Whirlpool WDT751SAPZ Manuel utilisateur

Marque: Whirlpool

Modèle: WDT751SAPZ

Catégorie: Lave-vaisselle

Taper: Manuel utilisateur

W11532445D

PLASTIC TUB DISHWASHER OWNER'S MANUAL

GUIDE D’UTILISATION DU LAVE-VAISSELLE AVEC

CUVE EN PLASTIQUE

Table of Contents/Table des matières

DISHWASHER SAFETY ....................................................2

Dishwasher Safety .........................................................2

DISHWASHER MAINTENANCE AND CARE .........................4

User-Maintenance Instructions .........................................4

INSTALLATION REQUIREMENTS.......................................5

Tools and Parts .............................................................5

Location Requirements ...................................................7

Cabinet Opening Dimensions ...........................................7

Drain Requirements .......................................................7

Water Supply Requirements.............................................8

Electrical Requirements ..................................................8

INSTALLATION INSTRUCTIONS ........................................8

Before You Begin...........................................................9

Prepare Cabinet Opening – New Utilities.............................9

Install Optional Moisture Barrier (Recommended for Wood

Countertops).................................................................9

Electrical Connection .................................................... 10

Prepare Dishwasher ..................................................... 10

Remove Access Panel .................................................. 11

Connect Water Line to Fill Valve...................................... 12

Connect Fill Hose to Fill Valve......................................... 13

Drain Hose Connection ................................................. 13

Power Cord Connection ................................................ 13

Install Door Handle (on some models) .............................. 15

Place Dishwasher in Cabinet .......................................... 16

Choose Anchor Attachment Method................................. 17

Final Installation Check ................................................. 17

Secure Dishwasher in Cabinet Opening............................ 19

Direct Wire Connection ................................................. 19

Connect Water Line to House Shutoff Valve....................... 21

Connect Drain Hose ..................................................... 21

Complete Installation .................................................... 23

Install Access Panel ..................................................... 24

Check Operation ..................................................................... 24

If Dishwasher Does Not Operate ..................................... 25

Additional Tips............................................................. 25

SÉCURITÉ DU LAVE-VAISSELLE..................................... 26

Sécurité du lave-vaisselle .............................................. 26

ENTRETIEN ET RÉPARATION DU LAVE-VAISSELLE .......... 28

Instructions d’entretien pour l’utilisateur ............................ 28

EXIGENCES D’INSTALLATION ........................................ 29

Outils et pièces............................................................ 29

Exigences d’emplacement ............................................. 31

Dimensions de l’ouverture de l’armoire ............................. 32

Exigences d’évacuation................................................. 32

Spécifications de l’alimentation en eau ............................. 32

Spécifications électriques .............................................. 32

INSTRUCTIONS D’INSTALLATION ................................... 33

Avant de commencer.................................................... 33

Préparation de l’emplacement – nouvelles unités................ 34

Installer la barrière anti-humidité en option (recommandée

pour les comptoirs en bois) ............................................ 34

Raccordement électrique............................................... 35

Préparation du lave-vaisselle.......................................... 35

Retrait du panneau d’accès............................................ 36

Branchement de l’arrivée d’eau à la valve de distribution ...... 37

Branchement du tuyau de distribution à la valve de

distribution ................................................................. 38

Raccord du tuyau de vidange ......................................... 38

Branchement du câble électrique .................................... 39

Installer la poignée de porte (sur certains modèles) ............. 40

Placer le lave-vaisselle dans l’armoire .............................. 41

Choix de l’option de fixation............................................ 42

Vérification finale de l’installation..................................... 42

Fixation du lave-vaisselle dans l’ouverture d’encastrement

de l’armoire ................................................................ 44

Méthode de raccordement direct ..................................... 44

Branchement de l’arrivée d’eau au robinet d’arrêt de la

maison ...................................................................... 46

Raccordement du tuyau de vidange ................................. 46

Fin de l’installation ....................................................... 48

Installation du panneau d’accès ...................................... 49

Vérification du fonctionnement ............................................... 49

Si le lave-vaisselle ne fonctionne pas ............................... 50

Conseils supplémentaires.............................................. 50

DISHWASHER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.” These

words mean:

DANGER You can be killed or seriously injured if you don't

immediately follow instructions.

WARNING You can be killed or seriously injured if you don’t follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: When using your dishwasher, follow basic precautions, including the following:

nRead all instructions before using the dishwasher.

nUse the dishwasher only for its intended function.

nUse only detergents or wetting agents recommended for

use in a dishwasher and keep them out the reach of

children.

nWhen loading items to be washed:

1. Locate sharp items so that they are not likely to damage

the door seal; and

2. Load sharp knives with the handles up to reduce the

risk of cut-type injuries.

nDo not wash plastic items unless they are marked

"dishwasher safe" or the equivalent. For plastic items not so

marked, check the manufacturer's recommendations.

nDo not touch the heating element during or immediately

after use.

nDo not operate your dishwasher unless all enclosure

panels are properly in place.

nDo not tamper with controls.

nDo not abuse, sit on, or stand on the door or dish racks of

the dishwasher.

nTo reduce the risk of injury, do not allow children to play in

or on a dishwasher.

nUnder certain conditions, hydrogen gas may be produced

in a hot-water system that has not been used for two weeks

or more. HYDROGEN GAS IS EXPLOSIVE. If the hot-

water system has not been used for such a period, before

using the dishwasher, turn on all hot-water faucets and let

the water flow from each for several minutes. This will

release any accumulated hydrogen gas. As the gas is

flammable, do not smoke or use an open flame during this

time.

nRemove the door to the washing compartment when

removing an old dishwasher from service or discarding it.

nDo not use replacement parts that have not been

recommended by the manufacturer (e.g. parts made at

home using a 3D printer).

SAVE THESE INSTRUCTIONS

GROUNDING INSTRUCTIONS

qFor a grounded, cord-connected dishwasher:

The dishwasher must be grounded. In the event of a

malfunction or breakdown, grounding will reduce the risk of

electric shock by providing a path of least resistance for

electric current. The dishwasher is equipped with a cord

having an equipment-grounding conductor and a grounding

plug. The plug must be plugged into an appropriate outlet

that is installed and grounded in accordance with all local

codes and ordinance.

WARNING: Improper connection of the equipment-grounding

conductor can result in a risk of electric shock.

Check with a qualified electrician or service representative if

you are in doubt whether the dishwasher is properly grounded.

Do not modify the plug provided with the dishwasher; if it will not

fit the outlet, have a proper outlet installed by a qualified

electrician.

qFor a permanently connected dishwasher:

The dishwasher must be connected to a grounded metal,

permanent wiring system, or an equipment-grounding

conductor must be run with the circuit conductors and

connected to the equipment-grounding terminal or lead on

the dishwasher.

SAVE THESE INSTRUCTIONS

WARNING

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Doing so can result in serious injury or cuts.

DISHWASHER MAINTENANCE

AND CARE

User-Maintenance Instructions

Cleaning the Exterior

Clean the exterior of the dishwasher with only a soft, damp cloth

and mild detergent. If your dishwasher has a stainless steel

exterior, it may have a coating that is resistant to fingerprints.

Avoid using abrasive cleaning products on the exterior of the

dishwasher.

Cleaning and Maintaining the Interior

Many detergents may leave white spots or a white residue on

dishware and on the interior of the dishwasher. Over time this

residue can become unsightly and could affect dishwasher

performance. Use of a dishwasher cleaning product such as

affresh®† Dishwasher Cleaner can help to remove the residue.

Monthly use of affresh® Dishwasher Cleaner is recommended to

help maintain the dishwasher. Follow package directions.

Another method to remove white residue is to use a vinegar rinse.

However, vinegar is an acid and using it too often could damage

your dishwasher.

Place (do not pour) 2 cups (500 mL) of white vinegar in a glass or

dishwasher-safe measuring cup on the bottom rack. Run the

dishwasher through a complete washing cycle using an air-dry or

an energy-saving dry option. Do not use detergent. Vinegar will

mix with the wash water.

NOTE: We recommend the use of high-quality, premeasured

detergent tablets or packs and the use of rinse aid for dishwasher

cleaning and daily care.

If you have a drain air gap, check and clean it if the dishwasher is

not draining well.

To Reduce Risk of Property Damage During

Vacation or Extended Time Without Use

nIf the dishwasher will not be used during the summer months,

turn off the water and power supply to the dishwasher.

nMake sure the water supply lines are protected against

freezing conditions. Ice formations in the supply lines can

increase water pressure and cause damage to your

dishwasher or home. Damage from freezing is not covered by

the warranty.

nWhen storing your dishwasher in the winter, avoid water

damage by having your dishwasher winterized by authorized

service personnel.

Cleaning the Filters

It is very easy to remove and maintain the filters. The chart below

shows the recommended cleaning frequency.

Recommended Time Interval to Clean Your Filter

Number of

loads per

week

If you only

scrape

before

loading*

If you scrape

and rinse

before

If you wash

before

8–12 Every two

months Every four

months Once per

year

4–7 Every two

months Once per

year Once per

year

1–3 Twice per

year Once per

year

*Manufacturer's recommendation: This practice will conserve the

water and energy that you would have used to prepare your

dishes. This will also save you time and effort.

Very Hard Water

If you have hard water (above 15 grains), clean your filter at least

once per month. Building up of white residue on your dishwasher

indicates hard water. For tips on removing spots and stains, see

the online “Troubleshooting” section.

NOTE: Online references can be found in the Quick Start Guide.

Filter Removal Instructions

1. Turn the upper filter assembly 1/4 turn counterclockwise and

lift out.

2. Separate the upper filter assembly by gently pulling apart.

3. Clean the filters as shown.

A. Locating tab

Cleaning Instructions

IMPORTANT: Do not use wire brush, scouring pad, etc., as they

may damage the filters.

Rinse filter under running water until most soils are removed. If

you have hard-to-remove soils or calcium deposits from hard

water, a soft brush may be required.

✝affresh®is a registered trademark of Whirlpool, U.S.A.

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the recommended tools and parts before starting

installation. Read and follow the instructions provided with any

tools listed here.

Tools Needed:

Pliers Flat-blade screwdriver

Phillips screwdriver Utility knife

5/16" (8 mm) and 1/4"

(6.35 mm) nut drivers or hex

sockets

Small level

Measuring tape or ruler 5/8" (16 mm) open-end

wrench

10" (254 mm) adjustable

wrench that opens to 11/8"

(29 mm)

Torx®†T20®and, if installing

custom front panels, Torx®

T15®✝screwdrivers

Other Useful Items You May Need:

Flashlight Shallow pan

Bath towel Masking or duct tape

Parts Supplied

Drain hose clamps (2)

(1 large/red and 1 small/green) Drain hose

#10 x 1/2" (12.7 mm)

Phillips-head screws (2) Undercounter mounting

brackets (2)

Make sure all these parts are included in the literature package.

Door handle (on some models)

✝®TORX, T20 and T15 are registred trademarks of Acument Intellectual Properties, LLC.

Optional Accessory Parts Available:

Moisture Barrier Tape

NOTE: Moisture barrier tape is

recommended if installing a

dishwasher under a wooden

countertop.

Side Panel Kit

For enclosing the side of the

dishwasher when installing it at

the end of your cabinetry

(Whirlpool part number varies

with color.)

Call us at our toll-free number or visit our website listed on the

Quick Start Guide for optional accessory part information.

First-Time Installations

Check local codes. Check existing electrical supply. See the

“Electrical Requirements” section. It is recommended that

electrical connections be made by a licensed electrical installer.

Additional Tools Needed:

Small tubing cutter Wire strippers

With 1/2" (12.7 mm), 3/4"

(19 mm), and 11/2" (38.1 mm)

hole saw bits

Additional Parts Needed (not provided):

3/8" (9.5 mm) Compression x

3/4" (19 mm) Hose Fitting with

rubber seal and 90° elbow

(required to properly connect

household water line to the

dishwasher)

Household Wiring (Metallic)

Strain Relief to fit 7/8" (22 mm)

hole (required to properly

secure household wiring to the

dishwasher terminal box)

NOTE: Use only: Straight:

Whirlpool Part Number

4317824, 90°: Whirlpool Part

Number W10278923RP

Twist-On Wire Connectors

NOTES:

nConfirm proper size for

connecting your gauge of

household wiring to the

16-gauge wiring in the

dishwasher.

nUse only: Straight:

Whirlpool Part Number

4317824, 90°: Whirlpool

Part Number

W10278923RP

Copper Tubing (3/8" [9.5 mm]

O.D. suggested) or Flexible

Braided Water Supply Line Kit.

Screw-Type Clamps 11/2"– 2"

(38 mm – 50 mm) (3 maximum)

Optional – Longer Drain

Hose Maximum length 12 ft

(3.7 m)

NOTE: Must meet

AHAM/IAPMO test standards,

fit 1" (25 mm) drain connection,

and be resistant to heat and

detergent.

NOTE: Be sure to purchase only Whirlpool factory-certified parts

and accessories for your appliance. Your installation may require

additional parts. To order, refer to the contact information

referenced in your Quick Start Guide.

NOTE: If using a flexible braided hose, replace inlet hose after

5 years to reduce the risk of hose failure. Record hose installation

or replacement dates on the hose for future reference.

For Direct Wire For Power Cord

Cabinet Grommet

For 11/2" (38 mm) hole in

cabinet

NOTE: Required for metal

cabinets

Power Cord Kit

Kit typically includes power

cord, metallic strain relief,

grommet, and twist-on wire

connectors (Straight: Whirlpool

Part Number 4317824, 90°:

Whirlpool Part Number

W10278923RP). For proper

installation, refer to the

installation instructions

provided with the kit.

NOTE: Be sure to purchase only Whirlpool factory-certified parts

and accessories for your appliance. Your installation may require

additional parts. To order, refer to the contact information

referenced in your Quick Start Guide.

Location Requirements

Dishwasher must be fully enclosed (top, sides, back, and floor)

upon installation. A side panel kit is available from your dealer for

installing your dishwasher at the end of your cabinetry.

An optional moisture barrier accessory is also available for

installing underneath a wooden countertop.

Check location where dishwasher will be installed. The location

must provide:

�Convenient access for loading and unloading dishes. Corner

locations require a 2" (51 mm) minimum clearance between

the side of the dishwasher door and the wall or cabinet.

�Easy access to water, electricity, and drain:

• Grounded electrical supply is required.

• This dishwasher has a water-heating feature and also

requires a connection to a hot water supply line.

• Make sure pipes, wires, and drain hose are within the

shaded area shown in the “Cabinet Opening Dimensions”

section.

• Do not run drain lines, water lines, or electrical wiring where

they can interfere with or contact dishwasher motor or legs.

• Shelter dishwasher and water lines leading to dishwasher

against freezing. Damage from freezing is not covered by

the warranty.

NOTE: If dishwasher will be left unused for a period of time

or in a location where it may be subject to freezing, have it

winterized by authorized service personnel.

• If installed in new construction, flush the water supply line of

debris before connecting it to the fill valve. If it is not

flushed, debris from the water supply could plug the fill

valve screen.

�A square opening for proper operation and appearance.

�The cabinet front to be perpendicular to floor.

�A level floor.

Helpful Hint: If floor at front of opening is not level with floor at

rear of opening, shims may be used to level dishwasher.

NOTE: To avoid shifting during dishwasher operation, shims must

be securely attached to the floor.

�The location where the dishwasher will be installed must

provide clearance between motor and flooring. Motor should

not touch the floor.

�Do not install dishwasher over carpeted flooring.

Cabinet Opening Dimensions

Clearances

Check that all surfaces have no protrusions that would prohibit

dishwasher installation.

A. Measured from the lowest point on the underside of the countertop.

May be reduced to 331/2" (851 mm) by removing the wheels and

perforated area of insulation (blanket) on dishwasher.

B. Minimum, measured from narrowest point of opening.

NOTE: Shaded areas of cabinet walls show where utility

connections may be installed.

Drain Requirements

�A new drain hose is supplied with your dishwasher. If drain

hose is not long enough, use a new drain hose with a

maximum length of 12 ft (3.7 m) that meets all current

AHAM/IAPMO test standards, is resistant to heat and

detergent, and fits the 1" (25 mm) drain connector of the

dishwasher.

NOTE: Do not connect multiple drain hoses together.

�Make sure to connect drain hose to waste tee or disposer inlet

above drain trap in house plumbing and 20" (508 mm)

minimum above the floor. It is recommended that the drain

hose either be looped up and securely fastened to the

underside of the counter or be connected to an air gap.

�Make sure to use an air gap if the drain hose is connected to

house plumbing lower than 20" (508 mm) above subfloor or

floor.

A. Air gap

34"

24"

(864 mm)

A(102 mm)

(76 mm)

(620 mm)

24"

(620 mm)

(51 mm)

(172 mm)

(267 mm)

(159 mm)

6¼"

(64 mm)

(44 mm)

10½"

6¾"

2¼"

1¾"

nIf required, the air gap should be installed in accordance with

the air gap installation instructions. When you are connecting

the air gap, a rubber hose (not provided) will be needed to

connect to the waste tee or disposer inlet.

nUse 1/2" (12.7 mm) minimum I.D. drain line fittings.

Water Supply Requirements

nThis dishwasher has a water heating feature and also requires

a connection to a hot water supply line.

nA hot water line with 20 psi to 120 psi (138 kPa to 827 kPa)

water pressure can be verified by a licensed plumber.

n120°F (49°C) water at dishwasher

n3/8" (9.5 mm) O.D. copper tubing with compression fitting or

flexible braided water supply line

NOTE: 1/2" (12.7 mm) minimum plastic tubing is not

recommended.

nA 90° elbow with 3/4" (19 mm) hose connection with rubber

washer

nDo not solder within 6" (152 mm) of the water inlet valve.

nIf installed in new construction, make sure the house water

supply lines have been flushed prior to connecting the

dishwasher to remove any debris that may exist in the supply

line.

NOTE: If replacing an existing dishwasher, it is recommended to

install a new water line and drain hose (supplied) with the new

dishwasher.

Electrical Requirements

Be sure that the electrical connection and wire size are adequate

and in conformance with the National Electrical Code, ANSI/NFPA

70 – latest edition, and all local codes and ordinances.

For a fee, a copy of the above code standards can be obtained

from: National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

You Must Have:

n120 V, 60 Hz, AC-only, 15 A or 20 A, fused electrical supply.

nCopper wire only.

nA maximum of 2 field wiring supply conductors (12 AWG

largest size) plus 1 grounding conductor are permitted in the

terminal box.

We Recommend:

nA time-delay fuse or circuit breaker.

Circuit Requirement:

nThe dishwasher may be installed on the same circuit as a

garbage disposal providing that the branch circuit cannot

exceed rated circuit load and must comply with all governing

codes and regulations such as but not limited to National

Electrical Code, ANSI/NFPA 70 - latest edition.

nNo electrical connections other than the dishwasher power

and ground connections can be made inside of the dishwasher

terminal box.

If Connecting Dishwasher with a Power Cord:

nUse a UL-listed power cord kit

marked for use with dishwasher. See

the “Tools and Parts” section for part

details.

nPlug into a grounded 3-prong outlet.

Outlet must meet all local codes and

ordinances.

If Connecting Dishwasher with Direct Wiring:

nUse flexible, armored, or nonmetallic

sheathed copper wire with grounding

wire that meets the wiring

requirements for your home and

local codes and ordinances.

nUse a UL-listed/CSA-approved metallic strain relief.

INSTALLATION INSTRUCTIONS

WARNING

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Doing so can result in serious injury or cuts.

You Need To:

nSlowly open dishwasher door while someone grasps the rear

of the dishwasher. Remove shipping materials and drain hose.

Close dishwasher door until latched.

NOTE: Each dishwasher is tested at the factory and may

contain some residual water in the tub as a result of the test.

nObserve all governing codes and ordinances.

nInstall this dishwasher as specified in these instructions.

nInstallation should be performed by a qualified

service technician.

nThe dishwasher must be installed to meet all electrical

and plumbing national and local codes and ordinances.

nCare shall be exercised when the appliance is installed

or removed to reduce the likelihood of damage to the

power cord.

WARNING: To reduce the risk of electric shock, fire, or injury to

persons, the installer must ensure that the dishwasher is

completely enclosed at the time of installation.

Before You Begin

WARNING

Electrical Shock Hazard

Disconnect electrical power at the fuse box or circuit

breaker box before installing appliance.

Failure to do so can result in death or electrical shock.

1. Disconnect power

Disconnect electrical power at the fuse box or circuit breaker

box before installing dishwasher.

2. Shut off water supply

Shut off water supply to the dishwasher.

Prepare Cabinet Opening – New

Utilities

3. Drill hole locations – new construction

1/2

A. Optional location

B. Preferred location

The power-supply receptacle for the appliance shall be

installed in a cabinet or on a wall adjacent to the

undercounter space in which the appliance is to be installed.

NOTE: Refer to the “Cabinet Opening Dimensions” section

for the correct hole placement and dimensions of the shaded

area.

Drill a 11/2" (38 mm) drain hole in the side or rear of cabinet,

depending on the location of the drain hose routing and drain

hose connection location.

Drill a 1/2" (12.7 mm) water supply hose hole in the side or

rear of cabinet, depending on location of water supply routing

and connection location.

Drill a 11/2" (38 mm) electrical conduit hole in the right-hand

side or rear of the cabinet.

4. Sand holes smooth

A. Wood cabinet

B. Metal cabinet

Wood cabinet: Sand the hole until smooth.

Metal cabinet: Cover edges of hole with grommet included

with power cord kit. See the “Tools and Parts” section for part

details.

Helpful Tip: Wiring the dishwasher will be easier if you route

the cable into the cabinet opening from the right-hand side.

Install Optional Moisture Barrier

(Recommended for Wood

Countertops)

Moisture barrier/Wood shims

A. Install wood shims

B. Moisture barrier

Make sure the area under the cabinet is clean and dry for

installation of the moisture barrier. Remove the backing of the

moisture barrier and apply to underside of the countertop along

the front edge of the counter.

NOTE: Install wood shims if side anchoring and the gap between

sides of the dishwasher are greater than 1/2" (12.7 mm) on each

side or are greater than the length of the anchor screws.

5. Built-up floors – add shims as needed

101 mm

2¾"

70 mm

50 mm

Built-up floors: If the kitchen floor is higher than the cabinet

opening’s floor—for example, the kitchen floor tile does not

extend into the cabinet opening—add shims, as needed, in

the area shown to bring the dishwasher up to 34" (864 mm)

below the countertop.

NOTE: Shims must be securely attached to floor to avoid

movement when the dishwasher is in use.

6. If installing into a 331/2" (851 mm) opening

Cut insulation blanket along perforation for cabinet opening

height of 331/2" (851 mm). For other cabinet opening heights,

do not cut the insulation blanket.

Electrical Connection

– For Direct Wire, begin with step 7

– For Power Cord, wait until step 22

– For Factory Installed Power Cord, begin with Step 29

7. Direct wire – route cable

6”

(152 mm)

If installing with direct wire, route the cable as shown.

Route cable from power supply through cabinet hole. (Cable

must extend to the right-front side of cabinet opening.) Tape

cable to the floor in area shown. This will prohibit cable from

moving when dishwasher is moved into cabinet opening.

NOTE: If removing a previous dishwasher with a power cord,

you will need to transfer the power cord to the new

dishwasher.

Prepare Dishwasher

WARNING

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Doing so can result in serious injury or cuts.

WARNING

Excessive Weight Hazard

Use two or more people to move and install or uninstall

appliance.

Failure to do so can result in back or other injury.

8. Put dishwasher on its back

Helpful Tip: Place cardboard under dishwasher until installed

in cabinet opening to avoid damaging floor covering.

Using 2 or more people, grasp sides of dishwasher door

frame and place the dishwasher on its back.

Do not use the door panel as a worktable without first

covering it with a towel to avoid scratching the door panel.

NOTE: On some models, once the dishwasher is on its back,

pull on the door handle to remove it from the access panel.

Remove Access Panel

– For Plastic Access Panels, go to step 9

– For Metal Access Panels, go to step 10

9. Plastic panel

A. Unlocked

B. locked

C. 1/4 turn

Using a flat-blade screwdriver, turn the plastic fasteners 1/4

turn counterclockwise to unlock them. Go to step 12.

10. Metal panel

Using a 1/4" (6.35 mm) nut driver or Phillips screwdriver,

remove 2 screws attaching access panel to dishwasher.

11. Measure cabinet opening

Measure height of cabinet opening from underside of

countertop to floor where dishwasher will be installed. Be

sure to measure the lowest point on the underside of the

countertop and the highest point on the floor.

Dishwasher Height Adjustment Chart

Cabinet-opening

height

Front legs height

ARear legs height

331/2" (851 mm) 3/8" (9.8 mm) Remove legs and

spacers.

34" (864 mm) 7/8" (22 mm) 1" (25.4 mm)

341/2" (876 mm) 11/8" (28.8 mm) 11/4" (31.3 mm)

Front legs – A

Rear legs – B

Adjust both front and back leveling legs to the same height.

NOTE: If the minimum cabinet opening height is less than

337/8" (860 mm), the rear leveling legs and spacers can be

removed for additional clearance. This will allow the

dishwasher to fit into a 331/2" (851 mm) high cabinet opening,

but the dishwasher will be more difficult to move.

(Measurements are approximate. Rear and front leveling

legs are preset at the factory for 341/2" [876 mm].)

12. Adjust leveling legs

Refer to the “Dishwasher Height Adjustment Chart” for height

of leveling legs needed for your cabinet opening.

13. Remove plastic rail cover

A. Plastic rail cover

Remove and discard the plastic rail cover on each side of the

dishwasher frame. To remove the plastic rail cover, push

upward and back to unsnap it from the dishwasher frame.

Connect Water Line to Fill Valve

– For Copper Line, begin with step 14

– For Flexible Line, begin with step 16

14. Copper water line

If using copper tubing, measure overall length of copper

tubing required to reach the water supply, cut to length, and

attach with compression fittings.

15. Slide nut and ferrule onto tubing (copper

tubing only)

A. Nut

B. Ferrule

Copper tubing only: Put the tubing into the 90° elbow fitting

as far as it will go. (The copper tubing bends and kinks

easily.) Slide the nut and ferrule forward and start the nut

onto the elbow threads.

NOTE: To avoid vibration during operation, route the water

supply line so that it does not touch the dishwasher base,

frame, or motor. Go to step 18.

16. Flexible line

Flexible braided line: Confirm the flexible braided line is

long enough.

17. Add 90° elbow fitting to the water supply line

Get 3/8" (9.5 mm) compression x 3/4" (19 mm) hose fitting

with 90° elbow. See the “Tools and Parts” section at the front

of the guide for part details and order. Connect the 3/8"

(9.5 mm) compression fitting of the 90° elbow fitting to the

water supply line. Attach so the 3/4" (19 mm) connection is

facing upward as shown above.

Connect Fill Hose to Fill Valve

18. Tighten 90° elbow fitting to valve

Be sure rubber washer is properly seated in fitting. Slide the

3/4" (19 mm) fitting of the 90° elbow up to the valve and

hand-tighten to avoid cross-threading. Hand-tighten until the

coupling is tight. Using pliers, check the tightness of the

coupling. An additional 1/4 to 1/2 turn may be required to

seal the rubber gasket. Route fill hose out the rear left side of

unit.

NOTES:

nDo not use PTFE plumber's tape with compression

fittings.

nDo not overtighten. Damage to the coupling can result.

Drain Hose Connection

19. Connect drain hose

A. Small clamp

B. Rubber drain

hose

connector

C. Stop

D. Drain hose stop

E. Drain hose

Place towel under drain hose to catch any water in drain

hose. Place the small (green) drain hose clamp onto the

small end of the drain hose. Push the new drain hose into the

rubber drain hose connector up to the drain hose stop.

20. Slide clamp onto connector

A. Small clamp

B. Rubber drain

hose

connector

C. Stop

D. Drain hose stop

E. Drain hose

Using pliers, squeeze open the small drain hose clamp, and

slide it onto the connector between stops.

21. Hose clamp final position

A. Drain hose

B. Drain hose

stop

C. Small clamp

D. Rubber drain hose

connector

E. Stop

NOTE: Route drain hose out the rear of the dishwasher.

Power Cord Connection

NOTE: If removing a previous dishwasher with a power cord, you

will need to transfer the power cord to the new dishwasher.

22. Remove terminal box cover

Using a 1/4" hex-head socket, nut driver, or Torx®T20®

screwdriver, remove terminal box cover. Retain for later use.

23. Install strain relief

Install the metallic strain relief provided in this kit (Straight:

Whirlpool Part Number 4317824, 90°: Whirlpool Part Number

W10278923RP). Make sure screw heads are facing to the

left when tightening conduit nut. Strain relief is provided with

the power cord kit.

24. Power cord – route cord into terminal box

Route cord so that it does not touch dishwasher motor or

lower part of dishwasher tub. Pull cord through strain relief in

terminal box.

NOTE: A maximum of 2 power cord supply conductors (12

AWG largest size) plus 1 grounding conductor are permitted

in the terminal box.

WARNING

Electrical Shock Hazard

Electrically ground appliance.

Connect ground wire to green ground connector in

terminal box.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

25. Power cord – connect ground wire

A. Ground wire

Remove the ground connector screw and place it through the

ring terminal of the green ground wire of power cord.

Reattach and tighten the ground connector screw.

26. Power cord – connect remaining wires

Select twist-on wire connectors of the proper size provided in

this kit (Straight: Whirlpool Part Number 4317824, 90°:

Whirlpool Part Number W10278923RP) . Connect wires,

black to black and white to white, using the twist-on wire

connectors.

NOTE: Do not pre-twist stranded wire. Twist on wire

connector. Gently tug on wires to be sure both are secured.

Wiring configuration

Power supply

wire: Terminal box

wire:

white white

black black

ground wire ground connector

27. Power cord – secure cord in strain relief

Tighten strain relief screws to secure cord.

28. Power cord – reinstall terminal box cover and

wires

Place wires inside terminal box. Insert tabs on left side of

cover. Make sure wires are tucked inside the box and not

pinched by the cover. Use a 1/4" hex-head socket, nut driver,

or Torx®T20®screwdriver, and the screw removed in step 22

to secure the terminal box cover.

If power cord supplied model, remove the first tie strap

closest to the plug to maximize the cord length. Do not

remove any other tie straps.

NOTE: Route power cord out the rear of the dishwasher. Do

not plug cord into an outlet until instructed to do so.

29. Factory Installed Power Cord (on some

models)

Select products include a factory installed power cord. For

these products, no wiring during install is required. A ground

wire to chassis connection is made inside the existing

terminal box, and the normal terminal box cover is not

included.

No connection or modification of wiring in that junction box is

required for these factory power cord models.

Install Door Handle (on some

models)

30. Install door handle

A. Setscrew (in

bottom of

handle)

B. Hex key

C. Handle

D. Mounting stud

IMPORTANT: Do not scratch the front panel during this

procedure. If door panel has a protective film, peel film back

past the point of the handle studs before installing handle.

Handle is easiest to install while unit is on its back.

Remove the door handle and hex key from the packaging.

Setscrews are already installed in the handle. Place handle

on mounting studs with the setscrews facing down. Push the

door handle tightly against the door. Insert the short end of

the hex key into the setscrews. Tighten the setscrews 1/4

turn past snug.

Retain hex key with Owner’s Manual.

Place Dishwasher in Cabinet

WARNING

Excessive Weight Hazard

Use two or more people to move and install or uninstall

appliance.

Failure to do so can result in back or other injury.

31. Stand dishwasher upright

Using 2 or more people, stand the dishwasher up.

NOTE: Do not install kick plate until instructed to do so.

IMPORTANT: If wheels were removed, cover the floor when

moving the dishwasher. Slowly move dishwasher completely

into cabinet opening. Do not kink or pinch water line, drain

hose, power cord, or direct wire between dishwasher and

cabinet. Remove cardboard from under dishwasher.

It is all right if dishwasher fits tightly into cabinet opening. Do

not remove insulation blanket—the blanket reduces the

sound level.

NOTE: Route water supply, drain hose, and power cord out

the rear of the dishwasher.

32. Move dishwasher close to cabinet opening

B C

A. Water line

B. Cable

C. Drain hose

Route the utilities through the holes in the cabinet and pull

the slack out at the same time as the dishwasher is pushed

into the cabinet.

33. Route power cord.

If using a power cord, make sure to route end through hole in

cutout before sliding dishwasher into cabinet opening.

34. Secure installation blanket

A. Insulation blanket

B. Secure blanket

NOTE: Make sure insulation blanket is secured at both left

and right rear corners before pushing into cabinet opening to

keep the blanket from bunching up in a tight-fitting cabinet.

35. Move dishwasher all but 6" (152 mm) into

cabinet opening

(152 mm)

NOTE: Leave unit about 6" (152 mm) out from cabinet in

order to install anchor brackets and adjust door tension if

needed.

36. Pull slack from utilities

NOTE: Pull slack out of utilities at the same time the

dishwasher is pushed into the cabinet opening to avoid any

kinks.

Choose Anchor Attachment Method

IMPORTANT: The dishwasher must be secured to the cabinet as

one of the final steps. Prepare the dishwasher for this by attaching

the 2 brackets found in the parts bag to the dishwasher.

– For countertops that are wood, laminate, or another similar

surface, use Countertop Attachment: go to step 37

– For countertops that are marble, granite, or another hard

surface, use Side Attachment: go to step 38

NOTE: If the gap between the top of the door and the underside of

the countertop is tight (less than 1/4" [6.35 mm]), we suggest

using Side Attachment to keep from scratching the User Interface

or console with the anchor screws.

Countertop Attachment:

37. Insert bracket

NOTE: Tabs must point to the right.

Remove the brackets from the package and insert into the

open slots on the left- and right-hand top of the dishwasher

collar as shown. Go to step 42.

Bend tab

Using pliers, bend/twist tab to lock the brackets in place.

Side Attachment:

38. Break end of bracket

A. Scored line for stainless steel tub models

B. Scored line for plastic tub models

Break off the end of the bracket along the scored line using

pliers.

39. Install bracket

A. Bend tabs

Push bracket into slot on the side of dishwasher and bend

tab in toward the side of the dishwasher so that it keeps the

bracket in place. Repeat this step for the other side of the

dishwasher.

NOTE: Install wood shims to the inside of the cabinets if the

gap between the sides of the cabinet and the sides of the

dishwasher are greater than 1/2" (13 mm) on each side.

NOTE: Do not attach the dishwasher. This will be done later.

Final Installation Check

40. Open and close door

41. Closes too quickly – decrease spring tension

If the door closes too quickly, decrease the spring tension by

moving the spring end toward the front of the dishwasher.

NOTE: Springs should be in the same notches on left and

right sides.

42. Closes too quickly – decrease spring tension

If the door falls open, increase the spring tension by moving

the spring end toward the back of the dishwasher.

NOTE: Springs should be in the same notches on left and

right sides.

43. Align front of dishwasher with front of cabinet

doors

Align front of dishwasher door panel with front of cabinet

doors. You may need to adjust alignment to be even with

your cabinets.

44. Check for plumb and adjust legs if needed

Check that leveling legs are firmly against the floor. Close

and latch the door and place level against the front panel.

Check that dishwasher is centered from front to back in the

opening. If needed, adjust leveling leg until dishwasher is

plumb. Repeat for other side of dishwasher.

Helpful Tip: Push up on front of dishwasher to raise

dishwasher off the ground to adjust front legs. With some

installations, it may be easier to adjust the front leg using a

3/16" hex head socket or adjustable wrench. If the gap

between the top of the door and the underside of the

countertop is tight (less than 1/4" [6 mm]), we suggest side

anchoring to keep from scratching the control panel or

console.

Level legs

A. Preferred method

B. Optional method

45. Check level side to side and adjust legs if

needed

Place level against top-front opening of tub. Check that

dishwasher is level from side to side. If dishwasher is not

level, adjust front legs up or down until dishwasher is level.

Secure Dishwasher in Cabinet

Opening

46. Double-check dishwasher alignment in

cabinet opening

Check that dishwasher is still level front to back and side to

side in the cabinet opening.

Open dishwasher door and place towel over pump assembly

and spray arm of dishwasher. For some models, you may

have to remove lower dish rack. This will keep screws from

falling into pump area when you are securing dishwasher to

countertop or cabinet.

47. Secure dishwasher

A. Screw to side cabinet

Open dishwasher door to prepare for securing the

dishwasher to the countertop or side cabinet.

NOTES:

nThe dishwasher must be secured to keep it from shifting

when the door is opened or closed.

nDo not drop screws into bottom of dishwasher.

nLocate brackets installed in the “Choose Anchor

Attachment Method” section, either on top or on the sides

of the dishwasher.

nIf countertop anchoring: Secure dishwasher to the

countertop with two #10 x 1/2" Phillips-head screws

(included).

nIf side anchoring: Drill pilot holes in cabinet to avoid

splitting the wood. Secure dishwasher to cabinet with two

#10 x 1/2" Phillips-head screws (included). Remove

upper rack for easier access.

48. Check door clearance

IMPORTANT: Check that top of door does not contact

screws, brackets, or countertop. If it does, adjust leveling

legs or use the side attachment option.

49. Check inner spacing

Open door and check that space between dishwasher

cabinet opening and tub is equal on both sides. If spacing is

not equal, loosen bracket screws and shift tub. Tighten

bracket screws.

Direct Wire Connection

50. Remove terminal box cover

Using a 1/4" hex-head socket, nut driver, or Torx®T20®

screwdriver, remove terminal box cover. Retain for later use.

51. Install strain relief

Install a UL-listed/CSA-approved metallic strain relief.

52. Route cable into terminal box

Route cable so that it does not touch dishwasher motor or

lower part of dishwasher tub. Pull cable through UL-listed/

CSA-approved strain relief in terminal box. Strain relief is not

supplied with the dishwasher. Owner must purchase a 7/8"

(22 mm) screw-in type strain relief.

Select UL-listed/CSA-approved twist-on wire connectors (not

included) rated to connect your household wiring to 16-gauge

dishwasher wiring.

WARNING

Electrical Shock Hazard

Electrically ground appliance.

Connect ground wire to green ground connector in

terminal box.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

53. Direct wire – connect ground wire

A. Ground wire

B. Ground screw

Form bare ground wire into a U-shaped hook. Wrap ground

wire hook clockwise around the ground connector screw and

under the washer. Securely tighten ground connector screw.

54. Direct wire – connect remaining wires

Select UL-listed/CSA-approved twist-on wire connectors of

the proper size. Connect wires, black to black and white to

white, using the twist-on wire connectors.

NOTE: Do not pre-twist stranded wire. Twist on wire

connector. Gently tug on wires to be sure both are secured.

Wiring configuration

Power supply

wire: Terminal box

wire:

white white

black black

ground wire ground connector

55. Direct wire – secure cable in strain relief

Tighten strain relief screws to secure cable.

56. Direct wire – reinstall terminal box cover and

wires

Place wires inside terminal box. Insert tabs on left side of

cover. Make sure wires are tucked inside box. Close cover

ensuring wires are not pinched. Use 1/4" nut driver or Torx®

T20®screwdriver and previously removed screw to secure

cover.

La page charge ...

Whirlpool WDT751SAPZ Manuel utilisateur

Marque: Whirlpool

Modèle: WDT751SAPZ

Catégorie: Lave-vaisselle

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Whirlpool WDT751SAPZ User manual

Documents connexes

Autres documents

Jenn-Air JDTSS247HS Guide d'installation