Lumination LRXD Series Disk Downlight Guide d'installation

Taper
Guide d'installation
LED.com
© 2023 Current Lighting Solutions, LLC. All rights reserved. Information and specifications subject to change
without notice. All values are design or typical values when measured under laboratory conditions.
Page 1 of 4
(Rev 06/08/23)
IND585-Lumination-LRXD-New-Construction-Frame-Install-Guide
Installation Guide/Manuel d’installation
IND585| A-1028965
Lumination® LRXD
(LRXD Series)
New Construction Frame
BEFORE YOU BEGIN/ AVANT DE COMMENCER
Read these instructions completely and carefully./ Lisez attentivement toutes ces instructions.
WARNING/AVERTISSEMENT
NOTICE
RISK OF ELECTRICAL SHOCK. Turn power o before inspection, installation or removal. Properly ground electrical enclosure.
RISQUES D’INCENDIE OU DE DÉCHARGES ÉLECTRIQUES. Coupez l’alimentation avant d’’inspecter, installer ou déplacer le luminaire. Assurez-vous de
correctement mettre à la terre le boîtier d’alimentation électrique.
RISK OF FIRE. Follow all NEC and local codes. Use only UL approved wire for input/output connections.
RISQUES D’INCENDIE. Respectez tous les codes NEC et codes locaux. N’utilisez que des ls approuvés par UL pour les entrées/sorties de connexion.
Lamp Housings LRXDR4, LRXDR6, LRXDS4, LRXDS6 may be assembled with part FRAMExR/FRAMExS. When Lamp Housings LRXDR4, LRXDR6, LRXDS4, LRXDS6
is assembled with Part FRAMExR/FRAMExS, the nal assembly complies with UL1598 category IFAO recessed luminaire requirements.
LRXD products are suitable for wet location covered ceiling only.
Les boîtiers de lampes LRXDR4, LRXDR6, LRXDS4, LRXDS6 peuvent être montés avec la pièce FRAMExR/FRAMExS. Lorsque les boîtiers des lampes LRXDR4,
LRXDR6, RXDS4, LRXDS6 sont montés avec la pièce FRAMExR/FRAMExS, le montage nal respecte les exigences des luminaires encastrés de la catégorie IFAO
de la norme UL 1598. LRXD produits conviennent pour emplacement humide couverte au plafond uniquement.
Save These Instructions
Use only in the manner intended by the manufacturer.
If you have any questions, contact the manufacturer.
Prepare Electrical Wiring
Electrical Requirements
The LED luminaire must be connected to the mains supply
according to its ratings on the product label.
Grounding Instructions
The grounding and bonding of the overall system shall be
done in accordance with National Electric Code (NEC) and
local codes.
LED.com
© 2023 Current Lighting Solutions, LLC. All rights reserved. Information and specifications subject to change
without notice. All values are design or typical values when measured under laboratory conditions.
Page 2 of 4
(Rev 06/08/23)
IND585-Lumination-LRXD-New-Construction-Frame-Install-Guide
Lumination® (LRXD - Series) Installation Guide/Manuel d’installation
Components
Frame Installation
Alternative
L-brackets
Mounting brackets
1
2 3 4 5
Adjust height and
tighten wing nut
Bars Conduit
B A
34 5
2
Mounting bracket also
could be xed on the short
side of frame
Option A:
If no holes are present on
the short side, use #8-1/2”
self-drilling screws.
Option B:
If the short side has holes,
please use the screws
provided with the frame.
2
Provided Item Qty.
1 Frame (4-inch, 6-inch) 1
2 Mounting brackets 2
3 L-Bracket 2
4 U-Bracket (used only with RC/LRC Series Installs) 1
5 Wing nut 3
Fixture Recommended Frame
LRXDR4 FRAME4R
LRXDS4 FRAME4S
LRXDR6 FRAME6R
LRXDS6 FRAME6S
Fixture
Diameter
Ceiling Hole
Diameter
LRXDR4 4.25–4.9 in.
LRXDR6 5.94–6.79 in.
LRXDS4 4.64–5.35 in.
LRXDS6 6.06–7.32 in.
Note: Part 4 are only for RC/LRC product, Part 5 are only for LRX product.
1
Cut the appropriate size hole into ceiling tile.
Ensure frame hole diameter matches xture
diameter.
Slide hanger bars through adjustable
mounting brackets.
Adjust xture height to be ush with
ceiling and tighten both mounting bracket
wing nuts.
Option A: Mount xture by attaching hanger
bars to T-Grid ceiling (BH3 SKU 94890).
Option B: Mount xture with ½” EMT
conduit. Note: Supplied by 3rd party.
Place side L-brackets on existing frame screws and
tighten with screwdriver on both sides of the frame.
Then attach mounting brackets to both L-brackets with
wing nuts (provided).
LED.com
© 2023 Current Lighting Solutions, LLC. All rights reserved. Information and specifications subject to change
without notice. All values are design or typical values when measured under laboratory conditions.
Page 3 of 4
(Rev 06/08/23)
IND585-Lumination-LRXD-New-Construction-Frame-Install-Guide
Lumination® (LRXD - Series) Installation Guide/Manuel d’installation
Secure provided junction box to the building
structure or existing frame per local codes.
If necessary, remove existing junction box.
Connect AC conduit to provided junction box
and connect the black, white, and green/yellow
wires of the AC leads to the black, white, and
green wires using listed wire
connectors and close junction box.
Optional dimmer: When connecting with
dimming controller, wires must be run through
another separate knockout hole. Connect the
violet (dimming +) and pink (dimming -) wires
to the violet and pink wires of the xture.
Note: Please cover dimming leads with wire
nuts if you won’t connect with dimming leads.
Dimming compatibility for 0-10V, please refer
to Current’s website: www.LED.com
Pink
0-10V +
Violet
L
Dimming +
N
Ground
Black
Violet
White
Pink
Green/Yellow
Lift cover
up as a tool
6
CCT Setting Switch
Springs up
7
CAUTION/ATTENTION
RISK OF PERSONAL INJURY. Operators shall ensure no appendages are in the path of the torsion springs as they are a pinch hazard when released. The springs
will release when the arm is exed downward. Be cautious that no body part is in the path of the spring when released.
RISQUE DE BLESSURE CORPORELLE. Les techniciens veilleront à ce qu’aucun appendice ne se trouve sur le chemin des ressorts de torsion, car ils présentent un
risque de pincement lorsqu’ils sont libérés. Les ressorts seront libérés au moment de échir le bras vers le bas. Faites attention à ce qu’aucune partie du corps ne se
trouve sur le chemin du ressort à sa libération.
Note: For 2700/3000/3500K model and 3500/4000/5000K model, the default CCTs is 3000K
and 3500K respectively. Lift up the cover for the switch, and use it as a tool to choose the
desired CCT.
Load springs into upright position by
twisting the springs upward and carefully
insert the xture to the hole of the frame.
Verify the trim is ush with ceiling.
Lumination® (LRXD - Series) Installation Guide/Manuel d’installation
LED.com
© 2023 Current Lighting Solutions, LLC. All rights reserved. Information and specifications subject to change
without notice. All values are design or typical values when measured under laboratory conditions.
Page 4 of 4
(Rev 06/08/23)
IND585-Lumination-LRXD-New-Construction-Frame-Install-Guide
FCC Statements /Déclarations FCC:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation. This Class [A] RFLD complies with the Canadian standard ICES-005. Ce DEFR de la
classe [A] est conforme à la NMB-005 du Canada.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequen-
cy energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Cet appareil est en conformité avec la section 15 des règlements de la FCC. Sa mise en service est sujette aux deux conditions suivantes : (1) Cet appareil ne peut pas causer des
interférences nuisibles, et (2) cet appareil doit accepter toute interférence reçue, y compris les interférences qui pourraient causer un fonctionnement inadéquat. Cette classe [A]
RFLD est en conformité avec la norme Canadienne ICES-005. Ce DEFR de la classe [A] est conforme à la NMB-005 du Canada.
Remarque: Cet équipement a été testé et prouvé être en conformité avec les limites d’un appareil digital de Classe A, suivant la Section 15 des règlements de la FCC. Ces limites
sont établies pour assurer une protection raisonnable contre les interférences nuisibles lorsque l’équipement est mis en service dans un environnement commercial. Cet équipe-
ment émet, utilise et peut radier une énergie de radio fréquence et, s’il n’est pas installé et utilisé suivant les instructions du manuel, pourrait causer des interférences nuisibles aux
communications radio. Lopération de cet équipement dans une zone résidentielle va probablement causer des interférences nuisibles auquel cas l’utilisateur a l’obligation de corri-
ger le problème à ses propres frais.
These instructions do not purport to cover all details or variations in equipment nor to provide for every possible contingency to be met in connection with installation, operation
or maintenance. Should further information be desired or should particular problems arise which are not covered suciently for the purchaser’s purposes, the matter should be
referred to Current.
Ces instructions ne prétendent pas couvrir tous les détails ou variantes de l’équipement ni couvrir toutes les conditions possibles à satisfaire en rapport avec l’installation,
l’opération ou l’entretien. Si des informations supplémentaires sont souhaitées sur des aspects qui ne sont pas susamment couverts pour satisfaire les besoins du client, ou si
des problèmes particuliers se présentent, veuillez addresser ces questions à Current.
Questions:
Web: LED.com | Phone/Tél: 1-866-855-8629
All product and company names are trademarks™ or registered® trademarks of their respective holders. Use of them does not imply any afliation with or endorsement by
them. All specications are subject to change without notice.
Tous les noms de compagnies et de produits sont des marques déposées™ ou marques enregistrées® de leurs propriétaires respectifs. Leur utilisation ne représente aucune
afliation ni aval de leur part. Toutes les spécications sont sujettes à changement sans préavis.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Lumination LRXD Series Disk Downlight Guide d'installation

Taper
Guide d'installation