STIHL MS 241 C-M Manuel utilisateur

Marque: STIHL

Modèle: MS 241 C-M

Catégorie: Tronçonneuses électriques

Taper: Manuel utilisateur

{

STIHL MS 241 C-M

Instruction Manual

Notice d’emploi

G Instruction Manual

1 - 51

F Notice d’emploi

52 - 107

Original Instruction ManualPrinted on chlorine-free paper

Printing inks contain vegetable oils, paper can be recycled.

0458-738-8221-A. VA1.C14.

0000006537_002_GB

MS 241 C-M

English

{

with electronic systems.

Contents

Dear Customer,

Thank you for choosing a quality

engineered STIHL product.

It has been built using modern

production techniques and

comprehensive quality assurance.

Every effort has been made to ensure

your satisfaction and troublefree use of

the product.

Please contact your dealer or our sales

company if you have any queries

concerning this product.

Your

Dr. Nikolas Stihl

Guide to Using this Manual 2

Safety Precautions 3

Reactive Forces 8

Working Techniques 9

Cutting Attachment 18

Mounting the Bar and Chain 18

Tensioning the Chain 19

Checking Chain Tension 20

Fuel 20

Fueling 21

Chain Lubricant 23

Filling Chain Oil Tank 23

Checking Chain Lubrication 24

Chain Brake 24

Winter Operation 25

Starting / Stopping the Engine 26

Operating Instructions 29

Oil Quantity Control 30

Taking Care of the Guide Bar 30

Shroud 31

Cleaning the Air Filter 31

Engine Management 32

M-Tronic 32

Spark Arresting Screen in Muffler 32

Spark Plug 33

Rewind Starter 34

Storing the Machine 34

Checking and Replacing the Chain

Sprocket 34

Maintaining and Sharpening the

Saw Chain 35

Maintenance and Care 39

Main Parts 41

Specifications 43

Special Accessories 44

Ordering Spare Parts 44

Maintenance and Repairs 44

Disposal 45

Important Safety Instructions 45

Key to Symbols 47

STIHL Limited Emission Control

Warranty Statement 48

CSA Standard 50

MS 241 C-M

English

This Instruction Manual refers to a

STIHL chain saw, also called a machine

in this Instruction Manual.

Pictograms

Pictograms that appear on the machine

are explained in this Instruction Manual.

Depending on the machine and

equipment version, the following

pictograms may appear on the machine.

Symbols in text

WARNING

Warning where there is a risk of an

accident or personal injury or serious

damage to property.

NOTICE

Caution where there is a risk of

damaging the machine or its individual

components.

Engineering improvements

STIHL's philosophy is to continually

improve all of its products. For this

reason we may modify the design,

engineering and appearance of our

products periodically.

Therefore, some changes, modifications

and improvements may not be covered

in this manual.

Guide to Using this Manual

Fuel tank; fuel mixture of

gasoline and engine oil

Tank for chain oil; chain

oil

Engage and release

chain brake

Coasting brake

Direction of chain travel

Ematic; chain oil flow

adjustment

Tension saw chain

Intake air baffle: winter

operation

Intake air baffle: summer

operation

Handle heating

Actuate decompression

valve

Actuate manual fuel

pump

MS 241 C-M

English

General compliance

Comply with national safety regulations

issued, e. g. by employers' liability

insurance associations, social security

institutions, occupational safety and

health authorities or other organisations.

The use of noise emitting machines may

be restricted to certain times by national

or local regulations.

If you have not used this machine

before: Have your dealer or other

experienced user show you how to

operate your machine – or attend a

special course in its operation.

Minors should never be allowed to use

the machine – except for young trainees

over the age of 16 when working under

supervision.

Children, animals and bystanders must

remain at a distance.

The user is responsible for avoiding

injury to third parties or damage to their

property.

Only lend or rent your machine to other

persons with the Instruction Manual and

only to people who are fully familiar with

its use.

The machine may only be operated by

people who are rested, in good physical

condition and mental health. If you have

any condition that might be aggravated

by strenuous work, check with your

doctor before operating a chain saw.

Anyone who has consumed alcohol,

medicines affecting their ability to react

or drugs must not operate the machine.

Postpone the work if the weather is bad

(rain, snow, ice, wind) - higher risk of

accidents!

If you have a pacemaker: The ignition

system of this machine produces an

electromagnetic field of very low

intensity. An effect on individual

pacemaker types cannot be excluded

entirely. STIHL recommends that you

consult your doctor and the

manufacturer of your pacemaker in

order to avoid health hazards.

Intended use

The machine may only be used to saw

wood and wooden objects.

Do not the machine for any other

purpose – risk of accidents!

Do not modify the machine in any way –

this may increase the risk of personal

injury. STIHL excludes all liability for

personal injury and damage to property

caused while using unauthorised

attachments.

Clothing and equipment

Wear proper protective clothing and

equipment.

Avoid clothing that could get caught on

branches, brush or moving parts of the

machine. Do not wear a scarf, necktie or

jewellery. Tie up and confine long hair

(headscarf, cap, hard hat, etc.).

Safety Precautions

Special safety precau-

tions must be observed

when using a chain saw

because the chain runs at

very high speeds and the

cutters are extremely

sharp.

It is important you read

and understand the

Instruction Manual before

first use and keep the

manual in a safe place for

future reference. Non-

observance of the

Instruction Manual may

result in serious or even

fatal injury.

Clothing must be sturdy

and snug-fitting, but allow

complete freedom of

movement. Wear snug

fitting clothing with cut-

retardant pads – no

loose-fitting jacket.

Wear suitable safety

shoes – with cut-retard-

ant material, non-slip

soles and steel toe caps.

Wear a hard hat – if

objects could fall on you.

Wear safety glasses or a

face shield and "per-

sonal" hearing protection

– e. g., ear defenders.

MS 241 C-M

English

STIHL can supply a comprehensive

range of personal protective clothing

and equipment.

Transport

Before any transport – even over short

distances – switch off the machine,

engage the chain brake and attach the

chain scabbard. This avoids the risk of

the saw chain starting unintentionally.

Always carry the chain saw by the

handle – with the hot muffler away from

your body, the guide bar must point to

the rear. Avoid touching hot parts of the

machine, especially the surface of the

muffler – risk of burns!

In vehicles: Properly secure the machine

to prevent tipping, damage and chain oil

or fuel spillage.

Cleaning

Clean plastic parts with a cloth. Harsh

detergents can damage the plastic.

Clean the dust and dirt off the machine –

do not use any grease solvents for this

purpose.

Clean the ventilation slots if necessary.

Do not use a high-pressure cleaner to

clean the machine. The hard jet of water

can damage parts of the machine.

Accessories

Only use those tools, guide bars, chains,

chain sprockets, accessories or

technically equivalent components that

have been approved by STIHL for this

machine. If you have any questions in

this respect, consult a servicing dealer.

Use only high quality tools and

accessories. Otherwise, there may be a

risk of accidents and damage to the

machine.

STIHL recommends the use of genuine

STIHL tools, guide bars, chains, chain

sprockets and accessories. They are

specifically designed to match your

model and meet your performance

requirements.

Refuelling

Switch off the engine before refuelling.

Never refuel the machine while the

engine is still hot – the fuel may spill over

– risk of fire!

Open the fuel filler cap carefully so that

any excess pressure is relieved

gradually and fuel does not splash out.

The machine may only be refuelled in a

well ventilated place. Clean the machine

immediately if fuel is spilled. Do not spill

fuel over your clothing – contaminated

clothing must be changed immediately.

The machines can be equipped with the

following filler caps as standard:

Cliplock filler cap (bayonet-type)

This helps reduce the risk of unit

vibrations causing an incorrectly

tightened filler cap to loosen or come off

and spill quantities of fuel.

Before Starting Work

Check that your saw is properly

assembled and in good condition – refer

to appropriate chapters in the instruction

manual.

– Check the fuel system for leaks,

paying special attention to visible

parts such as the tank cap, hose

connections and the manual fuel

pump (on machines so equipped). If

Wear sturdy protective

gloves made of a resist-

ant material (e.g.

leather).

001BA115 KN

Petrol is an extremely

flammable fuel – keep

clear of naked flames and

fire – do not spill any fuel

– no smoking.

Place the cliplock filler

cap (bayonet-type) in

position, turn as far as

stop and fold the cliplock

down.

Look out for leaks! Never

start the engine if fuel has

been spilled or is leaking

– Fatal burns may result!

MS 241 C-M

English

there are any leaks or damage, do

not start the engine – risk of fire.

Have your saw repaired by a

servicing dealer before using it

again.

– Check operation of chain brake,

front hand guard

– Correctly mounted guide bar

– Correctly tensioned chain

– The trigger and trigger lockout must

move freely and spring back to the

idle position when they are

released.

– Master Control lever must move

easily to STOP, 0 or †

– Check that the spark plug boot is

secure – a loose boot may cause

arcing that could ignite combustible

fumes and cause a fire.

– Never attempt to modify the controls

or safety devices in any way.

– Keep the handles dry and clean –

free from oil and dirt – for safe

control of the saw.

– Make sure there is sufficient fuel

and chain oil in the tanks.

To reduce the risk of personal injury, do

not operate your saw if it is damaged or

not properly assembled.

Starting the chain saw

Always work on a level surface. Ensure

a firm and secure footing. Hold the

machine securely – the chain must not

touch any objects or the floor – danger of

injury due to the rotating saw chain.

Your chain saw is a one-person saw. Do

not allow other persons to be in the

working area – not even while starting.

Do not start the chain saw if the chain is

in a cut.

Move at least 3 meters away from the

place where the machine was refuelled

and never start the motor in enclosed

spaces.

Lock the chain with the chain brake

before starting – risk of injury due to

rotating chain!

Do not drop-start the engine – start as

described in the Instruction Manual.

During operation

Ensure you always have a firm and safe

footing. Take special care when the bark

is wet – danger of slipping!

Always hold the chain saw firmly with

both hands: Right hand on the rear

handle – even if you are left-handed. To

ensure reliable control, wrap your

thumbs tightly around the handlebar and

handle.

In the event of impending danger or in

an emergency, switch off the engine

immediately by moving the Master

Control lever / stop switch to STOP, 0 or

†.

Never let the machine run unattended.

Exercise caution with slippery surfaces,

water, snow, ice, steep slopes, uneven

ground or green wood that has just been

stripped of its bark – danger of slipping!

Use caution with tree stumps, roots,

ditches – danger of stumbling!

Do not work alone – keep within calling

distance of others who are trained in

emergency procedures and can provide

help in an emergency. Helpers at the

cutting site must also wear protective

clothing (helmet!) and stand well clear of

the branches being cut.

More care and attention than usual are

required when wearing ear protection,

as warning sounds (shouts, beeps, etc.)

cannot be heard properly.

Take a break in good time to avoid

tiredness or exhaustion – risk of

accidents!

Dust (e. g., sawdust), fumes and smoke

produced while using the machine may

be hazardous to health. If dust is

generated, wear a dust mask.

When the engine is running: Note that

the saw chain continues to rotate for a

short period after you let go of the

throttle trigger – coasting effect.

No smoking when working with or near

the chain saw - risk of fire! Combustible

fuel vapour may escape from the fuel

system.

001BA087 LÄ

MS 241 C-M

English

Examine the saw chain periodically at

short intervals and as soon as you note

any tangible changes:

– Switch off the engine; wait until the

saw chain is stationary

– Check condition and secure fitting

– Check sharpness

Never touch the saw chain when the

engine is running. If the saw chain

becomes jammed by an object, switch

off the engine immediately before

attempting to remove the object – risk of

injury!

Always turn off the engine before leaving

the machine unattended.

To change the saw chain, switch off the

engine. Risk of injury from the motor

starting unintentionally!

Keep easily combustible materials

(e. g., wood chips, bark, dry grass, fuel)

away from hot exhaust gases and hot

mufflers – risk of fire! Mufflers with

catalytic converters can become

especially hot.

Never work without chain lubrication –

monitor the oil level in the oil tank. Stop

work immediately if the oil level in the oil

tank is too low and top up with chain oil

– see also "Topping up with chain oil"

and "Check chain lubrication".

If the machine is subjected to unusually

high loads for which it was not designed

(e. g., heavy impact or a fall), always

check that it is in good condition before

continuing work – see also "Before

starting work".

Check the fuel system for leaks and

make sure the safety devices are

working properly. Never continue using

a machine that is not in perfect working

order. In case of doubt, have the unit

checked by your servicing dealer.

Check for correct idling, so that the saw

chain stops moving when the throttle

trigger is released. Check the idle setting

regularly and correct when possible.

Have the machine repaired by a STIHL

servicing dealer if the saw chain still

continues to move during idling.

Ensure proper ventilation when working

in trenches, hollows or other confined

locations – risk of fatal injury from

breathing toxic fumes!

If you feel sick, have a headache, vision

problems (e. g., your field of vision gets

smaller), hearing problems, dizziness or

inability to concentrate, stop work

immediately. Such symptoms may be

caused by an excessively high

concentration of exhaust emissions –

risk of accident!

After finishing work

Switch off the motor, engage the chain

brake and attach the chain scabbard.

Storage

When the machine is not in use, it

should be stored in such a way that no-

one is endangered. Secure the machine

against unauthorised use.

Store the machine in a safe, dry room.

Vibrations

Prolonged use of the power tool may

result in vibration-induced circulation

problems in the hands (whitefinger

disease).

No general recommendation can be

given for the length of usage because it

depends on several factors.

The period of usage is prolonged by:

– Hand protection (wearing warm

gloves)

– Work breaks

The period of usage is shortened by:

– Any personal tendency to suffer

from poor circulation (symptoms:

frequently cold fingers, tingling

sensations).

– Low outside temperatures.

– The force with which the handles

are held (a tight grip restricts

circulation).

Continual and regular users should

monitor closely the condition of their

hands and fingers. If any of the above

symptoms appear (e.g. tingling

sensation in fingers), seek medical

advice.

The chain saw produces

poisonous exhaust gases

as soon as the engine

starts. These gases may

be colourless and odour-

less and may contain

unburnt hydrocarbons

and benzene. Never work

with the machine indoors

or in poorly ventilated

areas, even if your

machine is equipped with

a catalytic converter.

MS 241 C-M

English

Maintenance and repairs

Always switch off the engine before any

repair, cleaning or maintenance work

and any work on the chain. Risk of injury

if the engine starts inadvertently!

The machine must be serviced regularly.

Do not attempt any maintenance or

repair work not described in the

Instruction Manual. All other work should

be carried out by a servicing dealer.

STIHL recommends that maintenance

and repair work be carried out only by

authorised STIHL dealers. STIHL

dealers receive regular training and are

supplied with technical information.

Use only high-quality spare parts.

Otherwise, there may be a risk of

accidents and damage to the machine. If

you have any questions in this respect,

consult a servicing dealer.

Do not modify the machine in any way –

this may increase the risk of personal

injury –risk of accidents!

To reduce the risk of fire due to ignition

outside the cylinder, move the master

control level to STOP, 0 or † before

turning the engine over on the starter

when the spark plug boot is removed or

the spark plug is unscrewed!

Do not service or store the machine near

a naked flame – risk of fire due to the

fuel!

Check fuel cap regularly for tightness.

Use only spark plugs that are in perfect

condition and have been approved by

STIHL – see "Specifications".

Check ignition lead (insulation in good

condition, secure connection).

Check that the muffler is in perfect

working condition.

Do not use the machine if the muffler is

damaged or missing – risk of fire,

damage to hearing!

Never touch a hot muffler – risk of burns!

The condition of the anti-vibration

elements influences vibration behaviour

– inspect anti-vibration elements

periodically.

Inspect chain catcher – replace if

damaged.

Switch off the engine

– To check the chain tension

– To retension the chain

– To replace the chain

– For remedying malfunctions

Observe sharpening instructions – for

safe and proper handling, always keep

the chain and guide bar in flawless

condition. Keep the chain properly

sharpened, tensioned and well

lubricated.

Change chain, guide bar and chain

sprocket in due time.

Regularly check that the clutch drum is

in perfect working condition.

Always store fuel and chain lubricant

only in the specified type of containers

and ensure they are correctly labelled.

Store in a dry, cool and secure place

protected against light and sunlight.

In the event of a chain brake

malfunction, switch off the machine

immediately – risk of injury! Consult a

servicing dealer – do not use the

machine until the malfunction has been

remedied, see "Chain brake".

Maintenance, replacement, or repair of

the emission control devices and

systems may be performed by any

nonroad engine repair establishment or

individual. However, if you make a

warranty claim for a component which

has not been serviced or maintained

properly or if nonapproved replacement

parts were used, STIHL may deny

coverage.

For any maintenance please refer to the

maintenance chart and to the warranty

statement near the end of the instruction

manual.

MS 241 C-M

English

The most common reactive forces are:

kickback, pushback and pull-in.

Dangers of kickback

Kickback occurs when the saw is

suddenly thrown up and back in an

uncontrolled arc towards the operator.

Kickback occurs if, for example,

– The saw chain in the area of the

upper quarter of the guide bar nose

unintentionally comes into contact

with wood or a solid object – e. g.,

unintentionally touches another limb

during limbing

– The saw chain at the nose of the

guide bar is briefly pinched in the cut

QuickStop chain brake:

This device reduces the risk of injury in

certain situations – it cannot prevent

kickback. If activated, the brake stops

the saw chain within a fraction of a

second –

refer to chapter "Chain brake" in this

Instruction Manual.

Reducing the risk of kickback

– Work cautiously and methodically

– Hold the chain saw firmly with both

hands and maintain a secure grip

– Always cut at full throttle

– Be aware of the location of the guide

bar nose

– Do not cut with the guide bar nose

– Be especially careful with small,

tough limbs, undergrowth and

offshoots – the saw chain may

become caught in them

– Never cut several limbs at once

– Do not lean too far forward

– Do not cut above shoulder height

– Use extreme caution when re-

entering a previous cut

– Do not attempt plunge cuts if you

are not experienced in this cutting

technique

– Be alert for shifting of the log or

other forces that may cause the cut

to close and pinch the chain

– Always cut with a correctly

sharpened, properly tensioned saw

chain – the depth gauge setting

must not be too large

– Use low-kickback saw chains as

well as narrow-radius guide bars

Pull-in (A)

When the chain on the bottom of the bar

– overbucking – is suddenly pinched,

caught or encounters a foreign object in

the wood, the chain saw may suddenly

Reactive Forces

Kickback can result in

fatal cuts.

001BA036 KN

001BA257 KN

001BA037 KN

MS 241 C-M

English

be drawn forward toward the log – to

avoid this, engage the bumper spike

firmly in the wood.

Pushback (B)

When the chain on the top of the bar –

underbucking – is suddenly pinched,

caught or encounters a foreign object in

the wood, the chain saw may suddenly

be driven straight back toward the

operator – to avoid this:

– Do not allow the top of the guide bar

to become jammed

– Do not twist the guide bar in the cut

Be very careful

– With freely hanging limbs

– With trunks that are under tension

between other trees because they

fell unfavourably

– When working in windbreaks

In these cases, do not use a chain saw –

use a hoist, winch or dragline instead.

Pull out trunks that are lying about and

have been cut free. Whenever possible,

deal with them in open areas.

Dead wood (brittle, rotten or dead wood)

poses a significant, highly unpredictable

hazard. It is extremely difficult or even

practically impossible to recognise the

danger. Use aids such as winches or

draglines.

When felling close to roads, rail lines,

power lines, etc., work with particular

care. If necessary, notify police, power

companies or railway authorities.

Sawing and felling work, including all

related work (plunge cutting, limbing,

etc.) may only be carried out by persons

who have been specially trained and

instructed. Persons who are not

experienced chain saw users should not

carry out any such work – increased risk

of accidents!

Country-specific legislation on felling

technique must be complied with during

felling work.

Cutting

Do not operate your saw with the

starting throttle lock engaged. Engine

speed cannot be controlled with the

throttle trigger in this position.

Work calmly and carefully – in daylight

conditions and only when visibility is

good. Ensure you do not endanger

others – stay alert at all times.

First-time users are advised to practice

cutting logs on a sawhorse – see "When

cutting small logs".

Use the shortest possible guide bar: The

chain, guide bar and chain sprocket

must match each other and your saw.

001BA038 KN

Working Techniques

MS 241 C-M

English

Position the saw so that your body is

clear of the cutting attachment.

Always pull the saw out of the cut with

the chain running.

Use your chain saw for cutting only. It is

not designed for prying or shoveling

away limbs, roots or other objects.

Do not underbuck freely hanging limbs.

Take care when cutting scrub and young

trees. The saw chain may catch and

throw thin shoots in your direction.

To reduce the risk of injury, take special

care when cutting shattered wood

because of the risk of injury from slivers

being caught and thrown in your

direction.

Make sure your saw does not touch any

foreign materials: Stones, nails, etc. may

be flung off and damage the saw chain.

The saw may kick back unexpectedly –

risk of accidents.

If the rotating chain makes contact with

a rock or other solid object there is a risk

of sparking which may cause easily

combustible material to catch fire under

certain circumstances. Dry plants and

scrub are also easily combustible,

especially in hot and dry weather

conditions. If there is a risk of fire, do not

use your chainsaw near combustible

materials, dry plants or scrub. Always

contact your local forest authority for

information on a possible fire risk.

If on a slope, stand on the uphill side of

the log. Watch out for rolling logs.

When working at heights:

– Always use a lift bucket

– Never work on a ladder or in a tree

– Never work on an insecure support

– Do not work above shoulder height

– Never operate your power tool with

one hand

Begin cutting with the saw at full throttle

and engage the spiked bumper firmly in

the wood, and then continue cutting.

Never work without the spiked bumper

because the saw may pull you forwards

and off balance. Always engage the

spiked bumper securely in the tree or

limb.

Note when reaching the end of a cut that

the saw is no longer supported in the

kerf. You have to take the full weight of

the machine since it might otherwise go

out of control.

When cutting small logs:

– Use a sturdy and stable support –

sawhorse.

– Never hold the log with your leg or

foot.

– Never allow another person to hold

the log or help in any other way.

Limbing:

– Use a low kickback chain.

– Work with the saw supported

wherever possible.

– Do not stand on the log while

limbing it.

– Do not cut with the bar nose.

– Watch for limbs which are under

tension.

– Never cut several limbs at once.

Lying or standing logs under tension:

Always make cuts in the correct

sequence (first at the compression

side (1), then at the tension side (2), the

saw may otherwise pinch or kick back –

risk of injury.

001BA082 KN

001BA033 KN

MS 241 C-M

English

N Make relieving cut at the

compression side (1)

N Make bucking cut at the tension

side (2)

Be wary of pushback when making

bucking cut from the bottom upwards

(underbuck).

NOTICE

Do not cut a lying log at a point where it

is touching the ground because the saw

chain will otherwise be damaged.

Ripping cut:

Cutting technique in which the spiked

bumper is not used – risk of pull-in – start

the cut with the guide bar at the

shallowest possible angle – take extra

care since there is an increased danger

of kickback.

Preparations for Felling

Check that there are no other persons in

the felling area – other than helpers.

Make sure no-one is endangered by the

falling tree – the noise of your engine

may drown any warning calls.

Maintain a distance of at least 2 1/2 tree

lengths from the next felling site.

Determine direction of fall and escape

path.

Select gap in stand into which you want

the tree to fall.

Pay special attention to the following

points:

– The natural lean of the tree

– Any unusually heavy limb structure,

damage

– The wind direction and speed – do

not fell in high winds

– Sloping ground

– Neighboring trees

– Snow load

– Soundness of tree – take special

care if trunk is damaged or in case

of deadwood (dry, decayed or rotted

wood)

001BA151 KN

001BA152 KN

001BA189 KN

001BA088 LÄ

1 1

MS 241 C-M

English

A Direction of fall

B Escape path (or retreat path)

– Establish paths of escape for

everyone concerned – opposite to

direction of fall at about 45°.

– Remove all obstacles from escape

paths.

– Place all tools and equipment a safe

distance away from the tree, but not

on the escape paths.

– Always keep to the side of the falling

tree and only walk away along the

preplanned escape path.

– On steep slopes, plan escape

routes parallel to the slope.

– When walking away along the

escape path, watch out for falling

limbs and watch the top of the tree.

Preparing work area at base of tree

– First clear the tree base and work

area from interfering limbs and

brush to provide a secure footing.

– Clean lower portion of tree base

(e.g. with an axe) – sand, stones

and other foreign objects will dull the

saw chain.

– Make the vertical cut first, then the

horizontal – but only if the wood is

sound

Felling Notch

Preparing felling notch

The felling notch (C) determines the

direction of fall.

Important:

– Make felling notch at a right angle to

the planned direction of fall.

– Cut close to the ground.

– Cut to a depth of about 1/5 to 1/3 of

the trunk diameter.

001BA040 KN

45°

001BA146 KN

001BA271 KN

MS 241 C-M

English

Determine direction of fall with gunning

sight on shroud and fan housing

Your chainsaw has a gunning sight on

the shroud and fan housing. Use this

gunning sight.

Making Felling Notch

Position the saw so that the felling notch

is at a right angle to the direction you

want the tree to fall.

The sequence in which the felling notch

is made with a horizontal cut (bottom)

and angled cut (top) is defined in

country-specific regulations.

N Make horizontal cut (bottom)

N Make the angled cut (top) at about

45°- 60° to the horizontal cut.

Check direction of fall

N Position the saw in the horizontal

cut. The gunning sight must point in

the planned direction of fall – if

necessary, correct direction of fall

by re-cutting the felling notch.

Sapwood cuts

Sapwood cuts in long-fibered softwood

help prevent sapwood splintering when

the tree falls. Make cuts at both sides of

the trunk at same height as bottom of

felling notch to a depth of about 1/10 of

trunk diameter. On large diameter trees,

cut to no more than width of guide bar.

Do not make sapwood cuts if wood is

diseased.

Basic Information on Felling Cut

Stump dimensions

The felling notch (C) determines the

direction of fall.

The hinge (D) helps control the falling

tree.

– Width of hinge: about 1/10 of tree

diameter.

– To reduce the risk of accidents, do

not cut through the hinge – you

could lose control of the direction of

fall.

– Leave a broader hinge on rotten

trees.

001BA153 KN

001BA150 KN

001BA259 KN

1/10

MS 241 C-M

English

The tree is felled with the felling cut (E).

– Cut horizontally.

– 1/10 (at least 3 cm) of width of

hinge (D) higher than bottom of

felling notch (C).

The holding strap (F) or stabilizing

strap (G) supports the tree and helps

prevent it from falling prematurely.

– Width of strap: about 1/10 to 1/5 of

tree diameter.

– Do not cut into the strap while

making the felling cut.

– Leave a broader strap on rotten

trees.

Plunge cutting

– For relieving cuts during bucking

– For wood carving

N Use a low kickback chain and

exercise particular caution

1. Begin cut by applying the lower

portion of the guide bar nose – do

not use upper portion because of –

risk of kickback. Start cutting at full

throttle until depth of kerf is twice the

width of the guide bar.

2. Swing saw slowly into plunge-

cutting position – take care because

of the risk of kickback or pushback.

3. Make the plunge cut very carefully.

Danger of pushback.

Use the plunge-cutting sight if possible.

The plunge-cutting sight and the top and

bottom of the guide bar are parallel.

When making the plunge cut, the sight

helps keep the hinge horizontal, i.e. the

same thickness all round. To do this,

hold the plunge-cutting sight parallel to

the chord of the felling notch.

Felling wedges

Make use of wedges as soon as

possible, i.e. providing they do not

interfere with cutting. Drive wedge into

felling cut with a suitable tool.

Use only aluminum or plastic wedges –

never steel. Steel wedges can seriously

damage the saw chain and cause

dangerous kickback.

Select felling wedges that suit the

diameter of the tree and width of the kerf

(felling cut (E)).

Contact your STIHL dealer for advice on

selecting the right felling wedge (length,

width and height).

Choosing Right Felling Cut

The criteria for choosing the right felling

cut are the same as those for

determining the direction of fall and the

escape path.

There are many different variations of

these characteristics. Only the two most

common characteristics are described in

this manual:

Felling Cut with Stabilizing Strap

(Normal Tree)

A) Small diameter trees

Perform this felling cut when the tree

diameter is smaller than the length of the

guide bar.

001BA269 KN

001BA270 KN

Left: Normal tree – vertical trunk

with uniform tree crown.

Right: Leaner – tree crown leans in

direction of fall.

001BA260 KN

MS 241 C-M

English

Shout a warning before starting the

felling cut.

N Start felling cut (E) using plunge-cut

method – insert full length of guide

bar in the trunk.

N Engage the spiked bumper behind

the hinge and use it as a pivot –

avoid repositioning the saw more

than necessary.

N Enlarge felling cut as far as

hinge (1).

– Do not cut into the hinge.

N Enlarge felling cut as far as

stabilizing strap (2).

– Do not cut into the stabilizing strap.

N Insert a felling wedge (3).

Shout a second warning immediately

before the tree falls.

N Holding the saw with outstretched

arms, cut through the stabilizing

strap horizontally at the same level

as the felling cut.

B) Large diameter trees

Perform this felling cut when the tree

diameter is greater than the length of the

guide bar.

Shout a warning before starting the

felling cut.

N Engage the spiked bumper at the

required height of the felling cut and

use it as a pivot – avoid

repositioning the saw more than

necessary.

