Denso FN01060 Manuel utilisateur

Taper
Manuel utilisateur
Manual for vehicle manufacturer
For Smart Key FOB
TYPE: FN01060
Details of contents Page
1.Description of manufacture 2
2. Technical description of Smart Key FOB 3
3.Outline of Smart Key FOB 4
DENSO KOREA ELECTRONICS CORPORATION
Dec. 15, 2020
1. Description of manufacturer
1.1 Trade mark
: N/A
1.2 Name and address of manufacturer
-Name : DENSO KOREA CORPORATION
-Address : 3, Cheomdansaneop-ro, Masanhappo-gu, Changwon-si,
Gyungsangnam-do, Korea
1.3 Name and address of applicant
-Name : DENSO KOREA CORPORATION
-Address : 3, Cheomdansaneop-ro, Masanhappo-gu, Changwon-si,
Gyungsangnam-do, Korea
2. Technical description of Smart Key FOB
2.1. Type
- Model : FN01060
2.2. Specifications of Electronic Key
- Nominal frequency : 433.92MHz
- Oscillator frequency (IC clock) : 16MHz
- Oscillator frequency (RF clock) : 27.6MHz
- Type of modulation : FSK/F1D
- Power Supply
- Nominal supply voltage : 3 VDC
- Type of Battery : One lithium battery
- Antenna : Built-in type (Fixed)
3. Outline of Smart Key FOB
Smart Key FOB is mainly used for locking or unlocking the doors of the vehicles.
Smart Key FOB detects signals when it reaches the vicinity of vehicle, and sends
signals using radio frequency.
Also, Smart Key FOB sends a radio wave signal while a button is pushed. When the
button is released, the radio wave signal is automatically off within 0.196 seconds.
When the button is depressed continuously, Smart Key FOB sends a signal for a
predetermined constant time.
This product sends a signal when the following buttons are pushed.
Transmitter IC
Actuator
Receiver
Subject for application
Installation in vehicle
Micom
Smart Key FOB
Control IC
LF Transmitter
433.92 MHz
125 kHz
Smart Key ECU
Panic button
for Panic Alarm
Unlock button
for unlocking the doors
Lock button
for locking the doors.
Backward button
for vehicle backward
Forward button
for vehicle forward
Remote Start button
for vehicle start
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation,
Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to
the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired
operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux
CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
(1) L’appareil ne doit pas produire de brouillage;
(2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
RF du FCC et IC d'exposition aux radiations: Cet équipement est conforme à l'exposition de
FCC et IC rayonnements RF limites é-tablies pour un environnement non contrôlé.
L’antenne pour ce transmetteur ne doit pas être même endroit avec d’autres émetteur sauf
conformément à FCC et IC procédures de produits Multi-émetteur.
FCC Part 15.19
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
FCC Part 15.21
Any changes or modifications (including the antennas) to this device that are not expressly
approved by the manufacturer may void the user's authority to operate the equipment.
FCC and IC RF Radiation Exposure Statement: This equipment complies with FCC and IC RF
Radiation exposure limits set forth for an uncontrolled environment.
This device and its antenna must not be co-located or operating in conjunction with any other
antenna or transmitter.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Denso FN01060 Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues