Legrand DRD2 Wireless Incandescent Dimmer, Miro decorator style Guide d'installation

Legrand
Marque
Legrand
Modèle
DRD2 Wireless Incandescent Dimmer, Miro decorator style
Catégorie
Gradateurs
Taper
Guide d'installation
Specifications
Operating Voltage . . . . . . . . . . . . . . . . . . . . . . . . 120VAC, 60Hz
Maximum Load Rating . . . . . . . . . . . . . . . . . . . . . . . . . . . 600W
Minimum Load Required . . . . . . . . . . . . . . . . . . . . . . . . . . 60W
Load Type Compatibility . . . . . . . . . . . . . . . . . . . . . . . .60-600W
Incandescent (tungsten/quartz halogen)
DRD2
Wireless Incandescent Dimmer
U.S. Patent 6,175,220. Other utility,
design, and foreigh patents pending.
Installation Instructions
UNIT DESCRIPTION
The Miro Decorator Wireless devices use radio signals to communicate with
each other to control lighting and other types of electric loads in selected
areas. Miro Decorator wireless devices use the 900MHz band for high-speed
control communication. Using the patented “frequency-agile” Top Dog™
technology, Miro Decorator wireless devices avoid interference with other
900MHz devices, such as cordless phones and baby monitors.
Load Types
Use the DRD2 incandescent dimmer for these load types (60-600W at 120V):
• Incandescent & quartz halogen lamps
Do not mix different load types on the same dimmer.
Do not use with diode equipped (some types of energy saving) lamps.
Do not use for motors.
For dimmable, 2-wire fluorescent and compact fluorescent fixtures, magnetic
or electronic low voltage, neon or cold cathode fixtures or diode equipped
lamps, use the Miro DRD4 wireless universal dimmer, or the Miro DCD267
universal dimmer.
Derating
When more than one dimmer is installed in a multi-gang box, it is necessary to
reduce the maximum load on each dimmer.
• For a dimmer in either end position of a multi-gang box, reduce its
maximum load by 100W.
• For a dimmer in a central position of a multi-gang box, reduce its maximum
load by 200W.
CAUTION
To reduce the risk of
overheating and possible
damage to other equipment, do
not install to control a receptacle,
a motor-operated appliance, or a
fluorescent lighting fixture.
CAUTION
Afin de réduire le risque de
surchauffe et la possibilité
d’endommager d’autres matériels,
ne pas installer pour commander
une prise, un appareil à moteur,
ou une lampe fluorescente.
GND
LOAD
LINE
GND
LOAD
LINE
INSTALLATION
For ease of installation, manufacturer recommends use of a deep wall box.
1. Disconnect power to circuit by turning circuit breaker OFF before
installation.
2. Remove existing wall plate and switch.
3. Strip existing wires 1/2”. If two wires will be connected to the same terminal
on a Miro device, both wires must be the same gauge (12AWG or 14AWG).
4. Wire the LINE (black), LOAD and GND supply wires to the correspondingly
marked screw terminals, according to one of the wiring diagrams below.
5. If NEUTRAL wires are provided to the fixture, connect them together using
a wire nut. The dimmer does not use a neutral connection.
6. Attach the wall plate.
7. Switch the circuit breaker back ON.
INSTALL IN COMPLIANCE WITH ALL APPLICABLE
CODES & STANDARDS.
Failure to follow these instructions may cause
personal injury or equipment damage.
DRD2 wiring Switch-leg circuit wiring, to replace
a single-pole light switch
CAUTION
TURN THE POWER OFF AT THE CIRCUIT BREAKER
BEFORE INSTALLING THE DIMMER.
SET HOUSE ID
All Miro wireless devices installed in the same home must acquire the same
unique House ID before use. This process is known as house binding. Each
Miro wireless device is bound to all other Miro wireless devices in the house.
New Installation
1. With all devices installed and energized, make sure that every Miro wireless
device LED is yellow. If any LED is off, be sure the circuit breaker is on and
the device is correctly installed.
2. Press
on any device paddle
until the LED flashes yellow (about
2 seconds). This indicates that it
has acquired a unique House ID.
3. Make sure that all other Miro
wireless device LEDs are flashing
green, indicating that they have
acquired the same House ID.
4. Return to the device used in step 2, which is still flashing yellow. Press
until the LED changes to solid green (about 2 seconds). All device LEDs in
the house change to solid green, indicating house binding is complete.
Adding a Device to an Existing Installation
If you’re adding or replacing a device in a Miro wireless installation that is
already operating, the new device must acquire the same House ID as the
other Miro wireless devices in the house. After the new device is powered up,
the LED should be solid yellow. This indicates that it has not yet acquired a
House ID. To acquire the House ID for the existing system:
1. Press
on any previously bound device until the LED flashes yellow (about
2 seconds).
2. Verify that the newly added device LED is flashing green, indicating that it
has acquired the House ID.
3. Return to the same previously bound device used in step 1 and press
until the LED changes to solid green (about 2 seconds). All device LEDs
should now be solid green.
When you see
in the instructions,
firmly press and
hold both the top
and bottom of the
device paddle until
the LED changes
(about 2 seconds).
OPERATION
Tap once Fade the load to its last-used level
Tap twice Full bright
—— Press and hold Increase the present level
Tap once Fade the load to OFF
—— Press and hold Decrease the present level
When you
see
in the
instructions,
touch the top of
the paddle as
directed.
When you
see
in the
instructions,
touch the
bottom of the
paddle as
directed.
The dimmer may feel warm to the touch during normal operation.
Replacing Lamps
When a lamp must be replaced, use the Air Gap Isolation feature for safety.
To activate the feature:
Press
FIRMLY, so that the paddle clicks and latches in.
Make sure the status LED is extinguished, indicating that it’s safe to
relamp.
To release and return to normal operation, press . The status LED lights.
Power Fail Memory
After a power failure, all Miro devices automatically return to the state that
they were in immediately prior to loss of power. All configuration and scene
control information is preserved.
ADVANCED OPERATION
Groups
Use a Miro wireless incandescent dimmer in conjunction with one or more Miro
DRD8 Wireless Multilocation Controllers to control one lighting circuit from
multiple locations. Binding the DRD2 and DRD8 devices together in the same
Group enables them to work in exactly the same way, from any of the control
locations.
You can include other Miro wireless devices in the Group. Just remember that
all devices in the Group operate when one member operates. If you increase
the brightness on one circuit in the Group, all circuits will increase brightness.
Set the House ID (see Set House ID) before setting up Groups.
Creating a New Group
1. Go to any device that you want to include in the Grou
p. Press . The device
LED flashes yellow, and all other devices in the House flash green.
You now have 5 minutes to complete this process.
2. To include or exclude a device in the Group press
on the device until the
LED changes color. Yellow flashing LED = Included in the Group
Green flashing LED = NOT included in the Group
If you get to a device and it is NOT flashing, the 5 minute binding process
timer may have expired. Go back to step 1 and repeat.
3. Return to the device used in step 1 and press
to terminate Group binding.
All LEDs revert to solid green. Now, all the devices in the Group control
their load circuit in exactly the same manner.
Adding a Dimmer to a Group in an Existing System
1. Go to a device that is in the Group where you want to add the dimmer.
Press
. The device LED and all members of the Group flash yellow.
The new dimmer flashes green.
2. Press on the new dimmer until its LED flashes yellow.
3. Return to the device used in step 1 and press
. All LEDs are solid green.
Scene Control
The Miro wireless incandescent dimmer may be easily incorporated into room
and whole house preset scenes. The Miro Installation Guide provides more
information about confi guring scenes and presets.
Instructions for installation and use are included with the relevant Miro
wireless room and whole house control devices. Application support
information and the Miro Installation Guide are available online.
CLEANING
Clean using a cloth dampened only with water and a little mild detergent.
Use of solvents or hydrocarbon-based cleaners may cause permanent
damage.
TROUBLESHOOTING
During Set House ID, the LED is not flashing on some wireless Miro
devices.
• If LED is solid green before initiating House ID binding:
The device already has another House ID. Reset it to the factory default
so that it can be bound to the desired House ID. Resetting to factory
defaults is described in the “I need to start over” issue.
• If LED is solid yellow after initiating House ID binding:
The device may be out of range of the initiating device. Add a MRR2G
Miro Wireless Repeater to boost signal range.
I made a configuration mistake. I need to start over.
You can reset any Miro wireless device to factory default settings by
pressing and holding
until the LED changes to solid yellow (ap-
proximately 10 seconds). During the process, the LED flashes yellow
and when complete, it changes to solid yellow. The device can then be
reconfigured, exactly like any new device (see the Set House ID section).
The dimmer does not work and the status LED is flashing red.
• at 2Hz (10 times in 5 seconds):
The dimmer has detected an overload condition and has shut down.
To clear the fault condition, tap
and wait for the LED to turn green.
Disconnect loads in excess of rated load and try again.
• at 3Hz (15 times in 5 seconds):
The dimmer has detected a short-circuit condition and has shut down.
To clear the fault condition, tap
and wait for the LED to turn green.
Remove power, rectify the short-circuit condition, restore power, and
try again.
FCC NOTICE
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by
manufacturer could void your authority to operate this equipment.
Warranty Information
Manufacturer warranties its products to be free of defects in materials and
workmanship for a period of fi ve (5) years. There are no obligations or liabilities
on the part of manufacturer for consequential damages arising out of, or
in connection with, the use or performance of this product or other indirect
damages with respect to loss of property, revenue or profi t, or cost of removal,
installation or reinstallation.
2800 De La Cruz Blvd.
Santa Clara, CA 95050
Phone: 800.879.8585
www.wattstopper.com
Please
Recycle
1061 South 800 East
Orem, UT 84057
Phone: 800.555.9891
www.vantagecontrols.com
Watt Stopper Customers contact: Vantage Customers contact:
05737r2 09/07
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Legrand DRD2 Wireless Incandescent Dimmer, Miro decorator style Guide d'installation

Legrand
Marque
Legrand
Modèle
DRD2 Wireless Incandescent Dimmer, Miro decorator style
Catégorie
Gradateurs
Taper
Guide d'installation
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes