MAAX 103411-300-502 Utile back wall 48 in. Guide d'installation

INSTALLATION INSTRUCTIONS

GUIDE D’INSTALLATION

GUÍA DE INSTALACIÓN

Read all instructions carefully before proceeding.

SAVE THIS GUIDE FOR FUTURE REFERENCE.

Lire toutes les instructions attentivement avant de

commencer l’installation.

CONSERVER POUR UN USAGE ULTÉRIEUR.

Leer detenidamente todas las instrucciones antes de

comenzar la instalación

CONSERVAR ESTE MANUAL COMO REFERENCIA.

A two person installation is required.

Une installation par deux

personnes est requise.

Se recomienda realizar la

instalación entre dos personas

ALCOVE SHOWER INSTALLATION (3 WALLS)

INSTALLATION DOUCHE EN ALCÔVE (3 MURS)

INSTALACIÓN DE DUCHA EN NICHO (3 MUROS)

HARDWARE INCLUDED

IN BOXES

QUINCAILLERIE INCLUSE

DANS LES BOÎTES

ACCESORIOS INCLUIDOS

EN LAS CAJAS

OPEN ALL BOXES

BEFORE YOU START

OUVREZ TOUTES LES

BOÎTES AVANT DE

COMMENCER

ABRIR TODAS LAS CAJAS

ANTES DE EMPEZAR

Serial numbers • Numéros de série • Números de serie

IMPORTANT • Record the serial numbers

IMPORTANT • Noter les numéros de série

IMPORTANTE • Registre el número de serie

Voir Vidéo d'installation - Balayer

QR code avec un dispositif mobile

View Installation Video - Scan

QR code with a mobile device

Table of contents: Page

Tools and supplies.......................................................................................................................................... 3

Parts and components.................................................................................................................................... 4

1. Building the structure.................................................................................................................................. 6

2. Installing the base....................................................................................................................................... 7

2. Installing the base (Olympia)...................................................................................................................... 8

2. Installing the base (B3)............................................................................................................................... 9

2. Installing the base (Distinct / Zone square)................................................................................................ 10

3. Installing Ulok system on the walls............................................................................................................. 13

4. Temporary installation of the back wall....................................................................................................... 14

5. Temporary installation of the side walls.......................................................................................................15

6. Final installation of back wall...................................................................................................................... 18

7. Final installation of side walls..................................................................................................................... 19

8. Marking and drilling the glass shelf holes................................................................................................... 20

9. Silicone........................................................................................................................................................21

10. Glass shelf installation...............................................................................................................................21

11. Wall nish / Maintenance tips.................................................................................................................... 23

12. Warranty.................................................................................................................................................... 60

Table de matières: Page

Outils et materiaux.......................................................................................................................................... 3

Pièces et composantes...................................................................................................................................4

1. Construction de la structure........................................................................................................................ 24

2. Installation de la base................................................................................................................................. 25

2. Installation de la base (Olympia)................................................................................................................ 26

2. Installation de la base (B3)......................................................................................................................... 27

2. Installation de la base (Distinct / Zone square)........................................................................................... 28

3. Installation du système Ulok sur les murs.................................................................................................. 31

4. Installation temporaire du mur arrière......................................................................................................... 32

5. Installation temporaire des murs de côté.................................................................................................... 33

6. Installation nale du mur arrière................................................................................................................. 36

7. Installation nale des murs de côté............................................................................................................ 37

8. Marquage et perçage des trous pour la tablette......................................................................................... 38

9. Silicone........................................................................................................................................................39

10. Installation de la tablette............................................................................................................................39

11. Finition du mur / Conseils d'entretien........................................................................................................ 41

12. Garantie.................................................................................................................................................... 60

For installation steps in ENGLISHENGLISH go to page 6

Pour les étapes d'installation en FRANÇAIS aller à la page 24

Tabla de contenido: Página

Herramientas y materiales.............................................................................................................................. 3

Piezas y componentes....................................................................................................................................4

1. Construcción de la estructura..................................................................................................................... 42

2. Instalación de la base................................................................................................................................. 43

2. Instalación de la base (Olympia)................................................................................................................ 44

2. Instalación de la base (B3)......................................................................................................................... 45

2. Instalación de la base (Distinct / Zone square)........................................................................................... 46

3. Instalación del sistema Ulok sobre los muros............................................................................................ 49

4. Instalación temporal del muro posterior..................................................................................................... 50

5. Instalación temporal de los muros laterales............................................................................................... 51

6. Instalación nal del muro posterior............................................................................................................. 54

7. Instalación nal de los muros laterales....................................................................................................... 55

8. Marcado y perforación de agujeros para la repisa..................................................................................... 56

9. Silicona........................................................................................................................................................57

10. Instalación de la repisa..............................................................................................................................57

11. Acabado del muro / Consejos de mantenimiento...................................................................................... 59

12. Garantía.................................................................................................................................................... 60

Para las etapas en ESPAÑOL ir a la pagina 42

3

Hole saw

Scie-cloche

Sierra de

perforación

Screwdriver

Tournevis

Destornillador

24" level min.

Niveau de 24po. min.

Nivel de 24" min.

Pencil

Crayon

Lápiz

Measuring tape

Ruban à mesurer

Cinta métrica

18" square min.

Équerre de 18po. min.

Escuadra de 18" min.

Utility knife

Couteau à lame

rétractable

Cuchillo multiuso

Safety equipment

Équipement de sécurité

Equipamiento de

seguridad

1/8" drill bits

Mèches de 1/8

Box of #8x1¾"flathead screws

Boîte de vis #8x1¾"

à tête plate

Caja de tornillos #8x1¾"

de cabeza plana

Wood shims

Cales en bois

Cuñas de madera

50

Electric drill

Perçeuse électrique

Taladro eléctrico

TOOLS

REQUIRED

OUTILS

REQUIS

HERRAMIENTAS

NECESARIAS

SUPPLIES

SOLD SEPARATELY

MATÉRIAUX

VENDUS SÉPARÉMENT

MATERIALES

VENDIDOS POR SEPARADO

Clear silicone sealant

Silicone claire

Sellador de silicona

transparente

Self levening cement

Ciment auto-nivelant

Cemento

autonivelante

Shower drain

Drain de douche

Desagüe de ducha

*

* Drain required for the Distinct shower base

* Drain requis pour la base de douche Distinct

* Desagüe requerido para la base de ducha Distinct

Cement

Ciment

Cemento

4

6

1

43

2

109

8

5

11

7

# Part Nom de la pièce Pieza Qty/Qté Code

5 Glass shelf Tablette en verre Repisa 1

10060011

6 Bracket Support Soporte de repisa 2

7 #10 x 2’’ screws Vis #10 x 2’’ Tornillos #10 x 1½’’ (repisa) 2

8 Plastic washer Rondelle en plastique Arandela en plástico para repisa 2

9 Support cap Capuchon Tapa de la jación de repisa 2

10 #10 x ½ screws Vis #10 x ½ Tornillos #10 x ½ (para repisa) 2

11 Allen key Clé Allen Llave allen 1

12 Template Gabarit Plantilla de perforación 1

# Part Nom de la pièce Pieza Qt Code

13 Base Base Base 1 *

13a

Drain cover (with

Distinct base only)

Couvercle du drain lineaire (inclus

avec la base Distinct seulement)

Cubierta del desagüe (incluido

con la base Distinct únicamente)

1 10037090

14 Back wall Mur arrière Muro posterior 1 *

15 Side wall Mur de côté Muro lateral 2 *

16

Drain (included with Zone square

and B3Square base only)

Drain (inclus avec la base Zone

square et B3Square seulement)

Desagüe (incluido con la base Zone

square y B3Square únicamente )

1 10028619

PARTS INCLUDED IN PARTS PACK | PIÈCES COMPRISES DANS L'EMBALLAGE DES PIÈCES

| PIEZAS INCLUIDAS EN PAQUETE DE PIEZAS

PARTS INCLUDED IN SHELF PACK | PIÈCES COMPRISES DANS LA BOÎTE DE LA TABLETTE

| PIEZAS INCLUIDAS EN LA CAJA DE LA REPISA

12

Inside the sidewall box

À l'intérieur de la boîte

du mur de côté

En el interior de la caja

del muro lateral

Inside the backwall box

À l'intérieur de la boîte

du mur arrière

En el interior de la caja

del muro posterior

www.maax.com

10060303 – ULOK Skin pack for Utile - 1 junction

3

1

2

4

1

2

BACK WALL

MUR ARRIÈRE

MURO POSTERIOR

INSIDE VIEW

VUE INTÉRIEURE

VISTA INTERIOR

SIDE WALL

MUR DE CÔTÉ

MURO LATERAL

3

4

INSIDE VIEW

VUE INTÉRIEURE

VISTA INTERIOR

by/par

MAAX

* Extra parts are included in this pack in case of loss or damage

* Des pièces supplémentaires sont incluses en cas de perte ou bris

* Piezas extras están incluidas en este empaque en caso de perdida o daño

www.maax.com

10060303 – ULOK Skin pack for Utile - 1 junction

3

1

2

4

1

2

BACK WALL

MUR ARRIÈRE

MURO POSTERIOR

INSIDE VIEW

VUE INTÉRIEURE

VISTA INTERIOR

SIDE WALL

MUR DE CÔTÉ

MURO LATERAL

3

4

INSIDE VIEW

VUE INTÉRIEURE

VISTA INTERIOR

by/par

MAAX

* Extra parts are included in this pack in case of loss or damage

* Des pièces supplémentaires sont incluses en cas de perte ou bris

* Piezas extras están incluidas en este empaque en caso de perdida o daño

# Part Nom de la pièce Pieza Qty/Qté Code

1 X fastener Fixation en forme de X Sujetador en forma de X 4

10060303

2

#8 x 1¼’’ Screw

(for X fastener)

Vis #8 x 1¼’’ (Pour

xation en X)

Tornillos #8 x 1¼’’

(Para sujetador en X)

4

3 Retraction pin Cheville d'ancrage Pasador de retracción 4

4

#8 x ⅜ Screw (for

retraction pin)

Vis #8 x ⅜ (pour

cheville d'ancrage)

Tornillos #8 x ⅜ (para

pasador de retracción)

4

PARTS PIÈCES PIEZAS

COMPONENTS COMPOSANTES COMPONENTES

5

13

14

4

15

3

15

INSIDE VIEW

VUE INTÉRIEURE

VISTA INTERIOR

5

9

10

8

7

6

1

2

14

OVERVIEW VUE D'ENSEMBLE

VISTA GENERAL

6

Build a structure based on the dimensions in the chart

below.

IF STRUCTURE IS ALREADY BUILT CHECK THAT

IT RESPECTS THE DIMENSIONS BELOW

COMPATIBLE BASES No. A B C D

Olympia square 4832 106011

Between

48"- 48 1/4"

33 1/2"

16" 24"

Olympia square 6032 106012

Between

60"- 60 1/4"

16" 8 1/2"

B3 Square 4832 420001-5XX

Between

48"- 48 1/4"

33 1/2" 16"

24"

B3 Round 4832 410001-5XX

B3 Square 4836 420003-5XX

37 1/2" 18"

B3 Round 4836 410003-5XX

B3 Square 6032 420005-5XX

Between

60"- 60 1/4"

33 1/2" 16"

11 3/4"

B3 Round 6032 410005-5XX

B3 Square 6036 420006-5XX

37 1/2" 18"

B3 Round 6036 410006-5XX

Distinct 4832 106350 48" - 48 1/4" 33 1/2" 4 1/2" 24"

Zone Square 4832 106351 48" - 48 1/4" 33 1/2" 16" 24"

Zone Square 6032 106352 - 106353 60" - 60 1/4" 33 1/2" 16" 11 3/4"

Verify the wall studs are square, plumb and the

ooring is perfectly level.

6"

C

For a worry free installation follow

all instructions and check them off

as you go.

Cut out an approximate 6" x 6" opening around

the drain center outlined by measurements C and

D. See image to the right and the chart above. We

recommend that a plumber completes the drain pipe

connection.

A

B

C

D

6"

A

B

C

D

6"

A

B

C

D

6"

A

B

C

D

Top view of structure

1.1

Check me!

1.2

Check me!

1.3

Check me!

D

1

STEP Building the structure

Before starting make sure to have all

parts and components refer to page 4.

View of 48" shower

Leveling the oor is critical for a properly aligned

installation. Auto leveling cement can be used to level

oor. Be careful not to block the drain hole position.

Respect front and inside corner studs position, others may vary.

FINAL VISUAL INSPECTION

Note: Not doing so could void your warranty

After removing the protective lm and prior to

completing the installation, perform a visual

inspection. If defects are visible, INTERRUPT

THE INSTALLATION and communicate with our

customer service: 1-877-438-6229

7

2

STEP Installing the base

B3 / Olympia / Zone Square / Distinct

Apply a 1/8" width silicone bead around the edge of

the drain hole in the base (surface between the top

part of the drain and the base). Assemble as shown.

HAND TIGHTEN ONLY !

REMOVE EXCESS SILICONE!

Install the base (13) pushing it completely against the

back studs. Center the base left to right inside the

alcove leaving equal spacing on both sides. (only for

alcove installation)

Centering the base left to right is

critical for side wall installation.

Top view

13

Remove the clear plastic lm from around the drain hole

and threshold before applying silicone. Keep the lm on

the base oor as protection untilinstallation is complete.

Top view

Flush

2.1

Check me!

2.2

Check me!

Cardboard

Rubber

Studs

Threshold

Drain assembly (included with Zone square and B3Square, required for the Distinct base)

Drain position varies according to base model

8

If needed, use wood shims between the studs and the

fastening ange to maintain centered position of base.

FOR OLYMPIA BASES DO NOT USE SHIMS UNDER

THE BASE TO LEVEL!

DOING SO WILL VOID THE MAAX WARRANTY!

13

With a 1/8" bit, drill holes in the fastening ange then

secure the base to all the wall studs with #8 x 1¾ "

screws (not included). Only pre-drill the flange not

the studs.

HAND TIGHTEN ONLY !

THE BOTTOM OF ALL HOLES IN THE FLANGE

HAVE TO BE AT LEAST 8MM (3/8") ABOVE THE

BASE THRESHOLD! HOLES MUST BE FILLED WITH

SILICONE BEFORE SCREWING

CUT THE EXCESS PART OF SHIMS

13

2

STEP Installing the base (cont'd)

Olympia

2.4

Check me!

2.5

Check me!

Ø 1/8"

3/8" (8 mm)

Tiling ange

COMPATIBLE BASES No.

Olympia square 4832 106011

Olympia square 6032 106012

13

Leveling the base is critical

for wall alignment

Verify that the base is completely level on all sides.

Conrm that the drain pipe is centered.

We recommend that a plumber completes the drain

pipe connection.

2.3

Check me!

9

With a 1/8" bit, drill holes in the fastening ange then

secure the base to all the wall studs with #8 x 1¾ "

screws (not included). Only pre-drill the flange not

the studs.

HAND TIGHTEN ONLY !

THE BOTTOM OF ALL HOLES IN THE FLANGE

HAVE TO BE AT LEAST 8MM (3/8") ABOVE THE

BASE THRESHOLD! HOLES MUST BE FILLED WITH

SILICONE BEFORE SCREWING

CUT THE EXCESS PART OF SHIMS

13

2

STEP Installing the base (cont'd)

B3

2.5

Check me!

Ø 1/8"

3/8" (8 mm)

Tiling ange

COMPATIBLE BASES No.

B3 Square 4832 420001-5XX

B3 Round 4832 410001-5XX

B3 Square 4836 420003-5XX

B3 Round 4836 410003-5XX

B3 Square 6032 410005-5XX

B3 Round 6032 410005-5XX

B3 Square 6036 410006-5XX

B3 Round 6036 410006-5XX

If needed, use wood shims between the studs and the

fastening ange to maintain centered position of base.

