MAAX 103409-300-502 Utile side wall 32 in. Guide d'installation

Taper
Guide d'installation
INSTALLATION INSTRUCTIONS
GUIDE D’INSTALLATION
GUÍA DE INSTALACIÓN
Read all instructions carefully before proceeding.
SAVE THIS GUIDE FOR FUTURE REFERENCE.
Lire toutes les instructions attentivement avant de
commencer l’installation.
CONSERVER POUR UN USAGE ULTÉRIEUR.
Leer detenidamente todas las instrucciones antes de
comenzar la instalación
CONSERVAR ESTE MANUAL COMO REFERENCIA.
A two person installation is required.
Une installation par deux
personnes est requise.
Se recomienda realizar la
instalación entre dos personas
ALCOVE SHOWER INSTALLATION (3 WALLS)
INSTALLATION DOUCHE EN ALCÔVE (3 MURS)
INSTALACIÓN DE DUCHA EN NICHO (3 MUROS)
HARDWARE INCLUDED
IN BOXES
QUINCAILLERIE INCLUSE
DANS LES BOÎTES
ACCESORIOS INCLUIDOS
EN LAS CAJAS
OPEN ALL BOXES
BEFORE YOU START
OUVREZ TOUTES LES
BOÎTES AVANT DE
COMMENCER
ABRIR TODAS LAS CAJAS
ANTES DE EMPEZAR
Serial numbers Numéros de série Números de serie
IMPORTANT Record the serial numbers
IMPORTANT Noter les numéros de série
IMPORTANTE Registre el número de serie
Voir Vidéo d'installation - Balayer
QR code avec un dispositif mobile
View Installation Video - Scan
QR code with a mobile device
Table of contents: Page
Tools and supplies.......................................................................................................................................... 3
Parts and components.................................................................................................................................... 4
1. Building the structure.................................................................................................................................. 6
2. Installing the base....................................................................................................................................... 7
2. Installing the base (Olympia)...................................................................................................................... 8
2. Installing the base (B3)............................................................................................................................... 9
2. Installing the base (Distinct / Zone square)................................................................................................ 10
3. Installing Ulok system on the walls............................................................................................................. 13
4. Temporary installation of the back wall....................................................................................................... 14
5. Temporary installation of the side walls.......................................................................................................15
6. Final installation of back wall...................................................................................................................... 18
7. Final installation of side walls..................................................................................................................... 19
8. Marking and drilling the glass shelf holes................................................................................................... 20
9. Silicone........................................................................................................................................................21
10. Glass shelf installation...............................................................................................................................21
11. Wall nish / Maintenance tips.................................................................................................................... 23
12. Warranty.................................................................................................................................................... 60
Table de matières: Page
Outils et materiaux.......................................................................................................................................... 3
Pièces et composantes...................................................................................................................................4
1. Construction de la structure........................................................................................................................ 24
2. Installation de la base................................................................................................................................. 25
2. Installation de la base (Olympia)................................................................................................................ 26
2. Installation de la base (B3)......................................................................................................................... 27
2. Installation de la base (Distinct / Zone square)........................................................................................... 28
3. Installation du système Ulok sur les murs.................................................................................................. 31
4. Installation temporaire du mur arrière......................................................................................................... 32
5. Installation temporaire des murs de côté.................................................................................................... 33
6. Installation nale du mur arrière................................................................................................................. 36
7. Installation nale des murs de côté............................................................................................................ 37
8. Marquage et perçage des trous pour la tablette......................................................................................... 38
9. Silicone........................................................................................................................................................39
10. Installation de la tablette............................................................................................................................39
11. Finition du mur / Conseils d'entretien........................................................................................................ 41
12. Garantie.................................................................................................................................................... 60
For installation steps in ENGLISHENGLISH go to page 6
Pour les étapes d'installation en FRANÇAIS aller à la page 24
Tabla de contenido: Página
Herramientas y materiales.............................................................................................................................. 3
Piezas y componentes....................................................................................................................................4
1. Construcción de la estructura..................................................................................................................... 42
2. Instalación de la base................................................................................................................................. 43
2. Instalación de la base (Olympia)................................................................................................................ 44
2. Instalación de la base (B3)......................................................................................................................... 45
2. Instalación de la base (Distinct / Zone square)........................................................................................... 46
3. Instalación del sistema Ulok sobre los muros............................................................................................ 49
4. Instalación temporal del muro posterior..................................................................................................... 50
5. Instalación temporal de los muros laterales............................................................................................... 51
6. Instalación nal del muro posterior............................................................................................................. 54
7. Instalación nal de los muros laterales....................................................................................................... 55
8. Marcado y perforación de agujeros para la repisa..................................................................................... 56
9. Silicona........................................................................................................................................................57
10. Instalación de la repisa..............................................................................................................................57
11. Acabado del muro / Consejos de mantenimiento...................................................................................... 59
12. Garantía.................................................................................................................................................... 60
Para las etapas en ESPAÑOL ir a la pagina 42
3
Hole saw
Scie-cloche
Sierra de
perforación
Screwdriver
Tournevis
Destornillador
24" level min.
Niveau de 24po. min.
Nivel de 24" min.
Pencil
Crayon
Lápiz
Measuring tape
Ruban à mesurer
Cinta métrica
18" square min.
Équerre de 18po. min.
Escuadra de 18" min.
Utility knife
Couteau à lame
rétractable
Cuchillo multiuso
Safety equipment
Équipement de sécurité
Equipamiento de
seguridad
1/8" drill bits
Mèches de 1/8
Box of #8x1¾"flathead screws
Boîte de vis #8x1¾"
à tête plate
Caja de tornillos #8x1¾"
de cabeza plana
Wood shims
Cales en bois
Cuñas de madera
50
Electric drill
Perçeuse électrique
Taladro eléctrico
TOOLS
REQUIRED
OUTILS
REQUIS
HERRAMIENTAS
NECESARIAS
SUPPLIES
SOLD SEPARATELY
MATÉRIAUX
VENDUS SÉPARÉMENT
MATERIALES
VENDIDOS POR SEPARADO
Clear silicone sealant
Silicone claire
Sellador de silicona
transparente
Self levening cement
Ciment auto-nivelant
Cemento
autonivelante
Shower drain
Drain de douche
Desagüe de ducha
*
* Drain required for the Distinct shower base
* Drain requis pour la base de douche Distinct
* Desagüe requerido para la base de ducha Distinct
Cement
Ciment
Cemento
4
6
1
43
2
109
8
5
11
7
# Part Nom de la pièce Pieza Qty/Qté Code
5 Glass shelf Tablette en verre Repisa 1
10060011
6 Bracket Support Soporte de repisa 2
7 #10 x 2’’ screws Vis #10 x 2’’ Tornillos #10 x 1½’’ (repisa) 2
8 Plastic washer Rondelle en plastique Arandela en plástico para repisa 2
9 Support cap Capuchon Tapa de la jación de repisa 2
10 #10 x ½ screws Vis #10 x ½ Tornillos #10 x ½ (para repisa) 2
11 Allen key Clé Allen Llave allen 1
12 Template Gabarit Plantilla de perforación 1
# Part Nom de la pièce Pieza Qt Code
13 Base Base Base 1 *
13a
Drain cover (with
Distinct base only)
Couvercle du drain lineaire (inclus
avec la base Distinct seulement)
Cubierta del desagüe (incluido
con la base Distinct únicamente)
1 10037090
14 Back wall Mur arrière Muro posterior 1 *
15 Side wall Mur de côté Muro lateral 2 *
16
Drain (included with Zone square
and B3Square base only)
Drain (inclus avec la base Zone
square et B3Square seulement)
Desagüe (incluido con la base Zone
square y B3Square únicamente )
1 10028619
PARTS INCLUDED IN PARTS PACK | PIÈCES COMPRISES DANS L'EMBALLAGE DES PIÈCES
| PIEZAS INCLUIDAS EN PAQUETE DE PIEZAS
PARTS INCLUDED IN SHELF PACK | PIÈCES COMPRISES DANS LA BOÎTE DE LA TABLETTE
| PIEZAS INCLUIDAS EN LA CAJA DE LA REPISA
12
Inside the sidewall box
À l'intérieur de la boîte
du mur de côté
En el interior de la caja
del muro lateral
Inside the backwall box
À l'intérieur de la boîte
du mur arrière
En el interior de la caja
