MikroTik RB5009UG+S+IN Routers and Wireless Manuel utilisateur

Marque: MikroTik

Modèle: RB5009UG+S+IN Routers and Wireless

Taper: Manuel utilisateur

RB5009UG+S+IN

Safety Information:

Before you work on any MikroTik equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for

preventing accidents. The installer should be familiar with network structures, terms, and concepts.

Use only the power supply and accessories approved by the manufacturer, and which can be found in the original packaging of this product.

This equipment is to be installed by trained and qualified personnel, as per these installation instructions. The installer is responsible for making

sure, that the Installation of the equipment is compliant with local and national electrical codes. Do not attempt to disassemble, repair, or modify

the device.

This product is intended to be installed indoors. Keep this product away from water, fire, humidity, or hot environments.

We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate

at your own risk!

In the case of device failure, please disconnect it from power. The fastest way to do so is by unplugging the power plug from the power outlet.

This is a Class A product. In a domestic environment, this product might cause radio interference in which case the user might be required to take

adequate measures

Electric shock hazard. This equipment is to be serviced by trained personnel only

Setup

Make sure your ISP is allowing hardware change and will automatically issue an IP address.

Connect your ISP cable to the first Ethernet port.

Connect your PC to any of the Ethernet ports.

Connect the device to the power source.

Use a Web browser or WinBox to connect to the default IP address of 192.168.88.1 from any port, with the username and no password.

admin

If IP is not available, download WinBox from our webpage and use it to connect through MAC address.

Update RouterOS software to the latest version, make sure that the device has an internet connection.

If the device does not have an internet connection update software by downloading the latest version from our webpagehttps://mikrotik.com

/download

Find the latest software and choose your packages.

To get the architecture type of your device model, open WinBox, WebFig go to (System/Resources).

Download packages to the PC and upload them to the WinBox, WebFig, (Files) menu, and reboot the device.

Set up your password to secure the device.

Powering

The power consumption under maximum load can reach 20 W. The device accepts power from the power jack or from the first Ethernet port:

Direct-input power jack (5.5 mm outside and 2 mm inside, female, pin positive plug) accepts 24-57 V DC.

The First Ethernet port accepts Power over Ethernet 24-57 V DC.

Connecting to a POE Adapter:

Connect the Ethernet cable from the device to the POE port of the POE adapter.

Connect an Ethernet cable from your LAN to the LAN port of the POE adapter, please mind arrows for data and power flow.

Connect the power cord to the adapter, and then plug the power cord into a power outlet.

Configuration

Once logged in, we recommend clicking the "Check for updates" button in the QuickSet menu, as updating your RouterOS software to the latest version

ensures the best performance and stability. For wireless models, please make sure you have selected the country where the device will be used, to

conform with local regulations.

RouterOS includes many configuration options in addition to what is described in this document. We suggest starting here to get yourself accustomed to

the possibilities: . In case an IP connection is not available, the Winbox tool ( ) can be used to connect to the MAC https://mt.lv/help https://mt.lv/winbox

address of the device from the LAN side (all access is blocked from the Internet port by default).

For recovery purposes, it is possible to boot the device for reinstallation, see section .Buttons and jumpers

Mounting

The device is designed to use indoors and it can be mounted on the wall, or it can be placed on the desktop.

Find the designed mounting holes on both sides of the device, as shown in the picture;

Use provided screws to secure device to the wall;

Based on the wall material you can use a drill bit and provided dowels.

The device has no protection from water contamination, please ensure the placement of the device in a dry and ventilated environment.

We recommend Cat6 cables for our devices.

The mounting and configuration of this device should be done by a qualified person.

Rackmount

If desired placement is rackmount, additional brackets can be purchased separately:

RB5009 rackmount kit K-79

Extension slots and ports

Product code RB5009UG+S+IN

CPU 88F7040 1.4 GHz

CPU architecture ARM 64bit

CPU core count 4

Size of RAM 1 GB

RAM type DDR4

Storage 1 GB, NAND

Number of 1G Ethernet ports 7

Number of 2.5G Ethernet ports 1

Number of 10G SFP+ ports 1

USB port 1 (3.0 type A)

Operating system RouterOS (License level 5)

Switch chip model 88E6393

Dimensions 220 x 125 x 22 mm

Operating temperature -40°C to +60°C

Buttons and jumpers

The RouterBOOT reset button has the following functions. Press the button and apply the power, then:

Release the button when the green LED starts flashing, to reset RouterOS configuration to defaults.

Release the button after LED is no longer lit (~20 seconds) to cause a device to look for Netinstall servers (required for reinstalling RouterOS over

the network).

Regardless of the above option used, the system will load the backup RouterBOOT loader if the button is pressed before power is applied to the device.

Useful for RouterBOOT debugging and recovery.

Accessories

The package includes the following accessories that come with the device:

ADAPT1_EU/US Switching Power Supply 24V 1.5A 36W

SET1_ K-55 fastening set

PAD1_ 4 pcs Pad D=7; H=1.5 mm, black, one side adhesive 3M988T

Please visit wiki pages for MikroTik SFP module compatibility table: https://wiki.mikrotik.com/wiki/MikroTik_wired_interface_compatibility

Operating system support

The device supports RouterOS software version 7.0.5. The specific factory-installed version number is indicated in the RouterOS menu /system resource.

Other operating systems have not been tested.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. 
These limits are designed to provide reasonable protection against harmful interference in a commercial installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction 
manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference 
in which case the user will be required to correct the interference at his own expense
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this
equipment.
This  device  complies  with  Part  15  of  the  FCC  Rules.  Operation  is  subject  to  the  following  two  conditions:  (1)  This  device  may  not  cause  harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This unit was tested with shielded cables on the peripheral devices. Shielded cables must be used with the unit to ensure compliance.
Innovation, Science and Economic Development Canada
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt
RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference,
including interference that may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique
Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: 1) L’appareil ne doit pas produire
de brouillage; 2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
This ClassA digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [A] est conforme à la norme NMB-003 du Canada.
CAN ICES-003 (A) / NMB-003 (A)
CE Declaration of Conformity
BG
С настоящото Mikrotīkls SIA декларира, че този тип радиосъоръжение RB5009UG+S+IN е в съответствие с Директива 2014/30/ЕС. 
Цялостният текст на ЕС декларацията за съответствие може да се намери на следния интернет адрес:https://mikrotik.com/products
CS Tímto Mikrotīkls SIA prohlašuje, že typ rádiového zařízení RB5009UG+S+IN je v souladu se směrnicí 2014/30/EU. Úplné znění EU prohlášení o 
shodě je k dispozici na této internetové adrese:https://mikrotik.com/products
DA Hermed erklærer Mikrotīkls SIA, at radioudstyrstypen RB5009UG+S+IN er i overensstemmelse med direktiv 2014/30/EU. EU-
overensstemmelseserklæringens fulde tekst kan findes på følgende internetadresse:https://mikrotik.com/products
DE Hiermit erklärt Mikrotīkls SIA, dass der Funkanlagentyp RB5009UG+S+IN der Richtlinie 2014/30/EU entspricht. Der vollständige Text der EU-
Konformitätserklärung ist unter der folgenden Internetadresse verfügbar:https://mikrotik.com/products
EL Με την παρούσα ο/η Mikrotīkls SIA, δηλώνει ότι ο ραδιοεξοπλισμός RB5009UG+S+IN πληροί την οδηγία 2014/30/ΕΕ. Το πλήρες κείμενο της 
δήλωσης συμμόρφωσης ΕΕ διατίθεται στην ακόλουθη ιστοσελίδα στο διαδίκτυο:https://mikrotik.com/products
EN Hereby, Mikrotīkls SIA declares that the radio equipment type RB5009UG+S+IN is in compliance with Directive 2014/30/EU. The full text of the EU 
declaration of conformity is available at the following internet address:https://mikrotik.com/products
ES Por la presente, Mikrotīkls SIA declara que el tipo de equipo radioeléctrico RB5009UG+S+IN es conforme con la Directiva 2014/30/UE. El texto 
completo de la declaración UE de conformidad está disponible en la dirección Internet siguiente:https://mikrotik.com/products
ET Käesolevaga deklareerib Mikrotīkls SIA, et käesolev raadioseadme tüüp RB5009UG+S+IN vastab direktiivi 2014/30/EL nõuetele. ELi 
vastavusdeklaratsiooni täielik tekst on kättesaadav järgmisel internetiaadressil:https://mikrotik.com/products
FI Mikrotīkls SIA vakuuttaa, että radiolaitetyyppi RB5009UG+S+IN on direktiivin 2014/30/EU mukainen. EU-vaatimustenmukaisuusvakuutuksen 
täysimittainen teksti on saatavilla seuraavassa internetosoitteessa:https://mikrotik.com/products
FR Le soussigné, Mikrotīkls SIA, déclare que l'équipement radioélectrique du type RB5009UG+S+IN est conforme à la directive 2014/30/UE. Le texte 
complet de la déclaration UE de conformité est disponible à l'adresse internet suivante:https://mikrotik.com/products
HR Mikrotīkls SIA ovime izjavljuje da je radijska oprema tipa RB5009UG+S+IN u skladu s Direktivom 2014/30/EU. Cjeloviti tekst EU izjave o sukladnosti 
dostupan je na sljedećoj internetskoj adresi:https://mikrotik.com/products

HU Mikrotīkls SIA igazolja, hogy a RB5009UG+S+IN típusú rádióberendezés megfelel a 2014/30/EU irányelvnek. Az EU-megfelelőségi nyilatkozat 
teljes szövege elérhető a következő internetes címen:https://mikrotik.com/products
IT Il fabbricante, Mikrotīkls SIA, dichiara che il tipo di apparecchiatura radio RB5009UG+S+IN è conforme alla direttiva 2014/30/UE. Il testo completo 
della dichiarazione di conformità UE è disponibile al seguente indirizzo Internet:https://mikrotik.com/products
IS Hér með lýsir Mikrotīkls SIA því yfir að RB5009UG+S+IN er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 2014/30/EU.Fullur 
texti ESB samræmisyfirlýsingar er að finna á eftirfarandi veffangi:https://mikrotik.com/products
LT Aš, Mikrotīkls SIA, patvirtinu, kad radijo įrenginių tipas RB5009UG+S+IN atitinka Direktyvą 2014/30/ES. Visas ES atitikties deklaracijos tekstas 
prieinamas šiuo interneto adresu:https://mikrotik.com/products
LV Ar šo Mikrotīkls SIA deklarē, ka radioiekārta RB5009UG+S+IN atbilst Direktīvai 2014/30/ES. Pilns ES atbilstības deklarācijas teksts ir pieejams šādā 
interneta vietnē:https://mikrotik.com/products
MT B'dan, Mikrotīkls SIA, niddikjara li dan it-tip ta' tagħmir tar-radju RB5009UG+S+IN huwa konformi mad-Direttiva 2014/30/UE. It-test kollu tad-
dikjarazzjoni ta' konformità tal-UE huwa disponibbli f'dan l-indirizz tal-Internet li ġej:https://mikrotik.com/products
NL Hierbij verklaar ik, Mikrotīkls SIA, dat het type radioapparatuur RB5009UG+S+IN conform is met Richtlijn 2014/30/EU. De volledige tekst van de EU-
conformiteitsverklaring kan worden geraadpleegd op het volgende internetadres:https://mikrotik.com/products
NO Mikrotīkls SIA erklærer herved at utstyret RB5009UG+S+IN er i samsvar med de grunnleggende krav og øvrige relevante krav i direktiv 2014/30
/EU. Den fulle teksten til EU-samsvarserklæringen er tilgjengelig på følgende internettadresse:https://mikrotik.com/products
PL Mikrotīkls SIA niniejszym oświadcza, że typ urządzenia radiowego RB5009UG+S+IN jest zgodny z dyrektywą 2014/30/UE. Pełny tekst deklaracji 
zgodności UE jest dostępny pod następującym adresem internetowym:https://mikrotik.com/products
PT O(a) abaixo assinado(a) Mikrotīkls SIA declara que o presente tipo de equipamento de rádio RB5009UG+S+IN está em conformidade com a 
Diretiva 2014/30/UE. O texto integral da declaração de conformidade está disponível no seguinte endereço de Internet:https://mikrotik.com/products
RO Prin prezenta, Mikrotīkls SIA declară că tipul de echipamente radio RB5009UG+S+IN este în conformitate cu Directiva 2014/30/UE. Textul integral 
al declaraiei UE de conformitate este disponibil la următoarea adresă internet:https://mikrotik.com/products
SK Mikrotīkls SIA týmto vyhlasuje, že rádiové zariadenie typu RB5009UG+S+IN je v súlade so smernicou 2014/30/EÚ. Úplné EÚ vyhlásenie o zhode je 
k dispozícii na tejto internetovej adrese:https://mikrotik.com/products
SL Mikrotīkls SIA potrjuje, da je tip radijske opreme RB5009UG+S+IN skladen z Direktivo 2014/30/EU. Celotno besedilo izjave EU o skladnosti je na 
voljo na naslednjem spletnem naslovu:https://mikrotik.com/products
SV Härmed försäkrar Mikrotīkls SIA att denna typ av radioutrustning RB5009UG+S+IN överensstämmer med direktiv 2014/30/EU. Den fullständiga 
texten till EU-försäkran om överensstämmelse finns på följande webbadress:https://mikrotik.com/products
(EN) Technical Specifications / (DE) Technische Spezifikationen / (FR) Spécifications 
techniques /
(IT) Specifiche tecniche / (ES) Especificaciones técnicas / (RU) Технические характеристики:
Product Power Input Options Power Adapter Output Specification Degrees of protection provided by enclosure (IP Code) Operating Temperature
Voltage Current
DC Jack = 12-57 V DC
PoE In Ethernet Port = 18-57 V DC
2-pin terminal = 12-57 V DC
24 V 1.5 A IP20 40°..+60°C-