Indesit IWDC 7125 B (EX)60HZ Mode d'emploi

Catégorie
Machines à laver
Taper
Mode d'emploi
GB
1
Contents
Installation, 2-3-4-5
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Description of the washer-dryer and
starting a wash cycle, 6-7
Control panel
Indicator lights
Starting a wash cycle
Wash cycles, 8
Table of wash cycles
Personalisation, 9
Setting the temperature
Setting the drying cycle
Functions
Detergents and laundry, 10
Detergent dispenser drawer
Preparing the laundry
Garments requiring special care
Load balancing system
Precautions and tips, 11
General safety
Disposal
Opening the porthole door manually
Care and maintenance, 12
Cutting off the water or electricity supply
Cleaning the washer-dryer
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Troubleshooting, 13
Service, 14
IWDC 7125
Instructions for use
WASHER-DRYER
English,1
GB
Français,15
F
AR
, 29
This symbol reminds you to read this instruction manual.
2
GB
Installation
This instruction manual should be kept in a safe
place for future reference. If the washer-dryer is sold,
transferred or moved, make sure that the instruction
manual remains with the machine so that the new
owner is able to familiarise himself/herself with its
operation and features.
Read these instructions carefully: they contain vital
information relating to the safe installation and
operation of the appliance.
Unpacking and levelling
Unpacking
1. Remove the washer-dryer from its packaging.
2. Make sure that the washer-dryer has not been
damaged during the transportation process. If it has
been damaged, contact the retailer and do not
proceed any further with the installation process.
3. Remove the 4
protective screws (used
during transportation) and
the rubber washer with
the corresponding
spacer, located on the
rear part of the appliance
(see figure).
4. Close off the holes using the plastic plugs provided.
5. Keep all the parts in a safe place: you will need
them again if the washer-dryer needs to be moved to
another location.
Packaging materials should not be used as toys for
children.
Levelling
1. Install the washer-dryer on a flat sturdy floor,
without resting it up against walls, furniture cabinets
or anything else.
2. If the floor is not
perfectly level, compen-
sate for any unevenness
by tightening or loosening
the adjustable front feet
(see figure); the angle of
inclination, measured in
relation to the worktop,
must not exceed 2°.
Levelling the machine correctly will provide it with
stability, help to avoid vibrations and excessive noise
and prevent it from shifting while it is operating. If it is
placed on carpet or a rug, adjust the feet in such a
way as to allow a sufficient ventilation space
underneath the washer-dryer.
Connecting the electricity and water
supplies
Connecting the water inlet hose
1. Connect the supply
pipe by screwing it to a
cold water tab using a ¾
gas threaded connection
(see figure).
Before performing the
connection, allow the
water to run freely until it
is perfectly clear.
2. Connect the inlet hose
to the washer-dryer by
screwing it onto the
corresponding water inlet
of the appliance, which is
situated on the top right-
hand side of the rear part
of the appliance (see
figure).
3. Make sure that the hose is not folded over or bent.
The water pressure at the tap must fall within the
values indicated in the Technical details table (see
next page).
If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.
Never use second-hand hoses.
Use the ones supplied with the machine.
GB
3
Connecting the drain hose
Connect the drain hose,
without bending it, to a
draining duct or a wall
drain situated between
65 and 100 cm from the
floor;
alternatively, place it over
the edge of a basin, sink
or tub, fastening the
duct supplied to the tap
(see figure). The free end
of the hose should not
be underwater.
We advise against the use of hose extensions; in
case of absolute need, the extension must have the
same diameter as the original hose and must not
exceed 150 cm in length.
Electric connection
Before plugging the appliance into the mains socket,
make sure that:
the socket is earthed and in compliance with the
applicable law;
the socket is able to sustain the appliance's
maximum power load indicated in the Technical
details table (see page 5);
the supply voltage is included within the values i
ndicated on the Technical details table
(see page 5);
the socket is compatible with the washing
machine's plug. If this is not the case, replace
the socket or the plug.
Your appliance is now supplied with a 13 amp fused
plug it can be plugged into a 13 amp socket for
immediate use. Before using the appliance please
read the instructions below.
WARNING - THIS APPLIANCE MUST BE EARTHED.
THE FOLLOWING OPERATIONS SHOULD BE
CARRIED OUT BY A QUALIFIED ELECTRICIAN.
Replacing the fuse:
When replacing a faulty fuse, a 13 amp ASTA
approved fuse to BS 1362 should always be used,
and the fuse cover re-fitted. If the fuse cover is lost,
the plug must not be used until a replacement is
obtained.
Replacement fuse covers:
If a replacement fuse cover is fitted, it must be of the
correct colour as indicated by the coloured marking
or the colour that is embossed in words on the base
of the plug. Replacements can be obtained directly
from your nearest Service Depot.
Removing the plug:
If your appliance has a non-rewireable moulded plug
and you should wish to re-route the mains cable
through partitions, units etc., please ensure that
either:
the plug is replaced by a fused 13 ampere re-
wearable plug bearing the BSI mark of approval.
or:
the mains cable is wired directly into a 13 amp cable
outlet, controlled by a switch, (in compliance with BS
5733) which is accessible without moving the
appliance.
Disposing of the plug:
Ensure that before disposing of the plug itself, you
make the pins unusable so that it cannot be
accidentally inserted into a socket.
Instructions for connecting cable to an alternative plug:
Important: the wires in the mains lead are coloured in
accordance with the following code:
Green & Yellow Earth
Blue Neutral
Brown Live
As the colours of the wires in the lead may not
correspond with the coloured markings identifyng the
terminals in your plug, proceed as follows:
Connect Green & Yellow wire to terminal marked E or
or coloured Green or Green & Yellow.
Connect Brown wire to terminal marked L or
coloured Red.
Connect Blue wire to terminal marked N or coloured
Black.
65 - 100 cm
4
GB
If a 13 amp plug (BS 1363) is used it must be fitted
with a
13 amp fuse, either in the plug or adaptor or at the
distribution board.
If you are in any doubt the electrical supply to your
machine, consult a qualified electrician before use.
How to connect an alternative plug:
The wires in this mains lead are coloured in
accordance with the following code:
BLUE NEUTRAL (N)
BROWN LIVE (L)
GREEN & YELLOW EARTH (E)
Disposing of the appliance:
When disposing of the appliance please remove the
plug by cutting the mains cable as close as possible
to the plug body and dispose of it as described above.
The washing machine should not be installed in an
outdoor environment, not even when the area is
sheltered, because it may be very dangerous to leave
it exposed to rain and thunderstorms.
When the washing machine is installed, the mains
socket must be within easy reach.
Do not use extensions or multiple sockets.
The power supply cable must never be bent or
dangerously compressed.
The power supply cable must only be replaced by
an authorised serviceman.
Warning! The company denies all liability if and when
these norms are not respected.
GREEN &
YELLOW
BROWN
BLUE
13 ampere fuse
CROSS-BAR
CORD GRIP
The first wash cycle
Once the appliance has been installed, and before
you use it for the first time, run a wash cycle with
detergent and no laundry, using the wash cycle 2.
GB
5
Technical data
Model
IWDC 7125
Dimensions
width 59.5 cm
height 85 cm
depth 53,5 cm
Capacity
from 1 to 7 kg for the wash programme;
from 1 to 5 kg for the drying programme
Electrical
connections
please refer to the technical data plate fixed
to the machine
Wate r
connections
maximum pressure 1 MPa (10 bar)
minimum pressure 0.05 MPa (0.5 bar)
drum capacity 52 litres
Spin speed
up to 1200 rotations per minute
Energy
rated
programmes
according to
regulation
EN 50229
Wash: programme 2; temperature 60°C;
run with a load of 7 kg.
Drying: first drying cycle performed with a 2 kg
load and the DRYING knob on the setting;
Second drying cycle performed with a 5 kg
load and the DRYING knob on the setting.
This appliance conforms to the following
EC Directives:
- 89/336/EEC dated 03/05/89
(Electromagnetic Compatibility) and
subsequent modifications
- 2002/96/EC
- 2006/95/EC Low Voltage)
6
GB
Detergent dispenser drawer: used to dispense
detergents and washing additives (see Detergents
and laundry).
ON/OFF button: switches the washer-dryer on and
off.
WASH CYCLE knob: programmes the wash cycles.
During the wash cycle, the knob does not move.
FUNCTION buttons with indicator light: used to
select the available functions. The indicator light
corresponding to the selected function will remain lit.
TEMPERATURE knob: sets the temperature or the
cold wash cycle (see Personalisation).
DRYING knob: used to set the desired drying
programme (see Personalisation).
WASH CYCLE PROGRESS/DELAY TIMER
indicator light
s: used to monitor the progress of the
wash cycle.
The illuminated indicator light shows which phase is in
progress.
If the Delay Timer function has been set, the time
remaining until the wash cycle starts will be indicated
(see next page).
DOOR LOCKED indicator light: indicates whether
the door may be opened or not (see next page).
START/PAUSE button with indicator light: starts or
temporarily interrupts the wash cycles.
N.B. To pause the wash cycle in progress, press this
button; the corresponding indicator light will flash
orange, while the indicator light for the current wash
cycle phase will remain lit in a fixed manner. If the
DOOR LOCKED
indicator light is switched off, the
door may be opened.
To start the wash cycle from the point at which it was
interrupted, press this button again.
Standby mode
This washing machine, in compliance with new
energy saving regulations, is fitted with an automatic
standby system which is enabled after about 30
minutes if no activity is detected. Press the ON-OFF
button briefly and wait for the machine to start up
again.
Description of the washer-dryer and
starting a wash cycle
WASH CYCLE PROGRESS/
DELAY TIMER
indicator lights
DOOR LOCKED
indicator light
START/
PAUSE
button with
indicator light
Control panel
Detergent dispenser drawer
ON/OFF
button
WASH CYCLE
knob
TEMPERATURE
knob
FUNCTION
buttons with
indicator lights
DRYING
knob
GB
7
Indicator lights
The indicator lights provide important information.
This is what they can tell you:
Delayed start
If the DELAY TIMER function has been activated (see
Personalisation), after the wash cycle has been
started the indicator light corresponding to the
selected delay period will begin to flash:
As time passes, the remaining delay will be displayed
and the corresponding indicator light will flash:
The set programme will start once the selected time
delay has expired.
Wash cycle phase indicator lights
Once the desired wash cycle has been selected and has
begun, the indicator lights switch on one by one to
indicate which phase of the cycle is currently in progress.
Note: when the drying cycle has finished, the
DRYING knob should be returned to the 0position.
Function buttons and corresponding indicator lights
When a function is selected, the corresponding
indicator light will illuminate.
If the selected function is not compatible with the
programmed wash cycle, the corresponding indicator
light will flash and the function will not be activated.
If the selected function is not compatible with another
function which has been selected previously, the
indicator light corresponding to the first function
selected will flash and only the second function will be
activated; the indicator light corresponding to the
enabled option will remain lit.
Door locked indicator light
When the indicator light is on, the porthole door is
locked to prevent it from being opened; make sure
the indicator light is off before opening the door. To
open the door during a running wash cycle, press the
START/PAUSE button; the door may be opened once
the DOOR LOCKED indicator light turns off.
Starting a wash cycle
1. Switch the washer-dryer on by pressing the ON/OFF button. All indicator lights will switch on for a few
seconds, then they will switch off and the START/PAUSE indicator light will pulse.
2. Load the laundry and close the door.
3. Set the WASH CYCLE knob to the desired programme.
4. Set the washing temperature (see Personalisation).
5. Set the drying cycle if necessary (see Personalisation).
6. Measure out the detergent and washing additives (see Detergents and laundry).
7. Select the desired functions.
8. Start the wash cycle by pressing the START/PAUSE button and the corresponding indicator light will remain lit
in a fixed manner, in green.
To cancel the set wash cycle, pause the machine by pressing the START/PAUSE button and select a new cycle.
9. At the end of the wash cycle the
indicator light will switch on. The door can be opened once the DOOR
LOCKED
indicator light turns off. Take out your laundry and leave the appliance door ajar to make sure the
drum dries completely. Switch the washer-dryer off by pressing the ON/OFF button.
Wash
Rinse
Spin/Drain
Drying
End of wash cycle
8
GB
Specials wash cycles
Sport Light (
wash cycle
9) is for washing lightly soiled sports clothing fabrics (tracksuits, shorts, etc.); for best
results, we recommend not exceeding the maximum load indicated in the "Table of wash cycles". We recommend
using a liquid detergent and dosage suitable for a half-load.
Sport Shoes (
wash cycle
10) is for washing sports shoes; for best results, do not wash more than 2 pairs
simultaneously.
Express Wash & Dry (
wash cycle
13) was designed to wash and dry lightly soiled garments quickly. This cycle may
be used to wash and dry a laundry load of up to 0.5 kg in just 35 minutes.
To achieve optimum results, use liquid detergent and pre-treat cuffs, collars and stains.
Wash cycles
The information contained in the table is intended as a guide only.
For all Test Institutes:
1) Test wash cycle in compliance with regulation EN 50229: set wash cycle 2 with a temperature of 60°C.
2) Long wash cycle for cottons: set wash cycle 2 with a temperature of 40°C.
3) Short wash cycle for cottons: set wash cycle 4 with a temperature of 40°C.
Wash cycles
Table of wash cycles
Description of the wash cycle
Max
.
temp.
(°C)
Max.
speed
(rpm)
Drying
Detergents
Max. load
(kg)
Cycle
duration
Pre-
wash
Wash
Fabric
softener
Normal
Eco
Time
Normal
Eco
Time
Daily
1
Cotton with prewash:
extremely soiled whites.
90° 1200
lll l
7
-
171
-
2
Cotton:
extremely soiled whites.
90° 1200
l
-
ll
7
-
155
-
2
Cotton (1):
heavily soiled whites and resistant colours.
60° 1200
l
-
ll
7
-
153
-
2
Cotton (2):
heavily soiled whites and delicate colours.
40° 1200
l
-
ll
7
-
147
-
3
Cotton:
heavily soiled whites and resistant colours.
60° 1200
l
-
ll
73,5130104
4
Coloured Cottons (3):
lightly soiled whites and delicate colours.
40° 1200
l
-
ll
73,59271
5
Synthetics:
heavily soiled resistant colours.
60° 800
l
-
ll
328572
Special
6
Wool:
for wool, cashmere, etc.
40° 600
- -
ll
1,5
-
55
-
7
Silk/Curtains:
for garments in silk and viscose, lingerie.
30° 0
- -
ll
1
-
55
-
8
Jeans
40° 800
l
-
ll
3
-
80
-
9
Sport Light
30° 600
- -
ll
3
-
68
-
10
Sport Shoes
30° 600
- -
ll
Max. 2
pairs
-
50
-
Drying
11
Cotton dry
- -
l
- - -
5
- - -
12
Synthetics dry
- -
l
- - -
3
- - -
13
Express Wash & Dry
30° 1200
l
-
ll
0,5
-
35
-
Partial wash cycles
Rinse
-
1200
l
- -
l
7
-
36
-
Spin
-
1200
l
- - -
7
-
16
-
Drain
-
0
- - - -
7
-
2
-
GB
9
Setting the temperature
Turn the TEMPERATURE knob to set the wash temperature (see Table of wash cycles).
The temperature may be lowered, or even set to a cold wash
. The washer-dryer will automatically prevent you
from selecting a temperature which is higher than the maximum value set for each wash cycle.
Setting the drying cycle
Turn the DRYING knob to select the desired drying
option. There are two options:
A - Based on time: From 40 minutes to 180.
B - Based on the desired laundry dryness level:
Iron dry
: suitable for clothes which will need ironing
afterwards. the remaining dampness softens creases,
making them easier to remove.
Hanger dry
: ideal for clothes which do not need to
be dried fully.
Cupboard dry
: suitable for laundry which can be put back in a cupboard without being ironed.
If your laundry load to be washed and dried is much greater than the maximum stated load (see adjacent table),
perform the wash cycle, and when the cycle is complete, divide the garments into groups and put some of them back
in the drum. At this point, follow the instructions provided for a "Drying only" cycle. Repeat this procedure for the
remainder of the load.
Drying only
Use the cycle selector knob to select a drying cycle (11-12) in accordance with the type of fabric. The desired drying
level or time may also be set using the DRYING knob.
Functions
The various wash functions available with this washer-dryer will help to achieve the desired results, every time.
To activate the functions:
1. Press the button corresponding to the desired function;
2. the function is enabled when the corresponding indicator light is illuminated.
Note: If the indicator light flashes rapidly, this signals that this particular function may not be selected in
conjunction with the selected wash cycle.
Selecting this option enables you to suitably adjust drum rotation, temperature and water to a reduced load of lightly
soiled cotton and synthetic fabrics (refer to the
"Table of wash cycles"
). enables you to wash in less time
thereby saving water and electricity. We suggest using a liquid detergent suitably measured out to the load quantity.
This function may not be used in conjunction with cycles 1, 2, 6, 7, 8, 9, 10, 11, 12, 13, , , .
1200-600
Press this button to reduce the spin speed.
This function may not be used in conjunction with cycles 7, 11, 12, 13, .
Easy iron
By selecting this function, the wash and spin cycles will be modified in order to reduce the formation of creases. At
the end of the cycle the Washer-dryer will perform slow rotations of the drum; the indicator lights for the EASY
IRON and START/PAUSE options will flash (the first one green, the second orange) and the "END" indicator light
turns on. To end the cycle, press the START/PAUSE button or the EASY IRON button.
For the 7 wash cycle, the machine will end the cycle while the laundry is soaking and the EASY IRON and START/
PAUSE indicator lights will flash. To drain the water so that the laundry may be removed, press the START/PAUSE
button or the EASY IRON button.
This function may not be used in conjunction with cycles 6, 9, 10, 11, 12, 13,
, .
Note: If you also want to run the drying cycle, this option is enabled only if combined with level
(Iron dry).
Delay timer
This timer delays the start time of the wash cycle by up to 9 hours. Press the button repeatedly until the indicator light
corresponding to the desired delay time switches on. The fourth time the button is pressed, the function will be disabled.
N.B. Once the START/PAUSE button has been pressed, the delay time can only be modified by decreasing it until launching
the set programme.
This option is enabled with all programmes.
Personalisation
Fabric
type
Load type Max.
load
(kg)
Cupboard
dry
Hanger
dry
Iron
dry
Cotton Clothing of different
sizes, Terry towels
5180170140
Synthetics Sheets, Shirts, Pyjamas,
socks, etc.
3 140 120 100
Table of Drying times (guideline values)
10
GB
Detergents and laundry
Detergent dispenser drawer
Good washing results also depend on the correct
dose of detergent: adding too much detergent will not
necessarily result in a more efficient wash, and may in
fact cause build up on the inside of your appliance
and contribute to environmental pollution.
Do not use hand washing detergents because these
create too much foam.
Open the detergent
dispenser drawer and
pour in the detergent or
washing additive, as
follows.
compartment 1: Pre-wash detergent (powder)
compartment 2: Detergent for the wash cycle
(powder or liquid)
Liquid detergent should only be poured in immediately
prior to the start of the wash cycle.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid.
Preparing the laundry
Divide the laundry according to:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from
whites.
Empty all garment pockets and check the buttons.
Do not exceed the listed values, which refer to the
weight of the laundry when dry:
Durable fabrics: max. 7 kg
Synthetic fabrics: max. 3 kg
Delicate fabrics: max. 2 kg
Wool: max. 1,5 kg
Silk: max. 1 kg
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1200 g
1 towel 150-250 g
Garments requiring special care
Wool: all wool garments can be washed using
programme 6, even those carrying the "hand-wash
only"
label. For best results, use special
detergents and do not exceed 1,5 kg of laundry.
1
2
3
Silk: use special wash cycle 7 to wash all silk
garments. We recommend the use of special
detergent which has been designed to wash delicate
clothes.
Curtains: fold curtains and place them in a pillow
case or mesh bag. Use wash cycle 7.
Jeans: Turn garments inside-out before washing and
use a liquid detergent. Use programme 8.
Load balancing system
Before every spin cycle, to avoid excessive vibrations
and to distribute the load in a uniform manner, the
drum rotates continuously at a speed which is slightly
greater than the washing rotation speed. If, after
several attempts, the load is not balanced correctly,
the machine spins at a reduced spin speed. If the
load is excessively unbalanced, the washer-dryer
performs the distribution process instead of spinning.
To encourage improved load distribution and balance,
we recommend small and large garments are mixed
in the load.
GB
11
Precautions and tips
This washer-dryer was designed and constructed in
accordance with international safety regulations. The following
information is provided for safety reasons and must therefore
be read carefully.
General safety
This appliance was designed for domestic use only.
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their
safety. Children should be supervised to ensure that they
do not play with the appliance.
Do not dry unwashed items in the tumble dryer.
Items that have been soiled with substances such as
cooking oil, acetone, alcohol, petrol, kerosene, spot
removers, turpentine, waxes and wax removers should be
washed in hot water with an extra amount of detergent
before being dried in the tumble dryer.
Items such as foam rubber (latex foam), shower caps,
waterproof textiles, rubber backed articles and clothes or
pillows fitted with foam rubber pads should not be dried in
the tumble dryer.
Fabric softeners, or similar products, should be used as
specified by the fabric softener instructions.
The final part of a tumble dryer cycle occurs without heat
(cool down cycle) to ensure that the items are left at a
temperature that ensures that the items will not be
damaged.
WARNING: Never stop a tumble dryer before the end of the
drying cycle unless all items are quickly removed and
spread out so that the heat is dissipated.
Do not touch the machine when barefoot or with wet or
damp hands or feet.
Do not pull on the power supply cable when unplugging the
appliance from the electricity socket. Hold the plug and pull.
Do not open the detergent dispenser drawer while the
machine is in operation.
Do not touch the drained water as it may reach extremely
high temperatures.
Never force the porthole door. This could damage the
safety lock mechanism designed to prevent accidental
opening.
If the appliance breaks down, do not under any
circumstances access the internal mechanisms in an
attempt to repair it yourself.
Always keep children well away from the appliance while it is
operating.
The door can become quite hot during the wash cycle.
If the appliance has to be moved, work in a group of two or
three people and handle it with the utmost care. Never try
to do this alone, because the appliance is very heavy.
Before loading laundry into the washer-dryer, make sure the
drum is empty.
During the drying phase, the door tends to get
quite hot.
Do not use the appliance to dry clothes that have
been washed with flammable solvents (e.g.
trichlorethylene).
Do not use the appliance to dry foam rubber or
similar elastomers.
Make sure that the water tap is turned on during
the drying cycles.
Disposal
 Disposing of the packaging materials:
observe local regulations so that the packaging may be re-
used.
 The European Directive 2002/96/EC relating to Waste
Electrical and Electronic Equipment (WEEE) states that
household appliances should not be disposed of using the
normal solid urban waste cycle. Exhausted appliances
should be collected separately in order to optimise the cost
of re-using and recycling the materials inside the machine,
while preventing potential damage to the atmosphere and
to public health. The crossed-out dustbin is marked on all
products to remind the owner of their obligations regarding
separated waste collection.
For more information relating to the correct disposal of
household appliances, owners should contact their local
authorities or appliance dealer.
Opening the porthole door manually
In the event that it is not possible to open the porthole
door due to a powercut, and if you wish to remove the
laundry, proceed as follows:
1. remove the plug from the electrical socket.
2. make sure the water level inside the machine is lower
than the door opening; if it is not, remove excess water
using the drain hose, collecting it in a bucket as indicated in
the figure.
3. using a screwdriver, remove the cover panel on the
lower front part of the washing machine (see figure).
4. pull outwards using the tab as indicated in the figure,
until the plastic tie-rod is freed from its stop position; pull
downwards and open the door at the same time.
5. reposition the panel, making sure the hooks are securely
in place before you push it onto the appliance.
20
12
GB
Care and maintenance
Cutting off the water and electricity
supplies
Turn off the water tap after every wash cycle. This
will limit wear on the hydraulic system inside the
washer-dryer and help to prevent leaks.
Unplug the washer-dryer when cleaning it and
during all maintenance work.
Cleaning the washer-dryer
The outer parts and rubber components of the
appliance can be cleaned using a soft cloth soaked
in lukewarm soapy water. Do not use solvents or
abrasives.
Cleaning the detergent dispenser
drawer
Remove the dispenser
by raising it and pulling it
out (see figure).
Wash it under running
water; this operation
should be repeated
frequently.
Caring for the door and drum of your
appliance
Always leave the porthole door ajar in order to
prevent unpleasant odours from forming.
Cleaning the pump
The washer-dryer is fitted with a self-cleaning pump
which does not require any maintenance. Sometimes,
small items (such as coins or buttons) may fall into the
pre-chamber which protects the pump, situated in its
bottom part.
Make sure the wash cycle has finished and unplug
the appliance.
To access the pre-chamber:
1. using a screwdriver,
remove the cover panel
on the lower front part of
the washer-dryer (see
figure);
2. unscrew the lid by
rotating it anti-clockwise
(see figure): a little water
may trickle out. This is
perfectly normal;
3. clean the inside thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks are
securely in place before you push it onto the
appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If there are
any cracks, it should be replaced immediately: during
the wash cycles, water pressure is very strong and a
cracked hose could easily split open.
Never use second-hand hoses.
GB
13
Troubleshooting
Your washer-dryer could fail to work. Before contacting the Technical Assistance Centre (see Assistance), make
sure that the problem cannot be not solved easily using the following list.
Problem:
The Washer-dryer does not
switch on.
The wash cycle does not start.
The Washer-dryer does not take
in water (the indicator light for
the first wash cycle stage
flashes rapidly).
The Washer-dryer continuously
takes in and
drains water.
The Washer-dryer does not drain
or spin.
The Washer-dryer vibrates a lot
during the spin cycle.
The Washer-dryer leaks.
The "functions" indicator lights and the
"start/pause" indicator light flash, while
one of the "phase in progress" indicator
lights and the "door locked" indicator
light will remain lit in a fixed manner.
There is too much foam.
The washer-dryer does not dry.
Possible causes / Solutions:
The appliance is not plugged into the socket fully, or is not making contact.
There is no power in the house.
The Washer-dryer door is not closed properly.
The ON/OFF button has not been pressed.
The START/PAUSE button has not been pressed.
The water tap has not been opened.
A delayed start has been set.
The water inlet hose is not connected to the tap.
The hose is bent.
The water tap has not been opened.
There is no water supply in the house.
The pressure is too low.
The START/PAUSE button has not been pressed.
The drain hose is not fitted at a height between 65 and 100 cm from
the floor (see Installation).
The free end of the hose is under water (see Installation).
The wall drainage system is not fitted with a breather pipe.
If the problem persists even after these checks, turn off the water tap, switch
the appliance off and contact the Assistance Service. If the dwelling is on one of
the upper floors of a building, there may be problems relating to water drainage,
causing the Washer-dryer to fill with water and drain continuously. Special anti-
draining valves are available in shops and help to avoid this inconvenience.
The wash cycle does not include draining: some wash cycles require the
drain phase to be started manually.
The Easy iron option has been activated: To complete the wash cycle,
press the START/PAUSE button (see Wash cycles and options).
The drain hose is bent (see Installation).
The drainage duct is clogged.
The drum was not unlocked correctly during installation (see Installation).
The Washer-dryer is not level (see Installation).
The Washer-dryer is trapped between cabinets and walls (see Installation).
The water inlet hose is not screwed on properly (see Installation).
The detergent dispenser drawer is blocked (for cleaning instructions, see Care
and maintenance).
The drain hose is not fixed properly (see Installation).
Switch off the machine and unplug it, wait for approximately 1 minute
and then switch it back on again.
If the problem persists, contact the Technical Assistance Service.
The detergent is not suitable for machine washing (it should display the
text for Washer-dryers or hand and machine wash, or the like).
Too much detergent was used.
The appliance is not plugged into the socket, or not enough to make contact.
There has been a power failure.
The appliance door is not shut properly.
A delayed start has been set.
DRYING knob is in the 0 position.
14
GB
Service
Before calling for Assistance:
Check whether you can solve the problem alone (see Troubleshooting);
Restart the programme to check whether the problem has been solved;
If this is not the case, contact an authorised Technical Assistance Centre using the telephone number
provided on the guarantee certificate.
Always request the assistance of authorised technicians.
Have the following information to hand:
the type of problem;
the appliance model (Mod.);
the serial number (S/N).
This information can be found on the data plate applied to the rear of the washer-dryer, and can also be
found on the front of the appliance by opening the door.
FR
15
Français
Sommaire
Installation, 16-17-18-19
Déballage et mise à niveau
Raccordements eau et électricité
Premier cycle de lavage
Caractéristiques techniques
Description du lavante-séchante et
démarrage dun programme, 20-21
Bandeau de commandes
Voyants
Démarrage dun programme
Programmes, 22
Tableau des programmes
Personnalisations, 23
Sélection de la température
Sélectionner le séchage
Fonctions
Produits lessiviels et linge, 24
Tiroir à produits lessiviels
Triage du linge
Linge ou vêtements particuliers
Système déquilibrage de la charge
Précautions et conseils, 25
Sécurité générale
Mise au rebut
Ouverture manuelle de la porte hublot
Entretien et soin, 26
Coupure de larrivée deau et du courant
Nettoyage du lavante-séchante
Nettoyage du tiroir à produits lessiviels.
Entretien du hublot et du tambour
Nettoyage de la pompe
Contrôle du tuyau darrivée de leau
Anomalies et remèdes, 27
Assistance, 28
FR
IWDC 7125
Mode demploi
LAVANTE-SÉCHANTE
! Ce symbole vous rappelle de lire ce mode d'emploi.
16
FR
Installation
Conserver ce mode demploi pour pouvoir le
consulter à tout moment. En cas de vente, de
cession ou de déménagement, veiller à ce quil suive
toujours le lavante-séchante pour que son nouveau
propriétaire soit informé sur son mode de
fonctionnement et puisse profiter des conseils
correspondants.
Lire attentivement les instructions: elles fournissent
des conseils importants sur linstallation, lutilisation et
la sécurité de lappareil.
Déballage et mise à niveau
Déballage
1. Déballer le lavante-séchante.
2. Contrôler que le lavante-séchante na pas été
endommagé pendant le transport. Sil est abîmé, ne
pas le raccorder et contacter le vendeur.
3. Enlever les 4 vis de
protection servant au
transport, le caoutchouc
et la cale, placés dans la
partie arrière (voir figure).
4. Boucher les trous à laide des bouchons plastique
fournis.
5. Conserver toutes ces pièces: il faudra les remonter
en cas de transport du lavante-séchante.
Les pièces demballage ne sont pas des jouets pour
enfants.
Mise à niveau
1. Installer le lavante-séchante sur un sol plat et
rigide, sans lappuyer contre des murs, des meubles
ou autre.
2. Si le sol nest pas
parfaitement horizontal,
visser ou dévisser les
pieds de réglage avant
(voir figure) pour niveler
lappareil; son angle
dinclinaison, mesuré sur
le plan de travail, ne doit
pas dépasser 2°.
Une bonne mise à niveau garantit la stabilité de
lappareil et évite quil y ait des vibrations, du bruit et
des déplacements en cours de fonctionnement. Si la
machine est posée sur de la moquette ou un tapis,
régler les pieds de manière à ce quil y ait
suffisamment despace pour assurer une bonne
ventilation.
Raccordements eau et électricité
Raccordement du tuyau darrivée de leau
1. Reliez le tuyau
d'alimentation en le
vissant à un robinet d'eau
froide à embout fileté 3/4
gaz (voir figure).
Faire couler leau jusquà
ce quelle soit limpide et
sans impuretés avant de
raccorder.
2. Raccorder le tuyau
darrivée de leau au
lavante-séchante en le
vissant à la prise deau
prévue, dans la partie
arrière en haut à droite
(voir figure).
3. Attention à ce que le tuyau ne soit pas plié ou
écrasé.
La pression de leau doit être comprise entre les
valeurs indiquées dans le tableau des Caractéristiques
techniques (voir page ci-contre).
Si la longueur du tuyau dalimentation ne suffit pas,
sadresser à un magasin spécialisé ou à un technicien
agréé.
Nutiliser que des tuyaux neufs.
Utiliser ceux qui sont fournis avec lappareil.
FR
17
Raccordement du tuyau de vidange
Raccordez le tuyau
d'évacuation, sans le
plier, à un conduit
d'évacuation ou à une
évacuation murale placés
à une distance du sol
comprise entre 65 et 100
cm;
ou bien accrochez-le à
un évier ou à une
baignoire, dans ce cas,
fixez le support en
plastique fourni avec
l'appareil au robinet (voir
figure). L'extrémité libre
du tuyau d'évacuation ne
doit pas être plongée
dans l'eau.
L'utilisation de tuyaux de rallonge est absolument
déconseillée, si vous ne pouvez vraiment pas faire
autrement vous devrez utiliser un tuyau de même
diamètre et de longueur maximum de 150 cm.
Branchement électrique
Avant de brancher votre électroménager à la prise de
courant, contrôlez que:
la prise est bien avec terre et conforme aux
réglementations applicables en la matière;
la prise électrique est bien apte à supporter la
puissance maximum de l'électroménager figurant
sur la plaquette des caractéristiques (voir page 19);
la tension d'alimentation est bien comprise entre
les valeurs figurant sur la plaquette des
caractéristiques (voir page 19);
la prise est bien compatible avec la fiche du lave-
linge. Autrement, remplacez la prise ou la fiche.
Votre électroménager dispose à présent d'une fiche
moulée 13 ampères qui peut être branchée dans une
prise compatible pour utilisation immédiate. Veuillez
lire les instructions suivantes avant d'utiliser votre
électroménager.
ATTENTION - L'ELECTROMENAGER DOIT ETRE
RACCORDE A LA MASSE. LES OPERATIONS
DECRITES CI-APRES DOIVENT ETRE EFFECTUEES
PAR UN ELECTRICIEN QUALIFIE.
Remplacement du fusible:
En cas de remplacement d'un fusible défectueux, utilisez
toujours des fusibles de 13 ampères ASTA conformes au
standard BS1362 et remontez le couvercle du fusible. Si
vous avez perdu le couvercle du fusible, n'utilisez pas la
fiche tant que la pièce manquante n'aura pas été
remplacée.
Couvercles des fusibles:
Si vous remplacez le couvercle du fusible, veillez à ce que
sa couleur soit bien celle qui est indiquée par le code ou
l'indication colorée à la base de la fiche. Pour toute pièce
détachée, adressez-vous directement au centre
d'assistance technique le plus proche de chez vous.
Démontage de la fiche:
Si l'électroménager est équipé d'une fiche incorporée
qui ne peut pas être câblée à nouveau et s'il faut faire
passer le câble à travers des divisions, des unités,
etc. contrôlez que:
la fiche est bien remplacée par une autre câblable à
nouveau de 13 ampères portant la marque BSI
ou bien:
que le câble est bien raccordé directement à la prise
de 13 ampères, contrôlée par un interrupteur (confor-
me BS 5733) accessible sans qu'il faille déplacer
l'électroménager.
Elimination de la fiche:
Avant d'éliminer la fiche, rendez les broches
inutilisables de manière à ce que la fiche ne puisse
pas être branchée accidentellement dans une prise.
Instructions pour le raccordement du câble à une
fiche alternative:
Important: les couleurs des fils du câble de réseau
correspondent à la codification suivante:
Jaune/Vert Terre
Bleu Neutre
Marron Alimenté
Les couleurs des fils du câble pourraient ne pas
correspondre aux indications de couleur qui identifient
les broches de la fiche, procédez comme suit:
raccordez le fil jaune/vert à la borne repérée par la
lettre E ou
ou de couleur verte ou jaune/vert
raccordez le fil marron à la borne repérée par la lettre
L ou de couleur rouge
raccordez le fil bleu à la borne repérée par la lettre N
ou de couleur noire.
65 - 100 cm
18
FR
En cas d'utilisation d'une fiche de 13 ampères (BS
1363), installez un fusible de 13 ampères dans la fiche
ou sur l'adaptateur ou sur la carte de distribution.
En cas de doute sur l'alimentation électrique de votre
électroménager, faites appel à un électricien qualifié
avant de le mettre en service.
Raccordement d'une fiche alternative:
les couleurs des fils du câble de réseau
correspondent à la codification suivante:
BLEU NEUTRE (N)
MARRON ALIMENTE (L)
JAUNE/VERT TERRE (E)
Elimination de l'électroménager:
Lors de la mise au rebus de l'électroménager,
débarrassez-le de sa fiche en coupant le câble
d'alimentation le plus près possible de cette dernière
et éliminez comme décrit précédemment.
Votre lave-linge ne doit pas être installé dehors,
même à l'abri, car il est très dangereux de le laisser
exposé à la pluie et aux orages.
Après installation du lave-linge, la prise de courant
doit être facilement accessible.
N'utilisez ni rallonges ni prises multiples.
Le câble ne doit être ni plié ni écrasé.
Le câble d'alimentation ne doit être remplacé que
par des techniciens agréés.
Attention! Nous déclinons toute responsabilité en cas
de non respect des normes énumérées ci-dessus.
Premier cycle de lavage
Avant la première mise en service de lappareil,
effectuer un cycle de lavage avec un produit lessiviel
mais sans linge et sélectionner le programme 2.
GREEN &
YELLOW
BROWN
BLUE
13 ampere fuse
CROSS-BAR
CORD GRIP
FR
19
Caractéristiques techniques
Modèle
IWDC 7125
Dimensions
largeur 59,5 cm
hauteur 85 cm
profondeur 53,5 cm
Capaci
de 1 à 7 kg pour le lavage;
de 1 à 5 kg pour le séchage
Raccordements
électriques
Voir la plaque signalétique appliquée
sur la machine
Raccordements
hydrauliques
pression maximale 1 MPa (10 bar)
pression minimale 0,05 MPa (0,5 bar)
capacité du tambour 52 litres
Vitesse
d'essorage
jusqu 1200 tours minute
Programmes de
contrôle selon la
norme EN 50229
lavage: programme 2; température
60°C; effectué avec une charge de 7 kg.
séchage: premierchage effectué
avec 2 kg de charge et bouton
SECHAGE ame sur position .
deuxième séchage effectué avec 5 kg
de charge et bouton SECHAGE ame
sur position .
Cet appareil est conforme aux
Directives Communautaires suivantes:
- 89/336/CEE du 03/05/89
(Compatibiliélectromagnétique) et
modifications suivantes
- 2002/96/CE
- 2006/95/CE (Basse Tension)
20
FR
Tiroir à produits lessiviels: pour charger les
produits lessiviels et les additifs (voir Produits lessiviels
et linge).
Touche ON/OFF: pour allumer ou éteindre le lavante-
séchante.
Bouton PROGRAMMES: pour sélectionner les
programmes. Pendant le programme, le bouton ne
tournera pas.
Touches avec voyants FONCTION: pour sélectionner
les fonctions disponibles. Le voyant correspondant à
la fonction sélectionnée restera allumé.
Bouton TEMPÉRATURE: pour sélectionner la
température ou un lavage à froid (voir
Personnalisations).
Bouton SÉCHAGE: pour sélectionner le séchage
désiré (voir Personnalisations).
Voyants DÉROULEMENT CYCLE/DÉPART
DIFFÉRÉ: pour suivre le stade davancement du
programme de lavage.
Le voyant allumé indique la phase de lavage en
cours.
Si la fonction Départ différé (départ différé) a été
sélectionnée, ils indiquent le temps restant jusquau
démarrage du programme (voir page ci-contre).
Voyant HUBLOT VERROUILLÉ: indique si la porte
est verrouillée (voir page ci-contre).
Touche avec voyant START/PAUSE: pour démarrer
les programmes ou les interrompre momentanément.
N.B.: pour effectuer une pause du lavage en cours,
appuyer sur cette touche, le voyant correspondant se
mettra à clignoter en orange tandis que celui de la
phase en cours restera allumé fixe. Si le voyant
HUBLOT VERROUILLÉ
est éteint, on peut ouvrir la
porte.
Pour faire redémarrer le lavage exactement de
lendroit il a été interrompu, appuyer une nouvelle
fois sur la touche.
Stand-by
Ce lavante-séchante, conformément aux nouvelles
normes en vigueur dans le domaine de l'économie
d'énergie, est équipée d'un système d'extinction
automatique (veille) activé après environ 30 minutes
d'inutilisation. Appuyez brièvement sur la touche ON/
OFF et attendre que la machine soit réactivée.
Description du lavante-séchante
et démarrage dun programme
Voyants
DÉROULEMENT
CYCLE/DÉPART DIFFÉRÉ
Voyant
HUBLOT
VERROUILLÉ
Touche avec
voyant
START/
PAUSE
Bandeau de commandes
Tiroir à produits lessiviels
Bouton
SÉCHAGE
Touches avec voyants
FONCTION
Touche
ON/OFF
Bouton
PROGRAMMES
Bouton
TEMPÉRATURE
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44

Indesit IWDC 7125 B (EX)60HZ Mode d'emploi

Catégorie
Machines à laver
Taper
Mode d'emploi

dans d''autres langues