Raychem TOUCH 1500 EX Guide d'installation
- Taper
- Guide d'installation
Touch 1500-EX
User Interface Terminal for nVent RAYCHEM NGC Systems
Installation Instructions
Touch 1500-EX
installed in a panel
DESCRIPTION
The nVent RAYCHEM Touch 1500-EX is a panel mounted display
used in conjunction with other nVent RAYCHEM control and
monitoring devices. The Touch 1500-EX is rated IP 65 (Type 4X),
and can be mounted indoors or outdoors. The Touch 1500-EX kit
includes all hardware required for mounting in a suitable electrical
panel. Additional materials are required for electrical connections
and are detailed below. These instructions describe how to mount
the Touch 1500-EX in an electrical panel and are intended only for
qualified personnel experienced in panel construction.
CERTIFICATIONS / APPROVALS
• TYPE 4X, IP65 protection on front panel
• FCC Part15 Subpart B/ICES 003 Class A
• CE marking
Low Voltage Directive (2014/35/EU) EN 62368-1:2014 / A11:2017
EMC Directive (2014/30/EU) EN 55032:2015 EN 55035:2017
• Conforms to UL 62368-1, 2nd Ed, 2014-12-01; CAN/CSA C22.2
No. 62368-1-14, 2nd Ed, Issued: 2014-12-01; UL 60950-1, 2nd Edition,
2019-05-09 ; CAN/CSA C22.2 No. 60950-1-07, 2nd Edition, 2014-10
• ATEX Directive (2014/34/EU)
EN 60079-0:2017
EN 60079-11:2012
EN 60079-7: 2015 +A1:2018
• IECEx
IEC 60079-0 2017
IEC 60079-11 2012
IEC 60079-7, 5.1 Ed
II 3 G Ex ic ec IIC T4 Gc
General
Area of Use Ordinary (nonhazardous) and Class I Div. 2 / Zone 2 hazardous locations, indoors or outdoors (IP65, Type 4X)
Supply Voltage 12 -27VDC, 4A-1.5A respectively, AWG 16-20 (1.5 mm
2
- 0.5 mm
2
)
Operating Temperature –40°F to 140°F (–40°C to 60°C)
Min. Storage Temperature –40°F to 176°F (–40°C to 80°C)
Dimensions 16.61 in W x 13.31 in H x 2.68 in D (422 mm W x 338 mm H x 68 mm D)
Humidity Range 10 to 90% Non-Condensing
Wire rating 85°C or higher
Recommended Screw Torque 5.5 in lbs (0.62Nm)
Alarm Outputs
Transistor open collector outputs 5 – 30 Vdc with a max. sink current of 500 mA
Use to drive external relays Relays may be assigned for alarm outputs.
RoHS
KIT CONTENTS
Qty Description
1 Touch 1500-EX
16 6/32 in Kep nuts (locking nuts)
TOOLS REQUIRED
• Masking tape • 3/16" (5 mm) drill bit
• Metal file
• In-line torque wrench with 8 mm (5/16 in) socket
2 | nVent.com/RAYCHEM
Provide Suitable Panel Enclosure, and Determine Locations for Touch 1500-EX Assembly in Panel
1. Provide suitable panel enclosure
To protect its electronic components, the nVent Touch 1500-EX
must be mounted in a panel with a minimum IP32 (Type 1)
enclosure for non-hazardous indoor locations. An IP52 (Type 12)
or better enclosure is recommended. An IP54 (Type 4) or better
enclosure is required for hazardous locations. The Touch 1500-EX
assembly comes with a sealing gasket and hardware to mount
theenclosure.
Note: The Touch 1500-EX is designed for operation in ambient
temperatures from –40°F to 140°F (–40°C to 60°C). If the ambient
temperature is outside this range, a space heater and/or cooling fan
will be required in the panel.
2. Determine locations for the Touch 1500-EX assembly in the
electrical panel
The Touch 1500-EX should be located on the front of the panel
near eye level (for convenient viewing). The Touch 1500-EX
assembly is an electronic unit and must not be located where it
will be exposed to strong magnetic fields or excessive vibration.
Conditions of Safe Use in Hazardous (Explosive) Atmospheres
The equipment must be installed in a low risk mechanical danger
environment. The equipment shall only be used in an area of at
least pollution degree 2, as defined in IEC/EN 60664-1.
The equipment shall be installed in a back enclosure with tool
removable door or cover that provides a degree of protection not
less than IP54 in accordance with IEC/EN 60079-0 rated for
• Internal and external ambient of: –40°F to 140°F (–40°C to 60°C)
• ATEX / IECEx: Zone 2 or better
• US / CAN: Class I Div 2 or better
Provisions shall be made external to the equipment to provide
transient protection at a level not exceeding 140% at the power
supply terminals
Do not connect/disconnect equipment unless power has
been switched off or the area is known to be non-hazardous.
Ne débranchez pas l'equipement tant que l'alimentation est
coupée ou que la zone est connue pour être non dangereux.
• Use appropriately classified and listed Power Supply
(Limited Power Source, or LPS). Follow all applicable
wiring codes and regulations.
• Peripheral equipment must be suitable for the location
in which it is used.
• There are no non-incendive circuits or non-incendive
field wiring within or associated with the unit.
• Only technically qualified service personnel are
permitted to install or service the equipment.
• Do not disassemble the system - no user-serviceable
parts inside.
• Do not operate the equipment if it has been damaged.
• Utilisez une source d'alimentation correctement classée
et répertoriée (source dénergie limitée ou LPS). Suivez
tous les codes et normes de câblage applicables.
• L'équipement périphérique doit être adapté à
l'emplacement dans lequel il est utilisé.
• Il n'y a pas de circuits non incendiaires ni de câbles de
terrain non incendiaires à l'intérieur ou associés avec
léquipment.
• Seul le personnel qualifié est autorisé à installer ou à
entretenir l'équipement.
• Ne pas démontez le système - aucune pièce interne ne
peut être réparée par l'utilisateur.
• N'utilisez pas l'équipement s'il a été endommagé.
WARNING:
IMPORTANT:
LCD Display
Display LCD is a 15 in color XGA with integral LED backlight.
Touch Screen 5-wire resistive touch screen interface for user entry; compatible with glove use
Operating Temperature –40°F to 140°F (–40°C to 60°C). Enclosure heater recommended below 32°F (0°C)
Network Connection
Local/ Remote Port
nVent RAYCHEM RS-232/RS-485 ports may be used to communicate with host computers
(nVent RAYCHEM Supervisor Software) or DCS
Local RS-232 A non-isolated, 9 pin D sub male
Maximum cable length RS-232 Cable Length not to exceed 10' (3m)
Remote RS-485 Used to communicate to upstream devices such as a PLC or DCS 2-wire isolated shielded twisted pair.
Data Rate 9600 to 57600 baud.
Maximum cable length RS-485 Cable Length not to exceed 1200 m (4000 ft) at 9600 baud.
Field RS-485 Used to communicate with external devices, such as nVent RAYCHEM NGC-40 Bridge Module, Elexant 4010i,
Elexant 4020i, and RMM2.
Field RS-485 2-wire isolated shielded twisted pair
Data Rate Fixed at 9600 baud
Maximum cable length RS-485 Cable Length not to exceed 1200 m (4000 ft) at 9600 baud.
LAN 10/100 Base-T Ethernet port with Link and Activity Status LEDs on Port 1. Port 2 and Port 3 inactive.
USB Ports USB 2.0 Host port Type A receptacle on Ports 1 and 2. Ports 3 and 4 inactive.
C1
CB19
CB17
CB15
CB13
CB3
CB9
CB11
CB7
CB5
CB1
CB16
CB42
CB20
CB18
CB4
CB14
CB12
CB10
CB8
CB6
CB2
C2 C3 C4 C5 C6 C7 C8 C9 C10
CB23
CB25
CB27
CB29
CB21
CB26
CB28
CB30
CB22
CB24
CB31
CB33
CB35
CB37
CB39 CB40
CB36
CB32
CB34
CB38
1
3
5
7
9
19
17
15
13
11
29
27
25
23
21
39
37
35
33
31
2
4
6
8
10
12
14
16
18
20
30
28
26
24
22
32
34
36
38
40
PanelTouch 1500-EX
assembly location
Panel
door
Alarm
light
Conditions d'utilisation en toute sécurité dans des atmosphères
dangereuses (explosives)
Cet équipement doit être installé dans un environnement à faible
risque de dommages mécaniques.
Cet équipement doit être installé dans une armoire ou un panneau
classé pour les zones dangereuse comme suit:
• Ambiance interne et externe de: –40ºC à + 60ºC
• Indice de protection minimum IP54
• ATEX / IECEx: Zone 2 ou supérieur
• US / CAN: Class I Div 2 ou supérieur
• Ne peut être ouvert quà laide dun outil
nVent.com/RAYCHEM | 3
Cut Opening and Mount Touch 1500-EX on Front of Panel
1. Locate the Touch 1500-EX on front of panel
Locate the Touch 1500-EX assembly on the front of the panel at
a level convenient for viewing. Make sure the cover on the back
of the assembly will not interfere with existing panel hardware.
2. Prepare and mark the position of the display opening and
mounting holes
• Use the cut-out directions to lay out the opening for the
Touch 1500-EX display.
• Apply two layers of masking tape around the outer
perimeter of the intended opening to prevent scratching the
panel surface with the jigsaw.
3. Cut the display opening
Cut the opening for the Touch 1500-EX with a jigsaw using a
24TPI blade. Take care not to damage the panel door. Remove
all rough edges and burrs with a metal le before proceeding.
4. Drill the mounting holes
Drill the 16 holes with a 3/16" (5 mm) drill bit to mount the
Touch 1500-EX assembly in the panel.
Note: The following steps are most easily accomplished if the
panel door is on a horizontal surface.
5. Mount the user interface assembly onto the panel door
• Place the Touch 1500-EX assembly in position; the sixteen
studs go through the sixteen holes on the Touch 1500-EX
assembly mounting plate (see gure below).
• Place the supplied 6/32 in Kep nuts on each of the sixteen
mounting studs. Fasten only hand tight.
• Look at the front of the panel, and align the Touch 1500-EX
assembly so it is level (loosen nuts if necessary to
reposition the Touch 1500-EX assembly).
• After the display is properly positioned, tighten the nuts to
0.62 Nm (5.5 in/lb) of torque using a 3/16" (5 mm) in-line
torque wrench. Do not overtighten and risk damage to
hardware.
• Tighten Kep nuts in the sequence shown for proper sealing.
Cutting
Area
14.31 in
11.00 in
Note: Cutting the opening for the display is a craft sensitive
procedure; if it is not done correctly, the panel door can
be damaged. The procedure for laying out and cutting the
opening for the display must be undertaken with care, and by
personnel qualied and experienced in panel construction.
Panel door
Touch 1500-EX display
with sealing gasket
Touch 1500-EX
display
Inside of
panel door
Inside of
panel door
Touch 1500-EX
display
9 11
10 2
15 31
4 1612
5
8 6
13 14
7
4 | nVent.com/RAYCHEM
Touch 1500-EX Cut Out Dimensions in (mm)
16X
.170 (4.3)
3.500 (88.9) 3.000 (76.2) 3.000 (76.2) 3.500 (88.9)
0.200 (5.1)
3.000 (76.2)
3.000 (76.2)
2.756 (70.0)
2.756 (70.0)
1.236 (31.4) 1.236 (31.4)
.250 (6.4)
14.972 (380)
11.112 (282)
nVent.com/RAYCHEM | 5
Front ViewSide View Side View
Bottom View
Grounding Terminal
Top View
Touch 1500-EX Connection Diagram
6 | nVent.com/RAYCHEM
Open Collector
ISOGND1
RS-485
TERM
PU
PD
TERM
PU
PD
DATA2-
ISOGND2
DATA1-
DATA1+
DATA2+
GND
VIN
3
2
1
4
RESET
TX
RX
TX
RX
GND
VIN
3
2
1
4
Door Mounted
+24 Vdc
This relay is shown
in the energized position
without an alarm condition.
+24 Vdc
0 Vdc
GND (–)
NO
C
NC
3
4
Alarm
Lamp
24 Vdc Lamp
IDEC SWITCH/
LAMP
1
2
Relay Driver Output
Alarm
Relay
Jumper switch
terminals 1, 4 and x2
Ethernet Ports
1 2 (inactive) 3 (inactive)
Connect Power
Install Common Alarm Light and Alarm Relays
Connect 24 Vdc to the male power connection fitting located on
the left side of the Touch 1500-EX. Make sure to connect the
grounding terminal. Ensure the cables are routed through
the cable clamp as shown.
Note: The Touch 1500-EX is rated for 12 -27 Vdc. Since the
NGC-40 modules are rated for 24 Vdc, we have used
this voltage to also power the Touch 1500-EX. As a result, the
recommend alarm relays and lights detailed in the “Additional
Materials” are rated for 24 Vdc.
Provision shall be made external to the equipment to provide
transient protection at a level not exceeding 140% at the power
supply terminals.
Mount the alarm relay on a DIN rail inside the panel enclosure.
Mount the Alarm light on the panel’s door below the touch screen.
Per the below drawing, bring 24 Vdc to the Relay Driver Output at the
bottom of the touch screen, to the alarm relay and alarm light.
Per the below drawing, wire between the Relay Driver Output, alarm
relay, and alarm light.
DETAIL A
SCALE 2 : 1
nVent.com/RAYCHEM | 7
Open Collector
ISOGND1
RS-485
TERM
PU
PD
TERM
PU
PD
DATA2-
ISOGND2
DATA1-
DATA1+
DATA2+
GND
VIN
3
2
1
4
RESET
TX
RX
TX
RX
RS-232 RS-232
CFast
TX
RX
TX
RX
Communication
The Touch 1500-EX has two isolated RS-485 ports located at
thebottom.
Field Side Port (DATA 1 +/-)
The RS-485 port labeled “RS-485-1” is the field side
port that is used to communicate with ModBus devices
(ie. NGC-40 Bridge Module, Elexant 4010i, Elexant 4020i,
and RMM2).
Remote Port (DATA 2 +/-) – Optional
The RS-485 port labeled “RS-485-2” is the Host side port that
is used to communicate with to a host computer (using nVent
RAYCHEM Supervisory Software) or to a DCS.
Local Host Port (RS-232) – Optional
The RS-232 port labeled "RS-232 1" is the RS-232 port that can
be used as local Host port that is used tocommunicate with to
a host computer (using nVent RAYCHEM Supervisory Software).
If the RS-232 port is utilized, the supplied female to female, 9-pin
null modem adaptor cable must be used.
RS-485 configuration switches
The conguration switches are found on the bottom side of
the Touch 1500-EX. Refer to the table below for settings.
Position
Switch On Off Comments
Pull-down
(PD)
(As-shipped default) RS-485 network “–”
signal is forced to a determinate state
when idle.
RS-485 network “–” signal is
not forced to a determinate
state when idle.
One device (typically this Touch 1500-EX) on the
RS-485 network should force the network “-“ signal to a
determinate state.
Pull-up (PU) (As-shipped default) RS-485 network “+”
signal is forced to a determinate state
when idle.
RS-485 network “+” signal is
not forced to a determinate
state when idle.
One device (typically this Touch 1500-EX) on the
RS-485 network should force the network “+“ signal to
a determinate state.
Termination
(TERM)
(As-shipped default) RS-485 network is
terminated with 120-ohm resistor.
RS-485 network is not termi-
nated.
Terminate the device (Touch 1500-EX or other) that is
at each end of the RS-485 network, for a total of two
terminated devices. No other devices on the network
should be terminated.
Reset
nVent.com/RAYCHEM
©2021 nVent. All nVent marks and logos are owned or licensed by nVent Services GmbH or its aliates. All other trademarks are the property of their respective owners.
nVent reserves the right to change specications without notice.
RAYCHEM-IM-H61098-Touch1500EX-EN-2104
North America
Tel +1 800 545 6258
Fax +1 800 527 5703
Europe, Middle East, Africa
Tel +32 16 213 511
Fax +32 16 21 36 04
Asia Pacific
Tel +86 21 2412 1688
Fax +86 21 5426 3167
Latin America
Tel +1 713 868 4800
Fax +1 713 868 2333
Reset
Reset switch
Product Label
The Reset switch can be found on the bottom of the Touch 1500-EX.
A pointed object is required to press the reset switch and restart the
Touch 1500 software.
WARNING: Explosion Hazard - Do not disconnect equipment unless power has been switched off or the area is known to be
non-hazardous. No serviceable parts inside.
AVERTISSEMENT : Risque d'explosion - Ne débranchez pas l'équipement que l'alimentation est coupée ou que la zone est connue
pour être non dangereux. Aucune pièce interne réparable par l'utilisateur.
Tested to comply with FCC Class A standards. CAN ICES3(A)/NMB3(A).
Power Rating: 12–27 VDC 4A - 1.5A
UL 21 ATEX 2493X IECEx UL 21.0039X
II 3 G Ex ic ec IIC T4 Gc
Class I Div. 2 Groups A, B, C, D, T4
–40°C ≤ Ta ≤ 60°C
© 2021 nVent, 899 Broadway, Redwood City, CA 94063
Made in USA H61097-EN 2104
nVent.com/RAYCHEM
Part No.: R9075-15
Serial No.:
TOUCH 1500-Ex
RoHS
I.T.E for Haz. Loc.
E516513
The Touch 1500-EX contains no user-serviceable parts. Contact your nVent representative for serviceand a return authorization number if required.
The touch screen area of the Touch 1500-EX may be cleaned with a damp cloth. Typical window cleaning agents may be applied to aid in the removal of
dirt, dust and grease. Do not use abrasive cleaners.
Servicing
Cleaning
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Raychem TOUCH 1500 EX Guide d'installation
- Taper
- Guide d'installation
dans d''autres langues
Documents connexes
-
Raychem NGC UIT3 EX Guide d'installation
-
-
-
-
-
-
-
-
-
