Marvel MA24BCG1LS Mode d'emploi

Marque: Marvel

Modèle: MA24BCG1LS

Catégorie: Boissons glacées

Taper: Mode d'emploi

Refrigerators

Réfrigérateurs

ML24BC

MA24BC

ML24BR

MA24BR

ML15RA

ML24RA

MA24RA

ML24WB

EN Installation, Operation and Maintenance Instructions

FR Instructions d’installation, d’utilisation et d’entretien

NOTE

CAUTION

CONTENTS

Contents:

Safety information ...............................................................2

Unpacking your appliance ..................................................3

Warranty registration .....................................................3

Installing your appliance ......................................................4

Cabinet clearances .........................................................4

Leveling the appliance ....................................................4

Electrical connection ......................................................5

Product Dimensions ...........................................................6

Using your Electronic control .............................................8

Starting your appliance ..................................................8

Sleep mode ...................................................................8

Turning your appliance "ON" or "OFF" ...........................8

Adjusting the temperature .............................................8

Interior display lighting ...................................................9

Temperature mode .........................................................9

Control lock ...................................................................10

Temperature sensor error codes .................................10

Alarms ...........................................................................10

Door ajar ...................................................................10

Power failure .............................................................11

Temperature alarm ....................................................11

Vacation mode .............................................................11

Overlay door panel installation .........................................12

Shelving congurations .....................................................19

Care and cleaning .............................................................22

Energy saving tips ............................................................22

Obtaining service .............................................................23

Troubleshooting ................................................................24

Warranty ...........................................................................25

Important Safety Instructions

Warnings and safety instructions appearing in this guide

are not meant to cover all possible conditions and situa-

tions that may occur. Common sense, caution, and care

must be exercised when installing, maintaining, or operat-

ing this appliance.

Recognize Safety Symbols,

Words, and Labels.

WARNING

WARNING-You can be killed or seriously injured if

you do not follow these instructions.

CAUTION-Hazards or unsafe practices which could re-

sult in personal injury or property / product damage.

NOTE-Important information to help assure a problem

free installation and operation.

WARNING

State of California Proposition 65 Warning:

This product contains one or more chemicals known

to the State of California to cause cancer.

WARNING

State of California Proposition 65 Warning:

This product contains one or more chemicals known

to the State of California to cause birth defects or

other reproductive harm..

NOTE

CAUTION

XXXXXXXXXXXX

UNPACKING YOUR APPLIANCE

WARNING

WARNING - Help Prevent Tragedies

Child entrapment and suffocation are not problems of

the past. Junked or abandoned refrigerators are still

dangerous - even if they sit out for "just a few hours".

If you are getting rid of your old refrigerator, please

follow the instructions below to help prevent acci-

dents.

Before you throw away your old refrigerator or

freezer:

• Take off the doors or remove the drawers.

• Leave the shelves in place so children may not

easily climb inside.

WARNING

WARNING - Dispose of the plastic bags which can

be a suffocation hazard.

Warranty Registration

It is important you send in your warranty registration card

immediately after taking delivery of your appliance or you

can register online at www.marvelrefrigeration.com.

The following information will

be required when registering

your appliance.

Service Number

Serial Number

Date of Purchase

Dealer’s name and address

The service number and serial number can be found on the

serial plate which is located inside the cabinet on the left

side near the top. (See Figure 1).

WARNING

EXCESSIVE WEIGHT HAZARD

Use two or more people to move product.

Failure to do so can result in personal injury.

Remove Interior Packaging

Your appliance has been packed for shipment with all parts

that could be damaged by movement securely fastened.

Remove internal packing materials and any tape holding in-

ternal components in place. The owners manual is shipped

inside the product in a plastic bag along with the warranty

registration card, and other accessory items.

Important

Keep your carton and packaging until your appliance has

been thoroughly inspected and found to be in good condi-

tion. If there is damage, the packaging will be needed as

proof of damage in transit. Afterwards please dispose of all

items responsibly.

Note to Customer

This merchandise was carefully packed and thoroughly

inspected before leaving our plant. Responsibility for its

safe delivery was assumed by the retailer upon acceptance

of the shipment. Claims for loss or damage sustained in

transit must be made to the retailer.

DO NOT RETURN DAMAGED MERCHANDISE TO THE

MANUFACTURER - FILE THE CLAIM WITH THE

RETAILER.

If the appliance was shipped, handled, or stored in other

than an upright position for any period of time, allow the ap-

pliance to sit upright for a period of at least 24 hours before

plugging in. This will assure oil returns to the compressor.

Plugging the appliance in immediately may cause damage

to internal parts.

Figure 1

Online registra-

tion available at

www.marvelrefrig-

eration.com

MARVEL

CAUTION

WARNING

An optional stacking kit, for 24" wide models, is re-

quired to stack products. Failure to use a stacking kit

could result in personal injury. Contact your dealer or

Marvel customer service at 800-223-3900 to order.

For safety concerns 15" wide models should not be

stacked.

Select Location

The proper location will ensure peak performance of your

appliance. We recommend a location where the unit will

be out of direct sunlight and away from heat sources. To

ensure your product performs to specications, the recom-

mended installation location temperature range is from 55

to 100°F (13 to 38°C).

Cabinet Clearance

Ventilation is required from the bottom front of the appli-

ance. Keep this area open and clear of any obstructions.

Adjacent cabinets and counter top can be installed around

the appliance as long as the front grille remains unob-

structed. Overlay door models with articulated hinges are

intended for built-in applications only.

Front Grille

Do not obstruct the front grille. The openings within the

front grille allow air to ow through the condenser heat ex-

changer. Restrictions to this air ow will result in increased

energy usage and loss of cooling capacity. For this reason

it is important this area not be obstructed and the grille

openings kept clean. Marvel does not recommend the use

of a custom made grille as air ow may be restricted. (See

Figure 2).

Front Leveling

Legs

Figure 2

Rear

Leveling

Legs

Front Grille,

keep this area

open.

INSTALLING YOUR APPLIANCE

Leveling Legs

Adjustable legs at the front and rear corners of the appli-

ance should be set so the unit is rmly positioned on the

oor and level from side to side and front to back. The over-

all height of your Marvel appliance may be adjusted higher

(by turning the leveling leg out, CCW) and lower (by turning

the leveling leg in, CW) dimensions as shown in Table A.

To adjust the leveling legs, place the appliance on a solid

surface and protect the oor beneath the legs to avoid

scratching the oor. With the assistance of another person,

lean the appliance back to access the front leveling legs.

Raise or lower the legs to the required dimension by turning

the legs. Repeat this process for the rear by tilting the appli-

ance forward using caution. On a level surface check the

appliance for levelness and adjust accordingly.

The front grille screws may be loosened and the grille ad-

justed to the desired height. When adjustment is complete

tighten the two front grille screws. (See Figure 5).

Model Door Style

Minimum

Height

Maximum

Height

ML(15)(24)* (S) or (G)

⁄4"

(85.7 cm)

⁄4"

(88.3 cm)

ML(15)(24)* (P or (F)

34"

(86.4 cm)

35"

(88.9 cm)

MA24* (S) or (G)

(79.1 cm)

⁄8"

(81.6 cm)

MA24* (P or (F)

⁄8"

(79.7 cm)

⁄8"

(82.2 cm)

Table A

NOTE

Figure 6

Electrical Shock Hazard

• Do not use an extension cord with this appliance.

They can be hazardous and can degrade product

performance.

• This appliance should not, under any circumstanc-

es, be installed to an un-grounded electrical supply.

• Do not remove the grounding prong from the power

cord. (See Figure 3).

• Do not use an adapter. (See Figure 4).

• Do not splash or spray water from a hose on the

appliance. Doing so may cause an electrical shock,

which may result in severe injury or death.

WARNING

Electrical Connection

A grounded 115 volt, 15 amp dedicated circuit is required.

This product is factory equipped with a power supply

cord that has a three-pronged, grounded plug. It must be

plugged into a mating grounding type receptacle in accor-

dance with the National Electrical Code and applicable lo-

cal codes and ordinances (see Figure 6). If the circuit does

not have a grounding type receptacle, it is the responsibility

and obligation of the customer to provide the proper power

supply. The third ground prong should not, under any cir-

cumstances, be cut or removed.

Ground Fault Circuit Interrupters (GFCI) are prone to nui-

sance tripping which will cause the appliance to shut down.

GFCI’s are generally not used on circuits with power equip-

ment that must run unattended for long periods of time, un-

less required to meet local building codes and ordinances.

Front grille screw

Front grille

Figure 5

INSTALLING YOUR APPLIANCE

Figure 3

Figure 4

Do not remove

ground prong

MODEL

ROUGH-IN OPENING DIMENSIONS CABINET DIMENSIONS

"A" "B" "C" "D" "E" "F" "G" "H" "J"

ML15**(G) or (S)

15"

(38.1 cm)

**34" to 35"

(86.4 to 88.9 cm)

24"

(61 cm)

⁄8"

(37.8 cm)

⁄4" to 34

⁄4"

(85.7 to 88.3 cm)

⁄32"

(60.2 cm)

⁄32"

(65.2 cm)

⁄32"

(95 cm)

⁄16"

(42.4 cm)

ML15**(P) or (F)

15"

(38.1 cm)

**34

⁄4" to 35

⁄4"

(87 to 89.5 cm)

* 24"

(61 cm)

⁄8"

(37.8 cm)

34" to 35"

(86.4 to 88.9 cm)

⁄8"

(58.1 cm)

⁄2"

(95.2 cm)

⁄8"

35.9 cm)

ML24**(G) or (S)

24"

(61 cm)

**34" to 35"

(86.4 to 88.9 cm)

24"

(61 cm)

⁄8"

(60.7 cm)

⁄4" to 34

⁄4"

(85.7 to 88.3 cm)

⁄32"

(60.2 cm)

⁄32"

(65.2 cm)

⁄32"

(117.9 cm)

⁄16"

(65.2 cm)

ML24**(P) or (F)

24"

(61 cm)

**34

⁄4" to 35

⁄4"

(87 to 89.5 cm)

* 24"

(61 cm)

⁄8"

(60.7 cm)

34" to 35"

(86.4 to 88.9 cm)

⁄8"

(58.1 cm)

⁄2"

(118.1 cm)

⁄8"

(58.7 cm)

MA24**(G) or (S)

24"

(61 cm)

** 31

⁄8" to 32

⁄8"

(79.7 to 82.2 cm)

24"

(61 cm)

⁄8"

(60.7 cm)

⁄8" to 32

⁄8"

(79.1 to 81.6 cm)

⁄32"

(60.2 cm)

⁄32"

(65.2 cm)

⁄32"

(117.9 cm)

⁄16"

(65.2 cm)

MA24**(P) or (F)

24"

(61 cm)

** 31

⁄8" to 32

⁄8"

(80.3 to 82.9)

* 24"

(61 cm)

⁄8"

(60.7 cm)

⁄8" to 32

⁄8"

(79.7 to 82.2 cm)

⁄8"

(58.1 cm)

⁄2"

(118.1 cm)

⁄8"

(58.7 cm)

DOOR STYLE

(G) Glass Frame Door

(S) Solid Door

(P) Solid Overlay Door (no handle)

(F) Frame Glass Overlay Door (no handle)

"A"

"B"

"C"

"D"

"E"

If necessary to gain clearance inside the rough-in

opening a hole can be cut through the adjacent cabi-

net and the power cord routed through this hole to a

power outlet. Another way to increase the available

opening depth is to recess the power outlet into the

rear wall to gain the thickness of the power cord plug.

Not all recessed outlet boxes will work for this applica-

tion as they are too narrow, but a recessed outlet box

equivalent to Arlington #DVFR1W is recommended for

this application, (see Figure 8).

PRODUCT DIMENSIONS

Figure 7

(S) Solid door shown

Figure 7a

Figure 8

"F"

⁄2"

(54.6 cm)

* To install (F) and (P) models with the door face ush with

adjacent cabinetry doors, custom decorative panel thick-

ness cannot exceed

⁄4" (19 mm).

** Minimum rough-in opening required is to be larger than

the adjusted height of the cabinet.

# A grounded 15 amp dedicated circuit is required. Follow

all local building codes when installing electrical and appli-

ance.

APPLIES TO THE FOLLOWING MARVEL MODELS

ML15BC MA24BC

ML15RA MA24BR

MA24RA

ML24BC

ML24BR

ML24RA

ML24WB

MODEL

PRODUCT DATA

ELECTRICAL

REQUIREMENTS #

PRODUCT

WEIGHT

ML15**(G) or (S) 115V/60Hz/15A

105 lbs

(47.7 kg)

ML15**(P) or (F) 115V/60Hz/15A

105 lbs

(47.7 kg)

ML24**(G) or (S) 115V/60Hz/15A

140 lbs

(63.6 kg)

ML24**(P) or (F) 115V/60Hz/15A

140 lbs

(63.6 kg)

MA24**(G) or (S) 115V/60Hz/15A

140 lbs

(63.6 kg)

MA24**(P) or (F) 115V/60Hz/15A

140 lbs

((63.6 kg)

"D"

"E"

"H"

"J"

"G"

PRODUCT DIMENSIONS

Figure 9

(S) Solid door shown

USING YOUR ELECTRONIC CONTROL

NOTE

Power Failure

ALARM RESET

Upper/Lower

zones

(Dual Zone

models only)

Turning your appliance ON and OFF (Single

and Dual Zone):

If the appliance is "On", (and out of sleep mode) the tem-

perature will be shown in the display area of the control.

To turn the appliance "Off", press and hold the "On/Off"

keypad for 4-seconds. "OFF" will now be displayed on the

control.

To turn the appliance "On", press and hold the "On/Off"

keypad for 4-seconds.

The sleep mode can be disabled if you prefer to have the

display on continuously. Press and hold the "Lock" key-

pad until the display goes past "Loc" and reads "nSL". To

enable the sleep mode, repeat the instruction, again going

past "Loc" until the display reads "SLP".

To wake the display press any keypad. A conrm tone will

sound, and the current storage compartment temperature

will be displayed.

Sleep mode (Single and Dual Zone):

If no keypads are pressed for 60 seconds, the display will

enter sleep mode to conserve power. The control panel will

go dark with the exception of the system status "OK" indi-

cator which will remain enabled. Alarm conditions will wake

the display, (see alarms on page 10).

To make the following changes to the control settings

(turning the appliance ON/OFF, adjusting the tempera-

ture, changing the interior lights, and activating vaca-

tion mode), the control must be awake.

Starting your appliance (Single and Dual

Zone:

Plug the appliance power cord into a 115 volt wall outlet.

Your appliance is shipped from the factory in the "On" posi-

tion and will begin start-up of cooling as soon as power is

supplied. If the appliance does not start, conrm that the

wall outlet has power, and that the control is in the "On"

position, (See "Turning your appliance On and Off" below).

The control display is covered with a clear plastic lm. This

lm may be removed by carefully lifting the lm at a corner.

On initial power up, the control display will indicate a

"Power Failure" alarm. This is a normal condition as the ap-

pliance was powered-up at the factory for quality inspection

and then removed from power. A momentary press of the

"On/Off" keypad will reset this alarm condition. (See Alarms

section on page 10).

Figure 10

Electronic control

Temp

Minus

keypad

Temp

Plus

keypad

On/Off

keypad

Display Area

Lights keypad

(glass door

only)

Lock

keypad

System Status

indicators

Adjusting the temperature:

When initially loading your product with warm contents, it

may take up to 48-hours for the storage compartment tem-

perature to stabilize.

When making temperature set-point changes, it may take

up to 24-hours for the stored contents to stabilize at your

new set-point temperature.

USING YOUR ELECTRONIC CONTROL

Single Zone Models:

To set or check the set-point temperature (with the control

out of sleep mode), press the "-" or "+" keypads. "SET" will

be indicated on the user interface panel and the current

set-point temperature will display and ash. Subsequent

presses of the "-" or "+" keypads will adjust the temperature

colder or warmer respectively. When you have reached

your desired set-point temperature, press the "On/Off" key-

pad to accept, or do nothing and the "Set" mode will time-

out in 10-seconds accepting the displayed temperature as

the new set-point.

The available set-point temperature range for your ap-

pliance is 34°F (1.2°C) to 42°F (5.7°C). If you attempt to

adjust the temperature outside of this range you will receive

an audible notication.

To change the set temperature for a particular zone, with

the zone selected and out of sleep mode, press the "-" or

"+" keypads. "SET" will be indicated on the user interface

panel and the current set-point temperature will display

and ash. Subsequent presses of the "-" or "+" keypads

will adjust the temperature colder or warmer respectively.

When you have reached your desired set-point tempera-

ture, press the "On/Off" keypad to accept, or do nothing

and the "Set" mode will time-out in 10-seconds accepting

the displayed temperature as the new set-point.

The available set-point temperature range for your appli-

ance is 34°F (1.2°C) to 42°F (5.7°C) for the lower zone

and 45°F (7°C) to 60°F (16°C) for the upper zone. If you

attempt to adjust the temperature outside of these ranges

you will receive an audible notication.

Lower zone

selected

Upper zone

selected

Dual Zone Models:

Temperatures can be set for each individual zone (upper

and lower) in the dual zone wine / beverage center. To

do so you must rst select the zone you want to set the

temperature for. You do so by pressing the upper or lower

button on the display. When pressed the LED light will be

illuminated for the respective display.

Interior display lighting (Single and Dual

Zone): (Glass door models only)

Your appliance is equipped with a dual light level display

lighting feature. With the control out of sleep mode press

the "Light" keypad once to activate the interior lighting

display feature at full illumination. A conrmation tone will

sound, and the light bulb "Icon" will illuminate. Pressing

the "Light" keypad a 2nd time will dim the lighting to 50%.

A 3rd press will deactivate the display lighting feature. The

display lighting will automatically deactivate after 4-hours.

Factors that affect the storage compartment stabilized

temperature:

• Changes to temperature setting.

• Room temperature changes.

• Temperature of stored contents.

- Loading warm contents.

- Cold content load will delay the change to a warmer

set-point temperature.

- Warm content load will delay the change to a colder

set-point temperature.

• Usage, (number and duration of the door openings).

• Use of the storage compartment display lighting, (glass

door product only).

• Installation of the appliance in direct sunlight or next to

a heat source.

Temperature mode (Single and Dual Zone):

The temperature mode is preset from the factory in Fahren-

heit (°F) but you have the option to change it to Centigrade

(°C). To change the mode, press and hold the "-" keypad,

while pressing the "+" keypad, then release the "-" keypad.

The temperature will now be displayed in Centigrade (°C).

Repeat the procedure to change the temperature mode

back to Fahrenheit (°F).

NOTE

The upper zone is designed exclusively for the storage of

wine. The upper zone cannot attain storage temperatures

suitable for fresh food storage.

USING YOUR ELECTRONIC CONTROL

Door Ajar

ALARM RESET

NOTE

If the control lock is active (illuminated lock icon) the control

will have to be unlocked before using the keypad to reset

an alarm condition. See page 10 (Control Lock) for instruc-

tions for unlocking the control.

Control lock:

The control panel can be locked to avoid unintentional

changes. To lock the control, press and hold the "Lock" key-

pad until the display reads "Loc" then immediately release

your nger from the keypad. The lock icon will ash 3-times

and then continuously illuminate. When the control panel is

locked, only the Lock keypad, System Status OK indicator

, and the Alarm indicator are active. To un-lock the control

panel, repeat this instruction until the display reads "nLc",

then immediately release your nger from the keypad.

The temperature sensors are monitored continuously. Any

OPEN or SHORTED circuit condition will initiate an

ERROR CODE as listed below:

Temperature Sensor Error Codes

Sensor Displayed Code Error Description Action to Take

Single Zone

Temperature Sensor

Failed temperature sensor in the single

zone compartment. Can lead to unwant-

ed wine storage temperatures.

Call service to have the tem-

perature sensor replaced.

Defrost Sensor

Failed defrost temperature sensor.

Causes unit to not defrost properly and

can create large frost build-up. Can lead

to water damage to the unit and sur-

rounding oor.

Unplug the power cord imme-

diately and call service to have

the defrost sensor replaced.

Single Zone Models:

Dual Zone Models:

Temperature Sensor Error Codes

Sensor Displayed Code Error Description Action to Take

Upper Zone

Temperature Sensor

Failed temperature sensor in the upper

zone compartment. Can lead to unwant-

ed wine storage temperatures.

Call service to have the tem-

perature sensor replaced.

Lower Zone

Temperature Sensor

Failed temperature sensor in the lower

zone compartment. Can lead to unwant-

ed wine storage temperatures.

Call service to have the tem-

perature sensor replaced.

Defrost Sensor

Failed defrost temperature sensor.

Causes unit to not defrost properly and

can create large frost build-up. Can lead

to water damage to the unit and sur-

rounding oor.

Unplug the power cord imme-

diately and call service to have

the defrost sensor replaced.

Temperature Sensor Error Codes

This alarm condition can be reset by closing the door or

momentarily pressing the "On/Off" keypad, (i.e.-if you

are cleaning the storage compartment, etc.). The alarm

will recur in 5-minutes if the alarm condition persists.

Alarms (Single and Dual Zone):

The control will alert you to conditions that could adversely

affect the performance of the appliance.

• Door ajar - If the door is open, or not closed prop-

erly, for more than 5-minutes the System Status OK

indicator will turn-off, the "Door Ajar" indicator will ash,

and a tone will sound every 60 seconds. Additionally,

an "ALARM RESET" indicator will be displayed below

the "On/Off" keypad.

NOTE

The audible alarm can be muted, for each occurrence,

by pressing the lock keypad.

USING YOUR ELECTRONIC CONTROL

ALARM RESET

Power Failure

ALARM RESET

Temp

NOTE

Door Ajar

Temp

• Power failure - If power to the appliance is inter-

rupted the System Status indicator will turn-off and

the "Power Failure" indicator will ash. Additionally, an

"ALARM RESET" indicator will be displayed below the

"On/Off" keypad. No audible tone will sound. This alarm

condition can be reset by momentarily pressing the

"On/Off" keypad. If this alarm occurs, it is recommend-

ed that you check the condition of any perishables,

even if the appliance is operating normally and the tem-

perature has recovered, as prolonged power outages

could result in excessive temperature excursions which

may spoil perishables.

• Temperature alarm - If the storage compart-

ment temperature deviates excessively from your

set-point temperature for an extended period of time,

the "TEMP" indicator will ash, and an audible tone

will sound every 60 seconds. Additionally, an "ALARM

RESET" indicator will be displayed below the "ON/

OFF" keypad.

Multiple alarms are possible, i.e.- "Door Ajar" for a pro-

longed period may trigger a "Temp" alarm, in which case

both "Door Ajar" and "Temp" indicators will activate.

Vacation mode (Single and Dual Zone):

This operating mode can be used to save energy during

high cost energy periods, or when you won't be using your

appliance for an extended period of time by disabling the

lights, alarm tones, and keypad entry tones. Vacation mode

also serves as a Sabbath mode, disabling functions and

its controls in accordance with the weekly Sabbath and

religious holidays observed within the Orthodox Jewish

community. When used as Sabbath mode, you may open

or close the door at any time to access contents without

concern of directly turning on or off any lights, digital read-

outs, solenoids, fans, valves, compressor, icons, tones, or

alarms.

When activated, the display, alarm indicators and tones,

keypad touch tones, interior lights, and all options are dis-

abled. All keypad functions are disabled, with the exception

of the "On/Off" keypad which is required to exit Vacation-

mode. Storage compartment temperatures are monitored

and controlled at the settings prior to entering Vacation

mode.

To enter Vacation Mode (with the control out of sleep

mode), press and hold the "On/Off" keypad until the display

goes past "OFF" and reads "VAC". The display will ash

"VAC" 3-times to acknowledge your request, then will

display "VAC" continuously until Vacation mode is exited.

A power outage will not exit Vacation mode, exiting can

only be accomplished manually. To exit Vacation mode and

return to normal operation, press and hold the "On/Off"

keypad until the control displays the temperature.

NOTE

The audible alarm can be muted, for each occurrence, by

pressing the lock keypad.

This alarm condition can be reset by momentarily pressing

the "On/Off" keypad. If this alarm occurs it is recommended

that you check the condition of your stored contents, even

though the appliance is operating normally and the temper-

ature has recovered, as prolonged temperature excursions

could spoil perishables.

NOTE

After a high temperature alarm condition, check all perish-

ables to ensure they are safe for consumption.

The temperature alarm may occur as a result of high usage

or introduction of warm contents to the storage compart-

ment. If the temperature alarm continues to occur, your unit

may require service.

OVERLAY DOOR PANEL INSTALLATION

WARNING

Overlay panel models are designed for use with built-

in installations only. Use in freestanding installations

could result in personal injury.

WARNING

The articulated hinges have many pinch points. Care-

fully close / collapse the hinges as soon as the door is

removed from the cabinet.

If you purchased an overlay panel model, your unit is

equipped with articulated hinges to allow fully integrated

built-in installations. Custom panel thicknesses of

⁄8" (15

mm) and

⁄4" (18 mm) are accommodated.

Figure 11

Figure 11b

Bottom of

door

Figure 11a

Loosen (do not remove ) these

2 phillips head screws on the

top and bottom hinges

Step 1: Removing the Door

With a phillips screwdriver remove the screw and "P" clamp

from the bottom of the door near the hinge. See Figure 11b.

Disconnect the door wire harness by pressing and holding

down the locking tab on the wire connector and pulling the

connector apart. See Figure 12.

Open the door and loosen the screws holding the hinges to

the cabinet (2 at the top and 2 at the bottom hinge). Do not

remove the screws but loosen them enough so the hinges

can be slipped off of the screws when sliding the door to

the side.

With a helper, and being careful not to scratch the cabinet

or the door, slide the door to the side about

⁄2 inch and

remove the hinges and door from the unit.

"P" clamp

and screw

Wire connector

see Figure 12

Cabinet

"Z" Bracket

WARNING

Use extreme caution with the articulated hinges. The

hinge is self closing and many pinch points exist prior

to built-in installation. Do not remove the cabinet "Z"

bracket from the top of the cabinet.

CAUTION

It is important to use the factory provided grille that came

with the product to assure proper air ow is maintained

through the condenser. The use of a custom grille is not

recommended and will void the warranty.

Step 2: Remove the door gasket

With the door laying on a at surface and starting at a

corner of the door remove the magnetic door gasket from

the interior side of the door, see Figure 13. Set the gasket

aside on a at surface.

There are 10 holes in the gasket retainer extrusions, (3 on

each side and 2 at the top and bottom which are used to

fasten the panel to the front of the door. The screws are

provided in the literature pack along with the door lock,

which is provided on certain models.

Figure 12

Press and hold down this

tab on the wire connec-

tor and pull the connector

apart.

Figure 13

Figure 13a

Overlay panel

ush with top

of door.

Holes in

gasket

retainer.

Magnetic Gasket

remove starting at a

corner, grasp and pull

away from the door.

OVERLAY DOOR PANEL INSTALLATION

Step 3: Cut and drill the overlay panel

Depending on your model cut the overlay door panel to the

dimensions shown in Figure 14 to Figure 21. Also see Table

C for the height dimension and door styles. The window cut

out is for glass door models only. If your appliance has a

lock also drill the lock hole in the panel, see Figure 23.

Overlay panel to

be centered on

width of door.

Clearance for

screw head,

4 places

Clearance

for hinge

2 places

Figure 16

Right Hand Hinged Door

15" (38.1 cm) wide appliance

OVERLAY DOOR PANEL INSTALLATION

Figure 17

Right Hand Hinged Door

15" (38.1 cm) wide appliance

Clearance for

screw head,

4 places

Clearance

for hinge

2 places

Figure 14

Left Hand Hinged Door

15" (38.1 cm) wide appliance

Figure 15

Left Hand Hinged Door

15" (38.1 cm) Wide Appliance

⁄8"

(12.4 cm)

⁄32"

(9.8 cm)

⁄16"

(3 cm)

⁄8"

(7.9 cm)

⁄2"

(3.8 cm)

typical

Hinge side of door

Top of door

⁄4"

(37.5 cm)

⁄4" (6 mm)

Deep

(12.7 cm)

1" (25.4 mm) diameter

counter bore

⁄4" (6 mm)

deep 4 places.

⁄4"

(4.4 cm)

"A"

(See Table C)

⁄8"

(7.9 cm)

Minimum

(5.1 cm)

⁄16"

(9.4 cm)

⁄8"

(10.5 cm)

Minimum

⁄8"

(7.9 cm)

Minimum

⁄4" (6 mm)

radius is

permissible

⁄16"

(4.3 cm)

⁄8"

(12.4 cm)

⁄32"

(9.8 cm)

⁄16"

(3 cm)

⁄8"

(7.9 cm)

⁄2"

(3.8 cm)

typical

⁄16"

(4.3 cm)

Hinge side of door

⁄4"

(37.5 cm)

⁄4" (6 mm)

Deep

(12.7 cm)

1" (25.4 mm) diameter

counter bore

⁄4" (6 mm)

deep 4 places.

⁄4"

(4.4 cm)

"A"

(See Table C)

⁄8"

(7.9 cm)

Minimum

(5.1 cm)

⁄16"

(9.4 cm)

⁄8"

(10.5 cm)

Minimum

⁄8"

(7.9 cm)

Minimum

This side

facing interior

This side

facing interior

⁄4" (6 mm)

radius is

permissible

⁄32"

(2.9 cm)

⁄32"

(2.9 cm)

Figure 19

Left Hand Hinged Door

24" (61 cm) wide appliance

CAUTION

OVERLAY DOOR PANEL INSTALLATION

Weight of overlay door panel must not

exceed 15 pounds (6.8 kg) for a solid

door model or 10 pounds (4.5 kg) for a

glass door model.

Figure 21

Right Hand Hinged Door

24" (61 cm) wide appliance

⁄4"

(60.3 cm)

1" (2.5 cm) diameter

⁄4" (6 mm) deep

4 places

⁄8"

(12.4 cm)

⁄32"

(9.8 cm)

⁄16"

(3 cm)

14"

(35.6 cm)

⁄4" (6 mm)

radius is

permissible

⁄8"

(7.9 cm)

⁄4"

(4.4 cm)

⁄8"

(7.9 cm)

⁄8"

(7.9 cm)

"A"

(See Table C)

(5.1 cm)

⁄16"

(9.4 cm)

⁄8"

(10.5 cm)

⁄2"

(3.8 cm)

typical

⁄4"

(6 mm)

Deep

⁄16"

(4.3 cm)

Hinge side of door

Top of door

Clearance for hinge

at top and bottom

Clearance for hinge

at top and bottom

Clearance for

screw head,

4 places

Figure 18

Left Hand Hinged Door

24" (61 cm) wide appliance

⁄4"

(60.3 cm)

1" (2.5 cm) diameter

⁄4" (6 mm) deep

4 places

⁄8"

(12.4 cm)

⁄32"

(9.8 cm)

⁄16"

(3 cm)

14"

(35.6 cm)

⁄4" (6 mm)

radius is

permissible

⁄8"

(7.9 cm)

⁄8"

(7.9 cm)

⁄8"

(7.9 cm)

⁄4"

(4.4 cm)

"A"

(See Table C)

(5.1 cm)

⁄16"

(9.4 cm)

⁄8"

(10.5 cm)

⁄2"

(3.8 cm)

typical

⁄4"

(6 mm)

Deep

⁄16"

(4.3 cm)

Hinge side of door

Top of door

Clearance for

screw head,

4 places

Figure 20

Right Hand Hinged Door

24" (61 cm) wide appliance

This side

facing interior

This side

facing interior

⁄32"

(2.9 cm)

⁄32"

(2.9 cm)

OVERLAY DOOR PANEL INSTALLATION

Step 4: Assemble the panel to the door

The preferred method of attaching the panel to the door

is to clamp the panel to the door so it cannot move while

drilling the screw pilot holes. Use bar clamps or "C" clamps

with pads on the clamping surfaces that will not mar the

panel or the door. The custom overlay panel should be

ush with the top of the door and centered along the width

of the door. See Figure 13a. Drill holes through the gasket

extrusion using the 10 holes as pilot holes. Use the drill

size from the chart in Table B, being careful not to drill

through the front surface of the panel. If the overlay panel is

thinner than

⁄8" (16 mm) thick shorter screws will have to be

obtained. Fasten the panel to the door with the 10 screws

provided in the literature pack. (See Figure 23a). Remove

the clamps and replace the gasket in the gasket extrusion

channels of the door. Some force may be required to seat

the gasket into the channels. Be sure the gasket corners

are seated properly.

MODEL

DOOR

DESCRIPTION DIM "A"

ML15RAP*RP Solid, Right Hand

⁄32" (77.1 cm)

ML15RAP*LP Solid, Left Hand

ML15BCF*RP Glass, Right Hand

ML15BCF*LP Glass, Left Hand

ML15BCP*RP Solid, Right Hand

ML15BCP*LP Solid, Left Hand

ML24RAP*RP Solid, Right Hand

ML24RAP*LP Solid, Left Hand

ML24BCF*RP Glass, Right Hand

ML24BCF*LP Glass, Left Hand

ML24BCP*RP Solid, Right Hand

ML24BCP*LP Solid, Left Hand

ML24BRF*RP Glass, Right Hand

ML24BRF*LP Glass, Left Hand

ML24BRP*RP Solid, Right Hand

ML24BRP*LP Solid, Left Hand

ML24WBF*RP Glass, Right Hand

ML24WBF*LP Glass, Left Hand

ML24WBP*RP Solid, Right Hand

ML24WBP*LP Solid, Left Hand

MA24BRF*RP

Glass, Right Hand

with Lock

⁄32" (70.4 cm)

MA24BRF*LP

Glass, Left Hand

with Lock

MA24RAP*RP

Solid, Right Hand

with Lock

MA24RAP*LP

Solid, Left Hand

with Lock

Table B

Table C

Material Type #10 Wood Screw

Hardwood

⁄8" (3.2 mm) Diameter. Pilot Hole

Softwood

⁄64 (2.8 mm) Diameter. Pilot Hole

Step 5: Assemble lock parts

Two (2) lock extensions are provided with the lock. Use

the longer extension for

⁄4" thick overlay panels and the

shorter one for

⁄8" thick overlay panels. Assemble the lock

extension, cam stop washer, spring washer, and set screw

to the lock as shown in Figure 22 and Figure 24.

Install this lock assembly into the lock hole in the overlay

panel and secure with the retaining nut on the back side

with a 15 mm socket and ratchet. Make sure the key slot in

the front of the lock is vertical.

OVERLAY DOOR PANEL INSTALLATION

⁄32"

(13.7 mm)

/2"

(89 mm)

⁄2" (13 mm) diameter drill

through door panel, from

other side (see detail

above)

⁄16" (20.5 mm)

counter bore,

⁄16" (11 mm)

deep.

Hinge side of door

Counter bore

lock hole

on back side.

Step 6: Install lock cam

Attach the lock cam to the back of the lock assembly with

the phillips head screw provided. Orient the lock cam verti-

cally when installing on the lock.

SECTION A-A

SCALE 1 : 1

LOCK

NUT

BRASS EXTENSION

CAM

PHILLIPS SCREW

13/16 COUNTER

BORE 7/16 DEEP

1/2 HOLE

3/4 INCH

WOOD PANEL

SPRING WASHER

INNER

DOOR

Figure 22

Figure 23a

#10 x 1/2"

screw

Figure 23

OVERLAY DOOR PANEL INSTALLATION

Step 8: Secure the cabinet

Use the #8 x

⁄4" black screws from the literature pack to

secure the counter top to the cabinet top through the holes

in the cabinet "Z" bracket.

Cabinet

"Z" bracket

#8 x

⁄4" black

screws

(3 places)

Figure 25

Step 7: Install the door

Carefully open the top and bottom hinges on the door being

careful as there are many pinch points. Place the hinges

over the 4 screws in the cabinet, 2 at the top and 2 at the

bottom and slide the door into position. Tighten the 4 hinge

screws with a phillips screwdriver. (See Figure 11 and

Figure 11a). Place wire harness from the grille and mount

to the bottom of the door with the screw and "P" clamp

removed in step 1. (See Figure 11b). Reconnect the wire

harness, (See Figure 12).

Figure 24

Cam stop

washer

Spring

washer

Cam

Set screw

Lock

Key

Retainer

nut

Screw

Brass extension

(2 lengths provided

Figure 26

Figure 27

Figure 29

Figure 30

Figure 31

SHELVING CONFIGURATIONS

Beverage Center:

Dual Zone Wine / Beverage Center:

Beverage Refrigerator:

Refrigerator:

Loading Tips and Suggestions

Your appliance is equipped with a cantilever shelf system

which provides maximum adjust ability and customizing of

the shelving arrangements listed below.

15" (38.1 cm) Wide Models:

Shown with a glass door. Figure 26.

15" (38.1 cm) Wide Models:

Shown with a solid door. Figure 30.

24" (61 cm) Wide Models:

Shown with a glass door. Figure 27.

24" (61 cm) Wide Models:

Shown with a glass door. Figure 28.

24" (61 cm) Wide Models:

Shown with a glass door. Figure 29.

(2) wine cutout and at

glass cantilever shelf.

(See Figure 36).

(1) half depth roll-out

4 bottle wine shelf.

(2) frame and at glass cantile-

ver shelves. (See Figure 35).

(1) half width at glass can-

tilever shelf. (See Figure 34).

(1) wine cutout and at glass

cantilever shelf. (See Figure 36).

(1) frame and at glass crisper

cover.

(1) roll-out crisper pan

(2) frame and at glass cantile-

ver shelves. (See Figure 35).

24" (61 cm) Wide Models:

Shown with a solid door. Figure 31.

(2) perforated metal

cantilever shelves.

(See Figure 33).

Upper Zone:

(2) pull-out wire

wine shelf. (See

Figure 37).

Lower Zone:

(1) wine cutout

and at glass shelf.

(See Figure 36).

Figure 28

NOTE

The upper zone is designed exclusively for the storage of

wine. The upper zone cannot attain storage temperatures

suitable for fresh food storage.

To remove the crisper :

Pull out until it stops. Lift up on the

front of the pan, and remove it from

the frame.

Figure 35

Frame and at glass shelf

Half width shelf shown

Figure 34

Frame and at glass shelf

Half width shelf shown

Wine shelf

underneath glass

Figure 33

Perforated metal shelf

Figure 36

Wine cutout and at glass shelf with

vibration dampening mat,

all or part of the glass can be

removed to increase or decrease

wine storage and beverage areas.

Door storage racks

Tall bottle

storage area

SHELVING CONFIGURATIONS

Figure 37

Pull-out wire

wine shelf

Figure 38

Figure 32

Refrigerator:

24" (61 cm) Wide Models:

Shown with a solid door with door racks. Figure 32.

(1) half width at glass

cantilever shelf. (See

Figure 35).

(1) frame and

slumped glass

cantilever shelf.

(1) frame and at

glass crisper cover.

(1) roll-out crisper pan.

(1) full width door

storage rack.

(1) half width door

storage rack.

La page charge ...

Marvel MA24BCG1LS Mode d'emploi

Marque: Marvel

Modèle: MA24BCG1LS

Catégorie: Boissons glacées

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Marvel MA24BCG1LS Operating instructions

Marvel MA24BCG1LS Mode d'emploi

Marvel MA24BCG1LS Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents