EarthQuake 39381 Victory Rear Tine Tiller Manuel utilisateur

Marque: EarthQuake

Modèle: 39381 Victory Rear Tine Tiller

Catégorie: Mini motoculteurs

Taper: Manuel utilisateur

Operator Manual

Manuel de l’utilisateur

Victory™

Rear Tine Tiller

Model Number, Numéros de modèle:

39381

P/N: 39393

ECN: 13205

REV 1: 07/13/2021

Get parts or technical assistance online at

www.getearthquake.com or call (800) 345-6007

Pièces détachées et assistance technique en ligne à

www.getearthquake.com ou composer le (800) 345-6007

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.

CE LIVRET D’INSTRUCTIONS CONTIENT DES INFORMATIONS IMPORTANTES SUR LA SÉCURITÉ. VEUILLEZ LE LIRE ET LE CONSERVER POUR TOUTE CONSULTA-

TIONEXTÉRIEURE.

ENGLISHFRANÇAIS

Operator Manual

VICTORY REAR TINE TILLER

Get parts online at www.getearthquake.com or Call 800-345-6007 M-F 8-4:30 CST

INTRODUCTION

Thank you for purchasing your product from Earthquake®. We have worked to ensure that this product meets the highest stan-

dards for usability and durability. With proper care, your purchase will provide many years of service.

Please read this entire manual before installation and use. Earthquake® reserves the right to change, alter or improve the product

and this document at any time without prior notice. Due to continuous product improvements, product images may not be exact.

Some assembly may be required.

Read and keep this manual for future reference. This manual contains important information regarding safety, assembly, operation

and maintenance. The owner must be certain that all the product information is included with the unit. This information includes

the manual, the replacement parts and the warranties. This information must be included to make sure state laws and other laws

are followed. All persons to whom rent/loan this unit must have access to and understand this information. This manual should

remain with the product even if it is resold.

CONTENTS

Introduction/Contents ..................................................................................................................................................................................................................2

Bolt Identication Chart ................................................................................................................................................................................................................3

Warnings and Safety Precautions ..........................................................................................................................................................................................4-8

Features ..............................................................................................................................................................................................................................................9

Assembly ................................................................................................................................................................................................................................... 10-12

Operation .................................................................................................................................................................................................................................. 12-16

Maintenance and Storage ................................................................................................................................................................................................... 16-19

Troubleshooting and Repair ......................................................................................................................................................................................................20

STOP! ACTIVATE YOUR WARRANTY BEFORE USE

All products must be registered within 30 days from the date of purchase in order to be covered under

warranty. For more information regarding Warranty and Registration please review the Warranty and Regis-

tration terms and conditions expressed in the warranty insert.

REGISTRATION AND SERVICE

Record the product model number and serial number in the

space provided for easy reference when ordering parts or

requesting technical support. Excluding emissions-related

warranty items, the warranty is valid only if the completed

registration is received by Ardisam within 30 days of purchase.

You can register your warranty online by visiting

www.GetEarthquake.com, or by mailing it to:

Ardisam, PO Box 666, Cumberland, WI 54829. You may also call

our Customer Service department at (800) 345-6007 Mondays

through Fridays from 8 a.m. to 4:30 p.m. CST.

Serial Number

Location

Operator Manual

VICTORY REAR TINE TILLER

Get parts online at www.getearthquake.com or Call 800-345-6007 M-F 8-4:30 CST

BOLT IDENTIFICATION CHART

Bolts shown are for size reference only. Extra hardware may be

included in the parts bag.

(A)

M10 x 45 MM

Flange Bolt

Qty 4

(F)

M6 x 16 MM Bolt

Qty 6

(D)

M10 X 20 MM Washer

Qty 6

(C)

M10 Nut

Qty 6

(G)

M6 Nut

Qty 6

(E)

M6 X 12 MM Washer

Qty 6

(B)

M10 x 25 MM

Flange Bolt

Qty 2

(H)

M6 X 18.8 MM Washer

Qty 6

(I)

Lock Pin

Qty 1

(K)

Lock Pin

Qty 2

Operator Manual

VICTORY REAR TINE TILLER

Get parts online at www.getearthquake.com or Call 800-345-6007 M-F 8-4:30 CST

NOTICE

NOTICE INDICATES YOUR EQUIPMENT CAN BE DAMAGED

IF THE SAFETY INSTRUCTIONS THAT FOLLOW THIS SIGNAL

WORD ARE NOT OBEYED.

WARNINGS AND SAFETY PRECAUTIONS

OPERATOR RESPONSIBILITY

Accurate assembly and safe and eective use of the machine is

the operator responsibility.

• Read and follow all safety instructions.

• Carefully follow all assembly instructions.

• Maintain the machine according to directions and

schedule included in this Earthquake® operator manual.

• Ensure that anyone who uses the machine is familiar with

all controls and safety precautions.

SPECIAL MESSAGES

Your manual contains special messages to bring attention to

potential safety concerns, machine damage as well as helpful

operating and servicing information. Please read all the

information carefully to avoid injury and machine damage.

NOTE: General information is given throughout the manual

that may help the operator in the operation or service of the

machine.

This symbol points out important safety instructions

which if not followed could endanger your personal

safety. Read and follow all instructions in this manual

before attempting to operate this equipment.

BEFORE OPERATING EQUIPMENT:

Please read this section carefully. Read entire operating and

maintenance instructions for this product. Failure to follow

instructions could result in serious injury or death. Operate the

machine according to the safety instructions outlined here and

inserted throughout the text. Anyone who uses this machine

must read the instructions and be familiar with the controls.

INTENDED USE / FORESEEABLE MISUSE

IMPORTANT: This is a motorized rotary tiller that works the soil

by means of rotating tines. It is pedestrian-controlled, with a

gasoline-fueled internal combustion engine to power the tines.

It shall not be used for any other purpose.

CAUTION

CAUTION INDICATES A HAZARD WHICH, IF NOT AVOIDED,

COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY

DAMAGE.

WARNING

WARNING INDICATES A HAZARD WHICH, IF NOT AVOIDED,

COULD RESULT IN DEATH OR SERIOUS INJURY AND/OR

PROPERTY DAMAGE.

DANGER

DANGER INDICATES A HAZARD WHICH, IF NOT AVOIDED,

CERTAINLY WILL RESULT IN DEATH OR SERIOUS INJURY

AND/OR PROPERTY DAMAGE.

IMPORTANT

IMPORTANT INDICATES HELPFUL INFORMATION FOR

PROPER ASSEMBLY, OPERATION OR MAINTENANCE OF

YOUR EQUIPMENT.

WARNING

YOU MUST READ, UNDERSTAND AND COMPLY WITH ALL

SAFETY AND OPERATING INSTRUCTIONS IN THIS MANUAL

BEFORE ATTEMPTING TO SETUP AND OPERATE YOUR

MACHINE.

FAILURE TO COMPLY WITH ALL SAFETY AND OPERATING

INSTRUCTIONS CAN RESULT IN LOSS OF MACHINE

CONTROL, SERIOUS PERSONAL INJURY TO YOU AND/OR

BYSTANDERS, AND RISK OF EQUIPMENT AND PROPERTY

DAMAGE. THE TRIANGLE IN THE TEXT SIGNIFIES

IMPORTANT CAUTIONS OR WARNINGS WHICH MUST BE

FOLLOWED.

DANGER

SRT CRT

Keep away from rotating tines.

Rotating tines will cause injury.

Operator Manual

VICTORY REAR TINE TILLER

Get parts online at www.getearthquake.com or Call 800-345-6007 M-F 8-4:30 CST

GENERAL SAFETY RULES

• Read, understand, and follow all instructions on the

machine and in the manual(s). Be thoroughly familiar with

the controls and the proper use of the machine before

starting. Know how to stop the machine and disengage

the controls quickly.

• Use this equipment for its intended purpose only.

• Familiarize yourself with all of the safety and operating

decals on this equipment and on any of its attachments

or accessories.

• Do not put hands or feet near or under rotating parts.

• Only allow responsible individuals who are familiar with

the instructions to operate the machine. Never allow

children to operate this machine. Never allow adults to

operate the machine without proper instruction.

• Thoroughly inspect the area where the machine is to be

used and remove all foreign objects. Your equipment can

propel small objects at high speed causing personal injury

or property damage. Stay away from breakable objects,

such as house windows, automobiles, greenhouses, etc.

• Keep the area of operation clear of all persons, particularly

small children and pets.

• Do not operate in shorts or open toed shoes. Wear proper

Personal Protective Equipment (PPE) at all times, such as

gloves, proper footwear, and eye protection.

• Do not wear loose clothing or jewelry. They can get caught

in moving parts. Always keep hands, feet, hair and loose

clothing away from any moving parts on engine and

machine.

• Always wear safety goggles or safety glasses with side

shields when operating the machine to protect your eyes

from foreign objects which can be thrown from the unit.

Always wear a protective hearing device.

• Always wear work gloves and sturdy footwear. Wear

footwear that will improve footing on slippery surfaces.

Leather work shoes or short boots work well for most

people. These will protect the operator’s ankles and shins

from small sticks, splinters, and other debris.

• It is advisable to wear protective headgear to prevent

the possibility of being struck by small ying particles,

or being struck by low hanging branches, twigs, or other

objects which may be unnoticed by the operator.

• Do not operate product when fatigued or under the

inuence of alcohol, drugs or other medication which

can cause drowsiness or aect your ability to operate this

machine safely.

• Never operate machine in wet grass. Always be sure of

your footing; keep a rm hold on the handle and walk;

never run.

• Watch for trac when operating machine near, or when

crossing roads.

• Temperature of muer and nearby areas may exceed

150° F (65° C). Allow muer and engine areas to cool

before touching. Never pick up or carry the machine while

the engine is running.

• Prolonged exposure to noise and vibration from gasoline

engine-powered equipment should be avoided. Take

intermittent breaks and/or wear ear protection from engine

noise as well as heavy work gloves to reduce vibration in the

hands.

• When moving the packaged machine, always do so with a

partner.

• Check local regulations for age restrictions on use of this

machine.

• Never attempt to make any adjustment while the

engine (motor) is running (except where specically

recommended by the manufacturer).

• The tines of the tiller should not rotate when the drive

control lever is released into the neutral position. If it does

rotate when in neutral, contact Earthquake® Customer

Service for instruction.

ENGINE SAFETY PRECAUTIONS

If your product comes with a separate engine manual, be sure

to read and follow all safety and warning precautions outlined

there, in addition to any in this manual.

PREVENTING CARBON MONOXIDE POISONING

• Always start and run engine outdoors. Do not start or run

engine in an enclosed area, even if doors or windows are

open.

• Never try to ventilate engine exhaust indoors. Carbon

monoxide can reach dangerous levels very quickly.

• Never run engine outdoors where exhaust fumes may be

pulled into a building.

Operator Manual

VICTORY REAR TINE TILLER

Get parts online at www.getearthquake.com or Call 800-345-6007 M-F 8-4:30 CST

• Never run engine outdoors in a poorly ventilated area

where the exhaust fumes may be trapped and not easily

taken away. (Examples include: in a large hole or areas

where hills surround your working area.)

• Never run engine in an enclosed or partially enclosed area.

(Examples include: buildings that are enclosed on one or

more sides, under tents, car ports or basements.)

• Always run the engine with the exhaust and muer

pointed in the direction away from the operator.

• Never point the exhaust muer towards anyone. People

should always be many feet away from the operation of

the engine and its attachments.

• Do not change the engine governor settings or over-

speed the engine.

PREPARATION

• Dress appropriately when operating the tiller. Always

wear sturdy footwear. Never wear sandals, sneakers or

open-toed shoes, and never operate the tiller with bare

feet. Do not wear loose clothing that might get caught in

moving parts. Wear proper Personal Protective Equipment

(PPE) at all times, such as gloves, proper footwear, and eye

protection.

WARNING

ENGINES GIVE OFF CARBON MONOXIDE, AN ODORLESS,

COLORLESS, POISONOUS GAS. CARBON MONOXIDE MAY

BE PRESENT EVEN IF YOU DO NOT SMELL OR SEE ANY

ENGINE EXHAUST. BREATHING CARBON MONOXIDE CAN

CAUSE NAUSEA, FAINTING OR DEATH, IN ADDITION TO

DROWSINESS, DIZZINESS AND CONFUSION.

IF YOU EXPERIENCE ANY OF THESE SYMPTOMS, SEEK

FRESH AIR AND MEDICAL ATTENTION IMMEDIATELY.

HOT GASES ARE A NORMAL BY-PRODUCT OF A

FUNCTIONING INTERNAL COMBUSTION ENGINE. FOLLOW

ALL SAFETY INSTRUCTIONS TO PREVENT BURNS AND

FIRES.

DO NOT ALTER/MODIFY ENGINE:

• NEVER ALTER OR MODIFY THE ENGINE FROM THE

FACTORY. SERIOUS INJURY OR DEATH MAY OCCUR IF

ENGINE IS MODIFIED OR ALTERED.

• WHEN WORKING ON OR REPLACING PARTS FOR THE

ENGINE OR PRODUCT, YOU MUST ALWAYS PUT THE ON/

OFF SWITCH TO THE OFF POSITION.

• Carefully inspect the area to be tilled and remove all

foreign objects. Do not till above underground water lines,

gas lines, electric cables, or pipes. Do not operate the

tiller in soil with large rocks and foreign objects which can

damage the equipment.

• Disengage all clutches and leave control lever in the

neutral position before starting the engine (motor).

SAFE HANDLING OF GASOLINE

Use extra care in handling gasoline and other fuels. They are

extremely ammable and vapors are explosive.

• Extinguish all cigarettes, cigars, pipes and other sources of

ignition.

• Never remove gas cap or add fuel with the engine

running.

• Allow engine to cool before refueling.

• Never store the machine or fuel container where there

is an open ame, spark, or pilot light such as on a water

heater or on other appliances.

• Never ll containers inside a vehicle or on a truck or trailer

bed with a plastic liner. Always place containers on the

ground away from your vehicle before lling.

• Remove gas powered equipment from the truck or trailer

and refuel it on the ground. If this is not possible, then

refuel such equipment with a portable container, rather

than from a gasoline dispenser nozzle.

• Keep the nozzle in contact with the rim of the fuel tank or

container opening at all times until fueling is complete. Do

not use a nozzle lock open device.

• If fuel is spilled on clothing, change clothing immediately.

• Never overll fuel tank. Replace gas cap and tighten

securely.

• If fuel is spilled do not attempt to start the engine but

move the machine away from the area of spillage and

avoid creating any source of ignition until fuel vapors have

dissipated.

• Prevent re and explosion caused by static electric

discharge. Use only nonmetal, portable fuel containers

approved by the Underwriter’s Laboratory (UL) or the

American Society for Testing & Materials (ASTM).

• Always ll fuel tank outside in a well ventilated area. Never

ll your fuel tank with fuel indoors. (Examples include:

basement, garage, barn, shed, house, porch, etc.).

Operator Manual

VICTORY REAR TINE TILLER

Get parts online at www.getearthquake.com or Call 800-345-6007 M-F 8-4:30 CST

• Test the fuel cap for proper installation before starting and

using engine.

• Always run the engine with fuel cap properly installed on

the engine.

NOTICE

THE RIGHT AND LEFT SIDES OF YOUR

ROTOTILLER ARE DETERMINED FROM

THE OPERATING POSITION AS YOU

FACE THE DIRECTION OF FORWARD

TRAVEL.

ENGINE IS SHIPPED FROM FACTORY

WITHOUT OIL. YOU MUST ADD ENGINE

OIL BEFORE STARTING ENGINE.

OPERATION

• Do not allow hands, feet, or other body parts, or clothing

near the rotating tines or any other moving part. The tines

begin to rotate once the engine/motor is started and the

activating device is engaged. The tines may momentarily

rotate after the activating device is released.

• Exercise extreme caution when crossing gravel surfaces.

Stay alert for hidden hazards or trac.

• If an object becomes lodged in the tines, ip the ON/

OFF switch to the OFF position, allow to cool before

attempting to remove the foreign object.

• After striking a foreign object, stop the engine (motor),

remove the wire from the spark plug (or disconnect

the cord for electric products), thoroughly inspect the

machine for any damage, and repair the damage before

restarting and operating the machine.

• Exercise caution to avoid slipping or falling.

• If the machine should start to vibrate abnormally, stop

the engine (motor) and check immediately for the cause.

Vibration is generally a warning sign of trouble.

• Stop the engine (motor) when leaving the operating

position, before unclogging the tines, and when making

any repairs, adjustments and inspections.

• Stop the engine (motor) when leaving the machine

unattended.

• Before cleaning, repairing or inspecting, shut o the

engine and make certain all moving parts have stopped.

Disconnect the spark plug wire, and keep the wire away

from the plug to prevent accidental starting. Disconnect

the cord on electric motors.

• Do not operate tiller under the inuence of alcohol or

drugs.

• Never operate tiller without guards, covers, and hoods in

place.

• Do not overload the machine capacity by attempting to

till or cultivate too deep at too fast a rate.

• Never operate the machine at high transport speeds on

hard or slippery surfaces.

• Never allow bystanders near the machine, especially small

children.

• Use only attachments and accessories approved by the

manufacturer of the machine (such as wheel weights,

counterweights, and the like).

• Never operate the tiller without good visibility or light.

• Be careful when tilling in hard ground. The tines may catch

in the ground and propel the tiller forward. If this occurs,

let go of the handlebars and do not restrain the machine.

• Use extreme caution when reversing or pulling the

machine towards you. To avoid getting pinned against a

structure, ensure adequate distance before reversing near

a wall or fence.

• Do not change the engine governor settings or over

speed the engine.

• Start the engine or switch on the motor carefully

according to instructions and with feet away from the

tines.

• Never pick up or carry a machine while the engine (motor)

is running.

• Powered walk-behind tiller work is strenuous. You must be

in good physical condition and mentally alert. If you have

any condition that might be aggravated by strenuous

work, check with your doctor before operating a powered

walk-behind tiller.

Operator Manual

VICTORY REAR TINE TILLER

Get parts online at www.getearthquake.com or Call 800-345-6007 M-F 8-4:30 CST

MAINTENANCE AND STORAGE

• Keep machine, attachments and accessories in safe

working condition.

• Check shear bolts, engine mounting bolts and other bolts

at frequent intervals for proper tightness to be sure the

equipment is in safe working condition.

• To prevent accidental starting, always disconnect and

secure the spark plug wire from the spark plug before

performing tiller maintenance.

• Pulleys and belts should be kept free of oil or other

moisture for ecient operation.

• Never store equipment with gasoline in the tank inside a

closed building where ignition sources are present, such

as hot water and space heaters, clothes dryers and the like.

Allow engine to cool before storing in any enclosure.

• Always refer to the operator manual instructions for

important details if the tiller is to be stored for an

extended period.

• If the fuel tank has to be drained, do this outdoors.

• Follow manufacturer’s recommendations for safe loading,

unloading, transport and storage of machine.

SAFETY DECALS

This rototiller unit has been designed and manufactured

to provide you with the safety and reliability you would

expect from an industry leader in outdoor power equipment

manufacturing.

Although reading this manual and the safety instructions it

contains will provide you with the necessary basic knowledge

to operate this equipment safely and eectively, there

are several safety labels on the tiller to remind you of this

important information while you are operating the unit.

Please review these decals now, and if you have any

questions regarding its meaning or how to comply with these

instructions, reread the complete safety instruction text in this

manual. For additional questions call Earthquake®Customer

Service.

HAZARD SYMBOLS AND MEANINGS

A: Warning!

B: Avoid Injury From Rotating Tines.

C: Read Operator Manual Before Operating Machine.

D: Remove Objects that Could Be Thrown By This

Machine.

E: Dangerous Moving Parts.

F: Be Aware of Moving and Rotating Parts.

G: Wear Ear and Eye Protection At All Times.

H: Do Not Service or Adjust Moving Parts Unless Engine is

Stopped and Spark Plug Wire is Disconnected.

