Astria Montebello DLX Mode d'emploi

Marque: Astria

Modèle: Montebello DLX

Catégorie: Cheminées

Taper: Mode d'emploi

Ce manuel convient également à

Montebello DLXCD

- Do not store or use gasoline or other ﬂammable

vapors and liquids in the vicinity of this or any

other appliance.

- WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use

any phone in your building.

• Leave the building immediately.

• Immediately call your gas supplier from a neigh-

bor’s phone. Follow the gas supplier’s instruc-

tions.

• If you cannot reach your gas supplier, call the

ﬁre department.

- Installation and service must be performed by

a qualiﬁed installer, service agency or the gas

supplier.

WARNING:

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could

result in serious injury, death, or property damage.

AVERTISSEMENT:

RISQUED’INDENDIE OU D’EXPLOSION

Le non-respect Des avertissements de sécurité

pourrait d’entraîner des blessures graves, la mort

ou des dommages matériels.

- Ne pas entreposer ni utilizer d’essence ni d’autres

vapeurs ou liquides inﬂammables dans le voisinage

de cet appareil ou de tout autre appareil.

- QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:

• Ne pas tenter d’allumer d’appareil.

• Ne touchez à aucan interrupteur. Ne pas vous servir

des téléphones se trouvant dans le bâtiment où

vous trouvez.

• Sortez immédiatement de bâtiment.

• Appelez immédiatement votre fournisseur de

gaz depuis un voisin. Suivez les instructions du

fournisseur.

• Si vous ne pouvez rejoindre le fournisseur de gaz,

appelez le service des incindies.

- L’installation et l’entretien doivent être assurés par

un installateur ou un service d’entretien qualiﬁé

ou par le fournisseur de gaz.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future

reference.

Installateur : Laissez cette notice avec l’appareil.

Consommateur : Conservez cette notice pour

consultation ultérieure.

This appliance may be installed in an aftermarket permanently located, manufactured home (USA only) or

mobile home, where not prohibited by local codes. This appliance is only for use with the type of gas indicated

on the rating plate. This appliance is not convertible for use with other gases, unless a certiﬁed kit is used.

Cet appareil peut installé dans une maison préfabriquée (mobile) déjà installée à demeure, si les réglements

locaux le permettent. Ce appareil doit être utilisé uniquement avec le type de gaz indiqué sure la plaque

signalétique. Cet appareil ne peut être converti à d’autres gaz, sauf si une trousse de conversion est utilsée.

Installation and Operation Instructions

Models

PFS

USC

Report No. F14-106

Ce manuel est disponible en francais, simplement

en faire la demande. Numéro de la pièce 900343-02

P/N 900343-00 Rev. J 07/2023

Montebello® DLX 40 and 45 in. Direct Vent Gas Fireplaces

P900343-00

MontebelloDLX40TEN

MontebelloDLXCD40TEN

MontebelloDLX40TEP *

MontebelloDLXCD40TEP *

MontebelloDLX45TEN

MontebelloDLXCD45TEN

MontebelloDLX45TEP *

MontebelloDLXCD45TEP *

* If ﬁeld converted to LP gas.

DANGER

HOT GLASS WILL

CAUSE BURNS.

DO NOT TOUCH GLASS

UNTIL COOLED.

NEVER ALLOW CHILDREN

TO TOUCH GLASS.

A barrier designed to reduce the risk of burns from the hot viewing glass is pro-

vided with this appliance and shall be installed for the protection of children and

other at-risk individuals.

DANGER

PELIGRO

VITRE CHAUDE

RISQUE DE BRÛLURES.

NE TOUCHEZ PAS UNE VITRE

NON REFROIDIE.

NE LAISSEZ JAMAIS UN ENFANT

DE TOUCHER LA VITRE.

EL VIDRIO CALIENTE

CAUSARÁ QUEMADURAS.

USTED DEBE NUNCA

TOCAR EL VIDRIO CALIENTE.

LOS NIÑOS DEBEN NUNCA

TOCAR EL VIDRIO.

L’écran pare-étincelles fourni avec ce foyer réduit le risque de brûlure en cas de

contact accidentel avec la vitre chaude et doit être installé pour la protection Des

enfants et Des personnes à risques.

Una barrera diseñada para reducir el riesgo de quemaduras desde la mirilla (vidrio)

caliente es proveida con este aparato y deberá instalarse para la protección de los

niños y otros individuos en riesgo.

Vea el volante adjunto para la representación de color adecuado

See attached color ﬂyer for proper color representation

Voir ci-joint tract pour une bonne représentation de la couleur

SAFETY AND YOUR FIREPLACE

General Information

900343-00J, 07/2023

Innovative Hearth Products

Montebello® DLX Series Direct-Vent Gas Fireplaces

General Information

900343-00J, 07/2023

Innovative Hearth Products

Montebello® DLX Series Direct-Vent Gas Fireplaces

 Aﬁn d’éviter les brûlures

graves ou les blessures,

ne pas retirer l’écran de

protection de la foyer qui

empêche tout contact

direct avec la vitre.

 Suivez les instructions de sécurité

ci-dessous et veillez à ce que tous

les membres de votre famille soient

conscients du danger de brûlure

encouru :

• Les surfaces de votre foyer deviennent

EXTRÊMEMENT CHAUDES !

• La vitre située à l'avant du foyer atteint

des températures EXTRÊMEMENT

ÉLEVÉES et peut causer de graves

blessures en cas de contact.

• Tenez les enfants à l'écart du foyer

lorsqu'il fonctionne. Surveillez

attentivement les enfants dans les

pièces où un foyer est utilisé aﬁn

d'éviter qu'ils ne soient en contact avec

la vitre.

• Tenez tous les vêtements, les meubles,

l'essence et tout autre liquide

inﬂammable à l'écart du foyer.

• Même après fermeture du gaz, les

surfaces du foyer restent extrêmement

chaudes.

 Veillez à coller les Étiquettes de mise

en garde relatives à la sécurité

d'utilisation à l'endroit où vous

utilisez le foyer, pour rappeler à tous

les utilisateurs les dangers liés aux

températures élevées

(Page 35)



Lisez L’information de sûreté

importante (Page 34)

Para evitar quemaduras y lesiones

graves, no quite el protector de malla

o guardia de seguridad que evita el

contacto directo con el vidrio.

 Siga las instrucciones de seguridad

a continuación y asegúrese de que

todos en su hogar sepan acerca de este

peligro de quemadura:

• ¡Las superﬁcies de la chimenea

estarán EXTREMADAMANTE

CALIENTES!!

• El vidrio delante de la

chimenea alcanza temperaturas

EXTREMADAMENTE ALTAS y puede

causar quemaduras graves si se toca.

• Mantenga a los niños alejados de

la chimenea en funcionamiento.

Supervise en forma cercana a los niños

en cualquier cuarto donde haya una

chimenea funcionando para impedir el

contacto con el vidrio.

• Mantenga la ropa, mobiliario, gasolina

y otros líquidos inﬂamables alejados

de la chimenea.

• Aún después de haber apagado el

gas, las superﬁcies de la chimenea

permanecen extremadamente

calientes.

 Asegúrese de colocar las Etiquetas de

advertencia de seguridad de operación

en el lugar donde enciende la chimenea,

para que todos recuerden los peligros

asociados con las altas temperaturas

(Página 35)



Lea Información importante de

seguridad (Página 34).

Seguridad y su

chimenea

La sécurité et

votre foyer

[FRENCH][ENGLISH] [SPANISH]

Safety and Your

Fireplace

 To prevent severe burns

and injuries, do Not

remove the barrier on the

appliance which prevents

direct contact with the

glass.

 Follow the safety instructions below

and be sure everyone in your household

understands this burn hazard:

• The surfaces on your ﬁreplace get

EXTREMELY HOT!

• The glass on the front of the

ﬁreplace reaches EXTREMELY HIGH

temperatures and can cause severe

burns if touched.

• Keep children away from an operating

ﬁreplace. Closely supervise children

in any room where a ﬁreplace is

operating to prevent contact with glass.

• Keep clothing, furniture, gasoline, and

other ﬂammable liquids away from the

ﬁreplace.

• Even after the gas is turned off,

ﬁreplace surfaces remain extremely

hot.

 Be sure to attach the enclosed Safety-

in-Operation Warnings where you

turn on your ﬁreplace, to help remind

everyone of the dangers associated with

high temperatures

(Page 35)

 Read Important Safety Information

(Page 34)

All parts of your

IHP ﬁreplace get

EXTREMELY HOT!

Toutes les parties de votre

foyer IHP deviennent

EXTRÊMEMENT CHAUDES !

¡Todas las partes de la

chimenea IHP se ponen

MUY CALIENTES!

INTRODUCTION

The Montebello® Series direct-vent, sealed-

combustion gas ﬁreplaces operate on natural

or propane gas. These appliances feature a

remotely controlled electronic intermittent pilot

ignition system (manual adjustment of the gas

valve settings is not possible).

The Montebello Series is a decorative ﬁreplace

and may not be installed and operated as the

primary heat source in a dwelling.

Electrical power (120 VAC line voltage) is recom-

mended to operate the ﬁreplace; however, four

(4) "AA" batteries can be used for full-time op-

eration or as a backup in case of a power outage.

Approved Vent Components

These ﬁreplaces are designed, tested, and listed

for operation and installation with 8" DV Lock di-

rect vent system components (8" inner, 11" outer)

by Innovative Hearth Products.

These approved vent system components

are labeled for identiﬁcation. USE ONLY AP-

PROVED VENT COMPONENTS. Do NOT use

any other manufacturer’s vent components

with these appliances.

Codes and Standards

These appliances comply with National Safety

Standards and are tested and listed by PFS

TECO (Report No. F14-106) to ANSI Z21.50:19

(in Canada, CSA-2.22:19) as vented gas ﬁre-

places.

These appliances are listed by PFS TECO for

installation in bedrooms and mobile homes.

Installation must conform to local codes. In

the absence of local codes, installation must

comply with the current National Fuel Gas

Code, ANSI Z223.1 (in Canada, the current

CAN/CGA-B149.1 installation code).

The appliance, when installed, must be electrically

grounded in accordance with local codes or, in the

absence of local codes, with the National Electrical

Code, ANSI/NFPA 70 (latest edition) or the Cana-

dian Electrical Code, CSA C22.1 (latest edition).

TABLE OF CONTENTS

Packaging .......................... 4

Introduction ......................... 4

General Information ................... 5

Massachusetts Requirements ........... 7

Cold Climate Insulation ................ 7

Manufactured Home Requirements ....... 7

Location ........................... 7

Vent Termination Clearances ............ 8

Minimum Clearances to Combustibles ...... 10

Detailed Installation Steps .............. 11

Typical Installation Sequence ........... 11

Step 1. Framing ..................... 11

Fireplace and Framing Speciﬁcations ....... 12

Step 2. Routing Gas Line .............. 13

Proper Sizing of Gas Line ............... 13

Step 3. Install the Vent System ......... 14

Vertical Termination Systems ............ 15

Vent Section Length Chart .............. 15

Vertical Vent Tables and Figures .......... 18

Horizontal Termination System .......... 19

Horizontal Vent Tables and Figures ....... 21

Step 4. Field Wiring .................. 23

Step 5. Removing Glass Door

Frame Assembly ................... 25

Step 6. Connecting Gas Line ........... 25

Step 7. Verify Appliance Operation ...... 25

Step 8. Installing Logs and Panels ...... 26

Step 9. Installing Glass Door .......... 28

Finishing Requirements ................ 29

Step 10. Attaching Safety-in-

Operation Warnings ................. 30

Installation Accessories ................ 31

Gas Conversion Kits ................... 32

Operation And Care Of Your Appliance ..... 38

Maintenance ......................... 39

Front Glass Enclosure Panel, Removal, and

Installation ........................ 40

Burner Adjustments ................... 41

Flame Appearance and Sooting .......... 41

Burner Air Shutter Adjustment ........... 42

Electronic Appliance Checkout .......... 42

Ordering Replacement Parts ............. 43

Wiring ........................... 43

Accessory Components ................ 44

Lighting Instructions .................. 46

Maintenance Schedule ................. 48

Troubleshooting Guide ................. 49

Replacement Parts List ................ 50

Warranty ........................... 55

Please read and understand these

instructions before beginning your

installation.

PACKAGING

The assembled ﬁreplace is packaged with the

following:

• Literature Kit (plastic bag shipped in-

side ﬁrebox), containing Installation and

Operation Manual (this manual), Safety

Flyer, Glass and Barrier Flyer and Safety-in-

Operation Warning Labels.

• One (1) bag Glowing Embers (Traditional)

• One (1) bag Platinum Embers (Traditional)

• One (1) bag Volcanic Stone (Traditional)

• Remote Control and Wall Receiver

Switch Kit

• Door Modesty Shield

• Log Grate (Traditional)

NOTE: For use with ﬁreplace as shipped from fac-

tory only. Not for use with Contemporary Burner/

Floor Kit.

REQUIRED ACCESSORIES

One of the following Firebox Liner Kits:

a. Ceramic Firebox Liner Kit–

Buff Rustic

b. Ceramic Firebox Liner Kit–

Red Rustic

c. Porcelain Firebox Liner Kit–

Black

d. Ceramic Firebox Liner Kit–

Red Herringbone

e. Ceramic Firebox Liner Kit–

Buff Herringbone

NOTE: Porcelain kits include side and back panels.

Optional for use with log sets. Required when using

the contemporary burner/ﬂoor kit.

NOTE:

• IF THE BARRIER BECOMES DAMAGED,

THE BARRIER SHALL BE REPLACED WITH

THE MANUFACTURER’S BARRIER FOR THIS

APPLIANCE.

• FOR USE WITH BARRIER(S) PART NO(S).

J7422 (40” MODELS) AND J7423 (45”

MODELS).

GENERAL INFORMATION

WARNING

This product can expose you to

chemicals including Carbon Black,

which is known to the State of

California to cause cancer, and

Carbon Monoxide, which is known

to the State of California to cause

birth defects or other reproductive

harm. For more information go to

www.P65Warnings.ca.gov

AVERTISSEMENT

Ce produit peut vous exposer

à des produits chimiques, y

compris du carbone noir qui est

reconnu par l'État de Californie

comme un produit cancérigène,

et du monoxyde de carbone, qui

est reconnu par l'État de Califor-

nie comme pouvant causer des

déformations fœtales ou per-

turber la fonction reproductive.

Pour plus d’information, aller

sur www.P65Warnings.ca.gov

General Information

900343-00J, 07/2023

Innovative Hearth Products

Montebello® DLX Series Direct-Vent Gas Fireplaces

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE

WARNING

Young children should be care-

fully supervised when they are

in the same room as the appli-

ance. Toddlers, young children

and others may be susceptible

to accidental contact burns. A

physical barrier is recommended

if there are at risk individuals in

the house. To restrict access to

a ﬁreplace or stove, install an

adjustable safety gate to keep

toddlers, young children and

other at risk individuals out of

the room and away from hot

surfaces.

AVERTISSEMENT

Les jeunes enfants devraient être

surveillés étroitement lorsqu’ils

se trouvent dans la même pièce

que l’appareil. Les tout petits,

les jeunes enfants ou les adultes

peuvent subir des brûlures s’ils

viennent en contact avec la sur-

face chaude. Il est recommandé

d’installer une barrière physique

si des personnes à risques habi-

tent la maison. Pour empêcher

l’accès à un foyer ou à un poêle,

installez une barrière de sécu-

rité; cette mesure empêchera les

tout petits, les jeunes enfants et

toute autre personne à risque

d’avoir accès à la pièce et aux

surfaces chaudes.

Children and adults should be alerted to the

hazards of high surface temperature and

should stay away to avoid burns or clothing

ignition.

Les enfants et les adultes devraient être

infor-més des dangers que posent les

températures de surface élevées et se

tenir à distance aﬁn d’éviter des brûlures

ou que leurs vêtements ne s’enﬂamment.

DO NOT ATTEMPT TO ALTER OR MODIFY

THE CONSTRUCTION OF THE APPLIANCE OR

ITS COMPONENTS. ANY MODIFICATION OR

ALTERATION MAY VOID THE WARRANTY,

CERTIFICATION AND LISTINGS OF THIS UNIT.

Installation and repair should be done by

a qualiﬁed service person. The appliance

should be inspected before use and at least

annually by a qualiﬁed service person. More

frequent cleaning may be required due to

excessive lint from carpeting, bedding ma-

terial, etcetera. It is imperative that control

compartments, burners and circulating air

passageways of the appliance be kept clean.

L’installation et la réparation devrait

être conﬁées à un technicien qualiﬁé.

L’appareil devrait faire l’objet d’une in-

spection par un technicien professionnel

avant d’être utilisé et au moins une fois

l’an par la suite. Des nettoyages plus

fréquents peuvent être nécessaires si les

tapis, la literie, et cetera produisent une

quantité importante de pous-sière. Il est

essentiel que les compartiments abritant

les commandes, les brûleurs et les con-

duits de circulation d’air de l’appareil

soient tenus propres.

Do not use this appliance if any part has

been under water. Immediately call a

qualiﬁed service technician to inspect the

appliance and to replace any parts of the

control system and any gas control which

have been under water.

Ne pas se servir de cet appareil s'il a été

plongé dans l'eau, complètement ou en

partie. Appeler un technicien qualiﬁé

pour inspecter l'appareil et remplacer

toute partie du système de contrôle et

toute commande qui ont été plongés

dans l'eau.

Only trim kit(s) supplied by the manufacturer

shall be used in the installation of this ap-

pliance.

Seules les trousses de garniture fournies

par le fabricant doivent être utilisées pour

l’installation de cet appareil.

Provide adequate clearances around air open-

ings and adequate accessibility clearance for

service and proper operation. Never obstruct

the front openings of the appliance.

These appliances are designed to operate on

natural or propane gas only. The use of other

fuels or combination of fuels will degrade

the performance of this system and may be

dangerous.

These appliances must not be connected to a

chimney or ﬂue serving a separate solid fuel

burning appliance.

NOTICE

If the barrier becomes damaged,

the barrier shall be replaced with

the manufacturer’s barrier for

this appliance.

WARNING

Improper installation, adjust-

ment, alteration, service or

maintenance can cause injury

or property damage. Refer to

this manual. For assistance or

additional information consult

a qualified installer, service

agency or the gas supplier.

WARNING

Failure to comply with these

installation instructions will result

in an improperly installed and

operating appliance, voiding its

warranty. Any change to this appli-

ance and/or its operating controls

is dangerous.

WARNING

Clothing or other flammable

material should not be placed

on or near the appliance.

AVERTISSEMENT

On ne devrait pas placer de

vêtements ni d’autres matières

inﬂammables sur l’appareil ni à

proximité.

WARNING

Any safety screen, guard or

barrier removed for servicing

the appliance must be replaced

prior to operating the appliance.

AVERTISSEMENT

Tout écran ou protecteur retiré

pour permettre l’entretien de

l’appareil doit être remis en

place avant de mettre l’appareil

en marche.

WARNING

Improper installation or use of

this appliance can cause serious

injury or death from ﬁre, burns,

explosion or carbon monoxide

poisoning.

General Information

900343-00J, 07/2023

Innovative Hearth Products

Montebello® DLX Series Direct-Vent Gas Fireplaces

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE

The appliance and its appliance main gas

valve must be disconnected from the gas

supply piping system during any pressure

testing of that system at test pressures in

excess of 1/2 psi (3.5 kPa).

The appliance must be isolated from the gas

supply piping system by closing its equipment

shutoff valve during any pressure testing of

the gas supply piping system at test pressures

equal to or less than 1/2 psi (3.5 kPa).

Oriﬁce Sizes—Sea Level To High Altitude

(All Models)

These appliances are tested and approved

for installation at elevations of 0–4500 feet

(0–1372 meters) above sea level, using the

standard burner oriﬁce sizes (marked with an

asterisk (*) in Table 4). For elevations above

4500 feet, contact your gas supplier or qualiﬁed

service technician.

Deration—At higher elevations, the amount

of BTU fuel value delivered must be reduced

by either:

• using gas that has been derated by the gas

company; or

• changing the burner oriﬁce to a smaller size

as regulated by the local authorities having

jurisdiction and by the (USA) National Fuel

Gas Code NFPA 54/ANSI Z223.1—latest

edition or, in Canada, the CAN/CGA-B149.1

codes—latest edition.

Install the appliance according to the regulations

of the local authorities having jurisdiction and,

in the USA, the National Fuel Gas Code NFPA

54 / ANSI Z223.1—latest edition or , in Canada,

the CAN/CGA-B149.1- latest edition.

Test gauge connections are provided on the

front of the gas control valve (identiﬁed IN for

the inlet and OUT for the manifold side).

Propane tanks are at pressures that will cause

damage to valve components. Verify that the

tanks have step-down regulators to reduce the

pressure to safe levels.

Gas Pressure—All Models

Appliance inlet and manifold gas pressure

requirements are listed in Tables 2 and 3.

Inlet Gas Supply Pressure

Fuel # Minimum Maximum

Natural

Gas

5.5" WC

(1.37 kPa)

10.5" WC

(2.61 kPa)

Propane 11.0" WC

(2.74 kPa)

13.0" WC

(3.23 kPa)

Table 2

Manifold Gas Supply Pressure

Fuel # Low High

Natural

Gas

1.6" WC

(.4 kPa)

3.5" WC

(.87 kPa)

Propane 6.3" WC

(1.57 kPa)

10.0" WC

(2.49 kPa)

Table 3

In Canada - CAN/CGA-2.17-M91 (R2009)

(high altitude):

THE CONVERSION SHALL BE CARRIED

OUT BY A MANUFACTURER’S AUTHO-

RIZED REPRESENTATIVE, IN ACCOR-

DANCE WITH THE REQUIREMENTS OF

THE MANUFACTURER, PROVINCIAL OR

TERRITORIAL AUTHORITIES HAVING

JURISDICTION AND IN ACCORDANCE

WITH THE REQUIREMENTS OF THE

CAN/CGA-B149.1 OR CAN/CGA-B149.2

INSTALLATION CODES.

Gas Valve Diagram

The SIT Proﬂame gas valve is shown in Figure 1.

Input (BTU/HR)

Model Nat.Gas * Propane **

Traditional

40"

32,000 to 50,000 32,000 to 50,000

45"

40,000 to 57,000 43,000 to 56,000

Contemporary

40" CD

32,000 to 50,000 31,000 to 40,000

45" CD

40,000 to 57,000 31,000 to 40,000

Table 1

* Standard input from factory

** Standard input after LP conversion

Burner Oriﬁce Sizes

Elevation 0–4500 ft ( 0–1372 m)

Model

Nat.Gas *

drill size (inches) Propane **

drill size (inches)

Traditional

40"

0.1405" (#28)

cat. no. H2286

0.082" (#45)

cat. no. J7577

45" 0.150" (#25)

cat. no.

J8001

0.086" (#44)

cat. no.

H2287

Contemporary

40" CD

0.1405" (#28)

cat. no. H2286

0.073" (#49)

cat. no. H8807

45" CD

0.150" (#25)

cat. no. H8808

0.073" (#49)

cat. no. H8807

Table 4

* Standard size installed at factory

** Standard size after LP conversion

NOTE: Flame appearance will diminish 4% per

thousand feet of altitude.

These electronic appliances are remotely

controlled and feature an electronic intermit-

tent pilot ignition system or standing pilot.

External electrical power is required to operate

these units.

These electronic models come standard with a

remotely-modulated gas valve; ﬂame appear-

ance and heat output cannot be controlled at

the gas valve. The BTU Input for these appli-

ances is shown in Table 1.

General Information

900343-00J, 07/2023

Innovative Hearth Products

Montebello® DLX Series Direct-Vent Gas Fireplaces

Wire

(From DFC Wire

Harness)

Pressure

Regulator

Tower

Yellow Ground Wire

(From DFC Wire

Harness)

Green Wire

(From DFC Wire

Harness)

Inlet (In) Test Port

Manifold (Out)

Test Port

Connect GTMS

Wire Harness

Figure 1—SIT Proﬂame Valve

Main Gas Inlet

3/8" NPT

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE

This appliance is only for use with the type of

gas indicated on the rating plate. This appliance

is not convertible for use with other gases, un-

less a certiﬁed kit is used.

Cet appareil doit être utilisé uniquement

avec le type de gaz indiqué sur la plaque

signalétique. Cet appareil ne peut être con-

verti à d'autres gaz, sauf si une trousse de

conversion est utilisée.

CAUTION: Ensure that the cross members

are not cut or weakened during installa-

tion. The structural integrity of the manu-

factured home ﬂoor, wall, and ceiling / roof

must be maintained.

CAUTION: This appliance must be ground-

ed to the chassis of the manufactured

home in accordance with local codes or

in the absence of local codes, with the

National Electrical Code ANSI / NFPA 70—

latest edition or the Canadian Electrical

Code CSA C22.1—latest edition.

LOCATION

In selecting the location, the aesthetic and

functional use of the appliance are primary

concerns. However, vent system routing to

the exterior and access to the fuel supply are

also important.

Due to high temperatures, the appliance

should be located out of trafﬁc and away from

furniture and draperies (Figure 2).

Drywall

Top Of Fireplace

Opening Non-Combustible

Figure 2—Typical Installation

When the unit is installed with one side ﬂush with

a wall, the wall on the other side of the unit must

not extend beyond the front edge of the unit.

Cross Corner

Application

Room Divider

Application

Recessed

Application

Island

Application

Flat on Wall

Application

Flat

Application

HORIZONTAL VENT VERTICAL VENT

COMMONWEALTH OF MASSACHUSETTS

REQUIREMENTS

These appliances are approved for installation in

the US state of Massachusetts if the following

additional requirements are met:

• Install this appliance in accordance with

Massachusetts Rules and Regulations 248

C.M.R. Sections 4.00 through 8.00.

• Installation and repair must be done by a

plumber or gas ﬁtter licensed in the Com-

monwealth of Massachusetts.

• The ﬂexible gas line connector used shall

not exceed 36 inches (92 centimeters) in

length.

• The individual manual shut-off must be a

T-handle type valve.

Massachusetts Horizontal Vent Requirements

In the Commonwealth of Massachusetts, hori-

zontal terminations installed less than seven

(7) feet above the ﬁnished grade must comply

with the following additional requirements:

• A hard wired carbon monoxide detector

with an alarm and battery back-up must be

installed on the ﬂoor level where the gas

ﬁreplace is installed. The carbon monoxide

detector must comply with NFPA 720, be

ANSI/UL 2034 listed and be ISA certiﬁed.

• A metal or plastic identiﬁcation plate must

be permanently mounted to the exterior of

the building at a minimum height of eight (8)

feet above grade and be directly in line with

the horizontal termination. The sign must

read, in print size no less than one-half (1/2)

inch in size, GAS VENT DIRECTLY BELOW.

KEEP CLEAR OF ALL OBSTRUCTIONS.

COLD CLIMATE INSULATION

For cold climate installations, seal all cracks

around your appliance with noncombustible

material and wherever cold air could enter

the room. It is especially important to insulate

outside chase cavity between studs and under

ﬂoor on which appliance rests, if ﬂoor is above

ground level. Gas line holes and other openings

should be caulked or stuffed with unfaced

ﬁberglass insulation.

If the ﬁreplace is being installed on a cement

slab in cold climates, a sheet of plywood or

other raised platform can be placed underneath

to prevent cold transfer to the ﬁreplace and

into the room. It also helps to sheetrock inside

surfaces and tape for maximum air tightness

and caulk ﬁrestops.

MANUFACTURED HOME REQUIREMENTS

This appliance may be installed in an aftermar-

ket permanently located, manufactured home

and must be installed in accordance with the

manufacturer's instructions.

Cet appareil peut être installé cómme

du matéri-el d'origine dans une maison

préfabriquée (É.U. seulement) ou mobile

et doit être installé selon les instructions

du fabricant.

En raison des températures élevées,

l’appareil devrait être installé dans un

endroit où il y a peu de circulation et loin

du mobilier et des tentures (Figure 2).

The location should also be free of electrical,

plumbing or other heating/air conditioning

ducting.

These direct-vent appliances are uniquely

suited for installations requiring a utility shelf

positioned directly above the ﬁreplace. Utility

shelves like these are commonly used for

locating television sets and decorative plants.

Be aware that this is a heat producing ap-

pliance. Objects placed above the unit are

exposed to elevated temperatures.

Do not insulate the space between the

appliance and the area above it (see Figure

7 on Page 10).

The minimum height from the base of the

appliance to the underside of combustible

materials used to construct a utility shelf in

this fashion is shown in Figure 7 on Page 10.

The appliance must be mounted on a fully

supported base extending the full width

and depth of the unit. The appliance may be

located on or near conventional construction

materials. However, if installed on combustible

materials, such as carpeting, vinyl tile, or other

combustible material other than wood ﬂooring,

the appliance shall be installed on a metal or

wood panel extending the full width and depth

of the appliance.

General Information

900343-00J, 07/2023

Innovative Hearth Products

Montebello® DLX Series Direct-Vent Gas Fireplaces

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE

(76 mm)

Termination Kit

Combustible Projection

greater than 2-1/2” in length

Horizontal Vent Termination Clearances

Combustible Projection

2-1/2” or less in length

24"

(610 mm)

Ventilated Or

Unventilated Soffit

See Figure 28 on Page 20 for the recess allowances,

into exterior walls, of the Horizontal Terminations.

Termination Heights For Vents

Above Flat Or Sloped Roofs

Ref. NFPA 54 / ANSI Z223.1

Roof Pitch * Feet * Meters

Flat to 6/12 1.0 0.3

6/12 to 7/12 1.25 0.38

7/12 to 8/12 1.5 0.46

8/12 to 9/12 2.0 0.61

9/12 to 10/12 2.5 0.76

10/12 to 11/12 3.25 0.99

11/12 to 12/12 4.0 1.22

12/12 to 14/12 5.0 1.52

14/12 to 16/12 6.0 1.83

16/12 to 18/12 7.0 2.13

18/12 to 20/12 7.5 2.29

20/12 to 21/12 8.0 2.44

The vent / air intake termination clearances

above the high side of an angled roof is as

shown in the following chart:

Roof Pitch is X/12

2 FT

MIN.

2 FT MIN.

Lowest

Discharge

Opening

*H = MINIMUM HEIGHT FROM ROOF TO

LOWEST DISCHARGE OPENING OF VENT

TERMINATION HEIGHTS FOR VENTS ABOVE

FLAT OR SLOPED ROOFS

Horizontal Overhang

Vertical

Wall

Vent

Termination

Storm Collar

Concentric

Vent Pipe

Flashing

1” (25.4 mm) Minimum

Clearance to Combustibles

Vertical Vent Termination Clearances

Figure 4

VENT TERMINATION CLEARANCES

These instructions should be used as a

guideline and do not supersede local codes

in any way. Install vent according to local

codes, these instructions, the current National

Fuel Gas Code (ANSI-Z223.1) in the USA or

the current standards of CAN/CGA-B149.1 in

Canada.

Vertical Vent Termination Clearances

Terminate multiple vent terminations according

to the installation codes listed above. Also see

Figure 3.

Terminate single vent caps relative to building

components according to Figures 3 and 4.

Horizontal Vent Termination Clearances

The horizontal vent termination must have a minimum of 3" (77 mm) clearance to any overhead

combustible projection of 2-1/2" (64 mm) or less (see Figure 5). For projections exceeding 2-1/2"

(64 mm), see Figure 5. For additional vent location restrictions refer to Figure 6 on Page 9.

12”

(305mm)

Minimum

Figure 3—Multiple Terminations

Figure 5—Side Elevation View

General Information

900343-00J, 07/2023

Innovative Hearth Products

Montebello® DLX Series Direct-Vent Gas Fireplaces

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE

Figure 6 - Horizontal vent termination clearances for buildings with combustible and noncumbustible exteriors

X

V V



= Vent terminal

= Air supply inlet

= Area terminal NOT permitted

= 9" U.S. (12" Canada)

FFixed Closed

Window

Operable

Window

36"

(91.4 cm)

MINIMUM CLEARANCES

Clearance Description US Installation Canadian Installation 

A = Clearance above grade, veranda, porch,

deck, or balcony.

18" (46 cm) 18" (46 cm) 

B = Clearance to window or door that may be

opened.

6" (15.2 cm) for appliances < 10,000 BTU/hr (3kW),

9" (23 cm) for appliances > 10,000 BTU/hr (3kW) and <

50,000 BTU/hr (15kW),

12" (30 cm) for appliances > 50,000 BTU/hr (15kW).

6" (15.2 cm) for appliances < 10,000 BTU/hr (3kW),

12" (30 cm) for appliances > 10,000 BTU/hr (3kW) and <

100,000 BTU/hr (30kW),

36" (91 cm) for appliances > 100,000 BTU/hr (30kW).

C = Clearance to permanently closed window. 9" (229 mm) recommended to prevent window

condensation.

12" (305 mm) recommended to prevent window

condensation.

D = Vertical clearance to ventilated sofﬁt

located above the terminal within a

horizontal distance of 36" (91.4 cm)

from center line of terminal.

24" (61 cm) 24" (61 cm)

E = Clearance to unventilated sofﬁt. 24" (61 cm) 24" (61 cm)

F = Clearance to outside corner. 5" (12.7 cm) 5" (12.7 cm)

G = Clearance to inside corner. 24" (61 cm) 36" (91.4 cm)

H = Clearance to each inside of center line

extended above meter/regulator assembly.

3 ft (91.4 cm) within a height of 15 ft above the

meter/regulator assembly.

3 ft (91.4 cm) within a height of 15 ft above the

meter/regulator assembly.

I = Clearance to service regulator vent outlet. 3 ft (91.4 cm) 3 ft (91.4 cm) 

J = Clearance to non-mechanical air supply

inlet to building or combustion air inlet to

any other appliance.

6" (15.2 cm) for appliances < 10,000 BTU/hr (3kW);

9" (23 cm) for appliances > 10,000 BTU/hr (3kW)

and < 50,000 BTU/hr (15kW);

12" (30 cm) for appliances > 50,000 BTU/hr (15kW).

6" (15.2 cm) for appliances < 10,000 BTU/hr (3kW);

12" (30 cm) for appliances > 10,000 BTU/hr (3kW)

and < 100,000 BTU/hr (30kW);

36" (91.4 cm) for appliances > 100,000 BTU/hr (30kW).

K = Clearance to mechanical air supply inlet. 3 ft (91.4 cm) above, if within 10 ft (3 m) horizontally.6 ft (1.83 m) 

L = Clearance above paved sidewalk or paved

driveway located on public property.

7 ft (2.13 m) 7 ft (2.13 m) 

M = Clearance under veranda, porch, deck, or

balcony.

18" (46.0 cm)  18" (46.0 cm) 

 In accordance with the current ANSI Z223.1 / NFPA 54 National Fuel Codes (latest editions).

 In accordance with the current CAN/CGA-B149.1 Installation Code (latest editions).

 A vent shall not terminate directly above a sidewalk or paved driveway that is located between two single-family dwellings and serves both dwellings.

 Only permitted if veranda, porch, deck, or balcony is fully open on a minimum of two sides beneath the ﬂoor.

NOTE:

• Local codes or regulations may require

different clearances.

• Location of vent termination must NOT

interfere with access to electrical service.

X

V V



= Vent terminal

= Air supply inlet

= Area terminal NOT permitted

= 9" U.S. (12" Canada)

FFixed Closed

Window

Operable

Window

36"

(91.4 cm)

X

V V



= Vent terminal

= Air supply inlet

= Area terminal NOT permitted

= 9" U.S. (12" Canada)

FFixed Closed

Window

Operable

Window

36"

(91.4 cm)

[DETAIL]

Inside Corner

Center Line of

Horizontal

Termination

Inside Corner

Ventilated

Sofﬁt

Exterior Wall

[DETAIL]

See Item “D” in table below.

General Information

900343-00J, 07/2023

Innovative Hearth Products

Montebello® DLX Series Direct-Vent Gas Fireplaces

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE

*NOTE: 3" (75 mm) above any horizontal/inclined vent component.

**NOTE: See Page 11, Step 1 for clearance requirements to the nailing

ﬂange located at each side of the unit and any screw heads adjacent

to it. See Page 30 for hearth extension requirements.

NOTE: Insulation shield (F4358, see Page 10) must be installed

when blown or loose-ﬁll insulation is used, and is required for

all attic installations.

Shelf Height

To provide for the lowest possible shelf surface, the venting attached to

the top vent should be routed in a way to minimize obstructions to the

space above the appliance. Do not insulate the space between the ap-

pliance and the area above it (see Figure 7). The minimum height from

the base of the appliance to the underside of combustible materials used

to construct a utility shelf in this fashion is shown in Figure 7.

Wall Finishes / Surrounds / Mantels

NOTE: Combustible wall ﬁnish materials and/or surround materials must

not be allowed to encroach the area deﬁned by the appliance front face

(black sheet metal). Never allow combustible materials to be positioned

in front of or overlapping the appliance face. See Figure 9 and Figure

51 on Page 29.

Non-combustible materials, such as surrounds and other appliance trim,

may be installed on the appliance front face with these exceptions: they

must not cover any portion of the removable glass panel.

Vertical installation clearances to combustible mantels vary according

to the depth of the mantel. See Figure 8. Mantels constructed of non-

combustible materials may be installed at any height above the appliance

opening. Minimum clearance requirements include any projections such

as shelves, window sills, mantels, etc. above the appliance.

NOTE: We recommend the use of high temperature paint (rated 175° F

or higher) on the underside of the mantel.

Minimum clearance requirements include any projections such as

shelves,window sills, mantels, etc. above the appliance.

MINIMUM CLEARANCES TO COMBUSTIBLES

The appliance is approved with zero clearance to combustible materials

on all sides (as detailed in Table 5), with the following exception: When

the unit is installed with one side ﬂush with a wall, the wall on the

other side of the unit must not extend beyond the front edge of the

unit. In addition, when the unit is recessed, the side walls surrounding

the unit must not extend beyond the front edge of the unit (see Figure 2).

Figure 9

17 in.

(432 mm)

14 in.

(356 mm)

8-1/4 in.

(210 mm)

45°

12 in.

(305 mm)

5 in.

(127 mm)

12 (305)

10 (254)

8 (203)

6 (152)

4 (102)

(178)

(432)

(381) 13

(330) 2 (51)

(229)

(279)

Figure 8

Combustible Materials

Allowed In Shaded Area

"Safe Zone" Top View of

Fireplace

Minimum Distance to

Protected Side Wall

Minimum Distance to

Unprotected Side Wall

Side

Wall

Side

Wall

MANTEL

CLEARANCES

Inches (mm)

Top of Appliance

MANTEL

Fireplace

(side view)

Figure 7

APPLIANCE MINIMUM CLEARANCES*

Inches (millimeters)

Sides 1/2 (13), 0 (0) Spacers **

Top Spacers 0 (0)

Floor 0 (0)

Back 1/2 (13), 0 (0) Spacers

Bottom of Appliance To Ceiling 69 (1743)

Vent 3 (77) Top* / 1 (26) Sides & Bottom

SERVICE CLEARANCES Feet (meters)

Front 3 feet (0.9 meters)

Table 5

Combustible Shelf Height—Inches (millimeters)

Top Vent—with 2 Feet Vertical Vent and One 90 Degree Elbow

Model 8" DV Lock

40 in. *84-1/16 (2135)

45 in. *89-1/16 (2252)

* Includes 3" clearance to combustibles (required above vent components)

Do not insulate the

space between the

appliance and the

area above it.

2-1/2 ft

(to centerline)

Vertical

Vent (minimum)

Shelf Height

(see table)

Shelf Above Fireplace With Top Venting

General Information

900343-00J, 07/2023

Innovative Hearth Products

Montebello® DLX Series Direct-Vent Gas Fireplaces

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE

TYPICAL INSTALLATION SEQUENCE

The typical sequence of installation is outlined

below. However, each installation is unique and

may result in variations to the steps described.

See the Page numbers references in the follow-

ing steps for detailed procedures.

Step 1. (Page 11) Construct the appliance

framing. Position the appliance within

the framing and secure with nailing

brackets.

Step 2. (Page 13) Route gas supply line to the

right side.

Step 3. (Page 14) Install the vent system and

exterior termination.

Step 4. (Page 23) Connect 120 VAC electrical

power to the appliance receptacle.

Step 5. (Page 25) Remove glass door assem-

bly.

Step 6. (Page 25) Make connection to gas

supply.

Step 7. (Page 25) Verifying appliance opera-

tion.

Step 8. (Page 26) Install optional ﬁrebox liner

panels, volcanic stone, glowing embers

and logs.

contemporary burner/ﬂoor kit, por-

celain panels, and media (all three

(3) items required for contemporary

models).

Step 9. (Page 28) Install glass door assembly.

Step 10. (Page 30) Attach safety in operation

warnings. Left Side Front Corner of Fireplace Shown

(Right Side Requirements the Same)

Unit Being Secured By Its Nailing Flanges

To The Framing

NOTE: The nailing ﬂanges, combustible members and

screw heads located in areas directly adjacent to the

nailing ﬂanges, are EXEMPT from the 1/2” clear-

ance to combustible requirements for the ﬁrebox

outer wrapper. Combustible framing may be in direct

contact with the nailing ﬂanges and may be located

closer than 1/2” from screw heads and the ﬁrebox

wrapper in areas adjacent to the nailing ﬂanges.

Frame the opening to the exact dimensions speciﬁed

in the framing details of this manual.

Unit Being Secured by Its Nailing

Flanges to the Framing

Unit Being Secured by Its Nailing

Flanges to the Framing

Note: The nailing flanges, combustible members

and screw heads located in areas directly adjacent

to the nailing flanges, are EXEMPT from the 1/2”

clearance to combustible requirements for the

firebox outer wrapper. Combustible framing may be

in direct contact with the nailing flanges and may

be located closer than 1/2” from screw heads and

the firebox wrapper in areas adjacent to the nailing

flanges. Frame the opening to the exact dimensions

specified in the framing details of this manual.

Use Top Flange For

1/2” Thick Drywall

Use Bottom Flange For

5/8” Thick Drywall

Front Of

Fireplace

Use Center Flange

For Flush Mount

Left Side Front Corner of Fireplace Shown

(Right Side Requirements the Same)

Unit Being Secured By Its Nailing Flanges

To The Framing

Step 1. FRAMING

Frame these appliances as illustrated in Figure

11 on Page 12, unless the appliance is to be

installed in a corner. See Figure 12 on Page

13 for corner framing installations. All framing

details must allow for a minimum clearance to

combustible framing members as shown in

Table 5 on Page 10.

If the appliance is to be elevated above ﬂoor

level, a solid continuous platform must be

constructed below the appliance.

Headers may be in direct contact with the

appliance top spacers but must not be sup-

ported by them or notched to ﬁt around them.

All construction above the appliance must be

self-supporting, DO NOT use the appliance for

structural support.

A header heat shiled is taped to the top of the

ﬁreplace. Slide the heat shield into the framing

and attach the heat shield using the screws in

the standoff (see Figure 10).

The ﬁreplace should be secured to the side

framing members using the unit's nailing

ﬂanges—one top and bottom on each side of

the ﬁreplace front (see Figure 10). Use 8d nails

or their equivalent.

Figure 10

The heat shield is designed to protect framing. Step 1. Heat shield rests on top standoffs

Step 2. Afﬁx shield with 5/16" hex screws into

front standoff.

Step 3. Heat shield will now protect framing

from heat from ﬂue.

Installing the Heat Shield

Installation

900343-00J, 07/2023

Innovative Hearth Products

Montebello® DLX Series Direct-Vent Gas Fireplaces

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE

DETAILED INSTALLATION STEPS

The appliance is shipped with all gas

controls and components installed and pre-

wired.

1. Remove the shipping carton, exposing the

front glass door on the valve access side.

2. Using a Phillips screwdriver, unfasten two

(2) screws located at the top of the glass

frame (see Figure 47 on page 28). Tilt the

top of the glass frame away from the unit.

Lift it carefully off the bottom door track

and set the door aside, protecting it from

inadvertent damage.

WARNING

Failure to position the parts in

accordance with these diagrams

or failure to use only parts speciﬁ-

cally approved with this appliance

may result in property damage or

personal injury.

AVERTISSEMENT

Risque de dommages ou de

blessures si les pièces ne sont

pas installées conformément à

ces schémas et ou si des pièces

autres que celles spéciﬁquement

approuvées avec cet appareil sont

utilisées.

Front Standoff

Top front of ﬁreplace

Non-combustible board

Framing

Figure 11—Fireplace and Framing Speciﬁcations

Top View

Front View

5-1/8 (130)

Right Side View

14-1/8

8-1/2”

(216)

5-1/4”

(133)

(359) 26-1/2

(673)

(660)

25-1/2

(648)

1/2 (13)

(178)

19-5/8

(498)

Gas Inlet

(This

Side

Only)

Electrical

Inlet

10-3/8

(264)

Fireplace Dimensions

Model A B C D E F G H J

40 in. in. 50-5/8 39-1/4 45 25-3/8 34 37-5/8 33-1/8 29-3/8 34-3/4

mm 1286 997 1143 645 864 956 841 746 883

45 in. in. 56-3/4 44-1/4 50 28-3/8 40-1/8 43-5/8 38-1/8 34-1/2 41

mm 1442 1124 1270 721 1019 1108 968 876 1041

Notes

Diagrams, illustrations and photo-

graphs are not to scale — consult

installation instructions. Product

designs, materials, dimensions,

speciﬁcations, colors and prices are

subject to change or discontinuance

without notice.

Vent Size

Coaxial DV

Vent Size

8" Inner

11" Outer

26-1/2

(673)

(660)

5-1/8 (130)

These appliances comply with CSA P.4.1-15 “Testing Method for Measuring Annual Fireplace

Efﬁciency. P4 (EnerGuide) is a measurement of the Canadian Ofﬁce of Energy Efﬁciency.

Framing Dimensions

Model A B C

40 in. in. 50-3/4 45 75-1/8

mm 1289 1143 1908

45 in. in. 56-7/8 50 80-1/8

mm 1445 1270 2035

8-1/2

(216)

(

330

)

VENT FRAMING

TOP VENT WITH 2 FEET

VERTICAL VENT AND

ONE 90° ELBOW

Framing should be constructed

of 2x4 or larger lumber.

Inches (mm)

(641)

25-1/4

(

381

)

6-1/2

(165)

1/2 A

PIPE CENTERLINE

8-1/2

(216)

(

330

)

VENT FRAMING

TOP VENT WITH 2 FEET

VERTICAL VENT AND

ONE 90° ELBOW

Framing should be constructed

of 2x4 or larger lumber.

Inches (mm)

(660)

(

381

)

6-1/2

(165)

1/2 A

PIPE CENTERLINE

Installation

900343-00J, 07/2023

Innovative Hearth Products

Montebello® DLX Series Direct-Vent Gas Fireplaces

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE

Thermal Efﬁciency (%)

Natural Gas

Model P4

40 in. 35.8

45 in. 51.2

Figure 12—Corner Framing with Horizontal Termination (8DVLHT)

Proper Sizing of Gas Line

Properly size and route the gas supply

line from the supply regulator to the area

where the appliance is to be installed per

requirements outlined in the National Fuel Gas

Code, NFPA 54—latest edition (USA) or CAN/

CGA-B149.1—latest edition (Canada).

NOTES:

• All appliances are factory-equipped with a

ﬂexible gas line connector and 1/2" shutoff

valve (see Figure 36 on Page 25).

• See Massachusetts Requirements on Page

6 for additional requirements for installations

in the state of Massachusetts in the USA.

• The gas supply line should Not be connected

to the appliance until Step 6 (Page 25).

• A pipe joint compound rated for gas should be

used on the threaded joints. Ensure propane

resistant compounds are used in propane

applications. Be very careful that the pipe

compound does not get inside the pipe.

• It is recommended to install a sediment trap

in the supply line as close as possible to the

appliance (see Figure 36 on Page 25).

• Check with local building ofﬁcial for local

code requirements.

IMPORTANT: If propane is used, be aware that

if tank size is too small (i.e. under 100 lbs, if

this is the only gas appliance in the dwelling.

Ref. NPFA 58), there may be loss of pressure,

resulting in insufﬁcient fuel delivery (which

can result in sooting, severe delayed ignition

or other malfunctions). Any damage resulting

from an improper installation, such as this,

is not covered under the limited warranty.

Right Side

Front Corner

Of Fireplace

Framing

6-1/4”

(159 mm)

19-5/8”

(498 mm)

Step 2. ROUTING GAS LINE

Route a 1/2" (13 mm) gas line along the inside

of the right side framing as shown in Figure

13. Gas lines must be routed, constructed and

made of materials that are in strict accordance

with local codes and regulations.

All appliances are factory-equipped with a

ﬂexible gas line connector and 1/2" shutoff

valve. (See Step 6 on Page 25).

The incoming gas line should be piped into the

valve compartment and connected in one of the

two methods as shown in Figure 36 on Page 25.

Never use galvanized or plastic pipe. Refer to

Table 6 for proper sizing of the gas supply

line, if black iron pipe is being used. Gas lines

must be routed, constructed and made of

materials that are in strict accordance with

local codes and regulations. We recommend

that a qualiﬁed individual such as a plumber

or gas ﬁtter be hired to correctly size and route

the gas supply line to the appliance. Installing

a gas supply line from the fuel supply to the

appliance involves numerous considerations of

materials, protection, sizing, locations, controls,

pressure, sediment, and more. Certainly no one

unfamiliar and unqualiﬁed should attempt sizing

or installing gas piping.

Figure 13

Schedule 40—Black Iron Pipe

Inside Diameter (Inches)

Schedule 40 Pipe

Length (feet) Natural

Gas Propane

Gas

0–10 1/2" 3/8"

10–40 1/2" 1/2"

40–100 1/2" 1/2"

100–150 3/4" 1/2"

150–200 3/4" 1/2"

Table 6

Back wall of chase/enclosure

(including any finishing materials)

Model A B C D

40 in. in. 50-5/8 83-5/8 59-1/8 41-7/8

mm 1286 2124 1502 1064

45 in. in. 56-3/4 89-7/8 63-1/2 44-7/8

mm 1441 2283 1613 1140

Installation

900343-00J, 07/2023

Innovative Hearth Products

Montebello® DLX Series Direct-Vent Gas Fireplaces

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE

RESTRICTOR

APPLIANCE VENT OUTLET

When vertically terminating the vent system above

the roof, install a vent restrictor in the top vent of

the fireplace outlet. Install the restrictor as shown

from inside the unit, in the inner fireplace collar

Figure 14—Vent Restrictor Installation

Step 3. INSTALL THE VENT SYSTEM

General Information

These instructions should be used as a guide-

line and do not supersede local codes in any

way. Install vent according to local codes,

these instructions, the current National Fuel

Gas Code (ANSI-Z223.1) in the USA or the

current standards of CAN/CGA-B149.1 and

-B149.2 in Canada.

Ensure clearances are in accordance with

local installation codes and the requirements

of the gas supplier.

Dégagement conforme aux codes

d'installation locaux et aux exigences du

foumisseunde gaz.

Use only approved venting components.

See Approved Vent Components on

Page 4.

These ﬁreplaces must be vented directly

to the outside.

The vent system may not service multiple

appliances, and must never be connected to a

ﬂue serving a separate solid fuel burning ap-

pliance. The vent pipe is tested to be run inside

an enclosing wall (such as a chase). There is

no requirement for inspection openings in the

enclosing wall at any of the joints in the vent pipe.

Installation of Vent Restrictor

A vent restrictor may be needed with this

appliance. The restrictor is installed in the

appliance top ﬂue outlet as shown in Figure 14,

For vertical venting from 6 feet to 12 feet or

more, from the top of the ﬁreplace to the top

of the termination, the installation of a vent

restrictor is required.

If necessary, install a vent restrictor in the

appliance ﬂue outlet as shown in Figure 14. The

vent restrictor is held in place by friction, only.

NOTE: The restrictor is included within the

ﬁrebox.

Select Venting System—Horizontal or Vertical

With the appliance secured in framing, de-

termine vent routing and identify the exterior

termination location. The following sections

describe vertical (roof) and horizontal (exterior

wall) vent applications. Refer to the section

relating to your installation. A list of approved

venting components is shown on Page 31.

Installation

900343-00J, 07/2023

Innovative Hearth Products

Montebello® DLX Series Direct-Vent Gas Fireplaces

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE

Figure 15

Table 7: Vent Section Length Chart

Termination

Flashing And

Storm Collar

Firestop/Spacer

8DVL 6/12/24/36/48

Vent Sections

40' Max

(12.2 M)

6' Min

(1.8 M)

1" (25 mm)

Minimum

Clearance to

Combustibles

VERTICAL TERMINATION SYSTEMS (ROOF)

See Figure 15 and Figures 23 through 25 on

Page 18 and their associated Vertical Vent

Tables which illustrate the various vertical venting

conﬁgurations that are possible for use with

these appliances. 8" DV Lock pipe applications

are shown in these ﬁgures. A Vertical Vent

Table summarizes each system’s minimum and

maximum vertical and horizontal length values

that can be used to design and install the vent

components in a variety of applications.

The vertical vent system terminates through

the roof. The minimum vent height above the

roof and/or adjacent walls is speciﬁed in ANSI

Z223.1—latest edition (In Canada, the current

CAN/CGA-B149.1 installation code) by major

building codes. Always consult your local

codes for speciﬁc requirements. A general

guide to follow is the Gas Vent Rule (refer to

Figure 4 on Page 8).

Vertical (Straight) Installation

(Figure 15)

Determine the number of straight vent sections

required. 4-1/2" (114 mm), 10-1/2" (267 mm),

22-1/2" (572 mm), 34-1/2" (876 mm) and

46-1/2" (1181 mm) net section lengths are

available (see Tables on this page and Page

18—Vent Sections). Plan the vent lengths so

that a joint does not occur at the intersection of

ceiling or roof joists. Refer to the Vent Section

Length Chart.

NOTE: Convert inches into metric equivalent

measurement, as follows:

Millimeters (mm) = Inches x 25.4

Centimeters (cm) = Inches x 2.54

Meters (M) = Inches x .0254

Model Effective Length

8DVL6 4-1/2"

8DVL12 10-1/2"

8DVL24 22-1/2"

8DVL36 34-1/2"

8DVL48 46-1/2"

Table 8—Effective Vent Length

lanimoN

htgneLnoitceS )sehcni( 621426

noitceSteN )sehcni(htgneL 2/1-42/1-012/1-2

/1-4

/1-64

tneVfothgie

noitceStneVforebmuN

sehcnitf

5.4573.0100001

957.0200002

5.01578.0010001

5152.1110002

5.91526.1210003

1257.1020002

5.22578.1001001

5.52521.2120003

5.13526.2030003

5.43578.2000101

5.73521.3111003

5.34526.3021003

5457.3002002

5.64578.3000011

5.94521.4102003

1552.4100012

5.55526.4012003

7557.4001102

6652.5022004

5.76526.5003003

9657.5000202

2761030

5.37521.6100203

5.97526.6010203

1857.6000112

095.7021014

5.19526.7002013

3957.7000022

6981012

5.79521.8100023

2015.8200024

5.301526.8000303

80191003

4115.9020024

71157.9105006

5.811578.9110305

6215.01001304

5.031578.01101305

53152.11006006

8315.11000404

5.931526.11000033

5.241578.11100405

noitceSlanimoN )sehcni(htgneL 621426384T

noitceSteN )sehcni(htgneL 2/1-42/1-012/1-222/1-432/1-64

tneVfothgieHsnoitceStneVforebmuN

sehcnitf

44121100034

0515.21010034

5.451578.21110035

5.061573.31020035

5.271573.41000505

77157.41100506

38152.51010506

6815.51000044

5.091578.51100045

5.691573.61010045

5.502521.71011507

70252.71000606

5.112526.71100607

5.712521.81010607

5.922521.91001607

5.232573.91000055

73257.91100056

5.142521.02000707

6425.02100708

25212010708

46222001708

67232000808

97252.32000066

5.082573.32100809

5.382526.32100067

5.982521.42010067

5.103521.52001067

5.013578.52000909

5135.621009001

5.523521.72000077

0335.72100078

63382010078

54357.82000 01001

5.943521.92100 01011

27313000088

5.673573.13100089

5.973526.13000 11011

5.814578.43000099

32452.531000901

56457.8300000101

8DVL 6/12/24/36/48

Vent Sections

Installation

900343-00J, 07/2023

Innovative Hearth Products

Montebello® DLX Series Direct-Vent Gas Fireplaces

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE

Figure 16

Vertical (Offset) Installation

Analyze the vent routing and determine the

quantities of vent sections and number of elbows

required. Refer to Vertical Vent Figures and

Tables on Page 18 to select the type of vertical

installation desired. Vent sections are available

in net lengths of 4-1/2" (114 mm), 10-1/2" (267

mm), 22-1/2" (572 mm), 34-1/2" (876 mm) and

46-1/2" (1181 mm). Refer to the Vent Section

Length Chart on Page 15 for an aid in select-

ing length combinations. Elbows are available

in 90° and 45° conﬁgurations. Refer to Figure

19 on Page 17 for the 8DVLE45 and 8DVLE90

elbow dimensional speciﬁcations.

Where required, an adjustable DV length section

(8DVLAL) may be used to provide the installer

with an option in installing in tight and conﬁned

spaces or where the vent run made up of ﬁxed

length pieces develops a joint in a undesirable

location, or will not build up to the required

length. The 8DVLAL adjustable DV length

section has an effective length of from 1-1/2"

(38 mm) to 6-3/4" (171 mm). The 8DVLAL is

ﬁtted with a dimpled end (identical to a normal

vent section component) and a plain end with

3 pilot holes. Slip the dimpled end over the

locking channel end of a standard 8DVL vent

component the required distance and secure

with three screws.

Maintain a minimum 1" (26 mm) clearance

to combustible materials for all vertical ele-

ments. Clearances for all horizontal elements

are 3" (77 mm) on top, 1" (26 mm) on sides

and 1" (26 mm) on the bottom.

A. Frame ceiling opening—Use a plumb line

from the ceiling above the appliance to locate

center of the vertical run. Cut and/or frame an

opening, 13" x 13" (330 mm x 330 mm) inside

dimensions, about this center mark (Figure 16).

Figure 17

Blocking

Wall support

straps

(Plumber's tape)

8 feet (2.4 m)

Maximum

1" (26 mm)

minimum

clearance to

combustibles

Roof

Framing

Ceiling

Framing Plumb

Bob

Minimum

13”

(330 mm)

Minimum

13”

(330 mm)

Figure 18

Installation

900343-00J, 07/2023

Innovative Hearth Products

Montebello® DLX Series Direct-Vent Gas Fireplaces

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE

Push the vent component against the previous

section until it fully engages, then twist the

component clockwise running the dimples down

and along the incline channels until they seat at

the end of the channels. This seating position

is indicated by the alignment of the indents

into the entry slots as shown in Figure 17.

D. Install vertical ﬁrestop at ceiling—When

using 8" DV Lock, use 8DVLVF vertical ﬁrestop

at ceiling joists. If there is living space above

the ceiling level, the vertical ﬁrestop must be

installed on the bottom side of the ceiling. If attic

space is above the ceiling, the vertical ﬁrestop

must be installed on the top side of the joist.

Route the vent sections through the framed

opening and secure the ﬁrestop with 8d nails

or other appropriate fasteners at each corner.

Remember to maintain 1" (26 mm) clearance

to combustibles, framing members, and attic

or ceiling insulation when running vertical

chimney sections. Insulation shield (F4358)

is required and may be used to help maintain

the clearances indicated here. See installation

accessories on Page 31. The gap between the

vent pipe and a vertical ﬁrestop can be sealed

with non-combustible caulking.

E. Support the vertical vent run sections—

NOTE: Proper venting support is very important.

The weight of the vent must not be supported

by the ﬁreplace in any degree.

Support the vertical portion of the venting

system every 8 feet (2.4 m) above the ﬁreplace

vent outlet.

B. Attach vent components to appliance—

8" DV Lock (8DVL) direct-vent system compo-

nents are unitized concentric pipe components

featuring positive twist lock connections (see

Figure 17).

All of the appliances covered in this document

are ﬁtted with collars having locking inclined

channels. The dimpled end of the vent compo-

nents ﬁt over the appliance collar to create the

positive twist lock connection.

Joint Connection - 8” DV LOCK Direct Vent

components are engineered for easy twist

lock assembly. Eight indentations are located

on the female end of pipe and ﬁttings to slide

straight into the male end of the adjacent pipe

or ﬁtting, by orientating the eight indentations

so they match and slide into the eight entry

slots on the male ends.

Push the pipe sections completely together, then

twist lock one section clockwise approximately

one-quarter turn until the two sections are fully

locked (see Figure 17). Indentations on the

female end of black painted pipe and ﬁttings will

not be visible unless by examining the inside

of the female ends.

The unitized design of the 8" DV Lock com-

ponents will engage and seal both the inner

and outer pipe without the need for sealant or

screws. If desired a #6 x 1/2" screw may be

used at the joint, but it is not required as the

pipe will securely lock when twisted.

C. Attach vent components to each other—

Other vent sections may be added to the previ-

ously installed section in accordance with the

requirements of the vertical vent ﬁgures and

tables. To add another vent component to a

length of vent run, align the dimpled end over the

inclined channel end of the previously installed

section, adjusting the radial alignment until the

eight female end indentations are aligned with

the male end entry slots of the previous section.

Framing Dimensions for Roof

Inches (millimeters)

Pitch C D

0/12 13"

(330 mm)

13"

(330 mm)

6/12 13"

(330 mm)

15-1/2"

(394 mm)

12/12 13"

(330 mm)

20-1/2"

(541 mm)

Figure 20—Roof Framing

Figure 22

G. Continue installation of horizontal/inclined

sections—Continue with the installation of the

straight vent sections in horizontal/inclined run

as described in Step C. Install wall support

straps every 3 ft (914 mm) along horizontal/

inclined vent runs using conventional plumber’s

tape. See Page 19, Figure 26. It is very

important that the horizontal/inclined run

be maintained in a straight (no dips), slightly

elevated plane. The recommended incline is

approximately 1/4" per foot (20 mm per meter)

horizontal, in a direction away from the ﬁreplace.

The rise per foot run ratios that are smaller

are acceptable all the way down to at or near

level. Use a carpenter’s level to measure from

a constant surface and adjust the wall support

straps as necessary.

It is important to maintain the required clear-

ances to combustibles: 1" (26 mm) at all sides

for all vertical runs; and 3" (77 mm) at the

top, 1" (26 mm) at sides, and 1" (26 mm) at

the bottom for all horizontal/inclined runs.

H. Frame roof opening—Identify location for

vent at the roof. Cut and/or frame opening per

Roof Framing Chart (Figure 20).

One method of support is by utilizing ﬁeld

provided wall support straps (conventional

plumber's tape). Secure the plumber's tape to

the framing members with nails or screws. Strap

the tape around the vent, securing the ends of

the tape to the framing. If desired, sheet metal

screws #6 x 1/2" length may be used to secure

the wall support straps to the vent pipe. See

Figure 18 on Page 16.

F. Change vent direction to horizontal/inclined

run—At transition from or to a horizontal/in-

clined run, install the 8DVLE45 and 8DVLE90

elbows in the same manner as the straight vent

sections. Fully engage the inner and outer unit-

ized pipes at the bottom of the elbow. Rotate the

elbow in the desired direction. NOTE: Three (3)

holes are provided at the bottom of the elbows.

Secure the elbow in place with a minimum of

two (2) self tapping screws. The top of the elbow

will connect to straight lengths of 8" DV Lock

pipe by twist-locking the pieces together. See

Figure 17 on Page 16 and Figure 19.

Figure 19

If the vent system extends more than 5 feet (1.5

m) above the roof ﬂashing, stabilizers may be

necessary. Additional screws may be used at

section joints for added stability. Guide wires

may be attached to the joint for additional sup-

port on multiple joint conﬁgurations.

8DVLE45

(45° Elbow) 8DVLE90

(90° Elbow)

(153mm)

10"

(254mm)

Installation

900343-00J, 07/2023

Innovative Hearth Products

Montebello® DLX Series Direct-Vent Gas Fireplaces

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE

K. Install the vertical termination—The ﬁnal

step involves installation of the Vertical Termina-

tion. Extend the vent sections to the height as

shown in the "Vertical vent termination section"

on Page 8. The 8DVLVT Vertical Termination

(Figure 22) can be installed in the exact same

fashion as any other 8" DV Lock section. Align

the termination over the end of the previously

installed section, adjusting the radial alignment

until the entry slots on the last vent section

engage into the indents on the termination.

Push the termination down until it fully engages,

then twist the termination clockwise running the

dimples down and along the incline channels

until they seat at the end of the channels.

I. Install the roof ﬂashing—Extend the vent

sections through the roof structure. Install the

roof ﬂashing over the vent section and posi-

tion such that the vent column rises vertically

(use carpenters level) (Figure 21). Nail along

perimeter to secure ﬂashing or adjust rooﬁng to

overlap the ﬂashing edges at top and sides only

and trim where necessary. Seal the top and both

sides of the ﬂashing with waterproof caulking.

J. Install the storm collar—Install the storm

collar, supplied with the vertical termination,

over the vent/ﬂashing joint (see Figure 21).

Secure the storm collar in place on top of the

ﬂashing by sliding the tab through the mating

slot and folding over. Apply non-combustible

caulking or mastic around the circumference of

the joint to provide a water tight seal.

Figure 21

Storm

Collar

Flashing

Figure 25—Top Vent—Three Elbows

Table B

H + H1 Maximum V Minimum

feet (meter) feet (meter)

10 (3.1) 2.5 (0.762)

15 (4.65) 3.5 (1.06)

20 (6.2) 4.5 (1.37)

H + H1 = 20 feet (6.2 m) Max.

V + V1 + H + H1 = 40 ft. (12.4 m) Max.

V + V1 = 11 feet (3.3 meters) Min. for 40 in. units

V + V1 = 10.5 feet (3.2 meters) Min. for 45 in. units

Figure 24—Top Vent—Two 90 Degree Elbows (Corner Framing with Horizontal

Termination (8DVLHT))

Table A

H Maximum V Minimum

feet (meter) feet (meter)

10 (3.1) 2.5 (0.762)

15 (4.65) 3.5 (1.07)

20 (6.2) 4.5 (1.37)

V + V1 + H = 40 feet (12.4 meters) Max.

V + V1 = 11 feet (3.3 meters) Minimum for 40 in. units

V + V1 = 10.5 feet (3.2 meters) Minimum for 45 in. units

40 feet (12.2 meters)

Maximum

6 feet (1.8 meters)

Minimum

Figure 23—Top Vent—Straight

VERTICAL VENT FIGURES/TABLES

NOTES:

• 8" DV Lock (rigid vent pipe) is shown in

the ﬁgures.

• It is very important that the horizontal/

inclined run be maintained in a straight

(no dips), slightly elevated plane. The

recommended incline is approximately

1/4" per foot (20 mm per meter) horizontal,

in a direction away from the ﬁreplace. The

rise per foot run ratios that are smaller are

acceptable all the way down to at or near

level.

• 8DVLVF (8" DV Lock) vertical ﬁrestop must

be used anytime vent pipe passes through

a combustible ﬂoor or ceiling. 8DVLHF (8"

DV Lock) horizontal ﬁrestop must be used

anytime vent pipe passes through a com-

bustible wall.

• Two 45º elbows may be used in place of one

90º elbow. The same rise to run ratios, as

shown in the venting ﬁgures for 90º elbows,

must be followed if 45º elbows are used.

A Vent Restrictor, as shown in Figure 14 on Page

14, may need to be used in this application

Example: If 20 feet of (H) horizontal

vent run is needed, then 4-1/2 feet

minimum of (V) vertical vent will be

required.

A Vent Restrictor, as shown in

Figure 14 on Page 14, must be used

in this application.

Example: If 20 feet of (H+ H1) horizon-

tal vent run is needed, then 4-1/2 feet

minimum of (V) vertical vent will be

required.

A Vent Restrictor, as

shown in

Figure 14 on Page 14,

must be used in this

application.

Vertical

Firestop

(8DVLVF)

Vertical Firestop

(8DVLVF)

Vertical Firestop

(8DVLVF) Horizontal Firestop

(8DVLHF)

Installation

900343-00J, 07/2023

Innovative Hearth Products

Montebello® DLX Series Direct-Vent Gas Fireplaces

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE

Figure 26—Typical Horizontal Vent Installation

Support the vertical portion of the venting system

every 8 feet (2.4m) above the ﬁreplace vent outlet.

Vertical

Rise

Horizontal / Inclined Run

Support Bracket Spacing

Every 3 ft (914 mm)

Support

Brackets

Building

Support

Framing

Ceiling

Fireplace

Exterior

Wall

Exterior

Wall

2-1/2 Foot Vertical

Vent (min.)

E. Attach vent components to each other—

8” DV LOCK Direct Vent components are

engineered for easy twist lock assembly. Eight

indentations are located on the female end of

pipe and ﬁttings to slide straight into the male

end of the adjacent pipe or ﬁtting, by orientating

the eight indentations so they match and slide

into the eight entry slots on the male ends.

Push the pipe sections completely together, then

twist lock one section clockwise approximately

one-quarter turn until the two sections are fully

locked (see Figure 17 on Page 16). Indentations

on the female end of black painted pipe and

ﬁttings will not be visible unless by examining

the inside of the female ends.

F. Install vertical ﬁrestop at ceiling - When

using 8" DV Lock, use 8DVLVF vertical ﬁrestop

at ceiling joists. If there is living space above

the ceiling level, the vertical ﬁrestop must be

installed on the bottom side of the ceiling. If attic

space is above the ceiling, the vertical ﬁrestop

must be installed on the top side of the joist.

Route the vent sections through the framed

opening and secure the ﬁrestop with 8d nails

or other appropriate fasteners at each corner.

Remember to maintain 1" (26 mm) clearance

to combustibles, framing members, and attic

or ceiling insulation when running vertical

chimney sections. Insulation shield (F4358)

is required and may be used to help maintain

the clearances indicated here. See installation

accessories on Page 31. The gap between the

vent pipe and a vertical ﬁrestop can be sealed

with non-combustible caulking.

Remember to maintain 1" (26 mm) clearance

to combustibles, framing members, and attic

or ceiling insulation when running vertical

chimney sections.

Vertical Firestop

(8DVLVF)

8DVL 6/12/24/36/48

Vent Sections

8DVLHT

Termination

Shown

8DVLHT

Termination

Shown

8DVLE90

Elbow

Installation

900343-00J, 07/2023

Innovative Hearth Products

Montebello® DLX Series Direct-Vent Gas Fireplaces

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE

G. Support the vertical run sections—See

Step E on Page 16.

H. Change vent direction—At transition from or

to a horizontal/inclined run, install the 8DVLE45

and 8DVLE90 elbows in the same manner as the

straight vent sections. The elbows feature a twist

section to allow them to be routed about the

center axis of their initial collar section to align

with the required direction of the next vent run

element. Twist elbow sections in a clockwise

direction only so as to avoid the possibility

of unlocking any of the previously connected

vent sections (see Figure 17 on Page 18).

I. Continue installation of horizontal/inclined

sections—Continue with the installation of the

straight vent sections in horizontal/inclined run

as described in Step E on Page 16. Install wall

support straps every 3 feet (1914 mm) along

horizontal/inclined vent runs using conventional

plumber’s tape.

See Figure 26, It is very important that the

horizontal/inclined run be maintained in a

straight (no dips), slightly elevated plane. The

recommended incline is approximately 1/4"

per foot (20 mm per meter) horizontal, in a

direction away from the ﬁreplace. The rise per

foot run ratios that are smaller are acceptable

all the way down to at or near level.

It is important to maintain the required clear-

ances to combustibles: 1" (26 mm) at all sides

for all vertical runs; and 3" (77 mm) at the

top, 1" (26 mm) at sides, and 1" (26 mm) at

the bottom for all horizontal/inclined runs.

Use a carpenter’s level to measure from a

constant surface and adjust the wall support

straps as necessary.

HORIZONTAL (OUTSIDE WALL) TERMINATION

SYSTEM

See Figures 26–31 and their associated Horizon-

tal Vent tables that illustrate the various horizontal

venting conﬁgurations that are possible for use

with these appliances. 8" DV Lock pipe applica-

tions are shown in these Figures. A Horizontal

Vent table summarizes each system’s minimum

and maximum vertical and horizontal length

values that can be used to design and install the

vent components in a variety of applications.

The horizontal vent system terminates through

an outside wall. Building Codes limit or prohibit

terminating in speciﬁc areas. Refer to Figure 6

on Page 9 for location guidelines.

8" DV Lock direct-vent system components are

unitized concentric pipe components featuring

positive twist lock connection, (refer to Figure

17 on Page 16). All of the appliances covered

in this document are ﬁtted with collars having

locking inclined channels. The dimpled end of

the vent components ﬁt over the appliance col-

lar to create the positive twist lock connection.

A. Plan the vent run.

Analyze the vent routing and determine the

types and quantities of sections required

4-1/2" (114 mm), 10-1/2" (267 mm), 22-1/2" (572

mm), 34-1/2" (876 mm) and 46-1/2" (1181 mm) net

section lengths are available. It is recommended

that you plan the venting so that a joint does not

occur in the ceiling or roof joists. Allow for elbows

as indicated in Figure 20 on Page 17.

Maintain a minimum 1" (26 mm) clearance

to combustibles on the vertical sections.

Clearances for the horizontal runs are; 3"

(77 mm) on top, 1" (26 mm) on sides, and

1" (26 mm) at the bottom.

B. Frame exterior wall opening—Locate the

center of the vent outlet on the exterior wall

according to the dimensions shown in Figure

11 on Page 10. Cut and/or frame an opening,

15" x 13" (381 mm x 330 mm) inside dimen-

sions, with 9" above center and 7" below center.

C. Frame ceiling opening—If the vertical

route is to penetrate a ceiling, use plumb line

to locate the center above the appliance. Cut

and/or frame an opening, 13" x 13" (330 mm x

330 mm) inside dimensions, about this center

(refer to Figure 17 on Page 16).

D. Attach vent components to appliance—To

attach a vent component to the appliance collar,

align the dimpled end over the collar, adjust-

ing the radial alignment until the four locking

dimples are aligned with the inlets of the four

incline channels on the collar (refer to Figure

16 on Page 16).

Push the vent component against the collar

until it fully engages, then twist the component

clockwise, running the dimples down and along

the incline channels until they seat at the end of

the channels. The unitized design of the 8" DV

Lock components will engage and seal both the

inner and outer pipe elements with the same

procedure. Sealant and securing screws are

not required.

Horizontal terminations have been designed to perform in a wide range of weather condi-

tions. Our terminations meet or exceed industry standards.

When selecting the locations of your horizontal terminations, do not place the termination

where water from eaves and adjoining rooﬂines may create a heavy ﬂow of cascading water

onto the termination cap. If the cap must be placed where the possibility of cascading water

exists, it is the responsibility of the builder to direct the water away from the termination cap

by using gutters or other means.

Take care to carefully follow the installation instructions for the termination, including the

use of silicone caulking where required.

Siding

Stucco 1-1/4” Maximum Recess of

Square Termination into

Exterior Finishing Material

Exterior Surface of

Framing

5” to 8-1/2”

(127 to 216 mm)

Exterior Surface of Siding

Minimum wall thickness

5” (127 mm)

Interior Surface of

Finished Wall

Maximum wall thickness

6" (152 mm)

Maximum Extent of Vent

Run Sections to Exterior

Surface of Framing

Figure 28—Wall Thickness and Horizontal Termination Requirements

uFor wall thicknesses greater than

6" (152 mm), see Table 9

Figure 27—Installing the Horizontal Termination (8DVLHT)

13”

(330mm)

8-1/2”

(216 mm)

(165 mm)

15”

(381 mm)

NOTE: Centerline of Vent Piping is NOT

the Same as the Centerline of the

Framed Opening.

6 to 48” Vent Section,

Telescopic vent section.

Base of Appliance

3”

(77 mm)

1”

(26 mm)

1”

(26 mm)

6-1/2”

See Figure 11 on Page 12 for Minimum

Distance to Base of Appliance

To help minimize water inﬁltration it

is recommended that the horizontal

ﬁrestop (8DVLHF) be installed on the

exterior side of the wall.

6" (152 mm)

8DVLHT

Termination Shown

8DVLHT

Termination

Shown

8DVLHT

Termination

Shown

Last Vent Section. Use

8DVLAL Adjustable DV

Length, if necessary

Venting Connection and exterior Wall Recessing

of the Horizontal Termination (8DVLHT)

Installation

900343-00J, 07/2023

Innovative Hearth Products

Montebello® DLX Series Direct-Vent Gas Fireplaces

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE

J. Assemble vent run to exterior wall—If not

previously measured, locate the center of the

vent at the exterior wall. Prepare an opening as

described in Step B on Page 19. Assemble the

vent system to point where the terminus of the

last section is within 5" (127 mm) to 8-1/2" (216

mm) inboard of the exterior surface to which

the 8DVLHT horizontal termination is to be at-

tached, see Figure 29 and Table 9 on Page 21.

If the terminus of the last section is not within

this distance, use the adjustable DV length sec-

tion, 8DVLAL, as the last vent section. For wall

thicknesses greater than that shown in Figure

28, refer to Table 9 on Page 21. This table lists

the additional venting components needed (in

addition to the termination and adaptor) for a

particular range of wall thicknesses.

K. Install horizontal ﬁrestop at exterior wall

—When using the horizontal termination, install

8DVLHF horizontal ﬁrestop over the opening at

the exterior side of the framing, long side up,

with the 3" spacer clearance at the top as shown

in Figure 27, and nail into place.

(The horizontal ﬁrestop may also be installed

over the opening at the interior side of the

framing).

L. Install the Horizontal Termination (8DV-

LHT)— Before attaching the termination to

the exterior wall, run a bead of non-hardening

sealant around the termination's outside edges

so as to make a seal between the termination

and the wall.

With the HOT arrow on the termination pointing

up, slide the termination through the wall and

into the vent pipe and secure the termination

to the exterior wall with four wood screws.

The termination must slide over the mating vent

pipe a minimum of 1-1/4 inches. Use an 8DVLAL

Adjustable DV Length section if necessary to

complete the connection with the vent pipe. If

using the 8DVLAL, secure it using three (3) #8

x 1/2 sheet metal screws.

Secure the joint between the termination and

vent pipe by attaching the two metal strips

extending from the termination to the outer

vent pipe with two (2) #8 x 1/2 sheet metal

screws.

The horizontal termination must not be re-

cessed into the exterior wall or siding by more

than the 1-1/4" (32 mm) as shown in Figure 28.

IMPORTANT: The vent termination is hot

while in operation and for a period of time

following the use of the ﬁreplace. Young

children should be carefully supervised

when they are in the same area as a hot

termination.

La page charge ...

Astria Montebello DLX Mode d'emploi

Marque: Astria

Modèle: Montebello DLX

Catégorie: Cheminées

Taper: Mode d'emploi

Ce manuel convient également à

Montebello DLXCD

Télécharger le PDF

rapport

dans d''autres langues

English: Astria Montebello DLX Operating instructions

Astria Montebello DLX Mode d'emploi

Ce manuel convient également à

Astria Montebello DLX Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents