Samsung RF263BEAESR Manuel utilisateur

imagine the possibilities

RF263TE****

RF263BE****

Free Standing Appliance

English

Refrigerator

user manual

Thank you for purchasing this Samsung product.

DA68-02601A-16.indb 1 2018. 10. 8. 오후 4:31

2_ Safety information

safety information

SAFETY INFORMATION

• Before using your new Samsung Refrigerator,

please read this manual thoroughly to ensure

that you know how to operate the features and

functions that your new appliance oers safely

and eciently.

• This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities, or

lack of experience and knowledge, unless they

have been given supervision or instruction

concerning use of the appliance by a person

responsible for their safety. Children should be

supervised to ensure that they do not play with

the appliance.

• Because the following instructions cover

various models, the characteristics of your

refrigerator may dier slightly from the

refrigerator described in this manual.

• If you have any question, contact us at

1-800-SAMSUNG or ﬁnd help and information

online at www.samsung.com.

• R-600a or R-134a is used as a refrigerant.

Check the compressor label on the rear of

the appliance or the rating label inside the

fridge to see which refrigerant is used for your

refrigerator. If this product contains ﬂammable

gas (Refrigerant R-600a), contact your local

authority in regard to safe disposal of this

product.

• It is hazardous for anyone other than an

Authorized Service Person to service this

appliance.

Warning :

Risk of ﬁre

/ ﬂammable

materials

Important safety symbols and

precautions:

WARNING

Hazards or unsafe practices that may result in

severe personal injury or death.

CAUTION

Hazards or unsafe practices that may result in

minor personal injury or property damage.

Do NOT attempt.

Do NOT disassemble.

Do NOT touch.

Follow directions carefully.

Unplug the power plug from the wall socket.

Make sure the refrigerator is grounded

to prevent electric shock.

Call the contact center for help.

Note.

These warning signs are here to prevent

injury to you and others.

Please follow them carefully.

After reading this section, keep it in a safe

place for future reference.

STATE OF CALIFORNIA

PROPOSITION 65

WARNING

• Cancer and Reproductive Harm - www.

P65Warnings.ca.gov.

SEVERE WARNING SIGNS

FOR INSTALLATION

• Do not install the refrigerator in a damp

place or place where it may come in

contact with water.

- Deteriorated insulation of electrical parts may

cause an electric shock or ﬁre.

• Do not place this refrigerator in direct sunlight

or expose to the heat from stoves, room

heaters or other appliance.

• Do not plug several appliances into the same

multiple power strip. The refrigerator should

always be plugged into its own individual

electrical outlet which has a voltage rating that

matches the voltage listed on the refrigerator’s

rating plate.

- This provides the best performance and

also prevents overloading house wiring

WARNING

DA68-02601A-16.indb 2 2018. 10. 8. 오후 4:31

Safety information _3

circuits, which could cause a ﬁre hazard from

overheated wires.

• If the wall socket is loose, do not insert the

power plug.

- There is a risk of electric shock of ﬁre.

• Do not use a cord that shows cracks or

abrasion damage along its length or at either

end.

• Do not bend the power cord excessively or

place heavy articles on it.

- Do not pull or excessively bend the power

cord.

• Do not twist or tie the power cord.

• Do not hook the power cord over a metal

object, place a heavy object on the power

cord, insert the power cord between objects,

or push the power cord into the space behind

the appliance.

- When moving the refrigerator, be careful not to

roll over or damage the power cord.

- This may result in an electric shock or ﬁre.

• This appliance should be positioned in such a

way that it is accessible to the power plug.

- Failing to do so may result in an electric shock

or ﬁre due to electric leakage.

• Keep ventilation opening in the appliance

enclosure or mounting structure clear of

obstruction.

• Do not attempt to repair, disassemble, or

modify the appliance yourself.

- Do not use any fuse(such as cooper, steel

wire, etc.) other than the standard fuse.

- hen repairing or reinstalling the appliance is

required, contact your nearest service center.

- Failing to do so may result in an electric shock,

ﬁre, problems with the product, or injury.

• To get the best energy eciency of this

product, please leave all selves, drawers and

baskets on their original position like as above

illustration.

• Never unplug your refrigerator by pulling on the

power cord. Always grip plug ﬁrmly and pull

straight out from the outlet.

- Damage to the cord may cause a short-circuit,

ﬁre and/or electric shock.

• Do not use aerosols near the refrigerator.

- Aerosols used near the refrigerator may cause

an explosion or ﬁre.

• Do not install this appliance near a heater,

inﬂammable material.

• Do not install this appliance in a humid, oily or

dusty location, in a location exposed to direct

sunlight and water (rain drops).

• Do not install this appliance in a location where

gas may leak.

- This may result in an electric shock or ﬁre.

• This refrigerator must be properly

installed and located in accordance

with the manual before you use it.

• Connect the power plug in the proper position

with the cord hanging down.

- If you connect the power plug upside down,

the wire can get cut o and cause a ﬁre or

electric shock.

• When moving the refrigerator, be careful not to

roll over or damage the power cord.

- This constitutes a ﬁre hazard.

• Make sure that the power plug is not

squashed or damaged by the back of the

refrigerator.

• Keep the packing materials out of reach of

children.

- There is a risk of death from suocation if a

child puts the packing materials on his or her

head.

• The appliance must be positioned so that the

plug is accessible after installation.

• You need to remove all the protective plastic

ﬁlm before you initially plug the product in.

• The refrigerator must be safely

grounded.

- Always make sure that you have grounded the

refrigerator before attempting to investigate

or repair any part of the appliance. Power

leakages can cause severe electric shock.

• Never use gas pipes, telephone lines or other

potential lightning attractors as an electrical

ground.

- Improper use of the grounding plug can result

in a risk of electric shock. If it is necessary

to use an extension cord, use only a 3-wire

extension cord that has a 3-blade grounding

plug and a 3-slot receptacle that will accept

the plug on the appliance. The marked rating

of the extension cord should be AC115-

120 V, 10 A, or more. If a grounding adapter

is used, make sure the receptacle box is fully

grounded.

• If the power cord is damaged,

have it replaced immediately by the

manufacturer or its service agent.

• The wall socket must be easily accessible so

that the appliance can be quickly disconnected

from the wall socket in an emergency.

• It must be outside the area of the rear of the

appliance.

DA68-02601A-16.indb 3 2018. 10. 8. 오후 4:31

4_ Safety information

• When positioning the appliance, ensure the

power cord is not trapped or damaged.

• Do not locate multiple portable socket-outlets

or portable power supplies at the rear of the

appliance.

• Do not store explosive substances such as

aerosol cans with a ﬂammable propellant in

this appliance.

INSTALLATION CAUTIONS

• Allow sucient space to install the

refrigerator on a ﬂat surface.

- If your refrigerator is not level, the internal

cooling system may not work correctly.

• Keep the ventilation space in the appliance

enclosure or mounting structure clear of

obstruction.

• Allow the appliance to stand for 2 hours after

installation.

• We recommend you have installed this

refrigerator by a qualiﬁed technician or service

company.

- Failing to do so may result in an electric shock,

ﬁre, explosion, problems with the product, or

injury.

• This appliance must be properly grounded.

• Do not ground the appliance to a gas pipe,

plastic water pipe, or telephone line.

- You must ground the refrigerator to prevent

any power leakages or electric shocks caused

by current leakage from the refrigerator.

- This may result in an electric shock, ﬁre,

explosion, or problems with the product.

- Never plug the power cord into a socket that is

not grounded correctly and make sure that it is

in accordance with local and national codes.

• Plug the power plug into the wall socket ﬁrmly.

Do not use a damaged power plug, damaged

power cord or loose wall socket.

- This may result in an electric shock or ﬁre.

• The installation or any service of this appliance

is recommended by a qualiﬁed technician or

service company.

• Failing to do so may result in an electric shock,

ﬁre, explosion, problems with the product, or

injury.

• Do not touch the power plug with wet hands.

- This may result in an electric shock.

• Do not store articles on the top of the

appliance.

• When you open or close the door, the articles

may fall and cause personal injury and/or

material damage.

• Do not use or place any substances sensitive

CAUTION

to temperature such as inﬂammable sprays,

inﬂammable objects, dry ice, medicine, or

chemicals near or inside of the refrigerator.

• Do not keep volatile or inﬂammable objects or

substances (benzene, thinner, propane gas,

alcohol, ether, LP gas and other such products

etc.) in the refrigerator.

- This refrigerator is for storing food only.

- This may result in ﬁre or explosion.

• If you smell pharmaceutical or smoke, pull

out power plug immediately and contact your

Samsung Electronics service center

CRITICAL USAGE

WARNINGS

• Do not insert the power plug with wet

hands.

• Do not store articles on the top of the

appliance.

- When you open or close the door, the articles

may fall and cause personal injury and/or

material damage.

• Do not put a container ﬁlled with water on the

refrigerator.

- If spilled, there is a risk of ﬁre or electric shock.

• Children should be supervised to ensure that

they do not play with the appliance.

- Keep ﬁngers out of “pinch point” areas;

clearances between the doors and cabinet are

necessarily small. Be careful when you open

the doors when children are in the area.

• Do not let children hang on the door. A serious

injury may occur.

• Do not let children go inside the refrigerator.

Children could become trapped.

• Do not insert your hands into the bottom area

under the appliance.

- Any sharp edges may cause personal injury.

• Do not let children step on a drawer’s cover.

- The drawer may break and cause them to slip.

• Do not overﬁll the refrigerator with food.

- When you open the door, an item may fall out

and cause personal injury or material damage.

• Do not touch the inside walls of the freezer or

products stored in the freezer with wet hands.

- This may cause frostbite.

• Never put ﬁngers or other objects into the

water dispenser hole, ice chute, or ice maker

bucket.

- It may cause personal injury or material

damage.

WARNING

DA68-02601A-16.indb 4 2018. 10. 8. 오후 4:31

Safety information _5

• Do not spray ﬂammable gas near the

refrigerator.

- There is a risk of explosion or ﬁre.

• Do not store volatile or ﬂammable substances

in the refrigerator.

- The storage of benzene, thinner, alcohol, ether,

LP gas and other such products may cause

explosions.

• Do not store pharmaceuticals products,

scientiﬁc materials, or temperature sensitive

products in the refrigerator.

- Products that require strict temperature

controls must not be stored in the refrigerator.

• Do not place or use an electrical appliance

inside the refrigerator, unless it is of a type

recommended by the manufacturer. Do not

stand on top of the appliance or place objects

(such as laundry, lighted candles, lighted

cigarettes, dishes, chemicals, metal objects,

etc.) on the appliance. This may result in an

electric shock, ﬁre, problems with the product,

or injury. Do not put a container ﬁlled with

water on the appliance.

- If spilled, there is a risk of ﬁre or electric shock.

• Do not use mechanical devices or any other

means to accelerate the defrosting process,

other than those recommended by the

manufacturer.

• Do not damage the refrigerant circuit.

• Do not spray volatile material such as

insecticide onto the surface of the appliance.

- As well as being harmful to humans, it may

also result in an electric shock, ﬁre or problems

with the product.

• Never stare directly at the UV LED lamp for

long periods of time.

- This may result in eye strain due to the

ultraviolet rays.

• Do not disassemble or repair the

refrigerator by yourself.

- You run risk of causing a ﬁre, malfunction and/

or personal injury.

- When the interior or exterior LED lamp has

gone out, please contact your service agents.

• Children should be supervised to

ensure that they do not play with the

appliance.

- Keep ﬁngers out of “pinch point” areas :

clearances between the doors and cabinet are

necessarily small. Be careful when you open

the doors when children are in the area. Do not

let children hang on the door. If not, a serious

injury may occur. Risk of children entrapment.

Do not let children enter inside the refrigerator.

• Bottles should be stored tightly together so

that they do not fall out.

• This product is intended only for the storage of

food in a domestic environment.

• If a gas leak is detected, avoid any naked

ﬂames or potential sources of ignition and air

the room in which the appliance is standing for

several minutes.

- Do not touch the appliance or power cord.

- Do not use a ventilating fan.

- A spark may result in explosion or ﬁre.

• If the products is equipped with the LED

Lamp, do not disassemble Lamp Cover and

LED Lamp by yourself.

- Please contact your service agent.

• Use only the LED Lamps provided by

manufacturer or service agent.

a) Allow the appliance to stand for 2 hours after

installation.

b) To get Best performance from the product,

1) Do not place foods too closely in front of

the vents at the rear of the appliance as it

can obstruct free air circulation in the freezer

compartment.

2) Wrap the food up properly or place it in

airtight containers before putting it into the

fridge or freezer.

3) Do not put any newly introduced food for

freezing near to already existing food.

c) Do not place glass or bottles or carbonated

beverages into the freezer.

- The container may freeze and break, and this

may result in injury.

d) Please observe maximum storage times and

expiry dates of frozen goods.

e) There is no need to disconnect the refrigerator

from the power supply if you will be away for

less than three weeks. But, Remove all the food

if you are going away for the three weeks or

more. Unplug the refrigerator and clean it, rinse

and dry.

• Remove all foreign substances such as dust

or water from the power plug terminals and

contact points using a dry cloth on a regular

basis.

- Unplug the power plug and clean it with a dry

cloth.

- Failing to do so may result in an electric shock

or ﬁre.

• Before cleaning or performing maintenance,

unplug the appliance from the wall socket.

- Failing to do so may result in an electric shock

or ﬁre.

DA68-02601A-16.indb 5 2018. 10. 8. 오후 4:31

6_ Safety information

• If there are burning smells or smoke,

pull out power plug immediately and

contact your Samsung Electronics

service center.

• If you experience diculty when changing the

light, contact a service agent.

• If the product is equipped with LED Lamps,

do not disassemble the Lamp Cover and LED

Lamp by yourself.

- Please contact your service agents.

• If any dust or water is in refrigerator, pull out

the power plug and contact your Samsung

Electronics service center.

- Otherwise there is a risk of ﬁre.

USAGE CAUTIONS

• Do not re-freeze frozen foods that

have thawed completely. Do not place

carbonated or ﬁzzy drinks in the freezer

compartment. Do not put bottles or

glass containers in the freezer.

- When the contents freeze, the glass may break

and cause personal injury.

• Use only the ice maker provided with

the refrigerator. The water supply to this

refrigerator must only be installed/connected

by a suitably qualiﬁed person and connected

to a potable water supply only. In order to

operate the ice maker properly, water pressure

of 20 ~ 125 psi is required. If you have a long

vacation or business trip and won’t use water

or ice dispensers, close the water valve.

- Otherwise, water leakage may occur.

• Wipe excess moisture from the inside and

leave the doors open.

- Otherwise, odor and mold may develop.

• Service warranty and Modiﬁcation.

- Any changes or modiﬁcations performed by

a 3rd party on this ﬁnished appliance are not

covered under Samsung warranty service, nor

can Samsung be responsible for safety issues

that result from 3rd party modiﬁcations.

• Do not block air holes.

- If the air holes are blocked, especially with

a plastic bag, the refrigerator can be over

cooled. If this cooling period lasts too long,

the water ﬁlter may break and cause water

leakage.

• If the refrigerator is disconnected from the

power supply, you should wait for at least ﬁve

minutes before plugging it back in.

CAUTION

• If you have a long vacation planned or the

refrigerator is not to be used for a long period

of time, you must empty the refrigerator and

pull out the power plug.

- Letting the refrigerator run for a long time

without using it can cause the insulation to

deteriorate and may cause a ﬁre.

- Wipe excess moisture from the inside and

leave the doors open. Otherwise, odor and

mold may develop.

• To get the best performance from the product:

- Do not place foods too close to the vents at

the rear of the appliance as it can obstruct free

air circulation in the refrigerator compartment.

- Wrap food up properly or place it in airtight

containers before putting it into the refrigerator.

• Fill the water tank, ice tray, and water cubes

only with potable water.

• If the product is ﬂooded, make sure to

contact your nearest service center.

- There is a risk of electric shock or ﬁre.

• Do not keep vegetable oil in your refrigerator’s

door bins. The oil can solidify, making it foul-

tasting and dicult to use. In addition, the

open container can leak and the leaked oil can

cause the door bin to crack. After opening an

oil container, it is best to keep the container in

a cool and shaded place such as a cupboard

or pantry.

- Examples of vegetable oil: olive oil, corn oil,

grape-seed oil, etc.

CLEANING CAUTIONS

• Do not directly spray water on the

inside or outside the refrigerator.

- There is a risk of ﬁre or electric shock.

• Do not use a hair dryer to dry the inside of the

refrigerator. Do not place a lighted candle in

the refrigerator to remove bad odors.

- This may result in an electric shock or ﬁre.

• Remove any foreign matter or dust

from the power plug pins. Do not use

a wet or damp cloth when cleaning

the plug.

- Otherwise, there is a risk of ﬁre or electric

shock.

• Unplug the refrigerator before cleaning

or making repairs.

CAUTION

DA68-02601A-16.indb 6 2018. 10. 8. 오후 4:31

Safety information _7

• Use a clean sponge or soft cloth and a

mild detergent in warm water to clean the

refrigerator.

• Do not use abrasive or harsh cleansers

such as window sprays, scouring cleansers,

ﬂammable ﬂuids, muriatic acid, cleaning

waxes, concentrated detergents, bleaches, or

cleansers containing petroleum products on

exterior surfaces (doors and cabinet), plastic

parts, door and interior liners, and gaskets.

- These can scratch or damage the material.

• Do not clean glass shelves or covers with

warm water when they are cold. Glass shelves

and covers may break if exposed to sudden

temperature changes or impacts such as

bumping or dropping.

CRITICAL DISPOSAL

WARNINGS

• Risk of child entrapment. Before you

throw away your old refrigerator or

freezer:

- Take o the doors.

- Leave the shelves in place so that children may

not easily climb inside.

Please dispose of the packaging material from

this product in an environmentally friendly

manner.

• Leave the shelves in place so that children

can not easily climb inside. Ensure that none

of the pipes on the back of the appliance are

damaged prior to disposal.

• R600a or R134a is used as a refrigerant.

• Check the compressor label on the rear of

the appliance or the rating label inside the

fridge to see which refrigerant is used for your

refrigerator. If this product contains ﬂammable

gas (Refrigerant R600a), contact your local

authority in regard to safe disposal of this

product.

WARNING

• When disposing of this refrigerator, remove

the door/door seals and door latch so that

small children or animals cannot become

trapped inside. Children should be supervised

to ensure that they do not play with the

appliance.

• Cyclopentane is used in the insulation. The

gases in the insulation material require a

special disposal procedure. Please contact

your local authorities in regard to the

environmentally safe disposal of this product.

Ensure that none of the pipes on the back of

the refrigerator are damaged prior to disposal.

• When you use this function the energy

consumption of the refrigerator will increase.

• Remember to turn it o when you don’t

need it and return the freezer to your original

temperature setting.

power freezing

• If you need to freeze large amount of food

stu, activate Power Freeze function at least

24 hours before.

• Never put ﬁngers or other objects into the

dispenser hole, ice chute and ice maker

bucket.

- It may cause a personal injury or material

damage.

THIS APPLIANCE IS INTENDED

TO BE USED IN HOUSEHOLD

AND SIMILAR APPLICATIONS

SUCH AS

• sta kitchen areas in shops, oces and other

working environments;

• farm houses and by clients in hotels, motels

and other residential type environments;

• bed and breakfast type environments;

• catering and similar non-retail applications.

contents

SETTING UP YOUR FRENCH DOOR REFRIGERATOR ………………………………… 08

OPERATING YOUR FRENCH DOOR REFRIGERATOR …………………………………… 16

TROUBLESHOOTING ………………………………………………………………………… 28

DA68-02601A-16.indb 7 2018. 10. 8. 오후 4:31

8_ setting up

Setting up your French Door

Refrigerator

GETTING READY TO INSTALL

THE REFRIGERATOR

Congratulations on your purchase of this Samsung

French Door Refrigerator.

We hope you enjoy the state-of-art features and

eciencies that this new appliance oers.

Selecting the best location for the refrigerator

Choose:

• A location with easy access to a water supply.

• A location without direct exposure to sunlight.

• A location with a level ﬂoor.

• A location with enough space for the

refrigerator doors to open easily.

• A location that allows sucient space to the

right, left, back and top for air circulation.

• A location that allows you to move the

refrigerator easily if it needs maintenance or

service.

• Do not install the refrigerator where the

temperature will go below 50 ºF (10 ºC).

• Do not locate the refrigerator where it may

become wet.

When moving your refrigerator

To prevent ﬂoor damage, be sure the

front adjusting legs are in the up position

(above the ﬂoor). Refer to ‘Adjusting the

Level’ in the manual (on page 12).

Flat-blade screw

driver(-)

Control Lever

CAUTION

B

A

C

E

D

B

A

C

E

D

Model RF263T**/ RF263B**

Depth “A” 33 1/2” (850mm)

Width “B” 35 3/4” (909mm)

Height “C” 68 3/8” (1737mm)

Overall Height “D” 70” (1778mm)

Depth “E” 35 3/4” (910mm)

63 3/4

”

(1620 mm)

13 3/8”

(340 mm)

140° 140°

2”

(50 mm)

35 3/4”

(909 mm)

29 1/4”

(745 mm)

48 ”

(1220 mm)

1 5/8”

(40 mm)

3 3/4”

(95 mm)

• The measurements here are based on

the design dimension, which may dier

depending on the measuring method.

DA68-02601A-16.indb 8 2018. 10. 8. 오후 4:31

setting up _9

01 SETTING UP

FLOORING

For proper installation, you must place this

refrigerator on a level, hard surface that is the

same height as the rest of the ﬂoor. This surface

should be strong enough to support a fully loaded

refrigerator, or approximately 335lbs (152kg).

To protect the ﬁnish of the ﬂooring, cut a large

section of the cardboard carton and place it under

the refrigerator where you are working. When

moving the refrigerator, you need to pull and push

it straight forwards or back. Do not wiggle it from

side to side.

REQUIRED TOOLS

Required Tools (Not provided)

You need the following tools to complete the

installation of your refrigerator:

Philips

screwdriver(+)

Flat-blade screw

driver(-)

Socket wrench

(10mm)

Allen wrench

(3/16”) (5mm)

REMOVING THE REFRIGERATOR

DOORS

For some installations you need to remove the

fridge and freezer drawers so you can move the

refrigerator to its ﬁnal location. Do not remove

the doors/drawer if you don’t need to. If you do

not need to remove the refrigerator doors, go to

Adjusting the Level on page 12. If you need to

remove the doors. continue below.

Before removing the door/drawer, make sure you

read the following items:

Disconnect power to the refrigerator

before removing the door or drawer.

• Be careful not to drop, damage or

scratch the door/drawer while removing

them.

• Use care when you remove the doors/drawer.

The doors are heavy and you could injure

yourself.

• Reattach the doors/drawer properly to avoid:

- Moisture from air leakage.

- Uneven door alignment.

- Wasting energy due to improper door seal.

HOW TO ASSEMBLE THE HANDLE

Orient each handle so that the end with the sticker

attached is at the top and the holes with the

tightening screws are facing each other.

Then, follow the directions below to install each

handle.

By using Phillips screwdriver, ﬁx the screw

(optional) and then put the handle on the ﬁxer by

sliding them down ﬁrmly.

WARNING

DA68-02601A-16.indb 9 2018. 10. 8. 오후 4:31

10_ setting up

2

1

3

5

4

Fix the handles to the doors

by sliding them down ﬁrmly.

Screw

Tighten with wrench ﬁrmly

Drawer door handle assembly

Check the direction of

Handle assembly.

1

2

Fix the handles to the

doors by sliding them

side ﬁrmly.

3

Fix the handles to the doors by sliding them left

side ﬁrmly.

4

5

Tilt up the Handle bar and tighten with wrench

ﬁrmly.

Disassembling the refrigerator doors

Be careful not to drop and scratch the

doors while removing them.

With the door opened

1. Remove 3 screws holding down the TOP

TABLE ( 1 ) and turn it with wires connected.

( 1 )

WARNING

DA68-02601A-16.indb 10 2018. 10. 8. 오후 4:31

setting up _11

01 SETTING UP

2. Disconnect two connectors ( 2 ) on the left

side door. To remove the water coupler from

the hinge, twist and pull it from the hinge.

Remove the water line ( 3 ) while pressing the

marked part ( 4 ) of the water line coupler.

If a red clip is on the coupler, it must be

removed before removing the tube.

2

3

4

Red Clip

(1/4”)

3. Pull and remove the hinge lever ( 5 ). Remove

the ground screw ( 6 ) attached to the upper

left door hinges with a philips screwdriver (+).

Remove the upper left and right door hinges

( 7 ).

5

6

7

4. Lift the door straight up to remove.

5. Remove the screw ( 8 ) attached to the

lower left and right door hinges with a philips

screwdriver (+). Remove the 2 hex head bolts

( 9 ) attached to the lower left and right door

hinges with an allen wrench (3/16”). Remove

the lower left and right door hinges ( 10 ).

Allen wrench

10

8

9

CAUTION

REATTACHING THE

REFRIGERATOR DOORS

To reattach the fridge doors after you have moved

the fridge to its ﬁnal location, assemble the parts

in reverse order.

1. The Water Line must be fully Inserted to the

center of transparent coupler to prevent water

leakage from the dispenser.

2. Insert the clip in the top plate and check that it

Center of transparent coupler

The Guide Lines

Dispenser

- TYPE A - - TYPE B -

By placing the 3 screws again ensure

that the wires are in not to damage the

harness.

DISASSEMBLING THE FLEX DOOR

1. Take out the upper drawer by lifting it up.

2. Take out the lower basket ( 1 ) by lifting the

basket up from the rail system.

1

3. Press the ﬁxing hook of rail system.

CAUTION

DA68-02601A-16.indb 11 2018. 10. 8. 오후 4:32

12_ setting up

4. Holding the top of the Freezer Drawer, pull it

out all the way and then remove it from the rail

system.

Be careful not to scratch or dent the

sliding rail by letting it strike the ﬂoor.

Make sure that you mount the freezer

basket in the right position when

removing / installing the freezer door.

Failing to do so may result in the door not

opening or closing properly.

ASSEMBLE THE FREEZER

DRAWER

To reattach the drawer after you have moved the

fridge to its ﬁnal location, assemble the parts in

reverse order.

ADJUSTING THE LEVEL

Make sure the refrigerator is level so that you can

make ﬁnal adjustments. Use a level to test if the

refrigerator is level both side to side and back to

front. If the refrigerator is not level, it will not be

possible to get the doors perfectly even, which

may cause moisture condensation and increased

energy bills. Below is an example of how to level

the refrigerator if the left side of the refrigerator is

lower than the right side.

CAUTION

How to adjust the level

1. Open the freezer drawer and remove the lower

basket.

2. Insert a ﬂat-blade screwdriver (-) into the

notch on the left control lever, and then turn

it counter-clockwise to level the refrigerator.

(You turn the lever clockwise to lower the

refrigerator and counterclockwise to raise it.)

ﬂat-blade screwdriver (-) Control Lever

Both control levers must be touching the

ﬂoor to avoid possible personal injury or

property damage because of tipping.

• If the right side is lower, perform the

same procedure, but with the right

control lever.

• It is dicult to remove the cover leg

front from the refrigerator, so we do not

recommend making small adjustments

with the control lever. Instead, refer to

the next page for the best way to make

minor adjustments to the doors.

MAKING MINOR

ADJUSTMENTS TO THE

DOORS

Remember, a leveled refrigerator is necessary

for getting the doors perfectly even. If you need

help, review the previous section on leveling the

refrigerator.

Adjustment

part

Fixed part

• The left door is ﬁxed. To make minor

adjustments between doors, adjust only

the right door.

CAUTION

DA68-02601A-16.indb 12 2018. 10. 8. 오후 4:32

setting up _13

02 SETTING UP

1. Pull out the freezer drawer ( 1 ), then you can

see the lower hinge ( 2 ).

2. Insert a philips screwdriver (+) ( 3 ) into the

shaft ( 4 ) of the lower hinge.

3. Adjust the height by turning a philips

screwdriver (+) ( 3 ) clockwise (

DOWN

) or

counterclockwise (

UP

).

• When you turn a philips screwdriver (+)

counterclockwise (

UP

), the door will

move up.

1

2

3

4

3

INSTALLING THE WATER

DISPENSER LINE

A water dispenser with a ﬁlter is one of the helpful

features on your new refrigerator. To help promote

better health, the water ﬁlter removes unwanted

particles from your water. However, it does not

sterilize or destroy microorganisms. You may need

to purchase a water purifying system to do that.

The water line also connects to the ice maker.

For the ice maker to operate properly, water

pressure of 20~125psi (138~862 kPa) is required.

If the refrigerator is installed in an area with low

water pressure (below 20psi), you can install

a booster pump to compensate for the low

pressure.

After you have connected the water line, make

sure the water storage tank inside the refrigerator

is properly ﬁlled. To do this, press the water

dispenser lever until the water runs from the water

outlet.

• Water line installation kits are available at

extra cost from your dealer.

We recommend using a water line

installation kit that contains copper

tubing and a ¼” compression nut.

• Use the new hose-sets supplied with the

appliance only. Do not re-use an old hose set.

Keep ventilation openings, in the

appliance enclosure or in the built-in

structure, clear of obstruction. Connect

to potable water supply only.

Connecting to the water supply line

1. First, shut o the main water

supply.

2. Locate the nearest cold water drinking line and

install the pipe clamp and shut o valve.

Pipe clamp

Cold water line

Shut o valve

3. Connect the water line installation kit to the

shut o valve.

Shut o valve

Pipe clamp

Cold water line

Water line installation kit

Connecting the water supply line to

the refrigerator.

There are several items that you need to purchase

to complete this connection.

You may ﬁnd these items sold as a kit at your local

hardware store.

Use Copper Tubing Use Plastic Tubing

• ¼” copper tubing

• ¼” compression nut (1pc)

• Ferrule (2pc)

• ¼” plastic tubing

- Molded end(Bulb)

• ¼” compression nut (1pc)

WARNING

DA68-02601A-16.indb 13 2018. 10. 8. 오후 4:32

14_ setting up

Compression

Nut (1/4”)

(Assembled)

Ferrule

(Not supplied)

Plastic Tubing

(Assembled)

Compression

Fitting

(Assembled)

Molded

end(Bulb)

Compression

nut (B) (1/4”)

(Not supplied)

or

Copper tubing

(Not supplied)

Plastic tubing (B)

(Not supplied)

Household water supply line

Refrigerator

1. Connect the household water line to the

assembled compression ﬁtting.

- If you are using copper tubing, slip the

compression nut ( B ) (not supplied) and

ferrule (not supplied) on the copper tubing (not

supplied) as shown.

- If you are using plastic tubing ( B ) , insert the

molded end (Bulb) of the plastic tubing ( B ) into

the compression ﬁtting.

Do not use without the molded end (Bulb)

of the plastic tubing ( B ).

2. Tighten the compression nut ( B ) onto the

compression ﬁtting.

Do not over-tighten the compression nut ( B ).

3. Turn the water on and check for any leakage.

If you ﬁnd water drops or leakage in the

connection areas, turn o the main water

supply. Check the connections and, if

necessary, tighten.

4. Flush 1 gallon of water through the ﬁlter

before drinking or using the water from the

refrigerator. (Flush approximately 6 minutes.)

To ﬂush, press a large glass or cup against the

water dispenser lever. Fill the glass, empty it

into the kitchen sink after it is ﬁlled, and then

repeat.

5. After you turn on the refrigerator, let the ice

maker make ice for 1 to 2 days. Over that

period of time, throw out the ﬁrst 1 or 2

CAUTION

buckets of ice the freezer makes to ensure all

impurities have been removed from the water

line.

• Only connect the water line to a

drinkable water source.

• If you have to repair or disassemble the water

line, cut o 1/4” of the plastic tubing to make

sure you get a snug, leak-free connection.

• You can test the water line quickly using

a paper cup. Under normal conditions,

the water dispenser can ﬁll a 5.75 oz.

(170 cc) cup in about 10 seconds.

COMPLETING THE SET UP

Now that you have your new refrigerator installed

in place, you are ready to set up and enjoy the

features and functions of the appliance.

By completing the following steps, your refrigerator

should be fully operational.

1. Make sure your refrigerator is in an appropriate

location with reasonable clearance between it

and the wall. Refer to installation instructions in

this manual.

2. Once the refrigerator is plugged in, make sure

the interior light comes on when you open the

doors.

3. Set the Temperature control to the coldest

temperature and wait for an hour. The freezer

will get slightly chilled and the motor will run

smoothly. Reset the refrigerator and freezer to

the temperatures you want.

4. After you plug the refrigerator in, it will

take a few hours to reach the appropriate

temperature. You can store food and drinks

in the refrigerator after the temperature is

suciently cool.

In the event of a power failure, call the local oce

of your Electricity Company and ask how long it is

going to last.

- Most power failures that are corrected in an

hour or two will not aect your refrigerator

temperatures. However, you should minimize

the number of door openings while the

power is o.

- But Should the power failure last more than

24hours, remove all frozen food.

DA68-02601A-16.indb 14 2018. 10. 8. 오후 4:32

setting up _15

01 SETTING UP

If the key is provided with refrigerator, the keys

should be kept out of the reach of children and

not be in the vicinity of the appliance.

The appliance might not operate consistently

(possibility of defrosting of co tents or

temperature becoming too warm in the frozen

food compartment) when sited for an extended

period of time below the cold end of the range of

temperatures for which the refrigerating appliance

is designed.

Do not store food which goes bad easily at low

temperature, such as bananas, melons.

Your appliance is frost free, which means there is

no need to manually defrost your appliance, as

this will be carried out automatically.

Temperature rise during defrosting can comply

with ISO requirements. But If you want to prevent

an undue rise in the temperature of the frozen

food while defrosting the appliance, please wrap

the frozen food up in several layers of newspaper.

Any increase in temperature of frozen food during

defrosting can shorten its storage life.

Do not re-freeze frozen foods that have thawed

completely.

Install the appliance in a cool, dry room with

adequate ventilation.

Ensure that it is not exposed to direct sunlight and

never put it near a direct source of heat (radiator,

for example).

Never block any vents or grilles on the appliance.

Allow warm food to cool down before placing it in

the appliance.

Put frozen food in the refrigerator to thaw. You

can then use the low temperatures of the frozen

products to cool food in the refrigerator.

Do not keep the door of the appliance open for

too long when putting food in or taking food out.

The shorter time for which the door is open, the

less ice will form in the freezer.

Allow clearance to the right, left, back and top

when installing.

This will help reduce power consumption and

keep your energy bills lower.

• Under normal conditions a 170 cc(5.75

oz) cup can be ﬁlled in about 10

seconds.

DA68-02601A-16.indb 15 2018. 10. 8. 오후 4:32

16_ operating

Operating your French Door

Refrigerator

USING THE CONTROL PANEL

8

7

1

2

3

5

6

4

( 1 ) Energy

Saver

Hold 3 sec for

ºC ↔ ºF

Touching this button turns Energy Saver

mode on and o. When you turn Energy

Saver on, the Energy Saver icon lights.

Turn Energy Saver o and the icon

goes o. The Energy Saver function

automatically turns on when power is

supplied to the refrigerator.

If condensation or water drops appear

on the doors, turn the Energy Saver

mode o.

Touch and hold this button for 3

seconds to switch the temperature

units between °C and °F.

( 2 ) Freezer

(Hold 3 sec

for Power

Freeze)

Touch this button to set the freezer to

your desired temperature.

You can set the temperature between

-8°F and 5°F (between -23°C and

-15°C). Touch and hold this button for

3 seconds to decrease the time needed

to freeze products in the Freezer. It

can be helpful if you need to quickly

freeze easily spoiled items or if the

temperature in the freezer has warmed

dramatically (For example, if the door

was left open).

( 3 ) Ice

Type/Water

Hold 3 sec for

Filter Reset

Touch this button to select the ice or

water function. You can select water or

the types of ice(cubed/crushed ice).

Each time you press the button, the

cubed and crushed ice modes alternate

and the Cubed or Crushed ice icon

lights up, indicating your selection.

After you replace the water ﬁlter, touch

and hold this button for 3 seconds to

reset the water ﬁlter life indicator.

( 4 ) Alarm

Hold 3 sec

for Lighting

To turn the door open alarm on and o

If the door alarm is set to On, an alarm

beeps if any refrigerator door is left open

for more than three minutes. The beeping

stops when you close the door. The door

alarm function is preset to On int the

factory You can turn it o by touching and

then releasing this button. You can turn

it back on in the same fashion. The icon

lights up when the function is on.

If you touch and hold the Alarm/Lighting

button for 3 seconds, the dispenser LED

Lamp will stay on. To turn o the light

press the button for 3 seconds again.

( 5 ) Fridge

Hold 3 sec for

Power Cool

Touch this button to set the fridge to your

desired temperature. You can set the

temperature between 34°F and 44°F

(between 1°C and 7°C ). Touch and hold

this button for 3 seconds to decrease

the time needed to cool products in the

Refrigerator. It can be helpful if you need

to quickly cool easily spoiled items or if

the temperature in the fridge has warmed

dramatically (For example, if the door was

left open).

( 6 ) Ice O

Hold 3 sec for

Child Lock

If you don’t want to make more ice, touch

the Ice O button. Touching this button

for 3 seconds turns on Child Lock which

locks the display panel and dispenser

buttons so the buttons can not be used.

The Child Lock icon lights up to indicate

you’ve activated the Child Lock function.

Press 3 seconds to unlock. The Child

Lock are not going to lock the Cool

Pantry. The lights and motors start until

the refrigerator turns o again.

( 7 ) Ice O

If you don’t want to make more ice, touch

the Ice O button.

The icon will light up and the Ice-Maker

stops making ice.

We recommend you to stop ice

making if the following occur:

- There is enough ice in the ice bucket.

- You want to save water and energy.

- Water is not being supplied to

the refrigerator.

If the ice maker function is

ON, and the water Line is not

connected, there will be a water

valve noise from the back of the

unit, press the Ice O (Hold 3sec

for child lock) button for less

than 3 seconds until the Ice O

Indicator ( ) illuminates.

(RF263T**)

(RF263B/N**)

DA68-02601A-16.indb 16 2018. 10. 8. 오후 4:32

operating _17

02 OPERATING

( 8 ) Filter

Water ﬁlter usage

This icon will light up when you need

to change the ﬁlter. After you use

about 300 gallons of water, the ﬁlter

indicator lights up. (about 6 months).

The icon will blink red for several

seconds when you open or close

the door. After you install the new

water ﬁlter, reset the ﬁlter indicator by

touching the Ice Type/Water Hold 3

sec for Filter Reset button.

• If water is not dispensing or

dispensing slowly, you need to

replace the water ﬁlter because

the water ﬁlter is clogged.

• Some areas have large

amounts of lime in their water,

which causes the water ﬁlter to

clog more quickly.

Cooling O

Mode

Cooling O mode (also called Shop

mode), is designed for use by retailers

when they are displaying refrigerators

on the shop ﬂoor. In Cooling O

mode, the refrigerator’s fan motor

and lights work normally, but the

compressor does not run, and the

refrigerator and freezer do not get

cold. To start Cooling O mode, touch

and hold the Energy Saver button

and the Freezer button for 5 seconds

during normal operation.

The refrigerator chime sounds and the

temperature display ﬂashes OF OF.

To cancel Cooling O mode, touch

and hold the Energy Saver and the

Freezer buttons again for 5 seconds.

CHANGING THE WATER FILTER

To reduce risk of water damage to your

property DO NOT use generic brands

of water ﬁlters in your SAMSUNG

Refrigerator.

USE ONLY SAMSUNG BRAND WATER FILTERS.

SAMSUNG will not be legally responsible for any

damage, including, but not limited to property

damage caused by water leakage from the use of

a generic water ﬁlter. SAMSUNG Refrigerators are

designed to work ONLY WITH SAMSUNG Water

Filter.

The Filter light turns red to let you

know when it is time to change

your water ﬁlter cartridge.

To give you time to get a new ﬁlter,

the red light comes on just before

the capacity of the current ﬁlter

runs out.

(Red)

Changing the ﬁlter on time provides you with the

freshest, cleanest water from your refrigerator.

1. Shut o the water supply. Then, turn the water

ﬁlter ( 1 ) about 1/4 turn, counter-clockwise.

2. Pull the water ﬁlter ( 1 ) from the case ﬁlter ( 2 ).

WARNING

2

1

• To change the water ﬁlter more easily,

shut o the water supply valve.

• Sometimes, it is hard to disassemble the water

ﬁlter because impurities in the water cause it

to stick. If you are having diculties, grip the

water ﬁlter ﬁrmly and pull it hard.

• When you pull the

water ﬁlter, a little

water can leak from

the opening. This is

normal.

3

2

To minimize the water leaks, keep the ﬁlter

cartridge horizontal when you pull it.

• To prevent overﬂow, empty the water ﬁlter tray

( 3 ) and dry around the ﬁlter case ( 2 ).

3. Insert the new ﬁlter into the ﬁlter case ( 4 ).

4. Push the ﬁlter, and then turn it clockwise until

it locks.

• If you have trouble inserting the water

ﬁlter because of high water pressure,

shut o the water supply valve.

• The locked symbol should be lined up with the

indicator line.

4

5. Touch and “Ice Type/

Water Hold 3 sec for

Filter Reset” button

(

(Filter Reset)

) for about

3 seconds to reset the

water ﬁlter. The color

of the indicator ( )

changes from red to

light o.

6. If you turned o the water supply, turn it back on.

• For a replacement water ﬁlter, you can

visit your local home Improvement

center or contact the Samsung Parts

distributor.

• Be sure the replacement water ﬁlter has the

SAMSUNG logo on the box and on the water

ﬁlter. Link : http://www. samsungparts.com

DA68-02601A-16.indb 17 2018. 10. 8. 오후 4:32

18_ operating

Removing any residual matter inside

the water supply line after installing

the water ﬁlter.

1. Turn ON the main

water supply and

supply water to the

refrigerator.

2. Select water in the button “ICE TYPE/

WATER”,pour 1 Gal (6-7 minutes) to clean the

water supplier system and it will take the air

out from the lines.

3. If after pour 1 Gal the water doesn’t turn

clear is possible an additional ﬂushing in the

household lines.

4. Open the Refrigerator door and make sure

there are no water leaks coming from the

water ﬁlter.

• Be sure to ﬂush the dispenser system

thoroughly, otherwise water may drip

from the dispenser.

• This means that there is still air in the line.

Reverse Osmosis Water Supply

IMPORTANT :

The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet

valve of the refrigerator needs to be between 35

and 120 psi (241 and 827 kPa).

If a reverse osmosis water ﬁltration system is

connected to your cold water supply, the water

pressure to the reverse osmosis system needs to

be a minimum of 40 to 60 psi (276 to 414 kPa.) If

the water pressure to the reverse osmosis system

is less than 40 to 60 psi (276 to 414 kPa):

• Check to see whether the sediment ﬁlter in the

reverse osmosis system is blocked. Replace

the ﬁlter if necessary.

• Allow the storage tank on the reverse osmosis

system to reﬁll after heavy usage.

• If your refrigerator has a water ﬁlter, it may

further reduce the water pressure when used

in conjunction with a reverse osmosis system.

Remove the water ﬁlter.

If you have questions about your water pressure,

call a licensed, qualiﬁed plumber.

CONTROLLING THE TEMPERATURE

Basic temperature of Freezer and

Refrigerator Compartments

The basic temperature and recommended

temperatures of the Freezer and Refrigerator

Compartments are 0°F and 37°F(or -18°C and

3°C) respectively. If the temperature of the Freezer

and Refrigerator Compartments are too high or

low, adjust the temperature manually.

Controlling the Freezer temperature

Recommend Temp (Freezer) : 0 °F (or -18 °C )

The Freezer temperature can be set between -8°F

and 5°F (or between -23°C and -15°C) to suit

your particular needs. Press the Freezer button

repeatedly until the desired temperature is shown

in the temperature display. The temperature will

change by 1°F (or 1°C) with each press. See

below.

Fahrenheit : 0°F

➞

-1°F

➞

-2°F

➞

-3°F

➞

-4°F

➞

-5°F

➞

-6°F

➞

-7°F

➞

-8°F

➞

5°F

➞

4°F

➞

3°F

➞

2°F

➞

1°F

➞

0°F.

Centigrade : -18°C

➞

-19°C

➞

-20°C

➞

-21°C

➞

-22°C

➞

-23°C

➞

-15°C

➞

-16°C

➞

-17°C

➞

-18°C.

Keep in mind that foods such as ice cream may

melt at 4°F (or -15.5°C). The temperature display

will move sequentially from -8°F to 5°F (or from

-23°C to -15°C).

Controlling the fridge temperature

The fridge temperature can be set between 34 °F

and 44 °F (or between 1 °C and 7 °C) to suit

your particular needs. Press the Fridge button

repeatedly until the desired temperature is shown

in the temperature display. The temperature will

change by 1 °F (or 1 °C) with each press. See

below.

Fahrenheit : 37 °F ➞ 36 °F ➞ 35 °F ➞ 34 °F ➞

44 °F ➞ 43 °F ➞ 42 °F ➞ 41 °F ➞

40 °F ➞ 39 °F ➞ 38 °F ➞ 37 °F.

Centigrade : 3 °C ➞ 2 °C ➞ 1 °C ➞ 7 °C ➞ 6 °C

➞ 5 °C ➞ 4 °C ➞ 3 °C.

The temperature control process for the Fridge

works just like the Freezer process. Press the

DA68-02601A-16.indb 18 2018. 10. 8. 오후 4:32

operating _19

02 OPERATING

Fridge button to set your desired temperature.

After a few seconds, the Fridge will begin

adjusting towards the newly set temperature. This

will be reﬂected in the digital display.

Recommend Temp (Fridge) : 37 °F (or 3 °C )

- The temperature of the Freezer, Fridge

or Cool Select Pantry Zone may

rise when you open the doors too

frequently, or if a large amount of warm

or hot food is placed inside.

- This may cause the digital display to blink.

Once the Freezer and Fridge temperature

return to their normal set temperatures, the

blinking will stop.

- If the blinking continues, you may need to

“reset” the Refrigerator. Try unplugging the

appliance, wait for around 10 minutes and

then plug the power cord back in.

- If there is a communication error between the

Display and Main Controller, the Convertible

Display light may blink. If the blinking continues

for a long period of time, please contact a

Samsung Electronics Service Center.

USING THE COLD WATER

DISPENSER

Push the appropriate ice type button

to select what you want dispensed.

NO ICE

Select this if you want to

turn ice maker o

Using the ice Dispenser

Place a glass underneath

the ice dispenser and push

gently against the dispenser

lever with your glass.

Make sure the glass is in line

with the dispenser to prevent

the ice from bouncing out.

Please wait 2 seconds before removing

the glass under the dispenser to prevent

spills.

If the Refrigerator door opens, the

Dispenser does not work.

When Cubed Ice is selected after using

the Crushed Ice mode, a small amount of

residual crushed ice might be produced.

Do not pull the lever out. You could

damage or break the lever’s spring.

check the

water level

Test button

Maintaining the Ice Bucket

• To clean the ice bin/bucket, wash with a mild

detergent, rinse well, and dry thoroughly it. Do

not use harsh or abrasive cleaners or solvents.

• The ice cubes generated by the rapid ice

making process will look white, which indicates

they are generated normally.

• As the ice maker in the refrigerator room

makes ice cubes even faster, move the ice

cubes from the refrigerator ice bin to the

freezer ice bin if you need more ice cubes.

• If ice doesn’t come out, pull out the ice bucket

and press the test button located on the right

side of ice maker.

• Do not press the test button continuously

when the tray is ﬁlled with ice or water. Water

may overﬂow or ice may jam the bucket.

• Normal Use

To ﬁll the ice bucket to maximum capacity after

installation, follow these steps:

Water may overﬂow or ice may jam the bucket.

CAUTION

DA68-02601A-16.indb 19 2018. 10. 8. 오후 4:32

20_ operating

check the

water level

Test button

To remove the ice cubes without use the

Ice Bucket, turn o the ice maker.

(Remove the front cover of the Ice Maker)

Ice cubes in the ice machine may leak on

the drawer.

Not put food into the tray of ice.de hielo.

If you store food in the ice bucket,may

hinder the ice maker to open or close the

door, and damage the ice maker.

Note that the ice cubes from the ice

bucket can spill over the box to remove

the tray from the drawer. In this case, you

must remove the drawer the ice cubes

that have been spilled.

In case of power outage, ice cubes can

melt and then freeze when power returns,

causing the dispenser to stop working.

To prevent this from happening after a power

outage, remove the ice bucket and discard the ice

and wastewater.

• If you use all the ice at one time, repeat

Steps 2 and 3 on the previous page.

• However, wait only 8 hours before removing the

ﬁrst 4 to 6 cubes. This procedure will replace

ice cubes and ensure their maximum output.

• The ﬁrst ice should be dicarded as they

may have bad taste.

How to Use Ice O function

WARNING

When you select the O Ice (hielodesactivado),

remove all ice cube tray. If not using the ice

dispenser, it is possible to stack the cubes.

Remove the tank in the direction of the arrow.

Dispose of ice cubes or ice mass. Push the

bottom of the tray until it clicks. If the tray does

not ﬁt, turn the propeller 90 degrees and try again.

Use only the ice maker refrigerator.

Only a suitably qualiﬁed person must

install / connect the water supply to the

refrigerator. Connect only to a potable

water supply.

In order that the ice maker work properly, need a

water pressure of 20 ~ 125 psi (138 ~ 862 kPa).

Whether traveling for vacation or business and will

not use water dispensers and ice for an extended

period:

- Close the stopcock. If not, can result in water

leakage.

- Remove all food.

- Unplug the refrigerator.

- Remove excess moisture from inside the

refrigerator and leave doors open. Otherwise,

odor and mold may occur. Do not put ﬁngers,

hands or any other inappropriate object in the

container or bucket of ice maker. It may cause

personal injury or property damage.

- Never put ﬁngers or objects into the dispenser

opening. Can cause injury.

Never try to take the ice maker.

- Do not wipe or spray the ice tray with water

while in the refrigerator. Remove for cleaning.

When inserting the tray of the ice maker,

make sure it is well centrada.

De Otherwise, you could lock.

The phenomenon of turbidity

• The water entering the cooler circulates

through the main ﬁlter is a ﬁlter for

alkaline water. In the ﬁltering process,

the pressure of the water leaving

the ﬁlter increases, and the water is

saturated with oxygen and nitrogen.

When it is contacted with air, the

pressure drops rapidly and the oxygen

and nitrogen is oversaturated and

generate gas bubbles.

• Temporarily, water can have a cloudy

appearance due to these bubbles of oxygen.

After a few seconds, water is colorless.

WARNING

DA68-02601A-16.indb 20 2018. 10. 8. 오후 4:32

La page charge ...

Samsung RF263BEAESR Manuel utilisateur

Samsung RF263BEAESR Manuel utilisateur

dans d''autres langues

Documents connexes