LG WM3505CW Le manuel du propriétaire

Catégorie
Machines à laver
Taper
Le manuel du propriétaire
ESPAÑOLENGLISH FRANÇAIS
OWNER'S MANUAL
WASHING
MACHINE
Please read this owner's manual thoroughly before operating and keep it
handy for reference at all times. Operating Instructions are available on
the LG website at: https://us.smartthinq.com/images/pdfmanual/VH_FL_
VICTOR_799_MFL68005567_EN.pdf
WM3500CW
WM3505CW
MFL68005567
Rev.02_051718
www.lg.com
Copyright © 2018 LG Electronics Inc. All Rights Reserved.
WM3095CW
2
3 SAFETY INSTRUCTIONS
3 IMPORTANT SAFETY INSTRUCTIONS
7 PRODUCT OVERVIEW
7 Parts
7 Accessories
8 INSTALLATION
8 Tools Needed
8 Installation Overview
9 Product Specifications
10 Choosing the Proper Location
11 Unpacking and Removing Shipping Bolts
12 Connecting the Water Lines
13 Connecting the Drain Hose
14 Leveling the Washer
15 Connecting to the Power Supply
15 Testing the Washer
16 OPERATION
16 Using the Washer
17 Loading the Washer
TABLE OF CONTENTS
This manual contains an abbreviated Operation
section. For the complete Operation section, scan
the QR code below or visit: https://us.smartthinq.
com/images/pdfmanual/VH_FL_VICTOR_799_
MFL68005567_EN.pdf
18 SMART FUNCTIONS
18 LG SmartThinQ Application
21 Smart Diagnosis™ Function
22 MAINTENANCE
22 Regular Cleaning
24 Cleaning the Door Seal
24 Cleaning the Water Inlet Filters
25 Cleaning the Drain Pump Filter
26 Care in Cold Climates
27 TROUBLESHOOTING
27 FAQs: Frequently Asked Questions
28 Before Calling for Service
36 LIMITED WARRANTY
36 FOR USA
39 FOR CANADA
43 Warranty Exceptions (U.S. and Canada)
3SAFETY INSTRUCTIONS
ENGLISH
SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and
follow all safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or injure you and others.
All safety messages will follow the safety alert symbol and either the word WARNING or CAUTION.
These words mean:
WARNING
If you do not follow instructions, it could result in death or serious injury.
CAUTION
If you do not follow instructions, it could result in minor or moderate injury or damage to the product.
All safety messages tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell
you what may happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
WARNING
To reduce the risk of explosion, re, death, electric shock, scalding or injury
to persons when using this product, follow basic precautions, including the
following:
California Safe Drinking Water and Toxic Enforcement Act
This product contains chemicals known to the State of California to cause cancer and birth defects or other
reproductive harm. Wash hands after handling. (USA only)
INSTALLATION
Adhere to all industry recommended safety procedures including the use of long-sleeved gloves and safety
glasses.
Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has
missing or broken parts, including a damaged cord or plug.
Before use, the appliance must be properly installed as described in this manual.
To reduce the risk of severe injury or death, follow all installation instructions.
Refer to the INSTALLATION INSTRUCTIONS for detailed grounding procedures. Installation instructions
are packed with the appliance for the installer’s reference. If the appliance is moved to a new location, have
it checked and reinstalled by qualied service personnel.
Moving or installation of the appliance requires two or more people.
Do not install the appliance in humid spaces.
Store and install the appliance where it will not be exposed to temperatures below freezing or exposed to
outdoor weather conditions.
This appliance is not designed for maritime use or for mobile installations such as in RVs, trailers, or aircraft.
4 SAFETY INSTRUCTIONS
Keep packing materials out of the reach of children. Packaging material can be dangerous for children.
There is a risk of suffocation.
Destroy the carton, plastic bag, and other packing materials after the appliance is unpacked. Children might
use them for play. Cartons covered with rugs, bedspreads, or plastic sheets can become airtight chambers.
The appliance must be installed and electrically grounded by qualied service personnel in accordance with
local codes.
Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.
When installing or moving the appliance, be careful not to pinch, crush, or damage the power cord.
Connect to a properly rated, protected, and sized power circuit to avoid electrical overload.
This appliance must be positioned near to an electrical power supply.
Disconnect the power cord, house fuse or circuit breaker before installing or servicing the appliance.
The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard
3-prong (grounding) wall outlet to minimize the possibility of electric shock from this appliance.
Use new hoses when connecting the appliance to the water supply. Do not reuse old hoses.
OPERATION
Read all instructions before using the appliance and save these instructions.
Use this appliance only for its intended purpose.
If the product has been submerged, contact an LG Electronics customer information center for instructions
before resuming use.
If you detect a strange sound, a chemical or burning smell, or smoke coming from the appliance, unplug it
immediately, and contact an LG Electronics customer information center.
Under certain conditions, hydrogen gas may be produced in a hot-water system that has not been used
for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot-water system has not been used for
such a period, before using the appliance turn on all hot water faucets and let the water ow from each for
several minutes. This will release any accumulated hydrogen gas. As the gas is ammable, do not smoke or
use an open ame during this time.
Do not reach into the washer if the tub or drum, agitator, or any interior parts are moving. Before loading,
unloading, or adding items, press Start/Pause and allow the tub or drum to coast to a complete stop before
reaching inside.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning the use of the appliance by a person responsible for their safety.
Do not allow children or pets to play on, in or with the appliance. Close supervision is necessary when the
appliance is used near children or pets.
Keep laundry products out of children’s reach. To prevent injury to persons, observe all warnings on product
labels.
Repair or immediately replace all power cords that have become frayed or otherwise damaged. Do not use
a cord that shows cracks or abrasion damage along its length or at either end.
Never unplug the appliance by pulling on the power cord. Always grip the plug rmly and pull straight out
from the outlet.
Do not use an extension cord or adapter with this appliance.
Do not grasp the power cord or touch the appliance controls with wet hands.
Do not modify or extend the power cord.
5SAFETY INSTRUCTIONS
ENGLISH
If the electrical supply cord is damaged, it must only be replaced by the manufacturer or its service agent or
a similar qualied person in order to avoid a hazard.
Do not put oily or greasy clothing, candles or ammable materials on top of the appliance.
Keep the area underneath and around your appliances free of combustible materials (lint, paper, rags, etc.),
gasoline, chemicals and other ammable vapors and liquids.
Do not store or use gasoline or other ammable vapors and liquids in the vicinity of this or any other
appliance.
Do not mix chlorine bleach with ammonia or acids such as vinegar. Follow package directions when using
laundry products. Incorrect usage can produce poisonous gas, resulting in serious injury or death.
Never use harsh chemicals, abrasive cleaners, or solvents to clean the washer. They will damage the nish.
Do not wash articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline,
dry-cleaning solvents, vegetable or cooking oil, or other ammable or explosive substances, as they give off
vapors that could ignite or explode.
Do not add gasoline, dry cleaning solvents, or other ammable or explosive substances to the wash water.
These substances give off vapors that could ignite or explode.
In the event of a gas leak (propane gas, LP gas, etc.) do not operate this or any other appliance. Open a
window or door to ventilate the area immediately.
Do not tamper with controls.
Fix the drain hose securely in place to avoid ooding.
Do not abuse, sit on, or stand on the door of the appliance.
MAINTENANCE
Do not repair or replace any part of the appliance. All repairs and servicing must be performed by qualied
service personnel unless specically recommended in this owner’s manual. Use only authorized factory
parts.
Disconnect this appliance from the power supply before cleaning and attempting any user maintenance.
Turning the controls to the OFF position does not disconnect this appliance from the power supply.
Remove any dust or foreign matter from the power plug pins.
Do not disassemble or repair the appliance by yourself.
Remove the door before the appliance is removed from service or discarded to avoid the danger of children
or small animals getting trapped inside.
Make sure the dispenser drawer or lid is closed at all times when not being lled with laundry products.
GROUNDING INSTRUCTIONS
Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with
a qualied electrician or service personnel if you are in doubt whether the appliance is properly grounded.
Do not modify the plug provided with the appliance; if it will not t the outlet, have a proper outlet installed by
a qualied electrician.
The appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk
of electric shock by providing a path of least resistance for electric current. The appliance is equipped with
a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an
appropriate outlet that is installed and grounded in accordance with all local codes and ordinances.
6 SAFETY INSTRUCTIONS
CAUTION
To reduce the risk of minor or moderate injury to persons, malfunction, or damage
to the product or property when using this product, follow basic precautions,
including the following:
INSTALLATION
Install the product on a rm and level oor.
OPERATION
Do not place objects on top of the appliance.
Turn off the water faucets and unplug the appliance if the appliance is to be left for an extended period of
time, such as during vacations.
ALWAYS follow the fabric care instructions supplied by the garment manufacturer.
Use fabric softeners or products to eliminate static only as recommended by the manufacturer.
Do not combine laundry products for use in one load unless specied on the label.
Do not touch draining water which may be hot.
If the drain hose and the water supply hose are frozen in winter, defrost them before using the appliance.
Do not store or spill liquid detergents, cleaners, or bleaches (chlorine bleach, oxygen bleach) on the
appliance. Doing so may result in corrosion, discoloration or damage to the surface of the appliance.
Clothing or articles that are waterproof or water resistant must be washed in the Waterproof cycle only.
(e.g. water resistant clothing, mattress covers, outdoor clothes, plastic mats, etc.) Otherwise, it may result
in personal injury or damage to the washer, clothes, walls, oor, and surrounding objects due to abnormal
vibration.
SAVE THESE INSTRUCTIONS
7PRODUCT OVERVIEW
ENGLISH
PRODUCT OVERVIEW
Parts
13
12
1
Control Panel
4
Drum
7
Drain Pump Filter Cover
10
Water Inlets
2
Detergent Dispenser
Drawer
5
Door
8
Drain Pump Filter
11
Shipping Bolts
3
Door Seal
6
Leveling Feet
9
Drain Hose
12
Power Cord
13
Drain Hose
Accessories
Included Accessories
Non-skid pads
Hole caps (4)
Wrench
Tie strap
Elbow bracket
(for securing drain
hose)
Required Accessories
Hot/cold water hoses
(sold separately)
Optional Accessories
Pedestal or Pedestal washer
(sold separately)
Stacking Kit
(sold separately)
NOTE
The images in this guide may be different from the actual components and accessories, which are subject to
change by the manufacturer without prior notice for product improvement purposes.
For your safety and for extended product life, use only authorized components. The manufacturer is not
responsible for product malfunction or accidents caused by the use of separately purchased unauthorized
components or parts.
8 INSTALLATION
INSTALLATION
Tools Needed
Pliers
Level
Installation Overview
Please read the following installation instructions rst after purchasing this product or transporting it to another
location.
TEST!
Choosing the proper location
Unpacking and removing
shipping bolts
Connecting the water lines
Connecting the drain line
Leveling the washer Connecting to the power
supply
Testing the washer
9INSTALLATION
ENGLISH
Product Specications
The appearance and specications listed in this manual may vary due to constant product improvements.
Electrical requirements 120 VAC @ 60 Hz
Min. / Max. water pressure 20 – 120 psi (138–827 kPa)
Dimensions
70 cm(W) X 77 cm(D) X 99 cm(H), 139.6 cm (D with door open)
27”(W) X 30 ¼”(D) X 39”(H), 55” (D with door open)
Net weight 187.4 lb (85 kg)
Max spin speed 1300 RPM
WARNING
Moving or installation of the appliance requires two or more people. Failure to follow these instructions may
result in injury.
Store and install the appliance where it will not be exposed to temperatures below freezing or exposed to
outdoor weather conditions. Failure to follow this warning can cause product or part failure, serious injury,
re, electric shock, or death.
Properly ground the washer to conform with all governing codes and ordinances. Failure to follow this
warning can cause serious injury, re, electric shock, or death.
To reduce the risk of electric shock, do not install the appliance in humid spaces. Failure to follow this
warning can cause serious injury, re, electric shock, or death.
To ensure proper airow, do not block the large opening on the bottom of the washer with carpeting or other
materials.
Do not remove the ground prong. Do not use an adapter or extension cord. Plug into a grounded 3-prong
outlet. Failure to follow this warning can cause serious injury, re, electric shock, or death.
Certain internal parts are intentionally not grounded and may present a risk of electric shock only during
servicing. Service personnel - Do not contact the following parts while the appliance is energized: pump,
valve, motor, control board.
10 INSTALLATION
Choosing the Proper
Location
Install the washer on a solid oor that is strong and
rigid enough to support the weight of the washer,
even when fully loaded, without exing or bouncing.
If the oor has too much ex, you may need to
reinforce it to make it more rigid. If the oor is not
solid, it may cause severe vibration and noise.
NOTE
Before installing the washer, make sure the oor
is clean, dry and free of dust, dirt, water and oil so
the washer feet cannot slide easily. Leveling feet
that can move or slide on the oor can contribute to
excess vibration and noise due to poor contact with
the oor.
If a drip pan must be used, take extra care to follow
the instructions provided with the drip pan and make
sure the leveling feet are adjusted for rm and even
contact with the pan. Use of drip pans and failure to
properly level the machine may result in increased
vibration and noise during operation.
Allow for sufcient space between the walls and the
washer for installation.
Power Outlet
The power outlet must be within 60 inches (1.5 m)
of either side of the washer.
