted in the final rinse
or the temperature for your water heater is set too low. Set your water heater to 120ºF (49°C).
DAMAGE TO DISHWARE Improper loading can cause dishes to become chipped or damaged. (See specific loading instructions
within this guide.)
PROBLEM SOLUTION
15
BLINKING LIGHTS Blinking indicators will occur when the cycle is paused or when the cycle has been interrupted by
opening the door. In this case, the Start/Resume button LED, the Cycle Status Indicator LED(s),
and the countdown bars on the Cycle Status Display all blink together to indicate that attention is
needed. See “Start or Resume a Cycle” in the “Dishwasher Use” section.
Blinking indicators can also occur when certain errors have been detected. In this case, the Clean
indicator will blink 4 times in a row with a pause in between each set of blinks. When this error occurs,
the controls will lock out and not allow another cycle to be started.
Call for service.
CLOUDY OR SPOTTED
DISHWARE (AND HARD
WATER SOLUTION)
NOTES:
■ Liquid rinse aid is necessary for drying and to reduce spotting.
■ Use the correct amount of detergent.
Confirm that the cloudiness is removable by soaking the item in white vinegar for 5 minutes. If the
cloudiness disappears, it is due to hard water. Adjust the amount of detergent and rinse aid. See “Hard
Water (White Residue On Dishwasher Interior Or Glassware)” in the “Troubleshooting” section. If it does
not come clear, it is due to etching (see below).
Be sure the incoming water temperature is set at 120°F (49°C).
Try using the High Temp Wash and Sani Rinse options.
To remove spotting, run a vinegar rinse through the dishwasher.
■ Wash and rinse the affected dishware and load into dishwasher. Remove all silverware and metal
items. Put 2 cups (500 mL) of white vinegar in a glass measuring cup in the lower rack. Run a normal
cycle with the Heat Dry option turned off. No detergent is needed.
ETCHING (PERMANENT
CLOUDINESS)
This is an erosion of the surface of the glassware and can be caused by a combination of: water that is
too hot, from using too much detergent with soft water, or by prewashing. Detergent needs food soil to
act upon. If etching has occurred, the glassware is permanently damaged. To avoid further etching,
adjust the detergent amount to match the water hardness, stop prewashing, and use water heating
options only when incoming water temperature is below 120°F (49°C).
LEAKING WATER Be sure dishwasher has been installed properly and is level.
Suds can cause the dishwasher to overflow. Measure the detergent accurately and use only detergents
designed for use in a dishwasher. Less detergent is needed in soft water. Try another brand of detergent
if sudsing continues.
To avoid rinse aid leaking from the dispenser, be sure the lid is securely attached and avoid overfilling.
TUB IS DISCOLORED NOTES:
■ High iron content in the water can discolor the tub.
■ Tomato-based foods can discolor the tub or dishware. Large amounts of tomato-based foods should
be removed from the dishes before loading.
■ A citrus-based cleaner can be used to clean.
PROBLEM SOLUTION
16
11/14
WHIRLPOOL
®
MAJOR APPLIANCE
LIMITED WARRANTY
ATTACH YOUR RECEIPT HERE. PROOF OF PURCHASE IS REQUIRED
TO OBTAIN WARRANTY SERVICE.
Please have the following information available when you call the
Customer eXperience Center:
■ Name, address and telephone number
■ Model number and serial number
■ A clear, detailed description of the problem
■ Proof of purchase including dealer or retailer name and address
IF YOU NEED SERVICE:
1. Before contacting us to arrange service, please determine whether your product requires repair. Some
questions can be addressed without service. Please take a few minutes to review the Troubleshooting or
Problem Solver section of the Use and Care Guide, scan the QR code on the right to access additional
resources, or visit www.whirlpool.com/product_help.
2. All warranty service is provided exclusively by our authorized Whirlpool Service Providers
. In the U.S. and
Canada, direct all requests for warranty service to:
Whirlpool Customer eXperience Center
In the U.S.A., call 1-800-253-1301. In Canada, call 1-800-807-6777.
If outside the 50 United States or Canada, contact your authorized Whirlpool dealer to determine whether another warranty applies.
ONE YEAR LIMITED WARRANTY
WHAT IS COVERED WHAT IS NOT COVERED
For one year from the date of purchase, when this major
appliance is installed, operated and maintained according to
instructions attached to or furnished with the product,
Whirlpool Corporation or Whirlpool Canada LP (hereafter
“Whirlpool”) will pay for Factory Specified Replacement Parts
and repair labor to correct defects in materials or
workmanship that existed when this major appliance was
purchased, or at its sole discretion replace the product. In the
event of product replacement, your appliance will be
warranted for the remaining term of the original unit's
warranty period.
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS
LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS
PROVIDED HEREIN. Service must be provided by a
Whirlpool designated service company. This limited warranty
is valid only in the United States or Canada and applies only
when the major appliance is used in the country in which it
was purchased. This limited warranty is effective from the
date of original consumer purchase. Proof of original
purchase date is required to obtain service under this limited
warranty.
1. Commercial, non-residential, multiple-family use, or use inconsistent with published user,
operator or installation instructions.
2. In-home instruction on how to use your product.
3. Service to correct improper product maintenance or installation, installation not in accordance
with electrical or plumbing codes or correction of household electrical or plumbing (i.e. house
wiring, fuses or water inlet hoses).
4. Consumable parts (i.e. light bulbs, batteries, air or water filters, preservation solutions, etc.).
5. Defects or damage caused by the use of non-genuine Whirlpool parts or accessories.
6. Conversion of products from natural gas or L.P. gas.
7. Damage from accident, misuse, abuse, fire, floods, acts of God or use with products not
approved by Whirlpool.
8. Repairs to parts or systems to correct product damage or defects caused by unauthorized
service, alteration or modification of the appliance.
9. Cosmetic damage including scratches, dents, chips, and other damage to the appliance
finishes unless such damage results from defects in materials and workmanship and is
reported to Whirlpool within 30 days.
10. Discoloration, rust or oxidation of surfaces resulting from caustic or corrosive environments
including but not limited to high salt concentrations, high moisture or humidity or exposure to
chemicals.
11. Food or medicine loss due to product failure.
12. Pick-up or delivery. This product is intended for in-home repair.
13. Travel or transportation expenses for service in remote locations where an authorized
Whirlpool servicer is not available.
14. Removal or reinstallation of inaccessible appliances or built-in fixtures (i.e. trim, decorative
panels, flooring, cabinetry, islands, countertops, drywall, etc.) that interfere with servicing,
removal or replacement of the product.
15. Service or parts for appliances with original model/serial numbers removed, altered or not
easily determined.
The cost of repair or replacement under these excluded circumstances shall be borne by the
customer.
DISCLAIMER OF IMPLIED WARRANTIES
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A
PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do not allow
limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This warranty gives you
specific legal rights, and you also may have other rights that vary from state to state or province to province.
DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY
Whirlpool makes no representations about the quality, durability, or need for service or repair of this major appliance other than the representations
contained in this warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes with this major appliance, you
should ask Whirlpool or your retailer about buying an extended warranty.
LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. WHIRLPOOL
SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the exclusion or limitation of
incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives you specific legal rights, and
you also may have other rights that vary from state to state or province to province.
www.whirlpool.com/product_help
W10852541A
®
/™ © 2016 Whirlpool. All rights reserved. 2/16
17
LE AGRADECEMOS la compra de este producto de alta calidad. Si usted experimenta un problema que no esté cubierto en
SOLUCIÓN DE PROBLEMAS, visite nuestro sitio de Internet en www.whirlpool.com para obtener información adicional. Si
considera que aún necesita ayuda, llámenos al 1-800-253-1301. En Canadá, visite nuestro sitio de Internet en www.whirlpool.ca
o llámenos al 1-800-807-6777.
Necesitará tener a mano el número de modelo y de serie, que está ubicado cerca de la puerta del lado derecho o izquierdo del
interior de la lavavajillas.
Seguridad de la lavavajillas
INSTRUCCIONES PARA EL
USUARIO DE LA LAVAVAJILLAS
ÍNDICE
SEGURIDAD DE LA LAVAVAJILLAS......................................17
QUÉ HAY DE NUEVO EN SU LAVAVAJILLAS.......................19
ENERGÍA...................................................................................19
RENDIMIENTO ........................................................................19
PIEZAS Y CARACTERÍSTICAS...............................................20
PASOS RÁPIDOS.....................................................................21
USO DE LA LAVAVAJILLAS....................................................22
DESCRIPCIÓN DE CICLOS Y OPCIONES.............................25
CARACTERÍSTICAS DE LA LAVAVAJILLAS.........................27
SISTEMA DE FILTRACIÓN......................................................28
CUIDADO DE LA LAVAVAJILLAS...........................................29
SOLUCIÓN DE PROBLEMAS .................................................30
GARANTÍA ................................................................................33
Si no sigue las instrucciones de inmediato, usted puede
morir o sufrir una lesión grave.
Si no sigue las instrucciones, usted puede morir o sufrir
una lesión grave.
Todos los mensajes de seguridad le dirán el peligro potencial, le dirán cómo reducir las posibilidades de sufrir una lesión y lo que
puede suceder si no se siguen las instrucciones.
Su seguridad y la seguridad de los demás es muy importante.
Hemos incluido muchos mensajes importantes de seguridad en este manual y en su electrodoméstico. Lea y obedezca siempre
todos los mensajes de seguridad.
ADVERTENCIA
PELIGRO
Este es el símbolo de alerta de seguridad.
Este símbolo le llama la atención sobre peligros potenciales que pueden ocasionar la muerte o una lesión a
usted y a los demás.
Todos los mensajes de seguridad irán a continuación del símbolo de advertencia de seguridad y de la palabra
“PELIGRO” o “ADVERTENCIA”. Estas palabras significan:
18
INSTRUCCIONES IMPORTANTES DE SEGURIDAD
ADVERTENCIA:
Cuando use la lavavajillas siga precauciones básicas, incluyendo las siguientes:
GUARDE ESTAS INSTRUCCIONES
■
Lea todas las instrucciones antes de usar la lavavajillas.
■
Use la lavavajillas únicamente para las funciones que fue
diseñada.
■
Use únicamente detergentes o agentes de enjuague
recomendados para ser usados en las lavavajillas y
manténgalos fuera del alcance de los niños.
■
Al introducir los artículos para lavar:
1) Coloque los artículos puntiagudos de manera que no
dañen el sello de la puerta
2) Introduzca los cuchillos filosos con los mangos hacia
arriba para reducir el riesgo de cortaduras.
■
No lave artículos de plástico que no lleven la indicación
“lavables en la lavavajillas” u otra similar. Lea las
recomendaciones del fabricante para los artículos de
plástico que no lleven tal indicación.
■
No toque el elemento de calefacción durante o
inmediatamente después de usar la lavavajillas.
■
No haga funcionar la lavavajillas a menos que todos los
paneles estén colocados debidamente en su lugar.
■
No juegue con los controles.
■
No abuse, ni se siente ni se pare sobre la puerta, la tapa o
sobre las canastas de la lavavajillas.
■
Para reducir el riesgo de lesión, no permita que los niños
jueguen dentro ni sobre la lavavajillas.
■
Bajo ciertas condiciones, un sistema de agua caliente que
no ha sido usado por dos semanas o más puede producir
gas hidrógeno. EL GAS HIDRÓGENO ES EXPLOSIVO. Si
el sistema de agua caliente no ha sido usado por ese
período, abra todas las llaves de agua caliente y deje que
corra el agua por varios minutos antes de usar la
lavavajillas. Esto permitirá que los gases acumulados
escapen. Debido a que el gas es inflamable, no fume ni
encienda ninguna llama abierta durante este tiempo.
■
Quite la puerta o la tapa del compartimiento de lavado
cuando remueva o deje de usar para siempre una vieja
lavavajillas.
INSTRUCCIONES DE CONEXIÓN A TIERRA
GUARDE ESTAS INSTRUCCIONES
■
Para una lavavajillas con cable eléctrico y conexión a
tierra:
La lavavajillas debe estar conectada a tierra. En caso de
funcionamiento defectuoso o avería, la conexión a tierra
reduce el riesgo de choque eléctrico al establecer una ruta
de menor resistencia para la corriente eléctrica. La
lavavajillas viene equipada con un cable eléctrico que tiene
un conductor para conexión a tierra y un enchufe con
conexión a tierra. El enchufe debe ser conectado a un
contacto apropiado que esté instalado y conectado a tierra
de acuerdo con todos los códigos y ordenanzas locales.
ADVERTENCIA: La conexión inadecuada del
conductor de conexión a tierra puede resultar en riesgo
de choque eléctrico. Pregunte a un electricista
calificado o a un agente de servicio si no está seguro si
la lavavajillas está adecuadamente conectada a tierra.
No modifique el enchufe que viene con la lavavajillas. Si
no cabe en el contacto, pida que un electricista
calificado instale un contacto apropiado.
■
Para lavavajillas con conexión permanente:
Esta lavavajillas debe estar conectada a un sistema de
cableado de metal permanente, conectado a tierra, o se
debe tender un conducto para la conexión a tierra del
equipo con los conductores de circuito y conectado a la
terminal de tierra del equipo o al conductor de
suministro de la lavavajillas.
Peligro de Vuelco
No use la lavavajillas antes de estar completamente instalada.
No se apoye en la puerta abierta.
No seguir estas instrucciones puede ocasionar heridas serias o cortaduras.
ADVERTENCIA
19
QUÉ HAY DE NUEVO EN SU LAVAVAJILLAS
Energía
Rendimiento
¡Felicitaciones por haber comprado la lavavajillas con bajo consumo de agua y energía! Esta lavavajillas limpia
rociando la vajilla con agua y hace pausas para permitir que el detergente remoje la vajilla y afloje la suciedad de
los platos. Para obtener una limpieza excepcional, los ciclos se hacen más largos debido al remojo y las pausas.
Varios modelos tienen un sensor óptico de agua. El sensor óptico de agua se usa para determinar el consumo
óptimo de agua y energía para un desempeño de limpieza ideal. Las lavavajillas eficaces funcionan por más tiempo
para ahorrar agua y energía, de la misma manera que se ahorra gasolina cuando se conduce un automóvil más
despacio. El primer ciclo con sensor durará más tiempo para calibrar el sensor óptico.
Agente de enjuague
El uso del agente de enjuague hará óptimo el desempeño de
lavado y secado. Esta lavavajillas ha sido diseñada
específicamente para usarse en conjunto con agente de
enjuague, para obtener un mejor desempeño de secado y
controlar la acumulación de depósitos de agua dura. Las
lavavajillas con bajo consumo de energía usan menos agua y
energía, de modo que dependen de la acción de desplazamiento
del agua por obra del agente de enjuague para asegurar un
óptimo desempeño.
Detergente
Estados Unidos y Canadá han aprobado una restricción que
limita la cantidad de fósforo (fosfatos) en los detergentes para
lavavajillas domésticas a no más de 0,5%, mientras que los
detergentes previos contenían 8,7%. Los principales fabricantes
han reformulado su detergente para lavavajillas de acuerdo a
este cambio, un paso más en la conciencia ecológica. Con estos
cambios, se recomienda usar pastillas y paquetes de calidad por
practicidad y para mejorar el rendimiento.
Sistema de filtración
Su lavavajillas cuenta con lo último en tecnología de filtración
para lavavajillas. El sistema de filtración triple minimiza los
sonidos y optimiza el ahorro de agua y energía mientras
proporciona una limpieza óptima. El mantenimiento periódico de
los filtros hará posible un rendimiento superior de limpieza. Le
sugerimos limpiar el filtro superior e inferior y enjuagarlos bajo
agua del grifo por lo menos una vez al mes.
SLIDE
SLID
E
P
U
S
H
D
O
W
N
&
T
U
R
N
L
O
C
K
U
N
L
O
C
K
20
Piezas y características
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
Whirlpool WDF560SAFT Le manuel du propriétaire
- Catégorie
- Lave-vaisselle
- Taper
- Le manuel du propriétaire