I: Dress Appropriately And Wear Sturdy Footwear.

J: Toxic Fumes —Do Not Operate in Unventilated Areas.

K: Hot Surfaces.

L: Fire Hazards.

M. Do Not Use In Thunderstorms--For severe weather,

stop operation of this machine and seek shelter.

N. Team Lift--For your safety, always have at least two

people when lifting this machine.

O. Do Not Till Above Underground Utility Lines And

Pipes.

P. Do Not Operate When Children Or Others Are Around.

A B C

DEF

GHI

JKL

MNO

Operator Manual

VICTORY REAR TINE TILLER

Get parts online at www.getearthquake.com or Call 800-345-6007 M-F 8-4:30 CST

FEATURES

DRAG STAKE

DEPTH REGULATOR

LOCK PIN

TINE HOOD

SIDE SHIELD

TINES

WHEEL LOCK PIN

WHEEL

RECOIL

START

CHOKE

THROTTLE

CONTROL

HANDLEBAR

FORWARD DRIVE SAFETY

CONTROL LEVER

REVERSE DRIVE

SAFETY CONTROL

LEVER

FORWARD AND

REVERSE CABLES

HANDLEBAR HEIGHT

ADJUSTMENT

BELT GUARD

ON/OFF SWITCH

Operator Manual

VICTORY REAR TINE TILLER

Get parts online at www.getearthquake.com or Call 800-345-6007 M-F 8-4:30 CST

UNPACKING AND ASSEMBLY

CARTON CONTENTS

• Hardware Parts Bag:

• A - (4) M10 x 45 mm Hex Flange Bolt

• B - (2) M10 x 25 mm Hex Flange Bolt

• C - (6) M10 Nylock Nut

• D - (6) M10 Flat Washer

• E - (6) M6 Flat Washer (small)

• F - (6) M6 x 16 mm Hex Bolt

• G - (6) M6 Nylock Nut

• H - (6) M6 Flat Washer (large)

• I - (1) Lockpin

• J - (2) Handlebar Extensions

• K - (2) LockPin

• Manual Parts Bag

• Unit with Handlebar

• Left and Right Side Shield

• Left and Right Wheel

• Drag Stake

• Bottle of 4-cycle Engine Oil

TILLER ASSEMBLY

1. Open top of carton and remove the handlebar assembly.

2. Cut open seams of carton, exposing all contents and

remove machine by:

a. Attach the loose wheels, in the box, onto the unit

with the wheel lockpins in the free-wheel position.

Slide the wheel all the way onto the axle and insert a

(I) lockpin through the axle hole only. SEE FIGURE 1.

b. Roll the tiller from the carton.

Install the Drag Stake:

3. Locate the drag stake and (I) lockpin. Unscrew the

adjusting knob from the top of the drag stake and slide

the drag stake upwards into the vertical slot at the rear of

the tine shield. SEE FIGURE 2.

4. Reattach the adjusting knob to the top hole of the drag

stake.

5. Insert the lockpin through the hole in the vertical slot and

one of the holes in the drag stake to hold it into place.

SEE FIGURE 2.

WARNING

COMBUSTIBLE DEBRIS CAN CATCH FIRE. IT IS A VIOLATION

OF CALIFORNIA PUBLIC RESOURCE CODE, SECTION 4442,

TO USE OR OPERATE ENGINE-POWERED PRODUCTS ON

ANY FOREST-COVERED, BRUSH-COVERED, OR GRASS-

COVERED LAND UNLESS THE EXHAUST SYSTEM IS

EQUIPPED WITH A SPARK ARRESTER, AS DEFINED IN

SECTION 4442, MAINTAINED IN EFFECTIVE WORKING

ORDER. OTHER STATES OR FEDERAL JURISDICTIONS MAY

HAVE SIMILAR LAWS. CONTACT THE ORIGINAL EQUIPMENT

MANUFACTURER, RETAILER, OR DEALER TO OBTAIN A

SPARK ARRESTER DESIGNED FOR USE WITH THIS PRODUCT.

NOTICE

HANDLE ROTOTILLER WITH CARE. DO NOT DAMAGE

FORWARD CABLE WHEN TRANSPORTING OR OPERATING.

ENGINE IS SHIPPED FROM FACTORY WITHOUT OIL. YOU

MUST ADD ENGINE OIL BEFORE STARTING ENGINE.

FIGURE 1

WHEEL LOCKPIN IN FREE-WHEEL POSITION

AXLE

Operator Manual

VICTORY REAR TINE TILLER

Get parts online at www.getearthquake.com or Call 800-345-6007 M-F 8-4:30 CST

FIGURE 4

FIGURE 2

FIGURE 3

ADJUSTING KNOB

DRAG STAKE

LOCK PIN

Attach the Handlebar:

6. Locate the handlebar extensions and place them on the

outside of the lower handlebar mount. Be sure to line up

the handlebar extension pieces with the lower handlebar

mount as shown. SEE FIGURE 3.

7. Insert one (A) M10 x 45 mm bolt into each of the lower

holes in the side of the extension pieces. The bolts will

pass through the lower hole of the lower handle bar

mount. Place a (D) M10 at washer and a (C) M10 nylock

nut onto the end of each bolt and hand-tighten. SEE

FIGURE 3.

8. Assemble the handlebar to the outside of the handlebar

extension (side opposite the lower handlebar mount).

Insert one (A) M10 x 45 mm bolt into each of the lower

holes in the handlebar and through the middle hole on

the handlebar extension. Place a (D) M10 at washer and

a (C) M10 nylock nut onto the end of each bolt and hand-

tighten. SEE FIGURE 3.

9. Insert one (B) M10 x 25 mm bolt into each top hole on

the handlebar and through one of the three holes on

the handlebar extension according to desired handlebar

height. Place a (D) M10 at washer and a (C) M10 nylock

nut onto the end of each bolt and hand-tighten. SEE

FIGURE 3.

10. Tighten all M10 bolts and nuts that were assembled in the

“Attach the Handlebar” section.

Attach the Side Shields:

11. Locate the side shields and place one up against the side

of the tine guard and hold in place. SEE FIGURE 4.

12. Place one (E) small M6 at washer onto one (F)

M6 x 16 mm bolt. Repeat this process for all three (F)

M6 x 16 mm bolts. Insert the three bolts into the three

holes of the tine guard, making sure they pass through

the side shield as well. Place a (H) large M6 at washer

and a (G) M6 nylock nut onto the bottom of each of the

bolt/washer combinations and tighten all with a wrench/

socket.

NOTE: The side shield needs to be below the tine guard

when they are attached together.

13. Repeat steps 11-12 for the second side shield.

HANDLEBAR

LOWER HANDLEBAR

MOUNT

HANDLEBAR

EXTENSION

THREE HEIGHT

POSITIONS

SIDE SHIELD

TINE GUARD

Operator Manual

VICTORY REAR TINE TILLER

Get parts online at www.getearthquake.com or Call 800-345-6007 M-F 8-4:30 CST

FILL ENGINE CRANKCASE

1. Add oil according to engine manual. DO NOT OVERFILL.

Use a clean, high quality detergent oil. Use no special

additives with recommended oils. DO NOT MIX OIL WITH

GASOLINE. Oil level must be full. Check the oil level by

removing oil ll plug. Oil level should be up to the bottom

of the ll plug opening.

2. Always check oil level before starting engine. Refer to

engine manual for capacity and type of oil to use.

FILL FUEL TANK

1. Add gasoline according to engine manual. DO NOT

OVERFILL. Use 87+ octane unleaded ethanol-free

gasoline. If an ethanol blend must be used, use ethanol

fuel stabilizer. DO NOT MIX OIL WITH GASOLINE.

2. Always check gasoline level before starting engine. Refer

to engine manual for capacity and type of gasoline to use.

WARNING

THIS INFORMATION IS PROVIDED HERE ONLY TO

INTRODUCE THE CONTROLS. DO NOT START THE

ENGINE AT THIS TIME. PLEASE READ THIS SECTION AND

ALL OPERATING AND SAFETY INSTRUCTIONS BEFORE

STARTING YOUR TILLER.

• AS A SAFETY PRECAUTION, THE DRIVE SAFETY CONTROL

LEVER WILL NOT LOCK IN THE FORWARD POSITION.

• TO STOP THE TINES AT ANY TIME, RELEASE THE DRIVE

SAFETY CONTROL LEVER OR RELEASE THE REVERSE

HANDLE.

• DO NOT OPERATE BOTH “FORWARD” AND “REVERSE”

DRIVE SAFETY CONTROL LEVERS AT THE SAME TIME.

• ENGINE SHOULD BE OFF BEFORE ADJUSTING ANY

CONTROLS.

• DO NOT ADJUST TILLING DEPTH UNLESS DRIVE SAFETY

CONTROL LEVER IS RELEASED TO THE NEUTRAL

POSITION.

OPERATION

CONTROLS:

DRIVE SAFETY CONTROL LEVER

Pull the drive safety control lever towards the handlebar to the

FORWARD position to engage the wheels and tines. Releasing

the lever into the NEUTRAL position stops the wheels and tines

and brings the tiller to a complete stop. SEE FIGURE 5.

BELT TENSION ADJUSTMENT

Proper belt tension is critical to good performance. After

1/2 hour of operation, all cables may have to be adjusted due

to initial stretch. Thereafter, check tension after every 10 hours

of operation.

To increase belt tension do as follows:

1. Loosen upper jam nut. SEE FIGURE 6.

2. Tighten the lower jam nut in 1/8" increments, making sure

not to over adjust the tension.

3. When proper adjustment is achieved, tighten upper jam

nut. Tension is properly adjusted when engaging the

drive safety control lever, the beehive spring on the cable

stretches about 1/4 inch or 5 mm longer. SEE FIGURE 6.

NOTE: This procedure can be repeated until conduit

adjustment bolts are fully adjusted. The beehive spring

hook can also be adjusted by inserting in the additional

linkage holes on the drive control lever. If no more

adjustment can be made, belt may need to be replaced.

DRAG STAKE

Tilling depth is controlled by the height of the drag stake. SEE

FIGURE 7.

FIGURE 5

DRIVE SAFETY CONTROL

LEVER DISENGAGED

(NEUTRAL)

REVERSE

LEVER

Operator Manual

VICTORY REAR TINE TILLER

Get parts online at www.getearthquake.com or Call 800-345-6007 M-F 8-4:30 CST

FIGURE 6

To adjust tilling depth do as follows:

1. Remove lock pin.

2. Raise the drag stake to position tines at chosen tilling

depth. Raising the drag stake will allow for deeper tilling.

3. Align hole in drag stake with hole in drag stake mount and

replace lock pin.

WHEEL LOCK PINS

To place wheels in free-wheel position do as follows:

NOTE: This allows wheels to turn freely on the axle for easy

transportation.

1. Remove lockpin. Slide wheel inward toward unit.

SEE FIGURE 8.

2. Insert lockpin through the axle hole only, fold lock ring to

secure pin to axle.

3. Repeat for other wheel.

To place wheels in tilling position do as follows:

NOTE: This locks wheels to the axle so they are able to propel

the unit forward while in use.

1. Remove lockpin. Slide wheel slightly outward away from

unit. Align hole in axle with hole in wheel hub.

SEE FIGURE 9.

2. Insert lockpin through both holes, fold lockpin ring to

secure pin to axle.

3. Repeat for other wheel.

NOTE: Do not operate tiller with only one wheel locked.

1/4"

UPPER JAM NUT

LOWER JAM NUT

REVERSE CABLE

FORWARD CABLE

WARNING

EXTREME CAUTION MUST BE TAKEN IN SELECTING TILLING

DEPTH. IF YOU ATTEMPT TO TILL TOO DEEPLY FOR SOIL

CONDITIONS, THAT IS, WITH THE DRAG STAKE IN TOO

HIGH OF A POSITION, LOSS OF CONTROL AND INJURY TO

PERSONNEL CAN OCCUR.

|ALWAYS SET THE DRAG STAKE LEVER IN THE TRANSPORT

POSITION BEFORE STARTING THE ENGINE. PLACE THE

LOCKPIN IN THE HIGHEST HOLE OF THE DRAG STAKE.

FIGURE 7

DRAG STAKE

BRACKET

LOCKPIN

Deepest Digging

Shallow Digging

Transport hole

SPRING STRETCH

WHEN ENGAGED

Operator Manual

VICTORY REAR TINE TILLER

Get parts online at www.getearthquake.com or Call 800-345-6007 M-F 8-4:30 CST

FIGURE 8

FIGURE 9

WHEEL LOCKPIN IN FREE-WHEEL POSITION

WHEEL LOCKPIN IN TILLING POSITION

(LOCKPIN IN AXLE HOLE AND WHEEL HOLE)

WARNING

DO NOT START YOUR TILLER UNTIL YOU HAVE READ

THE MANUAL THAT CAME WITH YOUR ENGINE, AND

THE SECTIONS IN THIS MANUAL TITLED “CONTROLS”,

“ADJUSTMENTS” AND “SAFETY”. IF YOU HAVE READ THESE,

FOLLOW THE STEPS IN THE FOLLOWING SECTION TO

START YOUR TILLER. ALWAYS PERFORM THIS PRE- START

INSPECTION BEFORE STARTING THE ENGINE. FAILURE TO

FOLLOW WARNINGS CAN CAUSE INJURY OR DEATH.

ENGINE AND SURROUNDING PARTS BECOME EXTREMELY

HOT DURING NORMAL USE. TEMPERATURE OF MUFFLER

AND NEARBY AREAS MAY EXCEED 150°F. THESE AREAS

WILL CAUSE SERIOUS BURN INJURIES IF TOUCHED BEFORE

THE ENGINE HAS COOLED.

WARNING

NEVER START ENGINE OR OPERATE TILLER WITH WHEELS

IN FREE-WHEEL POSITION. ALWAYS SET THE WHEELS IN

TILLING POSITION BEFORE STARTING ENGINE. THE FREE-

WHEEL POSITION IS FOR TRANSPORTING THE TILLER LONG

DISTANCES OVER LEVEL GROUND. DO NOT ATTEMPT TO

MOVE THE TILLER UP OR DOWN STEEP GRADES IN THE

FREE-WHEEL POSITION.

OPERATION

PRESTART INSPECTION:

1. Make sure all safety guards are in place and all nuts and

bolts are secure.

2. Check oil level in engine crankcase. See your engine

manual for procedure and specications.

3. Inspect air cleaner for cleanliness. See your engine manual

for procedure.

4. Check the fuel supply. Fill the fuel tank no closer than one

inch from top of tank to provide space for expansion. See

your engine manual for fuel recommendations.

5. Be sure spark plug wire is attached and spark plug is

tightened securely.

6. Check that position of wheels are locked in the tilling

position.

7. Check drag stake position.

8. Examine underneath and around engine for signs of oil or

fuel leaks.

9. Inspect fuel hoses for tightness and fuel seepage.

10. Look for signs of engine damage.

11. Remove excessive debris from muer area and recoil

starter.

12. Turn fuel shuto valve to the ON position if engine is

equipped with one. It’s located between fuel tank and

carburetor.

Operator Manual

VICTORY REAR TINE TILLER

Get parts online at www.getearthquake.com or Call 800-345-6007 M-F 8-4:30 CST

STARTUP

The controls required to start and run the rototiller are located

on the engine and handlebar, and are the choke lever, throttle

lever and On/O switch. The choke lever is marked on one end

with CHOKE and on the other with RUN. The throttle lever is

marked on one end with a SLOW icon and on the other with a

FAST icon.

A more detailed description of engine operation and all related

precautions and procedures can be found in the engine

manual that accompanies each tiller.

Cold Starts:

1. Turn ON/OFF switch to the ON position.

2. Move choke lever to CHOKE position.

3. Move throttle lever to half way between SLOW and FAST.

4. Pull starting rope out slowly one time and allow to return

normally.

5. Pull starting rope out rapidly, and allow rope to return

normally. Repeat until engine starts.

6. When engine starts, gradually move choke lever to RUN

position and move throttle lever to FAST position for

tilling.

Restarting a Warm Engine:

Restarting an engine that is already warm from previous

running does not normally require use of the choke.

1. Move throttle lever to half way between SLOW and FAST.

2. Pull starting rope out rapidly, and allow rope to return

normally. Repeat until engine starts.

3. Adjust throttle speed to FAST position for tilling.

Idle speed:

Use the SLOW position or a position between SLOW and FAST

on the throttle lever to reduce stress on the engine when

tilling is not being performed. Lowering the engine speed to

“idle” will help extend the life of the motor, as well as conserve

fuel and reduce the noise level of the equipment.

Operating Speed:

For tilling, set the throttle lever to the FAST position.

CAUTION

DO NOT USE THE CHOKE TO STOP ENGINE. IF CHOKE LEVER

IS PLACED IN CHOKE POSITION WHILE ENGINE IS RUNNING,

BACKFIRE OR ENGINE DAMAGE MAY OCCUR.

WARNING

ALWAYS MAINTAIN CONTROL OF YOUR TILLER. ONLY

OPERATE TILLER IN SOIL CONDITIONS THAT ARE CONDUCIVE

TO MAINTAINING CONTROL OF THE TILLER. DO NOT OPERATE

TILLER IN CONDITIONS THAT CONTAIN ROCKS, FOREIGN

OBJECTS, OR ANY OTHER MATERIAL THAT IS NOT SOIL. IF YOUR

TILLER BUMPS, JERKS OR LURCHES, LET GO OF THE HANDLE

BARS AND THE DRIVE CONTROL LEVERS IMMEDIATELY SO

THAT THE TINES AND WHEELS STOP TURNING.

IMMEDIATELY RELEASE THE DRIVE CONTROL LEVER IF THE

TINES JAM OR YOU STRIKE A FOREIGN OBJECT. WITH DRIVE

CONTROL LEVER IN NEUTRAL POSITION, TURN THE ON/OFF

SWITCH TO OFF POSITION TO STOP THE ENGINE. DISENGAGE

THE SPARK PLUG WIRE. WHEN TINES HAVE STOPPED, REMOVE

FOREIGN OBJECTS AND CHECK FOR DAMAGE.

IMPORTANT

PRACTICE OPERATING THE CONTROLS AND TILLER WITH

TINES OUT OF GROUND BEFORE BEGINNING TO TILL. IT

IS IMPORTANT THAT YOU KNOW HOW TO USE THE TILLER

PROPERLY, KEEP CONTROL AT ALL TIMES, STOP THE TINES

AND WHEELS FROM TURNING, AND STOP THE ENGINE IF

NECESSARY. IF YOU DO NOT KNOW HOW TO DO THESE

THINGS, READ THE CONTROLS, ADJUSTMENTS AND

SAFETY SECTIONS BEFORE PROCEEDING.

SHUTTING DOWN

To stop the engine at any time, move the On/O switch to

the OFF position. To stop wheels and tines at any time release

drive safety control levers to NEUTRAL position.

TILLING

1. Adjust the drag stake to desired tilling depth.

NOTE: Raise depth regulator lever up one hole at a time,

testing tiller operation after each raise. Raising the drag

stake too high can result in loss of control of tiller!

2. Move the throttle control to FAST position.

Operator Manual

VICTORY REAR TINE TILLER

Get parts online at www.getearthquake.com or Call 800-345-6007 M-F 8-4:30 CST

3. Place the tiller in FORWARD by pulling the drive safety control.

Tilling tips:

The key to successful tilling is to begin with a shallow cut on

the rst pass, and then work an inch or two deeper on each

successive pass.

• Tilling depth will vary with ground conditions.

• When beginning to till in unbroken ground or in

extremely hard soil, set the lockpin in the highest hole of

the drag stake (SEE OPERATION SECTION). This will allow

for shallow tilling. With the drag stake in this position,

make several light passes over the area to be tilled. Reset

for deeper depths with successive passes.

• If tiller jumps or skids uncontrollably, lower the drag stake

by placing the lockpin in a higher hole. This will allow for

shallower tilling. Hold rmly to the handlebars to control

sudden lurches.

Cultivating tips:

If you plan to use your tiller for cultivating:

• Plant rows on 20” - 22” centers for ease of turning.

• Set the depth regulator lever with the lock pin in one of

the higher holes. This will allow for shallow cultivation

necessary to turn over weeds, and break up and aerate the

soil.

MAINTENANCE

MAINTENANCE SCHEDULE

Your rototiller has been designed and produced by the

industry’s leading manufacturer of outdoor power equipment

to provide you years of reliable operation.

Please read this normal care schedule, and note the

recommended care operating intervals to extend the life of

your unit.

Good maintenance is essential for safe, economical, and

trouble-free operation. Keeping your tiller in top running

condition will prolong its life, and help you obtain optimum

performance. To help you properly care for your tiller, the

following pages include a maintenance schedule, routine

inspection procedures, and simple maintenance procedures

using basic hand tools. Other service tasks that are more

dicult, or require special tools, are best handled by

professionals and are normally performed by a technician or

other qualied mechanic.

WARNING

ENGINE AND SURROUNDING PARTS BECOME EXTREMELY

HOT DURING NORMAL USE. TEMPERATURE OF MUFFLER

AND NEARBY AREAS MAY EXCEED 150° F. THESE AREAS

WILL CAUSE SERIOUS BURN INJURIES IF TOUCHED BEFORE

THE ENGINE HAS COOLED.

WARNING

TO PREVENT ACCIDENTAL STARTING

THE ENGINE MUST BE TURNED

OFF AND COOL, AND SPARK PLUG

WIRE MUST BE REMOVED AND

SECURED FROM SPARK PLUG BEFORE

CHECKING AND ADJUSTING ENGINE

OR EQUIPMENT.

SPARK

PLUG

WIRE

Maintenance, replacement or repair of the emissions control

devices and systems may be performed by any non-road

engine repair establishment or individuals. However, items

must be serviced by a service center to obtain “no charge”

emissions control warranty service. View all service centers in

your area by using our location nder:

www.GetEarthquake.com

The maintenance schedule applies to normal operating

conditions. If you operate your tiller under unusual conditions,

such as sustained high-load or high-temperature operation,

or use in unusually wet or dusty conditions, consult your

servicing dealer for recommendations applicable to your

individual needs and use.

NOTE: For engine maintenance, please refer to the manual

included with your product.

Maintenance Operation Page Before

Each Use

50 hours

or Every

Season

Change forward belt 17 X

Check tiller transmission grease 18 X

Lubrication 19 X

Clean tine axle shaft 19 X

Lubricate wheel axle shaft 19 X

Operator Manual

VICTORY REAR TINE TILLER

Get parts online at www.getearthquake.com or Call 800-345-6007 M-F 8-4:30 CST

SERVICING THE ROTOTILLER

The following information will help you make the necessary

checks and perform the procedures required to follow the

normal care recommendations made for your unit. If you

prefer, your local authorized dealer can make these checks and

perform the required procedures for you.

BELT MAINTENANCE

Check Belt Tension as follows:

Belt tension may decrease over time. It may need to be

adjusted within the rst half hour of operation, and should be

checked after every ten hours of operation. Proper adjustment

will assure long belt life. Too much or too little belt tension will

cause premature belt failure.

An indication that the belt may need to be adjusted can be

heard as a continuous squealing sound when the engagement

lever is compressed, or the belt slips and tines won’t turn.

NOTE: A short buzzing noise can be heard when engagement

lever is released. This is normal, caused by the teeth of the cog

belt catching the wire guide, stopping the rotation of the belt.

This does not require the belt tension to be adjusted.

CHANGE FORWARD/REVERSE BELT

SEE FIGURES 10 AND 11.

1. Turn o engine. Engine must be cool.

2. Remove spark plug wire and secure from spark plug.

3. Remove belt guard.

4. Remove the forward belt from the forward engine pulley:

a. Gently pull the engine recoil rope to rotate the pulley.

With the pulley turning, force the forward belt out of

the V-groove.

b. Slide the belt free of the engine pulley.

c. Pull the forward belt down and out of the way.

5. Remove the reverse belt from the reverse engine pulley:

a. Gently pull the engine recoil rope to rotate the pulley.

With the pulley turning, force the reverse belt out of

the V-groove.

b. Slide the belt free of engine pulleys and reverse belt

guides.

c. Pull belt down and away from transmission pulley.

6. Install new reverse belt:

NOTE: V side of belt should be up, away from pulley.

a. Thread belt up from bottom.

b. Place belt around transmission pulley in groove.

c. Place belt under reverse belt guides.

d. Gently pull engine recoil rope while forcing the belt

over the edge of the engine pulley into the V-groove.

7. Install new forward belt:

a. Place forward belt in transmission pulley groove.

b. Gently pull the engine recoil rope to rotate the pulley

while forcing the forward belt into the V-groove.

8. Replace belt guard.

9. Attach spark plug wire.

FIGURE 10

FIGURE 11

ENGINE PULLEY

FORWARD BELT GUIDE

FORWARD BELT

TRANSMISSION

PULLEY

GUARD BOLT

BELT GUARD

Operator Manual

VICTORY REAR TINE TILLER

Get parts online at www.getearthquake.com or Call 800-345-6007 M-F 8-4:30 CST

CAUTION

DO NOT PUT

ENGINE OIL IN

TRANSMISSION.

LUBRICANT IS

INSTALLED BY

MANUFACTURER.

GEAR CASE

DIPSTICK

FIGURE 12

GEAR CASE

DIPSTICK

TRANSMISSION

COVER PLATE

FIGURE 13

ACCEPTABLE GREASE LEVEL

ADD GREASE

CHECK TILLER TRANSMISSION GREASE

Check the grease level annually. To check the grease level:

1. Tiller must rst be run for approximately 30 minutes to

warm up grease for a proper measurement. Once warm let

sit 5 minutes to allow grease to settle.

2. Move tiller to level ground, making sure the transmission

cover plate is level.

3. Remove the gear case dipstick located between the

handle bar mounts and the engine mount and wipe

grease o dipstick. SEE FIGURE 12.

4. Reinsert the dipstick all the way into the hole port in the

transmission cover plate. SEE FIGURE 13.

5. Remove the dipstick and check grease level. If level is

in the bottom ADD area or not present, add grease in

200ml increments until grease level reaches a proper level

reading. DO NOT OVERFILL. The slashed, acceptable

grease level area on the dipstick has a 200ml range.

NOTE: The front wheel transmission and rear tine

transmission share a common reservoir. Recommended

grease is Mystic 00, or equivalent, transmission grease.

Oil must have an API - E.P (extreme pressure) rating of

GL4 or lower. Higher E.P. rating (ie - GL5, GL6 etc) will

cause the bronze components to soften. For partial ll-ups

(a few ozs or less) use SAE 140W or 85W gear oil or SAE

80W-90 weight gear oil with a API rating of GL4 or GL5.

When replacing grease, the tiller transmission holds 18-

22 ounces. DO NOT OVERFILL.

Operator Manual

VICTORY REAR TINE TILLER

Get parts online at www.getearthquake.com or Call 800-345-6007 M-F 8-4:30 CST

WARNING

DO NOT STORE TILLER IN AN UNVENTILATED AREA WHERE

FUEL FUMES MAY REACH FLAME, SPARKS, PILOT LIGHTS

OR AN IGNITED OBJECT. DRAIN FUEL OUTDOORS AWAY

FROM ANY IGNITION SOURCES. USE ONLY APPROVED

FUEL CONTAINERS.

ENGINE MAINTENANCE

Refer to the engine manual included in your parts packet for

information on engine maintenance. Your engine manual

provides information and a maintenance schedule.

Perform the following tasks:

1. Always check oil level before starting engine. Refer to

engine manual for capacity and type of oil to use.

2. Change oil after rst 5-8 hours of operation. Change oil

while engine is warm. Rell with new oil of recommended

grade.

3. Check spark plug yearly or every 50 hours of operation.

4. Service air cleaner.

5. Keep engine and parts clean.

6. Check engine and equipment often for loose nuts and

bolts, keep these items tightened.

CHECK OR FILL ENGINE CRANKCASE

1. Add oil according to engine manual. Do not overll. Use

a clean, high quality 4-cycle engine oil. Use no special

additives with recommended oils. Do not mix oil with

gasoline. Oil level must be full. Check the oil level by

removing oil ll plug. Oil level should be up to the bottom

of the ll plug opening.

2. Always check oil level before starting engine. Refer to

engine manual for capacity and type of oil to use.

LUBRICATION

Proper lubrication of moving mechanical parts is critical for

proper care and maintenance. Oil the moving parts at 10 hour

intervals using a 30 weight oil.

CLEAN TINE AXLE SHAFT

1. Turn o engine. Engine must be cool.

2. Remove spark plug wire and secure from spark plug.

3. Tip the tiller forward. Block the tiller in position so that it

rests on the engine mount and the tines are exposed.

4. Remove all vegetation, string, wire, and other material that

may have accumulated on the axle between the inside set

of tines and the seal on the transmission housing.

5. Tip the tiller back to a level position.

6. Replace spark plug wire.

STORAGE

PREPARE FOR STORAGE

Follow the steps below to prepare your tiller for storage. Read

your engine manual for detailed instructions on preparing the

engine for storage.

To prepare your tiller for storage do as follows:.

1. Protect wheels and axles from rust:

• Remove lock pin and slide wheel o hub.

• Coat the axles lightly with axle grease.

• Slide wheel back on hub and insert lock pin.

2. Drain fuel system completely following engine

manufacturer’s instructions or add fuel stabilizer to

prevent fuel from gumming up during extended storage

period.

3. While engine is still warm, drain the oil from the engine.

Rell with fresh oil of the recommended grade.

4. Clean external surfaces, engine and cooling fan.

5. Spark plug preparation:

• Remove spark plug, pour one ounce of SAE 30 oil into

spark plug hole.

• Plug hole and pull starter cord slowly to distribute oil

evenly in cylinder head area.

• Reinstall spark plug.

6. Transport unit to a suitable storage location. If you have

chosen to use a fuel stabilizer and have not drained

the fuel system, follow all safety instructions storage

precautions in this manual to prevent the possibility of re

from the ignition of gasoline fumes. Remember, gasoline

fumes can travel to distant sources of ignition and ignite,

causing risk of explosion and re.

7. If there is any possibility of unauthorized use or

tampering, remove the spark plug and store it in a safe

place before storing the rototiller unit. Be sure to plug the

spark plug hole to prevent foreign material from entering.

Operator Manual

VICTORY REAR TINE TILLER

Get parts online at www.getearthquake.com or Call 800-345-6007 M-F 8-4:30 CST

TROUBLESHOOTING AND REPAIR

TROUBLESHOOTING GUIDE

While normal care and routine maintenance will extend the life of your rototiller, prolonged or constant use may eventually

require that service be performed to allow it to continue operating properly. The troubleshooting guide below lists the most

common problems, causes and remedies.

PROBLEM REMEDY/ACTION

Engine will not start • Add gas to gas tank.

• Connect spark plug wire to spark plug

• Throttle must be positioned at choke for a cold start

Engine runs rough, oods during operation • Clean or replace air cleaner

Engine is hard to start • Drain old fuel and replace with fresh. Use gas stabilizer at end of season

• Make sure spark plug wire is securely attached to spark plug

• Drive safety control levers must be released to neutral position to

start the engine

Engine misses or lacks power • Raise the tines for shallow tilling by lowering the depth regulator lever

• Remove and clean fuel tank

• Clean or replace air cleaner

• Improper carburetor adjustment, take to authorized engine service center

• Replace spark plug and adjust gap

• Drain and rell gas tank and carburetor

Tiller moves forward during starting • Drive safety control levers must be released to neutral position to start the engine

Tiller is dicult to control when tilling (machine

jumps or lurches forward)

• Lock wheels in tilling position

• Raise tines for shallower tilling by lowering the depth regulator lever

Tines turn, wheels do not turn • Lock wheels in tilling position

• Internal transmission failure, call customer service

Tines turn, wheels turn, tiller does not move • Raise the tines for shallower tilling by lowering the depth regulator lever

• Lift slightly on handlebars to allow wheels to gain traction

Belts squeal in neutral • Adjust forward belt guide:

- turn engine o and allow muer to cool

- disconnect spark plug wire and secure from spark plug

- remove belt guard

- pull down on drive safety control lever

- manually bend forward belt guide so there is 1/16 inch or less

clearance between belt guide and belt

- replace belt guard and spark plug wire

Excessive heat build up in transmission/tine area

during tilling

• Remove vegetation by following instructions in “Clean Tine Axle Shaft” of

maintenance section.

• Check transmission uid and ll if needed

Constant buzzing sound is heard while engagement

lever is compressed

• Fully compress engagment lever

• Properly space wire guide against idler pulley

• Tighten drive cable

NOTE: If engagement lever is fully compressed, wire guide is properly adjusted, and

cable has reach full adjustment and buzzing persists, the belt may be stretched and

have to be replaced.

La page est en cours de chargement...

EarthQuake 39381 Victory Rear Tine Tiller Manuel utilisateur

Marque: EarthQuake

Modèle: 39381 Victory Rear Tine Tiller

Catégorie: Mini motoculteurs

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: EarthQuake 39381 Victory Rear Tine Tiller User manual