The appliance and outlet must be positioned so that
the plug is easily accessible.
Do not overload the outlet with more than one
appliance.
The outlet must be grounded in accordance with
current electrical wiring codes and regulations.
Use a time-delay fuse or circuit breaker.
NOTE
It is the personal responsibility and obligation of the
product owner to have a proper outlet installed by
qualied service personnel.
Flooring
To minimize noise and vibration, the washer must
be installed on a solidly constructed oor.
Allowable slope under the entire washer is a
maximum 1 inch (2.5 cm) difference from side to
side or from front to back.
Installing on carpeting and soft tile surfaces is not
recommended.
Never install the washer on a platform or weakly
supported structure.
NOTE
The washer must be installed on rm ooring to
minimize vibration during the spin cycle. Concrete
ooring is best, but a wood oor is sufcient,
provided it is built to FHA standards.
Floor Installation
(70 cm)(2.5 cm) (2.5 cm)
27"
1" 1"
(0.5 cm
)
13
64
4"
(10 cm)
(62.6 cm)
(77 cm)
55"
(139.6 cm)
24
¾
30
¼
To ensure sufcient clearance for water lines, the
drain line and airow, allow minimum clearances of
at least 1 inch (2.5 cm) at the sides and 4 inches (10
cm) behind the unit. Be sure to allow for wall, door,
or oor moldings that may increase the required
clearances.
Stacked or Pedestal Installation
30 ¼"
(77 cm)
4"
(10 cm)
27"
(70 cm)
1"
(2.5 cm)
1"
(2.5 cm)
77 ½"
(196.8 cm)
(0.5 cm)
13
64
NOTE
Refer to the instructions packaged with the optional
pedestal kit before installing with a pedestal kit.
Do not use a drip pan with a pedestal or pedestal
washer installation as it can block the drawer. Using
a drip pan may result in increased vibration and
noise during operation.
11INSTALLATION
ENGLISH
Unpacking and Removing
Shipping Bolts
Unpack all shipping materials from the washer for
proper operation and inspect it for shipping damage.
CAUTION
Failure to remove shipping materials can cause
excessive noise and vibration.
1
Lift the washer off the foam base.
After removing the carton and shipping material,
lift the washer off the foam base. Make sure the
plastic tub support comes off with the base and is
not stuck to the bottom of the washer.
If you must lay the washer down to remove the
base packaging materials, always protect the side
of the washer and lay it carefully on its side. Do
not lay the washer on its front or back.
Foam tub
support
Carton base
2
Remove the bolt assemblies.
Starting with the bottom two shipping bolts, use
the wrench (included) to fully loosen all four
shipping bolts by turning them counterclockwise.
Remove the bolt assemblies by wiggling them
slightly while pulling them out.
Retainer
Shipping
bolt
3
Install the hole caps.
Locate the four hole caps included in the
accessory pack and install them in the shipping
bolt holes.
Cap
NOTE
Save the bolt assemblies for future use. To prevent
damage to internal components, do not transport
the washer without reinstalling the shipping bolts.
Failure to remove shipping bolts and retainers may
cause severe vibration and noise, which can lead
to permanent damage to the washer. The cord is
secured to the back of the washer with a shipping
bolt to help prevent operation with shipping bolts in
place.
12 INSTALLATION
Connecting the Water Lines
To avoid the risk of costly water damage, purchase
and install new inlet hoses when installing the
washer.
1
Check the ttings and seals.
Inspect the threaded tting on each hose and
make sure there is a rubber seal in place in both
ends of each hose to prevent leaking.
Rubber seal Rubber seal
Water hose (to water
inlet on washer)
Water hose (to tap)
2
Connect the water supply hoses.
Connect the water supply hoses to the hot and
cold water faucets tightly by hand and then
tighten another 2/3 turn with pliers. Connect the
blue hose to a cold water faucet and the red hose
to a hot water faucet.
3
Flush out the inlet hoses.
After connecting the inlet hoses to the water
faucets, turn on the water faucets to ush out
foreign substances (dirt, sand or sawdust) in the
water lines. Let water drain into a bucket, and
check the water temperature to make sure you've
connected the hoses to the correct faucets.
4
Attach the water lines to the back of the
washer.
Attach the hot water line to the hot water inlet on
the back of the washer. Attach the cold water line
to the cold water inlet on the back of the washer.
Tighten the ttings securely. Turn ON both faucets
all the way and check for leaks at both ends of the
hoses.
Cold
water
inlet
Hot water
inlet
WARNING
Do not overtighten the hoses or cross-thread the
hose ttings. Overtightening or cross-threading
can damage the valves or couplings, resulting in
leaking and property damage.
Do not reuse old hoses. Use only new hoses
when installing the washer. Old hoses could leak
or burst causing ooding and property damage.
Contact an LG Customer Information Center for
assistance in buying hoses.
NOTE
Periodically check the hoses for cracks, leaks, and
wear, and replace the hoses every ve years. Do
not stretch the water hoses intentionally, and make
sure that they are not pinched, crushed or kinked by
other objects.
Water supply pressure must be between 20 psi
and 120 psi (138 – 827 kPa). If the water supply
pressure is more than 120 psi, a pressure reducing
valve must be installed.
To provide optimum washing performance, the hot
water temperature should be set at 120 – 130 °F
(48 – 54 °C) and the cold at 60 °F (15 °C).
The washer should never be installed or stored in a
location subject to freezing temperatures. Damage
to the water lines and internal mechanisms of the
washer can result. If the washer was exposed to
freezing temperatures prior to installation, allow it to
stand at room temperature for several hours before
use and check for leaks prior to operation.
Do not use ood-preventing hoses with auto shutoff
devices. The devices can be tripped during ll and
prevent the machine from lling properly.
13INSTALLATION
ENGLISH
Connecting the Drain Hose
Connect the drain hose to either a standpipe or
laundry tub.
NOTE
The drain hose should always be properly secured.
Failure to properly secure the drain hose can result
in ooding and property damage.
The drain must be installed in accordance with any
applicable local codes and regulations.
Make sure that the drain hose is not stretched,
pinched, crushed, or kinked.
Do not install the drain hose with the end lower than
29.5 inches (0.7 m) or higher than 96 inches
(2.4 m) above the bottom of the washer or more
than 60 inches (1.5 m) away from the washer.
Never create an airtight seal between the hose and
the drain with tape or other means. If no air gap
is present, water can be siphoned out of the tub
resulting in poor wash/rinse performance or clothing
damage.
Option 1: Standpipe
1
Clip the end of the hose into the elbow
bracket.
Connect the elbow bracket within 4 inches
(10 cm) of the end of the drain hose. If the drain
hose is extended more than 4 inches (10 cm)
beyond the end of the elbow bracket, mold or
microorganisms could spread to the inside of the
washer.
No more than
4 inches (10 cm)
Elbow bracket
2
Insert the end of the drain hose into the
standpipe.
Drain hose
Elbow bracket
3
Use a tie strap to secure the drain hose in
place.
Option 2: Laundry Tub
1
Clip the end of the hose into the elbow
bracket.
Connect the elbow bracket within 4 inches
(10 cm) of the end of the drain hose. If the drain
hose is extended more than 4 inches (10 cm)
beyond the end of the elbow bracket, mold or
microorganisms could spread to the inside of the
washer.
No more than
4 inches (10 cm)
Elbow bracket
2
Hang the end of the drain hose over the side
of the laundry tub.
Drain hose
Elbow bracket
3
Use a tie strap to secure the drain hose in
place.
14 INSTALLATION
Leveling the Washer
The drum of your new washer spins at very high
speeds. To minimize vibration, noise, and unwanted
movement, the oor must be a level, solid surface.
NOTE
Adjust the leveling feet only as far as necessary to
level the washer. Extending the leveling feet more
than necessary can cause the washer to vibrate.
Before installing the washer, make sure that the
oor is clean, dry and free of dust, dirt, water and
oil so the washer feet cannot slide easily. Feet
that move or slide on the oor can contribute to
excessive vibration and noise due to poor contact
with the oor.
1
Position the washer in its nal location.
Take special care not to pinch, strain, or crush the
water and drain lines. If you have a carpenter's
level, you can place it across the top of the
washer. The slope beneath the washer should not
exceed 1 inch, and all four leveling feet must rest
rmly on the oor.
Level
1"
2
Adjust the lower leveling feet.
Turn in one direction to raise the washer or the
other direction to lower it.
Raise Lower
3
Tighten the locknuts.
Turn the locknuts counter-clockwise and tighten
them when the washer is level.
Lock nut
Tighten all 4 lock
nuts securely
4
Recheck the washers levelness.
Push or rock the top edges of the washer gently
to make sure the washer does not rock. If the
washer rocks, repeat steps 1-3.
CAUTION
Using the washer without leveling it may cause
excess vibration and noise, leading to a machine
malfunction.
Extend the leveling feet only to level the washer.
If you extend the leveling feet unnecessarily, it
may cause abnormal vibration of the washer.
Using Non-Skid Pads
If you install the washer on a slippery surface, it
may move because of excessive vibration. Incorrect
leveling may cause malfunction through noise and
vibration. If this occurs, install the non-skid pads
under the leveling feet and adjust the level.
1
Clean the oor to attach the non-skid pads.
Use a dry rag to remove and clean foreign objects
or moisture. If moisture remains, the non-skid
pads may slip.
2
Adjust the level after placing the washer in the
installation area.
3
Place the adhesive side of the non-skid pad
on the oor.
It is most effective to install the non-skid pads
under the front leveling feet. If it is hard to place
the pads under the front leveling feet, place them
under the back leveling feet.
This side up
Adhesive
side
Remove backing
4
Recheck the washers levelness.
Push or rock the top edges of the washer gently
to make sure that the washer does not rock. If the
washer rocks, level the washer again.
15INSTALLATION
ENGLISH
Connecting to the Power
Supply
The washer should be plugged into a 120-VAC, 60
Hz grounded 3-prong outlet. Plug in the washer.
WARNING
Do not use a worn or damaged power cord or
power plug. Replace or repair it immediately.
Failure to do so may result in death, re, electric
shock, or malfunction.
Do not modify the power cord and plug provided
with the appliance. Take care not to damage it
when installing or moving the washer. Failure to
do so may result in death, re, electric shock, or
malfunction.
Make sure that the washer is grounded.
Connect this washer to a grounded outlet
conforming to the rating prior to use. Failure
to do so may result in re, electric shock, or
malfunction.
Do not damage or cut off the ground prong of
the power cord. Doing so may cause death, re,
electric shock, or product malfunction.
Improper connection of the equipment-grounding
conductor can result in risk of electric shock.
Check with a qualied electrician or service
technician if you are in doubt as to whether the
appliance is properly grounded. If it does not t
the outlet, have a proper outlet installed by a
qualied electrician
The appliance and outlet must be positioned so
that the plug is easily accessible.
Do not use adapters or extension cords. Doing
so may result in serious injury, re, electric
shock, or death.
For best performance, plug the washer into
its own individual outlet. This helps prevent
overloading house wiring circuits which could
cause a re hazard from overheated wires.
If necessary, use a new, UL-listed 3-prong
adapter or 3-wire extension cord with a 3-prong
(grounding) plug rated at no less than the branch
circuit. Do not use an extension cord longer
than 3 feet. Failure to follow these warnings may
result in serious injury, re, electric shock, or
death.
Testing the Washer
Check if the washer is properly installed and run a
test cycle.
1
Load the washer with 6 pounds of laundry
(approximately 6 thick bath towels).
2
Press the Power button.
3
Press the Rinse+Spin button.
4
Press the Start/Pause button.
The wash cycle starts.
5
Check if water is supplied, that the machine does
not rock or vibrate excessively, and that it drains
well during the spin cycle.
NOTE
If water leaks during water supply, see Connecting
the Water Lines to connect them properly.
If the washer rocks and vibrates excessively, see
Leveling the Washer to level it again.
If the drain does not work, see Connecting the Drain
Hose to install the hose properly.
16 OPERATION
OPERATION
Using the Washer
WARNING
To reduce the risk of re, electric shock, or injury to persons, read the SAFETY INSTRUCTIONS before
operating this appliance.
1
Sort Laundry and Load the Washer
Sort laundry by fabric type, soil level, color and load size, as needed. Open the
door and load items into the washer.
If using detergent pods, place pod in drum before loading laundry.
2
Add Cleaning Products.
Add the proper amount of HE (High-Efciency) detergent to the detergent
dispenser. If desired, add bleach or fabric softener to the appropriate areas of
the dispenser drawer. Do not place liquid or powdered detergent pods in the
dispenser.
3
Turn on the Washer
Press the Power button to turn on the washer. The lights above the cycle
buttons will illuminate and a chime will sound.
4
Select a Cycle
Turn the Cycle Selector Knob until the desired cycle is selected. The preset
Temp., Spin, Soil and option settings for that cycle will be shown. Pressing the
Start/Pause button without selecting a cycle will cause the Normal cycle to
begin immediately.
5
Adjust Settings
Default settings for the selected cycle can now be changed, if desired, using the
cycle modier and option buttons.
Not all modiers and options are available on all cycles. A different chime will
sound and the LED will not come on if the selection is not allowed.