FOR B3 BASES YOU MAY USE SHIMS UNDER

THE BASE TO LEVEL (UNDER THE BASE LEGS

IDEALLY)

13

2.4

Check me!

13

Leveling the base is critical

for wall alignment

Lift the base. Place cement or wood shims under all legs

to support the shower base oor. Lower the shower base

and validate leveling and stability of the base on the

oor. If needed, use additional wood shims or cement.

We recommend that a plumber completes the drain

pipe connection.

2.3

Check me!

Shims and cement

Cales et ciment

Cuñas y cemento

Shims and

cement under

to level B3

bases

10

Lift the base. Insert wood shims on the oor around the

outline of the base on the previously marked spots to

compensate leveling.

Lower the base and validate leveling and the stability of

the base on the oor. If needed, use additional shims.

2

STEP Installing the base (cont'd)

Distinct / Zone Square

2.4

Check me!

COMPATIBLE BASES No.

Distinct 4832 106350

Zone square 4832 106351

Zone square 6032 106352 - 106353

Leveling the base is critical

for wall alignment

Verify the base leveling. Mark the studs and the oor

where shims will be required to perfectly level the base.

If the base is completely leveled go to step 2.5

2.3

Check me!

13

11

If needed use wood shims between the studs and the

fastening ange to maintain centered position of base.

2

STEP Installing the base (cont'd)

Distinct / Zone Square

2.6

Check me!

Lift the base. Place cement or wood shims under all legs

to support the shower base oor. Lower the shower base

and validate leveling and stability of the base on the

oor. If needed, use additional wood shims or cement.

We recommend that a plumber completes the drain

pipe connection.

2.5

Check me!

13

Distinct Zone Square

Legs

Check the position

of the legs under

the base to position

the shims if they are

necessary

12

Insert the drain cover (13a) as shown.

2

STEP Installing the base (cont'd)

Distinct / Zone Square

2.8

Check me!

With a 1/8" drill bit, drill holes in the base ange then

secure the base to all the wall studs with #8 x 1¾"

at-head screws (not included). Pre-drill the flange

only and not the studs.

HAND TIGHTEN ONLY!

THE BOTTOM OF ALL HOLES IN THE FLANGE

MUST BE AT LEAST 8MM (3/8") ABOVE THE BASE

THRESHOLD! HOLES MUST BE FILLED WITH

SILICONE BEFORE SCREWING

CUT THE EXCESS PART OF SHIMS

2.7

Check me!

Distinct 48 drain cover installation

13a

Ø 1/8"

3/8" (8 mm)

Tiling ange

13

3

STEP Installing Ulok system

on the walls

Install three X fasteners (1) on each side of the back wall

(14) in the pre drilled holes using the screws provided (2).

Quick tip 

14

Back wall

1

14

2

1

14

This side

down

4

3

Fasten 3 retraction pins per side wall in the pre drilled

holes with the screws provided (4) to the left-hand or right-

hand fastening ange of the side walls (15) depending on

which side the wall will be installed on.

The side walls are interchangeable.

For left wall install the pins on the

right side, for the right wall install the

pins on the left side.

Quick tip 

Side walls

15

Fastening ange

3.1

Check me!

3.2

Check me!

This side down

The Ulok system parts are in the side

wall boxes. (1 pack per side wall box)

There is a positioning pin on X

fastener so they can only be

installed one way.

Positioning

www.maax.com

10060303 – ULOK Skin pack for Utile - 1 junction

3

1

2

4

1

2

BACK WALL

MUR ARRIÈRE

MURO POSTERIOR

INSIDE VIEW

VUE INTÉRIEURE

VISTA INTERIOR

SIDE WALL

MUR DE CÔTÉ

MURO LATERAL

3

4

INSIDE VIEW

VUE INTÉRIEURE

VISTA INTERIOR

by/par

MAAX

* Extra parts are included in this pack in case of loss or damage

* Des pièces supplémentaires sont incluses en cas de perte ou bris

* Piezas extras están incluidas en este empaque en caso de perdida o daño

www.maax.com

10060303 – ULOK Skin pack for Utile - 1 junction

3

1

2

4

1

2

BACK WALL

MUR ARRIÈRE

MURO POSTERIOR

INSIDE VIEW

VUE INTÉRIEURE

VISTA INTERIOR

SIDE WALL

MUR DE CÔTÉ

MURO LATERAL

3

4

INSIDE VIEW

VUE INTÉRIEURE

VISTA INTERIOR

by/par

MAAX

* Extra parts are included in this pack in case of loss or damage

* Des pièces supplémentaires sont incluses en cas de perte ou bris

* Piezas extras están incluidas en este empaque en caso de perdida o daño

14

4

STEP Temporary installation of the back

wall

Pull back the protective lm on the walls (14-15) at least

3" away from all edges. Keep the remaining protective

lm on the walls.

Quick tip 

Installing the walls temporarily will

ensure proper wall alignment before

permanent installation.

Make sure the wall is plumb and

centered on the base.

With a 1/8" bit, drill holes in the back wall fastening

flange (14) at the top aligned with each stud. Only pre-

drill the flange not the studs. Then, secure the back

wall (14) with one #8 x 1¾" screw (not included) in one

of the pre-drilled holes.

IMPORTANT: HAND TIGHTEN ONLY. TEMPORARY

INSTALLATION.

Quick tip 

Push the bottom of the back wall

with your foot when fastening in

place.

Plumbing the back wall is

critical for alignment of the

side walls

14

Base threshold

Back wall

Position and level the back wall (14) by sitting it on the

threshold at the back of the base.

4.1

Check me!

4.2

Check me!

4.3

Check me!

min.3/16"

max.3/8"

Stud

X fastener

15

Quick tip 

Install the side wall (15) on the opposite side of the

faucet installation. Lift the wall approximately 3" above

the threshold of the base, push it completely against

the back wall then lower the side wall into position.

With a 1/8" bit, drill holes in the side wall fastening flange

(15) at the top aligned with each stud. Only pre-drill

the flange not the studs. Then, secure the side wall

(15) with one #8 x 1¾" screw (not included) in one of the

pre-drilled holes.

IMPORTANT: HAND TIGHTEN ONLY. TEMPORARY

INSTALLATION.

3

1

Side wall

Back wall

It is critical that all 3 retraction pins

engage with the X fasteners. There

should be no gap between the walls.

5

STEP Temporary installation of the side walls

Quick tip 

Place a level vertically

on the side wall. If the

wall is not straight,

make sure that the

retraction pins are

properly inserted in

the X fasteners.

5.1

Check me!

5.2

Check me!

15

Base

Side wall

The side wall should now line up

with the front of the base. If it does

not, remove the walls and shim

the back ange of base.

16

5

STEP Temporary installation of the

side walls (Cont'd)

Measure the distance between the front face of the back

wall (14) and the center of the faucet. Then measure the

distance from the top of the base threshold to the center

of the faucet. If faucets are on the back wall, measure from

the center of the alcove to the center of the back wall.

Drill a hole from front for the faucets at the previously

marked positions. Pre-drill the hole with the ⅛'' drill bit.

The hole saw size is determined by the faucet type; refer

to the faucet installation manual for hole saw size.

Quick tip 

Hole saws can be rented at your

local hardware store or any tool

rental location.

Faucet

center

Using those two measurements mark the position of the

faucet hole on the remaining side wall. Measure from the

side and bottom of the side wall where the retraction pins

are installed.

Repeat this process for all required faucet holes.

5.4

Check me!

5.3

Check me!

5.5

Check me!

Base

threshold

Front cut

view

Back

wall

Top view

For safe hole saw usage always

pre-drill a hole and wear safety

glasses when drilling.

Measure twice, drill once !

Record measures below.

Drilling faucet on side wall

17

Install the side wall (15) with the drilled faucet hole(s).

Lift the wall approximately 3" above the threshold of

the base, push it completely against the back wall

then lower the side wall into position.

Quick tip 

With a 1/8" bit, drill holes in the side wall fastening flange

(15) at the top aligned with each stud. Only pre-drill

the flange not the studs. Then, secure the side wall

(15) with one #8 x 1¼" screw (not included) in one of the

pre-drilled holes.

IMPORTANT: HAND TIGHTEN ONLY. DO NOT

OVER-TIGHTEN THE SCREW.

3

1

Side wall

Back wall

Base

Side wall

BEFORE CONTINUING,

VALIDATE THAT ALL

THE WALLS ARE LEVEL,

PLUMB AND SQUARE

5

STEP Temporary installation of

the side walls (Cont'd)

The side wall should now line up

with the front of the base.

Make sure the retraction pins are

properly inserted in the X

fasteners. There should be no gap

between the walls.

Quick tip 

Place a level vertically

on the side wall. If the

wall is not straight, make

sure that the X-fasteners

are properly inserted

5.6

Check me!

5.7

Check me!

5.8

Check me!

Threshold

18

6

STEP Final installation of back wall

Lift and place back wall (14) directly over the silicone wi-

thout sliding. Verify that the back wall (14) is plumb, shim

if needed. Then, secure the back wall to the wall studs at

top with #8 x 1¾" screws (not included) in the previously

drilled holes.

IMPORTANT: HAND TIGHTEN ONLY. DO NOT

OVER-TIGHTEN THE SCREWS.

Quick tip 

Hold the bottom of the back wall

with your foot when fastening in

place.

13

Apply a bead of silicone on both sides of base (13) thres-

hold at 3/8" from the base side fastening flanges.

Apply silicone on both side of the back wall (14) just

before the wall side radius. The silicone applied on the

base and vertically on the back wall must overlap.

5

⅜"

Base

Back

wall

14

min.3/16"

max.3/8"

Stud

X fastener

It is critical for the side wall

installation to have at least ⅛'' and

no more than ⅜" between the stud

and the X fastener.

6.1

Check me!

6.3

Check me!

6.4

Check me!

Remove all walls from the structure.

Clean the shower base and apply a bead of silicone on

the threshold at 3/8" from the back fastening flange. Run

the bead of silicone the entire length of the base and 1''

on each side also.

6.2

Check me!

⅜"

1"

19

Install the side wall (15) that is opposed to the faucet.

Lift the wall approximately 3 inches above the thres-

hold of the base, push it completely against the back

wall then slide the side wall into position.

WIPE OFF EXCESS SILICONE

3

1

Side wall

Back wall

7

STEP Final installation of side walls

Install the side wall (15) with the faucet hole. Lift the

wall approximately 3 inches above the threshold of the

base, push it completely against the back wall then

slide the side wall into position.

WIPE OFF EXCESS SILICONE

3

1

Side wall

Back wall

7.1

Check me!

7.2

Check me!

7.3

Check me!

BEFORE CONTINUING,

VALIDATE THAT ALL

THE WALLS ARE LEVEL,

PLUMB AND SQUARE

20

7

STEP Final installation of side walls (cont'd)

Secure the walls to the wall studs with #8 x 1¾ "

screws (not included) in the previously drilled holes.

Also, secure the walls by the fastening anges on the

sides of the walls. Use the pre-dilled holes.

If needed, use shims to keep walls plumb, square

and leveled. (Cut shim excess)

IMPORTANT: HAND TIGHTEN ONLY. DO NOT

OVER-TIGHTEN THE SCREWS.

Check me!

Place the template in the corner of the shower where

you want to install your shelf.

Slide the template up until the points on the left and

right-hand side of the template are at the height you

want your shelf.

Use a pencil, marker or wax pencil to mark the spots

where the holes for the shelf will be drilled.

Drill the holes using a 9/64" drill bit.

8

STEP Marking and drilling the

glass shelf holes

Fold here

Drilling positions

Base

Side wall

THE SIDE WALLS SHOULD LINE UP WITH

THE BASE

?

Quick tip 

90°

La page est en cours de chargement...

MAAX 103411-300-502 Utile back wall 48 in. Guide d'installation

Ce manuel convient également à

MAAX 103411-300-502 Utile back wall 48 in. Guide d'installation

dans d''autres langues

Documents connexes

Autres documents