DeWalt D55171 Manuel utilisateur

D55171

Oil Free Portable Air Compressor

Compresseur d’air portatif sans huile

Compresor de aire sin aceite portátil

INSTRUCTION MANUAL

GUIDE D'UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES

DE USAR EL PRODUCTO.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-De

2



A. Sliding Handles

B. Drain Valve

C. Storage Support

D. Regulated Pressure Gauge

E. Quick Connects

F. Regulator

G. Safety Valve



Voltage: Single 120V

Minimum branch circuit requirement: 15 A

Fuse Type: Time delay



MODEL

D55171

WEIGHT

126 lbs. (57.2 kg)

HEIGHT

18.0" (457.2 mm)

WIDTH

24.0" (609.6 mm)

LENGTH

33.0" (838.2 mm)

AIR TANK CAPACITY (GALLONS)

7.5 Gallon (28.4 liters)

APPROX CUT-IN PRESSURE

145 PSI

APPROX. CUT-OUT PRESSURE

175 PSI

SCFM @ 100 PSI

*4.6

NOISE LEVEL

+74 dBA

*Tested per ISO 1217

+Tested per ISO 3744



H. Pressure Switch

I. Cord Wrap

J. Air Filter

K. Tank Pressure Gauge

L. On/Auto/Off Switch





Noise Emission Values

Sound Pressure Level: LpA = 74.0 dBA re 20μPA

Uncertainty in the Sound Pressure Level: KpA = 3.0 dBA re 20μPA

Sound Power Level: LwA = 87.0 dBA re 1 pw

Uncertainty in the Sound Power Level: KwA = 3.0 dBA re 1 pw

The sum of the emission value and the uncertainty is the limit

below which there is a 95% confidence the value of a single tool

will lie below when the tool is new.

FIG. 1

E

A

F

L

H

I

D

K

C

B

G

J

3





The definitions below describe the level of severity

for each signal word. Please read the manual and pay

attention to these symbols.

DANGER: Indicates an imminently hazardous situa-

tion which, if not avoided, will result in death or seri-

ous injury.

WARNING: Indicates a potentially hazardous

situation which, if not avoided, could result in death or

serious injury.

CAUTION: Indicates a potentially hazardous

situation which, if not avoided, may result in minor or

moderate injury.

CAUTION: Used without the safety alert symbol

indicates a potentially hazardous situation which, if not

avoided, may result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT

THIS OR ANY D

e

WALT TOOL, CALL US TOLL FREE AT:

1-800-4-D

e

WALT (1-800-433-9258)



WARNING: Do not operate this unit until you read and understand

this instruction manual for safety, operation and maintenance

instructions.

WARNING: This product contains chemicals known to the

State of California to cause cancer, and birth defects or other

reproductive harm. Wash hands after handling.

WARNING: Some dust contains chemicals known to the State of

California to cause cancer, birth defects or other reproductive harm

such as asbestos and lead in lead based paint.



DANGER: RISK OF EXPLOSION OR FIRE

WHAT CAN HAPPEN HOW TO PREVENT IT

 • Itisnormalforelectrical

contacts within the motor

and pressure switch to

spark.

 • Alwaysoperatethecompres-

sor in a well ventilated area

free of combustible materials,

gasoline, or solvent vapors.

 • Ifelectricalsparksfrom

compressor come into con-

tact with flammable vapors,

they may ignite, causing fire

or explosion.

 • Ifsprayingflammablemate-

rials, locate compressor

at least 20' (6.1 m) away

from spray area. An addi-

tional length of hose may be

required.

 • Storeflammablematerialsin

a secure location away from

compressor.

4



 • Restrictinganyofthecom-

pressor ventilation openings

will cause serious overheat-

ing and could cause fire.

 • Neverplaceobjectsagainst

or on top of compressor

pump.

 • Operatecompressorin

an open area at least 12"

(30.5 cm) away from any

wall or obstruction that would

restrict the flow of fresh air to

the ventilation openings.

 • Operatecompressorina

clean, dry well ventilated area.

Do not operate unit indoors or

in any confined area.

 • Unattendedoperationof

this product could result in

personalinjuryorproperty

damage. To reduce the

risk of fire, do not allow

the compressor to operate

unattended.

 • Alwaysremaininattendance

with the product when it is

operating.

 • Always turn off and unplug

unit when not in use.

DANGER: RISK TO BREATHING (ASPHYXIATION)

WHAT CAN HAPPEN HOW TO PREVENT IT

• Thecompressedairdirectly

from your compressor is not

safe for breathing. The air

stream may contain carbon

monoxide, toxic vapors,

or solid particles from the

air tank. Breathing these

contaminants can cause

seriousinjuryordeath.

• Airobtaineddirectlyfromthe

compressor should never

be used to supply air for

human consumption. In order

to use air produced by this

compressor for breathing,

suitable filters and in-line

safety equipment must be

properly installed. In-line

filters and safety equipment

usedinconjunctionwiththe

compressor must be capable

of treating air to all applicable

local and federal codes prior to

human consumption.

• Sprayedmaterialssuchas

paint, paint solvents, paint

remover, insecticides, weed

killers, may contain harmful

vapors and poisons.

• Workinanareawithgood

cross ventilation. Read and

follow the safety instructions

provided on the label or safety

data sheets for the materials

you are spraying. Always use

certified safety equipment:

OSHA/MSHA/NIOSH

respiratory protection designed

for use with your specific

application.

5



• Somedustcreatedby

power tools may contain

harmful chemicals.

• Toreduceyourexposure

to these chemicals: work in

a well ventilated area and

al ways wear OSHA/MSHA/

NIOSH approved, properly

fit ting face mask or res pi ra tor

when us ing such tools.

WARNING: RISK OF BURSTING

Air Tank: The air tank on your Air Compressor is designed and

may be UM coded [for units with air tanks greater than 6" (152 mm)

diameter] according to ASME Section VIII, Div. 1 rules. All pressure

vessels should be inspected once every two years. To find your state

pressure vessels inspector, look under the Division of Labor and

Industries in the government section of a phone book or call 1-800-

4-D

eWALT for assistance.

The following conditions could lead to a weakening of the air tank,

and result in a violent air tank explosion:

WHAT CAN HAPPEN HOW TO PREVENT IT

• Failuretoproperlydrain

condensed water from

air tank, causing rust and

thinning of the steel air tank.

• Drainairtankdailyorafter

each use. If air tank develops

a leak, replace it immediately

with a new air tank or replace

the entire compressor.

• Modificationsorattempted

repairs to the air tank.

• Neverdrillinto,weld,ormake

any modifications to the air

tank or its attachments. Never

attempt to repair a damaged or

leaking air tank. Replace with a

new air tank.

• Unauthorizedmodifications

to the safety valve or any

other components which

control air tank pressure.

• Theairtankisdesigned

to withstand specific

operating pressures. Never

makeadjustmentsorparts

substitutions to alter the factory

set operating pressures.

Attachments & accessories:

• Exceedingthepressure

rating of air tools, spray guns,

air operated accessories,

tires, and other inflatables

can cause them to explode

or fly apart, and could result

inseriousinjury.

• Followtheequipmentmanu-

facturers recommendation

and never exceed the maxi-

mum allowable pressure rat-

ing of attachments. Never

use compressor to inflate

smalllowpressureobjects

such as children’s toys, foot-

balls, basketballs, etc.

6



Tires:

• Over inflation of tires could

resultinseriousinjuryand

property damage.

 • Useatirepressuregaugeto

check the tires pressure before

each use and while inflating

tires; see the tire sidewall for

the correct tire pressure.

NOTE: Air tanks, compressors and

similar equipment used to inflate

tires can fill small tires similar to

theseveryrapidly.Adjustpressure

regulator on air supply to no more

than the rating of the tire pressure.

Add air in small increments and

frequently use the tire gauge to

prevent over inflation.

WARNING: RISK OF ELECTRICAL SHOCK

WHAT CAN HAPPEN HOW TO PREVENT IT

• Your air compressor is

powered by electricity.

Like any other electrically

powered device, If it is not

used properly it may cause

electric shock.

 • Never operate the

compressor outdoors when it

is raining or in wet conditions.

 • Never operate compressor

with protective covers

removed or damaged.

 • Repairs attempted by

unqualified personnel can

resultinseriousinjuryor

death by electrocution.

 • Any electrical wiring or

repairs required on this

product should be performed

by a D

eWALT factory

service center or a D

eWALT

authorizedservicecenterin

accordance with national and

local electrical codes.

 • Electrical Grounding:

Failure to provide adequate

grounding to this product

couldresultinseriousinjury

or death from electrocution.

See Grounding

Instructions under

Installation.

 • Make certain that the

electrical circuit to which the

compressor is connected

provides proper electrical

grounding, correct voltage

and adequate fuse protection.

WARNING: RISK FROM FLYING OBJECTS

WHAT CAN HAPPEN HOW TO PREVENT IT

• Thecompressedairstream

can cause soft tissue

damage to exposed skin and

can propel dirt, chips, loose

particles,andsmallobjects

at high speed, resulting in

property damage or personal

injury.

• Always wear certified safety

equipment: ANSI Z87.1 eye

protection (CAN/CSA Z94.3)

with side shields when using

the compressor.

• Neverpointanynozzleor

sprayer toward any part of

the body or at other people or

animals.

7



• Alwaysturnthecompressoroff

and bleed pressure from the

air hose and air tank before

attempting maintenance,

attaching tools or accessories.

WARNING: RISK OF HOT SURFACES

WHAT CAN HAPPEN HOW TO PREVENT IT

• Touchingexposedmetal

such as the compressor

head, engine head, engine

exhaust or outlet tubes, can

result in serious burns.

 • Nevertouchanyexposed

metal parts on compressor

during or immediately after

operation. Compressor will

remain hot for several minutes

after operation.

 • Donotreacharound

protective shrouds or attempt

maintenance until unit has

been allowed to cool.

WARNING: RISK FROM MOVING PARTS

WHAT CAN HAPPEN HOW TO PREVENT IT

• Movingpartssuchasthe

pulley, flywheel, and belt can

causeseriousinjuryifthey

come into contact with you or

your clothing.

• Neveroperatethecompressor

with guards or covers which

are damaged or removed.

• Keepyourhair,clothing,and

gloves away from moving

parts.Looseclothes,jewelry,

or long hair can be caught in

moving parts.

• Airventsmaycovermoving

parts and should be avoided

as well.

• Attemptingtooperate

compressor with damaged or

missing parts or attempting

to repair compressor with

protective shrouds removed

can expose you to moving

parts and can result in

seriousinjury.

• Anyrepairsrequiredonthis

product should be performed

by a D

eWALT factory

service center or a D

eWALT

authorizedservicecenter.

8



WARNING: RISK OF FALLING

WHAT CAN HAPPEN HOW TO PREVENT IT

• Aportablecompressor

can fall from a table,

workbench, or roof causing

damage to the compressor

and could result in serious

injuryordeathtothe

operator.

• Alwaysoperatecompressor

in a stable secure position to

prevent accidental movement

of the unit. Never operate

compressor on a roof or

other elevated position. Use

additional air hose to reach

high locations.

WARNING: RISK OF

INJURY FROM LIFTING

WHAT CAN HAPPEN HOW TO PREVENT IT

 • Seriousinjurycanresult

from attempting to lift too

heavyanobject.

•The compressor is too heavy

to be lifted by one person.

Obtain assistance from

others before lifting.

CAUTION: RISK FROM NOISE

WHAT CAN HAPPEN HOW TO PREVENT IT

 • Under some conditionsand

duration of use, noise from

this product may contribute

to hearing loss.

 • Alwayswearcertifiedsafety

equipment: ANSI S12.6

(S3.19) hearing protection.

WARNING: RISK OF UNSAFE OPERATION

WHAT CAN HAPPEN HOW TO PREVENT IT

• Unsafeoperationofyourair

compressor could lead to se ri-

ousinjuryordeathtoyouor

others.

• Reviewandunderstandall

instructions and warnings in

this manual.

• Becomefamiliarwiththe

op eration and con trols of the

air compressor.

• Keepoperatingareaclear

of all persons, pets, and

obstacles.

• Keepchildrenawayfromthe

air compressor at all times.

• Donotoperatetheproduct

when fatigued or under the

influence of alcohol or drugs.

Stay alert at all times.

• Neverdefeatthesafetyfea

tures of this prod uct.

• Equipareaofoperationwith

a fire extinguisher.

• Donotoperatemachinewith

missing, broken, or un au tho-

rizedparts.

• Neverstandonthe

compressor.

9







)

ON/AUTO/OFF SWITCH

Place this switch (L) in the ON/AUTO

H

L

position to provide automatic power to the

pressure switch and OFF to remove power

at the end of each use. NOTE: ALWAYS

ensure the switch (L) is in the OFF

position before removing or replacing

pressure switch cover.

PRESSURE SWITCH

The pressure switch (H) automatically starts the motor when the

air tank pressure drops below the factory set cut-in pressure. It

stops the motor when the air tank pressure reaches the factory set

cut-out pressure.

SAFETY VALVE

If the pressure switch does not shut off the air

G

compressor at its cut-out pressure setting, the

safety valve (G) will protect against high pressure

by popping out at its factory set pressure (slightly

higher than the pressure switch cut-out setting).

CHECK VALVE

When the air compressor is operating, the check valve is open,

allowing compressed air to enter the air tank. When the air

compressor reaches cut-out pressure, the check valve closes,

allowing air pressure to remain inside the air tank.

TANK PRESSURE GAUGE

The tank pressure gauge (K) indi-

E

F

D

K

cates the reserve air pressure in

the tank.

REGULATED PRESSURE

GAUGE

The regulated pressure gauge (D)

indicates the air pressure available

at the outlet side of the regulator. This pressure is controlled by the

regulator and is always less than or equal to the tank pressure.

REGULATOR

The regulator (F) controls the air pressure shown on the regulated

pressure gauge. Pull the knob out and turn clockwise to increase

pressure and counterclockwise to decrease pressure. When the

desired pressure is reached push knob in to lock in place.

UNIVERSAL QUICK CONNECT BODIES

The universal quick connect body (E) accepts the three most popular

styles of quick connect plugs: Industrial, automotive, and ARO. One

hand push-to-connect operation makes connections simple and

easy. The two quick connect bodies allow the use of two tools at the

same time.

DRAIN VALVE

The drain valve (B) is located at the base of

B

the air tank and is used to drain

condensation at the end of each use.

See

Draining Air Tank under Maintenance.

COOLING SYSTEM

This compressor contains an advanced design cooling system.

It is normal for this fan to blow air through the vent holes in large

amounts. The cooling system is working when air is expelled.

10



AIR COMPRESSOR PUMP

The pump compresses air into the air tank. Working air is not

available until the compressor has raised the air tank pressure

above that required at the air outlet.

AIR INTAKE FILTER

The filter (J) is designed to clean air entering the

J

pump. To ensure the pump continually receives a

clean, cool, and dry air supply the filter must always

be clean and the filter intake must be free from

obstructions.

MOTOR OVERLOAD PROTECTOR

The motor has an automatic reset thermal overload protector. If the

motor overheats for any reason, the overload protector will shut off

the motor. The motor must be allowed to cool down before restarting.

The compressor will automatically restart after the motor cools.





INSTALLING HOSES

WARNING: Risk of unsafe operation. Firmly grasp hose in hand

when installing or disconnecting to prevent hose whip.

1. Ensure regulated pressure gauge reads 0 PSI.

2. Grasp the hose at the quick connect plug and push the plug

into the quick connect body (E). Coupler will snap into place.

3. Grasp the hose and pull to ensure coupler is seated.

DISCONNECTING HOSES

WARNING: Risk of unsafe operation. Firmly grasp hose in hand

when installing or disconnecting to prevent hose whip.

1. Ensure regulated pressure gauge reads 0 PSI (0 kPa).

2. Push coupler on quick connect body back to release quick

connect plug on hose.



WARNING: Risk of electrical shock. In the event of a short

circuit, grounding reduces the risk of shock by providing an escape

wire for the electric current. This air compressor must be properly

grounded.

The portable air compressor is equipped with a cord having a

grounding wire with an appropriate grounding plug.

1. The cord set and plug (M) with this unit

N

M

O

contains a grounding pin (N). This plug

MUST be used with a grounded

outlet (O).

IMPORTANT: The outlet being used must

be installed and grounded in accordance

with all local codes and ordinances.

2. Ensure the outlet being used has the same configuration as the

grounded plug. DO NOT USE AN ADAPTER.

3. Inspect the plug and cord before each use. Do not use if there

are signs of damage.

4. If these grounding instructions are not completely understood, or

if in doubt as to whether the compressor is properly grounded,

have the installation checked by a qualified electrician.

DANGER: Risk of electrical shock. IMPROPER GROUNDING

CAN RESULT IN ELECTRICAL SHOCK.

• Do not modify the plug provided. If it does not fit the available

outlet, a correct outlet should be installed by a qualified

electrician.

• Repairs to the cord set or plug MUST be made by a qualified

electrician.

11





If an extension cord must be used, be sure it is:

 • a3wireextensioncordthathasa3bladegroundingplug,and

a 3-slot receptacle that will accept the plug on the product

 • ingoodcondition

 • plugisnotworn

 • nolongerthan50feet(15.2m)

 • 12gauge(AWG)orlarger.(Wiresizeincreasesasgaugenum-

ber decreases. 10 AWG and 8 AWG may also be used. DO NOT

USE 14 OR 16 AWG.)

CAUTION: The use of an undersized extension cord will cause volt-

age to drop resulting in power loss to the motor and overheating.

Instead of using an extension cord, increase the working reach of

the air hose by attaching another length of hose to its end. Attach

additional lengths of hose as needed. Always use a minimum 3/8"

(9.5 mm) or greater air hose rated at 300 PSI.



Refer to the Voltage and Minimum Branch Circuit Requirements

under Specifications.

CAUTION: Certain air compressors can be operated on a

15 amp circuit if the following conditions are met.

• Voltage supply to circuit must comply with the National

Electrical Code.

• Circuitisnotusedtosupplyanyotherelectricalneeds.

• Extensioncordscomplywithspecifications.

• Circuitisequippedwitha15ampcircuitbreakeror15amp

time delay fuse. NOTE: If compressor is connected to a circuit

protected by fuses, use only time delay fuses. Time delay

fuses should be marked “D” in Canada and “T” in the U.S.

If any of the above conditions cannot be met, or if operation of the

compressor repeatedly causes interruption of the power, it may be

necessary to operate it from a 20 amp circuit. It is not necessary to

change the cord set.



NOTE: Always use an air line filter to remove moisture and oil vapor

when spraying paint.



Place the air compressor in a clean, dry and well ventilated area

at least 12" (30.5 cm) away from the wall or other obstructions that

will interfere with the flow of air. Keep the compressor away from

areas that have dirt and/or volatile fumes in the atmosphere. These

impurities may clog the intake filter and valves, causing inefficient

operation.

WARNING: The air compressor pump and shroud are designed

to allow for proper cooling. The ventilation openings on the com-

pressor are necessary to maintain proper operating temperature.

Do not place rags or other containers on or near these openings.

Place the air compressor on a flat surface resting on the wheels

and rubber foot.

ELECTRICAL

Refer to all safety instructions before using unit. Observe extension

cord safety instructions, if necessary. Always move the On/Auto/Off

switch (L) to the OFF position before removing the plug from the

outlet.

12





When transporting the compressor in a vehicle,

A

C

trailer, etc. ensure that the air tank is drained and

theunitissecuredandplacedonaflathorizontal

surface. Use care when driving so to avoid

tipping the unit over in the vehicle. Damage can

occur to the unit or surrounding items if unit is

tipped. Storecompressorinaverticalorhorzitionalposition.

LIFTING

Always use two people when lifting and lift from the recommended

lift points A and C.

MOVING

1. Support compressor and pull handle (A) until fully extended (lock

position).

A

WARNING: Risk of unsafe operation. Ensure proper footing and

use caution when rolling compressor so that unit does not tip or

cause loss of balance.

2. To move, roll compressor on tires using handle (A) as shown.





1.

Ensure the On/Auto/Off switch (L) is in the OFF position.

2.

Plug the power cord into the correct branch circuit receptacle.

See

Voltage and Circuit Protection under Installation.

3. Ensure air tank is drained, see Draining Air Tank under

Maintenance.

4. Ensure the drain valve (

B

) is closed.

5. Ensure safety valve (

G

) is functioning properly, see Checking

Safety Valve under Maintenance.

6. Pull the regulator knob (F) out and turn counterclockwise until fully

closed. Ensure regulated pressure gauge reads 0 PSI. Push knob

in to lock in place.

7

. Attach hose and accessories. NOTE: Always use a mini-

mum 3/8" (9.5 mm) or greater air hose rated at 300 PSI.

WARNING: Risk of unsafe operation. Firmly grasp air hose in hand

when installing or disconnecting to prevent hose whip.

WARNING:

Risk of unsafe operation. Do not use damaged or worn

accessories.

WARNING: Risk of Bursting. Too much air pressure causes a

hazardous risk of bursting. Check the manufacturer’s maximum

pressure rating for air tools and accessories. The regulator outlet

pressure must never exceed the maximum pressure rating.





WARNING: Do not operate this unit until you read and understand

this instruction manual for safety, operation and maintenance

instructions.

BREAK-IN PROCEDURE

CAUTION: Risk of unsafe operation. Do not operate in vertical

position.Verticalpositionisforstorageonly.

CAUTION: Risk of property damage. Serious damage may result if

the following break-in instructions are not closely followed.

This procedure is required before the air compressor is put into

service for the first time and when the check valve or a compressor

pump/motor has been replaced.

1. Ensure the On/Auto/Off switch (L) is in the OFF position.

13



NOTE: If hose is not connected to Quick Connect body, pull coupler

back until it clicks to prevent air from escaping through the quick

connect.

2.

Plug the power cord into the correct branch circuit receptacle.

See

Voltage and Circuit Protection under Installation.

3. Open the drain valve (turn lever counter-clockwise) fully to

permit air to escape and prevent air pressure build up in the air

tank during the break-in period.

4. Move the On/Auto/Off switch to the ON position. The compressor

will start.

5. Run the compressor for 15 minutes.

6. After 15 minutes, close the drain valve by turning lever

clockwise. The tank will fill to cut-out pressure and the motor

will stop.

7. Compressed air will be available until it is used or bled off.





1. Follow Pre-Start Checklist under Preparation for Use.

CAUTION: Risk of unsafe operation. Do not operate in vertical

position.Verticalpositionisforstorageonly.

2. Move the On/Auto/Off switch to the ON position and allow tank

pressure to build. Motor will stop when tank pressure reaches

cut-out pressure.

CAUTION: Risk of unsafe operation. Compressed air from the

unit may contain wa ter condensation and oil mist. Do not spray

un fil tered air at an item that could be damaged by moisture. Some

air op er ated tools or de vic es may require filtered air. Read the

in struc tions for the air tool or device.

 3.Adjust regulator (F) to desired setting. See Regulator under

Features.



1. Move On/Auto/Off switch (L) to the OFF position. NOTE: If

finished using compressor, follow Steps 2 - 6.

2. Pull the regulator knob (F) out and turn counterclockwise until fully

closed. Ensure regulated pressure gauge reads 0 PSI. Push knob

in to lock in place.

3. Remove hose and accessory.

WARNING: Risk of unsafe operation. Firmly grasp air hose in hand

when installing or disconnecting to prevent hose whip.

4. Drain the air tank,

see Draining Air Tank under Maintenance

.

Ensure air tank pressure gauge reads 0 PSI.

WARNING: Risk of bursting. Drain air tank daily. Water will

condense in air tank. If not drained, water will corrode and weaken

the air tank causing a risk of air tank rupture.

5. Allow the compressor to cool down.

 6.Wipe air compressor clean and store in a safe, nonfreezing

area.



The following procedures must be followed when maintenance or

service is performed on the air compressor.

1. Ensure On/Auto/Off switch is in the OFF position.

2. Remove air compressor plug from outlet.

3. Drain air tank.

4. Allow air compressor to cool down before starting service.

NOTE: All compressed air systems contain maintenance parts (e.g.,

oil, filters, separators) that are periodically replaced. These used parts

may contain substances that are regulated and must be disposed of in

accordance with local, state, and federal laws and regulations.

NOTE: Take note of the positions and locations of parts during

disassembly to make reassembly easier.

14



NOTE: Any service operations not included in this section should

be performed by a D

e

WALT factory service center or a D

e

WALT

authorizedservicecenter.



Procedure Daily Weekly

Check safety valve

X

Inspect air filter

X

Drain air tank

X

Check for unusual noise/

vibration

X

Check for air leaks*

X

Clean compressor exterior

X

*Tocheckforairleaksapplyasolutionofsoapywateraroundjoints.

While compressor is pumping to pressure and after pressure cuts

out, look for air bubbles to form.



WARNING: Risk of bursting. If the safety valve does not work

properly, over-pressurization may occur, causing air tank rupture or

an explosion.

WARNING: Risk from flying objects. Always wear certified safety

equipment: ANSI Z87.1 eye protection (CAN/CSA Z94.3) with side

shields when using the compressor.

Before starting compressor, pull the ring on the safety valve to

make sure that the safety valve operates freely. NOTE: Ring may

be difficult to pull when air tank pressure is at 0 PSI. If the valve is

stuck or does not operate smoothly, it must be replaced with the

same type of valve.



WARNING: Risk of unsafe operation. Risk from noise. Air tanks

contain high pressure air. Keep face and other body parts away from

outlet of drain. Use eye protection [ANSI Z87.1 (CAN/CSA Z94.3)]

when draining as debris can be kicked up into face.

WARNING: Risk from noise. Use ear protection [ANSI S12.6

(S3.19)] as air flow noise is loud when draining.

NOTE: All compressed air systems generate condensate that

accumulates in any drain point (e.g. tanks, filter, aftercoolers, dryers).

This condensate contains lubricating oil and/or substances which

may be regulated and must be disposed of in accordance with local,

state, and federal laws and regulations.

1. Ensure On/Auto/Off switch is in the OFF position.

2. Lift compressor into an inclined position so drain valve (B) is at

the lowest point (this will assist in removing moisture, dirt, etc.

from air tanks).

3. Place a suitable container under the drain valve to catch

discharge.

4. Grasp lever on drain valve.

5. Slowly rotate lever to gradually bleed air from air tank.

WARNING: Risk of bursting. Drain air tank daily. Water will con-

dense in air tank. If not drained, water will corrode and weaken the

air tank causing a risk of air tank rupture.

CAUTION: Risk of property damage. Drain water from air tank may

contain oil and rust, which can cause stains.

6. When air tank pressure gauge reads 10 PSI, rotate valve to the

fully open position.

7. Close drain valve when finished.

15





WARNING: Hot surfaces. Risk of burn. Outlet tube, pump head,

and surrounding parts are very hot, do not touch. Allow compressor

to cool prior to servicing.

1. Ensure On/Auto/Off switch (L) is in the OFF Position.

2. Allow unit to cool.

3. Remove filter cover (J) from filter base.

J

4. Remove element from filter base.

5. Place new element back in filter base. Purchase

replacement parts from your local dealer or

authorized service center. Always use identical replacement

parts.

6. Snap filter cover to filter base.

CAUTION: Risk of unsafe operation. Do not operate without air

inlet filter



WARNING: The use of any other accessory not recommended for

use with this tool could be hazardous. Use only accessories rated

equal to or higher than the rating of the air compressor.

Recommended accessories for use with your tool are available

for purchase from your local dealer or authorized service center.

If you need assistance in locating any accessory for your tool,

please contact D

e

WALT Industrial Tool Co., 701 East Joppa Road,

Baltimore, MD 21286, call 1-800-4-D

e

WALT (1-800-433-9258) or visit

our website www.dewalt.com.



Please have the following information available for all service calls:

Model Number ____________ Serial Number _________________

Date and Place of Purchase ______________________________



To assure product SAFETY and RELIABILITY, repairs, maintenance

andadjustmentshouldbeperformedbyaD

e

WALT factory service

center, a D

e

WALT authorized service center or other qualified

service personnel. Always use identical replacement parts.



DeWALT heavy duty industrial tools are warranted for one year from

date of purchase. We will repair, without charge, any defects due

to faulty materials or workmanship. For warranty repair information,

call 1-800-4-D

e

WALT. This warranty does not apply to accessories

or damage caused where repairs have been made or attempted by

others. This warranty gives you specific legal rights and you may

have other rights which vary in certain states or provinces.

LATIN AMERICA: This warranty does not apply to products sold

in Latin America. For products sold in Latin America, see country

specific warranty information contained either in the packaging, call

the local company or see website for warranty information.

16



FREE WARNING LABEL REPLACEMENT: If your warning labels

become illegible or are missing, call 1-800-4-D

e

WALT for a free

replacement.

WARNING

DRAIN TANK DAILY

OR AFTER EVERY 4 HOURS OF USE. CONDENSATION BUILD-UP MAY CAUSE

CO RROSION INSIDE TANK RESULTING IN TANK FAILURE. SEE MANUAL FOR INSPECTION PROCEDURES.

TO DRAIN TANK OPEN VA LVE SLOWLY AND TIL T COMPRESSOR TO EMPTY A CCUMULATED W A TER.

ADVERTENCIA

DRENE EL TANQUE A DIARIO O DESPUÉS DE CADA 4 HORAS DE USO. LA ACUMULACIÓN DE

CONDENSACIÓN PUEDE OCASIONAR CORROSIÓN DENTRO DEL TANQUE Y PROVOCAR F A LLA DEL

TANQUE. CONSULTE EL MANUAL P A RA CONOCER LOS PROCEDIMIENTOS DE INSPECCIÓN. P A RA DRENAR EL TANQUE, ABRA LA

V Á LVULA LENT A MENTE E INCLINE EL COMPRESOR P A RAELIMINAR EL A GU A ACUMULAD A.

AVERTISSEMENT

RÉSERVOIR DE VIDANGE QUOTIDIEN OU APRÈS TOUTES LES 4 HEURES D'UTILISATION.

L'HABILLAGE DE CONDENSATION PEUT CAUSER LA CORROSION À L'INTÉRIEUR DU RÉSERVOIR A Y ANT

POUR RÉSUL T A T L'ÉCHEC DE RÉSERVOIR. VOIR LE MANUEL POUR DES PROCÉDURES D'INSPECTION. À LA VA L V E

OUVERTE DE RÉSERVOIR DE VIDANGE LENTEMENT ET A U C O MPRESSEUR D'INCLINAISON À L ' EAU AC CUMULÉE VIDE.

W A RNING HOT SURFACES

ADVERTENCIA

SUPERFICIES CALIENTES

A V ERTISSEMENT

SURFACES CHAUDES

DO NO T O PE RAT E I N U P RI G HT

PO S IT I ON . U P RI G HT PO S IT I ON

IS FO R S TO R AG E O N LY .

no op e re la he r rami en ta e n

po s ic i ón ve rtica l . Só lo

al m a cen e e n e s ta p o si c ió n .

ne pas f air e f o ncti o nn e r e n p os i ti o n

ve rtical e . L a p os i ti o n v e rtical e e s t

ré s e rvée au sto c kage u n iq u em e n t.

DO NOT ADJUST F A CTORY SETTINGS.

TO REDUCE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER.

Pres sure controls set at f actory for

maximum safe operation.

NO HAG A CA MB IOS E N LOS A JU ST ES

DE FÁBR IC A. NO R ET IR E LA T A P A P A RA

RED UCI R EL R IE SGO D E CH OQ UE EL ÉC TR IC O .

Los c on tr ole s de p re sió n se a ju sta n en l a

fáb ric a pa ra m áxi ma s eg ur ida d en l a ope ra ci ón .

ADVERTENCIA

WARNING

AVERTISSEMENT

NE PAS MO DI FIE R LE S RÉ GLA GE S DE L'U SIN E. N E PAS

RET IR ER LE C OUV ER CL E AF IN DE R ÉD UI RE LE S RI SQ UES

DE CHO CS É LE CT RI QU ES.

La pre ss io n es t r ég lé e en us in e a n de ma xi mi se r l a

séc uri té d e fon ct io nn em en t.



CFM: Cubic feet per minute.

SCFM: Standard cubic feet per minute; a unit of measure of air

delivery.

PSI: Pounds per square inch; a unit of measure of pressure.

kPa (kilopascal): Metric pressure measurement. 1 kilopascal

equal 1000 pascals.

Code Certification: Products that bear one or more of the

following marks: UL, CUL, ETL, CETL, have been evaluated by

OSHA certified independent safety laboratories and meet the

applicable Standards for Safety.

Cut-In Pressure: While the motor is off, air tank pressure drops

when accessory is used. When the tank pressure drops to a certain

low level the motor will restart automatically. The low pressure at

which the motor automatically restarts is called cut-in pressure.

Cut-Out Pressure: When an air compressor is turned on and

begins to run, air pressure in the air tank begins to build. It builds

to a certain high pressure before the motor automatically shuts

off, protecting your air tank from pressure higher than its capacity.

The high pressure at which the motor shuts off is called cut-out

pressure.

Branch Circuit: The circuit carrying electricity from electrical panel

to outlet.

Duty Cycle: This air compressor pump is capable of running

continuously. However, to prolong the life of your air compressor,

it is recommended that a 50%-75% average duty cycle be

maintained; that is, the air compressor pump should not run more

than 30-45 minutes in any given hour.

17





This section provides a list of the more frequently encountered malfunctions, their causes and corrective actions. The operator or maintenance

personnel can perform some corrective actions, and others may require the assistance of a qualified D

eWALT technician or your dealer.

Problem Code

Excessive air tank pressure-safety valve pops off ......................................................................1, 2

Air leaks ....................................................................................................................................3

Air leaks in air tank or at air tank welds ....................................................................................4

Air leaks between head and valve plate ....................................................................................5

Air leaks from safety valve .........................................................................................................6

Knocking Noise ..........................................................................................................................11

Pressure reading on the regulated pressure gauge drops when an accessory is used ...........7

Compressor is not supplying enough air to operate accessories..............................................8, 9, 10, 11, 12, 21

Regulator knob has continuous air leak ....................................................................................13

Regulator will not shut off air outlet ...........................................................................................13

Motor will not run .......................................................................................................................11, 14, 15, 16, 17, 18, 19, 20



CODE POSSIBLE CAUSE POSSIBLE SOLUTION

1 Pressure switch does not shut off motor when com-

pressor reaches cut-out pressure

Set the On/Auto/Off switch to OFF, if the unit does not shut off

contact a D

e

WALT factory service center or a D

e

WALTauthorized

service center.

2 Pressure switch cut-out too high Contact a D

e

WALT factory service center or a D

e

WALT autho-

rizedservicecenter.

3 Tube fittings are not tight enough Tighten fittings where air can be heard escaping. Check fittings

with soapy water solution. Do Not Overtighten.

18



CODE POSSIBLE CAUSE POSSIBLE SOLUTION

4 Defective air tank Air tank must be replaced. Do not repair the leak.

WARNING: Risk of bursting. Do not drill into, weld or otherwise

modify air tank or it will weaken. The air tank can rupture or

explode.

5 Leaking seals Contact a D

e

WALT factory service center or a D

e

WALT autho-

rizedservicecenter.

6 Defective safety valve Operate safety valve manually by pulling on ring. If valve still

leaks, it must be replaced.

7

Regulatorisnotadjustedcorrectlyforaccessory

being used

It is normal for some pressure drop to occur when an accessory

isused,adjusttheregulatorasinstructedinRegulator under

Features if pressure drop is excessive.

NOTE:Adjusttheregulatedpressureunderflowconditions

while accessory is being used.

8 Prolonged excessive use of air Decrease amount of air usage.

9 Compressor is not large enough for accessory Check the accessory air requirement. If it is higher than the

CFM or pressure supplied by your air compressor, a larger com-

pressor is needed to operate accessory.

10 Hole in air hose Replace air hose.

11 Check valve restricted Remove, clean or replace.

12 Air leaks Tighten fittings.

13 Regulator is damaged Replace.

14 Motor overload protection switch has tripped Refer to Motor Overload Protection under Features. If motor

overload protection trips frequently, contact a D

e

WALT factory

service center or a D

e

WALTauthorizedservicecenter.

19



CODE POSSIBLE CAUSE POSSIBLE SOLUTION

15 Tank pressure exceeds pressure switch cut-in

pressure

Motor will start automatically when tank pressure drops below

cut-in pressure of pressure switch.

16 Extension cord is wrong length or gauge Check for proper gauge wire and cord length. Refer to the

Extension Cords paragraph in the Installation section.

17 Loose electrical connections Contact a D

e

WALT factory service center or a D

e

WALT autho-

rizedservicecenter.

18 Possible defective motor Contact a D

e

WALT factory service center or a D

e

WALT autho-

rizedservicecenter.

19 Paint spray on internal motor parts Contact a D

e

WALT factory service center or a D

e

WALTauthorized

service center. Do not operate the compressor in the paint spray

area. See flammable vapor warning.

20 Fuse blown, circuit breaker tripped 1. Check fuse box for blown fuse and replace as necessary.

Reset circuit breaker. Do not use a fuse or circuit breaker with

higher rating than that specified for our particular branch cir-

cuit.

2. Check for proper fuse. You should use a time delay fuse.

3. Check for low voltage conditions and/or proper extension

cord.

4. Disconnect the other electrical appliances from circuit or oper-

ate the compressor on its own branch circuit.

21 Restricted air intake filter Clean or replace air intake filter. Do not operate the air

compressor with the filter removed. Refer to the Air Filter

paragraph in the Maintenance section.



20



Tension : monophasé, 120V

Exigence minimale du circuit de dérivation : 15 A

Type de fusible : temporisation



MODÈLE

D55171

POIDS

57,2 kg (126 lbs.)

HAUTEUR

457,2 mm (18,0 po)

LARGEUR

609,6 mm (24,0 po)

LONGUEUR

838,2 mm (33,0 po)

CAPACITÉ DU RÉSERVOIR D’AIR

(GALLONS)

7,5 (28,4 liters)

PRESSION D’ENCLENCHEMENT

APPROX.

145 PSI

ENV. PRESSION DE DÉCLENCHEMENT

175 PSI

PI

3

/MIN STANDARD À 90 PSI

*4,6

NIVEAU SONORE

+74,0 dBA

* Testé conformément à la norme ISO 1217

+ Testé conformément à la norme ISO 3744

A. Poignées coulissantes

B. Robinet de purge

C. Appui de rangement

D. Régulateur de pression

E. Branchements rapides

F. Régulateur

G. Soupape de sûreté

H. Manocontacteur

I. Rembobineur de cordon

d’alimentation

J. Filtre d’admission d’air

K. ManomÈtre de réservoir

L. Interrupteur marche arrêt





Valeur de l’émission de bruits

Niveau de pression acoustique : LpA = 74,0 dBA re 20μPA

Incertitude du niveau de

pression acoustique calculé : KpA = 3,0 dBA re 20μPA

Niveau de puissance acoustique : LwA = 87,0 dBA re 1 pw

Incertitude du niveau de puissance

acoustique : KwA = 3,0 dBA re 1 pw

La somme de la valeur de l’émission et de l’incertitude établit la

limite sous laquelle la valeur pour un seul outil y sera inférieure et

ce, à 95 % de fiabilité statistique.



FIG. 1

E

A

F

L

H

I

D

K

C

B

G

J

La page charge ...

DeWalt D55171 Manuel utilisateur

DeWalt D55171 Manuel utilisateur

dans d''autres langues

Documents connexes