Edimax EW-7889WAX Wireless Adapters Guide d'installation
- Taper
- Guide d'installation
EW‐7889WAX
EW‐7689WTX
QuickInstallationGuide
ProductSpecification
Main SPEC
WirelessTechnology
• IEEE802.11b/g/n/ax2.4GHz1024QAMwith1200Mbpps
• IEEE802.11a/n/ac/ax5GHz1024QAMwith2400Mbps
• SupportMU‐MIMO/OFDMAat2.4GHzand5GHz
ExternalInterface
• 1x2.5GELAN(802.3atPOE)
• 1xresetbutton
• 1xMicroUSBConsolePort(UART)
• 1xUSB
LED • 1xtri‐colorLED
PCBDimension • 210*188*1.6mm/6L
EnclosureDimension• 225*225*43mm
Powersupply POE802.3atPD
OperatingTemperature0℃～＋40℃/10～90％RH
Key parts
CPU QualcommIPQ8072A
Wi‐Fi2.4GHzRF QualcommQCN5024
Wi‐Fi5GHzRF QualcommQCN5054
SPINORFlash 8MB
NANDFlash 512MB
RAM DDR4 1GB
512MBDDR4*2
Wi‐FiRFPA/FEM 2.4GHzFEM:QPF4288A(BoarddatauseQPF4228forlowerpower)
5GHz FEM:QPF4588A(BoarddatauseQPF4528forlowerpower)
antenna 4xDualband
PDIC MP8009
Ethernet QCA8081
Console ProlificPL2303G4ZJG8P2
TPM InfineonSLB9670VQ2.0
Internalconnector M.2Connector
Housing design & dimension:
LED definition
Description(ForAlpha/Beta/Charlie/Delta) LED
APisofforrebootstarted Off
NormalOperation SolidGreen
APisbooting&connectingtowirelesscontroller Flashing
Green
Error,nowirelesscontrollerfound.APwill
reboot(ifnotyetclaimedbyacontroller).Check
networkconnectioniferrorpersists.
Ifresetbuttonpressed:APpreparingconfigurationrese
SolidRed
Configurationresetinprogress* FlashingSlowRed
Firmwareupdateinprogress*
Note:Donotdisconnectfrompower FlashingFastRed
APhasnoconnectiontothewirelesscontroller SolidAmber
APisnotclaimedbywirelesscontroller FlashingAmber
Safety Instructions
You can operate the access point (AP) safely if you follow the information in these Safety Instructions
and on the appliance.
Do not reach into the appliance. There are dangerous circuits inside the appliance that can cause death if
you touch them.
Damaged appliances must be returned. It is forbidden to open the hardware appliance or to change its
components. Failure to comply with this rule results in the loss of warranty cover from EDIMAX.
Connect the device to a power socket with a fully functional earth conductor. Defective earth conductor
connections do not comply with the requirements for safety and electromagnetic compatibility. Check
the power socket before connecting the hardware appliance.
The socket-outlet shall be installed near the equipment and shall be easily accessible.
Before you switch on the appliance make sure that your mains voltage complies with the supply voltage
of the appliance. The connection data are shown on the name plate.
To disconnect the appliance completely take the power cable from the power socket. Make sure that the
power plug is freely accessible.
Make sure that no one can trip over the power cable and that it cannot be damaged by objects.
Only connect system peripherals complying with the requirements for protective extra-low voltage
according to EN/IEC 62368-1.
Only use parts and accessories validated by EDIMAX. Using non-approved parts and accessories may
affect the functioning of the appliance and your safety.
The appliance produces heat. Ensure that there is sufficient air circulation to remove the heat.
Avoid a permanent high level of air humidity and formation of condensation. Protect the appliance from
humidity and chemicals. Safe use of the appliance is no longer possible if: the chassis is damaged water
penetrated the appliance objects entered the appliance via air opening smoke comes out of the appliance
the power cable is damaged it does not work properly
Immediately turn off the appliance in the event of one of the above problems, remove the power cable
from the power socket and contact your customer service as soon as possible.
We expressly exclude any product liability and warranty claims if the appliance is not operated
according to the instructions in these notes and to the notes attached to the appliance itself.
PoE-Injector Safety Information
Caution: The PoE injector is to be connected only to PoE networks without routing to the outside plant.
ÌAC Power Cord: The power cord must have regulatory agency approval for the specific country in
which it is used (for example, UL, CSA, VDE, GS, etc.).
The power cord must be a three-conductor type (two current carrying conductors; one ground conductor
terminated on one end by an IEC 60320 appliance coupler (for connection to the PoE-Injector), and on
the other end by a plug containing a ground (earthing) contact).
The power cord must be razed for a minimum of 250 VAC RMS operation, with a minimum rated
current capacity of 5 A (or a minimum wire gauge of 18 AWG (0.75 mm2)).
A PoE-Injector installed in Australia requires power cords with a minimum wire gauge of 16 AWG (1.0
mm2).
The PoE-Injector "Data In" and "Data & Power Out" ports are shielded RJ45 data sockets. They cannot
be used as Plain Old Telephone Service (POTS) telephone sockets. Connect RJ45 data connectors only
to those sockets.
The AC wall socket-outlet must be near the PoE-Injector and easily accessible. You can remove AC
power from the PoE-Injector by disconnecting the AC power cord from either the wall socket-outlet or
the PoE-Injector appliance coupler.
The PoE-Injector "Data In" and "Data & Power Out" interfaces are qualified as Safety Extra-Low
Voltage (SELV) circuits according to IEC 62368-1. Connect these interfaces only to SELV interfaces on
other equipment.
Warnings
Connect the PoE-Injector only to the IP device with which it was bought. Using the PoE-Injector with other
IP devices can cause damage to the IP device.
Read the installation instructions before connecting the PoE-Injector to its power source.
Follow basic electricity safety measures whenever connecting the PoE-Injector to its power source.
A voltage mismatch can cause equipment damage and may pose a fire hazard. If the voltage indicated on the
label is different from the power outlet voltage, do not connect the PoE-Injector to that power outlet.
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC
Rules.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 49cm
between the radiator & your body.
Note: The country code selection is for non-US model only and is not available to all US model.
Per FCC regulation, all WiFi product marketed in US must fixed to US operation channels only.
FCC regulations restrict the operation of this device to indoor use only.
1
Industry Canada statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science
and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following
two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired
operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR
d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en compromettre le fonctionnement.
Operation shall be limited to indoor use only;
leur utilisation doit être limitée à l’intérieur seulement
Radiation Exposure Statement
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with greater than 30cm between the radiator & your body.
Déclaration d'exposition aux radiations
Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour un environnement
non contrôlé. Cet équipement doit être installé et utilisé à plus de 30cm entre le radiateur et votre corps.
RED Compliance Statement
Compliance with 2014/53/EU Radio Equipment Directive (RED)
In accordance with Article 10.8(a) and 10.8(b) of the RED, the following table provides information on the frequency
bands used and the maximum RF transmit power of the product for sale in the EU:
Frequency Range (MHz) Max. Transmit Power (dBm)
EIRP
2412 ~ 2472 19.96 dBm
5180 ~ 5240 22.95 dBm
2
5250 ~ 5320 22.93 dBm
5500 ~ 5700 29.99 dBm
This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
AT BE BG HR CY CZ DK
EE FI FR DE EL HU IE
IT LV LT LU MT NL PL
PT RO SK SI ES SE UK(NI)
This device is restricted to indoor use
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
