LG 75NANO95UNA Le manuel du propriétaire

65NANO95UNA

65NANO97UNA

65NANO99UNA

75NANO95UNA

75NANO97UNA

75NANO99UNA

www.lg.com

Printed in Korea

LED TV*

Safety and Reference

OWNER’S MANUAL

Please read this manual carefully before operating

your set and retain it for future reference.

* LG LED TV applies LCD screen with LED backlights.

*MFL71500633*

(2006-REV01)

2

ENGLISH_index

Important Safety Instruction

• Read these instructions.

• Keep these instructions.

• Heed all warnings.

• Follow all instructions.

• Do not use this apparatus near water.

• Clean only with dry cloth.

• Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

• Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A

grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided

plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

• Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the

apparatus.

• Only use attachments/accessories specified by the manufacturer.

• Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution

when moving the cart/apparatus combination to avoid injury from tip-over.

• Unplug this apparatus during lightning storms or when unused for long periods of time.

• Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply

cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture,

does not operate normally, or has been dropped.

By using this product, you agree that all disputes between you and LG arising out of or relating in any way to this product (including but not limited

to warranty disputes) shall be resolved exclusively through binding arbitration on an individual basis. The terms of the arbitration agreement

(including details on the procedure for resolving disputes) is available at www.lg.com/us/arbitration (USA) or www.lg.com/ca_en/arbitration

(Canada).

3

ENGLISH_index

Warning! Safety

instructions

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT

REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.

REFER TO QUALIFIED SERVICE PERSONNEL.

The symbol is intended to alert the user to the presence of

uninsulated dangerous voltage within the product’s

enclosure that may be of sufficient magnitude to constitute a risk

of electric shock to persons.

The symbol is intended to alert the user to the presence of

important operating and maintenance (servicing)

instructions in the literature accompanying the device.

WARNING: TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO

NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

• TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR OTHER ITEMS

WITH OPEN FLAMES AWAY FROM THIS PRODUCT AT ALL TIMES.

• Do not place the TV and/or remote control in the following

environments:

- Keep the product away from direct sunlight.

- An area with high humidity such as a bathroom

- Near any heat source such as stoves and other devices that

produce heat.

- Near kitchen counters or humidifiers where they can easily be

exposed to steam or oil.

- An area exposed to rain or wind.

- Do not expose to dripping or splashing and do not place objects

filled with liquids, such as vases, cups, etc. on or over the

apparatus (e.g., on shelves above the unit).

- Near flammable objects such as gasoline or candles, or expose

the TV to direct air conditioning.

- Do not install in excessively dusty places.

Otherwise, this may result in fire, electric shock, combustion/

explosion, malfunction or product deformation.

• Ventilation

- Install your TV where there is proper ventilation. Do not install in

a confined space such as a bookcase.

- Do not install the product on a carpet or cushion.

- Do not block or cover the product with cloth or other materials

while unit is plugged in.

• Take care not to touch the ventilation openings. When watching

the TV for a long period, the ventilation openings may become hot.

• Protect the power cord from physical or mechanical abuse, such as

being twisted, kinked, pinched, closed in a door, or walked upon.

Pay particular attention to plugs, wall outlets, and the point where

the cord exits the device.

• Do not move the TV whilst the Power cord is plugged in.

• Do not use a damaged or loosely fitting power cord.

• Be sure to grasp the plug when unplugging the power cord. Do not

pull on the power cord to unplug the TV.

• Do not connect too many devices to the same AC power outlet as

this could result in fire or electric shock.

• Disconnecting the Device from the Main Power

- The power plug is the disconnecting device. In case of an

emergency, the power plug must remain readily accessible.

• Do not let your children climb or cling onto the TV. Otherwise, the

TV may fall over, which may cause serious injury.

• Outdoor Antenna Grounding (Can differ by country):

- If an outdoor antenna is installed, follow the precautions below.

An outdoor antenna system should not be located in the vicinity

of overhead power lines or other electric light or power circuits,

or where it can come in contact with such power lines or circuits

as death or serious injury can occur.

Be sure the antenna system is grounded to provide some

protection against voltage surges and built-up static charges.

Section 810 of the National Electrical Code (NEC) in the U.S.A.

provides information with respect to proper grounding of the

mast and supporting structure, grounding of the lead-in wire

to an antenna discharge unit, size of grounding conductors,

location of antenna discharge unit, connection to grounding

electrodes and requirements for the grounding electrode.

Antenna grounding according to the National Electrical Code,

ANSI/NFPA 70

4

ENGLISH_index

• Grounding (Except for devices which are not grounded.)

- TV with a three-prong grounded AC plug must be connected to

a three-prong grounded AC outlet. Ensure that you connect the

earth ground wire to prevent possible electric shock.

• Never touch this apparatus or antenna during a lightning storm.

You may be electrocuted.

• Make sure the power cord is connected securely to the TV and wall

socket if not secured damage to the Plug and socket may occur and

in extreme cases a fire may break out.

• Do not insert metallic or inflammable objects into the product. If a

foreign object is dropped into the product, unplug the power cord

and contact the customer service.

• Do not touch the end of the power cord while it is plugged in. You

may be electrocuted.

• If any of the following occur, unplug the product

immediately and contact your local customer service.

- The product has been damaged.

- If water or another substance enters the product (like an AC

adapter, power cord, or TV).

- If you smell smoke or other odors coming from the TV

- When lightning storms or when unused for long periods of time.

Even the TV is turned off by remote control or button, AC power

source is connected to the unit if not unplugged in.

• Do not use high voltage electrical equipment near the TV (e.g., a

bug zapper). This may result in product malfunction.

• Do not attempt to modify this product in any way without written

authorization from LG Electronics. Accidental fire or electric shock

can occur. Contact your local customer service for service or repair.

Unauthorized modification could void the user’s authority to

operate this product.

• Use only an authorized attachments / accessories approved by

LG Electronics. Otherwise, this may result in fire, electric shock,

malfunction, or product damage.

• Never disassemble the AC adapter or power cord. This may result in

fire or electric shock.

• Handle the adapter carefully to avoid dropping or striking it. An

impact could damage the adapter.

• To reduce the risk of fire or electrical shock, do not touch the TV

with wet hands. If the power cord prongs are wet or covered with

dust, dry the power plug completely or wipe dust off.

• Batteries

- Store the accessories (battery, etc.) in a safe location out of the

reach of children.

- Do not short circuit, disassemble, or allow the batteries to

overheat. Do not dispose of batteries in a fire. Batteries should

not be exposed to excessive heat.

- Caution: Risk of fire or explosion if the battery is replaced by an

incorrect type.

• Moving

- When moving, make sure the product is turned off, unplugged,

and all cables have been removed. It may take 2 or more people

to carry larger TVs. Do not press or put stress on the front panel

of the TV. Otherwise, this may result in product damage, fire

hazard or injury.

• Keep the packing anti-moisture material or vinyl packing out of the

reach of children.

• Do not allow an impact shock, any objects to fall into the product,

and do not drop anything onto the screen.

• Do not press strongly upon the panel with a hand or a sharp

object such as a nail, pencil, or pen, or make a scratch on it. It may

causedamage to screen.

• Cleaning

- When cleaning, unplug the power cord and wipe gently with a

soft/dry cloth. Do not spray water or other liquids directly on the

TV. Do not clean your TV with chemicals including glass cleaner,

any type of air freshener, insecticide, lubricants, wax (car,

industrial), abrasive, thinner, benzene, alcohol etc., which can

damage the product and/or its panel. Otherwise, this may result

in electric shock or product damage.

5

ENGLISH_index

Preparing

• When the TV is turned on for the first time after being shipped

from the factory, initialization of the TV may take approximately

one minute.

• Image shown may differ from your TV.

• Your TV’s OSD (On Screen Display) may differ slightly from that

shown in this manual.

• The available menus and options may differ from the input source

or product model that you are using.

• New features may be added to this TV in the future.

• The device must be easily accessed to a location outlet near the

access. Some devices are not made by turning on / off button,

turning off the device and unplugging the power cord.

• The items supplied with your product may vary depending upon

the model.

• Product specifications or contents of this manual may be changed

without prior notice due to upgrade of product functions.

• For an optimal connection, HDMI cables and USB devices should

have bezels less than 8mm (0.31inches) thick, 18mm (0.7inches)

width and 8mm (0.31inches) a wire diameter. (Depending upon

model)

• Use an extension cable that supports if the USB cable or

USB flash drive does not fit into your TV’s USB port.

A

B

C

A

B

* A

<

=

8mm (0.31inches)

* B

<

=

18mm (0.7inches)

* C

<

=

8mm (0.31inches)

• Use a certified cable with the HDMI logo attached. If you do not use

a certified HDMI cable, the screen may not display or a connection

error may occur.

• Recommended HDMI cable types (3m (9.84feet) or less)

- Ultra High Speed HDMI

®

/™ cable

Optional Extras

Optional extras can be changed or modified for quality improvement

without any notification. Contact your dealer for buying these items.

These devices work only with certain models. The model name or

design may be changed due to the manufacturer’s circumstances or

policies.

Magic Remote Control

MR20GA

Check whether your TV model supports Bluetooth in the Wireless

Module Specification to verify whether it can be used with the Magic

Remote.

Wall Mounting Bracket

(Depending upon model)

Make sure to use screws and wall mount bracket that meet the VESA

standard. Standard dimensions for the wall mount kits are described in

the following table.

A

Model 65/75NANO99*

Screws distance (A) (mm) 180

Standard screw M6

Number of screws 2

Wall mount bracket

WB20GB

A

B

Model

65NANO95*

65NANO97*

65/75NANO99*

75NANO95*

75NANO97*

VESA (A x B) (mm) 400x400 600x400

Standard screw M6 M8

Number of screws 4 4

Wall mount bracket LSW440B LSW640B

6

ENGLISH_index

Lifting and moving the TV

When moving or lifting the TV, read the following to prevent the TV

from being scratched or damaged and for safe transportation regardless

of its type and size.

• It is recommended to move the TV in the box or packing material

that the TV originally came in.

• Before moving or lifting the TV, disconnect the power cord and all

cables.

• When holding the TV, the screen should face away from you to

avoid damage.

• Hold the top and bottom of the TV frame firmly. Make sure not to

hold the transparent part, speaker, or speaker grille area.

• Use at least two people to move a large TV.

• When transporting the TV by hand, hold the TV as shown in the

following illustration.

• When transporting the TV, do not expose the TV to jolts or excessive

vibration.

• When transporting the TV, keep the TV upright; never turn the TV

on its side or tilt towards the left or right.

• When handling the TV, be careful not to damage the protruding

buttons.

• Avoid touching the screen at all times, as this may result in

damage to the screen.

• Do not place the product on the floor with its front facing

down without padding. Failure to do so may result in

damage to the screen.

• When attaching the stand to the TV set, place the screen

facing down on a cushioned table or flat surface to protect

the screen from scratches.

Mounting on the Table

1 Lift and tilt the TV into its upright position on a table.

• Leave a minimum of 10 cm (4 inches) space from the wall for

proper ventilation.

10cm

(4inches)

10cm

(Depending upon model)

2 Connect the power cord to a wall outlet.

• Do not apply foreign substances (oils, lubricants, etc.) to

the screw parts when assembling the product. (Doing so

may damage the product.)

• If you install the TV on a stand, you need to take actions

to prevent the product from overturning. Otherwise, the

product may fall over, which may cause injury.

• Do not use any unapproved items to ensure the safety and

lifespan of the product.

• Any damages or injuries by using unapproved items are not

covered by the warranty.

• Make sure that the screws are fastened tightly. (If they are

not fastened securely enough, the TV may tilt forward after

being installed.)

• Do not fasten the screws with excessive force otherwise

they may strip and become loose.

7

ENGLISH_index

Securing TV to the Wall

(Depending upon model)

1 Insert and tighten the eye-bolts or TV brackets and bolts on the back

of the TV.

• If there are bolts inserted at the eye-bolts position, remove the

bolts first.

2 Mount the wall brackets with the bolts to the wall. Match the

location of the wall bracket and the eye-bolts on the rear of the TV.

3 Connect the eye-bolts and wall brackets tightly with a sturdy rope or

cable. Make sure to keep the rope parallel to the flat surface.

• Use a platform or cabinet that is strong and large enough to

support the TV securely.

• Brackets, bolts, and ropes are optional. You can obtain additional

accessories from your local dealer.

Mounting to the Wall

An optional wall mount can be used with your LG Television. Consult

with your local dealer for a wall mount that supports the VESA

standard used by your TV model. Carefully attach the wall mount

bracket at the rear of the TV. Install the wall mount bracket on a solid

wall perpendicular to the floor. If you are attaching the TV to other

building materials, please contact qualified personnel to install the

wall mount. Detailed instructions will be included with the wall mount.

We recommend that you use an LG brand wall mount. The LG wall

mount is easy to adjust or to connect the cables. When you do not use

LG’s wall mount bracket, use a wall mount bracket where the device is

adequately secured to the wall with enough space to allow connectivity

to external devices. If you are using a non-adjustable mount, attach the

mount to the wall. Attach the cables to the TV first, then attach the TV

to the mount.

10cm

10cm (4inches)

10cm

(Depending upon model)

• Remove the stand before installing the TV on a wall mount

by performing the stand attachment in reverse.

• For more information of screws and wall mount bracket,

refer to the Separate Purchase.

• If you intend to mount the product to a wall, attach VESA

standard mounting interface (optional parts) to the back

of the product. When you install the set to use the wall

mounting bracket (optional parts), fix it carefully so as

not to drop.

• When mounting a TV on the wall, make sure not to install

the TV by hanging the power and signal cables on the back

of the TV.

• Do not install this product on a wall if it could be exposed

to oil or oil mist. This may damage the product and cause

it to fall.

8

ENGLISH_index

• When installing the wall mounting bracket, it is recommended to

cover the stand hole using tape, in order to prevent the influx of

dust and insects, (Depending upon model).

Stand hole

Connections

You can connect various external devices to the TV. For more

information on external device’s connection, refer to the manual

provided with each device.

• Certain 8K input/decoding standards may not be supported.

An additional device may be necessary to support certain 8K

standards. Upscaled and enhanced 8K images will vary depending

upon the source content.

Antenna/Cable

Connect an antenna, cable, or cable box to watch TV while referring to

the following. The illustrations may differ from the actual items and an

RF cable is optional.

• Make sure not to bend the copper wire of the RF cable.

Copper wire

• Complete all connections between devices, and then connect the

power cord to the power outlet to prevent damage to your TV.

• Use a signal splitter to use 2 TVs or more.

• DTV Audio Supported Codec: MPEG, Dolby Digital

• This TV cannot receive Ultra HD (3840 x 2160 pixels) broadcasts

directly because the related standards have not been confirmed.

Other connections

Connect your TV to external devices. For the best picture and audio

quality, connect the external device and the TV with the HDMI cable.

HDMI

• When connecting the HDMI cable, the product and external devices

should be turned off and unplugged.

• Supported HDMI Audio format (Depending upon model):

True HD (48kHz),

Dolby Digital / Dolby Digital Plus (32kHz / 44.1kHz / 48kHz),

PCM (32kHz / 44.1kHz / 48kHz / 96kHz / 192kHz)

9

ENGLISH_index

• → → [Picture] → [Additional Settings] → [HDMI Ultra

HD Deep Color]

- 8K: Support 8K @ 50/60Hz (4:2:0), 8K @ 24/25/30Hz (4:4:4,

4:2:2, 4:2:0)

- 4K: Support 4K @ 50/60Hz (4:4:4, 4:2:2, 4:2:0), 4K @ 100/120Hz

(4:4:4, 4:2:2, 4:2:0)

- Off: Support 4K @ 50/60Hz (4:2:0)

If the device connected to Input Port also supports Ultra HD Deep

Color, your picture may be clearer. However, if the device doesn’t

support it, it may not work properly. In that case, change the TV’s

[HDMI Ultra HD Deep Color] setting to off.

- This feature is available only on certain models which support

HDMI Ultra HD Deep Color.

IR Blaster

• Control the set-top box (cable/satellite/IP/OTT), Blu-ray/DVD

player, soundbar, game consoles, etc., using the IR Blaster.

(Depending upon country)

- Connect the IR Blaster cable to the TV’s IR Blaster port.

- Place both ends (one or two) of the IR Blaster in front of the

external device as shown in the picture below.

- Use universal control settings to control the device. Go to

→ → [Connection] → [Device Connection Settings] →

[Universal Control Settings].

- Secure the IR Blaster with the 3M tape provided.

External Devices

Supported external devices are: Blu-ray player, HD receivers, DVD

players, VCRs, audio systems, USB storage devices, PC, gaming devices,

and other external devices. For more information on external device’s

connection, refer to the manual provided with each device.

• If you record a TV program on a Blu-ray/DVD recorder or VCR, make

sure to connect the TV signal input cable to the TV through a DVD

recorder or VCR. For more information about recording, refer to the

manual provided with the connected device.

• The external device connections shown may differ slightly from

illustrations in a manual.

• Connect external devices to the TV regardless about the order of

the TV port.

• If you connect a gaming device to the TV, use the cable supplied

with the gaming device.

• Refer to the external equipment’s manual for operating

instructions.

• In PC mode, there may be noise associated with the resolution,

vertical pattern, contrast or brightness. If noise is present, change

the PC output to another resolution, change the refresh rate to

another rate or adjust the brightness and contrast on the [Picture]

menu until the picture is clear. Depending upon the graphics card,

some resolution settings may not allow the image to be positioned

on the screen properly.

• Some USB Hubs may not work. If a USB device connected through

a USB Hub is not detected, connect it directly to the USB port on

the TV.

• When connecting via a wired LAN, it is recommended to use a CAT

7 cable.

• The TV may be capable of operating without a set-top-box from a

multichannel video programming distributor (MVPD).

10

ENGLISH_index

Remote RS-232C setup

To obtain the RS-232C external control setup information, please

visit ww w.lg.com. Download and read the manual, (Depending upon

model).

• Do not drop the product or let it fall over when connecting

external devices. Otherwise, this may result in injury or

damage to the product.

• When connecting external devices such as video game

consoles, make sure the connecting cables are long

enough. Otherwise, the product may fall over, which may

cause injury or damage the product.

Using Button

You can simply operate the TV functions, using the button.

Basic functions

Power On (Press)

Power Off

1

(Press and Hold)

Menu Control (Press

2

)

Menu Selection (Press and Hold

3

)

1 All running apps will close.

2 You can access and adjust the menu by pressing the button when

TV is on.

3 You can use the function when you access menu control.

Adjusting the menu

When the TV is turned on, press the button one time. You can adjust

the Menu items using the button.

Turns the power off.

Changes the input source.

Adjusts the volume level.

Scrolls through the saved channels.

11

ENGLISH_index

Using Magic Remote

Control

(Depending upon model)

The descriptions in this manual are based on the buttons on the remote

control. Please read this manual carefully and use the TV correctly.

When the message [Magic Remote battery is low. Please change the

battery.] is displayed, replace the batteries.

To install batteries, open the battery cover, replace batteries (1.5VAA)

matching the and ends to the label inside the compartment,

and close the battery cover. Be sure to point the magic remote toward

the remote control sensor on the TV. To remove the batteries, perform

the installation actions in reverse. This remote uses infrared light. When

in use, it should be pointed in the direction of the TV’s remote sensor.

1 1

1

(Some buttons and services may not be provided depending upon

models or regions.)

To use the button, press and hold for more than 1 second.

(POWER) Turns the TV on or off.

(STB POWER) You can turn your set-top box on or off by adding

the settop box to the universal remote control for your TV.

Number buttons Enters numbers.

Accesses the [Quick Help].

(DASH) Inserts a between numbers such as 2-1 and 2-2.

Accesses the saved channel list.

(MORE ACTIONS) Displays more remote control functions.

Edits QUICK ACCESS

- QUICK ACCESS is a feature that allows you to enter a specified app

or Live TV directly by pressing and holding the number buttons.

SAP (Secondary Audio Program) feature can also be

enabled by pressing the button.

Adjusts the volume level.

(MUTE) Mutes all sounds.

(MUTE) Accesses the [Accessibility] menu.

Scrolls through the saved channels.

(Voice recognition) Network connection is required to use the

voice recognition function.

Check for recommended content. (Some recommended services may

not be available in some countries.)

(Voice recognition) Speak while pressing and holding the

button to use the voice recognition feature.

(HOME) Accesses the Home menu.

(HOME) Shows the previous history.

(Q. Settings) Accesses the Quick Settings.

(Q. Settings) Displays the [All Settings] menu.

Wheel (OK) Press the center of button to select a menu. You

can change channels by using button.

(up/down/left/right) Press the up, down, left or right

button to scroll the menu. If you press buttons while

the pointer is in use, the pointer will disappear from the screen and

Magic Remote will operate like a general remote control. To display

the pointer on the screen again, shake Magic Remote to the left and

right.

(BACK) Returns to the previous level.

(BACK) Clears on-screen displays and returns to last input

viewing.

Displays the program event according to time scheduler.

1

Streaming Service buttons Connects to the Video Streaming

Service.

(INPUT) Changes the input source.

(INPUT) Accesses the [Home Dashboard].

, , , These access special functions in some

menus.

, (Control buttons) Controls media contents.

12

ENGLISH_index

Registering Magic Remote Control

How to register the Magic Remote Control

To use the Magic Remote, first pair it with your TV.

1 Put batteries into the Magic Remote and turn the TV on.

2 Point the Magic Remote at your TV and press the Wheel (OK)

on the remote control.

* If the TV fails to register the Magic Remote, try again after turning the

TV off and back on.

How to deregister the Magic Remote

Control

Press the (BACK) and (HOME) buttons at the same time, for

five seconds, to unpair the Magic Remote with your TV.

* Press and hold the button for more than 5 seconds to

disconnect and re-register the Magic Remote at the same time.

• Do not mix new batteries with old batteries. This may

cause the batteries to overheat and leak.

• Failure to match the correct polarities of the battery may

cause the battery to burst or leak, resulting in fire, personal

injury, or ambient pollution.

• This apparatus uses batteries. In your community there

might be regulations that require you to dispose of these

batteries properly due to environmental considerations.

Please contact your local authorities for disposal or

recycling information.

• Batteries inside or inside the product shall not be exposed

to excessive heat such as sunshine, fire or the like.

User Guide

For more information about this TV, read the USER GUIDE embedded in

the product. (Depending upon model)

• To open the USER GUIDE → → [Support] → [User

Guide]

Troubleshooting

Cannot control the TV with the remote control.

• Check if anything such as tape has been placed over the receiver.

• Check if there is any obstacle between the product and the remote

control.

• Replace the batteries with new fresh ones.

No image display and no sound is produced.

• Check if the product is turned on.

• Check if the power cord is connected to a wall outlet.

• Check if there is a problem in the wall outlet by connecting other

products.

The TV turns off suddenly.

• Check the power control settings. The power supply may be

interrupted.

• Check if the auto-off function is activated in the settings menu.

• If there is no signal while the TV is on, the TV will turn off

automatically after 15 minutes of inactivity.

13

ENGLISH_index

Abnormal Display

• If the TV feels cold to the touch, there may be a small flicker when

it is turned on. This is normal; there is nothing wrong with TV.

Some minute dot defects may be visible on the screen, appearing

as tiny red, green, or blue spots. However, they have no adverse

effect on the TV’s performance. Avoid touching the LCD screen or

holding your finger(s) against it for long periods of time. Doing so

may produce some temporary distortion effects on the screen.

• This panel is an advanced product that contains millions of pixels.

In a very few cases, you could see fine dots on the screen while

you’re viewing the TV. Those dots are deactivated pixels and do not

affect the performance and reliability of the TV.

• Displaying a still image for a prolonged period of time may cause

an image sticking. Avoid displaying a fixed image on the TV screen

for a extended length of time.

Generated Sound

• Cracking noise A cracking noise that occurs when watching or

turning off the TV is generated by plastic thermal contraction due

to temperature and humidity. This noise is common for products

where thermal deformation is required.

• Electrical circuit humming/panel buzzing A low level noise is

generated from a high-speed switching circuit, which supplies a

large amount of current to operate a product. It varies depending

upon the product. This generated sound does not affect the

performance and reliability of the product.

• When cleaning the product, be careful not to allow any

liquid or foreign objects to enter the gap between the

upper, left or right side of the panel and the guide panel,

(Depending upon model).

• Make sure to wring any excess water or cleaner from the

cloth.

• Do not spray water or cleaner directly onto the TV screen.

• Make sure to spray just enough of water or cleaner onto a

dry cloth to wipe the screen.

14

ENGLISH_index

Specifications

Product specifications may be changed without prior notice due to upgrade of product functions.

Estimated yearly energy consumption indicated on the FTC label is measured in accordance with the Test Procedures for Television Sets (USA only).

The actual energy consumption depends on the usage environment (The content watched, TV settings, etc.).

• For information of the power supply and power consumption, refer to the label attached to the product.

- The typical power consumption is measured in accordance with IEC 62087 or each country’s energy regulations.

* On some models, the label is inside the external device connection terminal cover.

* Depending upon the model or country, the typical power consumption may not be on label.

(Depending upon country)

Broadcasting Specifications

Television system ATSC, NTSC-M, 64 & 256 QAM

Program coverage

(Band)

VHF 2-13, UHF 14-69, DTV 2-69, CATV 1-135, CADTV 1-135

External antenna impedance 75Ω

(Only NANO99*)

Wireless module(LGSBWAC94)Specifications

Wireless LAN (IEEE 802.11a/b/g/n/ac)

Frequency range Output Power (Max.)

2,400 to 2,483.5MHz

5,150 to 5,725MHz

5,725 to 5,850MHz

17.5dBm

18dBm

Bluetooth

Frequency range Output power(Max.)

2,400 to 2,483.5MHz 9dBm

As band channels can vary per country, the user cannot change or adjust the operating frequency. This product is configured for the regional

frequency table.

For consideration of the user, this device should be installed and operated with a minimum distance of 20cm (7.8inches) between the device

and the body.

FCC ID: BEJLGSBWAC94 / IC: 2703H-LGSBWAC94

15

ENGLISH_index

(Except for NANO99*)

Wireless module(LGSBWAC92)Specifications

Wireless LAN (IEEE 802.11a/b/g/n/ac)

Frequency range Output Power (Max.)

2,400 to 2,483.5MHz

5,150 to 5,725MHz

5,725 to 5,850MHz

18dBm

Bluetooth

Frequency range Output power(Max.)

2,400 to 2,483.5MHz 8dBm

As band channels can vary per country, the user cannot change or adjust the operating frequency. This product is configured for the regional

frequency table.

For consideration of the user, this device should be installed and operated with a minimum distance of 20cm (7.8inches) between the device

and the body.

FCC ID: BEJLGSBWAC92 / IC: 2703H-LGSBWAC92

Environment condition

Operating Temperature 0°C to 40°C (32°F to 104°F)

Operating Humidity Less than 80%

Storage Temperature -20°C to 60°C (-4°F to 140°F)

Storage Humidity Less than 85%

16

ENGLISH_index

Open Source Software

Notice Information

To obtain the source code under GPL, LGPL, MPL, and other open source

licenses, that is contained in this product, please visit http://opensource.

lge.com.

In addition to the source code, all referred license terms, warranty

disclaimers and copyright notices are available for download.

LG Electronics will also provide open source code to you on CD-ROM

for a charge covering the cost of performing such distribution (such

as the cost of media, shipping, and handling) upon email request to

[email protected]om.

This offer is valid for a period of three years after our last shipment of

this product. This offer is valid to anyone in receipt of this information.

Licenses

(Magic Remote supported models only)

Regulatory

-

17

ENGLISH_index

(1)

(2)

(3)

(4)

NOTE TO CABLE/TV INSTALLER

(For USA and Canada)

This reminder is provided to call the CATV system installer’s attention to

Article 820-40 of the National Electric Code (U.S.A.). The code provides

guidelines for proper grounding and, in particular, specifies that

the cable ground shall be connected to the grounding system of the

building, as close to the point of the cable entry as practical.

18

ENGLISH_index

WARNING!

Never place a television set in an unstable location. A television set may

fall, causing serious personal injury or death. Many injuries, particularly

to children, can be avoided by taking simple precautions such as:

• Using cabinets or stands recommended by the manufacturer of the

television set.

• Only using furniture that can safely support the television set.

• Ensuring the television set is not overhanging the edge of the

supporting furniture.

• Not placing the television set on tall furniture (for example,

cupboards or bookcases) without anchoring both the furniture and

the television set to a suitable support.

• Not placing the television set on cloth or other materials that may

be located between the television set and supporting furniture.

• Educating children about the dangers of climbing on furniture to

reach the television set or its controls.

If your existing television set is being retained and relocated, the same

considerations as above should be applied.

Symbols

Refers to alternating current (AC).

Refers to direct current (DC).

Refers to class II equipment.

Refers to stand-by.

Refer to “ON” (power).

Refers to dangerous voltage.

19

ENGLISH_index

The model and serial number of the product are located

on the back and on one side of the product. Record them

below in case you ever need service.

Model

Serial No.

Supplier`s Declaration of Conformity

Trade Name LG

Responsible Party LG Electronics USA, Inc.

Address 111 Sylvan Avenue, North

Building, Englewood Cliffs,

NJ07632

E-mail [email protected]om

LG Customer Information Center

For inquires or comments, visit www.lg.com or

call;

1-888-542-2623 CANADA

1-800-243-0000 USA, Consumer User

1-888-865-3026 USA, Commercial User

Register your product Online!

www.lg.com

La page charge ...

LG 75NANO95UNA Le manuel du propriétaire

Ce manuel convient également à

LG 75NANO95UNA Le manuel du propriétaire

dans d''autres langues

Documents connexes