N The guide bar nose enters the

wood (1) before it reaches the hinge

– hold the saw horizontally and

swing it as far as possible.

N Enlarge felling cut as far as

hinge (2).

– Do not cut into the hinge.

N Enlarge felling cut as far as

stabilizing strap (3).

– Do not cut into the stabilizing strap.

Continue the felling cut on the other side

of the trunk.

Make sure the second cut is at the same

height as the first cut.

001BA261 KN

001BA273 KN

001BA263 KN

MS 241 C-M

English

N Start felling cut using plunge-cut

method.

N Enlarge felling cut as far as

hinge (4).

– Do not cut into the hinge.

N Enlarge felling cut as far as

stabilizing strap (5).

– Do not cut into the stabilizing strap.

N Insert a felling wedge (6).

Shout a second warning immediately

before the tree falls.

N Holding the saw with outstretched

arms, cut through the stabilizing

strap horizontally at the same level

as the felling cut.

Felling Cut with Holding Strap (Leaner)

A) Small diameter trees

Perform this felling cut when the tree

diameter is smaller than the length of the

guide bar.

N Plunge the guide bar into the trunk

until it emerges at the other side.

N Enlarge the felling cut (E) in

direction of hinge (1).

– Cut horizontally.

– Do not cut into the hinge.

N Enlarge the felling cut in direction of

holding strap (2).

– Cut horizontally.

– Do not cut into the holding strap.

Shout a second warning immediately

before the tree falls.

N Cut through the holding strap at a

downward angle from outside with

outstretched arms.

001BA274 KN

001BA265 KN

001BA266 KN

MS 241 C-M

English

B) Large diameter trees

Perform this felling cut when the tree

diameter is greater than the length of the

guide bar.

N Engage the spiked bumper behind

the holding strap and use it as a

pivot – avoid repositioning the saw

more than necessary.

N The guide bar nose enters the

wood (1) before it reaches the hinge

– hold the saw horizontally and

swing it as far as possible.

– Do not cut into the holding strap or

hinge.

N Enlarge felling cut as far as

hinge (2).

– Do not cut into the hinge.

N Enlarge felling cut as far as holding

strap (3).

– Do not cut into the holding strap.

Continue the felling cut on the other side

of the trunk.

Make sure the second cut is at the same

height as the first cut.

N Engage the spiked bumper behind

the hinge and use it as a pivot –

avoid repositioning the saw more

than necessary.

N The guide bar nose enters the

wood (4) before it reaches the

holding strap – hold the saw

horizontally and swing it as far as

possible.

N Enlarge felling cut as far as

hinge (5).

– Do not cut into the hinge.

N Enlarge felling cut as far as holding

strap (6).

– Do not cut into the holding strap.

Shout a second warning immediately

before the tree falls.

N Cut through the holding strap at a

downward angle from outside with

outstretched arms.

001BA267 KN

001BA268 KN

MS 241 C-M

English

A cutting attachment consists of the saw

chain, guide bar and chain sprocket.

The cutting attachment that comes

standard is designed to exactly match

the chain saw.

– The pitch (t) of the saw chain (1),

chain sprocket and the nose

sprocket of the Rollomatic guide bar

must match.

– The drive link gauge (2) of the saw

chain (1) must match the groove

width of the guide bar (3).

If non-matching components are used,

the cutting attachment may be damaged

beyond repair after a short period of

operation.

Chain Scabbard

Your saw comes standard with a chain

scabbard that matches the cutting

attachment.

If guide bars of different lengths are

mounted to the saw, always use a chain

scabbard of the correct length which

covers the complete guide bar.

The length of the matching guide bars is

marked on the side of the chain

scabbard.

Removing the chain sprocket cover

N Unscrew the nut and remove the

chain sprocket cover.

N Turn the screw (1)

counterclockwise until the tensioner

slide (2) butts against the left end of

the housing slot.

Cutting Attachment

001BA248 KN

001BA244 KN

Mounting the Bar and Chain

533BA001 KN

001BA185 KN

La page charge ...

STIHL MS 241 C-M Manuel utilisateur

Marque: STIHL

Modèle: MS 241 C-M

Catégorie: Tronçonneuses électriques

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: STIHL MS 241 C-M User manual

STIHL MS 241 C-M Manuel utilisateur

STIHL MS 241 C-M Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents