La-Z-Boy 10U515 Manuel utilisateur

Marque: La-Z-Boy

Modèle: 10U515

Taper: Manuel utilisateur

operating instructions

instrucciones de operación

instructions

Power Recliner with Headrest,

Power Recliner with Headrest and Lumbar,

Power Sofa with Headrest and

Power Sofa with Headrest and Lumbar Furniture

Sillón reclinable eléctrico con apoyacabezas, sillón

reclinable eléctrico con mecanismo lumbar y

apoyacabezas, sofá eléctrico con apoyacabezas, y sofá

eléctrico con mecanismo lumbar y de apoyacabezas

Fauteuil inclinable électrique avec repose-tête, fauteuil

inclinable électrique avec repose-tête et support lombaire,

canapé inclinable électrique avec repose-tête et canapé

inclinable électrique avec repose-tête et support lombaire

Congratulations!

You are now the proud owner of a

stat e-of-the-art Power Recliner with Headrest,

Power Recliner with Headrest and Lumbar,

Power Sofa with Headrest and Power Sofa with

Headrest and Lumbar furniture by La-Z-Boy.

You have just selected one of the

finest quality upholstered products

produced in the furniture industry,

backed by over 90 years of quality

manufacturing experience.

La-Z-Boy®is proud of our designs

and craftsmanship and knows you

will feel the same as you enjoy your

new furniture’s comfort and style.

Table of Contents

Important Safety Instructions ...................................... 4-5

Regulatory Compliance Statements....................................6

Power Recliner with Headrest Assembly Instructions.......8-9

Power Recliner with Headrest and Lumbar

Assembly Instructions................................................10-11

Power Sofa with Headrest Assembly Instructions..........12-15

Power Sofa with Headrest and Lumbar

Assembly Instructions................................................16-19

Battery Backup Assembly Instructions..................................20

Operating Instructions for Power Recliner with Headrest

with Standard Control Panel..................................................22-24

Operating Instructions for Power Recliner with Headrest

and Lumbar with Standard Control Panel..............................26-28

Operating Instructions for Power Sofa with Headrest

with Standard Control Panel..................................................30-32

Operating Instructions for Power Sofa with Headrest

and Lumbar with Standard Control Panel..............................34-36

Operating Instructions for Power Recliner with Headrest

with Optional Wireless Remote..............................................38-39

Operating Instructions for Power Recliner with Headrest

and Lumbar with Optional Wireless Remote.................40-41

Operating Instructions for Power Sofa with Headrest

with Optional Wireless Remote...................................42-43

Operating Instructions for Power Sofa with Headrest

and Lumbar with Optional Wireless Remote.....................44-45

Operating Instructions for Optional Wireless Remote.............46-49

Troubleshooting.....................................................................50-51

Furniture Placement Guide.................................................52

IMPORTANT

Read the safety and other instructions before using your

Power Recliner with Headrest, Power Recliner with Headrest and

Lumbar, Power Sofa with Headrest and Power Sofa with Headrest

and Lumbar furniture. Keep this manual for future reference. Disclaimer: The information and products featured in this manual may be

somewhat different from the product you purchased. La-Z-Boy reserves the right

to make substitutions that are equal in quality and performance.

– To reduce the risk of electric shock, serious injury or death:

• Liquids exposed to electricity pose an immediate risk of electric shock. Do not use this unit if the

power control is damaged, wet, in contact with or near spilled water or any liquid. Do not use the

unit if the button activation switch has been exposed to water or any liquid. Do not handle the

plug or remote control with wet hands.

• To prevent suffocation, keep plastic bags away from children.

• Keep cord out of the reach of children and pets that may cause damage.

• Do not attempt to disassemble, modify or service the product or motor; no serviceable parts are

inside. Only use genuine La-Z-Boy®parts and battery packs with the furniture. Contact your

La-Z-Boy dealer for service.

– To reduce the risk of burns, fire, electric shock, serious

injury or death:

• This product is intended for indoor residential use only.

• The back of the unit must be lifted for assembly. Please seek assistance if you are unable to lift

at least 45 pounds without strain.

• Keep upholstery away from flames or lit cigarettes. Upholstery may burn rapidly, with toxic gas and

thick smoke. Fires that begin elsewhere in a home may spread and involve upholstery. For your

safety, always use a properly installed smoke detector with working batteries.

• Unplug the power cord immediately if you detect strange odors or fumes coming from the unit.

• Plug directly into a wall outlet. Do not use an extension cord, adapter, surge protector or power strip.

• Do not attempt to disconnect the power plug by pulling the power cord. Always hold the power

plug and pull it out.

• Disconnect the power plug from outlet before cleaning, moving, servicing or when not in use for

an extended period of time.

• Closely supervise children and disabled persons using this product.

• This product has many moving parts, serious injury can occur if not used properly. Keep hands,

fingers and body parts away from the mechanism. To reduce the risk of head entrapment and

other injuries, keep children and pets away from openings and moving parts in and around furniture,

including the open area between a reclined back and an upright back on a reclining sofa.

• Do not place power supply underneath the power motion furniture.

• Do not place cord under carpet or in a location where it could become worn.

• Do not allow electrical cord to be pinched anywhere.

• Keep the electrical cord away from heat sources.

• Do not use this product where the cord may be a trip hazard.

• Provide a clear path for operation of the back and legrest. Place tables and area rugs at a distance

to allow the legrest to fully extend without rubbing or interference.

• Do not use this product if it is damaged. Do not use attachments or substitute parts.

• Never operate the unit with a damaged power supply, electrical cord, plug or connector. Check the

condition of the power supplies, electrical cords, plugs and connectors often.

DANGER

WARNING

Important Safety Instructions:

Important: Read these instructions thoroughly before using.

When assembling, do not plug in until directed in Operating Instructions.

Save These Instructions Save These Instructions

Important Safety Instructions:

Important: Read these instructions thoroughly before using.

When assembling, do not plug in until directed in Operating Instructions.

– To reduce the risk of burns, fire, electric shock, serious

injury or death:

• Do not operate the unit until the back is installed and locked.

• Sit down in the unit slowly. To avoid tip over, do not throw your weight against the back of the unit.

• Only the occupant should operate the unit. Never attempt to open the legrest by pulling on it.

• This unit is equipped with memory and home positions. Do not enter or exit the unit when the unit

is in motion.

• To safely exit the unit and prevent a tripping hazard, bring the back upright and close the legrest.

• Do not stand, sit or place extra weight on the arms, back or open legrest.

• This product may adversely affect medical devices. Do not use near people using or wearing

medical devices. Models with a wireless remote contain magnets in the cradle, which may

adversely affect medical devices.

• Users of medical devices should contact their health care provider before using this product. Do

not use this product if you have poor circulation, are immobile, or cannot sense heat, except as

directed by your health care provider.

• Do not use this product where aerosol (spray) products are being used or where oxygen is

being administered.

• This product is not intended to be used as a bed. Do not sleep in for an extended period.

• Double-insulated products are marked with the words “DOUBLE INSULATION” or “DOUBLE INSULATED”

and may include the symbol (square within a square). Do not attempt to ground these products,

which use two systems of insulation instead of grounding. Double-insulated products should be

serviced only by qualified service personnel, using replacement parts identical to the original parts.

• Before moving the product, disconnect the electrical plug from the wall outlet and secure the

mechanism to prevent unexpected opening or movement. Never move the product by the mechanism,

legrest, handle, reclining back, or swivel base.

• Power Motion Furniture with and without Headrest and Lumbar units are intended for a single

occupant not exceeding 300 pounds per seat. Do not operate an individual seat with more than

one occupant in or on any part of the individual seat.

• If you give this product to someone else, include this Operating Instructions manual.

– To reduce the risk of product damage:

• To prevent damage to the power supply, do not plug in until instructed.

• Never operate the unit except when it is on its base in the upright position.

• Gently press the buttons during operation and avoid hitting the buttons with pointed or hard objects.

• After 1 minute of continuous operation, allow the system to rest for 9 minutes.

• Only operate when no foreign object or obstacle will impede, interfere, or otherwise damage

the unit in any of its positions or while in motion.

NOTICE

WARNING

Regulatory Compliance Statements for

Furniture with Wireless Remote

(Page intentionally left blank)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy, and if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

Changes or modifications not expressly approved by the party responsible for compliance could void

the user’s authority to operate the equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may

cause undesired operation.

This device complies with Industry Canada’s license-exempt RSS standard(s). Operation is subject to

the following two conditions:

(1) This device may not cause interference, and

(2) This device must accept any interference, including interference that may cause

undesired operation of the device.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type

and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio

interference to other users, the antenna type and its gain must be so chosen that the equivalent

isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

Back Bracket

Body

Bracket

Body

Bracket

FIGURE 1FIGURE 2

FIGURE 4

FIGURE 5FIGURE 6

Electrical

Components Bag

120 Volt Power Cord

3. Install the back.

•Continue rotating the back at a slight angle, making sure the headrest and lumbar connections fall

between the rear seat and tailgate, and align the brackets on the back with the brackets on the

body (FIGURE 2)

•Lower the back onto the body, making sure the back and body brackets are completely engaged.

-To make sure the back is properly installed with both sets of back and body brackets

engaged, stand behind the chair and twist the back from side to side. If one or both sides

move out of position the brackets are not engaged (FIGURE 5). Remove the back and repeat

the steps above.

-If you are unable to install the back properly, contact your La-Z-Boy®dealer for assistance.

•Lock the brackets by using a screwdriver to push down the locking levers (FIGURE 3).

4. Remove the power supply from its packaging from the electrical components bag. Remove the power

supply and 120 volt power cord from the package.

5. Locate the motor connector behind the unit. Connect the motor connector to the power supply

connector. Align the connectors, push together until fully seated and close the locking cover to

secure the connection (FIGURE 6).

6. Connect the 120 volt power cord to the power supply (FIGURE 6). Do not plug in until instructed in

the operating instructions.

7. Proceed to the Battery Backup Assembly Instructions.

8. To remove the back, unplug the 120 volt power cord from the electrical outlet and disconnect the

power supply from the motor connector behind the unit. Reverse the Assembly Instructions steps.

When lifting the back up from the body, to lay across the arms, make sure to do so slowly and carefully

to prevent damage to the electrical connections.

Back and body brackets on this

side are not engaged. Remove

the back and reinstall.

Make this

connection

Power Supply*

Adjustable Headrest

Connection Brown

Motor Connector

Make this

connection

Tailgate Rear Seat

– To reduce the risk of injury:

• Do not operate the unit until the back is installed and locked.

• The back of the unit must be lifted for assembly. Please seek assistance if you are

unable to lift at least 45 pounds without strain.

WARNING

NOTICE: -- To reduce the risk of product damage:

• Do not plug in until instructed.

1. Once the furniture is unpacked, carefully remove the yellow electrical components bag from the body

bracket and set aside; depending on the product purchased, inside the bag are the power supply,

power cord, optional remote and three AAA batteries for the optional remote (FIGURE 1).

2. Make back electrical connections.

•Lay the back across the arms of the chair. Turn the locking levers, located on the brackets

attached to the back (one on each side), to a 90° angle (FIGURES 2 AND 3).

•Locate and identify the two electrical connections between the back and the body. The color of

the connectors varies by date of manufacture.

-The brown connectors on the right side (sitting) are for the adjustable headrest feature. One

connector routes from bottom of the back panel and the other between the rear seat and tailgate.

•Carefully rotate the back until the headrest actuator cable is able to reach the connector.

•Connect the adjustable headrest (FIGURE 4). Align the pins and sockets in the brown connectors,

push the connectors together and close the locking cover to secure the connection.

*Power supplies/connections

may vary by date of manufacture.

Back

Bracket

Locking

Lever

at a 90

Degree

Angle

Locked

Position

Power Recliner with Headrest

Assembly Instructions

Power Recliner with Headrest

Assembly Instructions

Power Rocking Recliner Style Featured

FIGURE 3

– To reduce the risk of injury:

• Do not operate the unit until the back is installed and locked.

• The back of the unit must be lifted for assembly. Please seek assistance if you are

unable to lift at least 45 pounds without strain.

WARNING

NOTICE: -- To reduce the risk of product damage:

• Do not plug in until instructed.

1. Once the furniture is unpacked, carefully remove the red electrical components bag from the body

bracket and set aside; depending on the product purchased, inside the bag are the power supply,

power cord, optional remotes and three AAA batteries for the optional remote (FIGURE 1).

2. Make back electrical connections.

•Lay the back across the arms of the chair. Turn the locking levers, located on the brackets

attached to the back (one on each side), to a 90° angle (FIGURES 2 AND 3).

•Locate and identify the electrical connection between the back and the body. The color of the

connectors varies by date of manufacture.

-The brown connectors on the right side (sitting) are for the adjustable headrest feature. One

connector routes from bottom of the back panel and the other between the rear seat and tailgate.

- The orange connectors on the left side (sitting) are for the adjustable lumbar feature. One connector

routes from bottom of the back panel and the other between the rear seat and tailgate.

•Carefully rotate the back until the headrest and lumbar actuator cables are able to reach the connectors.

•Connect the adjustable headrest (FIGURE 4). Align the pins and sockets in the brown connectors,

push the connectors together and close the locking cover to secure the connection.

•Connect the adjustable lumbar (FIGURE 4). Align the pins and sockets in the orange connectors,

push the connectors together and close the locking cover to secure the connection.

Power Recliner with Headrest

and Lumbar Assembly Instructions

3. Install the back.

•Continue rotating the back at a slight angle, making sure the headrest and lumbar connections fall

between the rear seat and tailgate, and align the brackets on the back with the brackets on the

body (FIGURE 2).

•Lower the back onto the body, making sure the back and body brackets are completely engaged.

-To make sure the back is properly installed with both sets of back and body brackets

engaged, stand behind the chair and twist the back from side to side. If one or both sides

move out of position the brackets are not engaged (FIGURE 5). Remove the back and repeat

the steps above.

-If you are unable to install the back properly, contact your La-Z-Boy®dealer for assistance.

•Lock the brackets by using a screwdriver to push down the locking levers (FIGURE 3).

4. Remove the power supply from its packaging from the electrical components bag. Remove the power

supply and 120 volt power cord from the package.

5. Locate the motor connector behind the unit. Connect the motor connector to the power supply

connector. Align the connectors, push together until fully seated and close the locking cover to

secure the connection (FIGURE 6).

6. Connect the 120 volt power cord to the power supply (FIGURE 6). Do not plug in until instructed in

the operating instructions.

7. Proceed to the Battery Backup Assembly Instructions.

8. To remove the back, unplug the 120 volt power cord from the electrical outlet and disconnect the

power supply from the motor connector behind the unit. Reverse the Assembly Instructions steps.

When lifting the back up from the body, to lay across the arms, make sure to do so slowly and carefully

to prevent damage to the electrical connections.

Body

Bracket

FIGURE 1FIGURE 2

FIGURE 4

FIGURE 5

Electrical

Components Bag

Back and body brackets on this

side are not engaged. Remove

the back and reinstall.

Adjustable Headrest

Connection Brown

Tailgate Rear Seat

Back

Bracket

Locking

Lever

at a 90

Degree

Angle

Locked

Position

Power Recliner with Headrest

and Lumbar Assembly Instructions

Back Bracket

Body

Bracket

Adjustable Lumbar

Connection Orange

FIGURE 6

120 Volt Power Cord

Make this

connection

Power Supply*

Motor Connector

Make this

connection

*Power supplies/connections

may vary by date of manufacture.

FIGURE 3

FIGURE 1

FIGURE 4

FIGURE 5

3. Install the back.

•Continue rotating the back at a slight angle, making sure the headrest connection falls between the

rear seat and tailgate, and align the brackets on the back with the brackets on the body (FIGURE 2).

•Lower the back onto the body, making sure the back and body brackets are completely engaged.

-To make sure the back is properly installed with both sets of back and body brackets

engaged, stand behind the chair and twist the back from side to side. If one or both sides

move out of position the brackets are not engaged (FIGURE 5). Remove the back and repeat

the steps above.

-If you are unable to install the back properly, contact your La-Z-Boy®dealer for assistance.

•Lock the brackets by using a screwdriver to push down the locking levers (FIGURE 3).

Back and body brackets on this

side are not engaged. Remove

the back and reinstall.

Adjustable Headrest

Connection Brown

– To reduce the risk of injury:

• Do not operate the unit until the back is installed and locked.

• The back of the unit must be lifted for assembly. Please seek assistance if you are

unable to lift at least 45 pounds without strain.

WARNING

NOTICE: -- To reduce the risk of product damage:

• Do not plug in until instructed.

1. Once the furniture is unpacked, carefully remove the yellow electrical components bag from the body

bracket and set aside; depending on the product purchased, inside the bag are the power supply,

power cord, optional remote and three AAA batteries for the optional remote (FIGURE 1).

2. Make back electrical connections.

•Lay the back across the arms of the chair. Turn the locking levers, located on the brackets

attached to the back (one on each side), to a 90° angle (FIGURES 2 AND 3).

•Locate and identify the electrical connections between the back and the body.

-The brown connectors on the right side (sitting) are for the adjustable headrest feature. One

connector routes from bottom of the back panel and the other between the rear seat and tailgate.

•Carefully rotate the back until the headrest actuator cable is able to reach the connector.

•Connect the adjustable headrest (FIGURE 4). Align the pins and sockets in the brown connectors,

push the connectors together and close the locking cover to secure the connection. Back

Bracket

Locking

Lever

at a 90

Degree

Angle

Locked

Position

Power Sofa with Headrest

Assembly Instructions

Power Sofa with Headrest

Assembly Instructions

Back Bracket

Body Bracket

FIGURE 2

Body

Bracket

Electrical

Components Bag

FIGURE 3

Tailgate Rear Seat

Power Sofa with Headrest

Assembly Instructions

Base Rail

Lock

Washer

Upper Jam Nut

Lower Jam Nut

Adjustable Glide

4. Adjust the glides to ensure a height that provides a clear path for operation of the legrest. Each glide is

attached to the base rail by one jam nut and one lock washer on top of the base rail, and one jam nut

on the bottom of the base rail.

•To extend the glide, loosen the upper jam nut by rotating clockwise. Turn the lower jam nut

clockwise to the desired height.

•Tighten the upper jam nut by rotating counterclockwise.

•Repeat steps one and two for each adjustable glide on the unit, if needed.

•Repeat this procedure, as necessary, to adjust the front height of the unit and level it.

5. Locate the motor connector, one behind each reclining seat (FIGURE 6). Connect the Y-cable to the

motor connectors and to the power supply.

•Align one motor connector to a long lead Y-cable connector, push the connectors together until

seated and close the locking cover to secure the connection (FIGURE 7). Repeat this for the other

motor connector and Y-cable long lead. Then align the short lead of the Y-cable to the power supply

connector, push the connectors together until seated and close the locking cover to secure the

connection (FIGURE 8).

6. Connect the 120 volt power cord to the power supply (FIGURE 9). Align the connector ends and

push together until seated. Do this for each power supply and 120 volt power cord included with the

furniture. Do not plug in until instructed in the Operating Instructions.

7. Proceed to the Battery Backup Assembly Instructions.

To Remove a Back:

1. Unplug the 120 volt power cord and disconnect the power supply from the Y-cable. Reverse the

Assembly Instructions steps. When lifting the back up from the body, to lay across the arms,

make sure to do so slowly and carefully to prevent damage to the electrical connections.

2. Repeat step 1 for the other side of the back.

FIGURE 6FIGURE 7

Motor Connector

FIGURE 8FIGURE 9

Y-Cable Long Leads

Make this

connection

Power Supply

Y-Cable Short Lead

Make these

connections

Make this

connection

Power Supply 120 Volt Power Cord

Power Sofa with Headrest

Assembly Instructions

Body

Bracket

FIGURE 1

FIGURE 4

FIGURE 5

Electrical

Components Bag

3. Install the back.

•Continue rotating the back at a slight angle, making sure the headrest and lumbar connections fall

between the rear seat and tailgate, and align the brackets on the back with the brackets on the

body (FIGURE 2).

•Lower the back onto the body, making sure the back and body brackets are completely engaged.

-To make sure the back is properly installed with both sets of back and body brackets

engaged, stand behind the chair and twist the back from side to side. If one or both sides

move out of position the brackets are not engaged (FIGURE 5). Remove the back and repeat

the steps above.

-If you are unable to install the back properly, contact your La-Z-Boy®dealer for assistance.

•Lock the brackets by using a screwdriver to push down the locking levers (FIGURE 3).

Back and body brackets on this

side are not engaged. Remove

the back and reinstall.

Adjustable Headrest

Connection Brown

– To reduce the risk of injury:

• Do not operate the unit until the back is installed and locked.

• The back of the unit must be lifted for assembly. Please seek assistance if you are

unable to lift at least 45 pounds without strain.

WARNING

NOTICE: -- To reduce the risk of product damage:

• Do not plug in until instructed.

1. Once the furniture is unpacked, carefully remove the red electrical components bag from the body

bracket and set aside; depending on the product purchased, inside the bag are the power supply,

power cord, optional remote and three AAA batteries for the optional remote (FIGURE 1).

2. Make back electrical connections.

•Lay the back across the arms of the chair. Turn the locking levers, located on the brackets

attached to the back (one on each side), to a 90° angle (FIGURES 2 AND 3).

•Locate and identify the orange and brown electrical connections between the back and the body.

-The brown connectors on the right side (sitting) are for the adjustable headrest feature. One

connector routes from bottom of the back panel and the other between the rear seat and tailgate.

-The orange connectors on the left side (sitting) are for the adjustable lumbar feature.

One connector routes from bottom of the back panel and the other between the rear seat and tailgate.

•Carefully rotate the back until the headrest and lumbar actuator cables are able to reach the connectors.

•Connect the adjustable headrest (FIGURE 4). Align the pins and sockets in the brown connectors,

push the connectors together and close the locking cover to secure the connection.

•Connect the adjustable lumbar (FIGURE 4). Align the pins and sockets in the orange connectors,

push the connectors together and close the locking cover to secure the connection.

Back

Bracket

Locking

Lever

at a 90

Degree

Angle

Locked

Position

Power Sofa with Headrest

and Lumbar Assembly Instructions

Power Sofa with Headrest

and Lumbar Assembly Instructions

Back Bracket

Body Bracket

FIGURE 2

FIGURE 3

Tailgate Rear Seat

Adjustable Lumbar

Connection Orange

Power Sofa with Headrest

and Lumbar Assembly Instructions

Base Rail

Lock

Washer

Upper Jam Nut

Lower Jam Nut

Adjustable Glide

4. Adjust the glides to ensure a height that provides a clear path for operation of the legrest. Each glide is

attached to the base rail by one jam nut and one lock washer on top of the base rail, and one jam nut

on the bottom of the base rail.

•To extend the glide, loosen the upper jam nut by rotating clockwise. Turn the lower jam nut

clockwise to the desired height.

•Tighten the upper jam nut by rotating counterclockwise.

•Repeat steps one and two for each adjustable glide on the unit, if needed.

•Repeat this procedure, as necessary, to adjust the front height of the unit and level it.

5. Locate the motor connector, one behind each reclining seat (FIGURE 6). Connect the Y-cable to the

motor connectors and to the power supply.

•Align one motor connector to a long lead Y-cable connector, push the connectors together until

seated and close the locking cover to secure the connection (FIGURE 7). Repeat this for the other

motor connector and Y-cable long lead. Then align the short lead of the Y-cable to the power supply

connector, push the connectors together until seated and close the locking cover to secure the

connection (FIGURE 8).

6. Connect the 120 volt power cord to the power supply (FIGURE 9). Do not plug in until instructed in

the Operating Instructions.

7. Proceed to the Battery Backup Assembly Instructions.

To Remove a Back:

1. Unplug the 120 volt power cord and disconnect the power supply from the Y-cable. Reverse the

Assembly Instructions steps. When lifting the back up from the body, to lay across the arms,

make sure to do so slowly and carefully to prevent damage to the electrical connections.

2. Repeat step 1 for the other side of the back.

FIGURE 6FIGURE 7

FIGURE 8FIGURE 9

Y-Cable Long Leads

Make this

connection

Power Supply

Y-Cable Short Lead

Make these

connections

Make this

connection

Power Supply 120 Volt Power Cord

Power Sofa with Headrest

and Lumbar Assembly Instructions

Motor Connector

Battery Backup

Assembly Instructions

NOTICE: Replace the power supply batteries every six months

and after each power failure use.

The performance of the built-in battery backup cannot be guaranteed. The backup system is

designed to return a reclined unit to the upright, closed position for exiting ease during a power

interruption. It is not intended to recline the unit. If you require continuing use during a power outage,

then you should purchase a separate battery backup system. Contact your La-Z-Boy®dealer for

more information.

When operating on battery backup the furniture operating speed is reduced. In addition, the

Memory I and Memory II programs and the USB charging port are disabled.

Always maintain constant, even pressure on the button when operating on battery backup to

reduce the energy consumption.

Replace the batteries every six months and after each power failure use.

The battery backup is located in the power supply and uses two 9-volt alkaline batteries (not included).

1. Unplug the 120 volt power cord from the electrical outlet, and disconnect the power supply

from the motor connector.

2. The battery compartment is located in the bottom of the power supply. Slide the battery cover

up to access the battery compartment.

3. Snap the connection caps on the battery terminals. Place the batteries in the power supply.

4. Slide the battery cover over the batteries.

5. Proceed to Operating Instructions.

Power

Supply

(2) 9-Volt

Alkaline Batteries

Power Supply Specifications:

Input: 100V-240V~, AC 50/60 Hz 1.5A

Output: 29V DC 2.5A

Battery

Cover

(Page intentionally left blank)

Operating Instructions for Power Recliner with

Headrest with Standard Control Panel

Right Side Sitting Featured; Left Side Sitting Opposite This View

Back toggle

Press the Back toggle rearward and hold to recline

the back. Or press it forward and hold to return

the back to the upright position. Release the button

to stop the back in any reclined position, or when

fully reclined or fully raised.

Headrest toggle

Press the Headrest toggle forward and hold to

rotate the headrest forward. Or press it rearward

and hold to return the headrest. Release the

button to stop the headrest in any position, or

when fully extended or fully retracted.

USB port

Rearward Forward

Home button

Press and release the

Home button to return

the furniture to the

upright, closed,

stored position.

Legrest toggle

Press the Legrest toggle rearward and hold

to extend the legrest and tilt the chair body

backward. Or press it forward and hold to close

the legrest and return the chair body. Release

the button to stop the legrest in any extended

position, or when fully raised or fully closed.

Memory I button

Memory II button

Press and release a

Memory button to

automatically move

the furniture to the

stored setting.

(pressing and holding

stores the setting)

– To reduce the risk of burns, electric shock,

serious injury or death:

• Liquids exposed to electricity pose an immediate risk of electric shock. Do not use this

unit if the power control is damaged, wet, in contact with or near spilled water or any

liquid. Do not use the unit if the button activation switch has been exposed to water or

any liquid. Do not handle the plug or remote control with wet hands.

DANGER

USB Output Specifications:

5 VDC, 1.0A

– To reduce the risk of electric shock, serious injury

or death:

• Liquids exposed to electricity pose an immediate risk of electric shock. Do not use this

unit if the power control is damaged, wet, in contact with or near spilled water or any liquid.

Do not use the unit if the button activation switch has been exposed to water or any liquid.

Do not handle the plug or remote control with wet hands.

• Do not attempt to disassemble, modify or service the product or motor; no serviceable

parts are inside. Only use genuine La-Z-Boy®parts and battery packs with the furniture.

Contact your La-Z-Boy dealer for service.

DANGER

– To reduce the risk of electric shock or serious injury:

• Plug directly into a wall outlet. Do not use an extension cord, adapter, surge protector or power strip.

