Whirlpool WEGA25H0HZ Guide d'installation
- Catégorie
- Cuisinières
- Taper
- Guide d'installation
INSTALLATION INSTRUCTIONS
30" (76.2 CM) SLIDE-IN GAS RANGES
INSTRUCTIONS POUR L’INSTALLATION DES CUISINIÈRES
À GAZ ENCASTRABLES DE 30" (76,2 CM)
INSTRUCCIONES DE INSTALACIÓN ESTUFAS ELÉCTRICAS
DESLIZABLES DE 30" (76,2 cm)
W11085333A
Table of Contents
RANGE SAFETY .............................................................................2
INSTALLATION REQUIREMENTS ................................................. 4
Tools and Parts .............................................................................4
Location Requirements ................................................................4
Electrical Requirements ...............................................................7
Gas Supply Requirements ...........................................................7
INSTALLATION INSTRUCTIONS ................................................... 9
Unpack Range..............................................................................9
Install Anti-Tip Bracket .................................................................9
Adjust Leveling Legs ..................................................................10
Level Range ................................................................................11
Make Gas Connection ...............................................................11
Install Griddle .............................................................................13
Verify Anti-Tip Bracket Is Installed and Engaged ......................13
Electronic Ignition System .........................................................14
Remove/Replace Drawer ...........................................................14
Oven Door ..................................................................................15
Complete Installation .................................................................15
GAS CONVERSIONS ....................................................................16
Propane Gas Conversion ...........................................................16
Natural Gas Conversion .............................................................19
Adjust Flame Height ...................................................................22
Table des matières
SÉCURITÉ DE LA CUISINIÈRE ...................................................24
EXIGENCES D’INSTALLATION ...................................................26
Outillage et pièces ......................................................................26
Exigences d'emplacement .........................................................26
Spécifications électriques ..........................................................29
Spécifications de l’alimentation en gaz .....................................29
INSTRUCTIONS D’INSTALLATION .............................................31
Déballage de la cuisinière ..........................................................31
Installation de la bride antibasculement ....................................31
Réglage des pieds de nivellement .............................................32
Réglage de l’aplomb de la cuisinière .........................................33
Raccordement au gaz ................................................................33
Installation de la plaque à frire ...................................................34
Vérifier que la bride antibasculement est
bien installée et engagée ...........................................................35
Système d’allumage électronique..............................................36
Dépose et réinstallation du tiroir ................................................37
Porte du four ..............................................................................37
Achever l’installation ..................................................................38
CONVERSIONS POUR CHANGEMENT DE GAZ ......................39
Conversion pour l’alimentation au propane ..............................39
Conversion pour l’alimentation au gaz naturel ..........................43
Réglage de la taille des flammes ...............................................46
SEGURIDAD DE LA ESTUFA.......................................................48
REQUISITOS DE INSTALACIÓN .................................................50
Herramientas y piezas ................................................................50
Requisitos de ubicación .............................................................50
Requisitos eléctricos ..................................................................53
Requisitos del suministro de gas ...............................................53
INSTRUCCIONES DE INSTALACIÓN .........................................55
Desempaque la estufa ...............................................................55
Instalación del soporte anti-vuelco ............................................55
Regule las patas niveladoras .....................................................56
Nivelación de la estufa ...............................................................57
Conexión del suministro de gas ................................................57
Índice
Instalación de la plancha ...........................................................59
Verifique que el soporte antivuelco
esté instalado y enganchado .....................................................59
Sistema de encendido electrónico ............................................60
Quite/vuelva a colocar el cajón ..................................................60
Puerta del horno ......................................................................... 61
Completar la instalación ............................................................61
CONVERSIONES DE GAS ...........................................................62
Conversión a gas propano .........................................................62
Conversión a gas natural ...........................................................65
Cómo ajustar la altura de la llama .............................................68
IMPORTANT:
Installer: Leave installation instructions with the homeowner.
Homeowner: Keep installation instructions for future reference.
IMPORTANT :
Installateur : Remettre les instructions d'installation au propriétaire.
Propriétaire : Conserver les instructions d'installation pour référence ultérieure.
IMPORTANTE:
Instalador: Deje las instrucciones de instalación con el propietario.
Propietario: Conserve las instrucciones de instalación para referencia futura.
2
RANGE SAFETY
You can be killed or seriously injured if you don't immediately
You
can be killed or seriously injured if you don't
follow
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
follow instructions.
instructions.
DANGER
WARNING
WARNING: If the information in these instructions is not followed exactly, a fire or
explosion may result causing property damage, personal injury or death.
– Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
– WHAT TO DO IF YOU SMELL GAS:
•
Do not try to light any appliance.
•
Do not touch any electrical switch.
•
Do not use any phone in your building.
•
Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
instructions.
•
If you cannot reach your gas supplier, call the fire department.
– Installation and service must be performed by a qualified installer, service agency or
the gas supplier.
IMPORTANT: Do not install a ventilation system that blows air downward toward this gas cooking appliance. This type of
ventilation system may cause ignition and combustion problems with this gas cooking appliance resulting in personal injury or
unintended operation.
WARNING: Gas leaks cannot always be detected by smell.
Gas suppliers recommend that you use a gas detector approved by UL or CSA.
For more information, contact your gas supplier.
If a gas leak is detected, follow the “What to do if you smell gas” instructions.
3
In the State of Massachusetts, the following installation instructions apply:
■ Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gas fitter qualified or licensed by
the State of Massachusetts.
■ Acceptable Shut-off Devices: Gas Cocks and Ball Valves installed for use shall be listed.
■ A flexible gas connector, when used, must not exceed 4 feet (121.9 cm).
Tip Over Hazard
A child or adult can tip the range and be killed.
Install anti-tip bracket to floor or wall per installation instructions.
Slide range back so rear range foot is engaged in the slot of the anti-tip bracket.
Re-engage anti-tip bracket if range is moved.
Do not operate range without anti-tip bracket installed and engaged.
Failure to follow these instructions can result in death or serious burns to children and adults.
Anti-Tip
Bracket
To verify the anti-tip bracket is installed and engaged:
• Slide range forward.
• Look for the anti-tip bracket securely attached to floor or wall.
• Slide range back so rear range foot is under anti-tip bracket.
• See installation instructions for details.
Range Foot
WARNING
4
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools Needed
■ Tape measure
■ Phillips screwdriver
■ Flat-blade screwdriver
■ 1/8" (3 mm) flat-blade
screwdriver
■ Level
■ Drill
■ Wrench or pliers
■ Pipe wrench
■ 15/16" (24 mm) combination
wrench
■ 1/8" (3.2 mm) drill bit
(for wood floors)
■ Marker or pencil
Parts Supplied
Check that all parts are included.
■ Propane/Natural Gas Conversion Kit
■ #10 x 1
5
/
8
" (41.3 mm) screws
(for mounting anti-tip bracket) (2)
■ Anti-tip bracket (inside oven cavity)
Anti-tip bracket must be securely mounted to the back wall or
floor. Thickness of flooring may require longer screws to anchor
bracket to subfloor. Longer screws are available from your local
hardware store.
■ For Models:
WEG750H0H
WEGA25H0H
Burner Caps
5
Burner Grates
2
Oven Racks
3
Parts Needed
Check local codes and consult gas supplier. Check existing gas
supply and electrical supply. See the “Electrical Requirements”
and “Gas Supply Requirements” sections.
IMPORTANT: When the range is used under microwave models:
JMC82808CB-0, JMV9196CB-0, or YJMV9196CB-0, the Door
Baffle Plate Part Number W10737014 must be ordered and
used. Please reference the “Accessories” section of the User
Guide for contact information.
■ Pipe-joint compound
resistant to propane gas
■ 3/16" (4.8 mm) carbide-
tipped masonry drill bit
(for concrete/ceramic
floors)
■ Noncorrosive leak-
detection solution
For Propane/Natural Gas
Conversions
■ 5/8" (16 mm) combination
wrench
■ 3/8" (95 mm) nut driver
■ 9/32" (7 mm) nut driver
■ Masking tape
Optional Parts
To purchase these or any other accessories, please reference the
“Accessories” section of the User Guide for contact information.
■ Side Trim Kits:
5/8" (15.88 mm) White - Order Part Number W10675027
5/8" (15.88 mm) Black - Order Part Number W10675026
5/8" (15.88 mm) Stainless Steel - Order Part Number
W10675028
1
1
/
8
" (2.9 cm) White - Order Part Number W10731885
1¹⁄
8
" (2.9 cm) Black - Order Part Number W10731886
1¹⁄
8
" (2.9 cm) Stainless Steel - Order Part Number
W10731887
■ Backsplash Kits:
High 6" (15.2 cm) White - Order Part Number W10655448
High 6" (15.2 cm) Black - Order Part Number W10655449
High 6" (15.2 cm) Stainless Steel - Order Part Number
W10655450
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
Do not obstruct flow of combustion and ventilation air.
■ It is the installer’s responsibility to comply with installation
clearances specified on the model/serial/rating plate. The
model/serial/rating plate is located behind the oven door on
the top right-hand side of the oven frame.
■ The range should be located for convenient use in the
kitchen.
■ Recessed installations must provide complete enclosure of
the sides and rear of the range.
■ All openings in the wall or floor where range is to be installed
must be sealed.
■ Cabinet opening dimensions that are shown must be used.
Given dimensions are minimum clearances.
■ The anti-tip bracket must be installed. To install the anti-tip
bracket shipped with the range, see “Install Anti-Tip Bracket”
section.
■ Grounded electrical supply is required. See the “Electrical
Requirements” section.
■ Proper gas supply connection must be available. See the
“Gas Supply Requirements” section.
■ Contact a qualified floor covering installer to check that the
floor covering can withstand at least 200°F (93°C).
■ Use an insulated pad or 1/4" (6.4 mm) plywood under range
if installing range over carpeting.
IMPORTANT: To avoid damage to your cabinets, check with
your builder or cabinet supplier to make sure that the materials
used will not discolor, delaminate or sustain other damage. This
oven has been designed in accordance with the requirements
of UL and CSA International and complies with the maximum
allowable wood cabinet temperatures of 194°F (90°C).
5
Mobile Home - Additional Installation Requirements
The installation of this range must conform to the Manufactured
Home Construction and Safety Standard, Title 24 CFR,
Part 3280 (formerly the Federal Standard for Mobile Home
Construction and Safety, Title 24, HUD Part 280). When such
standard is not applicable, use the Standard for Manufactured
Home Installations, ANSI A225.1/NFPA 501A or with local codes.
In Canada, the installation of this range must conform with the
current standards CAN/CSA-A240-latest edition, or with local
codes.
Mobile Home Installations Require:
■ When this range is installed in a mobile home, it must be
secured to the floor during transit. Any method of securing
the range is adequate as long as it conforms to the
standards listed above.
Product Dimensions
These instructions cover several models. Your model may
appear different from the models depicted. Dimensions given are
maximum dimensions across all models.
Model WEG750
A. 1³⁄
16
" (3.0 cm) height from cooktop
to top of vent
B. 29
7
⁄
8
" (75.9 cm)
C. Model/serial/rating plate (located
behind the oven door on the top
right-hand side of the oven frame)
D. 36" (91.4 cm) height to top of
cooktop edge with leveling legs
screwed in all the way*
E. 27" (68.8 cm) max. depth
from front of console to
back of range
F. 28
5
/
8
" (72.7 cm) max. depth
from handle to back of
range
IMPORTANT: Range must be level after installation. Follow the
instructions in the “Level Range” section. Using the cooktop as a
reference for leveling the range is not recommended.
* Range can be raised approximately 1" (2.5 cm) by adjusting
the leveling legs.
A
B
D
E
F
C
6
Cabinet Dimensions
Cabinet opening dimensions shown are for 25" (64.0 cm) countertop depth, 24" (61.0 cm) base cabinet depth, and 36" (91.4 cm)
countertop height.
IMPORTANT: If installing a range hood or microwave hood combination above the range, follow the range hood or microwave hood
combination installation instructions for dimensional clearances above the cooktop surface.
Range may be installed next to combustible walls with zero clearance.
NOTE: When installed in a slide-in cutout, the front of oven door may protrude beyond the base cabinet.
Slide-In Cutout Freestanding Cutout
A. 18" (45.7 cm) upper side cabinet to countertop
B. 13" (33 cm) max. upper cabinet depth
C. 30" (76.2 cm) min. opening width
D. For minimum clearance to top of cooktop, see NOTE*.
E. 30" (76.2 cm) min. opening width
F. 3" (7.6 cm) min. clearance from both sides of range to side wall or
other combustible material
G. The shaded area is recommended for installation of rigid gas pipe
and grounded outlet.
H. 13¹⁄
8
" (33.3 cm)
I. 7¹¹⁄
16
" (19.5 cm)
J. 4¹³⁄
16
" (12.2 cm)
K. 3¹¹⁄
16
" (9.4 cm) plus measurement of N
L. 12" (30.5 cm)
M. Cabinet door or hinges should not extend into the cutout.
N. Remaining counter depth should not exceed 2¼" (5.7 cm)
A. 18" (45.7 cm) upper side cabinet to countertop
B. 13" (33 cm) max. upper cabinet depth
C. 30" (76.2 cm) min. opening width
D. For minimum clearance to top of cooktop, see NOTE*.
E. 30" (76.2 cm) min. opening width
F. 3" (7.6 cm) min. clearance from both sides of range to side wall or
other combustible material
G. The shaded area is recommended for installation of rigid gas pipe
and grounded outlet.
H. 13¹⁄
8
" (33.3 cm)
I. 7¹¹⁄
16
" (19.5 cm)
J. 4¹³⁄
16
" (12.2 cm)
K. 3¹¹⁄
16
" (9.4 cm)
L. 12" (30.5 cm)
M. Cabinet door or hinges should not extend into the cutout.
* NOTE: 24" (61.0 cm) minimum when bottom of wood or metal cabinet is shielded by not less than 1/4" (6.4 mm) flame retardant
millboard covered with not less than No. 28 MSG sheet steel, 0.015" (0.4 mm) stainless steel, 0.024" (0.6 mm) aluminum or 0.020"
(0.5 mm) copper.
30" (76.2 cm) minimum clearance between the top of the cooking platform and the bottom of an uncovered wood or metal cabinet.
M
A
B
C
D
E
F
H
I
J
L
K
G
M
A
B
C
D
E
F
H
I
J
L
K
G
N
7
Electrical Requirements
IMPORTANT: The range must be electrically grounded in
accordance with local codes and ordinances, or in the absence
of local codes, with the National Electrical Code, ANSI/NFPA 70
or Canadian Electrical Code, CSA C22.1.
This range is equipped with an electronic ignition system that will
not operate properly if plugged into an outlet that is not properly
polarized.
If codes permit and a separate ground wire is used, it is
recommended that a qualified electrical installer determine that
the ground path is adequate.
A copy of the above code standards can be obtained from:
National Fire Protection Association
1 Batterymarch Park
Quincy, MA 02169-7471
CSA International
8501 East Pleasant Valley Road
Cleveland, OH 44131-5575
■ A 120 volt, 60 Hz., AC only, 15-amp fused, ground and
polarized electrical circuit is required. A time-delay fuse or
circuit breaker is also recommended. It is recommended that
a separate circuit serving only this range be provided.
■ Electronic ignition systems operate within wide voltage limits,
but proper grounding and polarity are necessary. Check that
the outlet provides 120-volt power and is correctly grounded.
■ This gas range is not required to be plugged into a GFCI
(Ground-Fault Circuit Interrupter) outlet. It is recommended
that you not plug an electric spark ignition gas range or any
other major appliance into a GFCI wall outlet as it may cause
the GFCI to trip during normal cycling.
■ Performance of this range will not be affected if operated
on a GFCI-protected circuit. However, occasional nuisance
tripping of the GFCI breaker is possible due to the normal
operating nature of electronic gas ranges.
■ The tech sheet and wiring diagram are located on the back
of the range in a plastic bag.
NOTE: The metal chassis of the range must be grounded in
order for the control panel to work. If the metal chassis of the
range is not grounded, no keypads will operate. Check with
a qualified electrician if you are in doubt as to whether the
metal chassis of the range is grounded.
Gas Supply Requirements
Observe all governing codes and ordinances.
IMPORTANT: This installation must conform with all local codes
and ordinances. In the absence of local codes, installation must
conform with American National Standard, National Fuel Gas
Code ANSI Z223.1 — latest edition, or CAN/CGA B149 — latest
edition.
IMPORTANT: Leak testing of the range must be conducted
according to the manufacturer’s instructions.
Type of Gas
Natural Gas:
■ This range is factory-set for use with Natural gas. See the
“Gas Conversions” section. The model/serial/rating plate
located on the oven frame behind the top right-hand side of
the oven door has information on the types of gas that can
be used. If the types of gas listed do not include the type of
gas available, check with the local gas supplier.
Propane Gas Conversion:
Conversion must be done by a qualified service technician.
No attempt shall be made to convert the appliance from the gas
specified on the model/serial/rating plate for use with a different
gas without consulting the serving gas supplier. See the “Gas
Conversions” section.
Gas Supply Line
■ Provide a gas supply line of 3/4" (19 mm) rigid pipe to the
range location. A smaller size pipe on longer runs may
result in insufficient gas supply. With propane gas, piping or
tubing size can be 1/2" (13 mm) minimum. Usually, propane
gas suppliers determine the size and materials used in the
system.
NOTE: Pipe-joint compounds that resist the action of
propane gas must be used. Do not use TEFLON
®†
tape.
†
®
TEFLON is a registered trademark of Chemours.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
WARNING
Explosion Hazard
Use a new CSA International approved gas supply line.
Install a shut-off valve.
Securely tighten all gas connections.
If connected to propane, have a qualified person make
sure gas pressure does not exceed 14" (36 cm) water
column.
Examples of a qualified person include:
licensed heating personnel,
authorized gas company personnel, and
authorized service personnel.
Failure to do so can result in death, explosion, or fire.
8
Flexible Metal Appliance Connector:
■ If local codes permit, a new CSA design-certified, 4 to 5 ft
(122 to 152.4 cm) long, 1/2" or 3/4" (13 or 19 mm) I.D. (inside
diameter), flexible metal appliance connector may be used
for connecting range to the gas supply line.
■ A 1/2" (13 mm) male pipe thread is needed for connection to
the female pipe threads of the inlet to the appliance pressure
regulator.
■ Do not kink or damage the flexible metal tubing when
moving the range.
■ Must include a shut-off valve:
Install a manual gas line shut-off valve in an easily accessible
location. Do not block access to shut-off valve. The valve is
for turning on or shutting off gas to the cooktop.
A. Gas supply line
B. Shut-off valve open position
C. To range
Gas Pressure Regulator
The gas pressure regulator supplied with this range must be
used. The inlet pressure to the regulator should be as follows for
proper operation:
Natural Gas:
Minimum pressure: 15.2 cm WCP
Maximum pressure: 35.6 cm WCP
Propane Gas:
Minimum pressure: 27.9 cm WCP
Maximum pressure: 35.6 cm WCP
Contact local gas supplier if you are not sure about the inlet
pressure.
Burner Input Requirements
Input ratings shown on the model/serial/rating plate are for
elevations up to 2,000 ft (609.6 m).
For elevations above 2,000 ft (609.6 m), ratings are reduced at
a rate of 4% for each 1,000 ft (304.8 m) above sea level (not
applicable for Canada).
Gas Supply Pressure Testing
Gas supply pressure for testing regulator must be at least
2.5 cm water column pressure above the manifold pressure
shown on the model/serial/rating plate.
Line Pressure Testing Above 1/2 psi (3.5 kPa) Gauge
14" (35.6 cm WCP)
The range and its individual shut-off valve must be disconnected
from the gas supply piping system during any pressure testing of
that system at test pressures in excess of 1/2 psi (3.5 kPa).
Line Pressure Testing at 1/2 psi (3.5 kPa) Gauge
14" (35.6 cm WCP) or Lower
The range must be isolated from the gas supply piping
system by closing its individual manual shut-off valve during
any pressure testing of the gas supply piping system at test
pressures equal to or less than 1/2 psi (3.5 kPa).
A
B
C
9
INSTALLATION INSTRUCTIONS
Unpack Range Install Anti-Tip Bracket
1. Remove shipping materials, tape, and film from the range.
Keep cardboard bottom under range. Do not dispose of
anything until the installation is complete.
2. Remove oven racks and parts package from oven and
shipping materials.
3. To remove cardboard bottom, first take four cardboard
corners from the carton. Stack one cardboard corner on top
of another. Repeat with the other two corners. Place them
lengthwise on the floor behind the range to support the
range when it is laid on its back.
4. Using two or more people, firmly grasp the range and gently
lay it on its back on the cardboard corners.
5. Remove cardboard bottom.
The leveling legs can be adjusted while the range is on its back.
See the “Adjust Leveling Legs” section.
NOTE: To place range back up into a standing position, put a
sheet of cardboard or hardboard on the floor in front of range to
protect the flooring. Using two or more people, stand range back
up onto the cardboard or hardboard.
1. Remove the anti-tip bracket from the inside of the oven.
2. Determine which mounting method to use: floor or wall.
If you have a stone or masonry floor, you can use the wall
mounting method. If you are installing the range in a mobile
home, you must secure the range to the floor.
This anti-tip bracket and screws can be used with wood or
metal studs.
3. Determine and mark centerline of the cutout space. The
mounting bracket can be installed on either the left-hand
or right-hand side of the cutout. Position mounting bracket
against the wall in the cutout so that the V-notch of the
bracket is 12½" (31.8 cm) from centerline, as shown.
A. 12½" (31.8 cm)
B. Bracket V-notch
WARNING
Excessive Weight Hazard
Use two or more people to move and install range.
Failure to do so can result in back or other injury.
WARNING
Tip Over Hazard
A child or adult can tip the range and be killed.
Install anti-tip bracket to floor or wall per installation
instructions.
Slide range back so rear range foot is engaged in the
slot of the anti-tip bracket.
Re-engage anti-tip bracket if range is moved.
Do not operate range without anti-tip bracket installed
and engaged.
Failure to follow these instructions can result in death
or serious burns to children and adults.
Centerline
A
B
10
4. Drill two 1/8" (3 mm) holes that correspond to the bracket
holes of the determined mounting method. See the following
illustrations.
Floor Mounting
Rear position Front position Diagonal (2 options)
Wall Mounting
5. Using the two #10 x 1
5
⁄
8
" (41 mm) Phillips-head screws
provided, mount anti-tip bracket to the wall or floor.
6. Move range close enough to opening to allow for final
electrical connections. Remove shipping base, cardboard or
hardboard from under range.
7. Move range into its final location, making sure rear leveling
leg slides into anti-tip bracket.
8. Move range forward onto shipping base, cardboard, or
hardboard to continue installing the range, using the
following installation instructions.
Adjust Leveling Legs
1. If range height adjustment is necessary, use a wrench or
pliers to loosen the four leveling legs.
This may be done with the range on its back or with the
range supported on two legs after the range has been placed
back to a standing position.
NOTE: To place range back up into a standing position, put a
sheet of cardboard or hardboard in front of range. Using two
or more people, stand range back up onto the cardboard or
hardboard.
2. Measure the distance from the top of the counter to the floor.
3. Measure the distance from the top of the cooktop to the
bottom of the leveling legs. This distance should be the
same. If it is not, adjust the leveling legs to the correct
height. The leveling legs can be loosened to add up to a
maximum of 1" (2.5 cm). A minimum of 3/16" (5 mm) is
needed to engage the anti-tip bracket.
NOTE: If height adjustment is made when range is standing,
tilt the range back to adjust the front legs, and then tilt
forward to adjust the rear legs.
4. When the range is at the correct height, check that there is
adequate clearance under the range for the anti-tip bracket.
Before sliding range into its final location, check that the
antitip bracket will slide under the range and onto the rear
leveling leg prior to anti-tip bracket installation.
NOTE: If a Trim Kit will be used, the top of the cooktop
should be higher than the counter. See the Installation
Instructions included with the Trim Kit for the correct height.
WARNING
Tip Over Hazard
A child or adult can tip the range and be killed.
Install anti-tip bracket to floor or wall per installation
instructions.
Slide range back so rear range foot is engaged in the
slot of the anti-tip bracket.
Re-engage anti-tip bracket if range is moved.
Do not operate range without anti-tip bracket installed
and engaged.
Failure to follow these instructions can result in death
or serious burns to children and adults.
11
Level Range
1. Place level on the oven bottom, as indicated in one of the
two figures below, depending on the size of the level. Check
with the level side to side and front to back.
2. If range is not level, use a wrench or pliers to adjust leveling
legs up or down until the range is level.
NOTE: Range must be level for satisfactory baking
performance and best cleaning results using AquaLift
®
Self-Clean Technology.
Make Gas Connection
This range is factory-set for use with Natural gas. To use this
range with propane gas, see the “Gas Conversions” section
before connecting this range to the gas supply. Gas conversions
from Natural gas to Propane gas or from Propane gas to Natural
gas must be done by a qualified installer.
Typical Flexible Connection
1. Apply pipe-joint compound made for use with propane gas
to the smaller thread ends of the flexible connector adapters.
See B and G in the following illustration.
2. Attach one adapter to the gas pressure regulator and
the other adapter to the gas shut-off valve. Tighten both
adapters, being certain not to move or turn the gas pressure
regulator.
3. Use a 15/16" (24 mm) combination wrench and an adjustable
wrench to attach the flexible connector to the adapters.
IMPORTANT: All connections must be wrench-tightened.
Do not make connections to the gas regulator too tight.
Making the connections too tight may crack the regulator
and cause a gas leak. Do not allow the regulator to turn
when tightening fittings.
A. Gas pressure regulator
B. Use pipe-joint compound.
C. Adapter (must have 1/2"
[13 mm] male pipe thread)
D. Flexible connector
E. Manual gas shut-off valve
F. 1/2" (13 mm) or 3/4" (19 mm)
gas pipe
G. Use pipe-joint compound.
H. Adapter
Complete Connection
1. Check that the gas pressure regulator shut-off valve is in the
on position.
A. Gas pressure regulator shut-off valve
shown in the “on” position
2. Open the manual shut-off valve in the gas supply line. The
valve is open when the handle is parallel to the gas pipe.
A. Closed valve
B. Open valve
3. Test all connections by brushing on an approved
noncorrosive leak-detection solution. If bubbles appear, a
leak is indicated. Correct any leak found.
A
B
C
D
E
FG
H
A
A
B
WARNING
Explosion Hazard
Use a new CSA International approved gas supply line.
Install a shut-off valve.
Securely tighten all gas connections.
If connected to propane, have a qualified person make
sure gas pressure does not exceed 14" (36 cm) water
column.
Examples of a qualified person include:
licensed heating personnel,
authorized gas company personnel, and
authorized service personnel.
Failure to do so can result in death, explosion, or fire.
12
4. Remove cooktop burner caps and bases from package
containing parts. Place the burner bases as indicated by the
following illustration for your model:
For Models WEG750H0H and WEGA25H0H:
5. Align the gas tube opening in the burner base with the orifice
holder on the cooktop and the igniter electrode with the
notch in the burner base.
A. Burner cap
B. Gas tube opening
C. Burner base
D. Igniter electrode
E. Orifice holder
6. Place the burner caps on the appropriate burner bases.
IMPORTANT: The bottom of the small and medium caps are
different. Do not put the wrong size burner cap on the burner
base.
Small cap Medium cap Wok cap X-Large cap
Burner caps should be level when properly positioned. If burner
caps are not properly positioned, surface burners will not
light. The burner cap should not rock or wobble when properly
aligned.
A. Incorrect
B. Correct
7. Plug into a grounded 3 prong outlet.
A
B
C
D
E
A
B
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
WARNING
A
D
EB
C
AUX
SR
UR
A. Small
B. X-Large
C. Oval D. Medium
E. Large
13
Verify Anti-Tip Bracket Is Installed
and Engaged
On Ranges Equipped with a Premium Storage Drawer:
1. Slide range into final location, making sure rear leveling leg
slides into anti-tip bracket.
2. Remove the premium storage drawer. See the “Remove/
Replace Drawer” section.
3. Use a flashlight to look underneath the bottom of the range.
4. Visually check that the rear range foot is inserted into the slot
of the anti-tip bracket.
On Ranges Equipped with a Warming Drawer or Baking
Drawer:
1. Slide range into final location, making sure rear leveling leg
slides into anti-tip bracket. Leave a 1" (2.5 cm) gap between
the back of the range and the back wall.
2. Place the outside of your foot against the bottom front of the
warming drawer or baking drawer to keep the range from
moving, and then grasp the back of the range, as shown.
3. Slowly attempt to tilt the range forward.
If you encounter immediate resistance, the range foot is
engaged in the anti-tip bracket. Go to Step 8.
4. If the rear of the range lifts more than 1/2" (1.3 cm) off the
floor without resistance, stop tilting the range and lower it
gently back to the floor. The range foot is not engaged in the
anti-tip bracket.
IMPORTANT: If there is a snapping or popping sound when
lifting the range, the range may not be fully engaged in the
bracket. Check to see if there are obstructions keeping
the range from sliding to the wall or keeping the range foot
from sliding into the bracket. Verify that the bracket is held
securely in place by the mounting screws.
5. Slide the range forward, and verify that the anti-tip bracket is
securely attached to the floor or wall.
6. Slide range back so the rear range foot is inserted into the
slot of the anti-tip bracket.
7. Repeat steps 1 and 2 to ensure that the range foot is
engaged in the anti-tip bracket.
If the rear of the range lifts more than 1/2" (1.3 cm) off the
floor without resistance, the anti-tip bracket may not be
installed correctly. Do not operate the range without anti-
tip bracket installed and engaged. Please reference the
“Warranty” section of the User Guide to contact service.
Install Griddle
1. Place the "FRONT" end of the griddle down, facing the oven
door. Verify that the lugs are placed onto the grate.
2. Clean the griddle before using. Refer to the Use and Care
Guide for cleaning instructions. The griddle can be placed
over the left, right, or center burner.
Front
Lugs
14
8. Move the range into its final location. Check that the range
is level by placing a level on the oven bottom. See the “Level
Range” section.
IMPORTANT: If the range is moved to adjust the leveling
legs, verify that the anti-tip bracket is engaged by repeating
steps 1 to 8.
Electronic Ignition System
Initial Lighting and Gas Flame Adjustments
Cooktop and oven burners use electronic igniters in place of
standing pilots. When the cooktop control knob is turned to the
ignite position, the system creates a spark to light the burner. All
cooktop burners will spark, but only the burner with the control
knob turned to the ignite position will produce a flame. This
sparking continues as long as the control knob is turned to the
ignite position.
When the oven control is turned to the desired setting, sparking
occurs and ignites the gas.
Check Operation of Cooktop Burners
Standard Surface Burners
Push in and turn each control knob to the ignite position.
The flame should light within 4 seconds. The first time a burner
is lit, it may take longer than 4 seconds to light because of air in
the gas line.
If Burners Do Not Light Properly:
■ Turn cooktop control knob to the off position.
■ Check that the range is plugged into a grounded 3 prong
outlet. Check that the circuit breaker has not tripped or the
household fuse has not blown.
■ Check that the gas shut-off valves are set to the open
position.
■ Check that burner caps are properly positioned on burner
bases.
Repeat start-up. If a burner does not light at this point, turn
the control knobs to the off position and contact your dealer or
authorized service company for assistance. Please reference the
“Warranty” section of the User Guide to contact service
If the cooktop “low” burner flame needs to be adjusted for any
of the burners, see the “Adjust Flame Height” section.
Check Operation of Oven Bake Burner
1. Press BAKE.
2. Press the Start pad.
The oven burner should light within 8 seconds. The first time
a burner is lit, it may take longer than 8 seconds to light
because of air in the gas line.
3. After 2 minutes, open the oven door and check that the oven
is warm.
If Burner Does Not Light Properly:
■ Press the Off pad.
■ Check that the range is plugged into a grounded 3 prong
outlet. Check that the circuit breaker has not tripped or the
household fuse has not blown.
■ Check that the gas shut-off valves are set to the open
position.
Repeat steps 1 to 3. If the burner does not light at this point,
press the off pad and contact your dealer or authorized service
company for assistance. Please reference the “Warranty” section
of the User Guide to contact service
If the bake burner flame needs to be adjusted, see the “Adjust
Flame Height” section.
Refer to the User Guide for proper operation of the oven
controls.
Check Operation of Oven Broil Burner
1. Close the oven door.
2. Press BROIL.
3. Press the Start pad.
The oven burner should light within 8 seconds. The first time
a burner is lit, it may take longer than 8 seconds to light
because of air in the gas line.
4. After 2 minutes, open the oven door and check that the oven
is warm.
If Burner Does Not Light Properly:
■ Press the Off pad.
■ Check that the range is plugged into a grounded 3 prong
outlet. Check that the circuit breaker has not tripped or the
household fuse has not blown.
■ Check that the gas shut-off valves are set to the open
position.
Repeat steps 1 to 3. If the burner does not light at this point,
press the off pad and contact your dealer or authorized service
company for assistance. Please reference the “Warranty” section
of the User Guide to contact service
If the broil burner flame needs to be adjusted, see the “Adjust
Flame Height” section.
Refer to the User Guide for proper operation of the oven
controls.
Remove/Replace Drawer
(on some models)
Remove all items from inside the baking drawer, warming drawer
or premium storage drawer, and then allow the range to cool
completely before attempting to remove the drawer.
To Remove:
1. Open the drawer to its fully open position.
2. Using a flat-blade screwdriver, gently loosen the drawer
from the glide alignment notch, and then lift up the drawer
alignment tab from the glide.
A. Flat-blade screwdriver
B. Drawer alignment tab
C. Drawer glide notch
3. Repeat Step 2 on the other side. The drawer is no longer
attached to the drawer glides. Using both hands, pick up the
drawer to complete the removal.
C
A
B
15
To Replace:
1. Insert both hanger arms into the door. Be sure that the hinge
notches are engaged in the oven door frame.
A. Hinge notch
2. Open the oven door.
The door should be able to open all the way.
3. Move the hinge levers back to the locked position. Check
that the door is free to open and close and is level while
closed. If it is not, repeat the removal and installation
procedures.
Complete Installation
1. Check that all parts are now installed. If there is an extra
part, go back through the steps to see which step was
skipped.
2. Check that you have all of your tools.
3. Check that you have all of the range accessories, especially
oven racks. These accessories may be in the range
packaging.
4. Dispose of/recycle all packaging materials.
5. Check that the range is level. See the “Level Range” section.
6. Use a mild solution of liquid household cleaner and warm
water to remove waxy residue caused by shipping material.
Dry thoroughly with a soft cloth. For more information, see
the “Range Care” section of the User Guide.
7. Read the User Guide.
8. Turn on surface burners and oven. See the User Guide for
specific instructions on range operation.
NOTE: Odors and smoke are normal when the oven is used
the first few times.
If Range Does Not Operate, Check the Following:
■ Household fuse is intact and tight, or circuit breaker has not
tripped.
■ Gas pressure regulator shut-off valve is in the open position.
■ Range is plugged into a grounded 3 prong outlet.
■ Electrical supply is connected.
9. When the range has been on for 5 minutes, check for heat.
If the range is cold, turn off the range and check that the gas
supply line shut-off valve is open.
■ If the gas supply line shut-off valve is closed, open it, and
then repeat the 5-minute test as outlined above.
■ If the gas supply line shut-off valve is open, close it, and
contact a qualified technician.
If You Need Assistance or Service:
Please reference the “Warranty” section of the User Guide to
contact service.
A
To Replace:
1. Align the forward drawer notches with the notches in the
drawer glides on both sides. Place the rear alignment tabs
into the drawer glides on both sides.
A. Drawer alignment tab
B. Drawer glide notch
2. Push the drawer in all the way.
3. Gently open and close the drawer to ensure it is seated
properly on the glides on both sides.
Oven Door
For normal range use, it is not suggested to remove the oven
door. However, if removal is necessary, make sure the oven is
off and cool. Then, follow these instructions. The oven door is
heavy.
To Remove:
1. Open oven door all the way.
2. Pinch the hinge latch between two fingers and pull forward.
Repeat on other side of oven door.
A. Hinge latch
3. Close the oven door as far as it will shut.
4. Lift the oven door while holding both sides.
Continue to push the oven door closed and pull it away from
the oven door frame.
A
B
A
16
GAS CONVERSIONS
Gas conversions from Natural gas to Propane gas or from
Propane gas to Natural gas must be done by a qualified installer.
Propane Gas Conversion
1. Turn the manual shut-off valve to the closed position.
A. Gas supply line
B. Manual shut-off valve closed position
C. To range
2. Unplug range or disconnect power.
To Convert Gas Pressure Regulator (Natural Gas to
Propane Gas)
1. Remove the premium storage drawer, warming drawer or
baking drawer. See the “Remove/Replace Drawer” section.
2. Locate gas pressure regulator at rear of the drawer
compartment.
NOTE: On models with a warming drawer or baking drawer,
an access cover must be removed to access the gas
pressure regulator.
A. Gas pressure regulator
IMPORTANT: Do not remove the gas pressure regulator.
WARNING
Tip Over Hazard
A child or adult can tip the range and be killed.
Install anti-tip bracket to floor or wall per installation
instructions.
Slide range back so rear range foot is engaged in the
slot of the anti-tip bracket.
Re-engage anti-tip bracket if range is moved.
Do not operate range without anti-tip bracket installed
and engaged.
Failure to follow these instructions can result in death
or serious burns to children and adults.
A
B
C
A
WARNING
Explosion Hazard
Use a new CSA International approved gas supply line.
Install a shut-off valve.
Securely tighten all gas connections.
If connected to propane, have a qualified person make
sure gas pressure does not exceed 14" (36 cm) water
column.
Examples of a qualified person include:
licensed heating personnel,
authorized gas company personnel, and
authorized service personnel.
Failure to do so can result in death, explosion, or fire.
17
3. Remove plastic cover from gas pressure regulator cap.
4. Turn gas pressure regulator cap counterclockwise with a
5/8" (16 mm) combination wrench to remove.
NOTE: Do not remove the spring beneath the cap.
A. Plastic cover
B. Gas pressure regulator cap with solid end facing out
C. Gas pressure regulator cap with hollow end facing out
D. Washer
E. Gas pressure regulator cap
5. Turn over the gas pressure regulator cap and reinstall on
regulator so that the hollow end faces out and the marking
“LP” is facing the direction shown in the above drawing.
6. Replace plastic cover over gas pressure regulator cap.
To Convert Surface Burners (Natural Gas to Propane
Gas)
1. Remove burner cap.
2. Remove the burner base.
A. Igniter electrode
B. Burner cap
C. Gas tube opening
D. Burner base
3. Apply masking tape to the end of a 9/32" (7 mm) nut driver
to help hold the gas orifice spud in the nut driver while
changing it. Press nut driver down onto the gas orifice spud
and remove by turning it counterclockwise and lifting out.
Set gas orifice spud aside.
A. Igniter electrode
B. Orifice spud
C. Orifice spud holder
D. Screws
4. Remove the orifice spuds shipped in the literature package
in the oven. Gas orifice spuds are stamped with a number,
marked with 1 or 2 color dots, and have a groove in the hex
area. Replace the Natural gas orifice spud with the correct
Propane gas orifice spud.
A. Propane groove
Refer to the following chart for correct Propane gas orifice
spud ratings and to spud holder card for proper placement.
Propane Gas Orifice Spud Chart for Surface Burners
Burner
Rating/Type
Color Size
(mm)
ID
Number
Placement
13,500 BTU 1.55 L155 LF
4,500 BTU 0.61 L61 LR
13,500 BTU 1.06 L106 RF
7,500 BTU Red/Blue 0.80 L80 RR
10,000 BTU 0.92 L92 CTR
NOTE: Refer to the model/serial/rating plate located on the oven
frame behind the top right-hand side of the oven door for proper
sizing of spuds for each burner location.
5. Place Natural gas orifice spuds in the orifice spud bag.
IMPORTANT: Keep the Natural gas orifice spuds in case of
reinstallation with Natural gas.
6. Replace the burner base.
7. Replace burner cap.
8. Repeat steps 1 to 7 for the remaining burners.
To Convert Oven Bake Burner (Natural Gas to
Propane Gas)
1. Remove the oven racks and the oven door. See the “Oven
Door” section.
2. Remove two screws and washers at the rear of the oven
bottom.
3. Lift the rear of the oven bottom up and back until the front of
the panel is away from the front frame. Remove from oven
and set it aside on a covered surface.
A. Screws
B. Oven bottom
A
B
C
D
Side view before
Side view after
E
NG
LP
NG
LP
A
B
C
D
D
A
B
C
A
A
B
18
4. Remove two screws from the bake burner.
5. Slide the front of the bake burner to the side to remove
tab from front of oven. Lift the back of the bake burner off
the oven orifice, and set the bake burner aside. Do not
disconnect the wire.
A. Bake burner
B. Screws
A. Oven orifice
6. Apply masking tape to the end of a 3/8" (9.5 mm) nut driver
to help hold the gas orifice spud in the nut driver while
changing it. Press nut driver down onto the gas orifice spud
and remove by turning the Natural gas bake burner orifice
spud counterclockwise to remove. The spud will be stamped
with a “47.”
7. Replace the “47” spud with a “56” spud. Install the Propane
gas bake burner orifice spud, turning it clockwise until snug.
IMPORTANT: Do not overtighten.
A. Orifice spud
8. Position the back of the bake burner over the oven orifice,
and then align the holes for the screws.
9. Reattach the bake burner with two screws.
10. Position the front of the oven bottom panel toward the front
frame, and then lower the rear of the oven bottom panel into
the oven.
11. Reattach the oven bottom panel with two screws and
2 washers.
To Convert Oven Broil Burner (Natural Gas to
Propane Gas)
1. Remove the one screw from the broil burner.
2. Remove the flame spreader.
3. Remove the broil burner from the broil burner orifice hood.
NOTE: The broil burner will hang in the back of the oven
while you are changing the orifice hood.
4. Apply masking tape to the end of a 3/8" (9.5 mm) nut driver
to help hold the gas orifice spud in the nut driver while
changing it. Press nut driver down onto the gas orifice spud
and remove by turning the Natural gas broil burner orifice
hood counterclockwise to remove. The hood will be stamped
with a “155.”
5. Replace the “155” hood with a “100” hood. Install the
Propane gas broiler burner orifice hood, turning it clockwise
until snug.
IMPORTANT: Do not overtighten.
A. Orifice hood
A. Broil burner
B. Flame spreader
C. Screws
D. Orifice hood
C
D
A
B
A
A
B
x.xx
A
A
19
6. Place the broil burner on the broil burner orifice hood. Insert
the broil burner ceramic igniter in the hole in the rear of the
oven.
7. Replace the flame spreader with all four tabs facing up and
the notches toward the rear of the oven.
8. Position the broil burner against the top of the oven and
attach it with one screw.
9. Replace premium storage drawer, warming drawer or baking
drawer. See the “Remove/Replace Drawer” section.
10. Replace the oven door. See the “Oven Door” section.
11. Replace the oven racks.
Complete Installation (Natural Gas to Propane Gas)
1. Refer to the “Make Gas Connection” section for proper
connection of the range to the gas supply.
2. Refer to the “Electronic Ignition System” section for proper
burner ignition and operation.
3. Refer to the “Adjust Flame Height” section for burner flame
adjustments.
IMPORTANT: You may have to adjust the low setting for
each cooktop burner.
Checking for proper cooktop flame is very important. The
small inner cone should have a very distinct blue flame 1/4"
to 1/2" (6.4 to 13 mm) long. The outer cone is not as distinct
as the inner cone. Propane gas flames have a slightly yellow
tip.
4. Refer to “Complete Installation” in the “Installation
Instructions” section of these instructions to complete this
procedure.
Natural Gas Conversion
1. Turn the manual shut-off valve to the closed position.
A. Gas supply line
B. Manual shut-off valve closed position
C. To range
2. Unplug range or disconnect power.
To Convert Gas Pressure Regulator (Propane Gas to
Natural Gas)
1. Remove the premium storage drawer, warming drawer or
baking drawer. See the “Remove/Replace Drawer” section.
2. Locate gas pressure regulator at rear of the drawer
compartment.
NOTE: On models with a warming drawer or baking drawer,
an access cover must be removed to access the gas
pressure regulator.
A. Gas pressure regulator
IMPORTANT: Do not remove the gas pressure regulator.
3. Remove plastic cover from gas pressure regulator cap.
IMPORTANT: Make sure to save the orifices that have
just been replaced in the conversion.
WARNING
Tip Over Hazard
A child or adult can tip the range and be killed.
Install anti-tip bracket to floor or wall per installation
instructions.
Slide range back so rear range foot is engaged in the
slot of the anti-tip bracket.
Re-engage anti-tip bracket if range is moved.
Do not operate range without anti-tip bracket installed
and engaged.
Failure to follow these instructions can result in death
or serious burns to children and adults.
A
B
C
A
20
4. Turn gas pressure regulator cap counterclockwise with a 5/8"
(16 mm) combination wrench to remove.
NOTE: Do not remove the spring beneath the cap.
A. Plastic cover
B. Gas pressure regulator cap with hollow end facing out
C. Gas pressure regulator cap with solid end facing out
D. Washer
E. Gas pressure regulator cap
5. Turn over the gas pressure regulator cap and reinstall on
regulator so that the solid end faces out and the marking
“NG” is facing the direction shown in the above drawing.
6. Replace plastic cover over gas pressure regulator cap.
To Convert Surface Burners (Propane Gas to Natural
Gas)
1. Remove burner cap.
2. Remove the burner base.
A. Igniter electrode
B. Burner cap
C. Gas tube opening
D. Burner base
3. Apply masking tape to the end of a 9/32" (7 mm) nut driver
to help hold the gas orifice spud in the nut driver while
changing it. Press nut driver down onto the gas orifice spud
and remove by turning it counterclockwise and lifting out.
Set gas orifice spud aside.
A. Igniter electrode
B. Orifice spud
C. Orifice spud holder
D. Screws
4. Gas orifice spuds are stamped with a number on the side.
Replace the Propane gas orifice spud with the correct
Natural gas orifice spud.
A. Stamped number
Refer to the following chart for the correct Natural gas orifice
spud placement.
Natural Gas Orifice Spud Chart
Burner Rating Color Size (mm) ID
Number
17,000 BTU Orange 1.90 190
5,000 BTU Purple 1.00 100
13,000 BTU 1.65 165
9,500 BTU Black 1.35 135
10,000 BTU 1.40 140
NOTE: Refer to the model/serial/rating plate located on the oven
frame behind the top right-hand side of the oven door for proper
sizing of spuds for each burner location.
5. Place Propane gas orifice spuds in the orifice spud bag.
IMPORTANT: Keep the Propane gas orifice spuds in case of
reinstallation with Propane gas.
6. Replace the burner base.
7. Replace burner cap.
8. Repeat steps 1 to 7 for the remaining burners.
To Convert Oven Bake Burner (Propane Gas to
Natural Gas)
1. Remove the oven racks and the oven door. See the “Oven
Door” section.
2. Remove two screws and washers at the rear of the oven
bottom.
3. Lift the rear of the oven bottom up and back until the front of
the panel is away from the front frame. Remove from oven
and set it aside on a covered surface.
A. Screws
B. Oven bottom
A
B
C
D
Side view before
Side view after
E
NG
LP
LP
NG
A
B
C
D
D
A
B
C
A
A
B
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
Whirlpool WEGA25H0HZ Guide d'installation
- Catégorie
- Cuisinières
- Taper
- Guide d'installation