Hitachi G23MR - 9" Disc Grinder Manuel utilisateur

Marque: Hitachi

Modèle: G23MR - 9" Disc Grinder

Catégorie: Meuleuses d'angle

Taper: Manuel utilisateur

Ce manuel convient également à

G 18MR • G 23MR

Model Disc Grinder

Modèle Meuleuse

Modelo Amoladora angular

INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI

AVERTISSEMENT

Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner la

mort ou de sérieuses blessures corporelles !

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce

produit. Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil

motorisé. Garder ce mode d’emploi à la disponibilité des autres utilisateurs et

propriétaires avant qu’ils utilisent l’outil motorisé.

Ce mode d’emploi doit être conservé dans un endroit sûr.

INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES

ADVERTENCIA

¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede resultar

en lesiones de gravedad o la muerte!

Este manual contiene información importante sobre la seguridad del producto. Lea y

comprenda este manual ANTES de utilizar la herramienta eléctrica. Guarde este manual

para que puedan leerlo otras personas antes de utilizar la herramienta eléctrica.

Este manual debe ser guardado en un lugar seguro.

DOUBLE INSULATION

DOUBLE ISOLATION

AISLAMIENTO DOBLE

SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL

WARNING

IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily

injury!

This manual contains important information about product safety. Please read and

understand this manual BEFORE operating the power tool. Please keep this manual

available for other users and owners before they use the power tool.

This manual should be stored in safe place.

G23MR

IMPORTANT SAFETY INFORMATION ...... 3

MEANINGS OF SIGNAL WORDS .............. 3

SAFETY ............................................................ 4

GENERAL SAFETY RULES ......................... 4

SPECIFIC SAFETY RULES AND

SYMBOLS.............................................. 6

DOUBLE INSULATION FOR SAFER

OPERATION .......................................... 8

FUNCTIONAL DESCRIPTION ....................... 10

NAME OF PARTS ...................................... 10

SPECIFICATIONS ...................................... 10

ASSEMBLY AND OPERATION ..................... 11

APPLICATIONS ......................................... 11

PRIOR TO OPERATION ............................. 11

GRINDER OPERATION ............................. 13

DEPRESSED CENTER WHEEL

ASSEMBLY AND DISASSEMBLY ...... 14

MAINTENANCE AND INSPECTION ............. 15

ACCESSORIES .............................................. 17

STANDARD ACCESSORIES ..................... 17

OPTIONAL ACCESSORIES ....................... 17

PARTS LIST ................................................... 50

CONTENTS

English

Page Page

ÍNDICE

Español

Página Página

INFORMACIÓN IMPORTANTE SOBRE

SEGURIDAD ........................................ 33

SIGNIFICADO DE LAS PALABRAS DE

SEÑALIZACIÓN................................... 33

SEGURIDAD .................................................. 34

NORMAS GENERALES DE SEGURIDAD 34

NORMAS Y SÍMBOLOS ESPECÍFICOS DE

SEGURIDAD ........................................ 36

AISLAMIENTO DOBLE PARA OFRECER

UNA OPERACIÓN MÁS SEGURA ..... 39

DESCRIPCIÓN FUNCIONAL ......................... 40

NOMENCLATURA ..................................... 40

ESPECIFICACIONES .................................. 40

MONTAJE Y OPERACIÓN ............................ 41

APLICACIONES ......................................... 41

ANTES DE LA OPERACIÓN ...................... 41

OPERACIÓN DE LA AMOLADORA

ANGULAR ........................................... 43

MONTAJE Y DESMONTAJE DE LA

RUEDA DE DISCO ABOMBADO ........ 44

MANTENIMIENTO E INSPECCIÓN .............. 46

ACCESORIOS ................................................ 48

ACCESORIOS ESTÁNDAR ....................... 48

ACCESORIOS OPCIONALES .................... 48

LISTA DE PEIZAS .......................................... 50

TABLE DES MATIERES

Français

Page Page

INFORMATIONS IMPORTANTES DE

SÉCURITÉ ............................................ 18

SIGNIFICATION DES MOTS

D’AVERTISSEMENT ........................... 18

SECURITE ...................................................... 19

REGLES GENERALE DE SECURITE ......... 19

REGLES DE SECURITE SPECIFIQUES

ET SYMBOLES .................................... 21

DOUBLE ISOLATION POUR UN

FONCTIONNEMENT PLUS SUR ........ 24

DESCRIPTION FONCTIONNELLE ................ 25

NOM DES PARTIES .................................. 25

SPECIFICATIONS ...................................... 25

ASSEMBLAGE ET FONCTIONNEMENT ...... 26

UTILISATIONS .......................................... 26

AVANT L’UTILISATION ............................ 26

UTILISATION DE LA MEULEUSE ............ 28

ASSEMBLAGE ET DESASSEMBLAGE

DE LA MEULE A DEPRESSION

CENTRALE .......................................... 29

ENTRETIEN ET INSPECTION ....................... 30

ACCESSOIRES .............................................. 32

ACCESSOIRES STANDARD ..................... 32

ACCESSOIRES SUR OPTION ................... 32

LISTE DES PIECES ........................................ 50

English

IMPORTANT SAFETY INFORMATION

Read and understand all of the safety precautions, warnings and operating instructions in

the Instruction Manual before operating or maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused by the

failure to observe basic safety rules or precautions. An accident can often be avoided by

recognizing a potentially hazardous situation before it occurs, and by observing appropriate

safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual

and in the sections which contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identified by

WARNINGS on the power tool and in this Instruction Manual.

NEVER use this power tool in a manner that has not been specifically recommended by

HITACHI.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could result in

death or serious injury.

CAUTION indicates a potentially hazardous situations which, if not avoided, may result in

minor or moderate injury, or may cause machine damage.

NOTE emphasizes essential information.

English

SAFETY

GENERAL SAFETY RULES

WARNING: Read and understand all instructions.

Failure to follow all instructions listed below, may result in electric shock,

fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

1. Work Area

(1) Keep your work area clean and well lit. Cluttered benches and dark areas invite

accidents.

(2) Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases, or dust. Power tools create sparks which may ignite the

dust of fumes.

(3) Keep bystanders, children, and visitors away while operating a power tool.

Distractions can cause you to lose control.

2. Electrical Safety

(1) Double Insulated tools are equipped with a polarized plug (one blade is wider than

the other). This plug will fit in a polarized outlet only one way. If the plug does not

fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified

electrician to install a polarized outlet. Do not change the plug in any way. Double

Insulation

eliminates the need for the three wire grounded power cord and

grounded power supply system.

(2) Avoid body contact with grounded surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is grounded.

(3) Don’t expose power tools to rain or wet conditions. Water entering a power tool

will increase the risk of electric shock.

(4) Do not abuse the cord. Never use the cord to carry the tools or pull the plug from

an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace

damaged cords immediately. Damaged cords increase the risk of electric shock.

(5) When operating a power tool outside, use an outdoor extension cord marked “W-

A” or “W”. These cords are rated for outdoor use and reduce the risk of electric

shock.

3. Personal Safety

(1) Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use tool while tired or under the influence of drugs, alcohol, or

medication. A moment of inattention while operating power tools may result in

serious personal injury.

(2) Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep

your hair, clothing and gloves away from moving parts. Loose clothes, jewelry, or

long hair can be caught in moving parts.

English

(3) Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools

with your finger on the switch or plugging in tools that have the switch on invites

accidents.

(4) Remove adjusting keys or wrenches before turning the tool on. A wrench or a key

that is left attached to a rotating part of the tool may result in personal injury.

(5) Do not overreach. Keep proper footing and balance at all times. Proper footing and

balance enables better control of the tool in unexpected situations.

(6) Use safety equipment. Always wear eye protection. Dust mask, non-skid safety

shoes, hard hat, or hearing protection must be used for appropriate conditions.

4. Tool Use and Care

(1) Use clamps or other practical way to secure and support the workpiece to a stable

platform. Holding the work by hand or against your body is unstable and may lead

to loss of control.

(2) Do not force tool. Use the correct tool for your application. The correct tool will do

the job better and safer at the rate for which it is designed.

(3) Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled

with the switch is dangerous and must be repaired.

(4) Disconnect the plug form the power source before making any adjustments,

changing accessories, or storing the tool. Such preventive safety measures reduce

the risk of starting the tool accidentally.

(5) Store idle tools out of reach of children and other untrained persons. Tools are

dangerous in the hands of untrained users.

(6) Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained

tools, with sharp cutting edges are less likely to bind and are easier to control.

(7) Check for misalignment or binding of moving parts, breakage of parts, and any

other condition that may affect the tool's operation. If damaged, have the tool

serviced before using. Many accidents are caused by poorly maintained tools.

(8) Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool, may become hazardous when used

with another tool.

5. Service

(1) Tool service must be performed only by qualified repair personnel. Service or

maintenance performed by unqualified personnel could result in a risk of injury.

(2) When servicing a tool, use only identical replacement parts. Follow instructions in

the Maintenance section of this manual. Use of unauthorized parts or failure to

follow Maintenance Instruction may create a risk of electric shock or injury.

English

SPECIFIC SAFETY RULES AND SYMBOLS

1. ALWAYS use proper guard with grinding wheel. A guard protects operator from broken

wheel fragments.

2. Accessories must be rated for at least the speed recommended on the tool warning

label. Wheels and other accessories running over rated speed can fly apart and cause

injury.

3. Hold tools by insulated gripping surfaces when performing an operation where the

cutting tool may contact hidden wiring or its own cord. Contact with a “live” wire will

make exposed metal parts of the tool “live” and shock the operator.

4. ALWAYS wear ear protectors when using the tool for extended periods.

Prolonged exposure to high intensity noise can cause hearing loss.

5. Use only a depressed center wheel with a rated capacity which is GREATER than 6600

RPM. Using any wheel a rated capacity LESS than 6600 RPM and/or an incorrect sized

wheel (see SPECIFICATIONS at page 10) may result in wheel breakage, flying wheel

fragments, and resulting in death or serious injury.

6. NEVER touch moving parts.

NEVER place your hands, fingers or other body parts near the tool’s

moving parts.

7. NEVER operate without all guards in place.

NEVER operate this tool without all guards or safety features in place and in proper

working order. If maintenance or servicing requires the removal of a guard or safety

feature, be sure to replace the guard or safety feature before resuming operation of the

tool.

8. Use right tool.

Don’t force small tool or attachment to do the job of a heavy-duty tool.

Don’t use tool for purpose not intended —for example— don’t use circular saw for

cutting tree limbs or logs.

9. NEVER use a power tool for applications other than those specified.

NEVER use a power tool for applications other than those specified in the Instruction

Manual.

English

10. Handle tool correctly.

Operate the tool according to the instructions provided herein. Do not drop or throw

the tool. NEVER allow the tool to be operated by children, individuals unfamiliar with

its operation or unauthorized personnel.

11. Keep all screws, bolts and covers tightly in place.

Keep all screws, bolts, and plates tightly mounted. Check their condition periodically.

12. Do not use power tools if the plastic housing or handle is cracked.

Cracks in the tool’s housing or handle can lead to electric shock. Such tools should not

be used until repaired.

13. Blades and accessories must be securely mounted to the tool.

Prevent potential injuries to youself or others. Blades, cutting implements and

accessories which have been mounted to the tool should be secure and tight.

14. Keep motor air vent clean.

The tool’s motor air vent must be kept clean so that air can freely flow at all times.

Check for dust build-up frequently.

15. Operate power tools at the rated voltage.

Operate the power tool at voltages specified on its nameplate.

If using the power tool at a higher voltage than the rated voltage, it will result in

abnormally fast motor revolution and may damage the unit and the motor may burn

out.

16. NEVER use a tool which is defective or operating abnormally.

If the tool appears to be operating unusually, making strange noises, or otherwise

appears defective, stop using it immediately and arrange for repairs by a Hitachi

authorized service center.

17. NEVER leave tool running unattended. Turn power off.

Don’t leave tool until it comes to a complete stop.

18. Carefully handle power tools.

Should a power tool be dropped or struck against hard materials inadvertently, it may

be deformed, cracked, or damaged.

19. Do not wipe plastic parts with solvent.

Solvents such as gasoline, thinner benzine, carbon tetrachloride, and alcohol may

damage and crack plastic parts. Do not wipe them with such solvents.

Wipe plastic parts with a soft cloth lightly dampened with soapy water and dry

thoroughly.

20. NEVER use a depressed center wheel which is cracked or deformed or worn away (see

the MAINTENANCE AND INSPECTION section on page 15).

21. NEVER use the grinder in places where the sparks generated by the grinder can cause

explosion, such as where flammable materials or gases are present.

22. NEVER push in the push button while the spindle is running.

23. ALWAYS wear eye protection that meets the requirement of the latest revision of ANSI

Standard Z87.1.

English

24. ALWAYS wear a mask or respirator to protect yourself from dust or potentially harmful

particles generated during the grinding operation.

25. ALWAYS firmly grip the body handle and side handle while operating the grinder.

26. ALWAYS have a trial run before grinding commence (see “Test the grinder before

using” on page 12).

27. ALWAYS follow the instructions contained in this manual when replacing the depressed

center wheel.

28. ALWAYS be careful with buried object such as an underground wiring.

Touching these active wiring or electric cable with this tool, you may receive an electric

shock.

Comfirm if there are any buried object such as electric cable within the wall, floor or

ceiling where you are going to operate here after.

29. Definitions for symbols used on this tool

V ............ volts

Hz .......... hertz

A ............ amperes

no .......... no load speed

W ........... watt

........... Class II Construction

---/min ... revolutions per minute

DOUBLE INSULATION FOR SAFER OPERATION

To ensure safer operation of this power tool, HITACHI has adopted a double insulation

design. “Double insulation “ means that two physically separated insulation systems have

been used to insulate the electrically conductive materials connected to the power supply

from the outer frame handled by the operator. Either the symbol “

” or the words “Double

insulation” appear on the power tool or on the nameplate.

Although this system has no external grounding, you must still follow the normal electrical

safety precautions given in this Instruction Manual, including not using the power tool in

wet environments.

To keep the double insulation system effective, follow these precautions:

䡬 Only HITACHI AUTHORIZED SERVICE CENTER should disassemble or assemble this

power tool, and only genuine HITACHI replacement parts should be installed.

䡬 Clean the exterior of the power tool only with a soft cloth moistened with soapy water,

and dry thoroughly.

Never use solvents, gasoline or thinners on plastic components; otherwise the plastic

may dissolve.

English

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO

OTHER USERS AND OWNERS

OF THIS TOOL!

English

Push Button

Gear Cover

Packing Gland

Switch

Housing

Fig. 1

Side Handle

Wheel Guard

Depressed Center Wheel

Handle

Brush Cover

FUNCTIONAL DESCRIPTION

NOTE: The information contained in this Instruction Manual is designed to assist you in

the safe operation and maintenance of the power tool.

NEVER operate, or attempt any maintenance on the tool unless you have first read

and understood all safety instructions contained in this manual.

Some illustrations in this Instruction Manual may show details or attachments that

differ from those on your own power tool.

NAME OF PARTS

SPECIFICATIONS

Model G18MR G23MR

Motor Single-Phase Series Commutator Motor

Power Source Single-Phase 120 V AC 60 Hz / DC

Current 15 A

No-Load Speed 6000/min

Wheel Size:

External diam. 7" (180 mm) 9" (230 mm)

Hole diam. 7/8" (22 mm) 7/8" (22 mm)

Weight 11.9 lbs (5.4 kg)

English

ASSEMBLY AND OPERATION

APPLICATIONS

䡬 Removal of casting fin and finishing of various type of steel, bronze and aluminum

materials and castings.

䡬 Grinding of welded sections or sections cut by means of an acetylene torch.

䡬 Grinding of synthetic resins, slate, brick, marble.

WARNING: To avoid the risk of serious injury, NEVER use this grinder with cup

wheels and/or saw blades.

PRIOR TO OPERATION

1. Power source

Ensure that the power source to be utilized conforms to the power source requirements

specified on the product nameplate.

2. Power switch

Ensure that the switch is in the OFF position. If the plug is connected to a receptacle

while the switch is in the ON position, the power tool will start operating immediately

and can cause serious injury.

3. Extension cord

When the work area is far away from the power source, use an extension cord of

sufficient thickness and rated capacity. The extension cord should be kept as short as

practicable.

WARNING: Damaged cord must be replaced or repaired.

4. Check the receptacle

If the receptacle only loosely accepts the plug, the receptacle must be repaired. Contact

a licensed electrician to make appropriate repairs.

If such a fautly receptacle is used, it may cause overheating, resulting in a serious

hazard.

5. Check your work environment

Ensure the following before operation;

䡬 No flammable gas, liquid, or object at worksite.

䡬 When grinding thin steel sheet it may cause a high booming noise.

To avoid such noise, place a rubber mat under the workpiece.

䡬 Clear the area of children or unauthorized personnel.

English

Fig. 2

6. Mounting the wheel guard

Be sure to mount the wheel guard at an angle that will protect the operator’s body from

injury by a broken wheel piece.

[Installing and adjusting the wheel guard]

䡬 Open the lever and insert the locating pin

of wheel guard, bringing it into line with

the across flats of packing ground.

䡬 Then, turn the wheel guard to a desired

position (for use).

䡬 Close the lever and fix it. If and when

required, carry out adjustments by

tightening or loosening the screw.

䡬 If the lever does not move smoothly, apply

some lubricating oil to the sliding section

between the set piece and the lever.

Fasten the wheel guard at the position

where the across flats of the wheel guard

positioning pin and packing ground are

aligned (the position where the wheel

guard is inserted), but do not use it.

WARNING: If the wheel guard is not

attached properly, a broken

wheel may result in and

cause death or serious

injury.

7. Thoroughly check that the depressed center wheel is free of cracks, splits and

other abnomalities before mounting. Make sure it is firmly clamped and has

been properly mounted. Refer to page 14 of this manual for Depressed Center

Wheel Assembly and Disassembly.

8. Test the grinder before using

Before actually beginning the grinding work, test the grinder by first clearing the area

of all other personnel. Make sure the wheel guard is in place and that you are wearing

eye protection. Turn the grinder “on”, and make sure the grinder runs smoothly and

shows no abnormalities.

Duration of the trial run is as follows:

When depressed center wheel is replaced .................. 3 minutes or more

When starting daily work .............................................. 1 minute or more

9. Use only properly rated depressed center wheels

Use only depressed center wheels rated at 6600 RPM or more.

Using a depressed center wheel rated less can lead to wheel disintegration during

operation and cause serious bodily injury.

10. Check the push button

Make sure that the push button is disengaged by pushing push button two or three

times before turning on the grinder. (Fig. 5)

Locating Pin

Lever

Set Piece

Wheel Guard

Across

Flats

Packing Gland

Screw

English

GRINDER OPERATION

1. Hold the grinder firmly by its handle and side handle (Fig. 1)

The grinder produces a counterforce which must be controlled by firmly holding onto

the grinder.

2. Turn the grinder “on” (Fig. 3)

While holding the grinder firmly, use one

finger to switch to the “on” position.

Switch ON: Push the locking button forward

and then press the switch lever.

*For continuous use, press the

switch lever. The switch lever

is locked by pushing the

locking button forward once

again.

(*Subject to change depending on area.)

Switch OFF: Press and release the switch lever.

3. Use light grinding pressure

There is no need to press hard when grinding. Usually the grinder’s own weight is

sufficient to allow the required light contact with the surface to be ground.

WARNING: Do not press the grinder forcibly against the surface to be ground. Heavy

pressure can result in wheel breakage and serious injury. It can also

damage the surface being ground or damage the grinder’s motor.

4. Use proper grinding angle

Grind only with the wheel’s edge by lifting the grinder 15° to 30°, as shown in Fig. 4.

CAUTION:

● Do not use the entire surface of the depressed center wheel. Use only the edge of the

depressed center wheel.

5. Move the grinder in the proper direction

When using a new depressed center wheel

in direction A (Fig. 4), the wheel edge may

cut into the workpiece. In this case, grind

in direction B (Fig. 4).

Once the wheel edge is worn, the workpiece

can be ground in both directions.

NOTE: The wheel provided (resinoid wheel) is rated as Class A grain and # 24 grain size. It

is most suitable for heavy grinding of steel and other types of materials.

6. Adjust operation to desired finish

For a fine finish, decrease pressure by lifting slightly. Grind slowly and at the appropriate

speed.

Fig. 4

Fig. 3

Switch

Lever

Locking

Button

15°–30°

English

Fig. 5

CAUTION:

● The revolving depressed center wheel will create air turbulence.

Do no lay the grinder down in areas of dust or dirt until it has come to a complete

stop.

DEPRESSED CENTER WHEEL ASSEMBLY AND DISASSEMBLY

WARNING: Never attempt to assemble or disassemble the depressed center wheel,

unless the power switch is in the “OFF” position and the electrical

cord has been disconnected from the receptacle.

1. Assembly

(1) Turn the disc grinder upsidedown so that the spindle is facing upward.

(2) Align the oval-shaped indentation of the wheel washer with the notched part of the

spindle, then attach them.

(3) Fit the protuberance of the depressed center wheel onto the wheel washer.

(4) Screw the wheel nut onto the spindle.

(5) While pushing the push button with

one hand, lock the spindle by turning

the depressed center wheel slowly with

the other hand.

Tighten the wheel nut by using the

supplied wrench as shown in Fig. 5.

CAUTION:

● Tighten the wheel nut securely and confirm

that the depressed center wheel does not

wobble.

2. Disassembly

To remove the depressed center wheel,

simply reverse the above-mentioned

procedure.

Depressed

Center Wheel

Push

Button

Wrench

Wheel

Guard

Wheel

Washer

Spindle

Wheel Nut

Tighten

English

Fig. 6

Fig. 7

Carbon

Brush

Spring

Brush Holder

Wear limit

0.26" (6.5mm)

No. of carbon

brush

0.89" (22.5mm)

MAINTENANCE AND INSPECTION

WARNING: Be sure to switch power OFF and disconnect the plug from the receptacle

during maintenance and inspection.

Using cracked, deformed or damaged wheels can lead to wheel

breakage and resulting serious injury.

1. Replacing the depressed center wheel

Replace the depressed center wheel when it has been worn out to about 2-3/8" (60mm)

in external diameter. Confirm that there is no crack or any damage to the depressed

center wheel. If there is a crack or a transformation in the wheel, replace it immediately.

2. Inspecting the screws

Regularly inspect all screws and ensure that they are fully tightened. Should any of the

screws be loosened, retighten them immediately.

WARNING: Using this grinder with loosened screws is extremely dangerous.

3. Confirm that there is no damage in the

wheel guard, the electrical cord and the

housing, etc.

Check that the on/off switch operates

normally.

4. Inspecting the carbon brushes (Fig. 6)

The motor employs carbon brushes which

are consumable parts. Replace the carbon

brush with a new one when it becomes

worn to its wear limit. Always keep carbon

brushes clean and ensure that they slide

freely within the brush holders.

CAUTION:

● Using this grinder with a carbon brush

which is worn in excess of the wear limit

will damage the motor.

NOTE: Use HITACHI carbon brush No. 61

indicated in Fig. 6.

䡬 Replacing carbon brushes:

(1) Loosen the D4 tapping screw retaining

the brush cover and remove the brush

cover.

English

(2) Use the auxiliary hexagonal wrench or small screwdriver to pull up the edge of the

spring that is holding down the carbon brush. Remove the edge of the spring toward

the outside of the brush holder.

(3) Remove the end of the pig-tail on the carbon brush from the terminal section of

brush holder and then remove the carbon brush form the brush holder.

(1) Insert the end of the pig-tail of the carbon brush in the terminal section of brush

holder.

(2) Insert the carbon brush in the brush holder.

(3) Use the auxiliary hexagonal wrench or small screwdriver to return the edge of the

spring to the head of the carbon brush.

(4) Mount the tail cover and tighten the D4 tapping screw.

5. Service and repairs

All quality power tools will eventually require servicing or replacement of parts because

of wear from normal use. To assure that only authorized replacement parts will be

used, all service and repairs must be performed by a HITACHI AUTHORIZED SERVICE

CENTER, ONLY.

6. Service parts list

A: Item No.

B: Code No.

C: No. Used

D: Remarks

CAUTION:

● Repair, modification and inspection of Hitachi Power Tools must be carried out by a

Hitachi Authorized Service Center.

This Parts List will be helpful if presented with the tool to the Hitachi Authorized

Service Center when requesting repair or other maintenance.

In the operation and maintenance of power tools, the safety regulations and standards

prescribed in each country must be observed.

MODIFICATIONS: Hitachi Power Tools are constantly being improved and modified to

incorporate the latest technological advancements.

Accordingly, some parts (i.e. code numbers and/or design) may be

changed without prior notice.

01e_g18mr_e.p65 5/11/04, 0:10 PM16

English

ACCESSORIES

WARNING: Never use any accessories other than those mentioned below.

The use of any accessories other than those mentionded below or

attachments not intended for use such as cup wheel, cut-off wheel or

saw blade is dangerous and may cause personal injury or property

damage.

NOTE: Accessories are subject to change without any obligation on the part of the HITACHI.

STANDARD ACCESSORIES

䡬 Wrench (Code No. 937913Z) ............................................................................................... 1

䡬 Side Handle (Code No. 322411) .......................................................................................... 1

OPTIONAL ACCESSORIES..... sold separately

䡬 Depressed center wheel (10pcs. per package)

7" (180 mm) external dia. × 1/4" (6 mm) thickness × 7/8" (22 mm) hole dia.

(Code No. 701070)

9" (230 mm) external dia. × 1/4" (6 mm) thickness × 7/8" (22 mm) hole dia.

(Code No. 701090)

NOTE: Specifications are subject to change without any obligation on the part of the

HITACHI.

Français

INFORMATIONS IMPORTANTES DE SÉCURITÉ

Lire et comprendre toutes les précautions de sécurité, les avertissements et les instructions

de fonctionnement dans ce mode d’emploi avant d’utiliser ou d’entretenir cet outil motorisé.

La plupart des accidents causés lors de l’utilisation ou de l’entretien de l’outil motorisé

proviennent d’un non respect des règles ou précautions de base de sécurité. Un accident

peut la plupart du temps être évité si l’on reconnaît une situation de danger potentiel avant

qu’elle ne se produise, et en observant les procédures de sécurité appropriées.

Les précautions de base de sécurité sont mises en évidence dans la section “SECURITE”

de ce mode d’emploi et dans les sections qui contiennent les instructions de fonctionnement

et d’entretien.

Les dangers qui doivent être évités pour prévenir des blessures corporelles ou un

endommagement de la machine sont identifiés par AVERTISSEMENTS sur l’outil motorisé

et dans ce mode d’emploi.

NE JAMAIS utiliser cet outil motorisé d’une manière qui n’est pas spécifiquement

recommandée par HITACHI.

SIGNIFICATION DES MOTS D’AVERTISSEMENT

AVERTISSEMENT indique des situations potentiellement dangereuses qui, si elles sont

ignorées, pourraient entraîner la mort ou de sérieuses blessures.

PRECAUTION indique des situations dangereuses potentilles qui, si elles ne sont pas évitées,

peuvent entraîner de mineures et légères blessures ou endommager la machine.

REMARQUE met en relief des informations essentielles.

Français

SECURITE

REGLES GENERALE DE SECURITE

AVERTISSEMENT : Lire et coxmprendre toutes les instructions.

Un non respect de toutes les instructions ci-dessous peut

entraîner une électrocution, un incendie et/ou de sérieuses

blessures personnelles.

CONSERVER CES INSTRUCTIONS

1. Zone de travail

(1) Garder la zone de travail propre et bien éclairée. Les établis mal rangés et les

zones sombres invitent aux accidents.

(2) Ne pas utiliser les outils motorisés dans une atmosphère explosive, telle qu’en

présence de liquides inflammables, de gaz ou de poussières. Les outils motorisés

créent des étincelles qui risquent d’enflammer la poussière ou les vapeurs.

(3) Tenir les spectateurs, les enfants et les visiteurs éloignés, lors de l’utilisation de

l’outil motorisé. Une distraction peut faire perdre le contrôle de la machine.

2. Sécurité électrique

(1) Les outils à double isolation sont équipés d’une fiche polarisée (une lame est plus

large que l’autre). Cette fiche ne pénétrera dans une prise secteur polarisée que

dans un sens. Si la fiche ne rentre pas complètement dans la prise, la retourner. Si

elle ne rentre toujours pas, contacter un électricien qualifié pour installer une prise

polarisée. Ne pas modifier la fiche d’aucune façon. La double isolation

élimine

le besoin d’un cordon d’alimentation à trois fils et d’un système d’alimentation

avec mises à la terre.

(2) Eviter tout contact corporel avec les surfaces mises à la terre telles que les

canalisations, les radiateurs, les réchauds et les réfrigérateurs. Il y a un risque

accru d’électrocution si son corps est mis à la terre.

(3) Ne pas exposer les outils motorisés à la pluie ou à l’humidité. De l’eau pénétrant à

l’intérieur de l’outil motorisé augmente le risque d’électrocution.

(4) Ne pas maltraiter le cordon d’alimentation. Ne jamais utiliser le cordon pour porter

les outils ni tirer dessus pour débrancher la fiche de la prise. Garder le cordon à

l’écart de la chaleur, de la graisse, des arêtes coupantes ou des pièces en

mouvement. Remplacer immédiatement les cordons endommagés. Des cordons

endommagés augmentent les risques d’électrocution.

(5) Lors de l’utilisation d’un outil motorisé, utiliser un cordon de rallonge extérieur

marqué “W-A” ou “W”. Ces cordons sont prévus pour une utilisation extérieure et

réduisent les risques d’électrocution.

3. Sécurité personnelle

(1) Rester sur ses gardes, regarder ce que l’on fait et utiliser son sens commun lors de

l’utilisation d’un outil motorisé. Ne pas utiliser un outil en état de fatigue ou sous

l’influence de drogues, d’alcool ou de médicaments. Un moment d’inattention lors

de l’utilisation de l’outil motorisé peut entraîner de sérieuses blessures personnelles.

Français

(2) S’habiller correctement. Ne pas porter des vêtements larges ou des bijoux. Attacher

les cheveux longs. Tenir ses cheveux, vêtements et ses gants éloignés des parties

mobiles. Les vêtements larges, les bijoux et les cheveux longs peuvent se prendre

dans les parties mobiles.

(3) Eviter tout démarrage accidentel. S’assurer que le l’interrupteur d’alimentation

est sur la position d’arrêt avant de brancher la machine. Transporter l’appareil

avec les doigts sur l’interrupteur d’alimentation ou brancher un outil avec

l’interrupteur sur la position marche invite aux accidents.

(4) Retirer les clefs d’ajustement ou les commutateurs avant de mettre l’outil sous

tension. Une clef qui est laissée attachée à une partie tournante de l’outil peut

provoquer une blessure personnelle.

(5) Ne pas trop présumer de ses forces. Garder en permanence une position et un

équilibre correct. Une position et un équilibre correct permettent un meilleur contrôle

de l’outil dans des situations inattendues.

(6) Utiliser un équipement de sécurité. Toujours porter une protection pour les yeux.

Utiliser un masque à poussière, des chaussures de sécurité antidérapantes, un

casque dur et une protection pour les oreilles dans les conditions appropriées.

4. Utilisation de l’outil et entretien

(1) Utiliser un étau ou toutes autres façons de fixer et maintenir la pièce à usiner sur

une plate-forme stable. Tenir la pièce avec la main ou contre son corps est instable

et peut conduire à une perte de contrôle de l’outil.

(2) Ne pas forcer sur l’outil. Utiliser l’outil correct pour l’application souhaitée. L’outil

correct réalisera un meilleur et plus sûr travail dans le domaine pour lequel il a été

conçu.

(3) Ne pas utiliser un outil s’il ne se met pas sous ou hors tension avec un interrupteur.

Un outil qui ne peut pas être commandé avec un interrupteur est dangereux et doit

être réparé.

(4) Déconnecter la fiche de la source d’alimentation avant de réaliser tout ajustement,

changement d’accessoires ou pour ranger l’outil. De telles mesures de sécurité

réduisent le risque que l’outil ne démarre accidentellement.

(5) Ranger les outils inutilisés hors de la portée des enfants et des autres personnes

inexpérimentées. Les outils sont dangereux dans les mains de personnes

inexpérimentées.

(6) Conserver les outils avec soin. Garder les outils de coupe aiguisés et propres. Des

outils bien entretenus, avec des lames coupantes aiguisées risquent moins de se

gripper et sont plus faciles à contrôler.

(7) Vérifier les défauts d’alignement ou grippage des parties mobiles, les ruptures

des pièces et toutes les autres conditions qui peuvent affecter le fonctionnement

des outils. En cas de dommage, faire réparer l’outil avant de l’utiliser. Beaucoup

d’accidents sont causés par des outils mal entretenus.

(8) Utiliser uniquement les accessoires recommandés par le fabricant pour le modèle

utilisé. Des accessoires qui peuvent convenir à un outil, peuvent devenir dangereux

lorsqu’ils sont utilisés avec un autre outil.

5. Réparation

(1) La réparation de l’outil ne doit être réalisée uniquement par un réparateur qualifié.

Une réparation ou un entretien réalisé par un personnel non qualifié peut entraîner

des risques de blessures.

La page charge ...

Hitachi G23MR - 9" Disc Grinder Manuel utilisateur

Marque: Hitachi

Modèle: G23MR - 9" Disc Grinder

Catégorie: Meuleuses d'angle

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Hitachi G23MR - 9" Disc Grinder User manual
español: Hitachi G23MR - 9" Disc Grinder Manual de usuario

Hitachi G23MR - 9" Disc Grinder Manuel utilisateur

Ce manuel convient également à

Hitachi G23MR - 9" Disc Grinder Manuel utilisateur

dans d''autres langues

Documents connexes