Indesit IWDC 7125 B (EX)60HZ Mode d'emploi

Marque: Indesit

Modèle: IWDC 7125 B (EX)60HZ

Catégorie: Machines à laver

Taper: Mode d'emploi

Contents

Installation, 2-3-4-5

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

Technical data

Description of the washer-dryer and

starting a wash cycle, 6-7

Control panel

Indicator lights

Starting a wash cycle

Wash cycles, 8

Table of wash cycles

Personalisation, 9

Setting the temperature

Setting the drying cycle

Functions

Detergents and laundry, 10

Detergent dispenser drawer

Preparing the laundry

Garments requiring special care

Load balancing system

Precautions and tips, 11

General safety

Disposal

Opening the porthole door manually

Care and maintenance, 12

Cutting off the water or electricity supply

Cleaning the washer-dryer

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Troubleshooting, 13

Service, 14

IWDC 7125

Instructions for use

WASHER-DRYER

English,1

Français,15

, 29

 This symbol reminds you to read this instruction manual.

Installation

 This instruction manual should be kept in a safe

place for future reference. If the washer-dryer is sold,

transferred or moved, make sure that the instruction

manual remains with the machine so that the new

owner is able to familiarise himself/herself with its

operation and features.

 Read these instructions carefully: they contain vital

information relating to the safe installation and

operation of the appliance.

Unpacking and levelling

Unpacking

1. Remove the washer-dryer from its packaging.

2. Make sure that the washer-dryer has not been

damaged during the transportation process. If it has

been damaged, contact the retailer and do not

proceed any further with the installation process.

3. Remove the 4

protective screws (used

during transportation) and

the rubber washer with

the corresponding

spacer, located on the

rear part of the appliance

(see figure).

4. Close off the holes using the plastic plugs provided.

5. Keep all the parts in a safe place: you will need

them again if the washer-dryer needs to be moved to

another location.

 Packaging materials should not be used as toys for

children.

Levelling

1. Install the washer-dryer on a flat sturdy floor,

without resting it up against walls, furniture cabinets

or anything else.

2. If the floor is not

perfectly level, compen-

sate for any unevenness

by tightening or loosening

the adjustable front feet

(see figure); the angle of

inclination, measured in

relation to the worktop,

must not exceed 2°.

Levelling the machine correctly will provide it with

stability, help to avoid vibrations and excessive noise

and prevent it from shifting while it is operating. If it is

placed on carpet or a rug, adjust the feet in such a

way as to allow a sufficient ventilation space

underneath the washer-dryer.

Connecting the electricity and water

supplies

Connecting the water inlet hose

1. Connect the supply

pipe by screwing it to a

cold water tab using a ¾

gas threaded connection

(see figure).

Before performing the

connection, allow the

water to run freely until it

is perfectly clear.

2. Connect the inlet hose

to the washer-dryer by

screwing it onto the

corresponding water inlet

of the appliance, which is

situated on the top right-

hand side of the rear part

of the appliance (see

figure).

3. Make sure that the hose is not folded over or bent.

 The water pressure at the tap must fall within the

values indicated in the Technical details table (see

next page).

 If the inlet hose is not long enough, contact a

specialised shop or an authorised technician.

 Never use second-hand hoses.

 Use the ones supplied with the machine.

Connecting the drain hose

Connect the drain hose,

without bending it, to a

draining duct or a wall

drain situated between

65 and 100 cm from the

floor;

alternatively, place it over

the edge of a basin, sink

or tub, fastening the

duct supplied to the tap

(see figure). The free end

of the hose should not

be underwater.

 We advise against the use of hose extensions; in

case of absolute need, the extension must have the

same diameter as the original hose and must not

exceed 150 cm in length.

Electric connection

Before plugging the appliance into the mains socket,

make sure that:

 the socket is earthed and in compliance with the

applicable law;

 the socket is able to sustain the appliance's

maximum power load indicated in the Technical

details table (see page 5);

 the supply voltage is included within the values i

ndicated on the Technical details table

(see page 5);

 the socket is compatible with the washing

machine's plug. If this is not the case, replace

the socket or the plug.

Your appliance is now supplied with a 13 amp fused

plug it can be plugged into a 13 amp socket for

immediate use. Before using the appliance please

read the instructions below.

WARNING - THIS APPLIANCE MUST BE EARTHED.

THE FOLLOWING OPERATIONS SHOULD BE

CARRIED OUT BY A QUALIFIED ELECTRICIAN.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA

approved fuse to BS 1362 should always be used,

and the fuse cover re-fitted. If the fuse cover is lost,

the plug must not be used until a replacement is

obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be of the

correct colour as indicated by the coloured marking

or the colour that is embossed in words on the base

of the plug. Replacements can be obtained directly

from your nearest Service Depot.

Removing the plug:

If your appliance has a non-rewireable moulded plug

and you should wish to re-route the mains cable

through partitions, units etc., please ensure that

either:

the plug is replaced by a fused 13 ampere re-

wearable plug bearing the BSI mark of approval.

or:

the mains cable is wired directly into a 13 amp cable

outlet, controlled by a switch, (in compliance with BS

5733) which is accessible without moving the

appliance.

Disposing of the plug:

Ensure that before disposing of the plug itself, you

make the pins unusable so that it cannot be

accidentally inserted into a socket.

Instructions for connecting cable to an alternative plug:

Important: the wires in the mains lead are coloured in

accordance with the following code:

Green & Yellow Earth

Blue Neutral

Brown Live

As the colours of the wires in the lead may not

correspond with the coloured markings identifyng the

terminals in your plug, proceed as follows:

Connect Green & Yellow wire to terminal marked E or

or coloured Green or Green & Yellow.

Connect Brown wire to terminal marked L or

coloured Red.

Connect Blue wire to terminal marked N or coloured

Black.

65 - 100 cm

If a 13 amp plug (BS 1363) is used it must be fitted

with a

13 amp fuse, either in the plug or adaptor or at the

distribution board.

If you are in any doubt the electrical supply to your

machine, consult a qualified electrician before use.

How to connect an alternative plug:

The wires in this mains lead are coloured in

accordance with the following code:

BLUE NEUTRAL (N)

BROWN LIVE (L)

GREEN & YELLOW EARTH (E)

Disposing of the appliance:

When disposing of the appliance please remove the

plug by cutting the mains cable as close as possible

to the plug body and dispose of it as described above.

 The washing machine should not be installed in an

outdoor environment, not even when the area is

sheltered, because it may be very dangerous to leave

it exposed to rain and thunderstorms.

 When the washing machine is installed, the mains

socket must be within easy reach.

 Do not use extensions or multiple sockets.

 The power supply cable must never be bent or

dangerously compressed.

 The power supply cable must only be replaced by

an authorised serviceman.

Warning! The company denies all liability if and when

these norms are not respected.

GREEN &

YELLOW

BROWN

BLUE

13 ampere fuse

CROSS-BAR

CORD GRIP

The first wash cycle

Once the appliance has been installed, and before

you use it for the first time, run a wash cycle with

detergent and no laundry, using the wash cycle 2.

Technical data

Model

IWDC 7125

Dimensions

width 59.5 cm

height 85 cm

depth 53,5 cm

Capacity

from 1 to 7 kg for the wash programme;

from 1 to 5 kg for the drying programme

Electrical

connections

please refer to the technical data plate fixed

to the machine

Wate r

connections

maximum pressure 1 MPa (10 bar)

minimum pressure 0.05 MPa (0.5 bar)

drum capacity 52 litres

Spin speed

up to 1200 rotations per minute

Energy

rated

programmes

according to

regulation

EN 50229

Wash: programme 2; temperature 60°C;

run with a load of 7 kg.

Drying: first drying cycle performed with a 2 kg

load and the DRYING knob on the setting;

Second drying cycle performed with a 5 kg

load and the DRYING knob on the setting.

This appliance conforms to the following

EC Directives:

- 89/336/EEC dated 03/05/89

(Electromagnetic Compatibility) and

subsequent modifications

- 2002/96/EC

- 2006/95/EC Low Voltage)

Detergent dispenser drawer: used to dispense

detergents and washing additives (see Detergents

and laundry).

ON/OFF button: switches the washer-dryer on and

off.

WASH CYCLE knob: programmes the wash cycles.

During the wash cycle, the knob does not move.

FUNCTION buttons with indicator light: used to

select the available functions. The indicator light

corresponding to the selected function will remain lit.

TEMPERATURE knob: sets the temperature or the

cold wash cycle (see Personalisation).

DRYING knob: used to set the desired drying

programme (see Personalisation).

WASH CYCLE PROGRESS/DELAY TIMER

indicator light

s: used to monitor the progress of the

wash cycle.

The illuminated indicator light shows which phase is in

progress.

If the Delay Timer function has been set, the time

remaining until the wash cycle starts will be indicated

(see next page).

DOOR LOCKED indicator light: indicates whether

the door may be opened or not (see next page).

START/PAUSE button with indicator light: starts or

temporarily interrupts the wash cycles.

N.B. To pause the wash cycle in progress, press this

button; the corresponding indicator light will flash

orange, while the indicator light for the current wash

cycle phase will remain lit in a fixed manner. If the

DOOR LOCKED

indicator light is switched off, the

door may be opened.

To start the wash cycle from the point at which it was

interrupted, press this button again.

Standby mode

This washing machine, in compliance with new

energy saving regulations, is fitted with an automatic

standby system which is enabled after about 30

minutes if no activity is detected. Press the ON-OFF

button briefly and wait for the machine to start up

again.

Description of the washer-dryer and

starting a wash cycle

WASH CYCLE PROGRESS/

DELAY TIMER

indicator lights

DOOR LOCKED

indicator light

START/

PAUSE

button with

indicator light

Control panel

Detergent dispenser drawer

ON/OFF

button

WASH CYCLE

knob

TEMPERATURE

knob

FUNCTION

buttons with

indicator lights

DRYING

knob

Indicator lights

The indicator lights provide important information.

This is what they can tell you:

Delayed start

If the DELAY TIMER function has been activated (see

Personalisation), after the wash cycle has been

started the indicator light corresponding to the

selected delay period will begin to flash:

As time passes, the remaining delay will be displayed

and the corresponding indicator light will flash:

The set programme will start once the selected time

delay has expired.

Wash cycle phase indicator lights

Once the desired wash cycle has been selected and has

begun, the indicator lights switch on one by one to

indicate which phase of the cycle is currently in progress.

Note: when the drying cycle has finished, the

DRYING knob should be returned to the 0 position.

Function buttons and corresponding indicator lights

When a function is selected, the corresponding

indicator light will illuminate.

If the selected function is not compatible with the

programmed wash cycle, the corresponding indicator

light will flash and the function will not be activated.

If the selected function is not compatible with another

function which has been selected previously, the

indicator light corresponding to the first function

selected will flash and only the second function will be

activated; the indicator light corresponding to the

enabled option will remain lit.

Door locked indicator light

When the indicator light is on, the porthole door is

locked to prevent it from being opened; make sure

the indicator light is off before opening the door. To

open the door during a running wash cycle, press the

START/PAUSE button; the door may be opened once

the DOOR LOCKED indicator light turns off.

Starting a wash cycle

1. Switch the washer-dryer on by pressing the ON/OFF button. All indicator lights will switch on for a few

seconds, then they will switch off and the START/PAUSE indicator light will pulse.

2. Load the laundry and close the door.

3. Set the WASH CYCLE knob to the desired programme.

4. Set the washing temperature (see Personalisation).

5. Set the drying cycle if necessary (see Personalisation).

6. Measure out the detergent and washing additives (see Detergents and laundry).

7. Select the desired functions.

8. Start the wash cycle by pressing the START/PAUSE button and the corresponding indicator light will remain lit

in a fixed manner, in green.

To cancel the set wash cycle, pause the machine by pressing the START/PAUSE button and select a new cycle.

9. At the end of the wash cycle the

indicator light will switch on. The door can be opened once the DOOR

LOCKED

indicator light turns off. Take out your laundry and leave the appliance door ajar to make sure the

drum dries completely. Switch the washer-dryer off by pressing the ON/OFF button.

Wash

Rinse

Spin/Drain

Drying

End of wash cycle

Specials wash cycles

Sport Light (

wash cycle

9) is for washing lightly soiled sports clothing fabrics (tracksuits, shorts, etc.); for best

results, we recommend not exceeding the maximum load indicated in the "Table of wash cycles". We recommend

using a liquid detergent and dosage suitable for a half-load.

Sport Shoes (

wash cycle

10) is for washing sports shoes; for best results, do not wash more than 2 pairs

simultaneously.

Express Wash & Dry (

wash cycle

13) was designed to wash and dry lightly soiled garments quickly. This cycle may

be used to wash and dry a laundry load of up to 0.5 kg in just 35 minutes.

To achieve optimum results, use liquid detergent and pre-treat cuffs, collars and stains.

Wash cycles

The information contained in the table is intended as a guide only.

For all Test Institutes:

1) Test wash cycle in compliance with regulation EN 50229: set wash cycle 2 with a temperature of 60°C.

2) Long wash cycle for cottons: set wash cycle 2 with a temperature of 40°C.

3) Short wash cycle for cottons: set wash cycle 4 with a temperature of 40°C.

Wash cycles

Table of wash cycles

Description of the wash cycle

Max

temp.

(°C)

Max.

speed

(rpm)

Drying

Detergents

Max. load

(kg)

Cycle

duration

Pre-

wash

Wash

Fabric

softener

Normal

Eco

Time

Normal

Eco

Time

Daily

Cotton with prewash:

extremely soiled whites.

90° 1200

lll l

171

Cotton:

extremely soiled whites.

90° 1200

155

Cotton (1):

heavily soiled whites and resistant colours.

60° 1200

153

Cotton (2):

heavily soiled whites and delicate colours.

40° 1200

147

Cotton:

heavily soiled whites and resistant colours.

60° 1200

73,5130104

Coloured Cottons (3):

lightly soiled whites and delicate colours.

40° 1200

73,59271

Synthetics:

heavily soiled resistant colours.

60° 800

328572

Special

Wool:

for wool, cashmere, etc.

40° 600

- -

1,5

Silk/Curtains:

for garments in silk and viscose, lingerie.

30° 0

- -

Jeans

40° 800

Sport Light

30° 600

- -

Sport Shoes

30° 600

- -

Max. 2

pairs

Drying

Cotton dry

- -

- - -

Synthetics dry

- -

- - -

Express Wash & Dry

30° 1200

0,5

Partial wash cycles

Rinse

1200

- -

Spin

1200

- - -

Drain

- - - -

Setting the temperature

Turn the TEMPERATURE knob to set the wash temperature (see Table of wash cycles).

The temperature may be lowered, or even set to a cold wash

. The washer-dryer will automatically prevent you

from selecting a temperature which is higher than the maximum value set for each wash cycle.

Setting the drying cycle

Turn the DRYING knob to select the desired drying

option. There are two options:

A - Based on time: From 40 minutes to 180.

B - Based on the desired laundry dryness level:

Iron dry

: suitable for clothes which will need ironing

afterwards. the remaining dampness softens creases,

making them easier to remove.

Hanger dry

: ideal for clothes which do not need to

be dried fully.

Cupboard dry

: suitable for laundry which can be put back in a cupboard without being ironed.

If your laundry load to be washed and dried is much greater than the maximum stated load (see adjacent table),

perform the wash cycle, and when the cycle is complete, divide the garments into groups and put some of them back

in the drum. At this point, follow the instructions provided for a "Drying only" cycle. Repeat this procedure for the

remainder of the load.

Drying only

Use the cycle selector knob to select a drying cycle (11-12) in accordance with the type of fabric. The desired drying

level or time may also be set using the DRYING knob.

Functions

The various wash functions available with this washer-dryer will help to achieve the desired results, every time.

To activate the functions:

1. Press the button corresponding to the desired function;

2. the function is enabled when the corresponding indicator light is illuminated.

Note: If the indicator light flashes rapidly, this signals that this particular function may not be selected in

conjunction with the selected wash cycle.

Selecting this option enables you to suitably adjust drum rotation, temperature and water to a reduced load of lightly

soiled cotton and synthetic fabrics (refer to the

"Table of wash cycles"

).   enables you to wash in less time

thereby saving water and electricity. We suggest using a liquid detergent suitably measured out to the load quantity.

 This function may not be used in conjunction with cycles 1, 2, 6, 7, 8, 9, 10, 11, 12, 13, , , .

1200-600

Press this button to reduce the spin speed.

 This function may not be used in conjunction with cycles 7, 11, 12, 13, .

Easy iron

By selecting this function, the wash and spin cycles will be modified in order to reduce the formation of creases. At

the end of the cycle the Washer-dryer will perform slow rotations of the drum; the indicator lights for the EASY

IRON and START/PAUSE options will flash (the first one green, the second orange) and the "END" indicator light

turns on. To end the cycle, press the START/PAUSE button or the EASY IRON button.

For the 7 wash cycle, the machine will end the cycle while the laundry is soaking and the EASY IRON and START/

PAUSE indicator lights will flash. To drain the water so that the laundry may be removed, press the START/PAUSE

button or the EASY IRON button.

 This function may not be used in conjunction with cycles 6, 9, 10, 11, 12, 13,

, .

Note: If you also want to run the drying cycle, this option is enabled only if combined with level

(Iron dry).

Delay timer

This timer delays the start time of the wash cycle by up to 9 hours. Press the button repeatedly until the indicator light

corresponding to the desired delay time switches on. The fourth time the button is pressed, the function will be disabled.

N.B. Once the START/PAUSE button has been pressed, the delay time can only be modified by decreasing it until launching

the set programme.

 This option is enabled with all programmes.

Personalisation

Fabric

type

Load type Max.

load

(kg)

Cupboard

dry

Hanger

dry

Iron

dry

Cotton Clothing of different

sizes, Terry towels

5180170140

Synthetics Sheets, Shirts, Pyjamas,

socks, etc.

3 140 120 100

Table of Drying times (guideline values)

Detergents and laundry

Detergent dispenser drawer

Good washing results also depend on the correct

dose of detergent: adding too much detergent will not

necessarily result in a more efficient wash, and may in

fact cause build up on the inside of your appliance

and contribute to environmental pollution.

 Do not use hand washing detergents because these

create too much foam.

Open the detergent

dispenser drawer and

pour in the detergent or

washing additive, as

follows.

compartment 1: Pre-wash detergent (powder)

compartment 2: Detergent for the wash cycle

(powder or liquid)

Liquid detergent should only be poured in immediately

prior to the start of the wash cycle.

compartment 3: Additives (fabric softeners, etc.)

The fabric softener should not overflow the grid.

Preparing the laundry

 Divide the laundry according to:

- the type of fabric/the symbol on the label

- the colours: separate coloured garments from

whites.

 Empty all garment pockets and check the buttons.

 Do not exceed the listed values, which refer to the

weight of the laundry when dry:

Durable fabrics: max. 7 kg

Synthetic fabrics: max. 3 kg

Delicate fabrics: max. 2 kg

Wool: max. 1,5 kg

Silk: max. 1 kg

How much does your laundry weigh?

1 sheet 400-500 g

1 pillow case 150-200 g

1 tablecloth 400-500 g

1 bathrobe 900-1200 g

1 towel 150-250 g

Garments requiring special care

Wool: all wool garments can be washed using

programme 6, even those carrying the "hand-wash

only"

label. For best results, use special

detergents and do not exceed 1,5 kg of laundry.

Silk: use special wash cycle 7 to wash all silk

garments. We recommend the use of special

detergent which has been designed to wash delicate

clothes.

Curtains: fold curtains and place them in a pillow

case or mesh bag. Use wash cycle 7.

Jeans: Turn garments inside-out before washing and

use a liquid detergent. Use programme 8.

Load balancing system

Before every spin cycle, to avoid excessive vibrations

and to distribute the load in a uniform manner, the

drum rotates continuously at a speed which is slightly

greater than the washing rotation speed. If, after

several attempts, the load is not balanced correctly,

the machine spins at a reduced spin speed. If the

load is excessively unbalanced, the washer-dryer

performs the distribution process instead of spinning.

To encourage improved load distribution and balance,

we recommend small and large garments are mixed

in the load.

Precautions and tips

 This washer-dryer was designed and constructed in

accordance with international safety regulations. The following

information is provided for safety reasons and must therefore

be read carefully.

General safety

 This appliance was designed for domestic use only.

 This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental

capabilities, or lack of experience and knowledge, unless

they have been given supervision or instruction concerning

use of the appliance by a person responsible for their

safety. Children should be supervised to ensure that they

do not play with the appliance.

 Do not dry unwashed items in the tumble dryer.

 Items that have been soiled with substances such as

cooking oil, acetone, alcohol, petrol, kerosene, spot

removers, turpentine, waxes and wax removers should be

washed in hot water with an extra amount of detergent

before being dried in the tumble dryer.

 Items such as foam rubber (latex foam), shower caps,

waterproof textiles, rubber backed articles and clothes or

pillows fitted with foam rubber pads should not be dried in

the tumble dryer.

 Fabric softeners, or similar products, should be used as

specified by the fabric softener instructions.

 The final part of a tumble dryer cycle occurs without heat

(cool down cycle) to ensure that the items are left at a

temperature that ensures that the items will not be

damaged.

WARNING: Never stop a tumble dryer before the end of the

drying cycle unless all items are quickly removed and

spread out so that the heat is dissipated.

 Do not touch the machine when barefoot or with wet or

damp hands or feet.

 Do not pull on the power supply cable when unplugging the

appliance from the electricity socket. Hold the plug and pull.

 Do not open the detergent dispenser drawer while the

machine is in operation.

 Do not touch the drained water as it may reach extremely

high temperatures.

 Never force the porthole door. This could damage the

safety lock mechanism designed to prevent accidental

opening.

 If the appliance breaks down, do not under any

circumstances access the internal mechanisms in an

attempt to repair it yourself.

 Always keep children well away from the appliance while it is

operating.

 The door can become quite hot during the wash cycle.

 If the appliance has to be moved, work in a group of two or

three people and handle it with the utmost care. Never try

to do this alone, because the appliance is very heavy.

 Before loading laundry into the washer-dryer, make sure the

drum is empty.

 During the drying phase, the door tends to get

quite hot.

 Do not use the appliance to dry clothes that have

been washed with flammable solvents (e.g.

trichlorethylene).

 Do not use the appliance to dry foam rubber or

similar elastomers.

 Make sure that the water tap is turned on during

the drying cycles.

Disposal

 Disposing of the packaging materials:

observe local regulations so that the packaging may be re-

used.

 The European Directive 2002/96/EC relating to Waste

Electrical and Electronic Equipment (WEEE) states that

household appliances should not be disposed of using the

normal solid urban waste cycle. Exhausted appliances

should be collected separately in order to optimise the cost

of re-using and recycling the materials inside the machine,

while preventing potential damage to the atmosphere and

to public health. The crossed-out dustbin is marked on all

products to remind the owner of their obligations regarding

separated waste collection.

For more information relating to the correct disposal of

household appliances, owners should contact their local

authorities or appliance dealer.

Opening the porthole door manually

In the event that it is not possible to open the porthole

door due to a powercut, and if you wish to remove the

laundry, proceed as follows:

1. remove the plug from the electrical socket.

2. make sure the water level inside the machine is lower

than the door opening; if it is not, remove excess water

using the drain hose, collecting it in a bucket as indicated in

the figure.

3. using a screwdriver, remove the cover panel on the

lower front part of the washing machine (see figure).

4. pull outwards using the tab as indicated in the figure,

until the plastic tie-rod is freed from its stop position; pull

downwards and open the door at the same time.

5. reposition the panel, making sure the hooks are securely

in place before you push it onto the appliance.

Care and maintenance

Cutting off the water and electricity

supplies

 Turn off the water tap after every wash cycle. This

will limit wear on the hydraulic system inside the

washer-dryer and help to prevent leaks.

 Unplug the washer-dryer when cleaning it and

during all maintenance work.

Cleaning the washer-dryer

The outer parts and rubber components of the

appliance can be cleaned using a soft cloth soaked

in lukewarm soapy water. Do not use solvents or

abrasives.

Cleaning the detergent dispenser

drawer

Remove the dispenser

by raising it and pulling it

out (see figure).

Wash it under running

water; this operation

should be repeated

frequently.

Caring for the door and drum of your

appliance

 Always leave the porthole door ajar in order to

prevent unpleasant odours from forming.

Cleaning the pump

The washer-dryer is fitted with a self-cleaning pump

which does not require any maintenance. Sometimes,

small items (such as coins or buttons) may fall into the

pre-chamber which protects the pump, situated in its

bottom part.

 Make sure the wash cycle has finished and unplug

the appliance.

To access the pre-chamber:

1. using a screwdriver,

remove the cover panel

on the lower front part of

the washer-dryer (see

figure);

2. unscrew the lid by

rotating it anti-clockwise

(see figure): a little water

may trickle out. This is

perfectly normal;

3. clean the inside thoroughly;

4. screw the lid back on;

5. reposition the panel, making sure the hooks are

securely in place before you push it onto the

appliance.

Checking the water inlet hose

Check the inlet hose at least once a year. If there are

any cracks, it should be replaced immediately: during

the wash cycles, water pressure is very strong and a

cracked hose could easily split open.

 Never use second-hand hoses.

Troubleshooting

Your washer-dryer could fail to work. Before contacting the Technical Assistance Centre (see Assistance), make

sure that the problem cannot be not solved easily using the following list.

Problem:

The Washer-dryer does not

switch on.

The wash cycle does not start.

The Washer-dryer does not take

in water (the indicator light for

the first wash cycle stage

flashes rapidly).

The Washer-dryer continuously

takes in and

drains water.

The Washer-dryer does not drain

or spin.

The Washer-dryer vibrates a lot

during the spin cycle.

The Washer-dryer leaks.

The "functions" indicator lights and the

"start/pause" indicator light flash, while

one of the "phase in progress" indicator

lights and the "door locked" indicator

light will remain lit in a fixed manner.

There is too much foam.

The washer-dryer does not dry.

Possible causes / Solutions:

 The appliance is not plugged into the socket fully, or is not making contact.

 There is no power in the house.

 The Washer-dryer door is not closed properly.

 The ON/OFF button has not been pressed.

 The START/PAUSE button has not been pressed.

 The water tap has not been opened.

 A delayed start has been set.

 The water inlet hose is not connected to the tap.

 The hose is bent.

 The water tap has not been opened.

 There is no water supply in the house.

 The pressure is too low.

 The START/PAUSE button has not been pressed.

 The drain hose is not fitted at a height between 65 and 100 cm from

the floor (see Installation).

 The free end of the hose is under water (see Installation).

 The wall drainage system is not fitted with a breather pipe.

If the problem persists even after these checks, turn off the water tap, switch

the appliance off and contact the Assistance Service. If the dwelling is on one of

the upper floors of a building, there may be problems relating to water drainage,

causing the Washer-dryer to fill with water and drain continuously. Special anti-

draining valves are available in shops and help to avoid this inconvenience.

 The wash cycle does not include draining: some wash cycles require the

drain phase to be started manually.

 The Easy iron option has been activated: To complete the wash cycle,

press the START/PAUSE button (see Wash cycles and options).

 The drain hose is bent (see Installation).

 The drainage duct is clogged.

 The drum was not unlocked correctly during installation (see Installation).

 The Washer-dryer is not level (see Installation).

 The Washer-dryer is trapped between cabinets and walls (see Installation).

 The water inlet hose is not screwed on properly (see Installation).

 The detergent dispenser drawer is blocked (for cleaning instructions, see Care

and maintenance).

 The drain hose is not fixed properly (see Installation).

 Switch off the machine and unplug it, wait for approximately 1 minute

and then switch it back on again.

If the problem persists, contact the Technical Assistance Service.

 The detergent is not suitable for machine washing (it should display the

text for Washer-dryers or hand and machine wash, or the like).

 Too much detergent was used.

 The appliance is not plugged into the socket, or not enough to make contact.

 There has been a power failure.

 The appliance door is not shut properly.

 A delayed start has been set.

 DRYING knob is in the 0 position.

Service

Before calling for Assistance:

 Check whether you can solve the problem alone (see Troubleshooting);

 Restart the programme to check whether the problem has been solved;

 If this is not the case, contact an authorised Technical Assistance Centre using the telephone number

provided on the guarantee certificate.

 Always request the assistance of authorised technicians.

Have the following information to hand:

 the type of problem;

 the appliance model (Mod.);

 the serial number (S/N).

This information can be found on the data plate applied to the rear of the washer-dryer, and can also be

found on the front of the appliance by opening the door.

Français

Sommaire

Installation, 16-17-18-19

Déballage et mise à niveau

Raccordements eau et électricité

Premier cycle de lavage

Caractéristiques techniques

Description du lavante-séchante et

démarrage dun programme, 20-21

Bandeau de commandes

Voyants

Démarrage dun programme

Programmes, 22

Tableau des programmes

Personnalisations, 23

Sélection de la température

Sélectionner le séchage

Fonctions

Produits lessiviels et linge, 24

Tiroir à produits lessiviels

Triage du linge

Linge ou vêtements particuliers

Système déquilibrage de la charge

Précautions et conseils, 25

Sécurité générale

Mise au rebut

Ouverture manuelle de la porte hublot

Entretien et soin, 26

Coupure de larrivée deau et du courant

Nettoyage du lavante-séchante

Nettoyage du tiroir à produits lessiviels.

Entretien du hublot et du tambour

Nettoyage de la pompe

Contrôle du tuyau darrivée de leau

Anomalies et remèdes, 27

Assistance, 28

IWDC 7125

Mode demploi

LAVANTE-SÉCHANTE

! Ce symbole vous rappelle de lire ce mode d'emploi.

Installation

 Conserver ce mode demploi pour pouvoir le

consulter à tout moment. En cas de vente, de

cession ou de déménagement, veiller à ce quil suive

toujours le lavante-séchante pour que son nouveau

propriétaire soit informé sur son mode de

fonctionnement et puisse profiter des conseils

correspondants.

 Lire attentivement les instructions: elles fournissent

des conseils importants sur linstallation, lutilisation et

la sécurité de lappareil.

Déballage et mise à niveau

Déballage

1. Déballer le lavante-séchante.

2. Contrôler que le lavante-séchante na pas été

endommagé pendant le transport. Sil est abîmé, ne

pas le raccorder et contacter le vendeur.

3. Enlever les 4 vis de

protection servant au

transport, le caoutchouc

et la cale, placés dans la

partie arrière (voir figure).

4. Boucher les trous à laide des bouchons plastique

fournis.

5. Conserver toutes ces pièces: il faudra les remonter

en cas de transport du lavante-séchante.

 Les pièces demballage ne sont pas des jouets pour

enfants.

Mise à niveau

1. Installer le lavante-séchante sur un sol plat et

rigide, sans lappuyer contre des murs, des meubles

ou autre.

2. Si le sol nest pas

parfaitement horizontal,

visser ou dévisser les

pieds de réglage avant

(voir figure) pour niveler

lappareil; son angle

dinclinaison, mesuré sur

le plan de travail, ne doit

pas dépasser 2°.

Une bonne mise à niveau garantit la stabilité de

lappareil et évite quil y ait des vibrations, du bruit et

des déplacements en cours de fonctionnement. Si la

machine est posée sur de la moquette ou un tapis,

régler les pieds de manière à ce quil y ait

suffisamment despace pour assurer une bonne

ventilation.

Raccordements eau et électricité

Raccordement du tuyau darrivée de leau

1. Reliez le tuyau

d'alimentation en le

vissant à un robinet d'eau

froide à embout fileté 3/4

gaz (voir figure).

Faire couler leau jusquà

ce quelle soit limpide et

sans impuretés avant de

raccorder.

2. Raccorder le tuyau

darrivée de leau au

lavante-séchante en le

vissant à la prise deau

prévue, dans la partie

arrière en haut à droite

(voir figure).

3. Attention à ce que le tuyau ne soit pas plié ou

écrasé.

 La pression de leau doit être comprise entre les

valeurs indiquées dans le tableau des Caractéristiques

techniques (voir page ci-contre).

 Si la longueur du tuyau dalimentation ne suffit pas,

sadresser à un magasin spécialisé ou à un technicien

agréé.

 Nutiliser que des tuyaux neufs.

 Utiliser ceux qui sont fournis avec lappareil.

Raccordement du tuyau de vidange

Raccordez le tuyau

d'évacuation, sans le

plier, à un conduit

d'évacuation ou à une

évacuation murale placés

à une distance du sol

comprise entre 65 et 100

cm;

ou bien accrochez-le à

un évier ou à une

baignoire, dans ce cas,

fixez le support en

plastique fourni avec

l'appareil au robinet (voir

figure). L'extrémité libre

du tuyau d'évacuation ne

doit pas être plongée

dans l'eau.

 L'utilisation de tuyaux de rallonge est absolument

déconseillée, si vous ne pouvez vraiment pas faire

autrement vous devrez utiliser un tuyau de même

diamètre et de longueur maximum de 150 cm.

Branchement électrique

Avant de brancher votre électroménager à la prise de

courant, contrôlez que:

 la prise est bien avec terre et conforme aux

réglementations applicables en la matière;

 la prise électrique est bien apte à supporter la

puissance maximum de l'électroménager figurant

sur la plaquette des caractéristiques (voir page 19);

 la tension d'alimentation est bien comprise entre

les valeurs figurant sur la plaquette des

caractéristiques (voir page 19);

 la prise est bien compatible avec la fiche du lave-

linge. Autrement, remplacez la prise ou la fiche.

Votre électroménager dispose à présent d'une fiche

moulée 13 ampères qui peut être branchée dans une

prise compatible pour utilisation immédiate. Veuillez

lire les instructions suivantes avant d'utiliser votre

électroménager.

ATTENTION - L'ELECTROMENAGER DOIT ETRE

RACCORDE A LA MASSE. LES OPERATIONS

DECRITES CI-APRES DOIVENT ETRE EFFECTUEES

PAR UN ELECTRICIEN QUALIFIE.

Remplacement du fusible:

En cas de remplacement d'un fusible défectueux, utilisez

toujours des fusibles de 13 ampères ASTA conformes au

standard BS1362 et remontez le couvercle du fusible. Si

vous avez perdu le couvercle du fusible, n'utilisez pas la

fiche tant que la pièce manquante n'aura pas été

remplacée.

Couvercles des fusibles:

Si vous remplacez le couvercle du fusible, veillez à ce que

sa couleur soit bien celle qui est indiquée par le code ou

l'indication colorée à la base de la fiche. Pour toute pièce

détachée, adressez-vous directement au centre

d'assistance technique le plus proche de chez vous.

Démontage de la fiche:

Si l'électroménager est équipé d'une fiche incorporée

qui ne peut pas être câblée à nouveau et s'il faut faire

passer le câble à travers des divisions, des unités,

etc. contrôlez que:

la fiche est bien remplacée par une autre câblable à

nouveau de 13 ampères portant la marque BSI

ou bien:

que le câble est bien raccordé directement à la prise

de 13 ampères, contrôlée par un interrupteur (confor-

me BS 5733) accessible sans qu'il faille déplacer

l'électroménager.

Elimination de la fiche:

Avant d'éliminer la fiche, rendez les broches

inutilisables de manière à ce que la fiche ne puisse

pas être branchée accidentellement dans une prise.

Instructions pour le raccordement du câble à une

fiche alternative:

Important: les couleurs des fils du câble de réseau

correspondent à la codification suivante:

Jaune/Vert Terre

Bleu Neutre

Marron Alimenté

Les couleurs des fils du câble pourraient ne pas

correspondre aux indications de couleur qui identifient

les broches de la fiche, procédez comme suit:

raccordez le fil jaune/vert à la borne repérée par la

lettre E ou

ou de couleur verte ou jaune/vert

raccordez le fil marron à la borne repérée par la lettre

L ou de couleur rouge

raccordez le fil bleu à la borne repérée par la lettre N

ou de couleur noire.

65 - 100 cm

En cas d'utilisation d'une fiche de 13 ampères (BS

1363), installez un fusible de 13 ampères dans la fiche

ou sur l'adaptateur ou sur la carte de distribution.

En cas de doute sur l'alimentation électrique de votre

électroménager, faites appel à un électricien qualifié

avant de le mettre en service.

Raccordement d'une fiche alternative:

les couleurs des fils du câble de réseau

correspondent à la codification suivante:

BLEU NEUTRE (N)

MARRON ALIMENTE (L)

JAUNE/VERT TERRE (E)

Elimination de l'électroménager:

Lors de la mise au rebus de l'électroménager,

débarrassez-le de sa fiche en coupant le câble

d'alimentation le plus près possible de cette dernière

et éliminez comme décrit précédemment.

 Votre lave-linge ne doit pas être installé dehors,

même à l'abri, car il est très dangereux de le laisser

exposé à la pluie et aux orages.

 Après installation du lave-linge, la prise de courant

doit être facilement accessible.

 N'utilisez ni rallonges ni prises multiples.

 Le câble ne doit être ni plié ni écrasé.

 Le câble d'alimentation ne doit être remplacé que

par des techniciens agréés.

Attention! Nous déclinons toute responsabilité en cas

de non respect des normes énumérées ci-dessus.

Premier cycle de lavage

Avant la première mise en service de lappareil,

effectuer un cycle de lavage avec un produit lessiviel

mais sans linge et sélectionner le programme 2.

GREEN &

YELLOW

BROWN

BLUE

13 ampere fuse

CROSS-BAR

CORD GRIP

Caractéristiques techniques

Modèle

IWDC 7125

Dimensions

largeur 59,5 cm

hauteur 85 cm

profondeur 53,5 cm

Capacité

de 1 à 7 kg pour le lavage;

de 1 à 5 kg pour le séchage

Raccordements

électriques

Voir la plaque signalétique appliquée

sur la machine

Raccordements

hydrauliques

pression maximale 1 MPa (10 bar)

pression minimale 0,05 MPa (0,5 bar)

capacité du tambour 52 litres

Vitesse

d'essorage

jusqu'à 1200 tours minute

Programmes de

contrôle selon la

norme EN 50229

lavage: programme 2; température

60°C; effectué avec une charge de 7 kg.

séchage: premier séchage effectué

avec 2 kg de charge et bouton

SECHAGE amené sur position .

deuxième séchage effectué avec 5 kg

de charge et bouton SECHAGE amené

sur position .

Cet appareil est conforme aux

Directives Communautaires suivantes:

- 89/336/CEE du 03/05/89

(Compatibilité électromagnétique) et

modifications suivantes

- 2002/96/CE

- 2006/95/CE (Basse Tension)

Tiroir à produits lessiviels: pour charger les

produits lessiviels et les additifs (voir Produits lessiviels

et linge).

Touche ON/OFF: pour allumer ou éteindre le lavante-

séchante.

Bouton PROGRAMMES: pour sélectionner les

programmes. Pendant le programme, le bouton ne

tournera pas.

Touches avec voyants FONCTION: pour sélectionner

les fonctions disponibles. Le voyant correspondant à

la fonction sélectionnée restera allumé.

Bouton TEMPÉRATURE: pour sélectionner la

température ou un lavage à froid (voir

Personnalisations).

Bouton SÉCHAGE: pour sélectionner le séchage

désiré (voir Personnalisations).

Voyants DÉROULEMENT CYCLE/DÉPART

DIFFÉRÉ: pour suivre le stade davancement du

programme de lavage.

Le voyant allumé indique la phase de lavage en

cours.

Si la fonction Départ différé (départ différé) a été

sélectionnée, ils indiquent le temps restant jusquau

démarrage du programme (voir page ci-contre).

Voyant HUBLOT VERROUILLÉ: indique si la porte

est verrouillée (voir page ci-contre).

Touche avec voyant START/PAUSE: pour démarrer

les programmes ou les interrompre momentanément.

N.B.: pour effectuer une pause du lavage en cours,

appuyer sur cette touche, le voyant correspondant se

mettra à clignoter en orange tandis que celui de la

phase en cours restera allumé fixe. Si le voyant

HUBLOT VERROUILLÉ

est éteint, on peut ouvrir la

porte.

Pour faire redémarrer le lavage exactement de

lendroit où il a été interrompu, appuyer une nouvelle

fois sur la touche.

Stand-by

Ce lavante-séchante, conformément aux nouvelles

normes en vigueur dans le domaine de l'économie

d'énergie, est équipée d'un système d'extinction

automatique (veille) activé après environ 30 minutes

d'inutilisation. Appuyez brièvement sur la touche ON/

OFF et attendre que la machine soit réactivée.

Description du lavante-séchante

et démarrage dun programme

Voyants

DÉROULEMENT

CYCLE/DÉPART DIFFÉRÉ

Voyant

HUBLOT

VERROUILLÉ

Touche avec

voyant

START/

PAUSE

Bandeau de commandes

Tiroir à produits lessiviels

Bouton

SÉCHAGE

Touches avec voyants

FONCTION

Touche

ON/OFF

Bouton

PROGRAMMES

Bouton

TEMPÉRATURE

La page est en cours de chargement...

Indesit IWDC 7125 B (EX)60HZ Mode d'emploi

Marque: Indesit

Modèle: IWDC 7125 B (EX)60HZ

Catégorie: Machines à laver

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Indesit IWDC 7125 B (EX)60HZ User guide

Indesit IWDC 7125 B (EX)60HZ Mode d'emploi

Indesit IWDC 7125 B (EX)60HZ Mode d'emploi

dans d''autres langues

Documents connexes