del muro posterior
www.maax.com
10060303 – ULOK Skin pack for Utile - 1 junction
3
1
2
4
1
2
BACK WALL
MUR ARRIÈRE
MURO POSTERIOR
INSIDE VIEW
VUE INTÉRIEURE
VISTA INTERIOR
SIDE WALL
MUR DE CÔTÉ
MURO LATERAL
3
4
INSIDE VIEW
VUE INTÉRIEURE
VISTA INTERIOR
by/par
MAAX
* Extra parts are included in this pack in case of loss or damage
* Des pièces supplémentaires sont incluses en cas de perte ou bris
* Piezas extras están incluidas en este empaque en caso de perdida o daño
www.maax.com
10060303 – ULOK Skin pack for Utile - 1 junction
3
1
2
4
1
2
BACK WALL
MUR ARRIÈRE
MURO POSTERIOR
INSIDE VIEW
VUE INTÉRIEURE
VISTA INTERIOR
SIDE WALL
MUR DE CÔTÉ
MURO LATERAL
3
4
INSIDE VIEW
VUE INTÉRIEURE
VISTA INTERIOR
by/par
MAAX
* Extra parts are included in this pack in case of loss or damage
* Des pièces supplémentaires sont incluses en cas de perte ou bris
* Piezas extras están incluidas en este empaque en caso de perdida o daño
# Part Nom de la pièce Pieza Qty/Qté Code
1 X fastener Fixation en forme de X Sujetador en forma de X 4
10060303
2
#8 x 1¼’’ Screw
(for X fastener)
Vis #8 x 1¼’’ (Pour
xation en X)
Tornillos #8 x 1¼’’
(Para sujetador en X)
4
3 Retraction pin Cheville d'ancrage Pasador de retracción 4
4
#8 x ⅜ Screw (for
retraction pin)
Vis #8 x ⅜ (pour
cheville d'ancrage)
Tornillos #8 x ⅜ (para
pasador de retracción)
4
PARTS PIÈCES PIEZAS
COMPONENTS COMPOSANTES COMPONENTES
5
13
14
4
15
3
15
15
INSIDE VIEW
VUE INTÉRIEURE
VISTA INTERIOR
5
9
10
8
7
6
1
2
14
OVERVIEW VUE D'ENSEMBLE
VISTA GENERAL
6
Build a structure based on the dimensions in the chart
below.
IF STRUCTURE IS ALREADY BUILT CHECK THAT
IT RESPECTS THE DIMENSIONS BELOW
COMPATIBLE BASES No. A B C D
Olympia square 4832 106011
Between
48"- 48 1/4"
33 1/2"
16" 24"
Olympia square 6032 106012
Between
60"- 60 1/4"
16" 8 1/2"
B3 Square 4832 420001-5XX
Between
48"- 48 1/4"
33 1/2" 16"
24"
B3 Round 4832 410001-5XX
B3 Square 4836 420003-5XX
37 1/2" 18"
B3 Round 4836 410003-5XX
B3 Square 6032 420005-5XX
Between
60"- 60 1/4"
33 1/2" 16"
11 3/4"
B3 Round 6032 410005-5XX
B3 Square 6036 420006-5XX
37 1/2" 18"
B3 Round 6036 410006-5XX
Distinct 4832 106350 48" - 48 1/4" 33 1/2" 4 1/2" 24"
Zone Square 4832 106351 48" - 48 1/4" 33 1/2" 16" 24"
Zone Square 6032 106352 - 106353 60" - 60 1/4" 33 1/2" 16" 11 3/4"
Verify the wall studs are square, plumb and the
ooring is perfectly level.
6"
6"
C
For a worry free installation follow
all instructions and check them off
as you go.
Cut out an approximate 6" x 6" opening around
the drain center outlined by measurements C and
D. See image to the right and the chart above. We
recommend that a plumber completes the drain pipe
connection.
A
B
C
D
6"
A
B
C
D
6"
A
B
C
D
6"
A
B
C
D
Top view of structure
1.1
Check me!
1.2
Check me!
1.3
Check me!
D
1
STEP Building the structure
Before starting make sure to have all
parts and components refer to page 4.
View of 48" shower
Leveling the oor is critical for a properly aligned
installation. Auto leveling cement can be used to level
oor. Be careful not to block the drain hole position.
Respect front and inside corner studs position, others may vary.
FINAL VISUAL INSPECTION
Note: Not doing so could void your warranty
After removing the protective lm and prior to
completing the installation, perform a visual
inspection. If defects are visible, INTERRUPT
THE INSTALLATION and communicate with our
customer service: 1-877-438-6229
7
2
STEP Installing the base
B3 / Olympia / Zone Square / Distinct
Apply a 1/8" width silicone bead around the edge of
the drain hole in the base (surface between the top
part of the drain and the base). Assemble as shown.
HAND TIGHTEN ONLY !
REMOVE EXCESS SILICONE!
Install the base (13) pushing it completely against the
back studs. Center the base left to right inside the
alcove leaving equal spacing on both sides. (only for
alcove installation)
Centering the base left to right is
critical for side wall installation.
Top view
13
Remove the clear plastic lm from around the drain hole
and threshold before applying silicone. Keep the lm on
the base oor as protection untilinstallation is complete.
Top view
Flush
2.1
Check me!
2.2
Check me!
Cardboard
Rubber
Studs
Threshold
Drain assembly (included with Zone square and B3Square, required for the Distinct base)
Drain position varies according to base model
8
If needed, use wood shims between the studs and the
fastening ange to maintain centered position of base.
FOR OLYMPIA BASES DO NOT USE SHIMS UNDER
THE BASE TO LEVEL!
DOING SO WILL VOID THE MAAX WARRANTY!
13
With a 1/8" bit, drill holes in the fastening ange then
secure the base to all the wall studs with #8 x 1¾ "
screws (not included). Only pre-drill the flange not
the studs.
HAND TIGHTEN ONLY !
THE BOTTOM OF ALL HOLES IN THE FLANGE
HAVE TO BE AT LEAST 8MM (3/8") ABOVE THE
BASE THRESHOLD! HOLES MUST BE FILLED WITH
SILICONE BEFORE SCREWING
CUT THE EXCESS PART OF SHIMS
13
2
STEP Installing the base (cont'd)
Olympia
2.4
Check me!
2.5
Check me!
Ø 1/8"
3/8" (8 mm)
Tiling ange
COMPATIBLE BASES No.
Olympia square 4832 106011
Olympia square 6032 106012
13
Leveling the base is critical
for wall alignment
Verify that the base is completely level on all sides.
Conrm that the drain pipe is centered.
We recommend that a plumber completes the drain
pipe connection.
2.3
Check me!
9
With a 1/8" bit, drill holes in the fastening ange then
secure the base to all the wall studs with #8 x 1¾ "
screws (not included). Only pre-drill the flange not
the studs.
HAND TIGHTEN ONLY !
THE BOTTOM OF ALL HOLES IN THE FLANGE
HAVE TO BE AT LEAST 8MM (3/8") ABOVE THE
BASE THRESHOLD! HOLES MUST BE FILLED WITH
SILICONE BEFORE SCREWING
CUT THE EXCESS PART OF SHIMS
13
2
STEP Installing the base (cont'd)
B3
2.5
Check me!
Ø 1/8"
3/8" (8 mm)
Tiling ange
COMPATIBLE BASES No.
B3 Square 4832 420001-5XX
B3 Round 4832 410001-5XX
B3 Square 4836 420003-5XX
B3 Round 4836 410003-5XX
B3 Square 6032 410005-5XX
B3 Round 6032 410005-5XX
B3 Square 6036 410006-5XX
B3 Round 6036 410006-5XX
If needed, use wood shims between the studs and the
fastening ange to maintain centered position of base.
FOR B3 BASES YOU MAY USE SHIMS UNDER
THE BASE TO LEVEL (UNDER THE BASE LEGS
IDEALLY)
13
2.4
Check me!
13
Leveling the base is critical
for wall alignment
Lift the base. Place cement or wood shims under all legs
to support the shower base oor. Lower the shower base
and validate leveling and stability of the base on the
oor. If needed, use additional wood shims or cement.
We recommend that a plumber completes the drain
pipe connection.
2.3
Check me!
Shims and cement
Cales et ciment
Cuñas y cemento
Shims and
cement under
to level B3
bases
10
Lift the base. Insert wood shims on the oor around the
outline of the base on the previously marked spots to
compensate leveling.
Lower the base and validate leveling and the stability of
the base on the oor. If needed, use additional shims.
2
STEP Installing the base (cont'd)
Distinct / Zone Square
2.4
Check me!
COMPATIBLE BASES No.
Distinct 4832 106350
Zone square 4832 106351
Zone square 6032 106352 - 106353
Leveling the base is critical
for wall alignment
Verify the base leveling. Mark the studs and the oor
where shims will be required to perfectly level the base.
If the base is completely leveled go to step 2.5
2.3
Check me!
13
11
If needed use wood shims between the studs and the
fastening ange to maintain centered position of base.
2
STEP Installing the base (cont'd)
Distinct / Zone Square
2.6
Check me!
Lift the base. Place cement or wood shims under all legs
to support the shower base oor. Lower the shower base
and validate leveling and stability of the base on the
oor. If needed, use additional wood shims or cement.
We recommend that a plumber completes the drain
pipe connection.
2.5
Check me!
13
Distinct Zone Square
Legs
Check the position
of the legs under
the base to position
the shims if they are
necessary
12
Insert the drain cover (13a) as shown.
2
STEP Installing the base (cont'd)
Distinct / Zone Square
2.8
Check me!
With a 1/8" drill bit, drill holes in the base ange then
secure the base to all the wall studs with #8 x 1¾"
at-head screws (not included). Pre-drill the flange
only and not the studs.
HAND TIGHTEN ONLY!
THE BOTTOM OF ALL HOLES IN THE FLANGE
MUST BE AT LEAST 8MM (3/8") ABOVE THE BASE
THRESHOLD! HOLES MUST BE FILLED WITH
SILICONE BEFORE SCREWING
CUT THE EXCESS PART OF SHIMS
2.7
Check me!
Distinct 48 drain cover installation
13a
Ø 1/8"
3/8" (8 mm)
Tiling ange
13
13
3
STEP Installing Ulok system
on the walls
Install three X fasteners (1) on each side of the back wall
(14) in the pre drilled holes using the screws provided (2).
Quick tip
14
Back wall
1
14
2
2
1
14
This side
down
4
3
Fasten 3 retraction pins per side wall in the pre drilled
holes with the screws provided (4) to the left-hand or right-
hand fastening ange of the side walls (15) depending on
which side the wall will be installed on.
The side walls are interchangeable.
For left wall install the pins on the
right side, for the right wall install the
pins on the left side.
Quick tip
Side walls
15
15
Fastening ange
3.1
Check me!
3.2
Check me!
This side down
The Ulok system parts are in the side
wall boxes. (1 pack per side wall box)
There is a positioning pin on X
fastener so they can only be
installed one way.
Positioning
pin
www.maax.com
10060303 – ULOK Skin pack for Utile - 1 junction
3
1
2
4
1
2
BACK WALL
MUR ARRIÈRE
MURO POSTERIOR
INSIDE VIEW
VUE INTÉRIEURE
VISTA INTERIOR
SIDE WALL
MUR DE CÔTÉ
MURO LATERAL
3
4
INSIDE VIEW
VUE INTÉRIEURE
VISTA INTERIOR
by/par
MAAX
* Extra parts are included in this pack in case of loss or damage
* Des pièces supplémentaires sont incluses en cas de perte ou bris
* Piezas extras están incluidas en este empaque en caso de perdida o daño
www.maax.com
10060303 – ULOK Skin pack for Utile - 1 junction
3
1
2
4
1
2
BACK WALL
MUR ARRIÈRE
MURO POSTERIOR
INSIDE VIEW
VUE INTÉRIEURE
VISTA INTERIOR
SIDE WALL
MUR DE CÔTÉ
MURO LATERAL
3
4
INSIDE VIEW
VUE INTÉRIEURE
VISTA INTERIOR
by/par
MAAX
* Extra parts are included in this pack in case of loss or damage
* Des pièces supplémentaires sont incluses en cas de perte ou bris
* Piezas extras están incluidas en este empaque en caso de perdida o daño
14
4
STEP Temporary installation of the back
wall
Pull back the protective lm on the walls (14-15) at least
3" away from all edges. Keep the remaining protective
lm on the walls.
Quick tip
Installing the walls temporarily will
ensure proper wall alignment before
permanent installation.
Make sure the wall is plumb and
centered on the base.
With a 1/8" bit, drill holes in the back wall fastening
flange (14) at the top aligned with each stud. Only pre-
drill the flange not the studs. Then, secure the back
wall (14) with one #8 x 1¾" screw (not included) in one
of the pre-drilled holes.
IMPORTANT: HAND TIGHTEN ONLY. TEMPORARY
INSTALLATION.
Quick tip
Push the bottom of the back wall
with your foot when fastening in
place.
Plumbing the back wall is
critical for alignment of the
side walls
14
Base threshold
Back wall
Position and level the back wall (14) by sitting it on the
threshold at the back of the base.
4.1
Check me!
4.2
Check me!
4.3
Check me!
min.3/16"
max.3/8"
Stud
X fastener
15
Quick tip
Install the side wall (15) on the opposite side of the
faucet installation. Lift the wall approximately 3" above
the threshold of the base, push it completely against
the back wall then lower the side wall into position.
With a 1/8" bit, drill holes in the side wall fastening flange
(15) at the top aligned with each stud. Only pre-drill
the flange not the studs. Then, secure the side wall
(15) with one #8 x 1¾" screw (not included) in one of the
pre-drilled holes.
IMPORTANT: HAND TIGHTEN ONLY. TEMPORARY
INSTALLATION.
3
1
Side wall
Back wall
It is critical that all 3 retraction pins
engage with the X fasteners. There
should be no gap between the walls.
5
STEP Temporary installation of the side walls
Quick tip
Place a level vertically
on the side wall. If the
wall is not straight,
make sure that the
retraction pins are
properly inserted in
the X fasteners.
5.1
Check me!
5.2
Check me!
15
Base
Side wall
The side wall should now line up
with the front of the base. If it does
not, remove the walls and shim
the back ange of base.
16
5
STEP Temporary installation of the
side walls (Cont'd)
Measure the distance between the front face of the back
wall (14) and the center of the faucet. Then measure the
distance from the top of the base threshold to the center
of the faucet. If faucets are on the back wall, measure from
the center of the alcove to the center of the back wall.
Drill a hole from front for the faucets at the previously
marked positions. Pre-drill the hole with the ⅛'' drill bit.
The hole saw size is determined by the faucet type; refer
to the faucet installation manual for hole saw size.
Quick tip
Hole saws can be rented at your
local hardware store or any tool
rental location.
Faucet
center
Using those two measurements mark the position of the
faucet hole on the remaining side wall. Measure from the
side and bottom of the side wall where the retraction pins
are installed.
Repeat this process for all required faucet holes.
5.4
Check me!
5.3
Check me!
5.5
Check me!
Base
threshold
Front cut
view
Back
wall
Top view
For safe hole saw usage always
pre-drill a hole and wear safety
glasses when drilling.
Measure twice, drill once !
Record measures below.
Drilling faucet on side wall
17
Install the side wall (15) with the drilled faucet hole(s).
Lift the wall approximately 3" above the threshold of
the base, push it completely against the back wall
then lower the side wall into position.
Quick tip
With a 1/8" bit, drill holes in the side wall fastening flange
(15) at the top aligned with each stud. Only pre-drill
the flange not the studs. Then, secure the side wall
(15) with one #8 x 1¼" screw (not included) in one of the
pre-drilled holes.
IMPORTANT: HAND TIGHTEN ONLY. DO NOT
OVER-TIGHTEN THE SCREW.
3
1
Side wall
Back wall
Base
Side wall
BEFORE CONTINUING,
VALIDATE THAT ALL
THE WALLS ARE LEVEL,
PLUMB AND SQUARE
5
STEP Temporary installation of
the side walls (Cont'd)
The side wall should now line up
with the front of the base.
Make sure the retraction pins are
properly inserted in the X
fasteners. There should be no gap
between the walls.
Quick tip
Place a level vertically
on the side wall. If the
wall is not straight, make
sure that the X-fasteners
are properly inserted
5.6
Check me!
5.7
Check me!
5.8
Check me!
Threshold
18
6
STEP Final installation of back wall
Lift and place back wall (14) directly over the silicone wi-
thout sliding. Verify that the back wall (14) is plumb, shim
if needed. Then, secure the back wall to the wall studs at
top with #8 x 1¾" screws (not included) in the previously
drilled holes.
IMPORTANT: HAND TIGHTEN ONLY. DO NOT
OVER-TIGHTEN THE SCREWS.
Quick tip
Hold the bottom of the back wall
with your foot when fastening in
place.
13
Apply a bead of silicone on both sides of base (13) thres-
hold at 3/8" from the base side fastening flanges.
Apply silicone on both side of the back wall (14) just
before the wall side radius. The silicone applied on the
base and vertically on the back wall must overlap.
5
⅜"
Base
Back
wall
14
min.3/16"
max.3/8"
Stud
X fastener
It is critical for the side wall
installation to have at least ⅛'' and
no more than ⅜" between the stud
and the X fastener.
6.1
Check me!
6.3
Check me!
6.4
Check me!
Remove all walls from the structure.
Clean the shower base and apply a bead of silicone on
the threshold at 3/8" from the back fastening flange. Run
the bead of silicone the entire length of the base and 1''
on each side also.
6.2
Check me!
⅜"
⅜"
1"
19
Install the side wall (15) that is opposed to the faucet.
Lift the wall approximately 3 inches above the thres-
hold of the base, push it completely against the back
wall then slide the side wall into position.
WIPE OFF EXCESS SILICONE
3
1
Side wall
Back wall
7
STEP Final installation of side walls
Install the side wall (15) with the faucet hole. Lift the
wall approximately 3 inches above the threshold of the
base, push it completely against the back wall then
slide the side wall into position.
WIPE OFF EXCESS SILICONE
3
1
Side wall
Back wall
7.1
Check me!
7.2
Check me!
7.3
Check me!
BEFORE CONTINUING,
VALIDATE THAT ALL
THE WALLS ARE LEVEL,
PLUMB AND SQUARE
20
7
STEP Final installation of side walls (cont'd)
Secure the walls to the wall studs with #8 x 1¾ "
screws (not included) in the previously drilled holes.
Also, secure the walls by the fastening anges on the
sides of the walls. Use the pre-dilled holes.
If needed, use shims to keep walls plumb, square
and leveled. (Cut shim excess)
IMPORTANT: HAND TIGHTEN ONLY. DO NOT
OVER-TIGHTEN THE SCREWS.
Check me!
Check me!
Place the template in the corner of the shower where
you want to install your shelf.
Slide the template up until the points on the left and
right-hand side of the template are at the height you
want your shelf.
Use a pencil, marker or wax pencil to mark the spots
where the holes for the shelf will be drilled.
Drill the holes using a 9/64" drill bit.
8
STEP Marking and drilling the
glass shelf holes
Fold here
Drilling positions
Base
Side wall
THE SIDE WALLS SHOULD LINE UP WITH
THE BASE
?
?
?
?
Quick tip
90°
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60

MAAX 103409-300-502 Utile side wall 32 in. Guide d'installation

Taper
Guide d'installation