Whirlpool AKZM 831/IX Mode d'emploi

User and maintenance manual

Manuel d’utilisation et d’entretien

Руководство по эксплуатации

и техобслуживанию

Інструкція з експлуатації

і технічного обслуговування

UK

AKZM 831

GB1

YOUR SAFETY AND THAT OF OTHERS IS PARAMOUNT

This manual and the appliance itself provide important safety warnings, to be read and observed at all times.

All safety warnings give specific details of the potential risk present and indicate

how to reduce risk of injury, damage and electric shock resulting from improper

use of the appliance. Carefully observe the following instructions:

- The appliance must be disconnected from the power supply before carrying

out any installation work.

- Installation and maintenance must be carried out by a qualified technician,

in compliance with the manufacturer’s instructions and local safety

regulations. Do not repair or replace any part of the appliance unless

specifically stated in the user manual.

- Power cable replacement must be carried out by qualified electician.

Contact an authorizes service centre.

- Regulations require that the appliance is earthed.

- The power cable must be long enough for connecting the appliance, once

fitted in its housing, to the power supply socket.

- For installation to comply with current safety regulations, an all-pole

disconnect switch with minimum contact gap of 3 mm must be utilized.

- Do not use multiple plug adapters or extension leads.

- Do not pull the power supply cable in order to unplug the appliance.

- The electrical components must not be accessible to the user after

installation.

- Do not touch the appliance with any wet part of the body and do not

operate it when barefoot.

- This appliance is designed solely for use as a domestic appliance for cooking

food. No other type of use is permitted (e.g.: heating rooms). The

Manufacturer declines all responsibility for inappropriate use or incorrect

setting of the controls.

- This appliance can be used by children aged from 8 years and above and

persons with reduced physical, sensory or mental capabilities or lack of

experience and knowledge if they have been given supervision or

instruction concerning use of the appliance in a safe way and understand

hazards involved. Children shall not play with the appliance. Cleaning and

user maintenance shall not be made by children without supervision.

IMPORTANT SAFETY INSTRUCTIONS

This is the danger symbol, pertaining to safety, which alerts users to potential risks to themselves

and others.

All safety warnings are preceded by the danger symbol and the following terms:

DANGER

Indicates a hazardous situation which, if not avoided, will cause serious injury.

WARNING

Indicates a hazardous situation which, if not avoided, could cause serious injury.

GB2

- The accessible parts of the appliance may become very hot during use.

Young children should be kept away from the appliance and supervised to

ensure that they do not play with it.

- The appliance and its accessible parts become hot during use. Care should

be taken to avoid touching heating elements. Children less than 8 years old

shall be kept away, unless continuosly supervised.

- During and after use, do not touch the heating elements or interior surfaces

of the appliance - risk of burns. Do not allow the appliance to come into

contact with cloths or other flammable materials until all the components

have cooled sufficiently.

- At the end of cooking, exercise caution when opening the appliance door,

letting the hot air or steam exit gradually before accessing the oven. When

the appliance door is shut, hot air is vented from the aperture above the

control panel. Do not obstruct the vent apertures.

- Use oven gloves to remove pans and accessories, taking care not to touch

the heating elements.

- Do not place flammable materials in or near the appliance: a fire may break

out if the appliance is inadvertently switched on.

- Do not heat or cook sealed jars or containers in the appliance. The pressure

that builds up inside might cause the jar to explode, damaging the

appliance.

- Do not use containers made of synthetic materials.

- Overheated oils and fats catch fire easily. Always remain vigilant when

cooking foods rich in fat and oil.

- Never leave the appliance unattended during food drying.

- If alcoholic beverages are used when cooking foods (e.g. rum, cognac,

wine), remember that alcohol evaporates at high temperatures. As a result,

there is a risk that vapours released by the alcohol may catch fire upon

coming into contact with the electrical heating element.

- Never use steam cleaning equipment.

- Do not touch the oven during the pyrolysys cycle. Keep children away from

the oven during the pyrolysis cycle.(only for ovens with Pyrolisis function).

- Only use the temperature probe recommended for this oven.

- Do not use harsh abrasive cleaners or sharp metal scrapers to clean the

oven door glass since they can scratch the surface, which may result in

shattering of the glass.

- Ensure that the appliance is switched off before replacing the lamp to avoid

the possibility of electric shock.

GB3

Scrapping of household appliances

- This appliance is manufactured with recyclable or reusable materials. Dispose of it in accordance with

local waste disposal regulations. Before scrapping, cut off the power supply cable.

- For further information on the treatment, recovery and recycling of household electrical appliances,

contact your competent local authority, the collection service for household waste or the store where

you purchased the appliance.

After unpacking the oven, make sure that it has not been damaged during transport and that the oven

door closes properly. In the event of problems, contact the dealer or your nearest After-sales Service. To

prevent any damage, only remove the oven from its polystyrene foam base at the time of installation.

PREPARING THE HOUSING UNIT

• Kitchen units in contact with the oven must be heat resistant (min 90°C).

• Carry out all cabinet cutting work before fitting the oven in the housing and carefully remove all

wood chips and sawdust.

• Ensure the levelness of the oven support surface.

• After installation, the bottom of the oven must no longer be accessible.

• For correct appliance operation, do not obstruct the minimum gap between the worktop and the

upper edge of the oven.

ELECTRICAL CONNECTION

Make sure the power voltage specified on the appliance dataplate is the same as the mains voltage. The

dataplate is on the front edge of the oven (visible when the door is open).

• Power cable replacement (type H05 RR-F 3 x 1.5 mm

2

) must be carried out by a qualified electrician.

Contact an authorized service centre.

GENERAL RECOMMENDATIONS

Before use:

- Remove cardboard protection pieces, protective film and adhesive labels from accessories.

- Remove the accessories from the oven and heat it at 200° for about an hour to eliminate the smell

and fumes from the insulating materials and protective grease.

During use:

- Do not place heavy objects on the door as they could damage it.

- Do not cling to the door or hang anything from the handle.

- Do not cover the inside of the oven with aluminium foil.

- Never pour water into the inside of a hot oven; this could damage the enamel coating.

- Never drag pots or pans across the bottom of the oven as this could damage the enamel coating.

- Make sure that the electrical cables of other appliances do not touch hot parts of the oven or become

trapped in the door.

- Do not expose the oven to atmospheric agents.

Disposal of packing material

The packing material is 100% recyclable and is marked with the recycle symbol ( ). The various parts of

the packing must therefore be disposed of responsibly and in full compliance with local authority

regulations governing waste disposal.

Scrapping the product

- This appliance is marked in compliance with European Directive 2002/96/EC, Waste Electrical and

Electronic Equipment (WEEE).

- By ensuring this product is disposed of correctly, you will help prevent potential negative

consequences for the environment and human health, which could otherwise be caused by

inappropriate waste handling of this product.

INSTALLATION

SAFEGUARDING THE ENVIRONMENT

GB4

- The symbol on the product or on the accompanying documentation indicates that it should not be

treated as domestic waste but must be taken to an appropriate collection centre for the recycling of

electrical and electronic equipment.

Energy saving

- Only pre-heat the oven if specified in the cooking table or your recipe.

- Use dark lacquered or enamelled baking moulds as they absorb heat far better.

- This oven, which is intended to come into contact with foodstuffs, complies with European

Regulation ( ) n.1935/2004 and has been designed, manufactured and sold in conformity with the

safety requirements of the “Low Voltage” directive 2006/95/CE (which replaces 73/23/CEE and

subsequent amendments), the protection requirements of “EMC” 2004/108/CE.

The oven does not work:

• Check for the presence of mains electrical power and if the oven is connected to the electrical supply.

• Turn off the oven and restart it to see if the fault persists.

The door will not open:

• Turn off the oven and restart it to see if the fault persists.

The electronic programmer does not work:

• If the display shows the letter “ ” followed by a number, contact your nearest After-sales Service.

Specify in this case the number that follows the letter “ ”.

Before calling the After-Sales Service:

1. See if you can solve the problem yourself with the help of the suggestions given in the

“Troubleshooting guide“.

2. Switch the appliance off and back on again it to see if the fault persists.

If after the above checks the fault still occurs, get in touch with the nearest After-sales Service.

Always specify:

• a brief description of the fault;

• the type and exact model of the oven;

• the service number (number after the word Service on the rating plate), located on the right hand

edge of the oven cavity (visible when the oven door is open). The service number is also indicated on

the guarantee booklet;

• your full address;

• your telephone number.

If any repairs are required, please contact an authorised After-sales Service (to guarantee that original

spare parts will be used and repairs carried out correctly).

DECLARATION OF CONFORMITY

TROUBLESHOOTING GUIDE

AFTER-SALES SERVICE

GB5

Oven exterior

IMPORTANT: Do not use corrosive or abrasive detergents. If any of these products accidentally

comes into contact with the appliance, clean it immediately with a damp cloth.

• Clean the surfaces with a damp cloth. If very dirty, add a few drops of neutral detergent to the water.

Dry with a dry cloth.

Oven interior: STARCLEAN™ cleaning cycle

IMPORTANT: Do not use corrosive or abrasive detergents. Do not use abrasive sponges, metal

scrapers or scouring pads different from the sponge provided. Their use could eventually ruin the

enamelled surfaces. Only use non-abrasive sponges to clean the door glass.

The cavity of this oven is coated with a special formula enamel (nickel-free) enabling easily cleaning using

just water and the cellulose cloth provided. The cellulose cloth is washable and reusable until worn, and

can be purchased from the Customer Care Service. Washing the cloth in a washing-machine and drying it

in a dryer is inadvisable.

STARCLEAN™ cleaning cycle

To keep the oven in best condition, carry out the STARCLEAN™ cleaning cycle after each use. The cycle

takes 35 minutes, including a cooling stage, and must be carried out as follows:

1. Proceed with oven cold.

2. Wet the cellulose cloth provided under running water and wring it out so that it does not drip.

3. Open the oven door and remove the enamelled accessories.

4. Cover the bottom of the oven completely with the cellulose cloth.

5. Distribute 350 ml of water evenly on the cellulose cloth. A smaller or greater amount of water could

compromise proper functioning of the cycle.

6. Close the oven door.

7. Select the symbol with the functions knob: the word STARCLEAN™ appears on the display.

8. Press button to confirm the choice and start the cleaning cycle. To prevent steam coming out, do

not open the door during the cycle.

9. At the end of the cycle, remove the cellulose cloth and eliminate any residual water in the oven.

10. Then start cleaning using the sponge provided, moistened with hot water (cleaning could be

compromised if delayed by more than 15 minutes).

Particularly stubborn grime

To eliminate particularly stubborn grime, repeat the STARCLEAN™ cycle and add a few drops of neutral

detergent while removing the grime.

Cleaning inside glass

The inside surface of the door glass has a special coating that makes it easy to cleaning.

To keep the door glass in best condition, after every STARCLEAN™ cleaning cycle, clean the glass using just

water and a non-abrasive sponge.

Add a few drops of neutral detergent to the water to eliminate any greasy residuals.

NOTES:

• The oven door can be removed to facilitate cleaning (see MAINTENANCE).

• The top heating element of the grill (see MAINTENANCE) can be lowered to clean the roof of the

appliance.

• During prolonged cooking of foods containing lots of water (e.g. pizza, vegetables, etc.),

condensation may form inside the door and on the seal. Dry with a cloth or sponge when the

oven is cold.

CLEANING

WARNING

- Never use steam cleaners.

- Clean the appliance when it is cold.

- Disconnect the appliance from the power supply.

GB6

Accessories:

• Soak the accessories in water with washing up detergent after use, handling them with oven gloves if

still hot.

• Food residues can be removed using a suitable brush or sponge.

• Do not put the enamelled accessories in a dishwasher. The harsh detergents normally used in

dishwashers can permanently damage the enamel.

REMOVING THE DOOR

To remove the door:

1. Open the door fully.

2. Lift the catches and push them forwards as far as they will go (Fig. 1).

3. Close the door as far as it will go (A), lift it up (B) and turn it (C) until it is released (D) (Fig. 2).

To refit the door:

1. Insert the hinges in their seats.

2. Open the door fully.

3. Lower the two catches.

4. Close the door.

MOVING THE TOP HEATING ELEMENT (SOME MODELS ONLY)

1. Remove the side accessory holder grilles (Fig. 3).

2. Pull the heating element out a little (Fig. 4) and lower it (Fig. 5).

3. To reposition the heating element, lift it up, pulling it slightly towards you, making sure it comes to

rest on the lateral supports.

MAINTENANCE

WARNING

- Use protective gloves.

- Ensure the oven is cold before carrying out the following operations.

- Disconnect the appliance from the power supply.

Fig. 1 Fig. 2

Fig. 3 Fig. 4 Fig. 5

GB7

REPLACING THE OVEN LAMP

To replace the rear lamp (if present):

1. Disconnect the oven from the power supply.

2. Unscrew the lamp cover (Fig. 6), replace the lamp (see note for lamp type) and screw the lamp cover

back on.

3. Reconnect the oven to the power supply.

To replace the side lamp (if present):

1. Disconnect the oven from the power supply.

2. Remove the side accessory holder grilles, if present (Fig. 3).

3. Use a screwdriver to prise off the lamp cover (Fig. 7).

4. Replace the lamp (see note for lamp type) (Fig. 8).

5. Reposition the lamp cover, pushing it on firmly until it snaps into place (Fig. 9).

6. Refit the side accessory holder grilles.

7. Reconnect the oven to the power supply.

N.B.:

- Only use 25-40W/230V type E-14, T300°C incandescent lamps, or 20-40W/230 V type G9, T300°C

halogen lamps.

- The lamp used in the appliance is specifically designed for electrical appliances and is not suitable for

household room illumination (Commission Regulation (EC) No 244/2009).

- Lamps are available from our After-sales Service.

IMPORTANT:

- If using halogen lamps, do not handle with bare hands since fingerprints can damage them.

- Do not use the oven until the lamp cover has been repositioned.

Fig. 6 Fig. 7 Fig. 8 Fig. 9

GB8

FOR ELECTRICAL CONNECTION, SEE THE PARAGRAPH ON INSTALLATION

1. Control panel

2. Upper heating element/grill

3. Cooling fan (not visible)

4. Dataplate (not to be removed)

5. Light

6. Fan

7. Turnspit

8. Lower heating element (not visible)

9. Door

10. Position of shelves (the number of shelves is indicated on the front of the oven)

11. Rear wall

N.B.:

- During cooking, the cooling fan may switch on at intervals in order to minimise energy consumption.

- At the end of cooking, after the oven has been switched off, the cooling fan may continue to run for a

while.

ACCESSORIES SUPPLIED

A. WIRE SHELF (2): the wire shelf can be used to grill food or as a support for pans, cake tins and other

ovenproof cooking receptacles.

B. DRIP TRAY (1): the drip tray is designed to be positioned under the wire shelf in order to collect fat or

as an oven tray for cooking meat, fish, vegetables, focaccia, etc.

C. TURNSPIT (1): for uniform roasting of large pieces of meat and poultry.

D. CELLULOSE CLOTH (1): to be used for the STARCLEAN™ cleaning cycle.

IMPORTANT:Only use the cellulose cloth provided.

E. SPONGE: to be used for removing grime in the cavity

ACCESSORIES NOT SUPPLIED

Other accessories can be purchased separately from the After-sales Service.

INSTRUCTIONS FOR OVEN USE

Fig. A Fig. B Fig. C Fig. D Fig. E

GB9

INSERTING WIRE SHELVES AND OTHER ACCESSORIES IN THE OVEN

The wire shelf and other accessories are provided with a locking mechanism to prevent their unintentional

removal.

1. Insert the wire shelf horizontally, with the raised part “A” upwards (Fig. 1).

2. Angle the wire shelf when it reaches the locking position “B” (Fig. 2).

3. Return the wire shelf to the horizontal position and push it in fully to “C” (Fig. 3).

4. To remove the wire shelf proceed in reverse order.

The other accessories, like the drip tray and baking tray, are inserted in exactly the same way. The

protrusion on the flat surface enables the accessories to lock in place.

CONTROL PANEL DESCRIPTION

ELECTRONIC PROGRAMMER

1. FUNCTION SELECTOR KNOB: On/off and function selector knob

2. BROWSE KNOB: for browsing the menu and adjusting pre-set values

3. BUTTON : to return to the previous screen

4. BUTTON : to select and confirm settings

LIST OF FUNCTIONS

Turn the “Functions” knob to any position and the oven switches on: the display shows the functions or the

associated submenus.

The submenus are available and selectable by turning the knob to the functions GRILL, SPECIALS,

SETTINGS, BREAD/PIZZA.

N.B.:for the list and description of functions, see the specific table at page15.

Fig. 1

Fig. 2 Fig. 3

GB10

DESCRIPTION OF DISPLAY

A. Display of heating elements activated during the various cooking functions

B. Time management symbols: timer, cooking time, end of cooking time, time

C. Information regarding selected functions

D. Automatic BREAD/PIZZA function selected

E. Indication of door locked during automatic cleaning cycle (if present)

F. Internal oven temperature

G. Pyrolisis function (if present)

H. Browning

I. Special functions: Defrost, Keep Warm, Rising

STARTING THE OVEN - SETTING THE TIME

After connecting the oven to the mains power, the time must be set on the clock. The two hour digits flash

on the display.

1. Turn the “Browse” knob to display the correct hour.

2. Press the button to confirm; the two minute digits flash on the display.

3. Turn the “Browse” knob to display the correct minutes.

4. Press button to confirm.

To change the time, for example following a power cut, see the next paragraph (SETTINGS).

SELECTING COOKING FUNCTIONS

1. Turn the “Functions” knob to the desired function: the cooking settings are shown on the display.

2. If the values shown are those desired, press . To change them, proceed as indicated below.

SETTING THE TEMPERATURE/OUTPUT OF THE GRILL

To change the temperature or output of the grill, proceed as follows:

1. Turn the “Browse” knob to display the desired value.

2. Press button to confirm.

The oven automatically confirms your selection 10 seconds after the last operation.

A

B C D

E

I H G F

GB11

FAST PREHEATING

1. Turn the “Functions” knob to the symbol to select the fast preheating function.

2. Confirm by pressing : the settings are shown on the display.

3. If the proposed temperature is that desired, press button . To change the temperature, proceed as

described in previous paragraphs. The message PRE appears on the display. When the set

temperature is reached, the corresponding value (e.g. 200°C) appears on the display and the acoustic

signal sounds. At the end of preheating, the oven automatically selects the conventional function .

At this point food can be placed in the oven for cooking.

4. If you wish to set a different cooking function, turn the “Functions” knob and select the desired

function.

SETTING COOKING TIME

This function can be used to cook food for a set length of time, from a minimum of 1 minute to the

maximum time allowed by the selected function, after which the oven switches off automatically.

1. Once the temperature is confirmed, the symbol flashes.

2. Turn the adjustment knob to display the desired cooking time.

3. To confirm the cooking time, press button .

The oven automatically confirms your selection 10 seconds after the last operation.

SETTING END OF COOKING TIME/START DELAYED

IMPORTANT:the start delayed setting is not available for the following functions: FAST

PREHEATING, BREAD/PIZZA, GENTLE CONVECTION BAKE.

N.B.:with this setting, the selected temperature is reached in a more gradual way, so cooking times

will be slightly longer than stated in the cooking table.

The end of cooking time can be set, delaying the start of cooking by up to a maximum of 23 hours and

59 minutes. This can only be done once cooking time has been set.

After setting cooking time, the display shows the end of cooking time (for example 15:45) and the

symbol flashes.

To delay the end of cooking time, and thus also the cooking start time, proceed as follows:

1. Turn the “Browse” knob to display the time you wish cooking to end (for example 16:00).

2. Confirm the selected value by pressing button : the two dots of end of cooking time flash,

indicating that the setting has been made correctly.

3. The oven will automatically delay the start of cooking so as to finish cooking at the set time.

At any time, however, set values (temperature, grill setting, cooking time) can be changed using

button to go back, followed by the “Browse” knob to change values and button to confirm.

INDICATION OF THE RESIDUAL HEAT INSIDE THE OVEN (IF PRESENT)

If at the end of cooking, or when the oven is switched off, the temperature inside the oven is high, the

display on some models shows the message HOT together with the current temperature. Once the oven

chamber has cooled down, the display shows the current time again.

GB12

TIMER

This function can be used only with the oven switched off and is useful, for example, for monitoring the

cooking time of pasta. The maximum time which can be set is 23 hours and 59 minutes.

1. With the “Functions” knob at zero, turn the “Browse” knob to display the desired time.

2. Press button to start the countdown. When the set time has elapsed, the display will show “0:00”

and an acoustic signal will sound. To mute the acoustic signal, press button (the time of day

appears on the display).

SELECTING SPECIAL FUNCTIONS

Turn the “Functions” knob indicator to the symbol to access a submenu containing three special

functions.

To browse, select and start one of these functions, proceed as follows:

1. Turn the “Functions” knob to symbol : the display shows “ DEFROST” along with this function’s

corresponding symbol.

2. Turn the “Browse” knob to scroll the list of functions; the function names are in English: DEFROST,

KEEP WARM, RISING.

3. Press button to confirm.

BROWNING

At the end of cooking, with certain functions, the display indicates the possibility of browning. This

function can only be used when cooking time has been set.

At the end of cooking time, the display shows: “PRESS TO BROWN”. Press button , and the oven starts

a 5 minute browning cycle. This function can be selected consecutively a maximum of twice.

BREAD/PIZZA FUNCTION SELECTION

Turn the “Functions” knob indicator to the symbol to access a submenu containing two automatic

cooking functions for “bread” and “pizza”.

Bread

1. Turn the “Functions” knob to symbol : the display shows “BREAD” and AUTO at the side.

2. Press to select the function.

3. Turn the “Browse” knob to set the required temperature (between 180°C and 220°C) and confirm with

button .

4. Turn the “Browse” knob to set the required cooking duration and press to start cooking.

GB13

Pizza

1. Turn the Functions knob to symbol : the display shows “BREAD”. To select the “PIZZA” function,

proceed as follows:

2. Turn the “Browse” knob: “PIZZA” appears on the display.

3. Press to select the function.

4. Turn the “Browse” knob to set the required temperature (between 220°C and 250°C) and confirm with

button .

5. Turn the “Browse” knob to set the required cooking duration and press to start cooking.

SETTINGS

Turn the “Functions” knob indicator to the symbol to access a submenu containing four display

settings which can be changed.

Clock

Turn the “Functions” knob to the symbol : the word CLOCK appears on the display. To change the time

of day, see the previous paragraph (SETTING THE TIME).

Eco

With the ECO mode selected (ON), the display switches off when the oven is on standby or 5 minutes after

the end of cooking. To view information on the display, simply press a button or turn a knob.

1. Turn the “Browse” knob to display “ECO.

2. Press to access the setting (ON/OFF).

3. Turn the “Browse” knob to select the desired setting and confirm by pressing button .

Acoustic signal

To activate or deactivate the acoustic signal, proceed as follows:

1. Turn the “Browse” knob to display “SOUND.

2. Press to access the setting (ON/OFF).

3. Turn the “Browse” knob to select the desired setting and confirm by pressing button .

N.B.:when set to off, the following signals remain nonetheless active: timer end, preheating end,

cooking end.

Brightness

To change the display brightness, proceed as follows:

1. Turn the “Browse” knob to display “BRIGHTNESS.

2. Press button : the display shows LOW, MID or HIGH depending on the level currently set.

3. Turn the “Browse” knob to increase or decrease brightness and confirm by pressing .

GB14

STARCLEAN™ CLEANING CYCLE

To keep the oven in best condition, carry out the STARCLEAN™ cleaning cycle after each use. The cycle

takes 35 minutes, including a cooling stage, and must be carried out as follows:

For the description of this function, see the section CLEANING and the functions table on page15.

1. Proceed with oven cold.

2. Wet the cellulose cloth provided under running water and wring it out so that it does not drip.

3. Open the oven door and remove the enamelled accessories.

4. Cover the bottom of the oven completely with the cellulose cloth.

5. Distribute 350 ml of water evenly on the cellulose cloth. A smaller or greater amount of water could

compromise proper functioning of the cycle.

6. Close the oven door.

IMPORTANT:To prevent steam coming out, do not open the door during the cycle.

7. Select the symbol with the functions knob: the word STARCLEAN™ appears on the display.

8. Press button to confirm the choice and start the cleaning cycle. To prevent steam coming out, do

not open the door during the cycle.

9. At the end of the cycle, remove the cellulose cloth and eliminate any residual water in the oven.

10. Then start cleaning using the sponge provided, moistened with hot water (cleaning could be

compromised if delayed by more than 15 minutes).

Particularly stubborn grime

To eliminate particularly stubborn grime, repeat the STARCLEAN™ cycle and add a few drops of neutral

detergent while removing the grime.

KEY-LOCK

This function can be used to lock the buttons and knobs on the control panel.

To activate it, press and at the same time for at least 3 seconds. When activated, the functions

associated with the buttons are locked and the display shows a key symbol. This function can also be

activated during cooking. To deactivate it, repeat the above procedure. When the key-lock function is

activated, the oven can be switched off by turning the knob to 0 (zero). In this case, however, the previously

selected function will have to be set again.

GB15

FUNCTION DESCRIPTION TABLE

FUNCTIONS KNOB

OFF To stop cooking and switch off the oven.

LAMP To switch the oven interior light on/off.

SPECIALS

DEFROST

To speed up defrosting of food. Place food on the middle shelf. Leave food in

its packaging in order to prevent it from drying out on the outside.

KEEP WARM

For keeping just-cooked food hot and crisp (e.g: meat, fried food or flans).

Place food on the middle shelf. The function will not activate if the

temperature in the oven is above 65°C.

RISING

For optimal rising of sweet or savoury dough. To safeguard the quality of

proving, the function will not activate if the temperature in the oven is above

40°C. Place the dough on the 2nd shelf. The oven does not have to be

preheated.

CONVENTIONAL

To cook any kind of dish on one shelf only. Use the 3rd shelf. To cook pizza,

savoury pies and sweets with liquid fillings, use the 1st or 2nd shelf. Preheat

the oven before placing food inside.

CONVECTION

BAKE

For baking cakes with liquid filling (sweet or savoury) on a single shelf. This

function can also be used for cooking on two shelves. Switch the position of

the dishes to cook food more evenly. Use the 3rd shelf to cook on one shelf

only, and the 1st and 4th to cook on two shelves. Preheat the oven before

cooking.

GENTLE

CONVECTION

BAKE -

GENTLE FAN

For cooking meat, filled pies (cheesecake, strudel, fruit pies) and stuffed

vegetables on one level only. This function uses discontinuous, delicate fan

assistance, which prevents excessive drying of foods. It is advisable to use

2nd level. Preheat the oven before cooking.

GRILL

To grill steak, kebabs and sausages; to cook vegetables au gratin and toast

bread. Place food on the 4th or 5th shelf. When grilling meat, use the drip

tray to collect the cooking juices. Position it on the 3rd/4th shelf, adding

approx. half a litre of water. The oven does not have to be preheated. During

cooking the oven door must remain closed.

TURBO GRILL

To roast large joints of meat (legs, roast beef, chickens). Position the food on

the middle shelves. Use the drip tray to collect the cooking juices. Position it

on the 1st/2nd shelf, adding approx. half a litre of water. The oven does not

have to be preheated. During cooking the oven door must remain closed.

With this function you can also use the turnspit, if provided.

MAXI COOKING

To cook large joints of meat (above 2.5 kg). Use the 1st or 2nd shelf,

depending on the size of the joint. The oven does not have to be preheated.

It is advisable to turn the meat over during cooking for more even browning.

It is best to baste the meat every now and again to avoid it drying out.

SETTINGS

To set the display (language, time, brightness, buzzer volume, energy

saving).

GB16

BREAD/PIZZA

To bake different types and sizes of pizza and bread. This function contains

two programmes with predefined settings. Simply indicate the values

required (temperature and time) and the oven will manage the cooking

cycle automatically. Place the dough on the 2nd shelf after preheating the

oven.

STARCLEAN™

To eliminate the dirt created by cooking by means of a low temperature

cycle. The combined action of the special enamel and the water released by

the cellulose cloth during the cycle facilitates removal of grime. Activate the

function when the oven is cold.

FAST PREHEATING To preheat the oven rapidly.

FUNCTIONS KNOB (Continued)

GB17

COOKING TABLE

Recipe Function Pre-

heating

Shelf (from

bottom)

Temp.

(°C)

Time

(min)

Accessories and notes

Leavened cakes

Yes 2/3 160-180 30-90 Cake tin on wire shelf

Yes 1-4 160-180 30-90

Shelf 4: cake tin on wire shelf

(switch levels halfway

through cooking)

Shelf 1: cake tin on wire shelf

Filled pies (cheese-

cake, strudel, fruit

pie)

GENTLE

Yes 2 160-200 35-90

Drip tray/baking tray or cake

tin on wire shelf

Yes 1-4 160-200 35-90

Shelf 4: cake tin on wire shelf

(switch levels halfway

through cooking)

Shelf 1: cake tin on wire shelf

Biscuits / Tartlets

Yes 3 170-180 15-45 Drip tray / baking tray

Yes 1-4 160-170 20-45

Shelf 4: oven tray on wire

shelf (switch levels halfway

through cooking)

Shelf 1: drip tray / baking tray

Choux buns

Yes 3 180-200 30-40 Drip tray / baking tray

Yes 1-4 180-190 35-45

Shelf 4: oven tray on wire

shelf (switch levels halfway

through cooking)

Shelf 1: drip tray / baking tray

Meringues

Yes 3 90 110-150 Drip tray / baking tray

Yes 1-4 90 130-150

Shelf 4: oven tray on wire

shelf (switch levels halfway

through cooking)

Shelf 1: drip tray / baking tray

Bread / Pizza /

Focaccia

Yes 1/2 190-250 15-50 Drip tray / baking tray

Yes 1-4 190-250 25-50

Shelf 4: oven tray on wire

shelf (switch levels halfway

through cooking)

Shelf 1: drip tray / baking tray

Bread

(Bread)

Yes 2 180-220 30-50

Drip tray / baking tray or wire

shelf

Pizza

(Pizza)

Yes 2 220-250 15-30 Drip tray / baking tray

Frozen pizza

Yes 3 250 10-15

Shelf 3: drip tray / baking tray

or wire shelf

Yes 1-4 250 10-20

Shelf 4: oven tray on wire

shelf (switch levels halfway

through cooking)

Shelf 1: drip tray / baking tray

GB18

Savoury pies (veg-

etable pie, quiche)

Yes 3 180-190 40-55 Cake tin on wire shelf

Yes 1-4 180-190 40-55

Shelf 4: cake tin on wire shelf

(switch levels halfway

through cooking)

Shelf 1: cake tin on wire shelf

Vols-au-vent / Puff

pastry crackers

Yes 3 190-200 20-30 Drip tray / baking tray

Yes 1-4 180-190 15-40

Shelf 4: oven tray on wire

shelf (switch levels halfway

through cooking)

Shelf 1: drip tray / baking tray

Lasagne / Baked

pasta / Cannelloni /

Flans

Yes 3 190-200 45-55 Oven tray on wire shelf

Lamb / Veal / Beef /

Pork 1 Kg

GENTLE

Yes 2 180-190 80-120

Drip tray or oven tray on wire

shelf

Chicken / Rabbit /

Duck 1 Kg

GENTLE

Yes 3 200-220 50-100

Drip tray or oven tray on wire

shelf

Turkey / Goose

3Kg

Yes 2 190-200 80-130

Drip tray or oven tray on wire

shelf

Baked fish / en

papillote (fillet,

whole)

Yes 3 180-200 40-60

Drip tray or oven tray on wire

shelf

Stuffed vegetables

(tomatoes, cour-

gettes, aubergines)

Yes 2 170-190 30-60 Oven tray on wire shelf

Toast - 5 3 (High) 3-6 Wire shelf

Fish fillets / steaks - 4 2 (Medium) 20-30

Shelf 4: wire shelf (turn food

halfway through cooking)

Shelf 3: drip tray with water

Sausages / Kebabs

/ Spare ribs / Ham-

burgers

- 5

2-3

(Medium-

High)

15-30

Shelf 5: wire shelf (turn food

halfway through cooking)

Shelf 4: drip tray with water

Roast chicken 1-1.3

Kg

- 2

2 (Medium) 55-70

Shelf 2: wire shelf (turn food

two thirds of the way

through cooking if

necessary)

Level 1: drip-tray with water

3 (High) 80-110

Level 2: turnspit (if present)

Level 1: drip-tray with water

Roast Beef rare

1Kg

- 3 2 (Medium) 35-45

Oven tray on wire shelf (turn

food two thirds of the way

through cooking if

necessary)

Leg of lamb /

Shanks

- 3 2 (Medium) 60-90

Drip tray or oven tray on wire

shelf (turn food two thirds of

the way through cooking if

necessary)

Recipe Function Pre-

heating

Shelf (from

bottom)

Temp.

(°C)

Time

(min)

Accessories and notes

La page charge ...

Whirlpool AKZM 831/IX Mode d'emploi

Whirlpool AKZM 831/IX Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents