LG STUDIO HCED3615S Guide d'installation

ENGLISH ESPAÑOL FRANÇAIS

INSTALLATION GUIDE

HOOD

Read these instructions thoroughly before installing and operating the hood.

www.lg.com

LSHD3689BD LSHD3089BD

LSHD3680ST LSHD3080ST

HCED3615S HCED3015S

MFL70208702_03

2

TABLE OF CONTENTS

3 BEFORE YOU BEGIN

4 IMPORTANT SAFETY

INSTRUCTIONS

7 PRODUCT SPECIFICATIONS

7 General Specifications

8 Dimensions

9 PRODUCT OVERVIEW

9 Parts

9 Accessories

10 PLANNING THE INSTALLATION

10 Cabinet Layout

11 Ducting Options

12 Ducting Calculation Sheet

13 Power Supply

13 Verify the Package Contents

14 INSTALLATION INSTRUCTIONS

14 Mounting the Range Hood

15 WIRING DIAGRAM

3

BEFORE YOU BEGIN

ENGLISH

BEFORE YOU BEGIN

IMPORTANT:

•

Installer: In the interest of safety and to minimize problems, read these installation

instructions completely and carefully before you begin the installation process. Leave

these installation instructions with the customer.

•

Customer: Keep these installation instructions for future reference and the local electrical

inspector’s use.

APPLIANCE DATA PLATE

•

The appliance data plate contains the model and serial number information and the

electrical requirements.

•

It is located inside the hood behind the filters on the back side of the chassis.

Remove the filters to view it.

All specifications subject to change without notice. LG assumes no liability for

changes to specifications.

4

IMPORTANT SAFETY INSTRUCTIONS

Read and follow all instructions when using the range to prevent the risk of fire, electric

shock, personal injury, or damage. This guide does not cover all possible conditions that

may occur. Always contact your service agent or manufacturer about problems that you do

not understand.

Download this owner's manual at: http://www.lg.com

This is the safety alert symbol. This symbol alerts you to potential hazards that

can result in property damage and/or serious bodily harm or death.

All safety messages will follow the safety alert symbol and either the word

WARNING or CAUTION. These words mean:

WARNING

- Indicates a hazardous situation which, if not avoided, could result

in death or serious injury.

CAUTION

- Indicates a hazardous situation which, if not avoided, could result

in minor or moderate injury.

WARNING

•

To avoid the possibility of explosion or fire, do not store or use combustible, flammable

or explosive vapors and liquids (such as gasoline) inside or in the vicinity of this or

any other appliance. Also keep items that could explode, such as aerosol cans away

from cooktop burners, ovens and range hoods. Do not store flammable or explosive

materials in adjacent cabinets or areas.

•

If the information in this manual is not followed exactly, a fire or explosion may result

causing property damage, personal injury or death.

•

Do not use an additional speed control device with this unit.

•

To avoid motor bearing damage and noisy and/or unbalanced impellers, keep

drywall spray, construction dust, etc. off power unit.

•

Your ventilator motor has a thermal overload which will automatically shut off

the motor if it becomes overheated. The motor will restart when it cools down. If

the motor continues to shut off and restart, have the product serviced.

•

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

– Use this unit only in the manner intended by the manufacturer. If you have questions,

contact the manufacturer.

– Before servicing or cleaning unit, switch power off at service panel and lock the

electrical panel door to prevent power from being switched on accidentally. When the

electrical panel door cannot be locked, securely fasten a prominent warning device,

such as a tag, to the service panel.

5

IMPORTANT SAFETY INSTRUCTIONS

ENGLISH

WARNING

•

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,

OBSERVE THE FOLLOWING:

– Installation work and electrical wiring must be done by qualified person(s) in

accordance with all applicable codes and standards, including fire-rated construction.

– Sufficient air is needed for proper combustion and exhausting of gases through the

flue(chimney) of fuel burning equipment to prevent back drafting. Follow the heating

equipment manufacturer’s guidelines and safety standards such as those published

by the National Fire Protection Association (NFPA), and the American Society for

Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code

authorities.

– When cutting or drilling into wall or ceiling, do not damage electrical wiring and other

hidden utilities.

– Ducted fans must always be vented to the outdoors.

CAUTION

For general ventilating use only. Do not use to exhaust hazardous or explosive materials

and vapors.

GENERAL SAFETY PRECAUTIONS

To reduce the risk of fire, electric shock, serious injury or death when using the appliance,

follow basic safety precautions, including the following:

WARNING

•

Do not install or operate this hood if it has been damaged, dropped, has damaged

electrical wires or is not working properly. If the product is damaged when received,

immediately contact the dealer or builder.

•

This range hood must be installed and grounded by a qualified installer according to

these installation instructions.

•

Install or locate this appliance only in accordance with these installation instructions

and the requirements specified by the manufacturer of the cooktop or range. Improper

installation, adjustment, alteration, service or maintenance can cause serious personal

injury or property damage.

•

The customer should not install, repair or replace any part of the range hood unless

specifically recommended in the literature accompanying it. A qualified service

technician should perform all other service.

•

Keep all packaging materials away from children. Plastic bags can cause suffocation.

•

Do not use an extension cord or adapter plug with this appliance.

•

The installer must show the customer the location of the fuse box or circuit breaker

panel box so that the customer knows where and how to turn the power off.

•

Before installing or servicing the range hood, switch power off at the fuse box circuit

breaker and lock the electrical panel door to prevent power from being switched on

accidentally. When the electrical panel cannot be locked, securely fasten a prominent

warning device, such as a tag, to the electrical panel.

•

Read the owner's manual completely before using the appliance. Clean the appliance

only as instructed in the owner's manual. Use only the cleaners specified.

•

Do not tamper with the controls.

6

IMPORTANT SAFETY INSTRUCTIONS

WARNING

•

Never allow the filter(s) to become blocked or clogged. Do not allow foreign objects,

such as cigarettes or napkins, to be sucked into the hood.

•

Clean the filter(s) and all grease-laden surfaces often to prevent grease fires and

maintain performance.

•

If the cooktop and range hood are near a window, use an appropriate window

treatment. Avoid long drapes or other window coverings that could blow over the

cooktop and hood, resulting in a fire hazard.

•

Always run the fan(s) whenever the cooktop is operating.

•

Never leave the range or cooktop unattended when a burner (or element) is in use.

Boil-overs and greasy spills may smoke and/or ignite.

•

Do not leave children alone or unattended in the area where the cooktop and range

hood are in use. Never allow children to sit or stand on an appliance. Do not let children

play with a range, cooktop or range hood. Do not store items of interest to children

above or around the cooktop, range or range hood.

•

The minimum vertical distance between the cooktop surface and the exterior part of

the hood must be no less than 26" (66 cm). The vertical distance required may be

longer for the range or cooktop being used. Consult the range or cooktop installation

instructions for the minimum and maximum vertical distance from the appliance being

used.

•

TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCT WORK.

READ AND SAVE THESE INSTRUCTIONS

7

PRODUCT SPECIFICATIONS

ENGLISH

PRODUCT SPECIFICATIONS

General Specifications

All Models

Fan Speeds 5

Filters Aluminum mesh filters

Total Connect Load 120 VAC, 60 Hz, 4 Amp.

Lights 120 VAC, 8 W LED light strip

Model Specic

Model Number

LSHD3689BD, LSHD3680ST, HCED3615S, LSHD3089BD,

LSHD3080ST, HCED3015S

Filters 2

Weight Specications

Model Number Weight

LSHD3689BD, LSHD3680ST,

HCED3615S

37 lb. (17 kg)

LSHD3089BD, LSHD3080ST,

HCED3015S

35 lb. (16 kg)

8

PRODUCT SPECIFICATIONS

Dimensions

Tolerances: +1/16", -0 (1.6 mm, -0), unless otherwise stated.

NOTE

The exhaust duct(s) and electrical wiring can be connected from either the top or the back of the hood.

10

3/8

″

1

3/16

″

29 15/16″, 35 7/16″

10

5/8″

22

1/16″

5 5/16″

4"

1"

6

"

STANDARD

min. ducted - 27″

min. recirc. - 31″

max. - 48″

18 7/16″

Overall Dimensions

A

C

B

Model A B C

LSHD3689BD,

LSHD3680ST,

HCED3615S

36" 26

15

/

16

" 22

1

/

16

"

LSHD3089BD,

LSHD3080ST,

HCED3015S

30" 26

15

/

16

" 22

1

/

16

"

9

PRODUCT OVERVIEW

ENGLISH

PRODUCT OVERVIEW

Parts

1

4 5

23

Accessories

Included Accessories

Manual

Duct cover bracket Duct cover Manual M6 x 1" (3)

M6 x 1-1/2" (2) M4 x 8 (2) Wire Caps (3)

1

Hood

2

Icon Touch Control Panel

3

LED Strip Light

4

Mesh Filter

5

Side Panel

(Only for LSHD3689BD, LSHD3680ST,

HCED3615S)

10

PLANNING THE INSTALLATION

PLANNING THE

INSTALLATION

WARNING

Observe all governing codes and ordinances

during planning and installation. Contact your

local building department for further information.

Use only duct work deemed acceptable by state,

municipal and local codes.

Cabinet Layout

WARNING

To reduce the risk of personal injury caused by

reaching over a hot appliance, cabinet storage

space located directly above the range should be

avoided.

26″ min.

34

″

max.

minimum ducted (D)

minimum recirculating (E)

maximum (F)

36

″

minimum ducted (A)

minimum recirculating (B

)

maximum (C)

Minimum Cabinet Width

Standard

Duct Cover

Hood

Heights

minimum ducted (A) 27"

minimum recirculating (B) 31"

maximum (C) 48-1/2"

Ceiling

Heights

minimum ducted (D) 89" (7' 5")

minimum recirculating (E) 93" (7' 9")

maximum (F) 118" (9' 10")

Ducting

A minimum of 6″ round duct must be used to maintain

maximum air flow efficiency.

Always use rigid metal ducts only. Flexible ducts

could restrict air flow by up to 50%.

Also use calculation (on page 12) to compute total

available duct run when using elbows, transitions and

caps.

ALWAYS, when possible, reduce the number of

transitions and turns. If long duct run is required,

increase duct size from 6″ to 7″ or 8″.

If turns or transitions are required, install as far away

from hood duct output and as far apart as possible.

Minimum mount height between range top to hood

bottom should be no less than 26″.

Maximum mount height should be no higher than 34″.

It is important to install the hood at the proper

mounting height. Mounting the hood too low could

result in heat damage and fire hazard. Mounting the

hood too high will make it hard to reach and reduce

its performance and efficiency.

If available, also refer to the range manufacturer’s

height clearance requirements and recommended

hood mounting height above range.

CAUTION

DAMAGE DURING SHIPPING / INSTALLATION:

•

Please fully inspect unit for damage before

installation.

•

If the unit is damaged in shipment, return the

unit to the store in which it was bought for

repair or replacement.

•

If the unit is damaged by the customer, repair

or replacement is the responsibility of the

customer.

•

If the unit is damaged by the installer (if other

than the customer), repair or replacement must

be made by arrangement between customer

and installer.

11

PLANNING THE INSTALLATION

ENGLISH

Ducting Options

WARNING

Fire Hazard

•

NEVER exhaust air or terminate duct work into

spaces between walls, crawl spaces, ceiling,

attics or garages.

•

All exhaust must be ducted to the outside.

•

Use metal ductwork only.

•

Fasten all connections with sheet metal screws

and tape all joints with certified Silver Tape or

Duct Tape.

Sample Ducting Options

Roof Pitch w/

Flashing & Cap

(blower

housing)

ductless

recirculating

(blower

housing)

side wall cap

w/ gravity damper

Soft or crawl space

(blower

housing)

side wall cap

w/ gravity damper

(blower

housing)

12

PLANNING THE INSTALLATION

Ducting Calculation Sheet

Duct pieces

Equivalent

length x number

used =

Total

3-1/4" x 10"

Rect.,

straight

1 Ft. x ( ) = Ft.

6" Round,

straight

1 Ft. x ( ) = Ft.

7"-10"

Round,

straight

1 Ft. x ( ) = Ft.

3-1/4" x 10"

Rect.90˚

elbow

15 Ft. x ( ) = Ft.

3-1/4" x 10"

Rect.45˚

elbow

9 Ft. x ( ) = Ft.

3-1/4" x 10"

Rect.90˚

at elbow

24 Ft. x ( ) = Ft.

3-1/4" x 10"

Rect.

wall cap

with damper

30 Ft. x ( ) = Ft.

3-1/4" x 10"

Rect.to

6" round

transition

5 Ft. x ( ) = Ft.

3-1/4" x 10"

Rect.to

6" round

transition

90˚ elbow

20 Ft. x ( ) = Ft.

6" Round,

90˚ elbow

15 Ft. x ( ) = Ft.

6" Round,

45˚ elbow

9 Ft. x ( ) = Ft.

Subtotal column 1 = Ft.

Duct pieces

Equivalent

length x number

used =

Total

6" Round

wall cap

with damper

30 Ft. x ( ) = Ft.

6" Round,

roof cap

30 Ft. x ( ) = Ft.

6" round to

3-1/4" x 10"

rect.

transition

1 Ft. x ( ) = Ft.

6" round to

3-1/4" x 10"

rect.

transition

90˚ elbow

16 Ft. x ( ) = Ft.

7" - 10"

Round,

90˚ elbow

15 Ft. x ( ) = Ft.

7" - 10"

Round,

45˚ elbow

9 Ft. x ( ) = Ft.

7" - 10"

Round wall

cap with

damper

30 Ft. x ( ) = Ft.

7" - 10"

Round,

roof cap

30 Ft. x ( ) = Ft.

7" round to

3-1/4" x 10"

rect.

transition

8 Ft. x ( ) = Ft.

7" round to

3-1/4" x 10"

rect.

transition

90˚ elbow

23 Ft. x ( ) = Ft.

Subtotal column 2 = Ft.

Subtotal column 1 = Ft.

Total ductwork = Ft.

Maximum Duct Length: For satisfactory air

movement, the total duct length should not exceed

100 equivalent feet.

13

PLANNING THE INSTALLATION

ENGLISH

Ductwork Design Tips

Wherever possible, reduce the number of transitions

and turns to as few sharp angles as possible. Two

staggered 45° angles are better than one 90°.

Keep turns as far away from the hood exhaust as

possible, and allow as much space between bends

as possible.

For best performance, use round ducts instead of

rectangular, especially when elbows are required.

If multiple elbows are used, try to keep a minimum of

24" of straight duct between them.

Avoid “S” or “back to back” use of adjacent elbows.

In regions where the weather gets extremely cold,

use thermal breaks, such as a short section of non-

metallic duct, to avoid indoor heat loss. Locate the

break as close as possible to the outside pass-

through point.

Do not use flexible metal duct.

Do not use ductwork that is smaller in cross-sectional

area than the recommended types above.

Power Supply

WARNING

•

The information in this manual should be

followed exactly. Failure to do so could result

in fire or electrical shock, causing property

damage, personal injury or death.

•

All electrical work must by performed by

qualified electrician or person with similar

technical knowledge and background.

•

For personal safety, remove house fuse or open

circuit breaker before beginning installation. Do

not use extension cord or adapter plug with this

appliance.

•

Follow national electrical codes or

prevailing local codes and ordinances.

Electrical Supply

This appliance requires a 120V 60Hz electrical

supply, and must be connected to an individual,

properly grounded branch circuit, protected by a 15 or

20 ampere circuit breaker or time delay fuse. Wiring

must be 2 wire w/ ground. Please also refer to the

Electrical Diagram label on product.

GREEN

WHITE

BLACK

GREEN

Wire cap,

3 places

Junction box

To house circuit breaker

panel or fuse box

UL/CSA approved

NEMA strain relief

To range hood

3 Wire Connection to Junction Box

Cable Lock

A cable locking connector (not supplied) might

also be required by local codes. Check with local

requirements and codes, and purchase and install

appropriate connector if necessary.

Cable Lock

Verify the Package Contents

Unpack the parts box and verify that all parts and

accessories have been included. If any item is

missing or damaged, please contact the dealer

immediately. Do not install a damaged or incomplete

appliance.

Make sure you have everything necessary for proper

installation before proceeding.

14

INSTALLATION INSTRUCTIONS

INSTALLATION

INSTRUCTIONS

WARNING

•

Do not install the range hood unless the

electrical service provided meets the range

hood specifications.

•

Observe all governing codes and ordinances

during installation. Contact your local building

department for further information.

•

A qualified technician must complete the

installation of this built-in appliance. More than

one person is required to raise the hood into

place. The owner is responsible to make sure

the hood is properly installed.

Mounting the Range Hood

Mounting Under a Kitchen Cabinet

CAUTION

At least two installers are required due to the

weight and size of the hood.

1

Measure from range top to desired hood

bottom and mark line A. (26" minimum from

range top).

2

Plumb and mark center line.

3

Mark hood height line B. (18-7/16" from line A)

4

Mark mounting spread from center line. (8-7/8"

on line B)

5

Fasten (2) M4 x 1-1/2" screws into studs on

line B but do not tighten all the way.

NOTE

Wood blocking may need to be added behind

the drywall if no studs are present. Wall anchors

may also be used but check local codes for

compliance. Failure to use suitable wall anchors

and screws to hold the weight of the hood could

result in personal injury or damage to cooking

surface or counter.

6

Remove the (2) aluminum mesh filters.

7

Hang hood onto the mounting screws and hand

tighten each screw. (Fig A1) Secure a third M4

x 1-1/2" screw through inside of hood into wall

for extra support (Fig A2)

8

Center and attach duct cover mounting bracket

to wall just below the ceiling or soffit using (2)

M4 x 1" screws.

9

Install electrical and duct work. Seal duct work

with aluminum duct tape

10

Power up hood and check for leaks around

duct tape.

11

Place telescopic duct covers onto hood and

extend inner (top) duct cover upwards and

secure to duct cover bracket using (2) M4 x 8

screws. Reinstall mesh filters.

•

If using hood in recirculating mode you must secure

the air diverter plate onto wall before installing duct

work and duct covers. You will also need to install

charcoal filters and brackets.

A

B

Duct Cover Bracket

Brackets are

pre-installed

Fig. A1

Fig. A2

8-7/8"

18-7/16"

26" min

Center line

15

WIRING DIAGRAM

ENGLISH

WIRING DIAGRAM

Models Volts HZ MAX Amps

LSHD3089BD

LSHD3080ST

HCED3015S

LSHD3689BD

LSHD3680ST

HCED3615S

120 60 4

16

MEMO

ESPAÑOL

GUÍA DE INSTALACIÓN

CAMPANA

Lea atentamente estas instrucciones antes de instalar y poner la

campana en funcionamiento.

www.lg.com

LSHD3689BD LSHD3089BD

LSHD3680ST LSHD3080ST

HCED3615S HCED3015S

MFL70208702_03

2

ÍNDICE

3 ANTES DE COMENZAR

4 INSTRUCCIONES IMPORTANTES DE

SEGURIDAD

7 ESPECIFICACIONES DEL PRODUCTO

7 Especificaciones generales

8 Dimensiones

9 DESCRIPCIÓN GENERAL DEL

PRODUCTO

9 Piezas

9 Lista de piezas

10 PLANIFICACIÓN DE LA INSTALACIÓN

10 Disposición de alacenas

11 Opciones de conducto

12 Hoja de cálculo de conducto

13 Suministro de energía

13 Verifique el contenido del embalaje

14 INSTRUCCIONES DE INSTALACIÓN

14 Montaje de la campana extractora

15 DIAGRAMA DE CABLEADO

3

ANTES DE COMENZAR

ESPAÑOL

ANTES DE COMENZAR

IMPORTANTE:

•

Instalador: Para preservar la seguridad y reducir los posibles problemas, lea estas instrucciones

para la instalación por completo antes de comenzar el proceso de instalación. Deje estas

instrucciones al cliente.

•

Cliente: Conserve estas instrucciones de instalación para referencia futura y para que las consulte

el inspector

PLACA DE DATOS DEL ARTEFACTO

•

La placa de datos de este artefacto contiene información del número de serie y el modelo, y los

requisitos eléctricos.

•

Se encuentra ubicada dentro de la campana, detrás de los filtros, en la parte posterior del chasis.

Retire los filtros para verla.

Todas las especificaciones están sujetas a cambios sin previo aviso. LG no se hace

responsable por cambios en las especificaciones.

4

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

INSTRUCCIONES IMPORTANTES DE

SEGURIDAD

Lea y siga todas las instrucciones cuando utilice la cocina para evitar riesgos de incendios, descargas

eléctricas, lesiones personales o daños. Esta guía no incluye todas las situaciones posibles que

podrían ocurrir. Siempre comuníquese con su agente de servicio técnico o con el fabricante cuando

haya problemas que no comprenda.

Descargue este manual en: http://www.lg.com

Este es el símbolo de alerta de seguridad. Este símbolo le advierte sobre posibles riesgos

que pueden ocasionar daños materiales, lesiones personales graves o la muerte.

El símbolo de alerta de seguridad siempre estará acompañado de las palabras

"ADVERTENCIA" o "PRECAUCIÓN". Estos términos significan lo siguiente:

ADVERTENCIA

- Indica una situación peligrosa que, de no evitarse, podría

causar lesiones graves o la muerte.

PRECAUCIÓN

- Indica una situación peligrosa que, de no evitarse, podría

causar lesiones leves o moderadas.

ADVERTENCIA

•

Para evitar que se produzcan explosiones o incendios, no almacene ni use líquidos o vapores

combustibles, inflamables o explosivos (como por ejemplo, gasolina) dentro o cerca de este o

cualquier otro artefacto. Además, mantenga cualquier artículo que pueda explotar, como, por

ejemplo, latas de aerosol, alejado de los quemadores de la cocina, del horno y de la campana

extractora. No almacene materiales explosivos o inflamables en áreas o alacenas cercanas.

•

Si no sigue con exactitud la información de este manual, podrían producirse un incendio o

descarga eléctrica, daños a la propiedad, lesiones personales o la muerte.

•

No utilice un dispositivo adicional de control de velocidad con esta unidad.

•

Para evitar daños en los rodamientos del motor y rotores ruidosos y/o desequilibrados,

mantenga la unidad de potencia alejada de polvo de construcción, de yeso, etc.

•

El motor del ventilador cuenta con una protección de sobrecarga térmica que apagará

automáticamente el motor en caso de que este se sobrecaliente. El motor volverá a

arrancar cuando se enfríe. Si el motor continúa apagándose y reiniciándose, se le debe

realizar mantenimiento al producto.

•

PARA REDUCIR EL RIESGO DE INCENDIO, DESCARGAS ELÉCTRICAS O LESIONES

PERSONALES, TENGA EN CUENTA LO SIGUIENTE:

– Use esta unidad solamente del modo previsto por el fabricante. Si tiene alguna pregunta,

póngase en contacto con el fabricante.

– Antes de limpiar o realizarle mantenimiento a la unidad, apáguela desde el panel de servicio

y bloquee la puerta del panel eléctrico para evitar que la unidad se encienda por accidente.

En caso de que la puerta del panel eléctrico no se pueda bloquear, coloque un dispositivo de

advertencia bien visible y firmemente sujeto, como, por ejemplo, una etiqueta, en el panel de

servicio.

La page charge ...

LG STUDIO HCED3615S Guide d'installation

Ce manuel convient également à

LG STUDIO HCED3615S Guide d'installation

dans d''autres langues

Documents connexes

Autres documents