Russonud XZone70V Streaming Mixer Amplifier Guide d'installation

Marque: Russonud

Modèle: XZone70V Streaming Mixer Amplifier

Taper: Guide d'installation

Ce manuel convient également à

XZone70V

Streaming Mixer Amplier

Installation Manual

XZone70V Streaming Audio Ampliﬁer

Level

System VolumeMic Volume

Clip

2 XZone70V Installation Manual

NOTICE:

IF YOU ARE NOT A RUSSOUND CERTIFIED INSTALLER,

YOU WILL NOT BE ABLE TO INSTALL AND CONFIGURE

THIS PRODUCT

INTERNET CONNECTION REQUIRED

FOR PRODUCT INSTALLATION

There are two things that must be done at the time of installation of this

product that require a working internet connection:

1. Enter valid Russound Certied Installer credentials. The XZone70V is

shipped in a locked state. It cannot be operated without rst being congured

by a Russound Certied Installer.

If you are a custom installation professional and wish to become authorized as a

Russound Certied Installer, please contact your Russound Sales Representative

for more information.

Note: If you are a Russound Certied Installer and you plan on installing this

product on a job site that may not have working internet access, please

congure the unit at your shop or other location where internet access is

available BEFORE you take it to the job site.

2. Firmware may be updated easily through Web Cong conguration. An

internet connection is required for obtaining the most recent rmware.

Note: If an internet connection will not be available at the place of installation,

please download the latest rmware from the Russound website to a laptop

before going to the job site.

Installer Credential Entry

When the XZone70V is shipped from Russound, it will only operate in a "locked"

state. In this state, no audio or control is available. In order to unlock the system,

valid Russound Certied Installer credentials must be entered using the Web

Cong.

When the XZone70V is rst powered on, a message will appear on any

compatible user interfaces and the MyRussound App indicating that the device

must be unlocked. The message will contain the IP address of the XZone70V.

Using your mobile device or computer, browse to the XZone70V IP address (type

http:// and then the IP address).

If you are using the MyRussound App, the IP address appears as a link that will

direct you to Web Cong via your local web browser.

If you do not have a valid Russound Certied Installer credential, please

contact your Russound Sales Representative.

Lockdown Feature

RUSSOUND CERTIFIED INSTALLER REQUIRED

3XZone70V Installation Manual

Product Overview ................................................................................................................... 3

Web Conguration.................................................................................................................. 4

Front and Back Panel ..............................................................................................................5

Ethernet Connection and Factory Reset ......................................................................... 6

Installation Overview ......................................................................................................... 6-8

Conguration ............................................................................................................................9

Network Settings ................................................................................................................... 10

Conguration Streaming Service Accounts ................................................................. 11

Troubleshooting ....................................................................................................................11

Connection Diagrams ..........................................................................................................12

70/100V Wiring .......................................................................................................................13

Troubleshooting ....................................................................................................................14

Network Best Practices ........................................................................................................15

Technical Specications ......................................................................................................15

Limited Warranty ...................................................................................................................16

Safety Instructions ......................................................................................................... 18-19

TABLE OF CONTENTS

Product Overview

Thank you for choosing the Russound XZone70V Streaming Mixer Amplier

as your audio solution. The Russound XZone70V features built-in XStream

technology, enabling popular streaming content from the cloud, local

network, AirPlay™ enabled tablets and phones - all from a single component.

The built-in audio streamer oers the best audio content from the internet or

even a user’s personal networked audio collection using DLNA. The rear panel

includes an auxiliary input port and USB port for playing content from a Flash

Drive or an externally powered USB hard drive.

PRODUCT OVERVIEW

Features:

• Full Support for High Res Audio

• Licensed Music Option for Commercial Music Performance

• Powerful High Quality 70v/100v/4Ω Amplier

• Integrated Mic Input With Ducking And Support For Phantom Power

• Wall-Mounted Touchscreen or App Control

• Built-In High Pass Filter

• Auxiliary Input Option Included

• Removable Screw-down Connectors

• Flexible Mounting Options

• Trusted 2-year Warranty

Conguration Password

In order to prevent unauthorized changes to conguration settings, a default

password of russound123 has been created that will be required to be

entered prior to changing any conguration settings. Enter this password

when prompted for a Conguration Password.

This password is separate from the Russound Certied Installer password that

is used to unlock the controller and cannot be modied.

4 XZone70V Installation Manual

Key Programming Features

The XZone70V has a programming feature called Web Config. This program-

ming feature allows the installer to connect to the XZone70V via its IP address

or Host Name using any smartphone, tablet, or laptop and configure it.

Web Config is designed to be used with a web browser. With Web Config, the

XZone70V can be completely configured, quickly and easily, with no other

software tools required

Web Cong Features

• General network configuration (DHCP/static IP)

• Firmware Updates

• Assign device name (zone name)

• Zone Volume Trim

• Set AirPlay password (if desired)

• Enable/disable or re-order streaming services

• Enable/disable front panel LED’s (for use in installations where light

pollution is a concern, such as bedrooms)

WEB CONFIGURATION

Web Config status page.

5XZone70V Installation Manual

XZone70V Streaming Audio Ampliﬁer

Level

System VolumeMic Volume

Clip

XZone70V Streaming Audio Ampliﬁer

Level

System VolumeMic Volume

Clip

FRONT AND BACK PANEL

Power Button Status LEDsSystem

Volume Control

Ethernet

Port

Factory

Reset

USB Port

AC Input

Power Button - Turns the XZone70V on/o.

Output Level Indicator - LEDs will illuminate sequentially from left to right to

indicate increasing output levels. Red indicates that the amplifier has begun clipping.

Reduce the volume level when clipping is reached.

Microphone Volume Control - Adjust the microphone volume level here to in-

crease the microphone volume in relation to the background audio.

System Volume - Use these volume buttons to increase/decrease the overall system

volume level. These buttons are similar to pressing volume up/down on the XTS or the

MyRussound app.

Status LEDs - Troubleshooting - See LED diagnostic chart on page 11

Ethernet Port - The Ethernet port is used for configuration as well as for enabling

control via the MyRussound App or the XTS Touchscreen. The default network setting is

DHCP-enabled, but the XZone70V can be configured with a static IP address using the

Web Config interface.

USB Port - For audio from flash drives or externally powered USB hard drives

Factory Reset - The factory reset button has two functions. A 3-second press and

hold will restore network settings to DHCP. A 10-second press and hold will reset the

XZone70V to its factory default settings.

Note: A unit that has been reset to factory default will have no configuration and will

need to be unlocked and reconfigured by a Russound Certified Installer. Network

connections will also default back to DHCP during a reset.

Microphone Gain Control/Input - Connect a microphone here. If using a con-

denser microphone, set the Phantom Power switch to "On". Refer to "Adjusting the

Microphone Gain" section on page 12 for more information.

Phantom Power Switch - Set this switch to "On" when using a condenser micro-

phone or when the microphone instructions specify using Phantom Power support.

Mode 70/100V or 4Ω Switch - Like any premium audio component, the XZone70V

uses a high pass filter when operating at 70/100v. If using as a low impedance ampli-

fier (minimum 4 ohm), set this switch to the 4Ω position. Otherwise, leave it at the

70/100V position.

Audio In - Connect any stereo audio source to this connection. This input is selectable

from the XTS touchscreen or the MyRussound app and has AUX input.

Pre-Out Left and Right - Balanced pre-out connections for both left and right audio

channels for connecting to additional amplifiers

Speaker Output - Refer to "Speaker Connections" on page 12.

AC input - Voltage is autoswitching for 100V to 240V operation 50-60 Hz. This recep-

tacle accepts a 3-prong IEC C13 type connector. A detachable 3-terminal power cord is

included.

Pre-Out

Left and Right

Speaker

Out

Audio In

Microphone

Gain Control/Input

Phantom

Power Switch

Mode 70/100V or 4 Ω Switch

Microphone

Volume Control

Output Level

Indicator

6 XZone70V Installation Manual

ETHERNET CONNECTION AND FACTORY RESET

Ethernet Connection

The Ethernet connection is used for conguration and audio streaming as well as

for enabling control via the MyRussound App or the XTS Touchscreen. The default

network setting is DHCP-enabled, but the XZone70V can be congured with static

IP addressing using Web Cong. The Ethernet connection is also used for the built-

in streaming services and for playing any music stored on connected network

drives using DLNA.

Note: While the XZone70V has a single physical Ethernet connection, it will

occupy a total of 2 IP addresses on the network. One address is for XZone70V

management, and the other is for the internal streaming module that the

XZone70V utilizes to provide audio content. If using DHCP, both addresses will use

DHCP. If using static IP addressing, both addresses will need to be congured with

a static address.

Factory Reset

The factory reset button has two functions. A 3-second press and hold will restore

network settings to DHCP. A 10-second press and hold will reset the XZone70V to

its factory default settings. When performing either of these functions, do not

power o the XZone70V. It will reboot automatically on its own at the proper

time. The entire reset process will take several minutes. The XZone70V status LED

will illuminate green when the process is complete.

The factory reset deletes all conguration and personal information including

service account settings and passwords.

Note: After a factory reset, the XZone70V will require valid Russound Certied

Installer credentials in order to be unlocked and congured again.

INSTALLATION OVERVIEW

Installation

Step 1. Mounting the XZone70V

The XZone70V comes with a pair of rack mount ears,

that allows XZone70V to be mounted in any of four ways:

Installation

Clearance Requirements

When installing the XZone70V, the clearances shown here MUST be kept for

proper ventilation of the unit.

2. Rack Mount

Attach the included rack mount ears to both sides of the unit as shown.

3. Under Cabinet Mount

Attach the included rack

mount ears to both sides of

the unit, with mounting ears

facing up as shown.

4. Wall Mount

Attach the included rack

mount ears to both sides of the

unit, with mounting ears facing

up as shown.

Top of the unit

Rack mount ear

1. Table Top Mount

1.75” (4.4cm)

XZone70V Streaming Audio Ampliﬁer

Level

System VolumeMic Volume

Clip

7XZone70V Installation Manual

Important Considerations

1. Disconnect the power cord before making any wiring connections to the

XZone70V.

2. Verify that all connections and polarity are correct.

3. Keep all power cords away from all signal cables to prevent humming

caused by induced noise.

4. Label wires appropriately, on both ends of the wire run.

5. Avoid running speaker wires or signal cables close to house electrical

wiring for any distance. If you have to run them parallel, make sure to space

the wires at least two feet from the AC line. If you need to cross an AC line it

should be at a 90° angle.

Step 2. Connect the speaker wires as described in Speaker Connections on

page 12.

a. Strip back 1/8” of the insulation on the speaker wire and twist the end of

each wire to tighten the bundle of copper strands on each wire.

b. Place the stripped end of the wire into the appropriate terminal and

collapse the latch. Check to make sure there are no strands of copper

showing and check the security of the wire in the connector. Between each

terminal, take caution to not let the wire fray or touch another connection.

Each terminal accepts up to 14 AWG wire.

c. Connect to each speaker. Be careful to maintain polarity.

d. Re-connect the screw-down speaker terminal.

Make sure to label the speaker wire with the zone name that it is connected to.

This will allow easier system maintenance in the future.

Step 3. Connect an Ethernet cable from an open network port on the network

to the Ethernet port on the rear of the XZone70V.

Step 4. Connect the power cord to the rear of the XZone70V and then plug the

other end into an electrical outlet.

Step 5. Depress the power button on the front of the XZone70V to power on

the unit.

The XZone70V will take 1-2 minutes to fully power up. The amber LED on the

front panel will illuminate during the power-up process. When the green LED

on the front panel is illuminated, you are ready to proceed.

Step 6. Unlock the XZone70V – Using a smartphone, tablet, or laptop, navigate

to the XZone70V Web Cong main page by typing in one of the following:

a. XZone70V IP address – Enter the IP address of the XZone70V into

the web browser on your phone, tablet, or PC connected to the same

network as the XZone70V. Example: if the IP address is 192.168.0.105, type

http://192.168.0.105 into the web browser. Note: If you don’t know the

IP address, you can use a network scanning app such as FING (free for iOS

and Android) to discover the IP address of the XZone70V. The device name

you will be searching for in the FING device list is “XZone70V-XXXX” where

XXXX are the last four digits of the MAC ID of the XZone70V.

b. XZone70V Hostname – Enter the hostname of the XZone70V into the

web browser on your phone, tablet, or PC connected to the same network

as the XZone70V. For your convenience, the hostname is printed on a label

on the rear of the XZone70V. The hostname is formatted as XZone70V-

XXXX where XXXX is the last four digits of the XZone70V’s MAC ID.

Example: if the hostname is XZone70V-1234, type http://XZone70V-1234

into the web browser.

INSTALLATION OVERVIEW

8 XZone70V Installation Manual

INSTALLATION OVERVIEW

Step 7. Firmware Update – Because new features and capabilities may

be added at any time, make sure to verify that the XZone70V has the latest

rmware available. From the Web Cong page, go to Admin, Firmware Update.

If the XZone70V has an internet connection, it will automatically verify if it is

running the latest rmware from Russound. You may update the XZone70V

by selecting Web Update for any XZone70V with an internet connection, or

by choosing File Update to update the XZone70V from a rmware update le

stored on a computer that is on the same network as the XZone70V.

Note: It can take 10-15 minutes for a rmware update to be completed.

The front panel status LED will illuminate a steady green when the update is

completed.

Automatic Firmware Updates

The XZone70V is congured by default with Automatic Firmware Updates

Enabled. This means that it will check for an update to its rmware periodically

with Russound’s servers. This check will happen at the time congured in Web

Cong under System Settings. The default time setting is set for early AM/

overnight hours in the Eastern Time Zone of the US. You may set this time for

any convenient time in your time zone. We recommend around 3am, when

it is not likely that the system is in use because a reboot will occur during an

update.

You may disable the automatic update feature if you would like the ability to

control the exact time when an update occurs. We recommend this only for

advanced users because it will require the update to be activated either onsite,

or via a 3rd party remote management service such as ihiji, BakPak, or OvrC.

At the top of the web browser, a notication will appear stating that the

product must be unlocked by a Russound Certied Installer. Click on the unlock

button and you will be taken to a page where you will enter your credentials.

Enter your Russound Certied Installer Email Address and password into the

elds shown and click “Apply”. Once your information has been validated, the

XZone70V will unlock and be ready for conguration and use. This unlock

process will need to be repeated any time that the XZone70V is reset to factory

settings using the rear panel reset button.

9XZone70V Installation Manual

CONFIGURATION

Conguration of the XZone70V is done through Web Cong. Navigate to the

XZone70V Web Cong page (see Step 6 above)

Web Cong Setup Tab

Front Panel LEDs – The front panel LED lights can be disabled for any

installation where viewing the operational lights would be distracting, or

where complete darkness is desired at night. The default setting is enabled.

To disable the front panel LED’s, select “Disabled” for this option in Web Cong.

Note: Only normal operation LEDs are disabled. Any error condition LED

lights will always illuminate.

Device Name – Enter the desired zone name here. The name you enter will

be visible to all users of the MyRussound App or other user interfaces when

selecting the zone they would like to control.

Make sure to choose a unique name for each zone in the entire Russound

system.. If there are two rooms named “Bar” for example, users will not know

which zone they are selecting and controlling.

AirPlay Password (Optional) - If you want to use an AirPlay password to limit

access for AirPlay users to stream audio to the XZone70V, enter an AirPlay

password and click “Apply”. This same password must be entered on any iOS

device when attempting to use Apple AirPlay to stream audio. If you do not

want to use a password to control access to AirPlay, leave the AirPlay Password

eld blank.

Services - By default, all available audio services are enabled and are selectable

as options when streaming audio. If any of these services are not being used,

or if you wish to block access to any services for this, you can do so by dragging

and dropping the services between the “Enabled” and “Disabled” sections on

this Web Cong page.

Note: You can also re-order the services so that the services the end user

wants to use rst are at the top of the list. Simply drag and drop each service in

the “Enabled” list to the appropriate order that you would like them to appear

to the end user for each zone.

Volume Trim – The Volume Trim setting is used to allow an audio

compensation adjustment. In most cases, this setting does not need to be

modied, but if there are unusual audio characteristics such as for small

rooms, rooms lled with very reective surfaces like tiled oors and bare walls,

or rooms lled with highly absorptive materials like thick carpet and heavy

curtains, you can use the Volume Trim settings to tweak the sound levels.

The default setting for the Volume Trim level in each zone is -3 dB.

Congratulations! Your XZone70V is now fully congured.

10 XZone70V Installation Manual

NETWORKING SETTINGS (OPTIONAL)

Power

As an advanced networking device, the XZone70V is designed to be left on at

all times. This allows instant access to your favorite streaming audio sources at

any time and is especially useful due to the fact that most installations involve

locating the XZone70V in remote locations where it would be dicult to know

if it is powered on or o or to know its current status.

For extended periods of non-use, we recommend disconnecting the power

source to the XZone70V unit until it is needed again.

The XZone70V can be congured to use either a dynamic DHCP network

address (Default) or to use a pre-assigned static IP address. Note that the

XZone70V occupies two IP addresses on a network. One IP address is used

for communication and control information (HOST) and one is used for the

streaming services (STREAMER).

Both IP addresses are set using the Admin > Networking selection from the

Web Cong menu. Both can be set as dynamic (Default) or both can be set as

static IP addresses. Use caution when setting static IP addresses as incorrect

settings can cause network instability and cause networking products such as

the XZone70V or any other device on the network to stop working properly.

If static settings have been entered and you are experiencing diculty

communicating with the XZone70V, you can restore dynamic DHCP settings

by pressing the Reset button on the rear of the XZone70V and holding the

button pressed for 3 seconds.

When entering static IP information, two IP addresses must be assigned, one

for the Host and one for the Streamer. If DHCP is enabled on the network, use

caution to make sure that any static IP addresses assigned are not within the

range of possible DHCP addresses and that the addresses are not used for any

other networking device.

If necessary, change the Subnet Mask, Default Gateway, and DNS information

to the appropriate settings for your particular network.

Note: When changing the network address of the XZone70V, your browser

will lose its connection to the XZone70V and you will need to navigate to the

XZone70V’s new network address.

11XZone70V Installation Manual

CONFIGURATION STREAMING SERVICE ACCOUNTS (OPTIONAL)

Note: Conguring accounts must be done before accessing any streaming

source which requires an account such as SiriusXM, Pandora, or Spotify. If using

more than one XStream Series device, dierent accounts may be entered for

each zone if desired.

Spotify® – Spotify account credentials are entered in the Spotify app on your

phone, tablet, or PC. No additional information needs to be entered on the

XZone70V. Note that the name that you congured under “Device Name” will

be the same name that appears in the Spotify Connect menu as an available

selection. This same name is also the name used when connecting via Apple

AirPlay.

Pandora®– Pandora account credentials are entered by using the MyRussound

App or a connected Russound XTS in-wall touchscreen. Choose “Pandora”

from the menu. If no account information has been entered, a login screen will

be displayed.

SiriusXM® – SiriusXM account credentials are entered by using the

MyRussound App or a connected Russound XTS in-wall touchscreen. Select

SiriusXM as the active audio source. If no account information has been

entered, a login screen will be displayed.

vTuner® – No account information is needed to access vTuner internet radio.

If you wish to associate an XZone70V with a vTuner account so that you can

share vTuner favorites across multiple devices, you can select “Get Access

Code” from the vTuner menu and enter that code at http://russound.vtuner.

com to associate the Streamer with your vTuner account.

TuneIn® – No account information is needed to access Tunein internet radio.

If you wish to associate a zone’s Streamer with a TuneIn account so that you

can share TuneIn favorites across multiple devices, you can select “Account

Association” from the zone’s TuneIn menu and enter that code in your account

settings page at http://www.tunein.com to associate the Streamer with your

TuneIn account.

DHCP Reset

A DHCP Reset can be performed using the factory reset button on the rear

panel of the XZone70V.

If your XZone70V cannot communicate on the network, you can reset its

DHCP connection by pressing and holding the Reset button on the rear of the

XZone70V for 3 seconds and then releasing it. This will restore the XZone70V to

a DHCP connection from a static IP connection.

Factory Reset

For a full factory reset, erasing all conguration settings, and re-locking the

XZone70V:

Press and hold the Reset button on the rear of the XZone70V for 10 seconds.

The Red Status LED will light and the XZone70V will reboot on its own.

Note: Performing a factory reset will restore the unit to its factory default

settings and the unit will require valid Russound Certied Installer credentials

in order to be unlocked and congured again. The factory reset will also delete

all personal information including service account settings and passwords.

There are four LED’s on the front panel of the XZone70V to assist with any troubleshooting.

This chart explains the operation of the LED’s:

TROUBLESHOOTING

System Status Yellow

LED

Green

LED

Red

LED

Blue

LED

Booting ON - - -

Ready - ON - -

Factory Reset - - ON -

Zone On - - - ON

Firmware Update - Blinking - -

Network Error Blinking - - -

12 XZone70V Installation Manual

CONFIGURATION

Connections

Microphone - A microphone with an on/o switch is recommended for use

with the XZone70V. Connect the microphone using the Phoenix connector on

the rear panel.

Automatic Ducking - The XZone70V will automatically reduce the volume of

any source when it detects an audio signal on the microphone input.

Adjusting the Microphone Gain - There are two dierent controls for

adjusting the microphone volume level on the XZone70V. In order to set the

appropriate level, we recommend following these steps:

1. Pause or Mute the currently playing audio source

2. Set the front panel Mic Volume control to maximum (clockwise rotation)

3. Set the rear panel Microphone Gain control to minimum (counter-

clockwise rotation)

4. While speaking into the microphone, slowly adjust the rear panel

Microphone Gain control until the volume level is at the maximum level

you want to achieve.

Note: The XZone70V must be turned on for the microphone to work. The input

works for any operational state of the XZone70V: playing music, paused, or

muted.

Speaker Connections

The XZone70V has three separate output options: 70-volt, 100-volt, and a low

impedance setting of 4Ω (Minimum). When connecting speakers, use the

appropriate connections for each application, see diagram below.

70V Connection

Speaker

XZone70V

70VCOM 4ΩCOM100VCOM70V COM

100V Connection

Speaker

XZone70V

100V COM

4Ω Connection

Speaker

XZone70V

4ΩCOM

XZone70V

Speaker

AW70V6

13XZone70V Installation Manual

70/100V WIRING

Wiring a 70/100V high impedance amplier like the XZone70V is much simpler

than a traditional low impedance residential amplier. All connections are

made in parallel and a thinner gauge wire may be used for a high impedance

system than a low impedance system. Typical wiring would use a 16 or 18

gauge wire in a single run from the amplier to all possible speaker locations

(now or to be added in the future). A small loop can be left at each potential

speaker location.

Adding a speaker at each wire loop is easy (either now, or in the future,

allowing for easy system updates at any time). See diagram below.

From

Amplier

To Additional

Speaker

14 XZone70V Installation Manual

TROUBLESHOOTING

General Troubleshooting

Check for rmware updates available to make sure that your Russound

product is always up to date and to take advantage of any additional features

or supporting services that may be available.

Many issues can be resolved by power cycling the XZone70V by disconnecting

the power supply, waiting 15 seconds and re-connecting the power supply.

For networking issues, resetting network gear in the home such as the router

or any switches between the XZone70V and the router may also resolve any

issues.

If you have the XZone70V congured with a static IP address and do not

remember the settings, you can reset the XZone70V to DHCP by pressing

and holding the rear panel Reset button for 3 seconds. If there are any issues

reconnecting to the XZone70V after resetting to DHCP, unplug the XZone70V

from the network and re-connect it, or try power cycling the network router to

force a new DHCP connection.

For audio connection issues, verify all audio connections from the XZone70V

to the speakers or any amplier/receiver.

For more system installation and network troubleshooting tips, visit

www.russound.com

15XZone70V Installation Manual

NETWORKING BEST PRACTICES

Networking Best Practices

Some of the most common problems can be caused by improper network

conguration and out-of-date rmware. Improper network conguration can

prevent XStream Series devices from connecting and communicating on the

network.

The rst step for troubleshooting is to check networking connections and

power cycle the equipment to check for proper communication.

A dedicated wireless 802.11n or better router is recommended. The reason

for this is that ISP supplied modem/router combination devices may have

incompatible settings that can cause issues with XStream Series devices

connecting or communicating across the network. It is recommended to not

use these modem/router combination devices, because the end user may not

have access to all services of the device. The ISP may have sole control over the

device settings and send updates to reset, reinitialize, or replace the device at

their discretion.

Check for rmware updates available for your Russound equipment to make

sure they are up-to-date in order to take advantage of any additional features

and supported services.

Use a network discovery and IP scanning application that can assist to better

understand the network, such as FING. http://overlooksoft.com/FING is free

and available for iOS and Android and can assist in identifying devices on the

network and if there are any IP addressing conicts.

Router Conguration:

A few routers may need additional conguration to prevent incompatibility

or intermittent connection issues. Access the router and check user accessible

settings that enable support for Multicast or IGMP and enable them or check

for options that may be actively ltering these protocols and disable those

lters. Check for other options that could have an eect on communication:

Options such as UPnP should be enabled Options such as IGMP Proxy, IGMP

Snooping, Multicast Filtering or WMM Proxy should be disabled.

Glossary

Multicast: The delivery of a message or information to a group of destination

computers simultaneously in a single transmission from the source.

Unicast: The delivery of a message or information which is sent from one point

to another point An example would be connecting to an IP address of a URL

such as www.google.com.

IGMP: Internet Group Management Protocol is an integral part of IP Multicast

and is used for one-to-many networking applications such as online streaming

audio and video, gaming, and allows more ecient use of resources when

supporting these types of applications.

WMM: Wireless Media Management is designed to support consumer and

corporate applications and works with 802.11a, 802.11b and 802.11g. The

specication provides basic prioritization of data packets based on four

categories - voice, video, best eort and background.

UPnP: Universal Plug and Play uses Multicast and allows media servers and

streaming devices to communicate.

TECHNICAL SPECIFICATIONS

Output Power: 300W Max

Output Modes: 70v/100v/4Ω

Analog Audio Input: 3.5mm stereo (rear panel)

Hi-Res Audio Support: 24-bit/192kHz

Number of Audio Channels: 1

Pre-Amp Output: Stereo Balanced

Mic Input: 1

Frequency Response: 20Hz to 20kHz +1/-1dB at 4 Ohms

Communication ports: Ethernet and USB (for music les)

Music File Formats: MP3 (CBR, VBR), WAV (8, 16-bit),

OGG Vorbis, FLAC (8, 16-bit). AAC, AAC+

(supports up to 24-bit/192 kHz)

Total Harmonic Distortion: 1% THD+N at 300W into 4 ohms

0.2% THD+N at 250W into 4 ohms

Power Requirements: Input: 100-240V~50/60Hz 240W

Dimensions: 17" W x 9"D x 1.7"H (43 x 22.8 x 4.3cm)

Weight: 10.95 lbs (5 kg)

16 XZone70V Installation Manual

LIMITED WARRANTY

The Russound XZone70V is guaranteed against all defects in materials and workmanship

for two (2) years from the date of purchase. During this period, Russound will replace any

defective parts and correct any defect in workmanship without charge for either parts

or labor.

For this warranty to apply, the unit must be installed and used according to its written

instructions. If service is necessary, it must be performed by Russound. The unit must

be returned to Russound at the owner’s expense and with prior written permission.

Accidental damage and shipping damage are not considered defects, nor is damage

resulting from abuse or from servicing by an agency or person not specically authorized

in writing by Russound.

This Warranty does not cover:

• Damage caused by abuse, accident, misuse, negligence, or improper installation or

operation

• Power surges and lightning strikes

• Normal wear and maintenance

• Products that have been altered or modied

• Any product whose identifying number, decal, serial number, etc. has been altered,

defaced or removed.

Russound sells products only through authorized Dealers and Distributors to ensure that

customers obtain proper support and service. Any Russound product purchased from

an unauthorized dealer or other source, including retailers, mail order sellers and online

sellers will not be honored or serviced under existing Russound warranty policy. Any sale

of products by an unauthorized source or other manner not authorized by Russound

shall void the warranty on the applicable product.

Damage to or destruction of components due to application of excessive power voids

the warranty on those parts. In these cases, repairs will be made on the basis of the retail

value of the parts and labor. To return for repairs, the unit must be shipped to Russound

at the owner’s expense, along with a note explaining the nature of service required. Be

sure to pack the unit in a corrugated container with at least three (3) inches of resilient

material to protect the unit from damage in transit.

Before returning a unit for repair, call Russound at (603) 659-5170 for a Return

Authorization number. Write this number on the shipping label and ship to:

Russound

ATTN: Service

1 Forbes Road

Newmarket, NH 03857

Due to continual eorts to improve product quality as new technology and techniques

become available, Russound/FMP, Inc. reserves the right to revise system specications

without notice.

17XZone70V Installation Manual

18 XZone70V Installation Manual

The lightning ash with arrowhead symbol,

within an equilateral triangle, is intended to

alert the user to the presence of uninsulated

dangerous voltage within the product’s

enclosure that may be of sucient magnitude

to constitute a risk of electric shock to persons.

The exclamation point within an equilateral

triangle is intended to alert the user to

the presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

Safety Instructions

1. Read Instructions - All the safety and operating

instructions should be read before the appliance is

operated.

Lisez les instructions - Toutes les instructions de sécurité

et doivent être lues avant d'utiliser l'appareil.

2. Retain Instructions - The safety and operating

instructions should be retained for future reference.

Conservez les instructions - Les instructions de sécurité et

devrait être conservé pour référence future.

3. Heed Warnings - All warnings on the appliance in the

operating instructions should be adhered to.

Tenez compte des avertissements - Tous les

avertissements gurant sur l'appareil dans les instructions

de fonctionnement doivent être respectées.

4. Follow Instructions - All operating and user instructions

should be followed.

Suivez les instructions - Toutes les instructions de

fonctionnement et d'utilisation doivent être suivies.

5. Water and Moisture - The appliance should not be

used near water; for example, near a bathtub, washbowl,

kitchen sink, laundry tub, in a wet basement, or near a

swimming pool. The apparatus shall not be exposed to

dripping or splashing liquids and no objects lled with

liquids, such as vases, shall be placed on the apparatus.

Do not touch the appliance with wet hands. Do not

handle the appliance or power cord with wet or damp

hands. If water or any other liquid enters the appliance

cabinet, take it to qualied service personnel for

inspection.

Eau et humidité - L'appareil ne doit pas être utilisé près

de l'eau, par exemple près d'une baignoire, d'un lavabo,

d'un évier, machine à laver, dans un sous-sol humide ou

près d'une piscine. L'appareil ne doit pas être exposé à

des éclaboussures de liquides et aucun objet rempli de

liquide, comme des vases, ne doit être posé sur l'appareil.

Ne pas toucher l'appareil avec les mains mouillées. Ne

manipulez pas l'appareil ou le cordon d'alimentation

avec les mains mouillées ou humides. Si de l'eau ou

tout autre liquide pénètre dans le coret de l'appareil, il

amène à un personnel qualié pour l'inspection.

6. Cleaning - The appliance should be cleaned only as

recommended by the manufacturer. From time to time

you should wipe o the front and side panels and the

cabinet with a soft cloth. Do not use rough material,

thinners, alcohol or other chemical solvents or cloths

since this may damage the nish or remove the panel

lettering.

Nettoyage - L'appareil doit être nettoyé uniquement tel

que recommandé par le fabricant. De temps en temps

vous devriez essuyer les panneaux latéraux avant et

arrière et le boîtier avec un chion doux. Ne pas utiliser de

matériel rugueux, de diluant, d'alcool ou d'autres solvants

chimiques ou de chions car cela pourrait endommager la

nition ou faire disparaître la sérigraphie du boîtier.

7. Ventilation - The appliance should be situated so that

its location or position does not interfere with its proper

ventilation. For example, the appliance should not be

situated on a bed, sofa, rug, or similar surface that may

block the ventilation openings, or placed in a built-in

installation, such as a bookcase or cabinet that may

impede the ow of air through the ventilation openings.

Place the unit in a well-ventilated location, leaving at least

2 inches (5 cm) of clearance on all sides, top and rear of

unit for air ow. If ventilation is blocked, the unit may

overheat and malfunction.

Ventilation - L'appareil doit être placé de telle sorte que

son emplacement ou sa position ne gêne pas sa propre

ventilation. Par exemple, l'appareil ne doit pas être placé

sur un lit, un canapé, un tapis ou une surface similaire qui

pourrait obstruer les ouvertures de ventilation, ou placés

dans un haut-installation, comme une bibliothèque ou

un meuble qui pourrait empêcher le ux d'air à travers

les ouvertures de ventilation. Placer l'appareil dans un

endroit bien aéré, laissant au moins 2 pouces (5 cm) de

dégagement de tous les côtés, en haut et à l'arrière de

l'unité de circulation de l'air. Si la ventilation est bloqué,

l'appareil peut surchauer et mal fonctionner.

8. Heat - The appliance should be situated away from heat

sources such as radiators, heat registers, stoves, or other

appliances (including ampliers) that produce heat.

Chaleur - L'appareil doit être placé loin des sources de

chaleur telles que des radiateurs, registres de chaleur,

poêles ou autres appareils (incluant les amplicateurs) qui

produisent de la chaleur.

9. Grounding or Polarization - Precaution should be

taken so that the grounding or polarization means of an

appliance is not defeated.

La terre ou polarisation - précautions doivent être

prises pour que les moyens d'un appareil à la terre ou

polarisation ne soit pas annulée.

10. Power Cord Protection - Power supply cords should

be routed so that they are not likely to be walked on or

pinched by items placed upon or against them, paying

particular attention to cords at plugs, receptacles, and the

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE THE COVER. NO

USER-SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE PERSONNEL.

ATTENTION: AFIN DE RÉDUIRE LE RISQUE

DE CHOC ÉLECTRIQUE, NE PAS RETIRER LE

CAPOT. AUCUNE PIÈCE À L'INTÉRIEUR. CONFIER

L'ENTRETIEN DE PERSONNEL QUALIFIÉ.

WARNING: TO REDUCE THE RISK OF FIRE

OR ELECTRIC SHOCK, DO NOT EXPOSE THIS

APPLIANCE TO RAIN OR MOISTURE.

ATTENTION: AFIN DE RÉDUIRE LES RISQUES

D'INCENDIE OU DE CHOC ÉLECTRIQUE, NE PAS

EXPOSER CET APPAREIL À LA PLUIE OU.

WARNING: The terminals marked with this

symbol are hazardous live. External wiring

connected to these terminals requires

installation by an instructed person or the use

of ready-made leads or cords.

ATTENTION:

RISQUE DE CHOC ÉLECTRIQUE NE PAS OUVRIR.

SAFETY INSTRUCTIONS

19XZone70V Installation Manual

point where they exit from the appliance.

Protection du cordon d'alimentation - Les cordons d'alimentation doivent être acheminés

de sorte qu'ils ne sont pas susceptibles d'être piétinés ou coincés par des objets placés sur

ou contre eux, en accordant une attention particulière aux cordons au niveau des ches,

des prises et à l'endroit où ils sortent de l'appareil.

11. Power Sources - The appliance should be connected to a power supply only of the type

described in the operating instructions or as marked on the appliance.

Sources d'énergie - Cet appareil doit être connecté à une source d'alimentation du

type décrit dans le mode manuel ou tel qu'indiqué sur l'appareil.

12. Main Power Disconnect - The power switch is a single-pole switch. When the switch is in

the “O” position, the appliance is not completely disconnected from the main power. The

main power plug is used as the disconnect device and shall remain readily operable. When

installing the product, ensure that the plug is easily accessible.

Débranchez l'alimentation principale - L'interrupteur est un interrupteur unipolaire.

Lorsque l'interrupteur est en position "O", l'appareil n'est pas complètement déconnecté

de l'alimentation principale. La che d'alimentation est utilisée comme dispositif de

déconnexion et doit rester facilement accessible. Lors de l'installation du produit, assurez-

vous que la prise soit facilement accessible.

12. Non-Use Periods - The power cord of the appliance should be unplugged from the outlet

when left unused for a long period of time.

Périodes de non-utilisation - Le cordon d'alimentation de l'appareil doit être débranché de

la prise en cas de non utilisé pendant une longue période de temps.

14. Attachments - Only use attachments/accessories specied by the manufacturer.

Accessoires - N'utilisez que des xations / accessoires spéciés par le fabricant.

15. Carts and Stands - The appliance should be used only with a cart or stand that is

recommended by the manufacturer. An appliance and cart combination

should be moved with care. Quick stops, excessive force and uneven

surfaces may cause the appliance and cart combination to overturn.

Chariots et supports - L'appareil doit être utilisé uniquement avec un

chariot ou un support recommandé par le fabricant. Une combinaison de

l'appareil et chariot doit être déplacé avec précaution. Des arrêts brusques,

une force excessive et des surfaces inégales peuvent provoquer la chute de l'appareil et du

chariot.

16. Wall or Ceiling Mounting - The appliance should be mounted to a wall or ceiling only as

recommended by the manufacturer.

Mur ou au plafond - L'appareil doit être xé au mur ou au plafond, tel que recommandé

par le fabricant.

17. Location of the Amplier - Do not mount this unit under a kitchen cabinet. Do

not expose the amplier to direct sun light or heating units as the amplier internal

components’ temperature may rise and shorten the life of the components. Avoid damp

and dusty places.

Localisation de l'amplicateur - Ne montez pas cet appareil dans une armoire de cuisine.

N'exposez pas l'amplicateur à la lumière directe du soleil ou appareils de chauage

comme la température des composants internes de l'amplicateur de risque d'augmenter

et raccourcir la durée de vie des composants. Evitez les endroits humides et poussiéreux.

18. Object and Liquid Entry - Care should be taken so that objects do not fall and liquids are

not spilled into the enclosure through the openings.

Objets et de liquides - Des précautions doivent être prises an que des objets ne tombent

ou que des liquides coulent dans le boîtier à travers les ouvertures.

19. Servicing - The user should not attempt to service the appliance beyond that described

in the operating instructions. All other servicing should be referred to qualied service

personnel.

Entretien - L'utilisateur ne doit pas tenter de réparer l'appareil au-delà de celle qui est

décrite dans le manuel d'instructions. Toutes les réparations doivent être eectuées par un

technicien qualié.

20. Damage Requiring Service - The appliance should be serviced by qualied service

personnel when: A. The power supply cord or the plug has been damaged; B. Objects have

fallen, liquid has been spilled into the appliance; C. The appliance has been exposed to

rain; or D. The appliance does not appear to operate normally; or E. The appliance has been

dropped or the enclosure is damaged.

Dommages nécessitant des réparations - L'appareil doit être réparé par un personnel

qualié lorsque: A. Le cordon d'alimentation ou la prise a été endommagé; B. Des objets

sont tombés, du liquide a été renversé dans l'appareil C. Si l'appareil a été exposé à pluie;

ou D. l'appareil ne semble pas fonctionner normalement, ou E. L'appareil est tombé ou son

boîtier est endommagé.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment o and on, the user is

encouraged to try to correct the interference by one of or more of the following measures: reorient or

relocate the receiving antenna; increase the separation between the equipment and receiver; connect

the equipment into an outlet on a circuit dierent from that to which the receiver is connected, or

consult the dealer or an experienced radio/TV technician for help.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

Laite on liitettävä suojakoskettimilla varustettuun pistorasiaan (for Finland). Apparatet må tilkoples

jordet stikkontakt (for Norway). Apparaten skall anslutas till jordat uttag (for Sweden).

Apparatets stikprop skal tilsluttes en stikkontakt med jord, som giver forbindelse til stikproppens jord

(for Denmark).

Changes or modications not expressly approved by the party responsible for compliance could void

the user's authority to operate the equipment.

SAFETY INSTRUCTIONS

Russound, Inc.

1 Forbes Road, Newmarket, NH 03857

tel 603.659.5170 • fax 603.659.5388

email: [email protected] www.russound.com

28-1404 11.09.16, Rev.2

XZone70V

Streaming Mixer Amplier

Installation Manual

AirPlay, iPad, iPhone and iPod, are trademarks of Apple Inc., registered in the U.S. and other countries. iPad Air and iPad mini are trademarks of Apple Inc.

“Made for iPhone” means that an electronic accessory has been designed to connect specically to iPhone and has been certied by the developer to meet Apple

performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. Please note that the use of this

accessory with iPhone may aect wireless performance.

SiriusXM Internet Radio Service is available in the USA, PR or Canada. SiriusXM Internet Radio subscriptions are sold separately and are governed by the Sirius Terms and

Conditions (see www.siriusxm.com). Be sure to read this agreement before you purchase your subscription. Sirius, XM and all related marks and logos are trademarks of

This product includes some software components that are licensed under the General Public License (GPL). Source code for GPL components is available upon request.