• Sit down in the unit slowly. To avoid tip over, do not throw your weight against the back

of the unit. Move the unit into or out of the reclining position slowly, making sure that

no children or pets are in close proximity.

• The Power Rocking Recliner and Power Wall Recliner with Headrest units are intended for

a single occupant not exceeding 300 pounds per seat. Do not operate an individual seat

with more than one occupant in or on any part of the individual seat.

• To safely exit the unit and prevent a tripping hazard, bring the back upright and close the legrest.

WARNING

Operating Instructions for Power Recliner with

Headrest with Standard Control Panel

After 1 minute of continuous operation, allow the system to rest for 9 minutes.

NOTICE:

Only proceed after having followed the Assembly Instructions completely.

Operating Instructions for Furniture with a Control Panel:

Plug the power cord directly into a wall outlet. Make sure there is enough slack in the cord running

from the chair to the outlet to allow for rocking and reclining. Never stretch or strain a cord.

The power features are operated by the toggles on the Control Panel located on the outside

arm. Each feature has a dedicated toggle for independent operation of the feature, or

simultaneous operation of multiple features when more than one toggle is pressed.*

Press rearward the Back and Legrest toggle to increase the amount of recline or extension. Press

the toggle forward to retract the back and legrest.

Press the Headrest toggle forward to increase the amount of adjustment. Press the toggle rearward

to decrease the amount of adjustment.

The Control Panel also features Memory I, Memory II and Home buttons for personal, effortless

operation and added comfort. Two preferred recline settings may be stored for a more enjoyable

reclining experience. Press and release a stored Memory button (not holding for more than 2

seconds) and the furniture automatically moves to the stored setting. If no setting is stored, the

furniture will move to its home, or upright, closed and stored position. Press and release the Home

button and the furniture automatically moves to its home position.

A handy USB port for charging small personal electronic devices is located in the Control Panel to

keep your devices close at hand and ready for use at all times.

Unplug the power supply from the wall outlet if you are going to be away from your residence for

an extended period of time.

* When the furniture is powered by the 9-volt battery backup or the optional rechargeable lithium-ion

battery pack, only two features can be operated at the same time.

Operating Instructions for Power Recliner

with Headrest with Standard Control Panel

To Program and Use the Memory I or Memory II:

1. Adjust the furniture to the best and most comfortable position for you using the toggle buttons.

2. Press and hold the Memory I or Memory II button for three (or more) seconds.

3. Listen for the “beep” to indicate the setting was saved in memory.

• Memory I setting plays a single beep to indicate a successful save.

• Memory II setting plays a double beep to indicate a successful save.

• Three quick beeps play when the setting did not successfully save.

4. The next time you use your furniture, press and release either the Memory I or Memory II button

(not holding longer than two seconds) and the furniture automatically moves to the saved setting.

If no setting is stored, the furniture moves to its home, upright, closed and stored position instead.

Pressing a toggle or button on the control panel will stop the automatic motion of the furniture.

The furniture does not restart once the toggle or button is released. Another press of the Memory I

or Memory II button is required to start the furniture in motion again.

NOTE: All features start in motion upon a Memory button press if the feature is programmed to

recline or extend, except for the headrest.* When the headrest is programmed to extend, the headrest

does not start in motion until the back reaches approximately 40% recline, or its programmed recline

setting if set to less than 40% recline. This is done to guard against an undesirable positioning of the

head and neck when moving into the stored recline setting.

* Furniture must be plugged into a power outlet or powered by the optional rechargeable lithium-ion

battery pack for the Memory feature to function. This feature is disabled when powered by the 9-volt

battery backup. Additionally, when powered by the optional rechargeable lithium-ion battery pack,

only two features operate at the same time.

To Use the Home Button:

The Home button returns the back to its fully upright position and the legrest, headrest and lumbar

to the fully retracted and closed position.

Press and release the Home button. The furniture automatically starts in motion, moving the back,

legrest, headrest and lumbar back to the upright and retracted positions under full, normal power.

All motion stops if any toggle or button is pressed while the furniture is moving to home. The motion

does not resume when the toggle or button is released. Another press and release of the Home

button is required to restart the automatic home program.

NOTE: When the furniture is powered by the 9-volt battery back-up, the back and legrest move to

the home position first. Once the back and legrest are fully upright and retracted, then the headrest

will begin to move to the retracted, home position. When powered by the optional rechargeable lithium-

ion battery pack, the headrest will return to the Home position first, and then the back and legrest

return to Home.

To Use the USB Charging Port:

Plug the USB cable of a small portable electronic device into the USB charging port. Unplug the USB

cable from the charging port when charging is complete. The USB port is for charging only and does

not save or transfer data.

NOTE: When the furniture is operating on the 9-volt battery back-up in the power supply, the USB

charge port is disabled. When the furniture is powered by the optional rechargeable lithium-ion

battery pack, the USB port is enabled, as long as there is adequate charge.

(Page intentionally left blank)

Operating Instructions for Power Recliner with

Headrest and Lumbar with Standard Control Panel

Right Side Sitting Featured; Left Side Sitting Opposite This View

Headrest toggle

Press the Headrest toggle forward and hold to rotate

the headrest forward. Or press it rearward and hold

to return the headrest. Release the button to stop

the headrest in any position, or when fully extended

or fully retracted.

Back toggle

Press the Back toggle rearward and hold to recline

the chair back. Or press it forward and hold to return

the back to the upright position. Release the button

to stop the back in any reclined position, or when

fully reclined or fully raised.

USB port

– To reduce the risk of burns, electric shock,

serious injury or death:

• Liquids exposed to electricity pose an immediate risk of electric shock. Do not use this

unit if the power control is damaged, wet, in contact with or near spilled water or any

liquid. Do not use the unit if the button activation switch has been exposed to water or

any liquid. Do not handle the plug or remote control with wet hands.

DANGER

– To reduce the risk of electric shock, serious injury

or death:

• Liquids exposed to electricity pose an immediate risk of electric shock. Do not use this

unit if the power control is damaged, wet, in contact with or near spilled water or any liquid.

Do not use the unit if the button activation switch has been exposed to water or any liquid.

Do not handle the plug or remote control with wet hands.

• Do not attempt to disassemble, modify or service the product or motor; no serviceable

parts are inside. Only use genuine La-Z-Boy®parts and battery packs with the furniture.

Contact your La-Z-Boy dealer for service.

DANGER

– To reduce the risk of electric shock or serious injury:

• Plug directly into a wall outlet. Do not use an extension cord, adapter, surge protector or power strip.

• Sit down in the unit slowly. To avoid tip over, do not throw your weight against the back

of the unit. Move the unit into or out of the reclining position slowly, making sure that no

children or pets are in close proximity.

• The Power Rocking Recliner and Power Wall Recliner with Headrest and Lumbar units are

intended for a single occupant not exceeding 300 pounds per seat. Do not operate an

individual seat with more than one occupant in or on any part of the individual seat.

• To safely exit the unit and prevent a tripping hazard, bring the back upright and close the legrest.

WARNING

Operating Instructions for Power Recliner with

Headrest and Lumbar with Standard Control Panel

After 1 minute of continuous operation, allow the system to rest for 9 minutes.

NOTICE:

Only proceed after having followed the Assembly Instructions completely.

Operating Instructions for Furniture with a Control Panel:

Plug the power cord directly into a wall outlet. Make sure there is enough slack in the cord running

from the chair to the outlet to allow for reclining. Never stretch or strain a cord.

The power features are operated by the toggles on the Control Panel located on the outside

arm. Each feature has a dedicated toggle for independent operation of the feature, or

simultaneous operation of multiple features when more than one toggle is pressed. *

Press rearward the Back and Legrest toggle to increase the amount of recline or extension.

Press the toggle forward to retract the back and legrest.

Press the Headrest and Lumbar toggle forward to increase the amount of adjustment. Press the toggle

rearward to decrease the amount of adjustment.

The Control Panel also features Memory I, Memory II and Home buttons for personal, effortless operation

and added comfort. Two preferred recline settings may be stored for a more enjoyable reclining experience.

Press and release a stored Memory button (not holding for more than 2 seconds) and the furniture

automatically moves to the stored setting. If no setting is stored, the furniture will move to its home, or

upright, closed and stored position. Press and release the Home button and the furniture automatically

moves to its home position.

A handy USB port for charging small personal electronic devices is located in the cradle to keep

your devices close at hand and ready for use at all times.

Unplug the power supply from the wall outlet if you are going to be away from your residence for

an extended period of time.

* When the furniture is powered by the 9-volt battery backup or the optional rechargeable

lithium-ion pack, only two features can be operated at the same time.

Legrest toggle

Press the Legrest toggle rearward and hold to

extend the legrest and tilt the chair body backward.

Or press it forward and hold to close the legrest

and return the chair body. Release the button to

stop the legrest in any extended position, or when

fully raised or fully closed.

Rearward

USB Output Specifications:

5 VDC, 1.0A

Forward

Home button

Press and release the

Home button to return

the furniture to the

upright, closed,

stored position.

Memory I button

Memory II button

Press and release a

Memory button to

automatically move

the furniture to the

stored setting.

(pressing and holding

stores the setting)

Lumbar toggle

Press the Lumbar toggle forward and hold to

increase the lumbar intensity. Or press it rearward

and hold to decrease lumbar intensity. Release the

button to stop the lumbar in any position, or when

fully extended or fully retracted.