Kozyheat Nordik 41DV Le manuel du propriétaire

1 Rev. 11 — May 2023

KOZY POWER VENT #KPV

Kozy Power Vent Approved Fireplaces:

#ALP-36S, #BHM38, #BHM-44, #BHM-52, #CLW-40, #CLW-50,

#CLW-72, #CLW-ST, #NDK-41-DV

English and French installation manuals are available through

your local dealer. Visit our website www.kozyheat.com.

Les manuels d’installation en français et en anglais sont dispo-

nibles chez votre détaillant local. Visitez www.kozyheat.com.

READ ALL THESE STEPS BEFORE STARTING INSTALLATION.

LEAVE TEHSE INSTRUCTIONS WITH THE APPLIANCE.

This kit must be installed by a qualied installer, service

agency, or gas supplier at the me of the heater installa-

on. These instrucons must be used in conjuncon with

the installaon and operaon manual provided with the

appliance.

Please read all appliance owner’s manual completely

before performing any procedures in these instrucons.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

IMPORTANT: Failure to read and follow these instrucons

may create a possible hazard and will void the replace

warranty.

1.0 Introducon ............................................................. 3

1.1 General Informaon ................................................ 3

1.2 Required Components ............................................. 3

1.3 Installaon Informaon ........................................... 3

1.4 Kozy Power Vent Dimensions .................................. 4

1.5 Unit Specic Requirements ..................................... 5

2.0 Venng ..................................................................... 6

2.1 Venng Requirements ............................................. 6

2.2 Dra Bypass Adjustment ......................................... 8

3.0 Terminaon Locaons .............................................. 9

4.0 Framing and Clearances ......................................... 10

4.1 Framing Dimensions .............................................. 10

4.2 Clearances to Combusbles .................................. 10

4.3 Rooop Terminaon ............................................. 11

5.0 Finishing Materials ................................................. 12

5.1 Installaons with 1” or Greater Finishing

Materials ................................................................ 12

5.2 Installaons with FInsihing Materials Less

Than 1” Thick ......................................................... 12

6.0 Installaons ........................................................... 13

6.1 Installing Vent Cap ................................................. 13

6.2 Installing Vent Pipe ................................................ 15

6.3 Installing Power Vent Wire Harness ...................... 16

7.0 Electrical Informaon for Installaon ..................... 20

7.1 Wiring to the Appliance ......................................... 20

8.0 Maintenance .......................................................... 22

8.1 Replace Fan Assembly ........................................... 22

8.2 Replace Vacuum Switch ......................................... 23

9.0 Troubleshoong ..................................................... 25

10.0 Replacement Parts ................................................. 27

2 Rev. 11 — May 2023

3 Rev. 11 — May 2023

1.1 General Informaon

The Kozy Power Vent System, #KPV, is cered for use as

a horizontal terminaon cap only for use with the ALP-

36S, BHM-38, BHM-44, BHM-52, CLW-40, CLW-50, CLW-

72, CLW-ST, and NDK-41-DV direct vent replaces.

The Kozy Power Vent System only works with the ap-

proved appliances listed above ulizing the S.I.T. control

system.

Control system informaon:

• The baery-backup feature cannot be used with

#KPV

• The wired wall switch feature cannot be used with

#KPV

The following vent pipe manufacturers are approved for

use with the Kozy Power Vent:

American Metal Products (Ameri-Vent), BDM, ICC, Metal

Fab, Olympia Chimney Supply, Inc., Selkirk, and Simpson

DuraVent.

IMPORTANT OPERATIONAL NOTE: When the control be-

ing used to run the replace is acvated, there will be up

to a 120 second delay before pilot ignion will begin. This

is to allow a pre-ignion purge by the #KPV. If aer 135

seconds the pilot and burner do not light, refer to Secon

6.0 on page 21 of this manual. There will be also 120 sec-

ond post-operaon purge in which #KPV will connue to

run aer the appliance is turned o.

1.2 Required Components

The S.I.T. Power Vent Control Module is required for #KPV

installaon. Kozy Heat Fireplaces ship with a standard

(non-powervent) control module.

The wire harness connecng the #KPV to the appliance is

sold separately. The length of the wire harness needed

varies by installaon.

1.2.3 Oponal Components

If you have thick nishing material where the power vent

will be installed it may be necessary to order the “Power

Vent Finishing Extension Kit” - Part #KPV-FEK.

See Secon 3.5.1 for more informaon on the “Finishing

Extension Kit”.

1.3 Installaon Informaon

1.3.1 Installaon Precauons

This device must be installed by a qualied installer in accord-

ance with these instrucons.

WARNING: Failure to install, operate, and maintain the power

venng system in accordance with manufacturer's instrucons

will result in condions which may produce bodily injury and/

or property damage.

• Safety inspecon of the venng system should be per-

formed before and aer installaon of this power vent.

Installaon of the Kozy Power Vent must comply with

local, regional, provincial, state, and naonal codes and

regulaons.

• DO NOT INSTALL DAMAGED EQUIPMENT OR VENT COM-

PONENTS

• Disconnect electrical power supply before making wiring

connecons.

• Venng of more than one appliance in a common vent

system is prohibited.

• Clearances between the vent pipe and combusble mate-

rials must be maintained.

• NOTE: The fan motor present in this power vent will gen-

erate sound during operaon. The eects of the increased

sound level can be minimized with careful planning during

installaon of the system.

1.3.2 Installaon Guidelines

• The exit terminaon of mechanical dra systems shall not

be less than seven feet above grade when located adja-

cent to public walkways.

• A mechanical draing venng system shall terminate at

least three feet above any forced air inlet located within

10 feet.

1.3.3 Electrical Requirements

• The #KPV operates on 120VAC, 60Hz electrical service

which is supplied at the replace juncon box. The cur-

rent draw of this device is 0.85 amperes.

1.3.4 Painng Requirements

The #KPV may be painted to a desired color. The paint select-

ed must have sucient temperature and environmental

rangs as described below.

• Prior to painng the #KPV cover assembly, sand the ex-

isng coang with sandpaper or steel wool.

• The front of the cap cover assembly may be eld-painted

and cured up to 400 degrees Fahrenheit (204° C). All re-

maining parts of the cap may be painted, but they may

not be cured beyond 190°F (88°C) due to gaskets and

components overheang.

• Certain areas of the cap surface may reach up to 600° F

(316°C). Paints selected should have sucient tempera-

ture rangs.

• Cap cover assembly contains silicone sealant which could

aect adherence of paint. Please advise local painter of

silicone content.

1.0 Introducon

Power Vent Wire Harness

20’ Power Vent Wire Harness KPV-WH20

40’ Power Vent Wire Harness KPV-WH40

60’ Power Vent Wire Harness KPV-WH60

80’ Power Vent Wire Harness KPV-WH80

100’ Power Vent Wire Harness KPV-WH100

Fireplace Components

Power Vent IFC 700-759

4 Rev. 11 — May 2023

Figure 1.1 - #KPV Dimensions

1.4 Kozy Power Vent Dimensions

5 Rev. 11 — May 2023

1.5 Unit Specic Requirements

1.5.1 Alpha 36S

• Model #ALP-36S can have a 4” x 6 - 5/8” reducer right

o the top of the appliance.

• Model #ALP-36S requires a pilot shield to be installed.

The pilot shield is included in the #KPV parts packet.

To install the pilot shield:

 Remove the log set and the burner. See installaon

manual for more informaon.

 Loosen, but do not remove, the (2) screws securing

the pilot assembly to the pilot bracket.

 Insert the pilot shield slots onto the pilot bracket

screws, as shown in Figure 1.2.

 Re-ghten screws.

 Reinstall all components previously removed.

Figure 1.2 - #ALP-36S Pilot Shield Installaon

1.5.3 Bellingham 52

• Model #BHM-52 can have a 4" x 6-5/8" reducer right

o the top of the appliance.

• If your venng conguraon has more vercal length

than horizontal run, we recommend to adjust the

dra bypass seng to #1 for proper ame appear-

ance. Further adjustment may be needed. See Secon

2.2 Dra Bypass Adjustment on page 8.

• Model #BHM-52 requires burner plates to be in-

stalled. The burner plates are included in the #KPV

parts packet.

To install the burner plates:

 Hand-bend the tabs on the burner plates so the tabs

are facing down to hold the burner plates in place.

 Posion the burner plates at the back of the rebox,

as shown in Figure 1.3.

Figure 1.3 - #BHM-52 Burner Plates Installaon

1.5.2 Bellingham 38, Bellingham 44, Callaway ST,

NDK-41-DV

• Model #BHM-38, #BHM-44, and #CLW-ST can have a 4”

x 6 - 5/8” reducer right o the top of the appliance.

1.5.4 Callaway 40, Callaway 50, Callaway 72

• Model #CLW-40, #CLW-50, and #CLW-72 start with a

5” x 8” 45° elbow o the back of the appliance. Next

use the required 4” x 6 - 5/8” reducer right o the

elbow to keep venng inside the minimum chamber

requirements.

6 Rev. 11 — May 2023

2.0 Venng

2.1 Venng Requirements

For informaon on standard procedures for venng the

appliance, refer to the venng secon of your specic ap-

pliance installaon manual.

The #KPV is for use 4" x 6-5/8" coaxial rigid direct vent

pipe. Depending on your appliance, the vent size must be

reduced to 4" x 6-5/8". See appliance installaon manual

for approved venng.

The #KPV system must terminate horizontally.

• A minimum of 1" (25mm) clearance on all sides of the

vercal vent pipe must be maintained. Ac insulaon

shields may be insulated using unfaced insulaon

products listed as noncombusble per ASTM E 136.

• A minimum of 1" (25mm) clearance on all sides of the

horizontal vent pipe at the wall pass-through must be

maintained. Wall thimble products that comply with

the required 1" (25mm) clearance to combusbles

must be installed for all horizontal vent runs that pass

through interior or exterior walls. These wall thimble

products may be insulated using unfaced insulaon

products listed as noncombusble per ASTM E 136.

• For every 1' of vercal drop, the total allowable length

must be reduced by 2'.

• If a pipe conguraon includes a vercal component

that goes downward, a vercal component going back

upward is not allowed.

• No vercal rise is required with #KPV. The venng can

run horizontal directly o the appliance.

• Use Table 2.1 for venng guidelines.

• Use Figure 2.2 as a guide for proper vent installaon.

• Use Figure 2.3 for a guide to calculate total vent run.

Terminaon must be in shaded area.

Figure 2.1 - Prohibited Vercal Drop Venng Conguraon

Figure 2.2 - Horizontal Terminaon Example

7 Rev. 11 — May 2023

Figure 2.3 - Horizontal Terminaon Guide

Table 2.1 - KPV Venng Guidelines

Maximum Elbows (8) 90° or (16) 45°

Minimum Total Horizontal Vent Run Models #ALP-36S, #CLW-40, #CLW-50, #CLW-ST, #CLW-72, #NDK-41-DV: 6’ (1.8m)

Models #BHM-38, #BHM-44, #BHM-52: 10’ (3m)

Maximum Total Horizontal Vent Run 60’ (18.3m) Do not exceed 60’

Maximum Vercal Vent Run 60’ (18.3m) Do not exceed 60’

Maximum Vercal Drop Allowed 8’ (2.4m) For every 1’ (30cm) of vercal drop the maximum total vent run is reduced by

2’ (61cm)

Maximum Total Vent Run 100’ (30m)

8 Rev. 11 — May 2023

2.2 Dra Bypass Adjustment

NOTE: All Kozy Power Vent systems will be shipped with

the dra bypass in seng 5. Adjustment of the dra by-

pass seng would only occur during troubleshoong or

ame appearance adjustments.

The dra bypass system is factory set to seng 5; for cer-

tain vent runs the dra bypass system will need to be ad-

justed. To adjust the dra bypass, loosen the locking

screw. Adjust clock wise or counter clockwise depending

on your specic installaon. See Figures 2.4, 2.5, and 2.6.

Table 2.2 - #ALP-36S, #BHM-38, #BHM-44, #BHM-52, #CLW-40,

#CLW-50, #CLW-ST, #NDK-41-DV Dra Bypass Seng Chart

Natural Gas Propane

Dra Seng

#1 Allowed Allowed

#2 Allowed Allowed

#3 Allowed Allowed

#4 Allowed Allowed

#5 Allowed Allowed

Table 2.3 - #CLW-72 Dra Bypass Seng Chart

Natural Gas Propane

Dra Seng

#1 Not Allowed Allowed*

#2 Not Allowed Allowed*

#3 Allowed Allowed

#4 Allowed Allowed

#5 Allowed Allowed

* This dra seng is allowed on all vent conguraons except a

vent conguraon with a vercal drop.

Figure 2.4 - Loosen Locking Screw

Figure 2.5 - Adjust the Dra Bypass

Figure 2.6 - Shown in Posion 3

9 Rev. 11 — May 2023

3.0 Terminaon Locaons

3.1 Terminaon Cap Clearances

Canadian Installaons US Installaons

A Clearance above grade, veranda, porch, desk, or balcony. 12” (30cm) 12” (30cm)

B Clearance to window or door that may be opened 12” (30cm) 9” (23cm)

C Clearance to permanently closed window (recommended to prevent condensaon on window) 12” (30cm)* 12” (30cm)*

D Vercal clearance to venlated sot located above the terminal within a horizontal distance of 2 feet

(61cm) from the edge of the terminal 0” (0cm)* 0” (0cm)*

E Clearance to unvenlated sot 0” (0cm)* 0” (0cm)*

F Clearance to outside corner 0” (0cm)* 0” (0cm)*

G Clearance to inside corner 12” (30cm)* 12” (30cm)

H Clearance to each side of center line extended above meter/regulator assembly 3’ (91cm) within a height

15’ (4.5m) above the

meter/regulator assembly

*

I Clearance to service regulator vent outlet 3’ (91cm) *

J Clearance to non-mechanical air supply inlet to building or the combuson air inlet to any other appliance 12” (30cm) 9” (23cm)

K Clearance to mechanical air supply inlet 6’ (1.83m) 3’ (91cm) above

[Massachuses: 10’ (3m)

above] if within 10’ (3m)

horizontally

L Clearance above paved sidewalk or paved driveway located on public property 7’ (2.13m)† *

M Clearance under veranda, porch deck, or balcony 0” (0cm)‡ 0” (0cm)

N Clearance between two horizontal terminaons 12” (30cm) 12” (30cm)

O Clearance between two vercal terminaons (may be same height) 12” (30cm) 12” (30cm)

P Above furnace exhaust or inlet 12” (30cm) 12” (30cm)

* Clearance in accordance with local installaon codes and the requirements of the gas supplier

†A vent shall not terminate directly above a sidewalk or paved driveway that is located between two single family dwellings and serves both dwellings.

‡ Permied only if veranda, porch, desk, or balcony is fully open on a minimum of two sides beneath the oor

VINYL SOFFIT, VINYL CEILING, AND VINYL OVERHANG DISCLAIMER: Clearances to heat resistant material (i.e. wood, metal). This does not include vinyl. Hussong Manufac-

turing Co., Inc. will not be held responsible for heat damage caused from terminang under vinyl overhangs, vinyl ceilings, or vinyl venlated/unvenlated sots.

Figure 3.1 - Minimum Terminaon Cap Clearances

10 Rev. 11 — May 2023

4.0 Framing and Clearances

4.1 Framing Dimensions

• Dimensions are shown in Figure 4.1

• Construct a framework as shown in Figure 4.2. Frame-

work material should be the same dimensions as the

material used for the wall framing.

Figure 4.2 - Framing Dimensions

IMPORTANT: Framework for #KPV must be level

to ensure precipitaon does not build up inside

the power vent unit.

4.2 Clearances to Combusbles

Figure 4.3 - Minimum Clearances to Combusbles

11 Rev. 11 — May 2023

Figure 4.5 - Minimum Clearances for Rooop Terminaon

4.3 Rooop Terminaon

If the #KPV is going to terminate on a at roof, an enclosure similar to the one shown in Figure 4.3 needs to be construcon.

Figure 4.3 - Roof top terminaon example

Figure 4.4 - Terminaon Top Cleareance

12 Rev. 11 — May 2023

5.0 Finishing Materials

NOTE: If your installaon has exterior nishing materials

greater than 1" (25mm) thick, a #KPV-FEK Finishing Ex-

tension Kit will be needed. The extension kit must be

installed to allow for thicker exterior nishing materials

for proper installaon and ng of the #KPV.

IMPORTANT: IT IS IMPERATIVE THAT #KPV-FEK IS LEVEL

TO ENSURE THE POWER VENT IS LEVEL. THIS IS RE-

QUIRED TO ENSURE PRECIPITATION DOES NOT BUILD UP

INSIDE THE CAP. Care should be taken to ensure #KPV-

FEK is secured at to the wall.

NOTE: The provided high temperature clear silicone is to

be used where sealant is required in this secon. If you

need addional sealant, it must have a minimum of 300°

F connuous exposure rang.

If installing nishing material less than 1" (25mm) thick,

skip to Secon 5.2

5.1 Installaon with 1” or Greater Finishing

Materials

1. Assemble the Finishing Extension Kit and place assem-

bled box over the framed opening in the wall with

mounng anges placed at the top and boom of the

building exterior.

2. Secure the Finishing Extension Kit extension box to

the building. Ensure the Finishing Extension Kit is

squared on the framed opening. See Figure 5.1. Seal

all corners, joints, and bend lines with silicone caulk.

Ensure all gaps and holes are lled so a sealed enve-

lope is formed.

3. The wall is now ready to be nished. Finishing materi-

als such as stone/brick can then be installed up to the

sides/projecon of the Finishing Extension Kit . This

will ensure that the cap will t into the opening aer

nishing has been completed. It is important that the

outside anges of the Finishing Extension Kit must not

have any pressure on them from the nishing materi-

als to inhibit the installaon of the Kozy Power Vent.

Proceed to Secon 6.0 for more informaon on instal-

laon steps.

4. Silicone should be applied around the outer edge of

Finishing Extension Kit where it meets the building

exterior.

5. Proceed to installing the Kozy Power Vent, Secon

6.0.

5.2 Installaon With Finishing Materials Less

Than 1” Thick

Important: Ensure the nishing material does not put

pressure against the edges of the Kozy Power Vent. The

front cover must be able to be removed for maintenance

and service.

• You are able to directly install the power vent to the

exterior of the wall and bu nishing material against

the nishing edge.

• Proceed to installing the Kozy Power Vent, Secon 6.0

Figure 5.1 - Install FEK and Seal FEK

Figure 5.2 - Silicone FEK

13 Rev. 11 — May 2023

6.0 Installaon

6.1 Installing Vent Cap

1. Remove the (4) screws securing the front cover to the

Kozy Power Vent.

2. Remove the eight screws securing the back assembly to

the cap. See Figure 6.1.

3. Slide the exhaust assembly out of the back of the cap. See

Figure 6.2.

Note: Before proceeding with the next steps of wiring the Kozy

Power Vent and securing the Kozy Power Vent to the Finishing

Extension Kit or framed opening it may be necessary to con-

nect the wire harness to the back plate of the power vent as-

sembly. The wiring harness would be fed through this framed

opening and connected to the power vent back plate assem-

bly. You would then reconnect the back plate assembly to the

power vent shell. If you have adequate access to the backside

of where the power vent will be mounted you can run and se-

cure the wire harness at a later me if desired.

4. Install #KPV wiring harness through the electrical access

hole in the back cover cap. See Figure 6.3.

5. Place a bead of silicone on the backside of the power vent

assembly as shown in Figure 6.5. This silicone will seal the

power vent cap to the framed opening of the exterior of

the building or to the Finishing Extension Kit.

5. Install the Kozy Power Vent shell into the framed opening

if nishing material is 1” thick or less. Secure the assembly

to the framed opened through the (8) holes shown in 6.4.

Install the Kozy Power vent to the Finishing Extension Kit

using (8) threaded screws provided if the nishing material

is greater than 1” thick. These (8) holes are located with

(2) each side of the rubber gasket.

6. If the cap is fastened to the wall, apply a bead of silicone

(with a minimum of 300°F connuous exposure rang)

around the cap base where it meets the exterior wall. See

Figure 6.8. If the cap is fastened to a Finishing Extension

Kit apply a bead of silicone around the outside seam

where the Kozy Power Vent and FInishing Extension Kit

meet.

Figure 6.1 - Rear Plate Screws

Figure 6.2 - Rear Plate Removal

Figure 6.3 - Electrical Hole Rear Plate

Figure 6.4 - Mounng Holes

14 Rev. 11 — May 2023

Figure 6.5 - Silicone Backside Figure 6.6 - Secure Power Vent to Exterior

Figure 6.7 - Installaon to FEK Figure 6.8 - Installaon to Exterior Wall

15 Rev. 11 — May 2023

6.2 Installing Vent Pipe

• Refer to Secon 2.0 Venng for vent requirements.

• Apply a bead of the provided sealant around the inner exhaust pipe connecon on the replace and the power vent as-

sembly. See Figures 6.9 and 6.10.

• Each individual pipe manufacturer may require or recommend addional sealant in between each vent pipe connecon.

Aer compleng the vent pipe installaon, ensure all of the vent pipe connecons are sealed properly before replace

operaon.

Figure 6.9 - Silicone Inner Exhaust on Power Vent Assembly

Figure 6.10 - Silicone Inner Exhaust on Fireplace

16 Rev. 11 — May 2023

6.3 Installing Power Vent Wire Harness

See Figure 6.13, Power Vent Internal Wiring on Page 17 for wiring schemac accompanying these instrucons.

Complete the necessary electrical preparaon in Secon 7.0 before connecng the wire harness to the replace.

1. Aer mounng the wiring harness to the back assembly of the Kozy Power Vent in step #4 of Secon 6.1 you will pro-

ceed with wiring connecons at the power vent. Aach the red and brown wires to the vacuum switch as shown in

Figure 6.11.

2. Aach the white and black wires from the #KPV harness to the black wires coming from the blower. Aach the green

wire from the #KPV harness to the green/yellow wire coming from the fan.

NOTE: Aer all wires are connected, the wire should look like the picture in Figure 6.12.

Figure 6.11 - Red and Brown Wiring to Vacuum Switch

Figure 6.12 - Exhaust Fan wiring

17 Rev. 11 — May 2023

Figure 6.13 - Power Vent Internal wiring

18 Rev. 11 — May 2023

NOTE: Use Figure 7.4 (pg. 21) as wiring schemac refer-

ences when following the individual instrucons below.

3. Next we are wiring the other end of the wire harness

to the replace. Locate the power vent wire harness

hole(s) on the replace. Your model may have one

hole on one side of the replace, or one hole on ei-

ther side of the replace. Plan accordingly when or-

dering your KPV wire harness. The power vent wire

harness holes are located on a removable plate. Re-

move screws that aach the plate to the outer shell

for easier access. Reaach the plate when nished.

See Figure 6.14.

4. Run the loose wiring through the larger secon of the

opening unl you reach the start of the exible con-

duit. Unscrew the nut from the conduit end and slide

the conduit end into the smaller secon of this open-

ing. Screw the locking nut back on the threads of the

conduit securing it to the replace. See Figure 6.15.

5. Ensure you complete the necessary preparaon steps

in Secon 7.0 before this step. Locate the Power Vent

IFC wire harness in the components packet. Plug the

connector into X12 and X13 plug receptor. See Figure

6.16.

Figure 6.14 - Power Vent Wire Harness Hole Locaon

(Callaway 40 Shown)

Figure 6.15 - Run Wiring Through Opening and Secure

Figure 6.16 - Power Vent IFC Wire Harness and the

X12/X13 Locaon on IFC Module

19 Rev. 11 — May 2023

4. Now we will connect the power vent wire harness to the control module and replace wire harness. The power vent wire

harness has the black hot wire split with two female quick connecons on either end. Plugs these into the black leads that

have quick connecons coming o the control module in the X12 combuson blower locaon. See Figure 6.17.

5. Locate the blue looped wire on the control module wire harness that connects to the IPI/CPI locaon on the control mod-

ule. Cut this looped wires so you have two individual blue wires.

6. Locate the yellow looped "APS" wire on the control module wire harness. Cut this looped wire for two individual yellow

wires. Strip back approximately 1/2" of the end of each wire. Using the (2) provided blue wire nuts, twist one of the yellow

APS wires into the brown wire coming from the vacuum switch in the power vent assembly. Use the second blue wire nut

to twist the second yellow APS wire to the red wire coming from the vacuum switch as shown in Figure 6.18.

7. If not completed - Run the other end of the power vent wiring to the power vent terminaon assembly. For aaching the

wire harness to the fan and vacuum switch, refer to Secon 6.3 on page 16.

8. Connect the three prong plug into the electrical box in the replace.

Figure 6.17 - Wire Harness - Quick Connecon to Black Leads

Figure 6.18 - APS Wire Nuts

20 Rev. 11 — May 2023

7.0 Electrical Informaon for Installaon

7.1 Wiring to the Appliance

NOTE: Electrical wiring must be done in accordance with naonal, pro-

vincial, and/or local electrical codes.

WARNING: Disconnect electrical power from replace/power vent be-

fore performing any maintenance, repair, or electrical wiring.

NOTE: Electrical service of 120 VAC-60Hz must be supplied to the junc-

on box of the replace in order for the power vent to operate correct-

ly. The current draw of this device is 0.85 amperes.

Ensure that the proper clearances are maintained for wiring and con-

duit. When installing the wiring, it must never run above the vent run

and it must be a minimum 1" (25mm) from all venng.

The baery back up will not run with power venng installed.

7.1.1 Prepare Power Vent Control Board

The S.I.T. Power Vent control board is sold separately and must be in-

stalled in place of the control module that was shipped with the re-

place.

 Use a at blade screwdriver to pry the tabs of the top cover of the

control module to release.

 Locate the JP1 jumper. It is a small plasc jumper that connects two

pins as shown in Figure 7.2.

 Pull the plasc jumper straight up to expose the two individuals

pins underneath it. This changes the control module funcon from

a natural dra system to a power vent system. See Figure 7.3.

 Reinstall control module top cover. Plug in all components previ-

ously unplugged.

7.1.2 Power Vent Control Board Installaon

 Remove the control board from housing (2) screws, and disconnect

all wires. Refer to the installaon manual included with the re-

place.

 Install the Power Vent Control Board and reconnect the wiring as

previously removed.

 Now we will connect the wire harness to the new control module.

Figure 7.1 - Remove IFC Cover

Figure 7.2 - Locate JP1 Jumper

Figure 7.3 - Remove JP1 Jumper

La page charge ...

Kozyheat Nordik 41DV Le manuel du propriétaire

Kozyheat Nordik 41DV Le manuel du propriétaire

Documents connexes

Autres documents