MTD Trimmer TB20DC Manuel utilisateur

Marque: MTD

Modèle: Trimmer TB20DC

Catégorie: Coupe-herbe

Taper: Manuel utilisateur

Ce manuel convient également à

TB20DC

Operator’s Manual

2-Cycle Gasoline

Trimmer

Model TB20DC

IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY

P/N 769-02250 (12/05)

INTRODUCTION

Copy the serial number

here:

THANK YOU

Thank you for buying this quality product. This modern

outdoor power tool will provide many hours of useful

service. You will find it to be a great labor-saving device.

This operator’s manual provides you with easy-to-

understand operating instructions. Read the whole

manual and follow all the instructions to keep your new

outdoor power tool in top operating condition.

PRODUCT REFERENCES, ILLUSTRATIONS

AND SPECIFICATIONS

All information, illustrations, and specifications in this

manual are based on the latest product information

available at the time of printing. We reserve the right to

make changes at any time without notice.

Reserved.

SERVICE INFORMATION

Service on this unit both within and after the warranty

period should be performed only by an authorized and

approved service dealer.

For service call 1-800-520-5520 to obtain a list of

authorized service dealers near you. For more details

about your unit, visit our website at www.troybilt.com.

DO NOT RETURN THE UNIT TO THE RETAILER.

PROOF OF PURCHASE WILL BE REQUIRED FOR

WARRANTY SERVICE.

Before beginning, locate the unit’s model plate. It lists

the model and serial numbers of your unit. Refer to the

sample plate below and copy the information for future

reference.

S/N :

ITEM :

MODEL :

Make sure you carefully read and understand this manual

before starting or operating this equipment.

THIS PRODUCT IS COVERED BY ONE OR MORE U.S.

PATENTS. OTHER PATENTS PENDING.

TABLE OF CONTENTS

Service Information . . . . . . . . . . . . . . . . . . . . . . . . .2

Rules for Safe Operation . . . . . . . . . . . . . . . . . . . . .3

Know Your Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Assembly Instructions . . . . . . . . . . . . . . . . . . . . . . .7

Oil and Fuel Information . . . . . . . . . . . . . . . . . . . . . .8

Starting/Stopping Instructions . . . . . . . . . . . . . . . . .9

Operating Instructions . . . . . . . . . . . . . . . . . . . . . .10

Maintenance and Repair Instructions . . . . . . . . . . .12

Cleaning and Storage . . . . . . . . . . . . . . . . . . . . . . .16

Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . .17

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Warranty Information . . . . . . . . . . . . . . . . . . . . . . .20

Parts List . . . . . . . . . . . . . . . . . . . .Inside Back Cover

Copy the model and parent

part number here:

WARNING

THE ENGINE EXHAUST FROM THIS

PRODUCT CONTAINS CHEMICALS

KNOWN TO THE STATE OF CALIFORNIA

TO CAUSE CANCER, BIRTH DEFECTS

OR OTHER REPRODUCTIVE HARM.

SPARK ARRESTOR NOTE

NOTE: For users on U.S. Forest Land and in the

states of California, Maine, Oregon and Washington.

All U.S. Forest Land and the state of California (Public

Resources Codes 4442 and 4443), Oregon and

Washington require, by law that certain internal

combustion engines operated on forest brush and/or

grass-covered areas be equipped with a spark arrestor,

maintained in effective working order, or the engine be

constructed, equipped and maintained for the prevention

of fire. Check with your state or local authorities for

regulations pertaining to these requirements. Failure to

follow these requirements could subject you to liability or

a fine. This unit is factory equipped with a spark

arrestor. If it requires replacement, ask your LOCAL

SERVICE DEALER to install the Accessory Muffler

Assembly, Part #753-05169 (replaces Part #753-04618).

CALIFORNIA PROPOSITION 65 WARNING

RULES FOR SAFE OPERATION

READ ALL INSTRUCTIONS

BEFORE OPERATING

• Read the instructions carefully. Be familiar with the

controls and proper use of the unit.

• Do not operate this unit when tired, ill, or under the

influence of alcohol, drugs, or medication.

• Children and teens under the age of 15 must not use

the unit, except for teens guided by an adult.

• All guards and safety attachments must be installed

properly before operating the unit.

• Inspect the unit before use. Replace damaged parts.

Check for fuel leaks. Make sure all fasteners are in

place and secure. Replace parts that are cracked,

chipped, or damaged in any way. Do not operate the

unit with loose or damaged parts.

• Carefully inspect the area before starting the unit.

Remove all debris and hard or sharp objects such as

glass, wire, etc.

• Be aware of the risk of injury to the head, hands and

feet.

• Clear the area of children, bystanders, and pets. At a

minimum, keep all children, bystanders, and pets

outside a 50 feet (15 m.) radius; there still may be a

risk to bystanders from thrown objects. Bystanders

should be encouraged to wear eye protection. If you

are approached, stop the unit immediately.

• Use only 0.080 inch (

2.03 mm) diameter original

equipment manufacturer replacement line. Never use

metal-reinforced line, wire or rope. These can break

off and become dangerous projectiles.

• Squeeze the throttle control and check that it returns

automatically to the idle position. Make all adjustments

or repairs before using unit.

SAFETY WARNINGS FOR GAS UNITS

• Store fuel only in containers specifically designed and

approved for the storage of such materials.

• Avoid creating a source of ignition for spilled fuel. Do

not start the engine until fuel vapors dissipate.

SYMBOL MEANING

The purpose of safety symbols is to attract your

attention to possible dangers. The safety symbols,

and their explanations, deserve your careful attention

and understanding. The safety warnings do not by

themselves eliminate any danger. The instructions or

warnings they give are not substitutes for proper

accident prevention measures.

NOTE: Advises you of information or instructions vital to

the operation or maintenance of the equipment.

SYMBOL MEANING

When using the unit,

you must follow the

safety rules. Please read these instructions

before operating the unit in order to ensure

the safety of the operator and any bystanders.

Please keep these instructions for later use.

WARNING:

• IMPORTANT SAFETY INSTRUCTIONS •

Failure to obey a

safety warning can

result in injury to yourself and others.

Always follow the safety precautions to

reduce the risk of fire, electric shock and

personal injury.

WARNING:

Failure to obey a

safety warning will

result in serious injury to yourself or to

others. Always follow the safety precautions

to reduce the risk of fire, electric shock and

personal injury.

DANGER:

Failure to obey a

safety warning may

result in property damage or personal injury

to yourself or to others. Always follow the

safety precautions to reduce the risk of fire,

electric shock and personal injury.

CAUTION:

Indicates

danger,

warning or caution. Attention is required in

order to avoid serious personal injury. May

be used in conjunction with other symbols

or pictographs.

SAFETY ALERT:

Gasoline is highly

flammable, and its

vapors can explode if ignited. Take the

following precautions:

WARNING:

Read the Operator’s Manual(s) and follow all

warnings and safety instructions.

Failure to do so can result in serious injury to the

operator and/or bystanders.

FOR QUESTIONS, CALL 1-800-520-5520

• Keep hands, face, and feet at a distance from all

moving parts. Do not touch or try to stop the cutting

attachment when it is rotating.

• Do not touch the engine or muffler. These parts get

extremely hot from operation. They remain hot for a

short time after you turn off the unit.

• Do not operate the engine faster than the speed

needed to cut, trim or edge. Do not run the engine at

high speed when you are not cutting.

• Always stop the engine when cutting is delayed or

when walking from one cutting location to another.

• If you strike or become entangled with a foreign

object, stop the engine immediately and check for

damage. Do not operate before repairing damage. Do

not operate the unit with loose or damaged parts.

• Stop and switch the engine to off for maintenance,

repair, or for changing the cutting attachment or other

attachments.

Use only original equipment manufacturer

replacement parts and accessories for this unit. These

are available from your authorized service dealer. Use

of any unauthorized parts or accessories could lead to

serious injury to the user, or damage to the unit, and

void your warranty.

• Keep unit clean of vegetation and other materials.

They may become lodged between the cutting

attachment and shield.

• To reduce fire hazard, replace faulty muffler and spark

arrestor, keep the engine and muffler free from grass,

leaves, excessive grease or carbon build up.

OTHER SAFETY WARNINGS

• Never store the unit, with fuel in the tank, inside a

building where fumes may reach an open flame or

spark.

• Allow the engine to cool before storing or transporting.

Be sure to secure the unit while transporting.

• Store the unit in a dry area, locked up or up high

to prevent unauthorized use or damage, out of the

reach of children.

• Never douse or squirt the unit with water or any other

liquid. Keep handles dry, clean and free from debris.

Clean after each use. See the Cleaning and Storage

instructions.

• Keep these instructions. Refer to them often and use

them to instruct other users. If you loan someone this

unit, also loan them these instructions.

SAVE THESE

INSTRUCTIONS

• Always stop the engine and allow it to cool before filling

the fuel tank. Never remove the cap of the fuel tank, or

add fuel, when the engine is hot. Never operate the unit

without the fuel cap securely in place. Loosen the fuel

tank cap slowly to relieve any pressure in the tank.

• Mix and add fuel in a clean, well-ventilated outdoor area

where there are no sparks or flames. Slowly remove the

fuel cap only after stopping engine. Do not smoke while

fueling or mixing fuel. Wipe up any spilled fuel from the

unit immediately. Always wipe unit dry before using.

• Move the unit at least 30 feet (9.1 m) from the fueling

source and site before starting the engine. Do not

smoke or allow sparks and open flames near the area

while adding fuel or operating the unit.

WHILE OPERATING

• Never start or run the unit inside a closed room or

building. Breathing exhaust fumes can kill. Operate

this unit only in a well ventilated outdoor area.

• Wear safety glasses or goggles that are marked as

meeting ANSI Z87.1-1989 standards. Also wear

ear/hearing protection when operating this unit. Wear

a face or dust mask if the operation is dusty. Long

sleeve shirts are recommended.

• Wear heavy, long pants, boots and gloves. Do not

wear loose clothing, jewelry, short pants, sandals or

go barefoot. Secure hair above shoulder level.

• The cutting attachment shield must always be in place

while operating the unit. Do not operate unit without

both trimming lines extended, and the proper line

installed. Do not extend the trimming line beyond the

length of the shield.

• This unit has a clutch. The cutting attachment remains

stationary when the engine is idling. If it does not, have

the unit adjusted by an authorized service technician.

• Adjust the D-handle to your size to provide the best

grip.

• Be sure the cutting attachment is not in contact with

anything before starting the unit.

• Use the unit only in daylight or good artificial light.

• Avoid accidental starting. Be in the starting position

whenever pulling the starter rope. The operator and

unit must be in a stable position while starting. See

Starting/Stopping Instructions.

• Use the right tool. Only use this tool for the purpose

intended.

• Do not overreach. Always keep proper footing and

balance.

• Always hold the unit with both hands when operating.

Keep a firm grip on both the front and rear handle or

grips.

RULES FOR SAFE OPERATION

SYMBOL MEANING

• THROWN OBJECTS AND

ROTATING CUTTER CAN CAUSE

SEVERE INJURY

WARNING:Do not

operate without the cutting

attachment shield in place. Keep

away from the rotating cutting

attachment.

• ON/OFF STOP CONTROL

ON / START / RUN

• ON/OFF STOP CONTROL

OFF or STOP

• HOT SURFACE WARNING

Do not touch a hot muffler or

cylinder. You may get burned. These

parts get extremely hot from

operation. When turned off they

remain hot for a short time.

• OIL

Refer to operator's manual for the

proper type of oil.

SYMBOL MEANING

• SAFETY ALERT SYMBOL

Indicates danger, warning, or

caution. May be used in conjunction

with other symbols or pictographs.

• WARNING - READ OPERATOR'S

MANUAL

Read the Operator’s Manual(s) and

follow all warnings and safety

instructions. Failure to do so can

result in serious injury to the

operator and/or bystanders.

• WEAR EYE AND HEARING

PROTECTION

WARNING:Thrown

objects and loud noise can cause

severe eye injury and hearing loss.

Wear eye protection meeting ANSI

Z87.1-1989 standards and ear

protection when operating this unit.

Use a full face shield when needed.

• KEEP BYSTANDERS AWAY

WARNING:Keep all

bystanders, especially children and

pets, at least 50 feet (15 m.) from the

operating area.

• UNLEADED FUEL

Always use clean, fresh unleaded fuel.

SAFETY AND INTERNATIONAL SYMBOLS

This operator's manual describes safety and international symbols and pictographs that may appear on this product.

Read the operator's manual for complete safety, assembly, operating and maintenance and repair information.

RULES FOR SAFE OPERATION

APPLICATIONS

As a trimmer:

• Cutting grass and light weeds.

• Edging

• Decorative trimming around trees, fences, etc.

Other optional accessories may be used with the

TB20DC. Refer to Operating the EZ-Link System for

a list of add-ons.

KNOW YOUR UNIT

Cutting Attachment

Shield

Fuel Cap

Throttle

Control

D-Handle

Cutting Attachment

Shaft Grip

Primer Bulb

Blue Choke

Lever

Air Filter/Muffler

Cover

Engine

Stand

Spark Plug

Shaft Housing

Starter Rope Grip

Spark Plug

Muffler

Blue Choke Lever

Line Cutting Blade

On/Off Stop

Control

EZ-Link™

ASSEMBLY INSTRUCTIONS

INSTALLING AND ADJUSTING THE D-HANDLE

1. Remove the screws and bottom clamp piece that

were installed on the D-handle for shipping.

2. Place D-handle the over the shaft housing and onto

the bottom clamp (Fig. 1). Place it a minimum of 6

inches (15.24 cm) from the end of the shaft grip.

3. Start screws with a large Flat-head or T-25 Torx

screwdriver. Do not tighten until you make the handle

adjustment.

4. If the D-handle was pre-installed, loosen the screws

on the handle just enough to move it.

5. While holding the unit in the operating position

(Fig. 2), position the D-handle to the location that

provides you the best grip.

6. Tighten the clamp screws evenly, until the D-handle

is secure.

INSTALL THE CUTTING ATTACHMENT SHIELD

Use the following instructions if the cutting attachment

shield on your unit is not installed.

1. Place the cutting attachment shield onto the shaft

housing. Be sure the guard mounting bracket slides

into the slot on the edge of the cutting shield. Rotate

the shield into place, counterclockwise. The holes in

the guard mounting bracket and cutting attachment

shield will line up (Fig. 3).

2. From inside the cutting attachment shield, push the square

bolt through the hole until the threaded end protrudes

through the guard mounting bracket (Fig. 4).

Guard

Mounting

Bracket

Shaft Housing

Square Bolt

Cutting Attachment

Shield

3. Put the washer on the bolt, then screw the wing nut

onto the bolt and tighten. Figure 5 shows the

installation process from underneath the unit.

Guard

Mounting

Bracket

Wing Nut

Cutting Attachment and Shield: Underside View

Cutting

Attachment

Shield

Wing Nut

Washer

Square Bolt

Washer

Hole

Fig. 3

Fig. 4

Fig. 5

Never operate the

trimmer without the

cutting attachment shield in place to

prevent serious personal injury.

WARNING:

Fig. 2

(4) Screws

Shaft

Housing

D-Handle

Bottom Clamp

Shaft Grip

Minimum 6 inches

(15.24 cm)

On/Off Stop Control

Fig. 1

OIL AND FUEL INFORMATION

NOTE: Dispose of the old fuel/oil mix in accordance to

Federal, State and Local regulations.

OIL AND FUEL MIXING INSTRUCTIONS

Old and/or improperly mixed fuel are the main reasons

for the unit not running properly. Be sure to use fresh,

clean unleaded fuel. Follow the instructions carefully for

the proper fuel/oil mixture.

Definition of Blended Fuels

Today's fuels are often a blend of gasoline and

oxygenates such as ethanol, methanol, or MTBE (ether).

Alcohol-blended fuel absorbs water. As little as 1%

water in the fuel can make fuel and oil separate. It forms

acids when stored. When using alcohol-blended fuel,

use fresh fuel (less than 60 days old).

Using Blended Fuels

If you choose to use a blended fuel, or its use is

unavoidable, follow recommended precautions:

• Always use the fresh fuel mix explained in your

operator's manual

• Always agitate the fuel mix before fueling the unit

• Drain the tank and run the engine dry before storing

the unit

Using Fuel Additives

The bottle of 2-cycle oil that came with your unit

contains a fuel additive which will help inhibit corrosion

and minimize the formation of gum deposits. It is

recommended that you use our 2-cycle oil with this unit.

If unavailable, use a good 2-cycle oil designed for

air-cooled engines along with a fuel additive, such as

STA-BIL

Gas Stabilizer or an equivalent. Add 0.8 oz.

(23 ml.) of fuel additive per gallon of fuel according to the

instructions on the container. NEVER add fuel additives

directly to the unit's fuel tank.

Thoroughly mix the proper ratio of 2-cycle engine oil

with unleaded gasoline in a separate fuel can. Use a 40:1

fuel/oil ratio. Do not mix them directly in the engine fuel

tank. See the table below for specific gas and oil mixing

ratios.

NOTE: One gallon (3.8 liters) of unleaded gasoline mixed

with one 3.2 oz. (95 ml.) bottle of

2-cycle oil makes a 40:1 fuel/oil ratio.

UNLEADED GAS 2 CYCLE OIL

1 GALLON US

(3.8 LITERS)

3.2 FL. OZ.

(95 ml)

1 LITER 25 ml

MIXING RATIO - 40:1

Add fuel in a clean,

well ventilated

outdoor area. Wipe up any spilled fuel

immediately. Avoid creating a source of

ignition for spilt fuel. Do not start the engine

until fuel vapors dissipate.

WARNING:

Gasoline is

extremely

flammable. Ignited vapors may explode.

Always stop the engine and allow it to cool

before filling the fuel tank. Do not smoke

while filling the tank. Keep sparks and open

flames at a distance from the area.

WARNING:

Remove fuel cap

slowly to avoid injury

from fuel spray. Never operate the unit

without the fuel cap securely in place

WARNING:

For proper engine

operation and

maximum reliability, pay strict attention to

the oil and fuel mixing instructions on the

2-cycle oil container. Using improperly mixed

fuel can severely damage the engine.

CAUTION:

STARTING/STOPPING INSTRUCTIONS

STARTING INSTRUCTIONS

Fig. 6

Throttle Control

STOPPING INSTRUCTIONS

1. Release your finger from the throttle control. Allow

the engine to cool down by idling.

2. Put the On/Off Stop Control in the OFF (O) position

(Fig. 6).

Fig. 8

1. Mix gas with oil. Fill fuel tank with fuel/oil

mixture. See Oil and Fuel Mixing Instructions.

NOTE: There is no need to turn the unit on.

The On/Off Stop Control is in the ON ( I )

position at all times.

2. Fully press and release the primer bulb 10

times, slowly. Some amount of fuel should be

visible in the primer bulb and fuel lines (Fig. 7).

If you can’t see fuel in the bulb, press and

release the bulb as many times as it takes

before you can see fuel in it.

3. Place the blue choke lever in Position 1 (Fig. 7).

4. Crouch in the starting position (Fig. 8), squeeze

the throttle control, and pull the starter rope

briskly 5 times.

5. Place the blue choke lever in Position 2 (Fig. 7).

6. While squeezing the throttle control, pull the

starter rope briskly until the engine starts.

7. Keep the throttle squeezed and allow the

engine to warm up for 15 to 30 seconds.

NOTE: Engine may take longer to warm up

and reach maximum operating speed at colder

temperatures.

NOTE: Unit is properly warmed up when

engine accelerates without hesitation.

8. Once the engine is warmed up, place the blue

choke lever in Position 3 (Fig. 7). The unit is

ready for use.

IF...

the engine hesitates, return choke lever to

Position 2 (Fig. 7) and continue warm up.

IF...

the engine does not start, go back to step 2.

IF...

the engine fails to start after a few attempts,

place the blue choke lever in Position 3 and

squeeze the throttle control. Pull the starter

rope briskly 3 to 8 times. The engine should

start. If not, repeat.

IF WARM...

If the engine is already warm, make

sure the On/Off Stop control is in the ON

position and start the unit with the blue choke

lever in Position 2. After the unit starts, move

the blue choke lever to Position 3.

Start/On ( I )

Stop/Off (O)

Throttle

Control

Starting

Position

Operate this unit

only in a well-

ventilated outdoor area. Carbon monoxide

exhaust fumes can be lethal in a confined area.

WARNING:

Avoid accidental

starting. Make sure

you are in the starting position when pulling

the starter rope (Fig. 8). To avoid serious

injury, the operator and unit must be

in a stable position while starting.

WARNING:

Trimmer

Equipped With

Spring Assist

Starting ™

Fig. 7

Blue Choke

Lever

Primer

Bulb

OPERATING INSTRUCTIONS

For decorative trimming/edging with the line head cutting

attachment, lock the release button of the cutting

attachment into the 90° hole (Fig. 11).

OPERATING THE EZ-LINK™ SYSTEM

The EZ-Link™ system enables the use of these optional

Add-Ons.

Cultivator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBGC

Edger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBLE

Hedge Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . TBAH

Straight Shaft Trimmer . . . . . . . . . . . . . . . . . . . . . . TBSS

Turbo Blower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBTB

Pole Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBPS

Brushcutter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .TBBC

Removing the Cutting Attachment or Add-Ons

1. Turn the knob counterclockwise to loosen (Fig. 9).

2. Press and hold the release button (Fig. 9).

3. While firmly holding the upper shaft housing, pull

the cutting attachment or add-on straight out of the

EZ-Link™ coupler (Fig. 10).

Installing the Cutting Attachment or Add-Ons

NOTE: To make installing or removing the add-on

easier, place the unit on the ground or on a work

bench.

1. Turn knob counterclockwise to loosen (Fig. 9).

Fig. 9

EZ-Link™ Coupler

Release Button

Guide Recess

Knob

Primary Hole

Upper Shaft Housing

90˚ Edge

Trimming Hole

EZ-Link™ Coupler

2. While firmly holding the add-on, push it straight into

the EZ-Link™ coupler (Fig. 10).

NOTE: Aligning the release button with the guide recess

will help installation (Fig. 9).

3. Turn the knob clockwise to tighten (Fig. 11).

Fig. 10

Fig. 11

Knob

Lower Shaft Housing

Release Button

To avoid serious

personal injury and

damage to the unit, shut the unit off before

removing or installing add-ons.

WARNING:

The add-ons with the

coupler system is to

be used in the primary hole only. Using the

wrong hole could lead to personal injury or

damage to the unit.

CAUTION:

Lock the release

button in the primary

hole (Fig. 10) and securely tighten the knob

before operating this unit.

CAUTION:

Before you begin

using any

attachment, read and understand the manual

that came with the attachment. Follow all

safety information contained within.

WARNING:

NOTE: Do not rest the Bump Head™ on the ground

while the unit is running.

Some line breakage will occur from:

• Entanglement with foreign matter

• Normal line fatigue

• Attempting to cut thick, stalky weeds

• Forcing the line into objects such as walls or fence

posts

TIPS FOR BEST TRIMMING RESULTS

• Keep the cutting attachment parallel to the ground.

• Do not force the cutting attachment. Allow the tip of

the line to do the cutting, especially along walls.

Cutting with more than the tip will reduce cutting

efficiency and may overload the engine.

• Cut grass over 8 inches (200 mm) by working from

top to bottom in small increments to avoid

premature line wear or engine drag.

• Cut from right to left whenever possible. Cutting to

the left improves the unit's cutting efficiency.

Clippings are thrown away from the operator.

• Slowly move the trimmer into and out of the cutting

area at the desired height. Move either in a forward-

backward or side-to-side motion. Cutting shorter

lengths produces the best results.

• Trim only when grass and weeds are dry.

• The life of your cutting line is dependent upon:

• Following the trimming techniques

• What vegetation is being cut

• Where vegetation is cut

For example, the line will wear faster when trimming

against a foundation wall as opposed to trimming

around a tree.

HOLDING THE TRIMMER

Before operating the unit, stand in the operating position

(Fig. 12). Check for the following:

• The operator is wearing eye protection and proper

clothing

• With a slightly-bent right arm, the operator’s hand is

holding the shaft grip

• The operator’s left arm is straight, the left hand

holding the D-handle

• The unit is at waist level

•

The cutting attachment is parallel to the ground and

easily contacts the grass without the need to bend ove

ADJUSTING TRIMMING LINE LENGTH

The Bump Head™ cutting attachment allows you to

release trimming line without stopping the engine. To

release more line, lightly tap the cutting attachment on the

ground (Fig. 13) while operating the trimmer at high speed.

NOTE: Always keep the trimming line fully extended.

Line release becomes more difficult when the

cutting line gets shorter.

Each time the head is bumped, about 1 inch (25.4 mm)

of trimming line releases. A blade in the cutting

attachment shield will cut the line to the proper length if

any excess line is released.

For best results, tap the bump knob on bare ground or

hard soil. If you attempt a line release in tall grass, the

engine may stall. Always keep the trimming line fully

extended. Line release becomes more difficult when the

cutting line gets shorter.

OPERATING INSTRUCTIONS

Fig. 13

Fig. 12

DECORATIVE TRIMMING

Decorative trimming is accomplished by removing all

vegetation around trees, posts, fences and more.

Rotate the whole unit so that the cutting attachment is at

a 30° angle to the ground (Fig. 14).

Fig. 14

Do not remove or alter

the line cutting blade

assembly. Excessive line length will make the

clutch overheat. This may lead to serious

personal injury or damage to the unit.

CAUTION:

Always wear eye,

hearing, foot and

body protection to reduce the risk of injury

when operating this unit.

WARNING:

MAINTENANCE AND REPAIR INSTRUCTIONS

MAINTENANCE SCHEDULE

Perform these required maintenance procedures at the

frequency stated in the table. These procedures should

also be a part of any seasonal tune-up.

NOTE: Some maintenance procedures may require

special tools or skills. If you are unsure about

these procedures take your unit to any non-road

engine repair establishment, individual or

authorized service dealer.

NOTE: Maintenance, replacement, or repair of the

emission control devices and system may be

performed by any non-road engine repair

establishment, individual or authorized service

dealer.

In order to assure peak performance of your engine,

inspection of the engine exhaust port may be necessary

after 50 hours of operation. If you notice lost RPM, poor

performance or general lack of acceleration, this service

may be required. If you feel your engine is in need of this

inspection, refer service to any non-road engine repair

establishment, individual or authorized service dealer for

repair. DO NOT attempt to perform this process yourself

as engine damage may result from contaminants

involved in the cleaning process for the port.

FREQUENCY MAINTENANCE REQUIRED REFER TO

Before starting engine Fill fuel tank with fresh fuel Page 8

Every 10 hours Clean and re-oil air filter Page 14

Every 25 hours

Check and clean spark arrestor

Check spark plug condition and gap

Page 15

Page 16

Every 50 hours

Inspect exhaust port and spark arrestor screen for clogging or

obstruction to assure maximum performance levels

Page 15

LINE INSTALLATION

This section covers both SplitLine™ and standard single

line installation.

Always use original equipment manufacturer 0.080 in.

(2.03 mm) replacement line. Line other than the specified

may make the engine overheat or fail.

There are two methods to replace the trimming line:

• Wind the inner reel with new line

• Install a prewound inner reel

Winding the Existing Inner Reel

1. Hold the outer spool with one hand and unscrew the

Bump Knob™ counterclockwise (Fig. 15). Inspect the

bolt inside the Bump Knob to make sure it moves

freely. Replace the Bump Knob if damaged.

2. Remove the inner reel from the outer spool (Fig. 16).

3. Remove spring from the inner reel (Fig. 16).

4. Use a clean cloth to clean the the inner reel, spring,

shaft, and inner surface of the outer spool.

5. Check the indexing teeth on the inner reel and outer

spool for wear (Fig. 17). If necessary, remove burrs or

replace the reel and spool.

Bump Knob™

Bolt

Fig. 15

Inner Reel

Spring

Outer Spool

Indexing Teeth

Fig. 17

Fig. 16

Never use metal-

reinforced line, wire,

chain or rope. These can break off and

become dangerous projectiles.

WARNING:

To prevent serious

injury, never perform

maintenance or repairs with unit running.

Always service and repair a cool unit.

Disconnect the spark plug wire to ensure that

the unit cannot start.

WARNING:

MAINTENANCE AND REPAIR INSTRUCTIONS

Fig. 22

Fig. 18

NOTE: SplitLine™ can only be used with the inner reel

with the slotted holes. Single line can be used on

either type of inner reel. Use Figure 18 to identify

the inner reel you have.

NOTE: Always use the correct line length when installing

trimming line on the unit. The line may not release

properly if the line is too long.

Single Line Installation

Go To Step 8 for SplitLine™ Installation

6. Take approximately 20 feet (6 m) of new trimming

line, loop it into two equal lengths. Insert each end of

the line through one of the two holes in the inner reel

(Fig. 19). Pull the line through the inner reel so that

the loop is as small as possible.

7. Wind the lines in tight even layers, onto the reel

(Fig. 20). Wind the line in the direction indicated on

the inner reel. Place your index finger between the

two lines to stop the lines from overlapping. Do not

overlap the ends of the line. Proceed to step 11.

SplitLine™ Installation

8. Take approximately 10 feet (3 m) of new trimming

line. Insert one end of the line through one of the two

holes in the inner reel (Fig. 21). Pull the line through

the inner reel until only about 4 inches is left out.

9. Insert the end of the line into the open hole in the

inner reel and pull the line tight to make the loop as

small as possible (Fig. 21).

10. Before winding, split the line back about 6 inches.

11. Wind the line in tight even layers in the direction

indicated on the inner reel.

NOTE: Failure to wind the line in the direction indicated will

cause the cutting attachment to operate incorrectly.

Slotted

Holes

For Use with SplitLine™

or Single Line

For Use with Single

Line ONLY

Holding Slots

NOTE: The spring must be assembled on the inner reel

before reassembling the cutting attachment.

14. Hold the inner reel in place and install the bump knob

by turning clockwise. Tighten securely.

12. Insert the ends of the line into the two holding slots

(Fig. 22).

13. Insert the ends of the line through the eyelets in the

outer spool and place inner reel with spring inside the

outer spool (Fig. 23). Push the inner reel and outer

spool together. While holding the inner reel and outer

spool, grasp the ends and pull firmly to release the

line from the holding slots in the reel.

Loop

Fig. 19

Fig. 20

Loop

Fig. 21

Spring

Fig. 23

MAINTENANCE AND REPAIR INSTRUCTIONS

INSTALLING A PREWOUND REEL

1. Hold the outer spool with one hand and unscrew the

bump knob counterclockwise (Fig. 15). Inspect the bolt

inside the bump knob to make sure it moves freely.

Replace the bump knob if damaged.

2. Remove the old inner reel from the outer spool

(Fig. 16).

3. Remove the spring from the old inner reel

(Fig. 16).

4. Place the spring in the new inner reel.

NOTE: The spring must be assembled on the inner reel

before reassembling the cutting attachment.

5. Insert the ends of the line through the eyelets in the

outer spool (Fig. 23).

6. Place the new inner reel inside the outer spool. Push the

inner reel and outer spool together. While holding the

inner reel and outer spool, grasp the ends and pull firmly

to release the line from the holding slots in the spool.

7. Hold the inner reel in place and install the bump knob

by turning clockwise. Tighten securely.

Cleaning the Air Filter

Clean and re-oil the air filter every 10 hours of operation.

It is an important item to maintain. Failure to maintain

your air filter properly can result in poor performance or

can cause permanent damage to your engine.

1. Remove air filter/muffler cover. Refer to Removing

the Air Filter/Muffler Cover.

2. Turn cover over and look inside to locate the air filter.

Remove the air filter from inside the air filter/muffler

cover (Fig. 25).

3. Wash the filter in detergent and water (Fig. 26). Rinse

the filter thoroughly. Squeeze out excess water. Allow

it to dry completely.

4. Apply enough clean SAE 30 oil to lightly coat the filter

(Fig. 27).

5. Squeeze the filter to spread and remove excess oil

(Fig. 28).

AIR FILTER MAINTENANCE

Removing the Air Filter/Muffler Cover

1. Remove the four (4) screws securing the air

filter/muffler cover (Fig. 24). Use a flat blade or

T20 Torx bit screwdriver.

2. Pull the cover from the engine. Do not force.

Screws

Fig. 24

6. Replace the air filter inside the air filter/muffler cover

(Fig. 25).

NOTE: Operating the unit without the air filter and air

filter/muffler cover assembly will VOID the

warranty.

Reinstalling the Air Filter/Muffler Cover

1. Place the air filter/muffler cover over the back of the

carburetor and muffler. Align the screw holes.

2. Insert the four (4) screws into the holes in the air

filter/muffler cover (Fig. 24) and tighten.

Do not over tighten.

Blue Choke

Lever

Air Filter

Inside Muffler

Cover

To avoid serious

personal injury,

always turn your unit off and allow it to cool

before you clean or service it.

WARNING:

Fig. 25

Fig. 26

Fig. 27

Fig. 28

MAINTENANCE AND REPAIR INSTRUCTIONS

Check Fuel Mixture

Old and/or improperly mixed fuel is usually the reason

for improper unit performance. Drain and refill the tank

with fresh, properly-mixed fuel prior to making any

adjustments. Refer to Oil and Fuel Information.

Clean Air Filter

The condition of the air filter is important to the operation

of the unit. A dirty air filter will restrict air flow and

change the air/fuel mixture. This is often mistaken for an

out of adjustment carburetor. Check the condition of the

air filter before adjusting the idle speed screw. Refer to

Air Filter Maintenance.

Adjust Idle Speed Screw

If, after checking the fuel mixture and cleaning the air

filter, the engine still will not idle, adjust the idle speed

screw as follows:

1. Start the engine and let it run at a high idle for a

minute to warm up. Refer to Starting/Stopping

Instructions.

CARBURETOR ADJUSTMENT

The idle speed of the engine is adjustable through the air

filter/muffler cover (Fig. 30).

NOTE: Careless adjustments can seriously damage your

unit. An authorized service dealer should make

carburetor adjustments.

The cutting

attachment may spin

during idle speed adjustments. Wear

protective clothing and observe all safety

instructions to prevent serious personal injury.

WARNING:

Idle Speed Screw

Fig. 30

If the spark arrestor

hood and spark

arrestor screen are not tightened securely,

they could fall off causing damage to the unit

and possible serious personal injury.

WARNING:

Fig. 29

SPARK ARRESTOR MAINTENANCE

1. Remove air filter/muffler cover. Refer to Removing

the Air Filter/Muffler Cover.

2. Locate the muffler, but do not remove it. Find the

screw on the bottom of the muffler (Fig. 29). Remove

the screw using either a torx #20 or flat blade

screwdriver.

3. Carefully pry up the left side spark arrestor hood.

Two tabs act as hinges on the right side of the hood.

Flip open the spark arrestor hood like a door and

then pull its tabs out of the muffler slots.

4. Using a small flat blade screwdriver, carefully pry the

spark arrestor screen out from the inside of the spark

arrestor hood.

5. Clean the spark arrestor screen with a wire brush.

Replace it if it is damaged, or if you are unable to

clean it thoroughly.

6. Reinstall the spark arrestor screen snugly back into

the spark arrestor hood.

7. Reinstall the two hood tabs into the two muffler slots

and flip the spark arrestor hood closed.

8. Replace the screw you removed in Step 2 and tighten

it securely.

9. Reinstall the air filter/muffler cover.

Spark Arrestor

Screen

Spark Arrestor

Hood

Screw

Muffler

Engine

Tabs

Slots

MAINTENANCE AND REPAIR INSTRUCTIONS

CLEANING

Use a small brush to clean off the outside of the unit.

Do not use strong detergents. Household cleaners that

contain aromatic oils such as pine and lemon, and

solvents such as kerosene, can damage plastic housing

or handle. Wipe off any moisture with a soft cloth.

STORAGE

• Never store a fueled unit where fumes may reach an

open flame or spark.

• Allow the engine to cool before storing.

• Store the unit locked up to prevent unauthorized use

or damage.

• Store the unit in a dry, well-ventilated area.

• Store the unit out of the reach of children.

LONG TERM STORAGE

If you plan on storing the unit for an extended time, use

the following storage procedure:

1. Drain all fuel from the fuel tank into a container with

the same 2-cycle fuel mixture. Do not use fuel that

has been stored for more than 60 days. Dispose of

the old fuel/oil mix in accordance to Federal, State

and Local regulations.

2. Start the engine and allow it to run until it stalls. This

ensures that all fuel has been drained from the carburetor.

3. Allow the engine to cool. Remove the spark plug and

put 1 oz. (30 ml) of any high quality motor oil or

2-cycle oil into the cylinder. Pull the starter rope

slowly to distribute the oil. Reinstall the spark plug.

NOTE: Remove the spark plug and drain all of the oil

from the cylinder before attempting to start the

trimmer after storage.

4. Thoroughly clean the unit and inspect it for any loose

or damaged parts. Repair or replace damaged parts

and tighten loose screws, nuts or bolts. The unit is

ready for storage.

TRANSPORTING

• Allow the engine to cool before transporting.

• Drain fuel from unit.

• Tighten fuel cap before transporting.

• Secure the unit while transporting.

2. Release the throttle trigger and let the engine idle. If the

engine stops, insert a small phillips or flat blade

screwdriver into the hole in the air filter/muffler cover (Fig.

30). Turn the idle speed screw in, clockwise, 1/8 of a

turn at a time (as needed) until the engine idles smoothly.

NOTE: The cutting attachment should not rotate when

the engine idles.

3. If the cutting attachment rotates when the engine

idles, turn the idle speed screw counterclockwise

1/8 of a turn at a time (as needed), to reduce idle

speed.

Checking the fuel mixture, cleaning the air filter, and

adjusting the idle speed should solve most engine

problems. If not and all of the following are true:

• the engine will not idle

• the engine hesitates or stalls on acceleration

• there is a loss of engine power

Have the carburetor adjusted by an authorized service dealer.

REPLACING THE SPARK PLUG

Use a Champion RDJ7Y spark plug, or equivalent. The

correct air gap is 0.020 inch (0.5 mm). Remove the plug

after every 25 hours of operation and check its condition.

1. Stop the engine and allow it to cool. Grasp the plug

wire firmly and pull it from the spark plug.

2. Clean around the spark plug. Remove the spark plug

from the cylinder head by turning a 5/8-inch socket

counterclockwise.

3. Replace a cracked, fouled or dirty spark plug. Set the air

gap at 0.020 in. (0.5 mm) using a feeler gauge (Fig. 31).

4. Install a correctly-gapped spark plug in the cylinder

head. Tighten by turning the 5/8-inch socket

clockwise until snug.

If using a torque wrench torque to 110-120 in.•lb. (12.3-

13.5 N•m). Do not over tighten.

0.020 in.

(0.5 mm)

Fig. 31

To prevent serious

personal injury,

make sure the cutting attachment has

stopped rotating before you turn it off and

set it down.

WARNING:

Do not sand blast,

scrape or clean

electrodes. Grit in the engine could damage

the cylinder.

WARNING:

To avoid serious

personal injury,

always turn your trimmer off and allow it to cool

before you clean or maintain it.

WARNING:

TROUBLESHOOTING

If further assistance is required, contact your authorized service dealer.

CAUSE ACTION

Cutting attachment bound with grass Stop the engine and clean cutting attachment

Cutting attachment out of line Refill with new line

Inner reel bound up Replace the inner reel

Cutting head dirty Clean inner reel and outer spool

Line welded Disassemble, remove the welded section and rewind

Line twisted when refilled Disassemble and rewind the line

Not enough line is exposed Push the bump knob and pull out line until 4 inches

(102 mm) of line is outside of the cutting attachment

CAUSE ACTION

Old or improperly mixed fuel Drain gas tank and add fresh fuel mixture

Improper carburetor adjustment Take to an authorized service dealer for an adjustment

Fouled spark plug Replace or clean the spark plug

Plugged spark arrestor Clean or replace spark arrestor

CAUSE ACTION

Empty fuel tank Fill fuel tank with properly mixed fuel

Primer bulb wasn't pressed enough Press primer bulb fully and slowly 10 times

Engine is flooded Squeeze the trigger and pull the starter rope

Old or improperly mixed fuel Drain gas tank and add fresh fuel mixture

Fouled spark plug Replace or clean the spark plug

Plugged spark arrestor Clean or replace spark arrestor

The outside temperature is below 40º F Pull the starter rope up to 10-15 times

The outside temperature is above 90º F Squeeze the throttle control and pull the starter rope

ENGINE WILL NOT START

ENGINE WILL NOT IDLE

ENGINE WILL NOT ACCELERATE

ENGINE LACKS POWER OR STALLS WHEN CUTTING

CAUSE ACTION

Air filter is plugged Replace or clean the air filter

Old or improperly mixed fuel Drain gas tank and add fresh fuel mixture

Improper carburetor adjustment Adjust according to the Carburetor Adjustments section

CAUSE ACTION

Old or improperly mixed fuel Drain gas tank and add fresh fuel mixture

Improper carburetor adjustment Take to an authorized service dealer for an adjustment

Cutting attachment bound with grass Stop the engine and clean the cutting attachment

Dirty air filter Clean or replace the air filter

Plugged spark arrestor Clean or replace spark arrestor

CUTTING ATTACHMENT WILL NOT ADVANCE LINE

CAUSE ACTION

Oil, cleaner or lubricant in cutting head Clean and thoroughly dry the cutting head

CUTTING LINE ADVANCES UNCONTROLLABLY

SPECIFICATIONS

ENGINE*

DRIVE SHAFT & CUTTING ATTACHMENT*

*All specifications are based on the latest product information available at the time of printing. We reserve the right to

make changes at any time without notice.

Engine Type.......................................................................................................................................... Air-Cooled, 2-Cycle

Stroke.................................................................................................................................................... 1.25 in. (31.75 mm)

Displacement............................................................................................................................................. 1.9 cu in. (31 cc)

Clutch Type ......................................................................................................................................................... Centrifugal

Idle Speed RPM ...................................................................................................................................... 2,800 - 3,600 rpm

Operating RPM.................................................................................................................................................. 8,000+ rpm

Ignition Type.......................................................................................................................................................... Electronic

Ignition Switch .............................................................................................................................................. Rocker Switch

Spark Plug Gap ....................................................................................................................................... 0.020 in. (0.5 mm)

Lubrication................................................................................................................................................... Fuel/Oil Mixture

Fuel/Oil Ratio.................................................................................................................................................................. 40:1

Carburetor....................................................................................................................................... Diaphragm, All-Position

Starter ........................................................................................................................ Spring Assist Starting™ Auto Rewind

Muffler ..................................................................................................................................................... Baffled with Guard

Throttle............................................................................................................................................... Manual Spring Return

Fuel Tank Capacity....................................................................................................................................... 13 oz. (384 ml)

Drive Shaft Housing ......................................................................................................................... Steel Tube (EZ-Link™)

Throttle Control ........................................................................................................................................ Finger-Tip Trigger

Approximate Unit Weight (No fuel, with cutting attachment, shield, and D-handle)...................................... 13 lbs. (6 kg)

Cutting Mechanism ....................................................................................................................................... Bump Head™

Line Spool Diameter .............................................................................................................................. 3 inches (76.2 mm)

Trimming Line Diameter ................................................................................................................. 0.080 inches (2.03 mm)

Cutting Path Diameter ........................................................................................................................ 17 inches (43.18 cm)

California / EPA Emission Control Warranty Statement

Your Warranty Rights and Obligations

The California Air Resources Board, the Environmental Protection Agency and Troy-Bilt LLC (Troy-Bilt) are pleased to explain the

emission control system warranty on your 2005 and later small off-road engine. New small off-road engines must be designed, built

and equipped to meet stringent anti-smog standards. Troy-Bilt must warrant the emission control system on your small off-road

engine for the periods of time listed below provided there has been no abuse, neglect or improper maintenance of your small off-road

engine.

Your emission control system may include parts such as the carburetor or fuel-injected system, the ignition system, and catalytic

converter. Also included may be hoses, belts, connectors and other emission-related assemblies.

Where a warrantable condition exists, Troy-Bilt will repair your small off-road engine at no cost to you including diagnosis, parts and

labor.

The 2005 and later small off-road engines are warranted for two years. If any emission-related part on your engine is defective, the

part will be repaired or replaced by Troy-Bilt.

Owners Warranty Responsibilities

• As the small off-road engine owner, you are responsible for the performance of the required maintenance listed in your operator’s

manual. Troy-Bilt recommends that you retain all receipts covering maintenance on your small off-road engine, but Troy-Bilt cannot

deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance.

• As the small off-road engine owner, you however should be aware that Troy-Bilt may deny you warranty coverage if your small off-

road engine or a part has failed due to abuse, neglect, improper maintenance or unapproved modifications.

• You are responsible for presenting your small off-road engine to a Troy-Bilt Authorized Service Center as soon as a problem exists.

The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you should call 1-800-520-5520.

Manufacturer’s Warranty Coverage

• The warranty period begins on the date the engine or equipment is delivered to the retail purchaser.

• The manufacturer warrants to the initial owner and each subsequent purchaser, that the engine is free from defects in material and

workmanship which cause the failure of a warranted part for a period of two years.

• Repair or replacement of warranted part will be performed at no charge to the owner at an Authorized Troy-Bilt Service Center. For

the nearest location please contact Troy-Bilt at: 1-800-520-5520.

• Any warranted part which is not scheduled for replacement, as required maintenance or which is scheduled for only for regular

inspection to the effect of “Repair or Replace as Necessary” is warranted for the warranty period. Any warranted part which is

scheduled for replacement as required maintenance will be warranted for the period of time up to the first scheduled replacement

point for that part.

• The owner will not be charged for diagnostic labor which leads to the determination that a warranted part is defective, if the

diagnostic work is performed at an Authorized Troy-Bilt Service Center.

• The manufacturer is liable for damages to other engine components caused by the failure of a warranted part still under warranty.

• Failures caused by abuse, neglect or improper maintenance are not covered under warranty.

• The use of add-on or modified parts can be grounds for disallowing a warranty claim. The manufacturer is not liable to cover failures

of warranted parts caused by the use of add-on or modified parts.

• In order to file a claim, go to your nearest Authorized Troy-Bilt Service Center. Warranty services or repairs will be provided at all

Authorized Troy-Bilt Service Centers.

• Any manufacturer approved replacement part may be used in the performance of any warranty maintenance or repair of emission

related parts and will be provided without charge to the owner. Any replacement part that is equivalent in performance or durability

may be used in non-warranty maintenance or repair and will not reduce the warranty obligations of the manufacturer

• The following components are included in the emission related warranty of the engine, air filter, carburetor, primer, fuel lines, fuel

pick up/ fuel filter, ignition module, spark plug and muffler.

MANUFACTURER’S LIMITED WARRANTY FOR:

No implied warranty, including any implied warranty of

merchantability or fitness for a particular purpose, applies

after the applicable period of express written warranty above

as to the parts as identified. No other express warranty or

guaranty, whether written or oral, except as mentioned

above, given by any person or entity, including a dealer or

retailer, with respect to any product shall bind Troy-Bilt

During the period of the Warranty, the exclusive remedy is

repair or replacement of the product as set forth above.

(Some states do not allow limitations on how long an implied

warranty lasts, so the above limitation may not apply to you.)

The provisions as set forth in this Warranty provide the sole

and exclusive remedy arising from the sales. Troy-Bilt shall

not be liable for incidental or consequential loss or damages

including, without limitation, expenses incurred for substitute

or replacement lawn care services, for transportation or for

related expenses, or for rental expenses to temporarily

replace a warranted product. (Some states do not allow

limitations on how long an implied warranty lasts, so the above

limitation may not apply to you.)

In no event shall recovery of any kind be greater than the amount

of the purchase price of the product sold. Alteration of the safety

features of the product shall void this Warranty. You assume the

risk and liability for loss, damage, or injury to you and your

property and/or to others and their property arising out of the use

or misuse or inability to use the product.

This limited warranty shall not extend to anyone other than the

original purchaser, original lessee or the person for whom it was

purchased as a gift.

How State Law Relates to this Warranty: This warranty gives

you specific legal rights, and you may also have other rights

which vary from state to state.

To locate your nearest service dealer dial

1-800-520-5520.

Troy-Bilt LLC

P.O. Box 361131

Cleveland, OH 44136-0019

The limited warranty set forth below is given by Troy-Bilt LLC

(Troy-Bilt) with respect to new merchandise purchased and used

in the United States, its possessions and territories.

Troy-Bilt warrants this product against defects in material and

workmanship for a period of two (2) years commencing on the

date of original purchase and will, at its option, repair or replace,

free of charge, any part found to be defective in material or

workmanship. This limited warranty shall only apply if this product

has been operated and maintained in accordance with the

Operator’s Manual furnished with the product, and has not been

subject to misuse, abuse, commercial use, neglect, accident,

improper maintenance, alteration, vandalism, theft, fire, water or

damage because of other peril or natural disaster. Damage

resulting from the installation or use of any accessory or

attachment not approved by Troy-Bilt for use with the product(s)

covered by this manual will void your warranty as to any resulting

damage. This warranty is limited to ninety (90) days from the date

of original retail purchase for any Troy-Bilt product that is used for

rental or commercial purposes, or any other income-producing

purpose.

HOW TO OBTAIN SERVICE: Warranty service is available, WITH

PROOF OF PURCHASE THROUGH YOUR LOCAL

AUTHORIZED SERVICE DEALER. To locate

the dealer in your

area, visit our website at www.troybilt.com,

check for a listing in the

Yellow Pages, call 1-800-520-5520 or write to

P.O. Box 361131,

Cleveland, OH 44136-0019

This limited warranty does not provide coverage in the

following cases:

A. Tune-ups - Spark Plugs, Carburetor Adjustments, Filters

B. Wear items - Bump Knobs, Outer Spools, Cutting Line,

Inner Reels, Starter Pulley, Starter Ropes, Drive Belts

C. Troy-Bilt does not extend any warranty for products sold

or exported outside of the United States of America, its

possessions and territories, except those sold through

Troy-Bilt’s authorized channels of export distribution.

Troy-Bilt reserves the right to change or improve the design of

any Troy-Bilt Product without assuming any obligation to modify

any product previously manufactured.

La page charge ...

MTD Trimmer TB20DC Manuel utilisateur

Marque: MTD

Modèle: Trimmer TB20DC

Catégorie: Coupe-herbe

Taper: Manuel utilisateur

Ce manuel convient également à

TB20DC

Télécharger le PDF

rapport

dans d''autres langues

English: MTD Trimmer TB20DC User manual
español: MTD Trimmer TB20DC Manual de usuario

Autres documents

Troy-Bilt TB10CS Manuel utilisateur