Toro Electric Battery String Trimmer 60V MAX* Flex-Force Power System 51835T

Form No. 3460-833 Rev A

Flex-Force Power System™ 60V MAX String T rimmer

51835T

Flex-Force Power System™ 60V MAX

Faden-Freischneider

51835T

Flex-Force Power System™ – Desbrozadora de hilo

60V MAX

51835T

Débroussailleuse à l Flex-Force Power System™ 60

V MAX

51835T

Decespugliatore Flex-Force Power System™ 60 V

MAX

51835T

Flex-Force Power System™ 60V MAX Draadtrimmer

51835T

Flex-Force Power System™- trådtrimmer , maks. 60 V

51835T

Kosa żyłkowa Flex-Force Power System™ 60V MAX

51835T

Flex-Force Power System™ 60 V MAX trådtrimmer

51835T

www .T oro.com.

*3460-833*

Form No. 3460-819 Rev A

Flex-Force Power System

™

60V

MAX String T rimmer

Model No. 51835T —Serial No. 323000001 and Up

Register at www .T oro.com.

Original Instructions (EN)

*3460-819*

For assistance, please see

www .T oro.com/support

for instructional videos or

contact your Authorized

Service Dealer before

returning this product.

This product complies with all relevant European

directives; for details, please see the separate product

specic Declaration of Conformity (DOC) sheet.

Introduction

This trimmer is intended to be used by residential

homeowners to trim grass as needed outdoors. It is

designed to use T oro 60V lithium-ion battery packs.

These battery packs are designed to be charged only

by T oro 60V lithium-ion battery chargers. Using this

product for purposes other than its intended use could

prove dangerous to you and bystanders.

Important: If you are using this machine with a

battery pack that is 4.0 Ah or greater you must

install quick-release harness Model 139-5334 (not

included) for proper support and balance.

Do not use other harnesses or multiple harnesses

when operating the machine.

Model 51835T does not include a battery or a

charger .

Read this information carefully to learn how to operate

and maintain your product properly and to avoid

injury and product damage. Y ou are responsible for

operating the product properly and safely .

V isit www .T oro.com for product safety and operation

training materials, accessory information, help nding

a dealer , or to register your product.

Whenever you need service, genuine the

manufacturer parts, or additional information, contact

an Authorized Service Dealer or the manufacturer

Customer Service and have the model and serial

numbers of your product ready . Figure 1 identies

the location of the model and serial numbers on the

product. W rite the numbers in the space provided.

Important: W ith your mobile device, you can

scan the QR code on the serial number decal (if

equipped) to access warranty , parts, and other

product information.

g410474

Figure 1

1. Model number , serial number , and QR code location

Model No.

Serial No.

81 1 1 L yndale A venue South

Bloomington, MN 55420

2

Contact us at www .T oro.com.

Printed in China

Safety-Alert Symbol

The safety-alert symbol ( Figure 2 ) shown in this

manual and on the machine identies important safety

messages that you must follow to prevent accidents.

g000502

Figure 2

Safety-alert symbol

The safety-alert symbol appears above information

that alerts you to unsafe actions or situations and

is followed by the word DANGER ,W ARNING , or

CAUTION .

DANGER indicates an imminently hazardous situation

which, if not avoided, will result in death or serious

injury .

W ARNING indicates a potentially hazardous situation

which, if not avoided, could result in death or serious

injury .

CAUTION indicates a potentially hazardous situation

which, if not avoided, may result in minor or moderate

injury .

This manual uses two other words to highlight

information. Important calls attention to special

mechanical information and Note emphasizes general

information worthy of special attention.

Safety

IMPORT ANT SAFETY

INSTRUCTIONS

W ARNING

When using electric gardening tools, always

read and follow basic safety warnings and

instructions to reduce the risk of re, electric

shock, and personal injury , including the

following:

Read All Instructions

I. T raining

1. The operator of the tool is responsible for any

accidents or hazards occurring to others or their

property .

2. Do not allow children to use or play with the

tool, battery pack, or the battery charger; local

regulations may restrict the age of the operator .

3. Do not allow children or untrained people to

operate or service this device. Allow only people

who are responsible, trained, familiar with the

instructions, and physically capable to operate

or service the device.

4. Before using the tool, battery pack, and battery

charger , read all the instructions and cautionary

markings on these products.

5. Become familiar with the controls and proper use

of the tool, battery pack, and battery charger .

II. Preparation

1. Keep bystanders and children away from the

operating area.

2. Use only the battery pack specied by T oro.

Using other accessories and attachments may

increase the risk of injury and re.

3. Plugging the battery charger into an outlet that

is not 100 to 240 V can cause a re or electric

shock. Do not plug the battery charger into an

outlet other than 100 to 240 V . For a dif ferent

style of connection, use an attachment plug

adapter of the proper conguration for the power

outlet if needed.

4. Do not use a damaged or modied battery

pack or battery charger , which may exhibit

unpredictable behavior that results in re,

explosion, or risk of injury .

5. If the supply cord to the battery charger is

damaged, contact an Authorized Service Dealer

to replace it.

3

6. Charge the battery pack with only the battery

charger specied by T oro. A charger suitable for

one type of battery pack may create a risk of re

when used with another battery pack.

7. Charge the battery pack in a well-ventilated area

only .

8. Follow all charging instructions and do

not charge the battery pack outside of the

temperature range specied in the instructions.

Otherwise, you may damage the battery pack

and increase the risk of re.

9. Do not operate the tool without all guards and

other safety protective devices in place and

functioning properly on the tool.

10. Dress properly—W ear appropriate clothing,

including eye protection; long pants; substantial,

slip-resistant footwear; and hearing protection.

T ie back long hair and do not wear loose jewelry

that can get caught in moving parts. W ear a

dust mask in dusty operating conditions.

III. Operation

1. A void dangerous environments—Do not use the

tool in rain or in damp or wet locations.

2. Use the proper tool for your application—Using

the tool for purposes other an its intended use

could prove dangerous to you and bystanders.

3. Prevent unintentional starting—Ensure that the

switch is in the O FF position before connecting

to the battery pack and handling the tool. Do

not carry the tool with your nger on the switch

or energize the tool with the switch in the O N

position.

4. Operate the tool only in daylight or good articial

light.

5. If the tool strikes an object or starts to vibrate,

immediately shut of f the tool, wait for all moving

parts to stop, and disconnect the battery before

examining the tool for damage. Make all

necessary repairs before resuming operation

6. Remove the battery pack from the tool before

adjusting it or changing accessories.

7. Keep your hands and feet away from the cutting

area and all moving parts.

8. Shut of f the tool, remove the battery pack from

the tool, and wait for all movement to stop before

adjusting, servicing, cleaning, or storing the tool.

9. Remove the battery pack from the tool whenever

you leave it unattended.

10. Do not force the tool—Allow the tool to do the

job better and safer at the rate for which it was

designed.

1 1. Do not overreach—Keep proper footing and

balance at all times, especially on slopes. W alk,

never run with the tool.

12. Stay alert—W atch what you are doing and use

common sense when operating the tool. Do not

use the tool while ill, tired, or under the inuence

of alcohol or drugs.

13. Ensure that the ventilation openings are kept

clear of debris.

14. Under abusive conditions, the battery pack may

eject liquid; avoid contact. If you accidently

come into contact with the liquid, ush with

water . If the liquid contacts your eyes, seek

medical help. Liquid ejected from the battery

pack may cause irritation or burns.

15. Do not expose a battery pack or tool to re or

excessive temperature. Exposure to re or

temperature above 130°C (265°F) may cause

explosion.

16. CAUTION—A mistreated battery pack may

present a risk of re, explosion, or chemical

burn.

•Do not disassemble the battery pack.

•Replace the battery pack with a genuine

T oro battery pack only; using another type of

battery pack may cause a re or risk of injury .

•Keep battery packs out of the reach of

children and in the original packaging until

you are ready to use them.

IV . Maintenance and Storage

1. Maintain the tool with care—Keep it clean and

in good repair for best performance and to

reduce the risk of injury . Follow the instructions

for lubricating and changing accessories. Keep

handles dry , clean, and free from oil and grease.

2. When the battery pack is not in use, keep it

away from metal objects such as paper clips,

coins, keys, nails, and screws that can make a

connection from 1 terminal to another . Shorting

the battery terminals may cause burns or a re.

3. Keep your hands and feet away from moving

parts.

4. Shut of f the tool, remove the battery pack from

the tool, and wait for all movement to stop before

adjusting, servicing, cleaning, or storing the tool.

5. Check the tool for damaged parts—If there

are damaged guards or other parts, determine

whether it will operate properly . Check for

misaligned and binding moving parts, broken

parts, mounting, and any other condition that

may af fect its operation. Unless indicated in the

4

instructions, have an Authorized Service Dealer

repair or replace a damaged guard or part.

6. Do not replace the existing non-metallic cutting

means on the tool with a metallic cutting means.

7. Do not attempt to service or repair the tool,

battery pack, or battery charger except as

indicated in the instructions. Have an Authorized

Service Dealer perform service using identical

replacement parts to ensure that the product is

safely maintained.

8. Store an idle tool indoors in a place that is dry ,

secure, and out of the reach of children.

9. Do not dispose of the battery in a re. The

cell may explode. Check with local codes for

possible special disposal instructions.

SA VE THESE

INSTRUCTIONS

5

Safety and Instructional Decals

Safety decals and instructions are easily visible to the operator and are located near any area

of potential danger . Replace any decal that is damaged or missing.

decal139-5220

139-5220

1. Do not discard improperly .

decal139-8262

139-8262

1. W arning—read the Operator ’ s Manual ; wear eye protection;

wear hearing protection; do not expose to rain.

decal139-8263

139-8263

1. W arning—keep

bystanders away from the

machine in all directions.

2. Thrown object

hazard—keep bystanders

away .

6

Setup

Loose Parts

Use the chart below to verify that all parts have been shipped.

Procedure Description

Qty .

Use

1

Allen wrench 1

Unfold the shaft.

2

Auxiliary handle assembly 1 Install the auxiliary handle.

3

Guard

1 Install the guard.

1

Unfolding the Shaft

Parts needed for this procedure:

1 Allen wrench

Procedure

1. Unfold the shaft (A of Figure 3 ).

2. Align the locking button on the lower shaft with the slotted hole on the upper shaft and slide the 2 shafts

together (B and C of Figure 3 ).

Note: The locking button clicks into the slotted hole when both shafts are secured (D of Figure 3 ).

3. Using the provided Allen wrench, tighten the screw on the shaft connector until it is secure (E of Figure 3 ).

7

g280969

Figure 3

8

2

Installing the Auxiliary Handle

Parts needed for this procedure:

1 Auxiliary handle assembly

Procedure

1. Separate the auxiliary handle from the handle plate by removing the 4 socket head screws using the

provided Allen wrench (A of Figure 4 ).

2. Line up the guides on the auxiliary handle plate to the guide on the bottom of the trimmer shaft (B of

Figure 4 ).

3. Line up the auxiliary handle with auxiliary handle plate on the trimmer shaft (C of Figure 4 ).

4. Secure the auxiliary handle to the handle plate with the 4 socket head screws previously removed (D of

Figure 4 ).

g292825

Figure 4

9

3

Installing the Guard

Parts needed for this procedure:

1

Guard

Procedure

1. Using the provided Allen wrench, remove the 2 socket head screws, 2 washers, and 2 spacers from the

trimmer base (A of Figure 5 ).

2. Align the guard onto the trimmer base (B of Figure 5 ).

3. Secure the guard onto the base of the trimmer with the 2 socket head screws, 2 washers, and 2 spacers

previously removed (C of Figure 4 ).

g293134

Figure 5

10

Product Overview

g425180

Figure 6

1. Battery latch 4. Run trigger

2. Lockout trigger

5. Guard

3. Auxiliary handle

6. String

Specications

Model 51835T

Rated

V oltage

60V DC maximum, 54 VDC nominal usage

Charger

T ype

T oro 60V lithium-ion chargers

Battery T ype

T oro 60V lithum-ion batteries*

If you are using this machine with a battery pack that

is 4.0 Ah or greater , you must install quick-release

harness Model 139-5334 (not included).

Appropriate T emperature Ranges

Charge/store the battery pack

at

5°C (41°F) to 40°C (104°F)*

Use the battery pack at

-30°C (-22°F) to 49°C (120°F)

Use the trimmer at

0°C (32°F) to 49°C (120°F)

Store the trimmer at 0°C (32°F) to 49°C (120°F)*

*Charging time will increase if you do not charge the

battery within this range.

Store the tool, battery pack, and battery charger in an

enclosed clean, dry area.

Attachments/Accessories

A selection of T oro approved attachments and

accessories is available for use with the machine

to enhance and expand its capabilities. Contact

your Authorized Service Dealer or authorized T oro

distributor or go to www .T oro.com for a list of all

approved attachments and accessories.

T o ensure optimum performance and continued safety

certication of the machine, use only genuine T oro

replacement parts and accessories. Replacement

parts and accessories made by other manufacturers

could be dangerous.

1 1

Operation

Starting the T rimmer

1. Make sure that the vents on the trimmer are

clear of any dust and debris.

g293133

Figure 7

1. T rimmer venting areas

2. Align the cavity in the battery pack with the

tongue on the handle housing ( Figure 8 ).

3. Push the battery pack into the handle until the

battery locks into the latch ( Figure 8 ).

g268418

Figure 8

1. Battery latch

4. T o start the trimmer , squeeze the lockout trigger ,

then squeeze the variable-speed trigger ( Figure

9).

Note: Slide the speed range switch to change

the speed of the trimmer .

g268420

Figure 9

1. Speed range switch

3. V ariable-speed trigger

2. Lockout trigger

Shutting Off the T rimmer

T o shut of f the trimmer , release both triggers.

Whenever you are not using the trimmer or are

transporting the trimmer to or from the work area,

remove the battery pack.

Removing the Battery Pack

from the T rimmer

Press the battery latch to release the battery pack and

slide the battery pack out of the machine ( Figure 10 ).

g268419

Figure 10

1. Battery latch

12

Advancing the Line Using

the Bump Feed

1. Run the tool at full throttle.

2. T ap the bump button on the ground to advance

the line. The line advances each time the bump

button is tapped. Do not hold the bump button

on the ground.

Note: The line trimming cut-of f blade on the

grass deector cuts the line to the correct length.

Note: If the line is worn too short, you may not

be able to advance the line by tapping it on the

ground. If so, release both triggers and refer to

Advancing the Line Manually ( page 13 ) .

g293135

Figure 1 1

1. Bump button

Advancing the Line

Manually

Remove the battery pack from the trimmer , then push

the bump button at the base of the spool retainer

while pulling on the trimmer line to manually advance

the line.

13

Adjusting the Cutting Swath

The trimmer comes from the factory with a cutting swath of 36.6 cm (14 inches) as shown in A of Figure 12 .

Refer to the following instructions to adjust the swath to 40.6 cm (16 inches) as shown in D of Figure 12 .

1. Remove the swath blade from the bottom of the guard by removing the 2 screws holding it in place using

the provided Allen wrench (B of Figure 12 ) and rotate the swath blade 180°.

2. Once the swath blade is rotated, install it onto the guard using the 2 screws previously removed (C of

Figure 12 ).

g293137

Figure 12

Operating T ips

•Keep the trimmer tilted toward the area being cut;

this is the best cutting area.

•The string trimmer cuts when you move it from left

to right. This prevents the trimmer from throwing

debris at you.

•Use the tip of the string to do the cutting; do not

force the string head into uncut grass.

•Wire and picket fences can cause the string to

wear rapidly and even break. Stone and brick

walls, curbs, and wood can also cause the string

to wear rapidly .

•A void trees and shrubs. The string can easily

damage tree bark, wood moldings, siding, and

fence posts.

g293138

Figure 13

1. Direction of rotation 2. String path

14

Maintenance

After each use of the trimmer , complete the following:

1. Remove the battery from the trimmer .

2. Wipe the trimmer clean with a damp cloth. Do

not hose the trimmer down or submerge it in

water .

CAUTION

The line cutoff blade on the deector is

sharp and can cut you.

Do not use your hands to clean the

deector shield and blade.

3. Wipe or scrape clean the cutting head area any

time there is an accumulation of debris.

4. Check and tighten all fasteners. If any part is

damaged or lost, repair or replace it.

5. Brush debris away from air intake vents and

exhaust on motor housing to prevent the motor

from overheating.

Replacing the String

Use only 2 mm (0.080 inch) monolament string

(T oro Part No. 88201) or 2.4 mm (0.095 inch) twisted

monolament string (T oro Part No. 88202).

1. Remove the battery pack.

2. Remove any old string on the spool by

repetitively pressing the bump button while

pulling the line out equally from both sides of the

trimmer .

3. Cut 1 piece of string according to the following

specications.

•If you are using 2 mm (0.080 inch) string, cut

one piece of line approximately 4.9 m (16 ft).

•If you are using 2.4 mm (0.095 inch) twisted

string, cut one piece of line approximately 3

m (10 ft).

Important: Do not use any other gauge

or type of string, as this could damage the

trimmer .

4. Press and turn the knob on the string head until

arrow on the knob aligns with arrow on the string

head ( Figure 14 ).

5. Insert 1 end of the line at an angle into the LINE

IN eyelet and push the line through the string

head track until it comes out through the eyelet

on the other side. Pull the line though the string

head until the line outside the string is evenly

divided on each side.

g278518

g285202

Figure 14

Disassembled view shown for clarity

1. Arrows 4. Eyelet

2. Knob

5. String

3. String head

6. T rack

Important: Do not disassemble the trimmer

head.

6. Hold the string head in place with one hand. With

your other hand, rotate the knob in the direction

shown by the arrows (counterclockwise).

7. Wind the line, leaving about 102 mm (4 inches)

extending beyond the eyelet on each side.

15

Storage

Important: Store the tool, battery pack, and

charger only in temperatures that are within the

appropriate range; refer to Specications ( page

1 1 ) .

Important: If you are storing the battery pack

for the off-season, charge it until 2 or 3 LED

indicators turn green on the battery . Do not store

a fully charged or fully depleted battery . When

you are ready to use the machine again, charge

the battery pack until the left indicator light turns

green on the charger or all 4 LED indicators turn

green on the battery .

•Disconnect the product from the power supply

(i.e., remove the plug from the power supply or the

battery pack) and check for damage after use.

•Do not store the machine with the battery pack

installed.

•Clean all foreign material from the product.

•When not in use, store the tool, battery pack, and

battery charger out of the reach of children.

•Keep the tool, battery pack, and battery charger

away from corrosive agents, such as garden

chemicals and de-icing salts.

•T o reduce the risk of serious personal injury , do

not store the battery pack outside or in vehicles.

•Store the tool, battery pack, and battery charger

in an enclosed clean, dry area.

16

T roubleshooting

Perform only the steps described in these instructions. All further inspection, maintenance, and repair work

must be performed by an authorized service center or a similarly qualied specialist if you cannot solve the

problem yourself.

Always remove the battery from the tool when troubleshooting, inspecting, maintaining, or cleaning the tool.

Problem

Possible Cause Corrective Action

1. The battery is not fully installed in the

tool.

1. Remove and then replace the battery

into the tool, making sure that it is fully

installed and latched.

2. The battery pack is not charged.

2. Remove the battery pack from the tool

and charge it.

3. The battery pack is over or under the

appropriate temperature range.

3. Move the battery pack to a place

where it is dry and the temperature is

between 5°C (41°F) and 40°C (104°F).

4. There is moisture on the leads of the

battery pack.

4. Allow the battery pack to dry or wipe it

dry .

5. The battery pack is damaged. 5. Replace the battery pack.

The tool does not run or does not run

continuously .

6. There is another electrical problem

with the tool.

6. Contact an Authorized Service Dealer .

1. The battery pack charge capacity is

too low .

1. Remove the battery pack from the tool

and fully charge the battery pack.

The tool does not reach full power or the

motor housing is getting hot.

2. The air vents are blocked.

2. Clean the air vents.

1. There is debris under the grass shield

or in the bump head housing on the

trimmer .

1. Clean any debris from under the grass

shield or in the bump head housing.

The tool is producing excessive vibration

or noise.

2. The spool is not properly wound. 2. Advance the line using the bump head

and/or remove the line on the spool

and wind the spool again.

1. The trimmer is out of line.

1. Add more line to the bump head.

2. The line is tangled in the bump head

housing.

2. Remove the bump head cover and

untangle the line.

The bump head does not advance the line.

3. There is debris under the grass shield

or in the bump head housing on the

trimmer .

3. Clean any debris from under the grass

shield or in the bump head housing.

1. The battery pack is over or under the

appropriate temperature range.

1. Move the battery pack to a place

where it is dry and the temperature is

between 5°C (41°F) and 40°C (104°F).

The battery pack loses charge quickly .

2. The trimmer is overloaded. 2. T rim at a slower pace.

17

EEA/UK Privacy Notice

T oro’ s Use of Y our Personal Information

The T oro Company (“T oro”) respects your privacy . When you purchase our products, we may collect certain personal information about you, either directly

from you or through your local T oro company or dealer . T oro uses this information to full contractual obligations - such as to register your warranty ,

process your warranty claim or to contact you in the event of a product recall - and for legitimate business purposes - such as to gauge customer

satisfaction, improve our products or provide you with product information which may be of interest. T oro may share your information with our subsidiaries,

af liates, dealers or other business partners in connection these activities. W e may also disclose personal information when required by law or in

connection with the sale, purchase or merger of a business. W e will never sell your personal information to any other company for marketing purposes.

Retention of your Personal Information

T oro will keep your personal information as long as it is relevant for the above purposes and in accordance with legal requirements. For more information

about applicable retention periods please contact [email protected] .

T oro’ s Commitment to Security

Y our personal information may be processed in the US or another country which may have less strict data protection laws than your country of residence.

Whenever we transfer your information outside of your country of residence, we will take legally required steps to ensure that appropriate safeguards are

in place to protect your information and to make sure it is treated securely .

Access and Correction

Y ou may have the right to correct or review your personal data, or object to or restrict the processing of your data. T o do so, please contact us by email

at [email protected]. If you have concerns about the way in which T oro has handled your information, we encourage you to raise this directly with us.

Please note that European residents have the right to complain to your Data Protection Authority .

374-0282 Rev C

La page est en cours de chargement...

Toro Electric Battery String Trimmer 60V MAX* Flex-Force Power System 51835T - Tool Only Manuel utilisateur

Toro Electric Battery String Trimmer 60V MAX* Flex-Force Power System 51835T - Tool Only Manuel utilisateur

dans d''autres langues