Jenn-Air JDB8200AWP3 Guide d'installation

JENN-AIR°

INSTALLATIONINSTRUCTIONS

UNDERCOUNTERDISHWASHER

INSTRUCTIONSD'INSTALLATION

LAVE-VAISSELLESOUSPLANDETRAVAIL

Table of Contents .............................................................. 2

Table des matieres .......................................................... 28

W10501738B

TABLEOF CONTENTS

DISHWASHER SAFETY ............................................................................... 2

INSTALLATION REQUIREMENTS ............................................................. 3

Tools and Parts ......................................................................................... 3

Location Requirements ............................................................................. 4

Drain Requirements .................................................................................. 6

Water Supply Requirements ..................................................................... 6

Electrical Requirements ............................................................................ 6

INSTALLATION INSTRUCTIONS ............................................................... 7

Prepare Cabinet Opening--Existing Utilities ............................................ 7

Prepare Cabinet Opening--New Utilities ................................................. 7

Prepare and Route Water Line ................................................................. 8

Install Drain Hose ...................................................................................... 9

Install Moisture Barrier (under a wood countertop) ................................ 11

Prepare Dishwasher ................................................................................ 11

Make Power Supply Cord Connection ................................................... 12

Determine Cabinet Opening ................................................................... 14

INSTALLATION INSTRUCTIONS (CONT.)

Install Door Handle ................................................................................. 15

Custom Panel Dimensions ..................................................................... 15

Install Custom Panel ............................................................................... 15

Choose Attachment Option .................................................................... 18

Prepare Water Supply Line..................................................................... 19

Move Dishwasher Close to Cabinet Opening ........................................ 19

Connect to Water Supply ....................................................................... 21

Connect to Drain ..................................................................................... 22

Make Direct Wire Electrical Connection ................................................. 22

Secure Dishwasher in Cabinet Opening ................................................ 24

Bottom Sound Pad Installation .............................................................. 25

Complete Installation .............................................................................. 25

Check Operation ..................................................................................... 27

If Dishwasher Does Not Operate ............................................................ 27

Additional Tips ........................................................................................ 27

DISHWASHERSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Doing so can result in serious injury or cuts.

You Need to:

• Slowly open dishwasher door while someone grasps the rear

of the dishwasher. Remove shipping materials, drain hose and

lower rack. Close dishwasher door until latched.

• Observe all governing codes and ordinances.

• Install this dishwasher as specified in these instructions.

• Installation should be performed by a qualified service

technician. The dishwasher must be installed to meet all

electrical and plumbing national and local codes and

ordinances.

Care shall be exercised when the appliance is installed or

removed, to reduce the likelihood of damage to the power-supply

cord.

WARNING: To reduce the risk of electric shock, fire, or injury to

persons, the installer must ensure that the dishwasher is

completely enclosed at the time of installation.

2

INSTALLATIONREQUIREMENTS

Gather the recommended tools and parts before starting

installation. Read and follow the instructions provided with any

tools listed here.

All Installations

Toolsneeded:

iiier Flat.blade

s I screwdriver

%e, and 1/4'! _ UL Listed/CSA

nutdr versor Approvedtwist:on

hex SoCkets Wire connectors*

10" adjustable wrench __._ %. 0Ben-end

that0pens to /_/ wiLn'L_. _/_/

1 _ L;H

1Y8! (2,9 cm)

*Must be the proper size to connect your household wiring to

16-gauge wiring in dishwasher.

Other useful items you may need:

Flashlight ._"_)Bath towel.......

Parts supplied:

Drainh0se__ i ,_

Drainhose #1ox y2

clamps (2) _ Phillips"

(1 large and head

s°rews I

; ;

UnderC0unter

mounting

brackets (2)

Parts needed:

_X ¾" hose fittin

P g

For part or kit, see local

reta!ler or call Whirlpool

Parts: 1.800,442-9991. Part

Number W10273460

sUstom

:ape (2)

f

4 #10 x 1/2"wood screws (if installing custom front panels)

®

1"TORX is a registered trademark of Saturn Fasteners, Inc.

Supplied in Kit:

4 Plastic studs (attached to each other by runners)

4 Short screws (10-16 hex head screw)

4 Long screws (8-18 Torx®head screws)

1 Template (located inside Use and Care Guide bag assembly)

1 Instruction sheet (located inside Use and Care Guide bag

assembly)

NOTE: The screws supplied are used for only 3/4"thick wooden

panel. If the wooden panel is less than 3/4"thick, customer must

purchase screws locally.

Other parts you may also need:

11/2"-2" I Mask!ng or Moisture

(3,8!-5 cm)/_._,

Screw4ype _ l(Part Number r/_/ I

4396277) _l

NOTES:

• Moisture barrier tape is recommended when installing a

dishwasher under a wood countertop.

Parts available for purchase in plumbing supply stores. Check

local codes. Check existing electrical supply. See "Electrical

Requirements" section. It is recommended that electrical

connections be made by a licensed electrical installer.

In addition, for first-time installations

Toolsneeded:

C0rdless drill

".L 1/, 3/.

wl[n V2 ,, ?4

and 11/2" ht

Saw bits

Parts needed:

CopPer tUbing(3/8"

O.D.Suggested)or

flexible braided

water supply line

See "Electrical Requirements" section:

For Direct Wire: For POwer Supply

Usel I.[ r !d, Cord:useUL

CSA}!i i ( ie Listed/CSA

strain relief

tOflt_"7 ,(2:2cm

hole marked i

dishwasher

Additional parts supplied with top-venting models only:

2#8 X 1_ Torx T15 screws 4 #10 x y8 hex-head screws

Additional parts supplied with certain models only

_ound pad

! (located in loWer rack)

Make sure all these parts are included in the literature package.

If parts are not included, call 1-800-688-1100.

Groundedelectricalsupplyrequired.

Donotrundrainlines,waterlinesorelectricalwiringwherethey

caninterferewithorcontactdishwashermotororlegs.

Thelocationwherethedishwasherwillbeinstalledmustprovide

clearancebetweenmotorandflooring.Motorshouldnottouch

thefloor.

Donotinstalldishwasherovercarpetedflooring.

Shelterdishwasherandwaterlinesleadingtodishwasheragainst

freezing.Damagefromfreezingisnotcoveredbythewarranty.

Asidepanelkitisavailablefromyourdealerforinstallingyour

dishwasherattheendofyourcabinetry.

Amoisturebarrieraccessory(PartNumber4396277)isavailable

fromyourdealerforinstallingunderneaththecountertop.

Call1-800-688-1100toorder.

l_OC@_fO_q,_ss _,__ s_,s_s__i_,,,

Check location where dishwasher will be installed. The location

must provide:

• easy access to water, electricity and drain.

• convenient access for loading and unloading dishes.

Corner locations require a 2" (5.1 cm) minimum clearance

between the side of the dishwasher door and the wall or

cabinet.

• square opening for proper operation and appearance.

• cabinet front perpendicular to floor.

• level floor. (If floor at front of opening is not level with floor

at rear of opening, shims may be needed to level

dishwasher.)

Helpful Tip: Be sure to accurately measure dimensions and

ensure dishwasher is level if the floor in the dishwasher opening is

uneven (example: Flooring extends only partway into opening).

NOTE: To avoid shifting during dishwasher operation, shims must

be securely attached to the floor.

If dishwasher will be left unused for a period of time or in a

location where it may be subject to freezing, have it winterized by

authorized service personnel.

Make sure pipes, wires and drain hose are within the shaded area

shown in the "Product and Cabinet Opening Dimensions" section.

B. For Euro handle, depth is 261/2" (67.2 cm).

For Classic handle, depth is 267/8" (67 cm).

For Pro-Style®handle, depth is 271/2 (66.8 cm).

A. Insulation may be compressed

(not used on all moaels).

31/2" . 41/4" /

(8.8 cm -10.6 cm)

/

For 4" (10 cm )toe

kick, height of cabinet

opening is 341/2`' (86.3 cm)

NOTE: Shaded areas of cabinet walls show where

utility connections may be instalJed.

C. Measured from the lowest point on the

underside of countertep. May be reduced to

7

33%" (86 cm) by removing wheels from dishwasher.

or to 33 3/4" (85.7 cm) by removing wheels and

perforated section in insulation blanket.

D. Minimum, measured from narrowest point of opening.

Check that all surfaces have no protrusions

that would prohibit dishwasher installation.

A new drain hose is supplied with your dishwasher. If drain

hose is not long enough, use a new drain hose with a

maximum length of 12 ft (3.7 m) (Part Number 3385556) that

meets all current AHAM/IAPMO test standards, is resistant to

heat and detergent, and fits the 1" (2.5 cm) drain connector of

the dishwasher.

Make sure to connect drain hose to waste tee or disposer inlet

above drain trap in house plumbing and 20" (50.8 cm)

minimum above the floor. It is recommended that the drain

hose either be looped up and securely fastened to the

underside of the counter, or be connected to an air gap.

Make sure to use an air gap if the drain hose is connected to

house plumbing lower than 20" (50.8 cm) above subfloor or

floor.

Use 1/2"minimum I.D. drain line fittings.

If required, the air gap should be installed in accordance with

the air gap installation instructions. When you are connecting

the air gap, a rubber hose (not provided) will be needed to

connect to the waste tee or disposer inlet.

Vk:se ,£pp) y !equ ements

A hot water line with 20 to 120 psi (188 to 862 kPa) water

pressure can be verified by a licensed plumber.

120°F (49°C) water at dishwasher.

3/8"O.D. copper tubing with compression fitting or flexible

braided water supply line (Part Number 4396897RP).

NOTE: 1/2"minimum plastic tubing is not recommended.

A 90° elbow with 3/4"hose connection with rubber washer.

Do not solder within 6" (15.2 cm) of the water inlet valve.

Be sure that the electrical connection and wire size are adequate

and in conformance with the National Electrical Code, ANSI/NFPA

70 - latest edition and all local codes and ordinances.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

You must have:

• 120-volt, 60 Hz, AC-only, 15- or 20-amp, fused electrical

supply.

• Copper wire only.

We recommend:

• A time-delay fuse or circuit breaker.

• Aseparate circuit.

If connecting dishwasher with a

power supply cord:

Use UL Listed power supply cord kit _--

(Part Number 4317824) marked for

use with dishwasher.

Power supply cord must plug into a grounded

3 prong outlet, located in the cabinet next to

the dishwasher opening. Outlet must meet all

local codes and ordinances.

If connecting dishwasher with direct wiring:

• Use flexible, armored or nonmetallic

sheathed, copper wire with

grounding wire that meets the

wiring requirements for your home

and local codes and ordinances.

• Use a UL Listed/CSA Approved strain relief.

6

INSTALLATIONINSTRUCTIONS

Electrical Shock Hazard

Disconnect electrical power at the fuse box or circuit

breaker box before installing dishwasher.

Failure to do so can result in death or electrical shock.

[ Disc0ineCt electrical p0we[ at the fUSe box 0r CirCUit

J

JDo already have utility

you

hookups?

YeS _F01[ow inStructionsi!n the"Prepare cabinet

OpeningmExisting utilities section:

No _Fol[ow instructi0ns inthe ,,Piepare cabinet

Open!ng_aew util!ties" seCt!0n:

if the water line and the cable extend to the locations shown,

proceed to the "Install Drain Hose" section. If they do not reach far

enough, follow the instructions in the "Prepare Cabinet Opening--

New Utilities" section.

Prepare and route the electrical supply

Option A, Power Supply Cord:

NOTE: A grounded 3 prong outlet is required inside a cabinet next

to the dishwasher cabinet opening.

Drill a 1W' (3.8 cm) hole in cabinet side or rear.

See "Product and Cabinet Opening Dimensions" section.

Woodcabinet:Sandtheholeuntilsmooth.

Metalcabinet:Coverholewithgrommetincludedwithpower

supplycordkit.

Option B, Direct Wire:

Helpful Tip: Wiring the dishwasher will be easier if you route the

cable into the cabinet opening from the right-hand side.

Drill a 1V2"(3.8 cm) hole in right-hand cabinet side or rear.

See "Product and Cabinet Opening Dimensions" section.

Wood cabinet: Sand the hole until smooth.

Metal cabinet: Cover hole with grommet (Part Number 302797 -

not provided).

Direct Wire-Route cable

Route cable from power supply through cabinet hole (cable must

extend to the right front side of cabinet opening). Tape cable to

the floor in area shown. This will prohibit cable from moving when

dishwasher is moved into cabinet opening.

Helpful Tip: Routing the water line through the left side of cabinet

opening will make water connection easier.

Drill a V2"(1.3 cm) hole in the cabinet side or rear.

2-1 Measure water supply line"}

(copper tubing only)

Measure overall length of copper tubing for the water supply line.

8

Attach the water supply line (copper tubing or flexible braided line)

to the hot water line using a connection configuration that is in

compliance with local codes and ordinances. The water supply to

the dishwasher should have a manual shutoff valve located under

the sink.

