Simplicity 040366-00 Guide d'installation

Marque: Simplicity

Modèle: 040366-00

Catégorie: Groupes électrogènes

Taper: Guide d'installation

Ce manuel convient également à

Dual 200 Amp - Split 400 Amp

Automatic Transfer Switch

with Service Disconnect and

AC Power Control Module™

Installation Manual

Questions?

Help is just a moment away!

Call: Transfer Switch Helpline

800-743-4115

Monday - Friday 8:00 AM - 5:00 PM Central Standard Time

2 BRIGGSandSTRATTON.COM

Thank you for your purchase of this Briggs & Stratton Power Products® automatic transfer switch. This product is designed for use with

specific home standby generators and may not function with generators or remote modules produced by other manufacturers. Seek a

qualified electrical professional to determine applicability of this equipment to equipment manufactured by others. When operated and

maintained according to the instructions in this manual, your system will provide many years of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with this system and how to avoid them.

We have made every effort to provide for a safe, streamlined and cost-effective installation. As each installation is unique, it is impossible

to know of and advise of all conceivable procedures and methods by which installation might be achieved. We do not know all possible

hazards and/or the results of each possible method or procedure. It is important that you read and understand these instructions thoroughly

before attempting to install or operate this equipment. Save these original instructions for future reference.

This transfer switch requires professional installation before use. Refer to the Installation section of this manual for instructions on

installation procedures. Only licensed electrical contractors should install transfer switches. Installations must strictly comply with all

applicable federal, state and local codes, standards and regulations. Your installer should follow the instructions completely.

Where to Find Us

You never have to look far to find Briggs & Stratton support and service for your system. Consult your Yellow Pages. There are many

authorized service dealers who provide quality service. You can also contact Technical Service by phone at 800-743-4115 between 8:00 AM

and 5:00 PM CT, or click on Find a Dealer at BRIGGSandSTRATTON.COM, which provides a list of authorized dealers.

For Future Reference

Please fill out the information below and keep with your receipt to assist in unit identification for future purchase issues.

Briggs & Stratton Power Products is a registered

trademark of Briggs & Stratton Corporation

Milwaukee, WI, USA

Model Number

Revision

Serial Number

Date Purchased

Table of Contents

Important Safety Instructions .............................4

Installation..........................................5

Owner Responsibilities ...............................................5

Owner Orientation ...................................................5

Installing Dealer/Contractor Responsibilities...............................5

Equipment Description ...............................................5

Delivery Inspection ..................................................6

Mounting Guidelines .................................................6

Power Wiring Interconnections .........................................7

Supervisory Control Wiring ............................................8

System Setup .....................................................12

Testing the Automatic Transfer Switch ..................................13

Controls ...........................................13

Operation..........................................13

Transfer Switch Wiring Diagram ..........................14

Transfer Switch Schematic Diagram .......................15

Troubleshooting .....................................16

Product Specfications .................................16

4 BRIGGSandSTRATTON.COM

Important Safety Instructions

SAVE THESE INSTRUCTIONS - This manual contains important

instructions that should be followed during installation of

the equipment.

Safety Symbols and Meanings

The safety alert symbol indicates a potential personal injury

hazard. A signal word (DANGER, WARNING, or CAUTION) is used

with the alert symbol to designate a degree or level of hazard

seriousness. A safety symbol may be used to represent the type of

hazard. The signal word NOTICE is used to address practices not

related to personal injury.

DANGER indicates a hazard which, if not avoided, will result in

death or serious injury.

WARNING indicates a hazard which, if not avoided, could result

in death or serious injury.

CAUTION indicates a hazard which, if not avoided, could result

in minor or moderate injury.

NOTICE addresses practices not related to personal injury.

The manufacturer cannot possibly anticipate every possible

circumstance that might involve a hazard. The warnings in this

manual, and the tags and decals affixed to the unit are, therefore,

not all-inclusive. If you use a procedure, work method or operating

technique that the manufacturer does not specifically recommend,

you must satisfy yourself that it is safe for you and others. You

must also make sure that the procedure, work method or operating

technique that you choose does not render the equipment unsafe.

Electrical Shock

Read Manual

Save These Instructions

NOTICE Only qualified, licensed electricians should attempt

installation of this equipment, which must strictly comply with

applicable codes, standards and regulations.

WARNING Certain components in this product and related

accessories contain chemicals known to the State of California

to cause cancer, birth defects, or other reproductive harm. Wash

hands after handling.

WARNING Shock Hazard. Installing low and high voltage

wire in same conduit could result in death, serious injury

and/or property damage.

• Do not run low and high voltage wire in the same conduit unless

the insulation rating on ALL wiring is rated for 600V. See NEC

for more information.

WARNING Failure to properly ground equipment could cause

electrocution resulting in death or seriousinjury.

• Do not touch bare wires.

• Do not use equipment with worn, frayed, bare or otherwise

damaged wiring.

• Do not handle electrical cords while standing in water, while

barefoot, or while hands or feet are wet.

• If you must work around a unit while it is operating, stand on an

insulated dry surface to reduce shock hazard.

• Do not allow unqualified persons or children to operate or

service equipment.

• In case of an accident caused by electrical shock, immediately

shut down all sources of electrical power and contact local

authorities. Avoid direct contact with the victim.

WARNING Shock hazard. Equipment contains high voltage

that could result in death, serious injury and/or

property damage.

• DO NOT operate this equipment imprudently or neglect its

maintenance.

NOTICE Improper treatment of equipment could damage it and

shorten its life.

• Use equipment only for intended uses.

• If you have questions about intended use, ask dealer or contact

Briggs & Stratton Power Products.

• Do not expose equipment to excessive moisture, dust, dirt, or

corrosive vapors.

• Remain alert at all times while working on this equipment. Never

work on the equipment when you are physically or

mentally fatigued.

• If connected devices overheat, turn them off and turn off their

circuit breaker/fuse.

Installation

We sincerely appreciate your patronage and have made significant

effort to provide for a safe, streamlined and cost-effective

installation. Because each installation is unique, it is impossible

to know of and advise the trade of all conceivable procedures and

methods by which installation might be achieved. Neither could we

know of possible hazards and/or the results of each method

or procedure.

For these reasons, only current licensed electrical professionals

should attempt system installations. Installations must strictly

comply with all applicable codes, industry standards and

regulations.

Your equipment is supplied with this Installation Manual and a

separate Operator’s Manual. These are important documents and

should be retained by the owner after the installation has

been completed.

Every effort has been made to make sure that the information

in this manual is both accurate and current. However, the

manufacturer reserves the right to change, alter or otherwise

improve the system at any time without prior notice.

Owner Responsibilities

To help you make informed choices and communicate effectively

with your installation contractor(s), read and understand Owner

Orientation before contracting or starting your

equipment installation.

To arrange for proper installation, contact the store at which you

purchased your equipment, your dealer, or your utility

power provider.

The equipment warranty is VOID unless the system is installed by

licensed electrical professionals.

Owner Orientation

The illustrations provided are for typical circumstances and are

meant to familiarize you with the installation options available with

your system.

Local codes, appearance, and distances are the factors that must

be considered when planning an installation. As the distance from

the existing electrical service increases, compensation in wiring

materials must be allowed for. This is necessary to comply with

local codes and overcome electrical voltage drops.

These factors will have a direct effect on the overall price of your

equipment installation.

Your installer must check local codes AND obtain permits before

installing the system.

 • Readandfollowtheinstructionsgiveninthismanual.

 • Followaregularscheduleincaringforandusingyour

equipment, as specified in this manual.

Installing Dealer/Contractor Responsibilities

 • ReadandobservetheImportantSafetyInstructions.

 • Readandfollowtheinstructionsgiveninthismanual.

 • Theinstallermayneedtoprovideappropriateratedcontactors

based on loads to be controlled.

 • Checkfederal,stateandlocalcodesandauthorityhaving

jurisdiction, for questions on installation.

 • Ensuregeneratorisnotoverloadedwithselectedloads.

If you need more information about the transfer switch, call

800-743-4115, between 8:00 AM and 5:00 PM CST.

Equipment Description

The transfer switch is designed to transfer selected loads found

in normal residential installations to standby power in the event

of a primary power outage. The load is connected either to utility

power (normal) or standby power (generator). The transfer switch

monitors utility and generator voltages and will automatically

connect loads to the appropriate source of power.

Only a licensed electrician should complete a standby installation.

Service conduit and conductors can be wired directly from the

watt-hour meter to the transfer switch. A separate service entrance

disconnect and associated wiring is not required when installed per

applicable federal, state and local codes, standards andregulations.

Major components of the transfer switch are three, 2-pole

circuit breakers (one for generator disconnect and two for

utility disconnect), two, 2 pole double throw transfer switches,

transfer switch control circuit board, fused utility terminals and

interconnecting wiring. All of these components are housed in a

NEMA3R enclosure that is suitable for both indoor and outdoor

installations.

The transfer switch is solenoid-operated from utility or generator

inputs and contain suitable mechanical and electrical interlock

switches to eliminate the possibility of connecting the utility service

to the generator output. It has ratings capable of switching full

utility power into the residence. In addition, a manual override lever

is provided for the transfer function.

The control board has active circuits sensing utility and generator

voltages. It creates a signal for generator start-up, switch transfer

and retransfer when utility is restored. The control board also

contains red and green LEDs indicating the power source available

and two relay operated contacts that provide supervisory control of

external loads.

Delivery Inspection

After opening the carton, carefully inspect the transfer

switch components for any damage that may have occurred

duringshipment.

If loss or damage is noted at time of delivery, have the person(s)

making delivery note all damage on the freight bill and affix their

signature under the consignor’s memo of loss or damage. If loss

or damage is noted after delivery, contact the carrier for claim

procedures. Missing or damaged parts are not warranted.

Shipment contents:

 • Automatictransferswitch

 • Installationandoperator’smanuals

 • Currenttransformers(2)

To be supplied by installer:

 • Connectingwireandconduit

 • Variousspecialtytools/equipment

6 BRIGGSandSTRATTON.COM

Mounting Guidelines

The transfer switch system circuitry is enclosed in a NEMA Type3R

enclosure suitable for indoor/outdoor use. Guidelines for mounting

the enclosure include:

 • Installenclosureonafirm,sturdysupportingstructure.

 • Thetransferswitchenclosuremustbeinstalledwith

minimum NEMA3R hardware for conduit connections.

 • Topreventswitchcontactdistortion,levelandplumbthe

enclosure. This can be done by placing washers between the

enclosure and the mounting surface.

 • NEVERinstalltheswitchwhereanycorrosivesubstance

might drip onto the enclosure.

 • Protecttheswitchatalltimesagainstexcessivemoisture,

dust, dirt, lint, construction grit and corrosivevapors.

A typical automatic transfer switch installation is depicted below. It

is best if the transfer switch is mounted near the utility meter, either

inside or outside. Discuss layout suggestions/ changes with the

owner before beginning the system installation process.

NOTICE Before drilling conduit entry holes, or any other holes,

cover and protect the switch and electronics to prevent dirt and

metal fragments from entering the mechanical and electrical

components. Failure to do so may result in damage or malfunction

of the switch.

NOTICE Use a vacuum to clean any dirt or metal shavings inside

the transfer switch. Do not use a blower or compressed air to clean

the inside of the transfer switch because debris may become lodged

in the electrical and mechanical components causing damage or

malfunction.

Control

Wiring

A/C Themostat

Service

Disconnect

Hot

Water

Heater

Air

Conditioner

Distribution

Panel #1

Distribution

Panel #2

Transfer

Switch

Appliance

Generator

Appliance

Branch

Circuits

Branch

Circuits

200 Amp

Utility

200 Amp

Utility

400 Amp

Watt / Hourmeter

BUS

Contactor

Furnace/Air

Handler

text text

200A 200A

Dual 200 Amp

Transfer

Switch

Correct

Dual 200 Amp

Transfer

Switch

text

400A

Dual 200 Amp

Transfer

Switch

text

400A

Incorrect!Incorrect!

NOTICE: The load outputs of the transfer switch

can supply one 200 Amp panel each. These

outputs MUST NOT be combined, or used

individually to supply a panel larger than 200

Amps.

Power Wiring Interconnections

NOTICE Improper installation could cause damage to the circuit

boards and shorten their life. Installing circuit boards in live

circuits will damage the board and is not covered by warranty.

ALWAYS disconnect ALL sources of power prior to servicing.

• Remove all power prior to installing this equipment. Failure to

do so could cause internal damage to the board when making

electrical connections.

• Turn generator to OFF position.

• Turn off utility power to the standby generator and

transferswitch.

All wiring must be the proper gauge, properly supported and

protected by conduit. All wiring should be done per applicable

federal, state and local codes, standards and regulations. Obey

wire type and torque specifications printed on the terminal blocks,

neutral/ground connectors, and installation instructions. Approved

for copper and aluminum conductors.

Use installer supplied 600VAC or greater wire of a gauge that

complies with the latest version of the National Electric Code to

complete the following connections between utility power, transfer

switch, generator, and main distribution panel. Apply the necessary

correction factors and wire size calculations. Refer to the illustration

on pages 9 and 10 for component location.

1. Set generator’s circuit breaker to OFF position.

2. Set generator’s system switch to OFF position.

3. Remove 15 Amp fuse from generator control panel.

4. Turn off utility power to the standby generator and

transfer switch.

5. Locate both 200 Amp utility line circuits coming from the

utility meter.

6. Connect one 200 Amp utility service line circuit to one

transfer switch service disconnect circuit breaker. The

terminal is marked “Utility Connection” (Z1). Repeat for

second 200 Amp utility service line circuit (Z2).

NOTICE: DO NOT wire 400 Amp utility line to this Automatic

Transfer Switch.

7. Connect utility service neutral to transfer switch

neutralterminal (H1 or H2).

8. Connect main distribution panel feeder from first distribution

panel conductors (R1) to transfer switch terminals marked

“LOADCONNECTION (V1)”.

9. Connect main distribution panel feeder from second

distribution panel conductors (R2) to transfer switch

terminals marked “LOADCONNECTION (V2)”.

NOTICE The two individual transfer switch terminals marked

“Load Connection” (V1 and V2) must be connected to separate

distribution panels.

NOTICE Connect the neutrals from both main distribution panels

(S1 and S2) to the transfer switch neutral terminal (H1 and H2).

10. Connect two main distribution panel grounds (T1 and T2) to

transfer switch “GND” terminal (U1 or U2).

Assure grounding electrode conductor is connected and

bonded per applicable federal, state and local codes,

standards and regulations.

11. Connect feeder conductors from transfer switch breaker

“GENERATOR CONNECTION” terminals (Y) to generator

circuit breaker LINE1 and LINE2 terminals (M). Each

conductor must pass through hole of current transformer

(B1 and B2) before making connection.

12. Plug current transformer leads into “CT1” and “CT2”

terminals (E1 and E2) on transfer switch control board.

240V

120V

Neutral

Ground

To Transfer Switch

Line 1 Neutral

Ground

Line 2

Generator

Circuit

Breaker

CT1

CT2

DPSW2

DPSW1

WARNING Shock Hazard. Installing low and high voltage

wire in same conduit could result in death, serious injury

and/or property damage.

• Do not run low and high voltage wire in the same conduit unless

the insulation rating on ALL wiring is rated for 600V. See NEC

for more information.

8 BRIGGSandSTRATTON.COM

13. Connect conductor from transfer switch neutral terminal (H1

or H2) to generator NEUTRAL terminal (L). Observe generator

control panel labeling for terminalidentification.

14. Connect conductor from transfer switch “GND” terminal

(U1 or U2) to generator control panel “GROUND” terminal

(K).

Assure generator equipment grounding conductor (G) is

connected per applicable federal, state and local codes,

standards and regulations.

15. Using minimum #14 AWG conductors, connect the transfer

switch “UTILITY 240 VAC” terminals to generator’s “240

VAC” terminals via two-pole connector supplied

with generator (P).

16. Using #18 AWG twisted pair conductors, no greater than

200 ft. in length, 300 volt minimum, and 75°C minimum,

connect “T/R” and “GND” terminals (B) on transfer switch

control board to the generator’s control panel “TxRx” and

“TxRx GND” terminals via ten pin connector (A) supplied

with generator. Count down to the proper pin location on the

generator control board since visual alignment with its decal

can bemisleading:

17. Tighten all wire connections/fasteners to proper torque.

Supervisory Control Wiring

An air conditioner can be used with the supervisory contacts

on either terminals A-A or B-B. Terminals A-A can only be

used with supervisory control. Large loads can only be used

with contactor control on terminals B-B. Examples of each

system are described below.

1. The terminal strip on the transfer switch control board

has four connections for customer use. There are two

sets of “Normally Closed” contacts available. They will

be activated when generator power is required. These

can be used for supervisory control of large connected

loads on generator. Loads will be allowed to operate if

there is enough generator poweravailable.

For installer convenience, there are two wireways provided to

help keep supervisory load wires organized.

2. Terminals “A-A” on transfer switch control board

are rated for 24VAC. Connect these contacts in

series between air conditioner thermostat and air

conditionercontactor.

3. Terminals “B-B” on transfer switch control board are

rated for 1 Amp 125 VAC. When connected with an

installer supplied contactor, it can be used to control

a large load, such as an electric hot water heater.

Contacts are connected in series with the contactor

control circuit.

To air conditioner contactor

From air conditioner thermostat (yellow?)