6
Begin Cycle
Press the Start/Pause button to begin the cycle. The washer will agitate briey
without water to measure the weight of the load. If the Start/Pause button is not
pressed within 60 minutes, the washer will shut off and all settings will be lost.
7
End of Cycle
When the cycle is nished, a melody will sound. Immediately remove your
clothing from the washer to reduce wrinkling. Check around the door seal when
removing the load for small items that may be caught in the seal.
NOTE
The washer rotates the laundry in a way that allows it to use less water while still fully saturating your clothing.
It is normal to not be able to see water during the wash cycle.
If the temperature or the water level inside the machine is too high, the door will not unlock when the Start/
Pause button is pressed. To open the door in these circumstances, press Add Garments. To stop a cycle and
drain the water completely, turn the power off, then on, and then press Rinse+Spin.
17OPERATION
ENGLISH
Loading the Washer
Check and empty pockets. Paper clips, coins,
matches, etc. can damage clothing and the washer.
Close zippers and hooks, and tie drawstrings to
prevent snagging or tangling of clothes.
Pretreat heavily stained areas for best results.
Combine large and small items in a load. Load large
items rst. Large items should not be more than half
of total load.
The washer can be fully loaded, but the drum
should not be tightly packed with items. The door of
the washer must close easily.
Do not wash single small items. Add 1-2 similar
items to the load to prevent an out-of-balance load.
Wash thick, bulky items individually. Heavy blankets,
comforters, bedspreads, or pet beds can get
tangled or cause an unbalanced load if combined
with other items.
Do not wash/spin waterproof items. Washing
raincoats or sleeping bags may result in abnormal
vibration or may cause the load to bounce, which
could damage the drum.
Wash small, light items in a mesh bag. Items like
underwear can get caught in the door seal, and
a brassiere hook may damage other items or the
drum.
Brush off heavy soil, dust, and hair from items
before washing. Excess dirt or sand can abrade
other fabrics and lead to poor wash performance.
For best performance, load clothes as shown.
1
3
2
4
- Load clothes loosely, and do not overll the drum.
Clothes need room to circulate in order to get
clean.
- Do not press down on items while stacking them in
the drum.
This manual contains an abbreviated Operation
section. For the complete Operation section, scan
the QR code below or visit: https://us.smartthinq.
com/images/pdfmanual/VH_FL_VICTOR_799_
MFL68005567_EN.pdf
Sorting Laundry
Adding Cleaning Products
Control Panel
Wash Cycles
Cycle Guide
Cycle Modier Buttons
Option Buttons
18 SMART FUNCTIONS
SMART FUNCTIONS
LG SmartThinQ Application
The LG SmartThinQ application allows you to
communicate with the appliance using a smartphone.
Before Using LG SmartThinQ
For appliances with the or logo
1
Use a smartphone to check the strength of
the wireless router (Wi-Fi network) near the
appliance.
If the distance between the appliance and the
wireless router is too far, the signal strength
becomes weak. It may take a long time to
register or installation may fail.
2
Turn off the Mobile data or Cellular Data on your
smartphone.
3
Connect your smartphone to the wireless router.
NOTE
To verify the Wi-Fi connection, check that Wi-Fi
icon on the control panel is lit.
The appliance supports 2.4 GHz Wi-Fi networks
only. To check your network frequency, contact your
Internet service provider or refer to your wireless
router manual.
LG SmartThinQ is not responsible for any network
connection problems or any faults, malfunctions, or
errors caused by network connection.
The surrounding wireless environment can make
the wireless network service run slowly.
If the appliance is having trouble connecting to the
Wi-Fi network, it may be too far from the router.
Purchase a Wi-Fi repeater (range extender) to
improve the Wi-Fi signal strength.
The network connection may not work properly
depending on the Internet service provider.
The Wi-Fi connection may not connect or may
be interrupted because of the home network
environment.
If the appliance cannot be registered due to
problems with the wireless signal transmission,
unplug the appliance and wait about a minute
before trying again.
If the rewall on your wireless router is enabled,
disable the rewall or add an exception to it.
The wireless network name (SSID) should be a
combination of English letters and numbers. (Do not
use special characters.)
Smartphone user interface (UI) may vary depending
on the mobile operating system (OS) and the
manufacturer.
If the security protocol of the router is set to WEP,
network setup may fail. Change the security
protocol (WPA2 is recommended), and register the
product again.
Installing the LG SmartThinQ
Application
Search for the LG SmartThinQ application from the
Google Play Store or Apple App Store on a smart
phone. Follow instructions to download and install the
application.
19SMART FUNCTIONS
ENGLISH
LG SmartThinQ Application Features
For appliances with the or logo
Washer Cycle (Remote Start, Downloaded)
Set or download any preferred cycle and operate by
remote control.
Tub Clean Coach
This function shows how many cycles remain before
it is time to run the Tub Clean cycle.
Smart Diagnosis™
This function provides useful information for
diagnosing and solving issues with the appliance
based on the pattern of use.
Energy Monitoring
The washer energy usage is affected by the cycles
and options so you may see some changes in energy
usage from one cycle to another.
Push Alerts
When the cycle is complete or the appliance has
problems, you have the option of receiving push
notications on a smart phone.
Settings
Set the product nickname and delete product.
NOTE
If you change your wireless router, Internet service
provider, or password, delete the registered
appliance from the LG SmartThinQ application and
register it again.
This information is current at the time of publication.
The application is subject to change for product
improvement purposes without notice to users.
Using Washer Cycle
Remote Start
Use a smart phone to control the appliance remotely
or check to see how much time is left in the cycle.
Using Remote Start
1
Press the Power button.
2
Load the laundry.
3
Press and hold Remote Start button for 3
seconds to enable the Remote Start function.
4
Start a cycle from the LG SmartThinQ application
on your smart phone.
NOTE
Once the Remote Start mode is enabled, you can
start a cycle from the LG SmartThinQ smartphone
application. If the cycle is not started, the machine
will wait to start the cycle until it is turned off
remotely from the application or the Remote Start
mode is disabled.
When Remote Start is turned on, the door is
automatically locked.
Disabling Remote Start
When the Remote Start is activated, press and hold
the Remote Start button for 3 seconds.
Downloaded
Download new and specialized cycles that are not
included in the standard cycles on the appliance.
Appliances that have been successfully registered
can download a variety of specialty cycles specic to
the appliance.
Only one cycle can be stored on the appliance at a
time.
Once cycle download is completed in the appliance,
the appliance keeps the downloaded cycle until a
new cycle is downloaded.
20 SMART FUNCTIONS
Wireless LAN Module Specications
Model LCW-004
Frequency Range 2412 - 2462 MHz
Output Power
(Max)
IEEE 802.11 b : 22.44 dBm
IEEE 802.11 g : 24.68 dBm
IEEE 802.11 n : 24.11 dBm
FCC Notice (For transmitter module
contained in this product)
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct
the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
the receiver.
Connect the equipment to an outlet on a circuit
different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV
technician for help.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) This device may not cause harmful interference
and
2) This device must accept any interference received,
including interference that may cause undesired
operation of the device.
Any changes or modications in construction of this
device which are not expressly approved by the party
responsible for compliance could void the user’s
authority to operate the equipment.
FCC RF Radiation Exposure Statement
This equipment complies with FCC radiation
exposure limits set forth for an uncontrolled
environment. This transmitter must not be co-located
or operating in conjunction with any other antenna or
transmitter.
This equipment should be installed and operated with
a minimum distance of 20 cm (7.8 inches) between
the antenna and your body. Users must follow the
specic operating instructions for satisfying RF
exposure compliance.
Industry Canada Statement (For transmitter
module contained in this product)
This device complies with Industry Canada’s
applicable licence-exempt RSSs. Operation is subject
to the following two conditions:
1) This device may not cause interference; and
2) This device must accept any interference,
including interference that may cause undesired
operation of the device.
IC Radiation Exposure Statement
This equipment complies with IC radiation exposure
limits set forth for an uncontrolled environment.
This equipment should be installed and operated with
a minimum distance of 20 cm (7.8 inches) between
the antenna and your body.
NOTE
THE MANUFACTURER IS NOT RESPONSIBLE
FOR ANY RADIO OR TV INTERFERENCE
CAUSED BY UNAUTHORIZED MODIFICATIONS
TO THIS EQUIPMENT. SUCH MODIFICATIONS
COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT.
Open Source Software Notice
Information
To obtain the source code under GPL, LGPL, MPL,
and other open source licenses, that is contained in
this product, please visit http://opensource.lge.com.
In addition to the source code, all referred license
terms, warranty disclaimers and copyright notices are
available for download.
LG Electronics will also provide open source code
to you on CD-ROM for a charge covering the cost
of performing such distribution (such as the cost of
media, shipping, and handling) upon email request
to [email protected]. This offer is valid for a
period of three years after our last shipment of this
product. This offer is valid to anyone in receipt of this
information.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132

LG WM3505CW Le manuel du propriétaire

Catégorie
Machines à laver
Taper
Le manuel du propriétaire

dans d''autres langues