Slowly route water supply line through hole in cabinet. (If you are

using copper tubing, it will bend and kink easily, so be gentle.) It

should be far enough into the cabinet opening to connect it to the

dishwasher inlet on the front left side of the dishwasher.

Slowly turn water shutoff valve to "ON" position. Flush water into

a shallow pan until clear to get rid of particles that could clog the

inlet valve. Turn shutoff valve to "OFF" position.

Route water line and tape it to the floor in area shown. This will

keep it from moving when dishwasher is moved into cabinet

opening.

D cs Hose

IMPORTANT: Always use a new drain hose. Check local codes to

determine whether an air gap is required.

If needed, drill a 1Y2"(3.8 cm) diameter hole in cabinet wall or side

of the opening closest to the sink.

Route drain hose as shown through hole in cabinet to the front

center of opening where drain connection will be made. Tape

drain hose to the floor in area shown. This will prohibit it from

moving when dishwasher is moved into cabinet opening.

Connectdrainhosetowasteteeorwastedisposer

us!ngoneofthefollowingoptions:

*OptionB,Nowastedisposer-noa!rgap

*' OptiOn C, Waste disposer _with ai[ gap

; Option D, No waste disp0ser_w th air gap

IMPORTANT: The drain hose connection of the disposer or a

waste tee must be made before the drain trap and at least

20" (50.8 cm) above the floor where the dishwasher will be

installed.

Helpful Tip: To reduce vibration of the hose, keep the hose away

from the floor.

Option A, Waste disposer - no air gap

1. Using a hammer and screwdriver,

knock plug into disposer.

2. Use needle-nose pliers to remove

plug.

3.

Attach drain hose to disposer inlet

with large drain hose clamp

(provided). Use pliers to squeeze

clamp open and move into position.

Option B, No waste disposer - no air gap

1. Fit rubber end of drain hose to waste

tee and cut if needed.

NOTE: Do not cut ribbed section.

2. Attach rubber end of drain hose to

waste tee with a large drain hose

clamp (provided). Use pliers to

squeeze clamp open and move into

position. If the drain hose was cut,

use a 1W' to 2" (3.8 to 5 cm) screw-

type clamp (not provided).

Option C, Waste disposer - with air gap

Drain trap

1. Using a hammer and screwdriver,

knock plug into disposer.

2. Use needle-nose pliers to remove

plug.

3. Connect rubber end of drain hose to

air gap and cut if needed.

NOTE: Do not cut ribbed section.

4.

Attach drain hose to air gap with

large drain hose clamp (provided).

Use pliers to squeeze clamp open

and move into position. If the drain

hose was cut, use a 11/2"to 2" (3.8 to

5 cm) screw-type clamp (not

provided).

5.

Use a rubber hose (not provided)

with screw-type clamps (not

provided) to connect from air gap to

disposer inlet.

10

Option D, No waste disposer - with air gap

1. Connect rubber end of drain hose to

air gap and cut if needed.

NOTE: Do not cut ribbed section.

2=

Attach drain hose to air gap with

large drain hose clamp (provided).

Use pliers to squeeze clamp open

and move into position. If the drain

hose was cut, use a 11/2'' to 2" (3.8 to

5 cm) screw-type clamp (not

provided).

3=

Use a rubber hose (not provided)

with screw-type clamps (not

provided) to connect from waste tee

to air gap.

Install moisture barrier i ............

(under a wood countertop)

Moisture

barrier

1=

2.

Make sure the area under the cabinet is clean and dry for

installation of the moisture barrier.

Remove the backing of the moisture barrier and apply to

underside of the countertop along the front edge of the

counter.

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Doing so can result in serious injury or cuts.

Excessive Weight Hazard

Use two or more people to move and install

dishwasher.

Failure to do so can result in back or other injury.

Helpful Tip: Place cardboard under dishwasher until installed in

cabinet opening to avoid damaging floor covering. Do not use

door panel as a worktable without first covering with a towel to

avoid scratching the door panel.

Using 2 or more people, grasp sides of dishwasher door frame

and place dishwasher on its back.

11

Option A, Remove Access Panel - Plastic Panel

Using a flat-blade screwdriver, turn the plastic fasteners 1/4turn

counterclockwise to unlock them. Remove panel. Do not remove

tech sheet from access panel.

Option B, Remove Access Panel - Metal Panel

Using a 1/4"hex head socket, nut driver or Phillips screwdriver,

remove 2 screws attaching access panel and lower panel to

dishwasher. Do not remove tech sheet from access panel.

® ®

Using a 1/4"hex head socket, nut driver or Torx _T20 screwdriver,

remove terminal box cover. Retain for later use.

Install a UL Listed/CSA Approved strain relief. Make sure screw

heads are facing to the left when tightening conduit nut. Strain

relief is provided with the power supply cord kit.

What type of electrical

connection will you use?

Power sUpPly Cord:

DireCt w re:

} Follow Option B instructions

NOTE: If using Option B, proceed to "Determine Cabinet

Opening," to continue with the installation of your dishwasher.

Option A, Power Supply Cord:

Route cord so that it does not touch dishwasher motor to lower

part of dishwasher tub. Pull cord through strain relief in terminal

box.

Select UL Listed/CSA Approved twist-on wire connectors rated to

connect your power supply cord to 16-gauge dishwasher wiring.

12

Electrical Shock Hazard

Electrically ground dishwasher.

Connect ground wire to green ground connector in

terminal box.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Ground

I ill "

__/ _ashe

Remove the ground connector screw and place through the ring

terminal of the green ground wire. Reattach and tighten the

ground connector screw.

Power Cord=Connect

re m a in in g w ires ...................................................................................................................

NOTE: Do not pre-twist stranded wire. Twist on wire connector.

Gently tug on wires to be sure both are secured.

)

Connect wires black to black and white to white, using UL

Listed/CSA Approved twist-on wire connectors.

If needed, see website for animated representation of this step.

Visit www.jenn-air.com/electrical under FAQ tab.

Tighten strain relief screws to secure cord.

Place wires inside terminal box. Insert tabs on left side of cover.

Make sure wires are tucked inside box. Close cover ensuring

wires are not pinched. Use 1/4"nut driver or Torx®T20®screwdriver

and previously removed screw to secure cover.

NOTE: Do not plug into outlet until instructed to do so.

13

©eeHn eCeb 'e/Ope g

Measure height of cabinet opening from underside of countertop

to floor where dishwasher will be installed (you will need to

measure the lowest point on the underside of the countertop and

the highest point on the floor). Refer to "Dishwasher Height

Adjustment Chart" for wheel position and the number of turns

needed.

Minmum wheel Number of turns Perforation

cutout height posmtlon on front eg on blanket

H

33s/4"(85.7 cm) remove all the way up remove

33%" (86 cm) remove all the wayup

|

34" (86,4 cm) 1 ' 10

34I/4' (87 Cm)

34_/2', (87.6 cm) 3 , 0

keep

keep j

NOTE: If the minimum cabinet opening height is less than 34"

(86.4 cm), the rear wheels can be removed for additional

clearance. This will allow the dishwasher to fit into a 337/8'' (86 cm)

high cabinet opening, but the dishwasher will be more difficult to

move. (Measurements are approximate. Wheels and legs are

preset at the factory for 34W' [87.6 cm].) If the minimum cabinet

opening height is 333/4'' (85.7 cm), a section in the insulation

blanket can be removed by cutting along the perforation.

Turn both leveler legs to the same height. Put wheels inthe

required position determined from "Dishwasher Height

Adjustment Chart."

Built-up floors: If the kitchen floor is higher than the cabinet

opening's floor - for example, the kitchen floor tile does not

extend into the cabinet opening - add shims as needed in the area

shown to bring the dishwasher up to 34" (86.4 cm) below the

countertop.

NOTE: Shims must be securely attached to floor to avoid

movement when the dishwasher is in use.

14

Euro handle

Pro-Style @

handle

Mountinc

stud

, Setscrew

i

(in bottom

of handle)

Hex key

Classic handle

_,_ Setscrew

(in bottom

Hex key of handle)

J

IMPORTANT: Do not scratch the front panel during this

procedure.

Remove the door handle and hardware bag containing the

setscrews and hex key from the cardboard box. Setscrews are

already installed in the handle. Place handle on mounting studs

with the setscrews facing down. Push the door handle tightly

against the door. Insert the short end of the hex key into the

setscrews. Tighten the setscrews 1/4turn past snug.

Retain hex key with Installation Instructions.

with control panel on the top

235/8.._r--_ ,,

(60 cm) | *292%2 (76 cm)

3/4"(19.1 mm)

*This dimension is for 4" (10.2 cm) toe kick. fthe

installation needs a higher toe kick, adjust the height

of the wood panel accordingly. Not recommended for

toe kicks greater than 6" (15.2 cm).

Follow steps below:

A customer supplied panel must weigh no more than 16 Ibs

(7.3 kg) and must be made to specific dimensions. It is

recommended that a cabinetmaker cut the customer panel

because of the precise dimensions needed.

NOTES:

• The handle for the custom panel is not included.

All mounting hardware supplied is for a 3/4"(19.1 mm) thick

wood panel. If a thinner wood panel or materials other than

wood are used, it is the customer's responsibility to obtain the

proper length screws and adjust the pilot holes accordingly.

IMPORTANT: Use a moisture-resistant sealer on both sides and

all edges of the panel to avoid damage from moisture.

15

Excessive Weight Hazard

Use two or more people to move and install

dishwasher.

Failure to do so can result in back or other injury.

Using 2 or more people, stand the dishwasher up.

NOTE: Do not install kick plate until instructed to do so.

1_ Custom panel installation

=':J Dishwashers with control |

p an eI o n t h e t o p .....

;cm)

%" (19.1 mm)

*This dimension isfor 4" (10.2 cm) toe kick. If the

installation needs a higher toe kick, adjust the height

of the wood panel accordingly. Not recommended for

toe kicks greater than 6" (15.2 cm).

J

Attach handle

Install the custom hardware handle(s) on the front of the wooden

panel inside dotted line.

IMPORTANT: If the handle is attached from the back of the

custom panel, the screw holes should be countersunk for the

screws heads to be flush with the panel. If the handle is attached

to the front of the custom panel, the screw lengths cannot exceed

the panel thickness.

Topof Panel

T_padelpanel

Dessusdupanneau

Centerline

Linea central

Axe central

Using the template provided, attach it to the backside of the

custom panel with tape. Make sure that the center of the template

is aligned with the center of the wooden panel and top of the

template is aligned to the top face of the wooden panel.

NOTE: Do not drill deeper then %" (16 mm) to keep from drilling

through panel. Pilot hole depths given are for 3/4"(19 mm) thick

panel.

Mark 4 pilot holes on the wooden panel using the template

provided. Predrill 4 pilot holes using a 3_32"drill bit. Use tape to

mark the drill bit to gauge hole depth. Drill pilot holes

approximately 5/8"(16 mm) into the custom panel.

16

Visible side

Attach the 4 plastic studs to the wooden panel using the 4 short

hex head (5/lo")screws provided.

Attach custom tape

Check custom tape alignment with metal door slots; verify tape is

right-side up, and that the tape does not overhang the metal door

on the top, bottom or side interfaces. Remove the backing from

the custom tape by pulling straight down on the liner. Align the

custom tape to the keyhole slots on the metal door (see image)

and apply. Repeat steps for one side and then the other.

NOTE: The adhesive on the tape is aggressive, so proper

alignment and attachment to the metal door needs to occur on

the first try.

Attach custom

assembly

Align the studs on the custom wood panel to the keyhole slots on

the door assembly. Ensure that all 4 plastic studs are engaged in

the keyhole slots. Slide wood panel down until the top surface of

the wooden panel is flush with the top of the door.

Customer-supplied

panel

Drill through

these holes.

Remove 2 short screws

and replace with long

screws provided,

Open the door and align top edges. Predrill 2 pilot holes using a

3/32"drill bit. Use tape to mark the drill bit to gauge hole depth. Drill

pilot holes approximately 11/2"(3.8 cm) into the top corners of the

door using hole in liner as a guide.

Customer-supplied

panel

top

edges

:)rill through

theseholes

Install 2 long screws supplied in top corners to secure custom

wood panel in place.

17

Remove the short screws

edges

Remove 2 short screws Customer-supplied

and replace with long panel

screws provided.

Remove the short screws (3rd from top) on either side of the inner

door panel. Predrill 2 pilot holes using a 3/32"drill bit. Use tape to

mark the drill bit to gauge the hole depth. Drill pilot holes

approximately 11/2"(3.8 cm) using the door liner hole as a guide

into the panel. Install the 2 remaining long screws.

Excessive Weight Hazard

Use two or more people to move and install

dishwasher.

Failure to do so can result in back or other injury.

Use 2 or more people to move and install dishwasher.

IMPORTANT: The dishwasher must be secured to the cabinet.

There are two brackets found in the parts bag. Attach the

brackets using Option A if the countertop is wood, laminate or

another similar surface. If your countertop is marble, granite or

another hard surface, install using Option B.

Option A, Countertop attachment:

Tabsmust point

....... ._/ t0 the right

Remove the brackets from the package and insert into the open

slots on the left and right-hand top of the dishwasher collar as

shown.

Using a pair of pliers, bend the tab down to secure the bracket in

place. Repeat this step for the other side.

NOTE: Do not attach the dishwasher. This will be done later.

Option B, Dishwasher side attachment:

NOTE: Removethe brackets from the partspackage.

Break off the end of the bracket along the scored line.

With another person holding the rear of the dishwasher to keep it

from tipping, open dishwasher door and place towel over pump

assembly and spray arm of dishwasher. This will keep screws

from falling into pump area when you are securing dishwasher to

cabinet.

Push the plastic buttons out of the side of the tub.

NOTE: Save the buttons to cover the holes after dishwasher is

installed.

J Install bracket

\

Bend

tabs

J

Push bracket into slot on the side of dishwasher, and bend tab in

toward the side of the dishwasher so that it keeps the bracket in

place. Repeat this step for the other side of the dishwasher.

NOTE: Do not attach the dishwasher. This will be done later.

18

_,,,,t/_5 _

Copper tubing only: Slide nut. then ferrule, about 1" (2.5 cm) onto

copper tubing.

NOTE: To avoid vibration during operation, route the water supply

line so that it does not touch the dishwasher base. frame or motor.

21 Add 90 ° elbow fittingto the'

water supply line I _

Connect the 3/8"compression fitting to the water supply line prior

to installing the unit into the cabinet opening. Attach such that the

3/4"connection is facing upward as shown above.

Copper tubing only: Put the tubing into the 90° elbow fitting as far

as it will go (the copper tubing bends and kinks easily). Slide the

nut and ferrule forward and start the nut onto the elbow threads.

Flexible braided connection: Secure nut to elbow using 5/8"open

ended wrench or adjustable wrench.

NOTE: Do not use Teflon ®ttape with compression fittings.

1-®TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

Excessive Weight Hazard

Use two or more people to move and install

dishwasher.

Failure to do so can result in back or other injury.

Using 2 or more people, stand dishwasher, upright.

NOTE: Do not install kick plate until instructed to do so.

IMPORTANT: Double-check correct placement of utilities. Grasp

the sides of the dishwasher at the edges of the door panel. Tilt

dishwasher backward on wheels and move dishwasher close to

cabinet opening.

NOTE: Do not push on the front of the panel or on the console.

Panel or console may dent.

Helpful Tip: Temporarily tape utilities to the floor in the locations

shown to prohibit them from moving when dishwasher is moved

into the cabinet opening.

19

Check that water line is on the left side of opening and drain hose

is near the center of the cabinet opening.

Open and close door

With another person holding the dishwasher to keep it from

tipping, open and close the door a few times. If the door closes or

falls open under its own weight, the door tension will need to be

adjusted.

To adjust the door spring tension, unhook the spring from the rear

leg of dishwasher.

Using a %6" nut driver or hex socket, remove the screw from the

tensioner.

The screw can be put into one of three holes (1, 2, 3) in the front

leg of dishwasher. If the door closes by itself, move the tensioner

to a higher number hole and replace the screw. Reattach door

spring to rear leg.

NOTE: Tensioners on both sides of dishwasher should be secured

at same holes.

When door is unlatched and door opens by itself, move the

tensioner to a lower numbered hole and replace the screw.

Reattach door spring to rear leg.

NOTE: Tensioners on both sides of dishwasher should be secured

at same holes.

IMPORTANT: If wheels were removed, cover the floor when

moving the dishwasher to avoid damage to the floor. Slowly move

dishwasher completely into cabinet opening. Do not kink or pinch

water line, drain hose, power supply cord or direct wire between

dishwasher and cabinet. Remove cardboard from under

dishwasher.

NOTES:

• It is all right if dishwasher fits tightly into cabinet opening. Do

not remove insulation blanket - the blanket reduces the sound

level.

• If using power cord, make sure to route end through hole in

cutout before sliding dishwasher into cabinet opening.

Align front of dishwasher door panel with front of cabinet doors.

You may need to adjust alignment to be even with your cabinets.

2O

La page charge ...

Jenn-Air JDB8200AWP3 Guide d'installation

Jenn-Air JDB8200AWP3 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents