Yamaha Tio1608 Le manuel du propriétaire

Marque: Yamaha

Modèle: Tio1608

Catégorie: Matériel musical

Taper: Le manuel du propriétaire

Ce manuel convient également à

Owner’s Manual

Benutzerhandbuch

Mode d’emploi

Manual de instrucciones

Manual do Proprietário

Manuale di istruzioni

Ɋɭɤɨɜɨɞɫɬɜɨɩɨɥɶɡɨɜɚɬɟɥɹ

EnglishDeutschFrançaisEspañolPortuguêsItalianoɊɭɫɫɤɢɣ

AUDIO INTERFACE / INTERFACE AUDIO

INTERFAZ DE AUDIO / INTERFACE DE ÁUDIO

ȺɍȾɂɈɂɇɌȿɊɎȿɃɋ

Owner’s Manual

Tio1608-D2

Explanation of Graphical Symbols

Explication des symbols

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated

“dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

L’éclair avec une flèche à l’intérieur d’un triangle équilatéral est destiné à attirer l’attention de l’utilisateur sur la présence d’une «

tension dangereuse » non isolée à l’intérieur de l’appareil, pouvant être suffisamment élevée pour constituer un risque d’électrocution.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance

(servicing) instructions in the literature accompanying the product.

Le point d’exclamation à l’intérieur d’un triangle équilatéral est destiné à attirer l’attention de l’utilisateur sur la présence d’instructions

importantes sur l’emploi ou la maintenance (réparation) de l’appareil dans la documentation fournie.

IMPORTANT SAFETY

INSTRUCTIONS

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in accordance with

the manufacturer’s instructions.

8 Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that

produce heat.

9 Do not defeat the safety purpose of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than the

other. A grounding type plug has two blades and a third grounding

prong. The wide blade or the third prong are provided for your

safety. If the provided plug does not fit into your outlet, consult an

electrician for replacement of the obsolete outlet.

10 Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

11 Only use attachments/accessories specified by the manufacturer.

12 Use only with the cart, stand, tripod, bracket, or

table specified by the manufacturer, or sold

with the apparatus. When a cart is used, use

caution when moving the cart/apparatus

combination to avoid injury from tip-over.

13 Unplug this apparatus during lightning storms

or when unused for long periods of time.

14 Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way, such

as power-supply cord or plug is damaged, liquid has been spilled

or objects have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally, or has

been dropped.

PRÉCAUTIONS

CONCERNANT LA SÉCURITÉ

1 Lire ces instructions.

2 Conserver ces instructions.

3 Tenir compte de tous les avertissements.

4 Suivre toutes les instructions.

5 Ne pas utiliser ce produit à proximité d’eau.

6 Nettoyer uniquement avec un chiffon propre et sec.

7 Ne pas bloquer les orifices de ventilation. Installer l’appareil

conformément aux instructions du fabricant.

8 Ne pas installer l’appareil à proximité d’une source de chaleur

comme un radiateur, une bouche de chaleur, un poêle ou tout

autre appareil (y compris un amplificateur) produisant de la

chaleur.

9 Ne pas modifier le système de sécurité de la fiche polarisée ou de

la fiche de terre. Une fiche polarisée dispose de deux broches dont

une est plus large que l’autre. Une fiche de terre dispose de deux

broches et d’une troisième pour le raccordement à la terre. Cette

broche plus large ou cette troisième broche est destinée à assurer

la sécurité de l’utilisateur. Si la fiche équipant l’appareil n’est pas

compatible avec les prises de courant disponibles, faire remplacer

les prises par un électricien.

10 Acheminer les cordons d’alimentation de sorte qu’ils ne soient pas

piétinés ni coincés, en faisant tout spécialement attention aux

fiches, prises de courant et au point de sortie de l’appareil.

11 Utiliser exclusivement les fixations et accessoires spécifiés par le

fabricant.

12 Utiliser exclusivement le chariot, le stand, le

trépied, le support ou la table recommandés par

le fabricant ou vendus avec cet appareil. Si

l’appareil est posé sur un chariot, déplacer le

chariot avec précaution pour éviter tout risque

de chute et de blessure.

13 Débrancher l’appareil en cas d’orage ou

lorsqu’il doit rester hors service pendant une période prolongée.

14 Confier toute réparation à un personnel qualifié. Faire réparer

l’appareil s’il a subi tout dommage, par exemple si la fiche ou le

cordon d’alimentation est endommagé, si du liquide a coulé ou

des objets sont tombés à l’intérieur de l’appareil, si l’appareil a été

exposé à la pluie ou à de l’humidité, si l’appareil ne fonctionne pas

normalement ou est tombé.

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

ATTENTION :

POUR RÉDUIRE LES RISQUES D'ÉLECTROCUTION, NE PAS RETIRER

LE CAPOT (OU LE DOS). NE CONTIENT PAS DE PIÈCES NÉCESSITANT

L'INTERVENTION DE L'UTILISATEUR. POUR TOUTE INTERVENTION,

FAIRE APPEL À DES PROFESSIONNELS QUALIFIÉS.

ATTENTION

RISQUE DE CHOC

ELECTRIQUE-NE PAS OUVRIR

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT

EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

AVERTISSEMENT

POUR RÉDUIRE LES RISQUES D’INCENDIE OU DE DÉCHARGE

ÉLECTRIQUE, N’EXPOSEZ PAS CET APPAREIL À LA PLUIE OU À

L’HUMIDITÉ.

(502-M01 UL 60065-1 01)

Owner’s Manual

Tio1608-D2

FCC INFORMATION (U.S.A.)

(529-M04 FCC class B YCA 02)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!

This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not

expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s

supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC

authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class “B”

digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a

residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio

frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to

the operation of other electronic devices. Compliance with FCC regulations does not guarantee that interference will not occur in all

installations. If this product is found to be the source of interference, which can be determined by turning the unit “OFF” and “ON”,

please try to eliminate the problem by using one of the following measures:

- Relocate either this product or the device that is being affected by the interference.

- Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.

- In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-

in to co-axial type cable.

If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of

product. If you cannot locate the appropriate retailer, please contact Yamaha Corporation of America, 6600 Orangethorpe Avenue,

Buena Park, CA 90620, U.S.A.

The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.

COMPLIANCE INFORMATION STATEMENT

(Supplier’s declaration of conformity procedure)

Responsible Party : Yamaha Corporation of America

Address : 6600 Orangethorpe Avenue, Buena Park, CA. 90620, U.S.A.

Telephone : 714-522-9011

Type of Equipment : AUDIO INTERFACE

Model Name : Tio1608-D2

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received, including interference that may cause undesired operation.

(529-M02 FCC sdoc YCA 02)

Owner’s Manual

Tio1608-D2

Table of contents

Owner’s Manual

Tio1608-D2

English

Table of contents

Included items......................................................... 5

PRECAUTIONS ........................................ 6

Introduction .......................................... 8

Updating the firmware ............................................ 8

Dante support......................................................... 8

Precautions when rackmounting ............................. 8

Recessed Installation................................................ 8

Device features...................................... 9

Front panel.............................................................. 9

Rear panel ............................................................. 11

Connection methods ........................... 14

Quick Config (automatic setup)............................. 14

Manual setup ........................................................ 15

Head amp control ................................................. 15

Troubleshooting.................................. 16

Troubleshooting.................................................... 16

How to read the indicators ................. 17

Specifications .................................... 121

General Specifications ......................................... 121

Input Output Digital I/O Character...................... 122

Dimensions ......................................................... 123

Included items

•Owner's Manual (this document)

•Power cord

•Rubber feet ×4

NOTE

The rubber feet included in this package can be attached to the

product to prevent slippage when it is to be used on a slippery

surface.

Information for users on collection

and disposal of old equipment:

This symbol on the products,

packaging, and/or accompanying

documents means that used

electrical and electronic products

should not be mixed with general

household waste. For proper

treatment, recovery and recycling

of old products, please take them

to applicable collection points, in accordance with

your national legislation.

By disposing of these products correctly, you will

help to save valuable resources and prevent any

potential negative effects on human health and the

environment which could otherwise arise from

inappropriate waste handling.

For more information about collection and recycling

of old products, please contact your local

municipality, your waste disposal service or the

point of sale where you purchased the items.

For business users in the European Union:

If you wish to discard electrical and electronic

equipment, please contact your dealer or

supplier for further information.

Information on Disposal in other Countries

outside the European Union:

This symbol is only valid in the European Union.

If you wish to discard these items, please contact

your local authorities or dealer and ask for the

correct method of disposal.

(58-M02 WEEE en 01)

Owner’s Manual

Tio1608-D2

PA_en_14 1/2

PRECAUTIONS

PLEASE READ CAREFULLY

BEFORE PROCEEDING

Please keep this manual in a safe place for

future reference.

WARNING

Always follow the basic precautions listed below to

avoid the possibility of serious injury or even death

from electrical shock, short-circuiting, damages, fire

or other hazards. These precautions include, but are

not limited to, the following:

If you notice any abnormality

•If any of the following problems occur, immediately turn off

the power switch and disconnect the electric plug from the

outlet.

-The power cord or plug becomes frayed or damaged.

-Unusual smells or smoke are emitted.

-Some object, or water has been dropped into the product.

-There is a sudden loss of sound during use of the

product.

-Cracks or other visible damage appear on the product.

Then have the product inspected or repaired by qualified

Yamaha service personnel.

Power supply

•Do not place the power cord near heat sources such as

heaters or radiators, and do not excessively bend or

otherwise damage the cord, place heavy objects on it, or

place it in a position where anyone could walk on, trip over,

or roll anything over it.

•Only use the voltage specified as correct for the product.

The required voltage is printed on the name plate of the

product.

•Use the supplied power cord/plug only.

If you intend to use the product in an area other than in the

one you purchased, the included power cord may not be

compatible. Please check with your Yamaha dealer.

•Do not use the supplied cord/plug for other products.

•Check the electric plug periodically and remove any dirt or

dust which may have accumulated on it.

•Make sure to fully insert the electric plug to prevent electric

shocks or fire.

•When setting up the product, make sure that the AC outlet

you are using is easily accessible. If some trouble or

malfunction occurs, immediately turn off the power switch

and disconnect the plug from the outlet. Even when the

power switch is turned off, as long as the power cord is not

unplugged from the wall AC outlet, the product will not be

disconnected from the power source.

•Remove the electric plug from the outlet when the product

is not to be used for extended periods of time.

•Do not touch the product or the electric plug during an

electrical storm.

•Be sure to connect to an appropriate outlet with a

protective grounding connection. Improper grounding can

result in electrical shock, fire, or damage.

Do not open

•This product contains no user-serviceable parts. Do not

attempt to disassemble the internal parts or modify them in

any way.

Water warning

•Do not expose the product to rain, use it near water or in

damp or wet conditions, or place on it any containers (such

as vases, bottles or glasses) containing liquids which might

spill into any openings.

•Never insert or remove an electric plug with wet hands.

Fire warning

•Do not place any burning items or open flames near the

product, since they may cause a fire.

Hearing loss

•Before turning the power of all devices on or off, make sure

that all volume levels are set to the minimum. Failing to do

so may result in hearing loss, electric shock, or device

damage.

•When turning on the AC power in your audio system,

always turn on the power amplifier LAST, to avoid hearing

loss and speaker damage. When turning the power off, the

power amplifier should be turned off FIRST for the same

reason.

CAUTION

Always follow the basic precautions listed below to

avoid the possibility of physical injury to you or

others. These precautions include, but are not limited

to, the following:

Power supply

•When removing the electric plug from the product or an

outlet, always hold the plug itself and not the cord. Pulling

by the cord can damage it.

Location and connection

•Do not place the product in an unstable position or a

location with excessive vibration, where it might

accidentally fall over and cause injury.

•Keep this product out of reach of children. This product is

not suitable for use in locations where children are likely to

be present.

•Do not block the vents. This product has ventilation holes at

the front/rear/sides to prevent the internal temperature from

becoming too high. In particular, do not place the product

on its side or upside down. Inadequate ventilation can

result in overheating, possibly causing damage to the

product(s), or even fire.

•If the product is mounted in an EIA standard rack, carefully

read the section "Precautions when rackmounting" on page

8. Inadequate ventilation can result in overheating, possibly

causing damage to the product(s), malfunction, or even fire.

Owner’s Manual

Tio1608-D2

English

PA_en_14 2/2

•Do not place the product in a location where it may come

into contact with corrosive gases or salt air. Doing so may

result in malfunction.

•Before moving the product, remove all connected cables.

Maintenance

•Remove the power plug from the AC outlet when cleaning

the product.

Handling caution

•Do not insert your fingers or hands in any gaps or openings

on the product (vents, panel, etc.).

•Do not rest your weight on the product or place heavy

objects on it.

NOTICE

To avoid the possibility of malfunction/damage to the

product, damage to data, or damage to other property,

follow the notices below.

Handling and maintenance

• Do not use the product in the vicinity of a TV, radio, or other

electric products. Otherwise, the product, TV, or radio may

generate noise.

• Do not expose the product to excessive dust or vibration, or

extreme cold or heat, in order to prevent the possibility of

panel disfiguration, unstable operation, or damage to the

internal components.

• Do not install in locations where temperature changes are

severe. Otherwise, condensation may form on the inside or

the surface of the product, causing it to break.

• If there is reason to believe that condensation might have

occurred, leave the product for several hours without turning

on the power until the condensation has completely dried

out, in order to prevent possible damage.

• Do not place vinyl, plastic or rubber objects on the product,

since this might cause alteration or discoloration of the

panel.

• Clean the product with a dry and soft cloth. Do not wipe

product surfaces with sodium hypochlorite, alcohol,

benzene, paint thinners, cleaning fluids, or a chemical-

impregnated wiping cloth, which could cause discoloration

or change surface characteristics.

Information

About copyrights

• Copying of the software or reproduction of this manual in

whole or in part by any means is expressly forbidden

without the written consent of the manufacturer.

Protection of copyright

• Do not use this product for any purpose that may infringe

upon the rights of any third party including copyrights, as

established by law in each country or region.

• Yamaha bears no responsibility for any infringement upon

third party rights that may occur as a result of using this

product.

About functions/data bundled with the

product

• This product uses the Dante module provided by

Audinate.The Dante module used in this product can be

confirmed in Dante Controller.

For more information about the open source licenses used

for each Dante module, please visit Audinate's website.

https://www.audinate.com/software-licensing

• XLR-type connectors are wired as follows (IEC60268

standard): pin 1: ground, pin 2: hot (+), and pin 3: cold (-).

About this manual

• The illustrations and screens as shown in this manual are

for instructional purposes only.

• Yamaha Corporation makes no representations or

warranties with regard to the use of the software and

documentation and cannot be held responsible for the

results of the use of this manual and the software.

• The company names and product names in this manual are

the trademarks or registered trademarks of their respective

companies.

•Software may be revised and updated without prior notice.

About disposal

• This product contains recyclable components.

When disposing of this product, please contact the

appropriate local authorities.

Yamaha cannot be held responsible for damage caused

by improper use or modifications to the product, or data

that is lost or destroyed.

Introduction

Owner’s Manual

Tio1608-D2

Introduction

Thank you for purchasing the Yamaha Tio1608-D2 I/O rack.

The Tio1608-D2 is an I/O rack that features 16 channels of

analog inputs and 8 channels of analog outputs.

In order to take full advantage of this product's features, and

to enjoy years of trouble-free use, please read this

document before you begin using the product. After you

have read this document, please keep it in a safe place.

Updating the firmware

The firmware contained in this product can be updated to

take advantage of new features, feature improvements, and

bug fixes. The product uses two types of firmware.

•Main unit firmware

•Dante module firmware

Details about updating the firmware are available online.

https://www.yamahaproaudio.com/

For information about updating and setting up the console,

please refer to the firmware update guide available on the

website.

Dante support

This product uses the Dante digital audio network protocol

to send and receive audio signals. Dante is a protocol

developed by Audinate that is designed to deliver

multichannel audio signals at various sampling and bit

rates, as well as device control signals over a Gigabit

Ethernet network.

For information about Dante, please visit the Audinate

website.

http://www.audinate.com/

You can also find information about Dante and Dante-

compatible products on the Yamaha Pro Audio website.

https://www.yamahaproaudio.com/

Precautions when rackmounting

This product is designed to function in environments with a

temperature of 0 to 40°C. If you install this product together

with multiple units of the same device or other devices in a

standard EIA rack, the heat produced by the devices may

raise the ambient temperature inside the rack enclosure to

the point where performance is affected. To ensure that the

heat produced by this product can be dissipated

appropriately, please ensure the following conditions when

rackmounting it.

• When mounting the unit in a rack with devices such as

power amplifiers that generate a significant amount of

heat, leave at least 1U of unused space between the unit

and the other device.

Additionally, install a ventilation panel in this unused

space or leave it open to ensure adequate cooling.

• To ensure sufficient airflow, leave the back of the rack

open and position it at least 10 centimeters from walls or

other surfaces.

If the back of the rack cannot be left open, install a

commercially available fan or similar ventilating option to

secure sufficient airflow.

If you install a fan kit, there may be cases in which closing

the back of the rack will produce a greater cooling effect.

Refer to the documentation included with the rack and/or

fan unit details.

Recessed Installation

If you want to recess the front panel surface of the device

from the front edge of the rack, you can adjust the position

of the rack mount brackets to recess the device by 50mm,

as shown in the illustration below.

NOTE

When updating this product's Dante module firmware, make sure

you also update the Dante module firmware contained in other

connected devices.

NOTE

Please do not use the EEE function (*) of network switches in a

Dante network.

The EEE function may deteriorate the clock synchronization

performance and interrupting audio.

Therefore we strongly recommend that:

• If you use managed switches, ensure that they allow EEE to be

disabled. Make sure that EEE is disabled on all ports used for

real-time Dante traffic.

• If you use unmanaged switches, make sure to not use network

switches that support the EEE function, since EEE operation

cannot be disabled in these switches.

*EEE (Energy Efficient Ethernet) is a technology that reduces

switch power consumption during periods of low network traffic.

It is also known as Green Ethernet and IEEE802.3az.

NOTE

When you install the brackets, use the same screws that you just

removed.

50 mm

Device features

Owner’s Manual

Tio1608-D2

English

Device features

Front panel

[INPUT] 1–16

Combination connectors that support both XLR 3-pin

cable connectors and TRS phone plug. Use these

connectors to connect mics and instruments.

Nominal input level is -62 dBu to +10 dBu.

When connecting a cable that uses an XLR 3-pin cable

connector, make sure you supply +48 V phantom

power to any devices that require it.

[+48V]

These indicators light when +48 V phantom power is

turned on for the corresponding input channels. You

can use a compatible mixing console or other device

to turn phantom power on and off If the [+48V

ACTIVE] is turned off, no phantom power will be

supplied even if phantom power is turned on for

individual channels (although the [+48V] will still

flash).

[OUTPUT +4dBu] 1–8

These XLR 3-pin chassis balanced connectors deliver

analog output from the unit’s corresponding output

channels. Nominal output level is +4 dBu.

[STATUS INPUT]

This indicator indicates the status of the signal being

input to the analog input connectors.

If the signal input to any channel reaches or exceeds

-34 dBFS, the indicator lights in green; if the signal

reaches or exceeds -3 dBFS, the indicator lights in red.

The indicator flashes in red if the input is muted, if the

system clock is being synced, or if there is a system

error.

[STATUS OUTPUT]

If the signal level of any analog output connector

reaches or exceeds -34 dBFS, this indicator lights in

green.

The indicator flashes in red if the output is muted, if

the system clock is being synced, or if there is a system

error.

[UNIT ID]

Determines the unit's identifier (i.e., unit ID) when

using Quick Config. When using multiple units, set a

unique ID (1–3) to each unit.

When not using Quick Config, this switch and the DIP

switches on the rear of the unit determine the ID.

(page 11)

Turn the unit off before changing the [UNIT ID]

position. If you move the switch while the unit is

turned on, the new switch position is not applied.

See "Connection methods" (page 14) for information

about Quick Config.

ղձ մյնշոչպջռճ

NOTE

The PAD will be switched on or off internally when the analog

gain of the internal head amp is adjusted between +17dB and

+18dB. When using phantom power, noise may be generated

if there is a difference in the impedance between the hot and

cold of the device connected to an input connector.

CAUTION

• Make sure that phantom power is turned off unless it is

needed.

• When turning on phantom power, make sure that no

equipment other than phantom-powered devices such

condenser microphones are connected to the corresponding

[INPUT] connectors. Supplying phantom power to a device

that does not require it can damage the device.

• Do not connect or disconnect a device while phantom power

is being supplied to it. Doing so can damage the connected

device and the unit itself.

• To prevent damage to speakers, make sure that power

amplifiers and powered speakers are turned off when turning

phantom power on or off. We also recommend setting all

digital mixing console output controls to their minimum

settings when turning phantom power on or off. Sudden high-

volume sound caused by turning phantom power on or off

could damage equipment and hearing.

NOTICE

If this product's balanced outputs are connected to an

unbalanced audio source, a difference in ground potential could

cause a malfunction. Make sure each device has the same

ground potential. The cable used to connect an unbalanced

device should be pin 1: ground, pin 3: cold.

NOTE

If TF Quick Config or DM3 Auto Setup functionality is used in

a system with a combination of Tio1608-D2 and older

Tio1608-D models, make sure Tio1608-D2 UNIT ID settings

do not conflict with Tio1608-D UNIT ID settings either.

Device features

Owner’s Manual

Tio1608-D2

[QUICK CONFIG FOR TF]

Turns Quick Config on and off.

Set this switch setting to OFF if Quick Config is not used

or multiple mixers are connected via a network.

Turn the unit off before changing the [QUICK CONFIG

FOR TF] position. If this setting is set while the power

is ON, it is not applied in the main unit until the power

is switched OFF and ON.

See "Connection methods" (page 14) for information

about Quick Config.

[SYSTEM]

Indicate the status of the Tio1608-D2.

During normal operation, the green indicator is lit and

the red indicator is off. When the unit is turned on, if

the green indicator is off and the red indicator is lit or

is flashing, an error has occurred. For more

information, see "How to read the indicators". (page

17)

[SYNC]

Indicate the status of the unit's internal Dante clock

sync.

When the green indicator is lit, the unit is the clock

follower, and the clock is in sync. When the green

indicator is flashing, the unit is the clock leader. When

the unit is turned on, the green indicator should either

light or flash; if the indicator is off, an error has

occurred. For more information, see "How to read the

indicators". (page 17-18)

[+48V ACTIVE]

Turns the unit's +48 V phantom power on and off. If

the [+48V ACTIVE] is off, no phantom power is

supplied to the input connectors even if phantom

power is turned on for individual inputs. In this case,

the [+48V] for individual inputs will still light, even

though no phantom power will be supplied.

You can change the switch position while the unit is

turned on.

Power indicator

Indicates whether the unit is turned on or off.

Power switch

Turns the unit on and off.

NOTICE

Rapidly turning the unit on and off in succession can cause it to

malfunction. After turning the unit off, wait for about 6 seconds

before turning it on again.

Device features

Owner’s Manual

Tio1608-D2

English

Rear panel

[AC IN]

Connect the included power cord. When connecting

to a power outlet, first connect the power cord to the

unit, then connect the power cord to the power

outlet.

Cooling vent

The Tio1608-D2 contains a cooling fan. The cooling

air is exhausted here, so please be careful not to block

this vent. The air is taken in through the ventilation

ports at the front.

[FAN]

Allows you to set the unit's internal cooling fan to run

at high or low speed. The switch is set at the factory

to [LOW], but as long as the unit is operated within

the specified ambient temperature range either the

[LOW] or [HIGH] setting can be used. The [HIGH]

setting is recommended if the ambient temperature is

high, if the unit is in direct sunlight (even if the

ambient temperature is within the specified operating

range), and in any situation in which fan noise is not a

problem. When mounting three or more units without

leaving space between each unit, set each unit's fan

speed to HIGH.

You can change the switch position while the unit is

turned on.

DIP switches

Determines the unit's start up mode.

Make sure that the unit is turned off before adjusting

the DIP switches. If you adjust the switches while the

unit is turned on, the new switch positions are not

applied.

The following information explains how the DIP

switch positions.

• Switches 1 and 2 (unit ID)

These DIP switches, along with the [UNIT ID],

determine the unit's UNIT ID when Quick Config is not

used.

The UNIT ID is determined as follows.

When Quick Config is used, these switches are

disabled.

• Switch 3 (initialize mode)

This DIP switch is used to reset the unit to its factory

default settings.

After the unit is reset, it starts up using the system

mode that corresponds to the position of switches 7

and 8.

ձղճ յնշմ

CAUTION

Make sure the unit is turned off before connecting or

disconnecting the power cord.

CAUTION

Do not block the ventilation ports (heat dissipating slits) on this

product. This product has ventilation ports at the front/rear/sides

to prevent the internal temperature from becoming too high. If

the ventilation ports are blocked, heat will get trapped inside the

product, which may cause malfunction or fire.

Switch

position

[UNIT ID]

= 1

[UNIT ID]

= 2

[UNIT ID]

= 3

01 02 03

04 05 06

07 0809

0A 0B 0C

Switch

position Initialize mode

Initialize mode is off (unit will not be reset

when it is turned on)

Initialize mode is on (unit will be reset

when it is turned on)

1 2

Device features

Owner’s Manual

Tio1608-D2

• Switches 3, 7 and 8 (Tio1608-D compatibility

mode)

This mode is used to connect to older models that are

not compatible with the Tio1608-D2.

In the compatibility mode, the sampling frequency is

set to the maximum 48 kHz and external devices

recognize Tio1608-D2 as Tio1608-D.

- Activating the Tio1608-D compatibility mode

Configure the dip switches as shown above for

"Tio1608-D compatibility mode" and then switch the

power ON. When the red indicators on the front panel

stop flashing and only the green indicators are

flashing, that indicates the compatibility mode has

been successfully activated. Then switch the power

OFF, reconfigure the dip switch settings appropriately,

and switch the power back ON before using the

system. The green [SYSTEM] indicators will flash for

about 20 seconds only after switching to the Tio1608-

D compatibility mode.

- Canceling the Tio1608-D compatibility mode

Configure the dip switches as shown above for

"Cancels the Tio1608-D compatibility mode" and then

switch the power ON. When the red indicators on the

front panel stop flashing and only the green indicators

are flashing, that indicates the compatibility mode has

been successfully canceled. Then switch the power

OFF, reconfigure the dip switch settings appropriately,

and switch the power back ON before using the

system.

• Switch 4 (Dante SECONDARY port mode)

This switch determines the operating mode of the

Dante [SECONDARY].

When Quick Config is used, these switches are

disabled.

• Switches 5 and 6 (IP address mode)

These switches determine how the unit's IP address is

set.

• Switches 7 and 8 (start up mode)

These switches determine how the unit starts up

during start up mode. When set to "refresh" mode, the

settings of the mixer are applied when the unit starts

up. When set to "resume" mode, the unit returns to

the same state as the last time it was used.

When Quick Config is used, the "normal operation"

mode settings are disabled.

NOTE

If switches 7 and 8 are set to the "update mode" or

"diagnostic mode" positions, the unit will not be reset.

Switch

position Operating mode

Tio1608-D compatibility mode

Cancels the Tio1608-D compatibility mode

(initialize mode)

Switch

position [SECONDARY] operating mode

Daisy chain connection

Redundant connection

NOTE

When the Switch 4 is set to "Redundant connection", the

head amp control function (page 15) is only available via

the Dante [PRIMARY].

378

Switch

position IP address mode

Auto IP (link local)

DHCP

Static IP Auto (192.168.0.ID)

Static IP Manual

The IP address is specified from an

external device such as R Remote V3.

Switch

position Start up mode

REFRESH mode (normal operation)

RESUME mode (normal operation)

Update mode

Diagnostic mode

NOTE

• Update mode and diagnostic mode are used when

performing maintenance on the unit. Normally you will not

use these modes.

• Update mode and diagnostic mode can be enabled even

when using Quick Config. Normally you will not use these

modes.

5 6

7 8

Device features

Owner’s Manual

Tio1608-D2

English

Dante [PRIMARY]/[SECONDARY]

etherCON CAT5 connector that connects the unit to a

Dante device, such as a NY64-D digital audio interface

card. When DIP switch 4 is set to the daisy-chain

connection position (i.e., up position), signals

received on one connector are sent out via the other

connector. When DIP switch 4 is set to the redundant

connection position (i.e., down position), the

[SECONDARY] functions as a backup and carries the

same signals as the [PRIMARY]. If for some reason

signals cannot be carried over the [PRIMARY] (for

example, because the cable becomes damaged or

disconnected, or because the network switch

malfunctions), the unit switches to the [SECONDARY].

[LINK/ACT]

Indicate the status of the signals carried by the

[PRIMARY] and [SECONDARY]. If an indicator is

flashing quickly, the corresponding Ethernet cable is

not connected properly.

[1G]

Indicate the connection status of the [PRIMARY] and

[SECONDARY]. If an indicator is lit, the corresponding

connector is connected to a Gigabit Ethernet network.

NOTICE

Use an STP (Shielded Twisted Pair) cable to prevent

electromagnetic interference. Make sure that the metal parts of

the plugs are electrically connected to the STP cable shield by

conductive tape or comparable means.

NOTE

• We recommend using RJ-45 plugs that are compatible with

Neutrik etherCON CAT5 connectors. You can also use

cables with standard RJ-45 plugs.

•The maximum length of cable that can be used varies

depending on the type of cable. When using CAT5e cables,

data can be sent between devices that are connected by up

to 100 m of cable.

Connection methods

Owner’s Manual

Tio1608-D2

Connection methods

This section explains the different methods for connecting

the Tio1608-D2 to other Dante devices. To connect to a

non-TF series mixer, refer to the mixer instruction manual.

Quick Config (automatic setup)

When connecting the unit to a TF series mixing console,

Quick Config makes it easy to set up the unit automatically.

It allows you to connect up to three Tio1608-D2 units to one

TF series mixing console, and configures Dante network

settings and audio signal settings in one operation.

Tio1608-D2 procedure

1. With all the units turned off, set the DIP switches on

the rear panel to the up position.

2. Set the [QUICK CONFIG FOR TF] on the front panel

to the [ON] position.

3. Set the [UNIT ID] on the front panel to the desired

position.

If you are using multiple Tio1608-D2 units, make

sure each unit has a unique UNIT ID setting.

4. Use Ethernet cables to connect the Tio1608-D2 to

the NY64-D card (installed in the TF series mixing

console) or to other Tio1608-D2 units in a daisy-

chain configuration, as shown below.

When using Quick Config, the units will operate the same

whether you connect the Ethernet cables to the Dante

[PRIMARY] or [SECONDARY].

When connecting 3 units

5. Turn each device on.

TF series mixing console procedure

6. Display the console's SYSTEM SETUP  SLOT SETUP

screen, and confirm that Quick Config is enabled.

Now the TF series mixing console can recognize the

Tio1608-D2 units, and all Dante settings and input and output

patching settings will be configured automatically.

When the Quick Config button is displayed in white, Quick

Config is enabled. If the button is grayed out, click it. If you

cannot enable Quick Config, return to step 1 and confirm that

the Tio1608-D2 is configured properly.

NOTE

•To use Quick Config functionality, activate the Tio1608-D

compatibility mode.

•Tio1608-D2 models can be connected to a mixture of Tio1608-

D2 and older Tio1608-D models.

•An NY64-D audio interface card (sold separately) is required to

connect a Tio1608-D2 to a TF series mixing console.

NOTE

If used in combination with older Tio1608-D models, specify UNIT

ID settings that do not conflict with the Tio1608-D units.

TF Series (NY64-D)

Tio1608-D2 UNIT ID=1

Tio1608-D2 UNIT ID=2

Tio1608-D2 UNIT ID=3

[PRIMARY] or

[SECONDARY]

[PRIMARY]

[SECONDARY]

[PRIMARY] or

[SECONDARY]

Connection methods

Owner’s Manual

Tio1608-D2

English

7. To assign the Tio1608-D2 inputs to the TF series

mixing console, set the input select on the console's

INPUT screen to "SLOT".

8. Adjust the input gain and other settings as

necessary.

Quick config is now complete.

Settings configured by Quick Config

Quick Config applies the following settings.

•Dante settings

•Patching

Manual setup

If Quick Config is not used or if connecting to a mixer that

does not support Quick Config, configure settings manually

based on the given connection environment.

Tio1608-D2 procedure

With the unit turned off, set the [QUICK CONFIG FOR

TF] on the front panel to the [OFF] position.

Refer to the information on page 11 - 12 and set the

DIP switches to the desired positions.

Set the [UNIT ID] on the front panel to the desired

position.

Use Ethernet cables to connect the Tio1608-D2 to

your Dante device.

Turn each device on.

Dante settings

When using manual setup, use Dante Controller to

configure Dante settings.

Dante Controller is a computer program that you can use to

configure Dante network settings and audio signal patching

settings. To use the program, download it from the Audinate

website. (Dante Controller v3.2.1 or later is compatible with

Tio1608-D2.)

For information about Dante Controller, refer to the Dante

Controller documentation.

When using manual setup, you will need to use Dante

Controller to configure the following settings at a minimum.

(You can configure other settings as desired.)

•Input and output patching settings (Network View 

Routing)

• Clock leader settings (Network View  Clock Status)

• Sampling frequency settings (Device View  Config)

Head amp control

You can use a Yamaha digital mixer or other device to

control the Tio1608-D2 head amp.

When the unit is connected to a TF series mixing console,

you can control the unit's head amp just as you would adjust

the console's head amp.

When using a CL or QL series digital mixer, you can control

or use the following parameters.

•HA gain

•+48 V phantom power on/off

• HPF on/off

•HPF frequency cutoff adjustment

•Mute off

•+48 V phantom power on/off display

• Analog input level meter display

•Firmware version display

• Device identify

• Dante SYSTEM and SYNC indicator information

NOTE

While the INPUT screen is displayed, the menu keys can be

used to change multiple currently selected FADER BANK

inputs at the same time.

Word clock 48 kHz (follower), no pull up/down

Latency 0.5 ms

Encoding 24-bit PCM

SECONDARY port mode Daisy chain

Patching Refer to the table below

IP address Previous setting is used

NOTE

Quick Config does not configure analog input parameters.

Tio input TF input TF output Tio output

#1 ID 1, Input 1 Channel 1 AUX 1 ID 1, Output 1

ID 1, Input 2 Channel 2 : :

::AUX 6ID 1, Output 6

ID 1, Input 16 Channel 16 Stereo L ID 1, Output 7

Stereo R ID 1, Output 8

#2 ID 2, Input 1 Channel 17 AUX 7 ID 2, Output 1

ID 2, Input 2 Channel 18 : :

AUX 12 ID 2, Output 6

ID 2, Input 16 Channel 32 Stereo L ID 2, Output 7

Stereo R ID 2, Output 8

#3 ID 3, Input 1 Channel 33 AUX 13 ID 3, Output 1

ID 3, Input 2 Channel 34 : :

::AUX 18ID 3, Output 6

ID 3, Input 8 Channel 40 AUX 19 ID 3, Output 7

AUX 20 ID 3, Output 8

NOTE

• Even if only UNIT ID 2 or 3 is used, channels are patched as

shown above based on the UNIT ID number.

•After you have used Quick Config to configure the settings, you

can use Dante Controller to change the individual settings.

However, each time the Tio1608-D2 is turned on, Dante

Controller settings will be replaced by the Quick Config settings.

For this reason, we recommend that you turn Quick Config off if

you are using Dante Controller.

NOTE

When the Dante SECONDARY port mode (page 12) is set to

"Redundant connection", the head amp control function is only

available via the Dante [PRIMARY]. The Dante [SECONDARY] is

not available for this function.

Troubleshooting

Owner’s Manual

Tio1608-D2

Troubleshooting

Issue Cause Solution

No power, power indicator does

not light

Power cord not connected. Make sure the power cord is connected (page

11).

The power switch is turned off.

Set the power switch to the "on" position. If you

still cannot resolve the problem, please contact

your nearest Yamaha representative.

Unit is not receiving an input

signal

Cables not connected properly. Make sure all cables are connected properly.

Source device is not sending a

signal to the unit.

Output a signal from the source device and

confirm that the [STATUS INPUT] light.

Internal head amp gain is too low. Adjust the internal head amp gain to an

appropriate level.

DIP switches are set to "refresh"

mode but device that controls the

Tio1608-D2 has not started up.

Start the device that will control the Tio1608-D2

and send the settings to the Tio1608-D2.

Input level too low

Condenser mic is connected.

Set the [+48V ACTIVE] to the "on" position.

Use the device that controls the Tio1608-D2 to

turn on phantom power for the corresponding

channel.

Internal head amp gain is too low. Adjust the internal head amp gain to an

appropriate level.

No sound heard

Cables not connected properly. Make sure all cables are connected properly.

DIP switches are set to "refresh"

mode but device that controls the

Tio1608-D2 has not started up.

Start the device that will control the Tio1608-D2

and send the settings to the Tio1608-D2.

The [QUICK CONFIG FOR TF] is ON

in an environment where Quick

Config cannot be used (when

connected to mixer that does not

support Quick Config or when

settings were configured in Dante

Controller).

Set the [QUICK CONFIG FOR TF] to OFF and

then try configuring the patch or other settings

again.

The sampling frequency does not

match the connected mixer.

Set the settings correctly in Dante Controller or

other software.

An error has occurred.

Check the status of [SYSTEM] and [SYNC] and

then resolve the problem accordingly. (page

17-18)

[UNIT ID] or DIP switch settings

not applied

You changed the switch positions

while the unit was turned on.

Make sure the unit is turned off before

changing the switch positions.

How to read the indicators

Owner’s Manual

Tio1608-D2

English

How to read the indicators

You can use the [SYSTEM] and [SYNC] to confirm the unit's status.

The indicators can relay operational status, error status, and warnings.

Error status

If one of the following errors has occurred, the device will not operate. Until the error is resolved, the green [SYSTEM] will be

turned off, and all indicators for all I/O channels will continue to flash.

In addition, certain errors will cause the red [SYSTEM] to light or flash.

The following errors affect the settings or the hardware. However, the device will still be usable. The green [SYSTEM] will light,

and all indicators for all I/O channels will work normally.

In addition, certain errors will cause the red [SYSTEM] to light or flash.

[SYSTEM] Description Possible Solution

Off Flashes 2 times

Internal Dante error has occurred. The unit is malfunctioning. Please contact

your nearest Yamaha representative.

Off Flashes 3 times

MAC address setting is damaged and Dante

communication is not possible.

Off Lit

Duplicate UNIT ID was found. Make sure each UNIT ID is only used once

on the Dante network.

[SYSTEM] Description Possible Solution

Lit Flashing

The number of Dante transmit flows

exceeded the limit.

Reduce the number of flows by, for example,

using Dante Controller to change some of the

transmit flows to multicast.

Lit Flashes 2 times

Error occurred when communicating with the

head amp.

Turn the unit off and then on again. If this does

not resolve the problem, please contact your

nearest Yamaha representative.

Lit Flashes 3 times

Internal memory has been corrupted. If using RESUME mode, turn the unit off and

then on again. If this does not resolve the

problem, please contact your nearest

Yamaha epresentative.

Lit Lit

You changed the positions of the device

setting DIP switches, or changed the Dante

settings from Dante Controller. Therefore, the

positions of the device setting DIP switches

do not match the actual Dante settings.

If the Device Lock setting was enabled from

Dante Controller, disable the setting, or

check the device setting DIP switch

positions, and set them to accommodate the

current situation.

How to read the indicators

Owner’s Manual

Tio1608-D2

Warnings

The indicators will light and/or flash as shown until the cause is resolved.

If the green [SYNC] is unlit, the unit’s clock is unconfirmed.

If the green indicator is flashing, the unit is the clock leader.

If the green indicator is lit, the unit is the clock follower and the clock is synchronized.

Information Message

The indicators will remain lit and/or flashing cyclically to report the status.

If the orange [SYNC] is unlit, the unit is operating normally.

If the green [SYNC] is unlit, the unit's clock is unconfirmed.

[SYNC] Description Possible Solution

Off Flashing

Clock settings are incorrect. Check the clock leader and sampling

frequency settings of the Tio1608-D2 and

Dante Controller.

Off Flashes 2 times

Unit not connected to Dante network. Make sure the cables are not damaged and

that they are connected properly.

Off Flashes 3 times

Cable wiring is wrong; cannot find other

Dante devices.

Check the wiring of the Ethernet cables.

[SYNC] Description Possible Solution

Lit or flashing Lit

Device that is not Gigabit Ethernet

compatible is connected.

To use Dante to send and receive digital

audio, make sure your devices are Gigabit

Ethernet compatible.

Lit or flashing Flashing

When using a redundancy network,

[SECONDARY] is sending/receiving audio.

Check the connections of the network

connected to the [PRIMARY].

Lit or flashing Flashes 2 times

When using a redundancy network, error

was detected on the [SECONDARY].

Check the connections of the network

connected to the [SECONDARY].

[SYNC] Description Possible Solution

Off Lit

Synchronizing on a Dante network. Please wait until started has completed or

until the unit has finished synchronization. It

may take up to 45 seconds for completion.

Waiting to receive setting data. If START UP MODE is set to REFRESH on

the Tio1608-D2 unit, the input/output will be

muted until the unit receives setting data after

it starts up.

Flashing Off

The unit is functioning correctly as the word

clock leader.

The unit is operating as the word clock

leader.

Lit Off

The unit is functioning correctly as the word

clock follower.

The unit is operating as the clock follower

and the clock is synchronized.

Specifications

Owner’s Manual

Tio1608-D2

121

EnglishDeutschFrançais

EspañolPortuguêsItaliano

Русский

Specifications

General Specifications

Output impedance of signal generator: 150 ohms

Measured with another Tio1608-D2 through Dante network.

Frequency Response

Fs = 20Hz-20kHz, refer to the nominal output level @1kHz

Total Harmonic Distortion

Fs = 44.1kHz or 48kHz

Fs = 88.2kHz or 96kHz

* Total Harmonic Distortion is measured with a -18dB/octave filter @80kHz

Hum & Noise

Fs = 48kHz, EIN: Equivalent Input Noise

Fs = 96kHz, EIN: Equivalent Input Noise

* Hum & Noise are measured with A-weighting filter.

Dynamic Range

Fs = 48kHz

Fs = 96kHz

* Dynamic Range are measured with A-weighting filter.

Crosstalk@1kHz

* Crosstalk is measured with a -30dB/octave filter @22kHz

Sampling Frequency

Power Requirements

Input Output RL Conditions Min. Typ. Max. Unit

INPUT1-16 OUTPUT 1-8 600Ω GAIN: +66dB. -1.5 0.0 0.5 dB

Input Output RL Conditions Min. Typ. Max. Unit

INPUT1-16 OUTPUT 1-8 600Ω +4dBu@20Hz-20kHz, GAIN: +66dB. 0.1 %

600Ω +4dBu@20Hz-20kHz, GAIN: -6dB. 0.05 %

Input Output RL Conditions Min. Typ. Max. Unit

INPUT1-16 OUTPUT 1-8 600Ω +4dBu@20Hz-20kHz, GAIN: +66dB. 0.2 %

600Ω +4dBu@20Hz-20kHz, GAIN: -6dB. 0.05 %

Input Output RL Conditions Min. Typ. Max. Unit

INPUT1-16 OUTPUT 1-8 600Ω Rs=150Ω, GAIN: +66dB. -128

EIN dBu

-62 dBu

600Ω Rs=150Ω, GAIN: -6dB. -84 -80 dBu

all Inputs OUTPUT 1-8 600Ω Rs=150Ω, GAINs: -6dB. -70 dBu

- OUTPUT 1-8 600Ω Residual output noise -88 dBu

Input Output RL Conditions Min. Typ. Max. Unit

INPUT1-16 OUTPUT 1-8 600Ω Rs=150Ω, GAIN: +66dB. -128

EIN dBu

-62 dBu

600Ω Rs=150Ω, GAIN: -6dB. -84 -80 dBu

all Inputs OUTPUT 1-8 600Ω Rs=150Ω, GAINs: -6dB. -70 dBu

- OUTPUT 1-8 600Ω Residual output noise -86 dBu

Input Output RL Conditions Min. Typ. Max. Unit

INPUT1-16 OUTPUT 1-8 600Ω AD + DA, GAIN: -6dB. 108 dB

- OUTPUT 1-8 600Ω DA Converter 112 dB

Input Output RL Conditions Min. Typ. Max. Unit

INPUT1-16 OUTPUT 1-8 600Ω AD + DA, GAIN: -6dB. 108 dB

- OUTPUT 1-8 600Ω DA Converter 110 dB

from/to to/from Conditions Min. Typ. Max. Unit

INPUT n INPUT (n-1) or (n+1) INPUT1-16

adjacent inputs, GAIN: -6dB. -100 dB

OUTPUT n OUTPUT (n-1) or (n+1) OUTPUT 1-8, input to output -100 dB

Conditions Min. Typ. Max. Unit

External Clock Frequency Range 44.1kHz / 48kHz / 88.2kHz / 96kHz -200 +200 ppm

+4.1667%/+0.1%/-0.1%/-4.0% to all of the above -200 +200 ppm

Conditions Min. Typ. Max. Unit

Power Requirements 100-240V 50/60Hz 50 W

Heat Dissipation 100-240V 50/60Hz 43.5 kcal/h

Specifications

Owner’s Manual

Tio1608-D2

122

AC Cable Length and Temperature Range

Dimensions (W x H x D) & Net weight

480(W) x 88(H) x 364(D) mm, 5.7kg

Input Output Digital I/O Character

Analog input characteristics

Analog output characteristics

Digital input/output specifications

* The contents of this manual apply to the latest specifications as of the publishing date. To obtain the latest manual, access

the Yamaha website then download the manual file.

* Der Inhalt dieser Bedienungsanleitung gilt für die neuesten technischen Daten zum Zeitpunkt der Veröffentlichung. Um die

neueste Version der Anleitung zu erhalten, rufen Sie die Website von Yamaha auf und laden Sie dann die Datei mit der

Bedienungsanleitung herunter.

* Le contenu de ce mode d’emploi s’applique aux dernières caractéristiques techniques connues à la date de publication du

manuel. Pour obtenir la version la plus récente du manuel, accédez au site Web de Yamaha puis téléchargez le fichier du

manuel concerné.

* El contenido de este manual se aplica a las últimas especificaciones según la fecha de publicación. Para obtener el último

manual, acceda al sitio web de Yamaha y descargue el archivo del manual.

* O conteúdo deste manual se aplica às especificações mais recentes a partir da data de publicação. Para obter o manual

mais recente, acesse o site da Yamaha e faça o download do arquivo do manual.

*Il contenuto del presente manuale si applica alle ultime specifiche tecniche a partire dalla data di pubblicazione. Per ottenere

la versione più recente del manuale, accedere al sito Web Yamaha e scaricare il file corrispondente.

* В содержании данного руководства приведены последние на момент публикации технические характеристики.

Для получения последней версии руководства посетите веб-сайт корпорации Yamaha и загрузите файл с

руководством.

Conditions Min. Typ. Max. Unit

AC Cable Length 2.5 m

Temperature Range Operating temperature range 0 40 °C

Storage temperature range -20 60 °C

Input Termi-

nals GAIN Actual Load

Impedance For Use With

Nominal

Input Level Connector balanced /

Unbalanced

Sensitivity

*1. Sensitivity is the lowest level that will produce an output of +4dBu (1.23V) or the nominal output level when the unit is set to maximum gain.

Nominal Max. before clip

INPUT1-16 +66dB 7.5kΩ 50-600Ω Mics

or 600Ω Lines -82dBu

(61.6μV) -62dBu

(0.616mV) -42dBu

(6.16mV) Combo

(XLR 3-hole

chassis

or TRS

phone

)

*2. 1: GND, 2: HOT, 3: COLD

*3. Tip: HOT, Ring: COLD, Sleeve: GND

Balanced

-6dB -10dBu

(245mV) +10dBu

(2.45V) +30dBu

(24.5V)

In these specifications, 0dBu = 0.775Vrms.

+48V DC (phantom power) can be supplied to INPUT XLR type connectors via each individual software controlled switch.

Output Terminals Actual Sourcez

Impedance For Use With

Nominal

Output Level Connector balanced /

Unbalanced

Nominal Max. before clip

OUTPUT 1-8 75Ω 600Ω Lines +4dBu

(1.23 V) +24dBu

(12.3 V) XLR 3-pin

chassis

*1. 1: GND, 2: HOT, 3: COLD

Balanced

In these specifications, 0dBu = 0.775Vrms.

Terminal Format Data length Level Audio Connector

Primary / Secondary Dante 24 or 32bit 1000BASE-T 16ch (Tio1608-D2 to other devices)

8ch (Other devices to Tio1608-D2) etherCON Cat5e

La page charge ...

Yamaha Tio1608 Le manuel du propriétaire

Marque: Yamaha

Modèle: Tio1608

Catégorie: Matériel musical

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

italiano: Yamaha Tio1608 Manuale del proprietario
English: Yamaha Tio1608 Owner's manual
español: Yamaha Tio1608 El manual del propietario
Deutsch: Yamaha Tio1608 Bedienungsanleitung
русский: Yamaha Tio1608 Инструкция по применению
Nederlands: Yamaha Tio1608 de handleiding
português: Yamaha Tio1608 Manual do proprietário
dansk: Yamaha Tio1608 Brugervejledning
polski: Yamaha Tio1608 Instrukcja obsługi
čeština: Yamaha Tio1608 Návod k obsluze
svenska: Yamaha Tio1608 Bruksanvisning
日本語: Yamaha Tio1608 取扱説明書
suomi: Yamaha Tio1608 Omistajan opas
română: Yamaha Tio1608 Manualul proprietarului