Wacker Neuson BS50-2 Manuel utilisateur

5000184099 08 0712

Operator’s Manual

Vibratory Rammer

BS 50-2

Notice d’Emploi

Pilonneuse

5000184099

Copyright

notice

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the machine. Any

other type of reproduction is prohibited without express written permission from

Wacker Neuson Production Americas LLC.

Any type of reproduction or distribution not authorized by Wacker Neuson Production

Americas LLC represents an infringement of valid copyrights. Violators will be

prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their respective owners.

Manufacturer

Wacker Neuson Production Americas LLC

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Original

instructions

This Operator’s Manual presents the original instructions. The original language of this

Operator’s Manual is American English.

5000184075 08 0712

BS 50-2 Foreword

wc_tx001354gb.fm 3

Foreword

SAVE THESE INSTRUCTIONS—This manual contains important instructions for

the machine models below. These instructions have been written expressly by

Wacker Neuson Production Americas LLC and must be followed during installation,

operation, and maintenance of the machines.

;

Machine

documentation

 From this point forward in this documentation, Wacker Neuson Production

Americas LLC will be referred to as Wacker Neuson.

 Keep a copy of the Operator’s Manual with the machine at all times.

 Use the separate Parts Book supplied with the machine to order replacement

parts.

 Refer to the separate Repair Manual for detailed instructions on servicing and

repairing the machine.

 If you are missing any of these documents, please contact Wacker Neuson to

order a replacement or visit www.wackerneuson.com.

 When ordering parts or requesting service information, be prepared to provide

the machine model number, item number, revision number, and serial number.

Expectations

for

information in

this manual

 This manual provides information and procedures to safely operate and

maintain the above Wacker Neuson model(s). For your own safety and to

reduce the risk of injury, carefully read, understand, and observe all instructions

described in this manual.

 Wacker Neuson expressly reserves the right to make technical modifications,

even without notice, which improve the performance or safety standards of its

machines.

 The information contained in this manual is based on machines manufactured

up until the time of publication. Wacker Neuson reserves the right to change

any portion of this information without notice.

CALIFORNIA

Proposition

65 Warning

Engine exhaust, some of its constituents, and certain vehicle components, contain

or emit chemicals known to the State of California to cause cancer and birth

defects or other reproductive harm.

Machine Item Number Revision Machine Item Number Revision

BS 50-2 0009384 Rev 121,

Rev 200+

BS 50-2 0620048 Rev 115,

Rev 200+

BS 50-2 0009410 Rev 121,

Rev 200+

BS 50-2 0620609 Rev 100+

BS 50-2 0009411 Rev 121,

Rev 200+

BS 50-2 0620610 Rev 100+

BS 50-2 0009413 Rev 121,

Rev 200+

BS 50-2 0620733 Rev 100+

BS 50-2 0620025 Rev 115,

Rev 200+

—— —

Foreword BS 50-2

4 wc_tx001354gb.fm

Laws

pertaining to

spark

arresters

NOTICE: State Health Safety Codes and Public Resources Codes specify that in

certain locations spark arresters be used on internal combustion engines that use

hydrocarbon fuels. A spark arrester is a device designed to prevent accidental

discharge of sparks or flames from the engine exhaust. Spark arresters are

qualified and rated by the United States Forest Service for this purpose. In order to

comply with local laws regarding spark arresters, consult the engine distributor or

the local Health and Safety Administrator.

Manufacturer’s

approval

This manual contains references to approved parts, attachments, and

modifications. The following definitions apply:

 Approved parts or attachments are those either manufactured or provided by

Wacker Neuson.

 Approved modifications are those performed by an authorized Wacker

Neuson service center according to written instructions published by Wacker

Neuson.

 Unapproved parts, attachments, and modifications are those that do not

meet the approved criteria.

Unapproved parts, attachments, or modifications may have the following

consequences:

 Serious injury hazards to the operator and persons in the work area

 Permanent damage to the machine which will not be covered under warranty

Contact your Wacker Neuson dealer immediately if you have questions about

approved or unapproved parts, attachments, or modifications.

Original Declaration of Conformity

2012-CE-BS50-2-2i_en.fm

EC Declaration of Conformity

Manufacturer

Wacker Neuson Production Americas LLC, N92W15000 Anthony Avenue,

Menomonee Falls, Wisconsin 53051 USA

Product

Product category

Product function

Item number

Net installed power

Measured sound power level

Guaranteed sound power level

BS 50-2, BS 50-2i

Vibratory Rammer

To compact soil

0009410, 0009411, 0009413, 0620025, 0620048,

0009412, 0009414, 0009416, 0009473, 0620026,

5200003696

1,7 kW

106 dB(A)

108 dB(A)

Conformity Assessment Procedure

According to ANNEX VIII

Notified Body

Lloyds Register Quality Assurance Limited (Notified Body No 0088)

71 Fenchurch Street, London EC3M 4BS, United Kingdom

Directives and Standards

We hereby declare that this product meets and complies with the relevant regulations and

requirements of the following directives and standards:

2006/42/EC, 2000/14/EC, 2004/26/EC, 2004/108/EC, EN 500-1, EN 500-4

Authorized Person for Technical Documents

Axel Häret, Wacker Neuson Produktion GmbH & Co. KG, Preußenstraße 41, 80809 München

Menomonee Falls, WI, USA, 28.06.12

William Lahner

Managing Director

Paul Sina

Manager, Product Engineering

Todd Lutz

Director of Business Development

Table of Contents

BS 50-2

wc_bo5000184075_08TOC.fm

7

Foreword 3

EC Declaration of Conformity 5

1 Safety Information 9

1.1 Signal Words Used in this Manual ....................................................... 9

1.2 Machine Description and Intended Use ............................................. 10

1.3 Safety Guidelines for Operating the Machine ..................................... 11

1.4 Safety Guidelines for Lifting the Machine ........................................... 12

1.5 Service Safety .................................................................................... 13

1.6 Operator Safety while Using Internal Combustion Engines ............... 15

2 Labels 16

2.1 Label Locations .................................................................................. 16

2.2 Label Meanings .................................................................................. 17

3 Lifting and Transporting 21

3.1 Lifting the Rammer ............................................................................. 21

3.2 Transporting the Rammer .................................................................. 22

4 Operation 23

4.1 Preparing the Machine for First Use ................................................... 23

4.2 Recommended Fuel ........................................................................... 24

4.3 Refueling the Machine ........................................................................ 25

4.4 Position of the Operator ..................................................................... 26

4.5 Before Starting ................................................................................... 26

4.6 Starting, Operating, and Stopping the Machine ................................. 27

4.7 Emergency Shutdown Procedure ....................................................... 29

4.8 Optional Equipment ............................................................................ 29

5 Maintenance 30

5.1 Maintaining the Emission Control System .......................................... 30

5.2 Periodic Maintenance Schedule ......................................................... 31

5.3 Servicing the Air Cleaner .................................................................... 32

5.4 Checking the Fuel Lines and Fittings ................................................. 34

5.5 Maintaining the Shoe Hardware ......................................................... 34

5.6 Inspecting the Machine ...................................................................... 35

Table of Contents

BS 50-2

wc_bo5000184075_08TOC.fm

8

5.7 Cleaning the Engine Cooling Fins .......................................................36

5.8 Cleaning and Checking the Spark Plug ...............................................37

5.9 Checking and Changing the Ramming System Oil .............................38

5.10 Adjusting the Idle Speed .....................................................................40

5.11 Inspecting and Cleaning the Fuel Filter ...............................................41

5.12 Long-Term Storage .............................................................................42

5.13 Machine Disposal / Decommissioning .................................................43

6 Basic Troubleshooting 44

7 Technical Data 45

7.1 Rammer ...............................................................................................45

7.2 Sound Measurements .........................................................................46

7.3 Vibration Measurements .....................................................................46

7.4 Dimensions ..........................................................................................47

8 Emission Control Systems Information and Warranty 49

8.1 Emission Control System Background Information .............................49

8.2 Limited Defect Warranty for Wacker Neuson Emission Control

Systems ...............................................................................................50

wc_si000688gb.fm

9

BS 50-2 Safety Information

1 Safety Information

1.1 Signal Words Used in this Manual

This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE

signal words which must be followed to reduce the possibility of personal injury,

damage to the equipment, or improper service.

NOTICE: Used without the safety alert symbol, NOTICE indicates a situation

which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

f Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

f To avoid death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

f To avoid possible death or serious injury from this type of hazard, obey all safety

messages that follow this signal word.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

f To avoid possible minor or moderate injury from this type of hazard, obey all

safety messages that follow this signal word.

wc_si000688gb.fm

10

Safety Information BS 50-2

1.2 Machine Description and Intended Use

This machine is a vibratory rammer. The Wacker Neuson Rammer consists of a

gasoline or diesel engine, a clutch, a fuel tank, a spring-loaded ramming system, a

ramming shoe, and a handle. The engine transmits power through the ramming

system and ramming shoe, generating percussive impact force to compact soil.

The operator guides and controls the machine from behind using the handle.

This machine is intended to be used for compacting cohesive, mixed, and granular

soils in confined areas.

This machine has been designed and built strictly for the intended use described

above. Using the machine for any other purpose could permanently damage the

machine or seriously injure the operator or other persons in the area. Machine

damage caused by misuse is not covered under warranty.

The following are some examples of misuse:

 Using the machine as a ladder, support, or work surface

 Using the machine to carry or transport passengers or equipment

 Using the machine as a hammer or for other demolition work

 Attaching the machine to any other machine

 Operating the machine outside of factory specifications

 Operating the machine in a manner inconsistent with all warnings found on the

machine and in the Operator’s Manual

This machine has been designed and built in accordance with the latest global

safety standards. It has been carefully engineered to eliminate hazards as far as

practicable and to increase operator safety through protective guards and labeling.

However, some risks may remain even after protective measures have been taken.

They are called residual risks. On this machine, they may include exposure to:

 Heat, noise, exhaust, and carbon monoxide from the engine

 Fire hazards from improper refueling techniques

 Fuel and its fumes

 Personal injury from improper lifting techniques or operating techniques

To protect yourself and others, make sure you thoroughly read and understand the

safety information presented in this manual before operating the machine.

wc_si000688gb.fm

11

BS 50-2 Safety Information

1.3 Safety Guidelines for Operating the Machine

Operator

training

Before operating the machine:

 Read and understand the operating instructions contained in all manuals

delivered with the machine.

 Familiarize yourself with the location and proper use of all controls and safety

devices.

 Contact Wacker Neuson for additional training if necessary.

When operating this machine:

 Do not allow improperly trained people to operate the machine. People

operating the machine must be familiar with the potential risks and hazards

associated with it.

Operator

qualifications

Only trained personnel are permitted to start, operate, and shut down the machine.

They also must meet the following qualifications:

 have received instruction on how to properly use the machine

 are familiar with required safety devices

The machine must not be accessed or operated by:

 children

 people impaired by alcohol or drugs

Application

area

Be aware of the application area.

 Keep unauthorized personnel, children, and pets away from the machine.

 Remain aware of changing positions and the movement of other equipment and

personnel in the application area/job site.

Be aware of the application area.

 Do not operate the machine in areas that contain flammable objects, fuels, or

products that produce flammable vapors.

Safety

devices,

controls, and

attachments

Only operate the machine when:

 All safety devices and guards are in place and in working order.

 All controls operate correctly.

 The machine is set up correctly according to the instructions in the Operator’s

Manual.

 The machine is clean.

 The machine’s labels are legible.

To ensure safe operation of the machine:

 Do not operate the machine if any safety devices or guards are missing or

inoperative.

 Do not modify or defeat the safety devices.

 Only use accessories or attachments that are approved by Wacker Neuson.

wc_si000688gb.fm

12

Safety Information BS 50-2

Safe

operating

practices

When operating this rammer:

 Remain aware of the rammer’s moving parts. Keep hands, feet, and loose

clothing away from the rammer’s moving parts.

 When working near the edges of pits, slopes, trenches and platforms, always

operate the rammer in such a way that there is no possibility of it tipping over or

falling in.

When operating this rammer:

 Do not operate a rammer in need of repair.

 Do not tamper with or disable the function of operating controls.

 Do not leave the rammer running unattended.

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while operating this

machine:

 Close-fitting work clothes that do not hinder movement

 Safety glasses with side shields

 Hearing protection

 Safety-toed footwear

After Use

 Stop the engine when the machine is not being operated.

 Close the fuel valve on engines equipped with one when machine is not being

operated.

 Ensure that the machine will not tip over, roll, slide, or fall when not being

operated.

 Store the machine properly when it is not being used. The machine should be

stored in a clean, dry location out of the reach of children.

1.4 Safety Guidelines for Lifting the Machine

When lifting the machine:

 Make sure slings, chains, hooks, ramps, jacks, forklifts, cranes, hoists, and any

other type of lifting device used is attached securely and has enough weight-

bearing capacity to lift or hold the machine safely. See section Technical Data

for machine weight.

 Remain aware of the location of other people when lifting the machine.

 Only use the lifting points and tie-downs described in the Operator’s Manual.

 Make sure the transporting vehicle has sufficient load capacity and platform size

to safely transport the machine.

To reduce the possibility of injury:

 Do not stand under the machine while it is being lifted or moved.

 Do not get onto the machine while it is being lifted or moved.

wc_si000688gb.fm

13

BS 50-2 Safety Information

1.5 Service Safety

Service

training

Before servicing or maintaining the machine:

 Read and understand the instructions contained in all manuals delivered with

the machine.

 Familiarize yourself with the location and proper use of all controls and safety

devices.

 Only trained personnel shall troubleshoot or repair problems occurring with the

machine.

 Contact Wacker Neuson for additional training if necessary.

When servicing or maintaining this machine:

 Do not allow improperly trained people to service or maintain the machine.

Personnel servicing or maintaining the machine must be familiar with the

associated potential risks and hazards.

Precautions

Follow the precautions below when servicing or maintaining the machine.

 Read and understand the service procedures before performing any service to

the machine.

 All adjustments and repairs must be completed before operating the machine.

Do not operate the machine with a known problem or deficiency.

 All repairs and adjustments shall be completed by a qualified technician.

 Turn off the machine before performing maintenance or making repairs.

 Remain aware of the machine’s moving parts. Keep hands, feet, and loose

clothing away from the machine’s moving parts.

 Reinstall the safety devices and guards after repair and maintenance

procedures are complete.

Machine

modifications

When servicing or maintaining the machine:

 Use only accessories/attachments that are approved by Wacker Neuson.

When servicing or maintaining the machine:

 Do not defeat safety devices.

 Do not modify the machine without the express written approval of Wacker

Neuson.

Replacing

parts and

labels

 Replace worn or damaged components.

 Replace all missing and hard-to-read labels.

 When replacing electrical components, use components that are identical in

rating and performance to the original components.

 When replacement parts are required for this machine, use only Wacker

Neuson replacement parts or those parts equivalent to the original in all types of

specifications, such as physical dimensions, type, strength, and material.

wc_si000688gb.fm

14

Safety Information BS 50-2

Cleaning

When cleaning and servicing the machine:

 Keep the machine clean and free of debris such as leaves, paper, cartons, etc.

 Keep the labels legible.

When cleaning the machine:

 Do not clean the machine while it is running.

 Never use gasoline or other types of fuels or flammable solvents to clean the

machine. Fumes from fuels and solvents can become explosive.

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while servicing or

maintaining this machine:

 Close-fitting work clothes that do not hinder movement

 Safety glasses with side shields

 Hearing protection

 Safety-toed footwear

In addition, before servicing or maintaining the machine:

 Tie back long hair.

 Remove all jewelry (including rings).

Safe service

practices

 Do not alter engine speeds. Run the engine only at speeds specified in

Technical Data.

 Do not operate the machine without an air cleaner.

 Disconnect the spark plug before servicing to avoid accidental start-up.

 Do not crank a flooded engine with the spark plug removed. Fuel trapped in the

cylinder will squirt out the spark plug opening.

 Do not test for spark if the engine is flooded or the smell of gasoline is present.

A stray spark could ignite the fumes.

wc_si000688gb.fm

15

BS 50-2 Safety Information

1.6 Operator Safety while Using Internal Combustion Engines

Operating

safety

When running the engine:

 Keep the area around exhaust pipe free of flammable materials.

 Check the fuel lines and the fuel tank for leaks and cracks before starting the

engine. Do not run the machine if fuel leaks are present or the fuel lines are

loose.

When running the engine:

 Do not smoke while operating the machine.

 Do not run the engine near sparks or open flames.

 Do not touch the engine or muffler while the engine is running or immediately

after it has been turned off.

 Do not operate a machine when its fuel cap is loose or missing.

 Do not start the engine if fuel has spilled or a fuel odor is present. Move the

machine away from the spill and wipe the machine dry before starting.

Refueling

safety

When refueling the engine:

 Clean up any spilled fuel immediately.

 Refill the fuel tank in a well-ventilated area.

 Reinstall the fuel tank cap after refueling.

 Do not smoke.

 Do not refuel a hot or running engine.

 Do not refuel the engine near sparks or open flames.

 Use suitable tools for refueling (for example, a fuel hose or funnel).

 Do not refuel if the machine is positioned in a truck fitted with a plastic bed liner.

Static electricity can ignite the fuel or fuel vapors.

WARNING

Internal combustion engines present special hazards during operation and fueling.

Failure to follow the warnings and safety standards could result in severe injury or

death.

f Read and follow the warning instructions in the engine owner’s manual and the

safety guidelines below.

DANGER

Exhaust gas from the engine contains carbon monoxide, a deadly poison.

Exposure to carbon monoxide can kill you in minutes.

f NEVER operate the machine inside an enclosed area, such as a tunnel, unless

adequate ventilation is provided through such items as exhaust fans or hoses.

wc_si000408gb.fm

16

Labels BS 50-2

2 Labels

2.1 Label Locations

wc_si000408gb.fm

17

BS 50-2 Labels

2.2 Label Meanings

Wacker Neuson machines use international pictorial labels where needed. These

labels are described below.

A

To start the machine:

1. Move the throttle to the IDLE position.

2. Push the purge bulb 10 times.

3. Close the choke.

4. Pull the starter rope until engine starts.

5. Move the throttle to the FAST position.

To stop the machine:

1. Move the throttle past the SLOW position.

Warning! To reduce the risk of hearing loss, always wear

hearing protection when operating this machine.

Read the Operator’s Manual.

Danger!

Asphyxiation hazard.

 Engines emit carbon monoxide.

 Do not run the machine indoors or in an enclosed area

unless adequate ventilation, through such items as

exhaust fans or hoses, is provided.

 No sparks, flames, or burning objects near the

machine.

 Stop the engine before refueling.

This label is molded into the cover. If the label becomes

illegible, the cover must be replaced. Refer to the Parts

Book for ordering information.

wc_si000408gb.fm

18

Labels BS 50-2

D

Warning!

Springs are compressed. Release cover slowly to avoid

spring ejection.

See the Repair Manual for proper disassembly

instructions.

E

Move lever forward to stop machine. Move lever

backward to run machine.

This label is molded into the cover. If the label becomes

illegible, the cover must be replaced. Refer to the Parts

Book for ordering information.

F

For optimal control, performance, and minimal hand/arm

vibration, grasp handle as shown.

Read the Operator’s Manual.

This label is molded into the cover. If the label becomes

illegible, the cover must be replaced. Refer to the Parts

Book for ordering information.

G

Guaranteed sound power level in dB(A).

115416

wc_si000408gb.fm

19

BS 50-2 Labels

H

The air intake system is equipped with a filter indicator,

which indicates when a filter change is required.

Replace main paper filter element when yellow plunger

of the indicator appears in or near the red line.

I

A nameplate listing the model number, item number,

revision number, and serial number is attached to each

unit. Please record the information found on this name-

plate so it will be available should the nameplate

become lost or damaged. When ordering parts or

requesting service information, you will always be asked

to specify the model number, item number, revision

number, and serial number of the unit.

L

This engine is certified to operate on regular unleaded

gasoline mixed with two cycle oil at 50:1–100:1 ratio.

Read the Operator’s Manual.

Emission control information

This engine is certified to operate on regular unleaded

gasoline mixed with two cycle oil at 50:1–100:1 ratio

Displacement 80cc

Exhaust emissions control system: OC

Engine family: CW1XS.0805CA

This engine meets U.S. EPA exhaust regulations for

2012

This equipment meets U.S. EPA evaporative regulations

using certified components

Emission compliance period: 300 hours (heavy use)

wc_si000408gb.fm

20

Labels BS 50-2

M

This rammer engine requires a two-cycle gasoline/oil

mixture (50:1).

With Wacker Neuson 2-cycle or other fully synthetic oil

meeting the NMMA TC-W3, JASO FD, or ISO-L-EGD

specification, a ratio from 50:1 to 100:1 can be used.

This label is molded into the cover. If the label becomes

illegible, the cover must be replaced. Refer to the Parts

Book for ordering information.

N

Turtle = Idle/slow engine speed

Rabbit = Full/fast engine speed

This label is molded into the cover. If the label becomes

illegible, the cover must be replaced. Refer to the Parts

Book for ordering information.

O

Move the throttle to the IDLE position.

Close the choke.

P

WARNING

Operation of this equipment may create sparks that can

start fires around dry vegetation. A spark arrester may

be required. The operator should contact local fire

agencies for laws or regulations relating to fire

prevention requirements.

--

This machine may be covered by one or more patents.

170731

50:1

:

1

181641

2

WARNING

Operation of This Equipment May Create Sparks That Can Start Fires Around Dry

Vegetation. A Spark Arrestor May be Required. The Operator Should Contact Local

Fire Agencies For Laws or Regulations Relating to Fire Prevention Requirements.

Per CAL. PRC. CODE

La page charge ...

Wacker Neuson BS50-2 Manuel utilisateur

Wacker Neuson BS50-2 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents