daltile 0000HDCHIPBK10 Guide d'installation

Taper
Guide d'installation
Chamber Cli Sterling
18 in. x 18 in. tile shown in brick pattern
Installation of
FLOOR & LARGE
FORMAT TILE
Tile may be
installed over most
structurally sound
substrates.
Make sure surface
is clean, smooth,
dry and free of
wax, soap scum
and grease.
Any damaged,
loose or uneven
areas must be
repaired, patched
and leveled.
Remove any
moldings, trim,
appliances or
anything that
could interfere with
installation.
Doorjambs may be
undercut for tile to
slip under.
Mark the center point of
all four walls.
Snap chalk lines
between the center
points of opposite walls.
(Adjust if necessary.)
Using tile spacers, lay out
a row of loose tiles along
the center lines in both
directions. Leave space for
uniform joints.
TIP: If cuts leave tiles
smaller than half of their
original size, adjust the
center line by snapping a
new line a half tile closer to
the wall. Repeat along other
center line if necessary.
Divide the room into smaller
grids (approx. 2 ft. x 3 ft.) by
snapping additional lines
parallel to center lines.
STEP 1: SURFACE PREPARATION
1
STEP 2: LAYOUT
2
INSTALLATION INSTRUCTIONS | FLOOR & LARGE FORMAT TILE | PAGE 1 of 4
CONTINUED ON NEXT PAGE
Chamber Cli Sterling
18 in. x 18 in. tile shown in brick pattern
Installation of
FLOOR & LARGE
FORMAT TILE
Carefully measure
tiles and mark
with a pencil or
felt-tip pen.
Make straight or
diagonal cuts with
a tile cutter, curved
cuts with a nipper
(chipping away
small pieces for
best results), and
full-length curved
cuts with a rod saw.
Smooth out sharp-
cut edges with a
carborundum stone.
STEP 4: CUTTING TILESTEP 3: APPLYING ADHESIVE
3 4
Mix only enough adhesive or mortar
to be used within 30 minutes.
Using the type of trowel
recommended on the adhesive
package, spread a 1/4 in. coat on the
surface of one grid area, using the
flat side of the trowel.
NOTE: Do not cover guidelines or
a larger area than can be set in 15
minutes.
Use the notched side of trowel to
comb adhesive into standing ridges
by holding trowel at a 45° angle.
Remove excess adhesive, leaving a
uniform, ridged setting bed.
For large format tiles, butter the
backside of the tile to ensure proper
full-coverage. Use a medium bed
mortar for tiles with a dimensional
length greater than 15 inches on any
one side.
NOTE: 90% mortar contact is
recommended.
INSTALLATION INSTRUCTIONS | FLOOR & LARGE FORMAT TILE | PAGE 2 of 4
CONTINUED ON NEXT PAGE
Chamber Cli Sterling
18 in. x 18 in. tile shown in brick pattern
Installation of
FLOOR & LARGE
FORMAT TILE
Using the instructions on the
package, make enough grout to
use in about 30 minutes.
Remove tile spacers and spread grout on
the tile surface, forcing down into joints
with a rubber grout float or squeegee.
Tilt the float at a 45° angle and remove
excess grout from surface immediately
with the edge of float.
Tilt it at a 90° angle and scrape it
diagonally across tiles.
Wait 15–20 minutes for grout to set
slightly, then use a damp sponge to clean
grout residue from surface and smooth
the grout joints, rinsing sponge often.
Let dry until grout is hard and haze forms
on tile surface, then polish with a soft
cloth and wait 72 hours for heavy use.
NOTE: Don’t apply sealers or polishes for
three weeks, and then only in accordance
with manufacturer’s recommendations.
STEP 6: GROUTING JOINTSSTEP 5: SETTING TILE
5 6
Install tiles in the center, one grid
at a time. Finish each grid before
moving to the next. Start with the
first tile in the corner of the grid
and work outward. Set tiles one at a
time using a slight twisting motion.
NOTE: Don’t slide tiles into place.
Insert tile spacers, as each tile is set,
or leave equal joints between tiles.
Fit perimeter tiles in each
grid last, leaving 1/4 in. gap
between tile and wall.
When finished, tap in all tiles with a
rubber mallet or hammer and wood
block, to ensure a good bond and
level plane.
Remove excess adhesive from joints
with a putty knife, and from tile with
a damp sponge.
Do not walk on tiles until they are
set (usually in 24 hours).
INSTALLATION INSTRUCTIONS | FLOOR & LARGE FORMAT TILE | PAGE 3 of 4
CONTINUED ON NEXT PAGE
Chamber Cli Sterling
18 in. x 18 in. tile shown in brick pattern
Installation of
FLOOR & LARGE
FORMAT TILE
Back-butter spreading of a bond coat
to the back of a ceramic tile
before placing the tile to
ensure a strong bond with
the thin-set mortar.
Balanced cuts perimeter tile cut at equal
size and installed on
opposite sides of an area;
also, equally sized cuts on
each side of a miter.
Butt joint
a plain square joint
between two members
with no grout joint.
Grout
a mix used for filling tile
joints, commonly based
of cement.
Mortar a mixture of cement paste
and fine aggregate used to
bond masonry together.
Plumb perpendicular to true level.
Substrate the underlying support for
a ceramic tile installation
GLOSSARY OF TERMS
A
STEP 7: INITIAL CLEANING
7
The complete removal of grout and
construction dirt after products
have been installed will improve
daily maintenance.
Clean successfully by scrubbing the
installation with hot water and a
pH neutral liquid cleaner (soapless),
followed by a thorough rinsing, then
remove the rinse water with a wet
vacuum or dry toweling.
If some residue remains, further
cleaning will need to be done
in consultation with the grout
manufacturer.
For more aggressive cleaning, floor
scrubbing machines equipped
with nylon pads or brushes should
be used. Wet vacuuming of the
suspended dirt and grout is
recommended.
INSTALLATION INSTRUCTIONS | FLOOR & LARGE FORMAT TILE | PAGE 3 of 4
LEGAL
B
ATTENTION / ATENCIÓN / ATTENTION
Do not dry cut using motorized equipment due to the
potential for exposure to harmful silica dust. Use a wet saw
or a score and snap tool when cutting is necessary during
the installation process.
No corte en seco usando equipo motorizado debido a la
posibilidad de
exposición a polvo dañino de sílice. En caso de que sea
necesario cortar durante el proceso de instalación, usar una
sierra de corte en húmedo o una herramienta cortadora
manual.
Ne pas couper à sec à l’aide d’un équipement motorisé en
raison du risque d’exposition à la poussière de silice nuis-
ible. Utiliser une scie à eau ou un outil à inciser et rompre
lorsqu’il faut couper pendant le processus d’installation.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

daltile 0000HDCHIPBK10 Guide d'installation

Taper
Guide d'installation

dans d''autres langues