GE GFD14ESSNWW Le manuel du propriétaire

GE is a trademark of the General Electric Company. Manufactured under trademark license.

0020507767GE 49-3000087 Rev 3 04-23 GEA

DRYERS

SAFETY INFORMATION ..........3

USING THE DRYER

Getting Started ...................... 4

Loading ..............................8

Features ..............................8

CARE AND CLEANING ...........9

INSTALLATION

INSTRUCTIONS .....................11

Stacking (Optional) .....................24

Reversing The Door Swing (Optional).....26

TROUBLESHOOTING TIPS......28

LIMITED WARRANTY ...........31

CONSUMER SUPPORT ..........32

GFD14

OWNER’S MANUAL &

INSTALLATION

INSTRUCTIONS

Write the model and serial

numbers here:

Model #_________________

Serial # _________________

They are on the label on the front

of the dryer behind the door.

ENGLISH/FRANÇAIS/

ESPAÑOL

249-3000087 Rev 3

THANK YOU FOR MAKING GE APPLIANCES A PART OF YOUR HOME.

Whether you grew up with GE Appliances, or this is your first, we’re happy to have you in the family.

We take pride in the craftsmanship, innovation and design that goes into every GE Appliances

product, and we think you will too. Among other things, registration of your appliance ensures that we

can deliver important product information and warranty details when you need them.

Register your GE appliance now online. Helpful websites and phone numbers are available in the

Consumer Support section of this Owner’s Manual. You may also mail in the pre-printed registration

card included in the packing material.

49-3000087 Rev 3 3

READ AND SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE

To reduce the risk of fire, explosion, electric shock, or injury to persons when using your appliance,

follow basic precautions, including the following:

Ŷ

Read all instructions before using the appliance.

Ŷ

DO NOT dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline,

dry-cleaning solvents, or other flammable or explosive substances, as they give off vapors that could ignite or

explode.

Ŷ DO NOT place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may contribute to a

chemical reaction that could cause a load to catch fire. To reduce the risk of fire due to contaminated loads, the final

part of the tumble dryer cycle occurs without heat (cool down period). Avoid stopping a tumble dryer before the end

of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated.

Ŷ

DO NOT allow children to play on or in this appliance. Close supervision of children is necessary when this

appliance is used near children.

Ŷ

Before the appliance is removed from service or discarded, remove the door to the drying compartment.

Ŷ

DO NOT reach into the appliance if the drum is moving.

Ŷ

DO NOT install or store this appliance where it will be exposed to the weather.

Ŷ

DO NOT tamper with controls.

Ŷ

DO NOT climb or stand on this unit.

Ŷ DO NOT repair or replace any part of this appliance or attempt any servicing unless specifically recommended

in the user-maintenance instructions or in published user-repair instructions that you understand and have the

skills to carry out.

Ŷ Follow all fabric care instructions and warnings to prevent melting of garments or damage to the appliance.

Ŷ

DO NOT use fabric softeners or products to eliminate static unless recommended by the manufacturer of the

fabric softener or product.

Ŷ DO NOT dry articles containing foam rubber or similarly textured rubber-like materials.

Ŷ Clean lint screen before or after each load.

Ŷ DO NOT operate the dryer without the lint filter in place.

Ŷ DO NOT store combustible materials, gasoline or other flammable liquids near the dryer. Keep area around the

exhaust opening and adjacent surrounding areas free from the accumulation of lint, dust and dirt.

Ŷ

The interior of the appliance and exhaust duct should be cleaned periodically by qualified service personnel.

Ŷ

Unplug the appliance or turn off the circuit breaker before servicing. Pressing the Power or Start/Pause button DOES

NOT disconnect power.

Ŷ

DO NOT operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or

broken parts, including a damaged cord or plug.

Ŷ

DO NOT spray any type of aerosol into, on or near dryer at any time. DO NOT use any type of spray cleaner when

cleaning dryer interior. Hazardous fumes or electrical shock could occur

.

Ŷ

See “ELECTRICAL CONNECTION” located in the Installation Instructions for grounding instructions.

WARNING

SAFETY INFORMATION

Proper Disposal of your Appliance

Ŷ

Dispose of or recycle your appliance in accordance with Federal and Local Regulations. Contact your local

authorities for the environmentally safe disposal or recycling of your appliance.

Ŷ

Consider recycling options for your appliance packaging material.

449-3000087 Rev 3

Getting started

USING THE DRYER

Throughout this manual, features and appearance may vary from your model.

Controls

• If the screen is dark,

press the Power button

to “wake up” the display.

Step 2 Step 3 Step 4

Step 1

• Select a dry cycle.

(Defaults are set for

each dry cycle. These

default settings can

be changed. See

control settings for

more information.)

OR

• Press the

Start/Pause

button.

• Loosely add items.

• Close door.

NOTE: Dryer will not start

with door open.

To reduce the risk of fire, electric shock, or injury to persons, read the IMPORTANT SAFETY

INFORMATION before operating this appliance.

WARNING

Power

• Press Timed Dry

button, rotate knob

to adjust time, and

press Temp button

to set your own

temperature.

Start

Pause

Temp

Timed

Dry

Damp DelayDamp

Dry

Ex Dry

Damp Timed

Clean Filter

No Heat

Low

High

Medium

DRY DAMP COOL

Est Time Remaining

Tumble

My Cycle

Power

Start

Pause

Warm Up

Rack Dry

Quick Dry

Delicates

Cottons

Heavy

Duty

Active

Wear

Casuals

To w e l s

Sanitize

Dewrinkle

Mixed Loads

Timed

Dry

Damp

Alert

Level Ext

Tumble

My Cycle

Temp eDry

Hold to Set

Delay

Dry

Low Air eDry

C

L AKBM

D E F H I J

N

G

49-3000087 Rev 3 5

USING THE DRYER

Getting started

BDry Cycles

The dry cycle controls the cycle time for the drying process. The chart below will help you match

the dry setting with the loads.

Mixed Loads

or Normal

(Depending on

model)

For loads consisting of cottons and poly blends.

Cottons For cottons and most linens. NOTE: Energy Star® models are tested on Cottons with

default settings.

Heavy Duty For large coats, bed spreads, mattress covers, sleeping bags, blankets, comforters, jackets,

small rugs, and similar large and bulky items.

Towels Use for towels OR sheets. It is not recommended to mix towels and sheets in the same load.

Casuals For wrinkle-free, permanent press and delicate items, and knits.

Active Wear Clothing worn for active sports exercise and some casual wear. Fabrics include new technology

finishes and stretch fibers such as Spandex. Also for clothing labeled Easy Care or Perma Press:

For wrinkle-free and permanent press items.

Sanitize Reduces certain types of bacteria by 96.7%, including: Staphylococcus aureus and Pseudomonas

aeruginosa. The antibacterial process occurs when high heat is used during a portion of this

drying cycle.

Quick Dry For small loads that are needed in a hurry, such as sports or school uniforms. Can also be

used if the previous cycle left some items damp, such as collars or waistbands.

Delicates For lingerie and special-care fabrics.

Dewrinkle For removing wrinkles from items that are dry or slightly damp. This cycle is not recommended

for delicate fabrics.

Warm Up Provides 25 minutes of warming time to warm up clothes.

Air Fluff Provides 30 minutes of tumbling time without heat.

Rack Dry For drying delicate items without tumbling, use drying rack accessory. Place items flat on the

drying rack such as wool sweaters and delicate fabrics. Dry with low heat.

APower

Press to “wake up” the display. If the display is active, press to turn the dryer off.

NOTE: Pressing Power does not disconnect the appliance from the power supply.

CTemp (Temperature)

You can change the temperature of your dry cycle.

Temp

High For regular to heavy cottons.

Medium For synthetics, blends and items labeled Permanent Press.

Low For delicates, synthetics and items labeled Tumble Dry Low.

No Heat This option may only be used with Air Fluff and Timed Dry, in which items are

tumbled without heat.

649-3000087 Rev 3

Getting started

USING THE DRYER

Extended Tumble

Minimizes wrinkles by adding approximately 2 hours of no-heat tumbling after clothes are

dry.

The estimated time remaining display will show “END”.

The extended tumble time does not get added to the cycle time on the display.

I

DLevel

The sensor continuously monitors the amount of moisture in the load. When the moisture in

your clothes reaches your selected dry level, the dryer will stop.

NOTE: Sensor dry Level can be used with all cycles except Timed Dry, Air Fluff, Rack

Dry, Warm Up and Dewrinkle.

EDamp Alert

This option causes the dryer to beep when clothes have dried to a damp level. Remove

items that you wish to hang dry. The Damp Alert will only beep when this option is selected,

and the dryer will continue to dry.

Removing clothes and hanging them when they are damp can reduce the need to iron some items.

Damp

Alert

FTimed Dry

1. Press Timed Dry button. Lights around the knob will flash. Select the drying time by

rotating the knob to increase or decrease the time in 10-minute increments up to 2 hours

and 30 minutes.

2. Select the dry Temp.

3. Close the door.

4. Press Start/Pause.

HMy Cycle

Set up your favorite combination of settings and save them here for one touch recall. These

custom settings can be set while a cycle is in progress.

To store a My Cycle combination of settings:

1. Select your drying cycle.

2. Change Temp and Level settings to fit your needs.

3. Select any drying options you want.

4. Press and hold the My Cycle button for 3 seconds to store your selection. A beep will

sound and the button will light up.

To recall your stored My Cycle combination:

Press the MY CYCLE button before drying a load.

To change your stored My Cycle combination:

Repeat steps 1–4.

My Cycle

Hold to Set

Level

Ex Dry Use for heavy-duty fabrics or items that should be very dry, such as towels.

Dry Use for normal dryness level suitable for most loads. This is the preferred cycle for energy saving.

Damp For leaving items partially damp.

Timed

Dry

Tumble

Ext

GeDry (on some models)

Reduces total energy consumption of specific dryer cycles by adjusting certain heat settings.

NOTE: Cycle times will change when eDry is selected.

Energy Star® models are tested on Cottons cycle with default settings to determine energy

use rating of this dryer. The eDry option will default to on for Cottons. Temperature settings

on High and dryness level setting on Dry are specifically designed for this cycle to reduce

energy consumption. For optimal energy savings, turn eDry on. For optimal drying times,

turn eDry off. Energy savings will vary across loads and cycles.

The eDry selection can be used with Mixed Loads, Cottons, Heavy Duty, Towels,

Casuals, Active Wear and Delicates.

eDry

49-3000087 Rev 3 7

USING THE DRYER

Getting started

JDelay Dry

Use to delay the start of your dryer.

1. Choose your dry cycle and any options.

2. Press Delay Dry. You can change the delay time in 1 hour increments, using the Delay Dry

button.

3. Press the Start/Pause button to start the countdown.

NOTE: If the door is opened while the dryer is in Delay Dry, the countdown time will not

restart unless the door is closed and Start/Pause button has been pressed again.

KStart/Pause

Press to start a cycle. If the dryer is running, pressing it once will pause the dryer and unlock

the door. This function can be used to add garments during a cycle. Press again to restart

the cycle.

NOTE: If the dryer is paused and the cycle is not restarted within 15 minutes, the current

cycle will be cancelled.

LLock

You can lock the controls to prevent any selections from being made. Or you can lock or

unlock the controls after you have started a cycle.

Children cannot accidentally start the dryer by touching pads with this option selected.

To lock the dryer, press and hold the Temp and Level buttons together for 3 seconds.

To unlock the dryer controls, press and hold the Temp and Level buttons together for 3

seconds. A sound is made to indicate the lock/unlock status.

The control lock icon on the display will light up when it is on.

NOTE: The Power button can still be used when the machine is locked.

Level

Temp

Start

Pause

MSignal

When the light is on, the dryer will beep at the end of the cycle and every time you press a

button on the control panel.

To turn the signal off, press and hold the Level and Damp Alert buttons together for 3 seconds.

A sound is made to indicate the lock/unlock status.

Delay

Dry

Level Damp

Alert

NDisplay and Status Lights

The display shows the approximate time remaining until the end of the cycle.

In addition, this display will show the dryer status:

Damp DelayDamp

Dry

Ex Dry

Damp Timed

Clean Filter

No Heat

Low

High

Medium

DRY DAMP COOL

Est Time Remaining

Tumble

My Cycle

LowAir eDry

Status DRY DAMP COOL

Controls locked on.

End of cycle signal on.

Clean Filter Time to clean the filter. See the Care and Cleaning section.

Low Air Indicates decrease in performance of the dryer and increase risk of lint accumulation in the ducts and

dryer.

eDry Shows eDry setting selected.

Temp Shows High, Medium, Low or No Heat temperature setting selected.

Level Shows Extra Dry, Dry or Damp dryness setting selected.

Damp Alert Indicates Damp Alert is set and will sound when the clothes have dried to a damp dryness level.

Timed Indicates that a Timed Dry cycle is set. Will turn off after cycle is finished.

Est Time

Remaining Display shows the estimated time remaining until set cycle is completed.

My Cycle Indicates the My Cycle feature is set.

Ext Tumble Indicates the Extended Tumble feature is set.

Indicates Delay Dry is set time is selected.

849-3000087 Rev 3

Loading

USING THE DRYER

Fabric Care Labels

Below are fabric care label “symbols” that affect the clothing you will be laundering.

Dry Labels

Always follow fabric manufacturer’s care label when laundering.

As a general rule, if clothes are sorted properly for the washer, they are sorted properly for the dryer. Try also to

sort items according to size. For example, do not dry a sheet with socks or other small items.

Do not add fabric softener sheets once the load has become warm. They may cause fabric softener stains. Bounce®

Fabric Conditioner Dryer Sheets have been approved for use in this dryer when used in accordance with the

manufacturer’s instructions.

Do not overload. This wastes energy and causes wrinkling.

• Keep flammable materials and vapors, such as

gasoline, away from dryer.

• DO NOT dry anything that has ever had anything

flammable on it (even after washing).

• No washer can completely remove oil.

• DO NOT dry anything that has ever had any type of oil

on it (including cooking oils).

• Items containing foam, rubber, or plastic must be dried

on a clothesline.

• Failure to do so can result in death, explosion, or fire.

Sorting and Loading Hints

Tumble

dry

Dry Normal Permanent Press/

wrinkle resistant Gentle/

delicate Do not tumble dry Do not dry

(used with

do not wash)

Heat

setting

High Medium Low No heat/air

Special

instructions Line dry/

hang to dry Drip dry Dry flat In the shade

- Fire Hazard

WARNING

Drying Rack

A handy drying rack may be used for drying delicate items such as washable sweaters. Place items flat on the

drying rack and block such items as wool sweaters and delicate fabrics. Dry with low heat.

To install the drying rack, extend the drying rack into the dryer drum and rest the front two

legs on the front angled ledge.

NOTES:

Ŷ The drying rack is designed for use with the Timed Dry cycle. Use with sensor cycles

may result in damp items or extended cycle times.

Ŷ Do not use this drying rack when there are other clothes in the dryer, that are not placed on the rack.

Ŷ The drying rack, WE01X26416, is available as an accessory. Order on-line at GEApplianceparts.com, 24 hours

a day or by phone at 877.959.8688 during normal business hours.

49-3000087 Rev 3 9

CARE AND CLEANING

Care and cleaning

Exterior

Wipe or dust any spills or washing compounds with a damp cloth. Dryer control panel and finishes may be damaged

by some laundry pretreatment soil and stain remover products. Apply these products away from the dryer. The fabric

may then be washed and dried normally. Damage to your dryer caused by these products is not covered by your

warranty.

Stainless Steel

To clean stainless steel surfaces use a damp cloth with a mild, non-abrasive cleaner suitable for stainless steel

surfaces. Remove the cleaner residue and then dry with a clean cloth.

The stainless steel used to make the dryer drum provides the highest reliability available in a GE Appliances dryer.

If the dryer drum should be scratched or dented during normal use, the drum will not rust or corrode. These surface

blemishes will not affect the function or durability of the drum.

Interior and Duct

The interior of the appliance and exhaust duct should be cleaned once a year by qualified service personnel.

The Exhaust Duct: Inspect and clean the exhaust ducting at least once a year to prevent clogging. A partially clogged

exhaust can lengthen the drying time.

The Exhaust Hood: Check with a mirror that the inside flaps of the hood move freely when operating. Make sure that there

is no wildlife (birds, insects, etc.) nesting inside the duct or hood.

Lint Filter

Clean the lint filter before each use.

Pull out the lint filter. Moisten your fingers and remove the captured lint. Once clean, slide

the filter back into position. Have a qualified technician vacuum the lint from the dryer once

a year.

NEVER OPERATE THE DRYER WITHOUT ITS FILTER IN PLACE.

10 49-3000087 Rev 3

Care and cleaning

CARE AND CLEANING

Drum Lamp

NOTE: The drum lamp is not consumer replaceable on models where there is a flat cover

over an LED bulb. If this light should ever stop working, call for service.

For models that have a domed cover over the bulb secured by a screw:

Before replacing the light bulb, be sure to unplug the dryer power cord or disconnect the

dryer at the household distribution panel by removing the fuse or switching off the circuit

breaker. Reach above dryer opening from inside the drum to locate the light.

Remove the screw and the plastic cover to access the bulb. Replace with the appropriate

bulb and then reaffix the cover and screw.

Order replacement bulb WE11X26351 on-line at GEApplianceparts.com, by phone at 877.959.8688 during normal

business hours, or purchase appliance bulb 7C7 from your local retailer.

When the door is opened, the drum lamp automatically turns on and remains on for 2 minutes. When the door is closed,

the drum lamp will remain on for 30 seconds.

Disconnect power supply before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

- Electrical Shock Hazard

WARNING

49-3000087 Rev 3 11

Installation

Dryer

Instructions

If you have any questions, call GE Appliances at 800.GE.CARES

(800.432.2737) or visit our Website at: GEAppliances.com

In Canada, call 800.561.3344 or visit www.GEAppliances.ca

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• IMPORTANT – Save these instructions for

local electrical inspector’s use.

• IMPORTANT – Observe all governing

codes and ordinances.

• Install the clothes dryer according to the

manufacturer’s instructions and local codes.

• Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these instructions for

future reference.

• Clothes dryer installation must be performed by a

qualified installer.

• This dryer must be exhausted to the outdoors.

• Before the old dryer is removed from service or

discarded, remove the dryer door.

• Service information and the wiring diagram are

located in the control console.

• Do not allow children on or in the appliance. Close

supervision of children is necessary when the

appliance is used near children.

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not

covered under the Warranty.

• Install the dryer where the temperature is above

50°F for satisfactory operation of the dryer control

system.

• Remove and discard existing plastic or metal foil

duct and replace with UL-listed duct.

- Risk of Fire

• Clothes dryer installation must be performed by a

qualified installer.

• Install the clothes dryer according to these

instructions and local codes.

• DO NOT install a clothes dryer with flexible plastic

venting materials. If flexible metal (semi-rigid or

foil-type) duct is installed, it must be UL-listed and

installed in accordance with the instructions found

in “Connecting the Dryer to House Vent” later in

this manual. Flexible venting materials are known

to collapse, be easily crushed and trap lint. These

conditions will obstruct dryer airflow and increase

the risk of fire.

• DO NOT install or store this appliance in any

location where it could be exposed to water or

weather.

• To reduce the risk of severe injury or death, follow

all installation instructions.

• Save these instructions. (Installers: Be sure to

leave these instructions with the customer.)

If you are planning to stack the washer and dryer, order

Stacking Kit number GFA24KITL to be used for this

dryer. Kit sold separately.

WARNING

12 49-3000087 Rev 3

*NOTE:

With leveling legs retracted: 33-1/4 (84.5 cm)

With leveling legs fully extended: 33-5/8 (85.4 cm)

Stacked: 66-1/2” (168.9 cm)

Installation Instructions

Tilt the dryer sideways and remove the foam shipping pads by pulling at the sides and

breaking them away from the dryer legs. Be sure to remove all of the foam pieces

around the legs.

Remove the bag containing the literature.

UNPACKING YOUR DRYER

DRYER

DIMENSIONS

*33-1/4”

(84.5 cm)

Side View

25-1/4” (64.1 cm)

42-13/16” (108.7 cm)

ELECTRICAL CONNECTION

DIMENSIONS POWER CORDS

GE Appliances strongly recommends the use of

factory specified parts. Select the power cord to fit your

installation requirements.

Order on-line at GEApplianceparts.com today,

24 hours a day or by phone at 877.959.8688 during

normal business hours. In Canada, visit your local

GE Appliances parts distributor or call 800.661.1616

or

GEAppliances.ca/en/products/parts-filters-accessories.

Part Number Type Length Amperage

WX9X2 3-Prong 4 Feet 30

WX9X3 3-Prong 5 Feet 30

WX9X4 3-Prong 6 Feet 30

WX9X18 4-Prong 4 Feet 30

WX9X19 4-Prong 5 Feet 30

WX9X20 4-Prong 6 Feet 30

Back

View

30”

(76.2 cm)

20-1/2”

(52.1 cm)

Front

View

23-7/16”

(59.5 cm)

*33-1/4”

(84.5 cm)

ACCESSORIES:

Order on-line at GEApplianceParts.com, 24 hours a day or

by phone at 877.959.8688 during normal business hours.

Part Number Accessory

PM08X10085

Flexible Metal Dryer Transition Duct

49-3000087 Rev 3 13

Installation Instructions

MOBILE OR MANUFACTURED

HOME INSTALLATION

• Installation MUST conform to the

MANUFACTURED HOME CONSTRUCTION

AND SAFETY STANDARD, TITLE 24, PART

3280 or STANDARD FOR MOBILE HOMES

CAN/CSA-Z240 MH, or, when such standards

are not applicable, with AMERICAN NATIONAL

STANDARD FOR MOBILE HOME, ANSI/NFPA

NO. 501B.

• The dryer MUST be vented to the outdoors.

• The exhaust vent MUST be securely fastened to a

non-combustible portion of the mobile home.

• The vent MUST NOT be terminated beneath a

mobile or manufactured home.

• The vent duct material MUST BE METAL.

• KIT 14-D346-33 MUST be used to attach the dryer

securely to the structure.

• The vent MUST NOT be connected to any other

duct, vent or chimney.

• DO NOT use sheet metal screws or other

fastening devices which extend into the interior of

the exhaust vent.

• Provide an opening with a free area of at least 25

square inches for introduction of outside air into

the dryer room.

• See the sections for electrical connection information.

REQUIREMENTS FOR ALCOVE OR

CLOSET INSTALLATION

Keep flammable materials and vapors, such as gasoline,

away from dryer.

Place dryer at least 18” (46 cm) above the floor for a

garage installation.

Failure to do so can result in death, explosion, or fire.

• The dryer MUST be vented to the outdoors.

• Minimum clearance between dryer cabinet and

adjacent walls or other surfaces is:

0” either side

1” front and rear

1” top

• The rear of the dryer should face a wall.

• Consideration must be given to provide adequate

clearance for installation and service.

• Closet doors must be louvered or otherwise

ventilated and have at least 60 square inches of

open area. If the closet contains both a washer

and a dryer, doors must contain a minimum of 120

square inches of open area.

NOTE: WHEN THE EXHAUST DUCT IS LOCATED AT

THE REAR OF THE DRYER, THE CONFIGURATION

OF THE DUCTING MAY REQUIRE GREATER THAN

3” OF REAR CLEARANCE.

MINIMUM CLEARANCE OTHER

THAN ALCOVE OR CLOSET

INSTALLATION

Minimum clearance to combustible surfaces and for

air opening are: 0” both sides, 1” rear and 1” top.

The rear of the dryer should face a wall.

Consideration must be given to provide adequate

clearance for installation and service.

- Explosion Hazard

WARNING

14 49-3000087 Rev 3

Installation Instructions

UNDERCOUNTER INSTALLATION

If an undercounter installation is desired:

• No special dryer installation kit is required.

• If the dryer is installed alone, a minimum of 60

square inches of open area is required. If a washer

and dryer are installed together, a minimum of 120

square inches of open area is required.

BATHROOM OR BEDROOM

INSTALLATION

The installation must conform with local codes or,

in the absence of local codes, with the NATIONAL

ELECTRICAL CODE, ANSI/NFPA NO. 70 (for electric

dryers).

60

square

inches

min.

open

area

Dryer Installed Alone

Countertop and side cabinets

Washer and Dryer Installed Together

Countertop and side cabinets

120

square

inches

min.

open

area

49-3000087 Rev 3 15

Installation Instructions

CONNECTING AN ELECTRIC DRYER

Before making the electrical connection, turn off the

circuit breaker(s) or remove the dryer’s circuit fuse(s) at

the electrical box. Be sure the dryer cord is unplugged

from the wall. NEVER LEAVE THE ACCESS COVER

OFF THE TERMINAL BLOCK.

TOOLS YOU WILL NEED

Ŷ

Slip-joint pliers

Ŷ

Flat-blade

screwdriver

Ŷ

Phillips

screwdriver

Ŷ

Level

Disconnect power supply before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

- Electrical Shock Hazard

WARNING

MATERIALS YOU WILL NEED

Ŷ

Ŷ 4” dia. metal elbow

Ŷ

Ŷ 3/4” Strain relief

(UL recognized)

Ŷ

Ŷ 4” Duct clamps (2) or

4” spring clamps (2)

Ŷ

Ŷ Safety glasses

Ŷ

Ŷ 4” dia. metal duct

(recommended)

Ŷ

Ŷ Gloves

Ŷ

Ŷ Exhaust hood

Ŷ

Ŷ Aluminum foil tape

Ŷ

Ŷ 4” dia., UL-listed

flexible metal duct

(if needed)

Ŷ

Ŷ Dryer power cord kit

(not provided with

dryer)

UL rated 120/240V,

30A with 3 or 4 prongs.

Identify the plug type

as per the house

receptacle before

purchasing line cord.

Ŷ

Ŷ 4” Cover Plate

(Kit WE49X22606)

(if needed)

Stacking installations

may require a power

cord up to 6 feet in

length.

RECEPTACLE FOR CONNECTION

TO SPECIFIED WASHERS

Receptacle

Not a general-use

receptacle – For use

with washers

GFW148, QFW150,

GFQ14, or GNW128

only.

NOTE: An auxiliary

cover may be present

on some models.

Remove the auxiliary

cover if connecting

washer models

GFQ14 or GNW128.

16 49-3000087 Rev 3

For direct wire connections:

Use 10 gauge copper wire.

Use a UL-listed strain relief.

Disconnect power before making electrical connections.

Connect neutral wire (white or center wire) to center

terminal.

Ground wire (green or bare wire) must be connected to

green ground connector.

Connect remaining two supply wires to remaining two

terminals.

Securely tighten all electrical connections.

Replace the terminal block cover.

Failure to do so can result in death, fire or electrical shock.

GROUNDING INSTRUCTIONS

For a permanently connected dryer: This dryer

must be connected to a grounded metal, permanent

wiring system, or an equipment-grounding conductor

must be run with the circuit conductors and

connected to the equipment-grounding terminal on

the appliance.

Improper connection of the

equipment-grounding conductor can

result in a risk of electric shock. Check with a qualified

electrician, or service representative or personnel, if

you are in doubt as to whether the appliance is properly

grounded.

SAVE THESE INSTRUCTIONS

- Fire Hazard

WARNING

Use a new UL-listed 240V 30 amp dryer power supply

cord with closed ring terminals or spade terminals with

upturned ends.

Use a UL-listed strain relief.

Disconnect power before making electrical connections.

Connect neutral wire (white or center wire) to center

terminal.

Ground wire (green or bare wire) must be connected to

green ground connector.

Connect remaining two supply wires to remaining two

terminals.

Securely tighten all electrical connections.

Replace the terminal block cover.

Failure to do so can result in death, fire or electrical shock.

For electrical connections using a

power cord:

GROUNDING INSTRUCTIONS

For a grounded, cord-connected dryer: This dryer

must be grounded. In the event of a malfunction or

breakdown, grounding will reduce the risk of electric

shock by providing a path of least resistance for

electric current. This dryer uses a cord having an

equipment-grounding conductor and a grounding

plug. The plug must be plugged into an appropriate

outlet that is properly installed and grounded in

accordance with all local codes and ordinances.

Improper connection of the

equipment-grounding conductor can

result in a risk of electric shock. Check with a qualified

electrician, or service representative or personnel, if

you are in doubt as to whether the appliance is properly

grounded. DO NOT modify the plug on the power supply

cord. If it will not fit the outlet, have a proper outlet

installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

- Fire Hazard

WARNING

ELECTRICAL CONNECTION

INFORMATION FOR ELECTRIC

DRYERS

ELECTRICAL CONNECTION

INFORMATION FOR ELECTRIC

DRYERS

Installation Instructions

TO PREVENT ELECTRIC SHOCK, DISCONNECT

POWER BEFORE SERVICING.

This dryer should be connected to an individual branch

circuit with 10 gauge copper wire minimum through a

30 amp fuse or circuit breaker. DO NOT fuse neutral.

Use copper conductors only.

- Electrical Shock Hazard

WARNING

TO PREVENT ELECTRIC SHOCK, DISCONNECT

POWER BEFORE SERVICING.

This dryer should be connected to an individual branch

circuit with 10 gauge copper wire minimum through a

30 amp fuse or circuit breaker. DO NOT fuse neutral.

Use copper conductors only.

- Electrical Shock Hazard

WARNING

49-3000087 Rev 3 17

Installation Instructions

CONNECTING DRYER USING

3-WIRE CONNECTION

CONNECTING DRYER USING

4-WIRE CONNECTION (MUST

BE USED FOR MOBILE HOME

INSTALLATION)

NOTE: Since January 1, 1996, the National Electrical

Code requires that new constructions use a 4-wire

connection to an electric dryer. A 4-wire cord must

also be used where local codes do not permit grounding

through the neutral. 3-wire connection is NOT for use

on new construction.

1. Turn off the circuit breaker(s) (30 amp) or remove

the dryer’s circuit fuse at the electrical box.

2. Be sure the dryer cord is unplugged from the wall

receptacle.

3. Remove the power cord cover located at the upper

back.

4. Remove green ground screw and retain for use in

Step 7. Remove center screw (marked N) in terminal

block. Remove and discard ground strap.

5. Install 3/4 in. UL-recognized strain relief to power

cord entry hole. Bring power cord through strain

relief and bracket.

6. Connect power cord as follows:

A. Connect the 2 hot lines to the outer screws of the

terminal block (marked L1 and L2).

B. Connect the neutral (white) line to the center of

the terminal block (marked N).

7. Attach ground wire of power cord with the green

ground screw (hole above strain relief bracket).

Tighten all terminal block screws (3) securely.

8. Properly secure power cord to strain relief and

bracket.

9. Reinstall the cover.

NEVER LEAVE THE COVER OFF OF THE

TERMINAL BLOCK.

NEVER LEAVE THE COVER OFF OF THE

TERMINAL BLOCK.

3-wire Connection

Not for use in Canada.

DO NOT use for Mobile Home Installations.

NOT for use on new construction.

NOT for use on recreational vehicles.

NOT for use in areas where local codes prohibit

grounding through the neutral conduction.

1. Turn off the circuit breaker(s) (30 amp) or remove

the dryer’s circuit fuse at the electrical box.

2. Be sure the dryer cord is unplugged from the wall

receptacle.

3. Remove the power cord cover located at the upper

back.

4. Install 3/4-in. UL-recognized strain relief to power

cord entry hole. Bring power cord through strain

relief and bracket.

5. Connect power cord as follows:

A. Connect the 2 hot lines to the outer screws of

the terminal block (marked L1 and L2).

B. Connect the neutral (white) line to the center of

the terminal block (marked N).

6. Be sure ground strap is connected to green ground

screw on cabinet rear. Tighten all terminal block

screws (3) securely.

7. Properly secure power cord to strain relief and

bracket.

8. Reinstall the cover.

L1 NL2

Green wire

from power

cord

3/4” Strain

Relief and

Bracket

Cover

4 #10 AWG minimum copper conductors or 120/240V 30A

power supply cord kit marked for use with dryers and provided

with closed loop or spade terminals with upturned ends (not

supplied).

White Wire

Black

or Red

Wire

Black

or

Red

Wire

If required, by local code, install external ground (not

provided) to grounded metal, cold water pipe, or other

established ground determined by a qualified electrician.

L1 NL2

Black or Red Wire

3/4” Strain

Relief and

Bracket

Cover

3 #10 AWG minimum copper conductors or 120/240V 30A

power supply cord kit marked for use with dryers and provided

with closed loop or spade terminals with upturned ends (not

supplied).

Ground

Strap

White Wire

Black

or Red

Wire

18 49-3000087 Rev 3

Installation Instructions

EXHAUSTING THE DRYER

TOOLS AND MATERIALS YOU WILL

NEED TO INSTALL EXHAUST DUCT

CONNECTING THE DRYER TO

HOUSE VENT

RIGID METAL TRANSITION DUCT

• For best drying performance, a rigid metal transition

duct is recommended.

• Rigid metal transition ducts reduce the risk of

crushing and kinking.

UL-LISTED FLEXIBLE METAL CLOTHES

DRYER TRANSITION DUCT

• If rigid metal cannot be used, then UL-listed flexible

metal clothes dryer transition duct (GE Appliances

part – PM08X10085) can be used.

• Never install transition duct in walls, ceilings, floors

or other enclosed spaces.

• Total length of transition duct should not exceed 8’

(2.4 m).

• For many applications, installing elbows at both

the dryer and the wall is highly recommended (see

illustrations in next section). Elbows allow the dryer

to sit close to the wall without kinking and/or crushing

the transition duct, maximizing drying performance.

• Avoid resting the duct on sharp objects.

UL-LISTED FLEXIBLE METAL (FOIL-TYPE)

TRANSITION DUCT

• In special installations, it may be necessary to

connect the dryer to the home exhaust vent

using flexible metal (foil-type) transition duct. UL–

LISTED universal flexible dryer transition duct

(GE Appliances parts – PM8X73 or WX8X73)

may be used ONLY in installations where rigid

metal or flexible metal transition ducting cannot be

used AND where a 4” diameter can be maintained

throughout the entire length of the transition duct.

• In Canada and the United States, only transition

ducts that comply with “UL 2158A STANDARD

FOR CLOTHES DRYER TRANSITION DUCT”

shall be used.

• Avoid resting the duct on sharp objects.

• For best drying performance:

1. Slide one end of the duct over the clothes

dryer outlet pipe.

2. Secure the duct with a clamp.

3. With the dryer in its permanent position,

extend the duct to its full length. Allow 2”

of duct to overlap the exhaust pipe. Cut off

and remove excess duct. Keep the duct as

straight as possible for maximum airflow.

4. Secure the duct to the exhaust pipe with the

other clamp.

Ŷ

Ŷ Phillips-head

screwdriver

Ŷ

Ŷ Aluminum foil

tape or duct

clamp

Ŷ

Ŷ Rigid or UL-listed flexible

metal 4” (10.2 cm) duct

Ŷ

Ŷ Drill with 1/8” drill bit

(for bottom venting)

Ŷ

Ŷ Hacksaw

Ŷ

Ŷ Vent

hood

This dryer MUST be vented to the outdoors.

Use only 4” rigid metal ducting for the home

exhaust duct.

Use only 4" rigid metal, UL-listed flexible

metal, or UL-listed metal foil dryer transition

duct to connect the dryer to the home exhaust.

DO NOT use any plastic to vent the dryer,

this includes the home exhaust duct, dryer

transition duct, or within the dryer.

DO NOT use flexible metal or metal foil ducting

for a home exhaust duct or within the dryer.

DO NOT exhaust into a chimney, kitchen

exhaust, gas vent, wall, ceiling, attic, crawl

space, or concealed space of a building.

DO NOT install a screen in or over the exhaust

duct.

DO NOT install a booster fan in the exhaust duct.

DO NOT use duct longer than specified in the

exhaust length table.

Failure to follow these instructions can result in

death or fire.

PARTS AVAILABLE FROM

GEAPPLIANCEPARTS.COM OR

LOCAL SERVICE ORGANIZATIONS

PM8X85

Outdoor exhaust hood

PM08X10085

8’ Flexible metal clothes dryer transition

duct with 2 clamps

WX08X10130

4” Dryer exhaust clamp

WE49X22606

Rear exhaust opening cover, for side or

bottom vented dryers

- Fire Hazard

WARNING

49-3000087 Rev 3 19

Installation Instructions

EXHAUSTING THE DRYER (cont.)

Using exhaust longer than specified length will:

• Increase the drying times and the energy cost.

• Reduce the dryer life.

• Accumulate lint, creating a potential fire hazard.

The correct exhaust installation is YOUR

RESPONSIBILITY.

Problems due to incorrect installation are not

covered by the warranty.

The MAXIMUM ALLOWABLE length of the exhaust

system depends upon the type of duct, number of turns,

the type of exhaust hood (wall cap) and all conditions

noted on the chart.

• Internal elbows added for side or bottom vent

conversions must be included in the total elbow count.

• Any elbow greater than 45° should be treated as a 90°

elbow; one elbow of 45° or less may be ignored.

• Two 45° elbows will be treated like one 90° elbow.

• For the side exhaust installations, add one 90° elbow to

the chart.

• For every additional 90° elbow, reduce the allowable

vent system length by 10 feet.

• When calculating the total vent system length, you

must add all the straight portions and elbows of the

system (including the transition duct).

EXHAUST LENGTH

EXHAUST

LENGTH

RECOMMENDED MAXIMUM LENGTH

Exhaust Hood Types

Recommended Use only for short run

installations

4" DIA.

4"

4" DIA.

2-1/2"

No. of 90° Elbows Rigid Metal Rigid Metal

0 90 Feet 60 Feet

1 60 Feet 45 Feet

2 45 Feet 35 Feet

3 35 Feet 25 Feet

4 25 Feet 15 Feet

• DO NOT bend

or collapse

ducting.

Use elbows

if turns are

necessary.

• DO NOT use

excessive

exhaust

length. Cut

duct as short

as possible.

• DO NOT

crush duct

against

the wall.

• DO NOT

set dryer

on duct.

• DO cut duct as short

as possible and

install straight into

wall.

• DO use elbows

when turns are

necessary.

Elbows

20 49-3000087 Rev 3

Installation Instructions

BEFORE YOU BEGIN

• Remove and discard existing plastic or metal foil

duct and replace with UL-listed duct.

• Remove any lint from the wall exhaust opening.

Internal

Duct

Opening

Wall

Check that exhaust

hood damper

opens and closes

freely.

STANDARD REAR EXHAUST

NOTE: We strongly recommend using rigid metal

exhaust duct. However, if flexible ducting is used it

must be UL-Listed metal, not plastic.

• For straight line installation, connect the dryer

exhaust to the external exhaust hood using aluminum

foil tape or clamp.

RECOMMENDED CONFIGURATION

TO MINIMIZE EXHAUST BLOCKAGE

Using duct elbows will prevent duct kinking and

collapsing.

EXHAUST SYSTEM CHECKLIST

HOOD OR WALL CAP

• Terminate in a manner to prevent back drafts or entry of

birds or other wildlife.

• Termination should present minimal resistance to

the exhaust airflow and should require little or no

maintenance to prevent clogging.

• Wall caps must be installed at least 12” above ground

level or any other obstruction with the opening pointed

down.

SEPARATION OF TURNS

• For best performance, separate all turns by at least

4 ft. of straight duct, including distance between

last turn and dampened exhaust hood (wall cap).

SEALING OF JOINTS

• All joints should be tight to avoid leaks. The male end

of each section of duct must point away from the dryer.

• Duct joints should be made air- and moisture-tight

by wrapping the overlapped joints with aluminum

foil tape.

• Do not assemble ductwork with any fasteners that

extend into the duct. These fasteners can accumulate

lint, creating a potential fire hazard.

• Horizontal runs should slope down towards the

outdoors 1/4” per foot.

• Provide an access for inspection and cleaning of

the exhaust system, especially at turns and joints.

Exhaust system shall be inspected and cleaned at

least once a year.

INSULATION

• Ductwork that runs through an unheated area or is

near air conditioning should be insulated to reduce

condensation and lint build-up.

Wall Side

Dryer

Side

Aluminum Foil Tape

EXHAUSTING THE DRYER (cont.)

Duct

Transition

Ducting

Wall

We recommend that you install your dryer before

installing your washer. This will permit direct

access for easier exhaust connection.

Slide the end of the exhaust duct on the back of the

dryer and secure with aluminum foil tape or a hose

clamp.

La page charge ...

GE GFD14ESSNWW Le manuel du propriétaire

GE GFD14ESSNWW Le manuel du propriétaire

dans d''autres langues