24 VAC

Contactor

Neutral

120 VAC

Interconnection Diagram

The illustration on the following pages shows a completed transfer

switch installation. Each installation layout may vary.

Illustration callouts are:

A1 - From Utility to First Service Panel

A2 - From Utility to Second Service Panel

B1 - Current Transformer

B2 - Current Transformer

C - Dipswitches

D - T/R and GND to Generator

E - CT Terminals

F - Transfer Switch Contactors

G - UTILITY 240VAC to Generator

H1 - Transfer Switch Neutral Terminal

H2 - Transfer Switch Neutral Terminal

J - Generator

K - Generator Ground Terminal

L - Generator Neutral Terminal

M - Generator Circuit Breaker

N - Ten pin Connector

P - Two pin Connector

R1 - Main Distribution Panel 1

R2 - Main Distribution Panel 2

S1 - Distribution Panel Neutral Bus

S2 - Distribution Panel Neutral Bus

T1 - Distribution Panel Ground Bus

T2 - Distribution Panel Ground Bus

U1 - Transfer Switch Ground Terminal

U2 - Transfer Switch Ground Terminal

V1 - Load Connections to Distribution Panel 1

V2 - Load Connections to Distribution Panel 2

W1 - Service Entrance Breaker - UTILITY 1

W2 - Service Entrance Breaker - UTILITY 2

X - Generator Disconnect

Y - Generator Connection

Z1 - Utility Connection

Z2 - Utility Connection

10 BRIGGSandSTRATTON.COM

{

FROM

UTILITY

FROM

UTILITY

FROM

GENERATOR

{

LINE2

LINE1

}

FROM

UTILITY

SUPPLY

A1 B1 B2

{

FROM

UTILITY

FROM

UTILITY

FROM

GENERATOR

{

LINE2

LINE1

}

FROM

UTILITY

SUPPLY

R1 R2

12 BRIGGSandSTRATTON.COM

System Setup

You must perform the following before operating the system:

 • Ifgeneratorisinstalledinanarearegularlysubjectedto

temperatures below 40°F (4°C), select a 50 second warm up

time by moving jumper JP2 (C) installed on transfer switch

control board from ‘20’ position to ‘50’position.

 • SettheDPSW1(A) and DPSW2 (B) dipswitches on the

transfer switch control board to match the kW rating of the

standby generator, as described in SettingDipswitches.

Setting Dipswitches

Dipswitches are used to adjust control board operation based

on generator capacity. DPSW1 and DPSW2 switches are set to

correspond to total system kW rating. Dipswitch DPSW1 (A) has

units of 1,000 watts; Dipswitch DPSW2 (B) has units of

10,000 watts.

Set dipswitches with utility and generator power removed from

the transfer switch to ensure proper control system operation.

If dipswitches are set when power is present at transfer switch,

a power reset needs to be performed before the new dipswitch

settings will take effect. Power reset is when all power is removed

from the transfer switch and then reintroduced after 30 seconds.

NOTICE An FC_8 will occur on standby generator control board if

dipswitches are not properly established as noted above.

The “On” position for the dipswitches is the switch number ON

THE TRANSFER SWITCH CONTROL BOARD, not on the switch. For

example, for an 18,000 watt generator, set DPSW2 dipswitch 10 to

“On” position. Set DPSW1 dipswitch 8 to “On” position. 10,000 plus

8000 equals 18,000 watts.

Set only one switch to “On” position

on DPSW1 andDPSW2.

Refer to following chart for proper switch selection(s).

NOTICE

Air density is less at high altitudes, resulting in less

available engine power. Specifically, engine power will decrease 3.5%

for each 1,000 feet (300 meters) above sea level and 1% for each 10°

F (5.6°C) above 77°F (25°C). Generators located in these conditions

must have the transfer switch programmed appropriately for this

power decrease.

DPSW

DPSW2

JP2

NOTICE Use extreme caution when setting dipswitches or

damage to control board will result.

• Use a pencil or small piece of plastic to set the dipswitch.

• NEVER use a screwdriver or any type of metal object to set

dipswitches.

kW Rating

Generator

DPSW

#1 “ON”

Position

DPSW

#2 “ON”

Position

7kW 7 0

8kW 8 0

9kW 9 0

10kW* 0 10

11kW* 1 10

12kW 2 10

13kW* 3 10

14kW 4 10

15kW 5 10

16kW 6 10

17kW 7 10

18kW 8 10

19kW 9 10

20kW 0 20

30kW 0 30

45kW 5 40

48kW 8 40

50kW 0 50

60kW 0 60

* For generators with a rating that includes 500 Watts, round down to

next lowest rating

(example: 13.5 kW set to 13kW)

Testing the Automatic Transfer Switch

Turn both of the utility service disconnect circuit breakers feeding

the transfer switch contactors to the OFF position. The system’s

automatic sequence described below will initiate. To return to utility

power, turn the utility service disconnect circuit breakers to the

ON position.

Utility Fail

The generator senses when utility voltage is below 70percent of

nominal. Engine start sequence is initiated after 6second time

delay.

Engine Warm-Up

There is a time delay to allow for engine warm-up before transfer.

Use jumper on transfer switch control board to select delay of

20seconds or 50 seconds.

Transfer

Transfer from utility to generator supply occurs after voltage is

above set levels and after the initial warm-up period. Minimum

engine run time is 5 minutes after transfer.

Utility Pickup

Voltage pickup level is 80 percent of nominal voltage.

Retransfer

Retransfer from generator to utility power is approximately 10

seconds after utility voltage supply is above pickup level and

minimum run time is completed.

Engine Cool Down

Engine will run for 60 seconds after retransfer.

Controls

Other than a Manual Override lever, there are no operator controls

because this is an automatic transfer switch. The manual override

is to be used only by licensed professionals. Information on handle

use can be obtained by calling Technical Service at 800-743-4115.

Operation

To select automatic transfer operation, do the following:

1. In the transfer switch, set both utility disconnect circuit

breakers to ON position.

2. In the transfer switch, set generator disconnect circuit breaker

to ON position.

3. Install 15 Amp fuse in generator’s control panel.

4. Set generator’s circuit breaker to ON position.

5. Set generator’s system switch to AUTO position.

The system will now be in automatic operation mode.

When the generator is providing power to the transfer switch, the

transfer switch control board is constantly monitoring generator

power. If the air conditioner is called to run, and there is sufficient

generator power available, the controller will close contacts “A-A”

to air conditioner contactor. Contacts “B-B” will open before

contacts A-A close. If loads are too great for the generator, contacts

A-A and/or B-B will open. When air conditioning is not needed, A_A

will open. If enough power is available, B-B will close.

Enclosure Door

To open the transfer switch door, remove the two exterior thumb

screws (A) and carefully lift off door.

To close and secure the door, push door closed against enclosure.

While in this position, the door can rest on the tab (B) at the

bottom of the enclosure. Reinstall both thumb screws to finger

tight. Enclosure door MUST be closed and secured at all times

except when system is being serviced.

When Calling for Assistance

You must have the Model Number and Serial Number from each

transfer switch or remote module ID label at hand if it is necessary

to contact a local service center regarding service or repair. Obtain

this information from the unit ID labels located on or inside device.

For convenience, record the information on the inside front cover of

this manual.

To contact Briggs & Stratton call 800-743-4115, between 8:00 AM

and 5:00 PM CT.

Installation Inspection

Before placing the system into service, inspect the entire installation

carefully.

This completes the installation and startup instructions. The

operator’s manual provides full details on Operation, Maintenance,

and Troubleshooting for the Automatic Transfer Switch.

14 BRIGGSandSTRATTON.COM

Transfer Switch Wiring Diagram

Transfer Switch Schematic Diagram

16 BRIGGSandSTRATTON.COM

Automatic Transfer Switch

Product Specfications

Model 071058

Rated Maximum Load Current Per Contactor

at 77°F (25°C)* .............................................................200 Amps

Rated AC Voltage. ..............................................................250 Volts

Poles Per Contactor ........................................................................ 2

Frequency ................................................................................60 Hz

Fault Current Rating .................25,000 RMS Symmetrical Amperes

Normal Operating Range ...............-20°F (-28.8°C) to 104°F (40°C)

Weight ......................................................................110 lbs (50 kg)

Dimensions (HxWxD) ....37in. x 24in. x 7in.(94cm x 61cm x 18cm)

This transfer switch is a UL Listed device.

Troubleshooting

Problem Cause Correction

Au tomatic transfer switch does not

transfer to generator

1. Generator breaker open.

2. Generator voltage not acceptable.

3. Generator disconnect circuit breaker open in

transfer switch.

1. Reset generator circuit breaker.

2. Refer to generator manual.

3. Reset generator disconnect circuit breaker

in transfer switch.

Au tomatic transfer switch does not

transfer to utility

1. Utility disconnect circuit breakers open in

transfer switch.

2. Utility voltage not acceptable.

1. Reset utility disconnect circuit breaker in

transfer switch.

2. Wait for utility voltage to return tonormal.

Ge nerator is still running after switch

transfers to utility power

Engine cool down period. Engine should stop after 1 minute.

Ge nerator or supervised loads (air

conditioner, etc.) are operating

improperly when generator is

supplyingpower

1. AA and/or BB are not operatingcorrectly.

2. Too much load on generator.

3. Current transformer not connected.

4. Broken current transformer.

1. Five minute delay timer has notexpired.

2. Decrease load to generator.

3. Contact local authorized servicecenter.

4. Contact local authorized servicecenter.

Ge nerator is still running after utility

power is restored

1. Minimum engine run time has notelapsed.

2. Fuse(s) in transfer switch isdefective.

1. Wait five minutes for transfer switch to

retransfer to utility power.

2. Contact local authorized servicecenter.

Manual de instalación

Dual 200 Amperios - División 400 Amperios

Interruptor de transferencia automática

con seccionador de servicio y

módulo de control de

energía eléctrica de CA™

Preguntas?

La ayuda es justa un momentolejos!

Llamada: Línea Directa de generador de hogar

800-743-4115 M-F 8-5 CT

2 BRIGGSandSTRATTON.COM

Gracias por comprar este conectador automático de Briggs & Stratton Power Products®. Este producto está diseñado para utilizarse con

generadores de reserva domésticos específicos y puede no funcionar con generadores o módulos remotos producidos por otros fabricantes.

Recurra a un electricista profesional cualificado para determinar si este equipo se puede utilizar con equipo fabricado por terceros. Si se

utiliza y mantiene de acuerdo con las instrucciones de este manual, su sistema le proporcionará muchos años de funcionamiento fiable.

Este manual contiene información de seguridad para que usted conozca los peligros y riesgos propios de este sistema y cómo evitarlos.

Se ha realizado el máximo esfuerzo para que la instalación resulte segura, sencilla y económica. Debido a que cada instalación es única,

es imposible conocer y recomendar todos los procedimientos y métodos posibles para efectuarla. No conocemos todos los riesgos y/o

resultados posibles de cada método o procedimiento existente. Es importante que lea y comprenda perfectamente estas instrucciones antes

de intentar instalar o utilizar este equipo. Guarde estas instrucciones para futuras consultas.

Este conectador deben ser instalados por un profesional antes de utilizarlos. Consulte la sección de instalación de este manual. Los

conectadores sólo deben ser instalados por electricistas con licencia. Las instalaciones deben cumplir estrictamente la totalidad de los

códigos, estándares y regulaciones federales, estatales y locales vigentes. El instalador debe seguir las instrucciones detalladamente.

Ubicación

Nunca debe ir demasiado lejos para encontrar el soporte y servicio de Briggs & Stratton para su sistema. Consulte las Páginas

Amarillas. Existen múltiples distribuidores de servicio autorizados que ofrecen un servicio de calidad. También puede comunicarse

con el Servicio Técnico por teléfono al 800-743-4115 entre 8:00 a. m. y 5:00 p. m. Hora del Centro; o bien, busque un distribuidor en

BRIGGSandSTRATTON.COM, donde se incluye una lista de distribuidores autorizados.

Para futuras consultas

Llene la siguiente información y conserve su factura para facilitar la identificación de la unidad en caso de que surjan problemas relacionados

con la compra en el futuro.

Milwaukee, WI, USA. Reservados todos los derechos.

Briggs & Stratton Power Products es una marca

registradas de Briggs & Stratton Corporation

Milwaukee, WI, USA

Conectador automático

Número de modelo

Revisión

Número de serie

Fecha de compra

Tabla de contenido

Instrucciones importantes deseguridad ......................4

Instalación ..........................................5

Responsabilidades del propietario.......................................5

Orientación al propietario .............................................5

Re sponsabilidades del distribuidor / técnicoinstalador ......................5

Descripción del equipo ...............................................5

Inspección en el momento de la entrega..................................6

Directrices de montaje................................................6

Interconexión de los cables de alimentación...............................7

Terminales de control de supervisión ....................................9

Configuración del sistema ............................................12

Prueba del conectador automático .....................................13

Controles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Funcionamiento .....................................14

Resolución de problemas...............................15

Especificaciones del producto............................16

4 BRIGGSandSTRATTON.COM

Instrucciones importantes deseguridad

GUARDE ESTAS INSTRUCCIONES - Este manual contiene

instrucciones importantes que se deben seguir durante la

instalación y el mantenimiento delequipo.

Símbolos sobre la seguridad y significados

El símbolo de alerta de seguridad indica un posible riesgo

para su integridad física. Se utiliza una palabra de señalización

(PELIGRO, ADVERTENCIA o ATENCIÓN) junto con el símbolo de

alerta para designar un grado o nivel de gravedad de riesgo. Se

puede utilizar un símbolo de seguridad para representar el tipo

de riesgo. La palabra de señalización AVISO se utiliza para hacer

referencia a una práctica no relacionada con una lesión física.

PELIGRO indica un riesgo que, de no evitarse, provocará la

muerte o lesiones de gravedad.

ADVERTENCIA indica un riesgo que, de no evitarse, podría

provocar la muerte o lesiones de gravedad.

ATENCIÓN indica un riesgo que, de no evitarse, podría provocar

lesiones leves o moderadas.

AVISO hace referencia a una práctica no relacionada con una lesión

física.

El fabricante no puede prever toda circunstancia que conlleve

un riesgo potencial. Por tanto, las advertencias de este manual,

así como las etiquetas y calcomanías adheridas a la unidad, no

incluyen todos los riesgos posibles. Si utiliza un procedimiento,

método de trabajo o técnica de uso no recomendado

específicamente por el fabricante, deberá asegurarse de que es

seguro tanto para usted como para otras personas. También deberá

asegurarse de que el procedimiento, método de trabajo o técnica de

uso que elija no hace que el equipo sea inseguro.

Guarde estas instrucciones

Descarga eléctrica

Lea el manual

AVISO La instalación de este equipo debe cumplir estrictamente

la totalidad de los códigos, estándares y regulaciones vigentes,

por lo que sólo debe ser llevada a cabo por un electricista

cualificado.

ADVERTENCIA Determinados componentes en este producto

y los accesorios relacionados contienen sustancias químicas

declaradas cancerígenas, causantes de malformaciones, y otros

defectos congénitos por el Estado de California. Lávese las

manos después de manipular estos elementos.

ADVERTENCIA Peligro de descarga. La instalación de un

cable de baja y alta tensión en el mismo conducto podría

provocar daños materiales, lesiones graves o incluso la

muerte.

• No tienda un cable de baja y alta tensión en el mismo conducto

a menos que el valor nominal de aislamiento en TODO el

cableado sea de 600 V. Para obtener más información, consulte

el NEC.

ADVERTENCIA Una conexión a tierra defectuosa del equipo

podría provocar electrocución, así como lesiones graves

o incluso la muerte.

• No toque los cables pelados.

• No utilice el equipo con cables desgastados, deshilachados o

deteriorados de cualquier otra forma.

• No manipule los cables eléctricos si se encuentra en una zona

húmeda, está descalzo o tiene las manos o los piesmojados.

• Si tiene que trabajar junto a una unidad en funcionamiento,

manténgase en una superficie aislada y seca para reducir el

riesgo de descarga eléctrica.

• No permita que personas no cualificadas o niños utilicen o

reparen el equipo.

• En caso de accidente provocado por una descarga eléctrica,

desconecte inmediatamente todos los suministros de energía

eléctrica y póngase en contacto con las autoridades locales.

Evite el contacto directo con la víctima.

AVISO Un tratamiento inadecuado del equipo podría estropearlo

y acortar su vida útil.

• Utilice el equipo sólo para los usos previstos.

• En caso de dudas sobre su uso, diríjase al distribuidor o a Briggs

& Stratton Power Products.

• No exponga el equipo a un exceso de humedad, polvo, suciedad

o vapores corrosivos.

• Manténgase alerta en todo momento cuando utilice este equipo.

Nunca lo utilice ni manipule en condiciones de fatiga física o

mental.

• Si se calientan excesivamente los dispositivos conectados,

apáguelos y abra sus interruptores o quite sus fusibles.

ADVERTENCIA Peligro de descarga eléctrica. El equipo

contiene alto voltaje que podría provocar daños

materiales, lesiones graves y/o la muerte.

• NO utilice este equipo con imprudencia ni descuide su

mantenimiento.

La page est en cours de chargement...

Simplicity 040366-00 Guide d'installation

Marque: Simplicity

Modèle: 040366-00

Catégorie: Groupes électrogènes

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Simplicity 040366-00 Installation guide
español: Simplicity 040366-00 Guía de instalación

Simplicity 040366-00 Guide d'installation

Ce manuel convient également à

Simplicity 040366-00 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents