LG Washing Machine [WT7100C] Manuel utilisateur

ESPAÑOLENGLISH FRANÇAIS

OWNER'S MANUAL

WASHING

MACHINE

Read this owner's manual thoroughly before operating the appliance and keep it handy

for reference at all times.

WT7100C*

MFL68267032

Rev.00_022318

www.lg.com

2

TABLE OF CONTENTS

3 SAFETY INSTRUCTIONS

3 IMPORTANT SAFETY INSTRUCTIONS

7 PRODUCT OVERVIEW

7 Parts

7 Accessories

8 INSTALLATION

8 Tools Needed

8 Installation Overview

9 Product Specifications

10 Choosing the Proper Location

11 Unpacking and Removing Shipping Material

12 Connecting the Water Lines

13 Connecting the Drain Hose

14 Leveling the Washer

15 Connecting to the Power Supply

15 Testing the Washer

16 OPERATION

16 Using the Washer

17 Sorting Laundry

18 Loading the Washer

19 Adding Cleaning Products

22 Control Panel

24 Wash Cycles

26 Cycle Guide

27 Cycle Modifier Buttons

28 Option Buttons

30 SMART FUNCTIONS

30 Smart Diagnosis™ Function

31 MAINTENANCE

31 Regular Cleaning

33 Cleaning the Water Inlet Filters

34 Care in Cold Climates

35 TROUBLESHOOTING

35 Before Calling for Service

42 LIMITED WARRANTY

42 FOR USA

45 FOR CANADA

49 Warranty Exceptions (U.S. and Canada)

3SAFETY INSTRUCTIONS

ENGLISH

SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and

follow all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or injure you and others.

All safety messages will follow the safety alert symbol and either the word WARNING or CAUTION.

These words mean:

WARNING

If you do not follow instructions, it could result in death or serious injury.

CAUTION

If you do not follow instructions, it could result in minor or moderate injury or damage to the product.

All safety messages tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell

you what may happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING

To reduce the risk of explosion, re, death, electric shock, scalding or injury

to persons when using this product, follow basic precautions, including the

following:

California Safe Drinking Water and Toxic Enforcement Act

• This product contains chemicals known to the State of California to cause cancer and birth defects or other

reproductive harm. Wash hands after handling. (USA only)

INSTALLATION

• Adhere to all industry recommended safety procedures including the use of long-sleeved gloves and safety

glasses.

• Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has

missing or broken parts, including a damaged cord or plug.

• Before use, the appliance must be properly installed as described in this manual.

• To reduce the risk of severe injury or death, follow all installation instructions.

• Refer to the INSTALLATION INSTRUCTIONS for detailed grounding procedures. Installation instructions

are packed with the appliance for the installer’s reference. If the appliance is moved to a new location, have

it checked and reinstalled by qualied service personnel.

• Moving or installation of the appliance requires two or more people.

• Do not install the appliance in humid spaces.

• Store and install the appliance where it will not be exposed to temperatures below freezing or exposed to

outdoor weather conditions.

• This appliance is not designed for maritime use or for mobile installations such as in RVs, trailers, or aircraft.

4 SAFETY INSTRUCTIONS

• Keep packing materials out of the reach of children. Packaging material can be dangerous for children.

There is a risk of suffocation.

• Destroy the carton, plastic bag, and other packing materials after the appliance is unpacked. Children might

use them for play. Cartons covered with rugs, bedspreads, or plastic sheets can become airtight chambers.

• The appliance must be installed and electrically grounded by qualied service personnel in accordance with

local codes.

• Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

• When installing or moving the appliance, be careful not to pinch, crush, or damage the power cord.

• Connect to a properly rated, protected, and sized power circuit to avoid electrical overload.

• This appliance must be positioned near to an electrical power supply.

• Disconnect the power cord, house fuse or circuit breaker before installing or servicing the appliance.

• The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard

3-prong (grounding) wall outlet to minimize the possibility of electric shock from this appliance.

• Use new hoses when connecting the appliance to the water supply. Do not reuse old hoses.

OPERATION

• Read all instructions before using the appliance and save these instructions.

• Use this appliance only for its intended purpose.

• If the product has been submerged, contact an LG Electronics customer information center for instructions

before resuming use.

• If you detect a strange sound, a chemical or burning smell, or smoke coming from the appliance, unplug it

immediately, and contact an LG Electronics customer information center.

• Under certain conditions, hydrogen gas may be produced in a hot-water system that has not been used

for two weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot-water system has not been used for

such a period, before using the appliance turn on all hot water faucets and let the water ow from each for

several minutes. This will release any accumulated hydrogen gas. As the gas is ammable, do not smoke or

use an open ame during this time.

• Do not reach into the washer if the tub or drum, agitator, or any interior parts are moving. Before loading,

unloading, or adding items, press Start/Pause and allow the tub or drum to coast to a complete stop before

reaching inside.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge, unless they have been given supervision or

instruction concerning the use of the appliance by a person responsible for their safety.

• Do not allow children or pets to play on, in or with the appliance. Close supervision is necessary when the

appliance is used near children or pets.

• Keep laundry products out of children’s reach. To prevent injury to persons, observe all warnings on product

labels.

• Repair or immediately replace all power cords that have become frayed or otherwise damaged. Do not use

a cord that shows cracks or abrasion damage along its length or at either end.

• Never unplug the appliance by pulling on the power cord. Always grip the plug rmly and pull straight out

from the outlet.

• Do not use an extension cord or adapter with this appliance.

• Do not grasp the power cord or touch the appliance controls with wet hands.

• Do not modify or extend the power cord.

5SAFETY INSTRUCTIONS

ENGLISH

• If the electrical supply cord is damaged, it must only be replaced by the manufacturer or its service agent or

a similar qualied person in order to avoid a hazard.

• Do not put oily or greasy clothing, candles or ammable materials on top of the appliance.

• Keep the area underneath and around your appliances free of combustible materials (lint, paper, rags, etc.),

gasoline, chemicals and other ammable vapors and liquids.

• Do not store or use gasoline or other ammable vapors and liquids in the vicinity of this or any other

appliance.

• Do not mix chlorine bleach with ammonia or acids such as vinegar. Follow package directions when using

laundry products. Incorrect usage can produce poisonous gas, resulting in serious injury or death.

• Never use harsh chemicals, abrasive cleaners, or solvents to clean the washer. They will damage the nish.

• Do not wash articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline,

dry-cleaning solvents, vegetable or cooking oil, or other ammable or explosive substances, as they give off

vapors that could ignite or explode.

• Do not add gasoline, dry cleaning solvents, or other ammable or explosive substances to the wash water.

These substances give off vapors that could ignite or explode.

• In the event of a gas leak (propane gas, LP gas, etc.) do not operate this or any other appliance. Open a

window or door to ventilate the area immediately.

• Do not tamper with controls.

• Fix the drain hose securely in place to avoid ooding.

• Do not abuse, sit on, or stand on the lid (door) of the appliance.

• Keep hands and foreign objects clear of the lid (door) and latch area when closing the lid (door).

• Always check the inside of the appliance for foreign objects.

MAINTENANCE

• Do not repair or replace any part of the appliance. All repairs and servicing must be performed by qualied

service personnel unless specically recommended in this owner’s manual. Use only authorized factory

parts.

• Disconnect this appliance from the power supply before cleaning and attempting any user maintenance.

Turning the controls to the OFF position does not disconnect this appliance from the power supply.

• Remove any dust or foreign matter from the power plug pins.

• Do not disassemble or repair the appliance by yourself.

• Remove the lid (door) before the appliance is removed from service or discarded to avoid the danger of

children or small animals getting trapped inside.

• Make sure the dispenser drawer or lid (door) is closed at all times when not being lled with laundry

products.

GROUNDING INSTRUCTIONS

• Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with

a qualied electrician or service personnel if you are in doubt whether the appliance is properly grounded.

Do not modify the plug provided with the appliance; if it will not t the outlet, have a proper outlet installed by

a qualied electrician.

• The appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk

of electric shock by providing a path of least resistance for electric current. The appliance is equipped with

a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an

appropriate outlet that is installed and grounded in accordance with all local codes and ordinances.

6 SAFETY INSTRUCTIONS

CAUTION

To reduce the risk of minor or moderate injury to persons, malfunction, or damage

to the product or property when using this product, follow basic precautions,

including the following:

INSTALLATION

• Install the product on a rm and level oor.

OPERATION

• Do not place objects on top of the appliance.

• Turn off the water faucets and unplug the appliance if the appliance is to be left for an extended period of

time, such as during vacations.

• ALWAYS follow the fabric care instructions supplied by the garment manufacturer.

• Use fabric softeners or products to eliminate static only as recommended by the manufacturer.

• Do not combine laundry products for use in one load unless specied on the label.

• Do not touch draining water which may be hot.

• If the drain hose and the water supply hose are frozen in winter, defrost before using the appliance.

• Do not store or spill liquid detergents, cleaners, or bleaches (chlorine bleach, oxygen bleach) on the

appliance. Doing so may result in corrosion, discoloration or damage to the surface of the appliance.

• Clothing or articles that are waterproof or water resistant must be washed in the Waterproof cycle only.

(e.g. water resistant clothing, mattress covers, outdoor clothes, plastic mats, etc.) Otherwise, it may result

in personal injury or damage to the washer, clothes, walls, oor, and surrounding objects due to abnormal

vibration.

SAVE THESE INSTRUCTIONS

7PRODUCT OVERVIEW

ENGLISH

PRODUCT OVERVIEW

Parts

9

1

Detergent Dispenser

3

Tub

5

Control Panel

7

Water Inlets

2

Liquid Bleach

Compartment

4

Lid (Door)

6

Leveling Feet

8

Power Cord

9

Drain Hose

Accessories

Included Accessories

Tie Strap

Required Accessories

Hot and Cold Water Hoses

NOTE

• The images in this guide may be different from the actual components and accessories, which are subject to

change by the manufacturer without prior notice for product improvement purposes.

• For your safety and for extended product life, use only authorized components. The manufacturer is not

responsible for product malfunction or accidents caused by the use of separately purchased unauthorized

components or parts.

8 INSTALLATION

INSTALLATION

Tools Needed

Pliers Flat-blade

Screwdriver

Level

Installation Overview

Please read the following installation instructions rst after purchasing this product or transporting it to another

location.

Choosing the proper location

Unpacking and removing shipping

material

Connecting the water lines

Connecting the drain hose

Leveling the washer

Connecting to the power supply

Testing the washer

TEST!

9INSTALLATION

ENGLISH

INSTALLATION

Tools Needed

Pliers Flat-blade

Screwdriver

Level

Installation Overview

Please read the following installation instructions rst after purchasing this product or transporting it to another

location.

Choosing the proper location

Unpacking and removing shipping

material

Connecting the water lines

Connecting the drain hose

Leveling the washer

Connecting to the power supply

Testing the washer

TEST!

Product Specications

The appearance and specications listed in this manual may vary due to constant product improvements.

Electrical requirements 120 VAC @ 60 Hz

Min. / Max. water pressure 20 - 120 psi (138 - 827 kPa)

Dimensions

27" (W) X 28

3

/8" (D) X 44

1

/2" (H), 57

1

/4" (H with lid (door) open)

68.6 cm (W) X 72.1 cm (D) X 113 cm (H), 145.3 cm (H with lid (door) open)

Net weight 134.5 lbs. (61 kg)

Max spin speed 950 RPM (±50 rpm)

WARNING

• Moving or installation of the appliance requires two or more people. Failure to follow these instructions may

result in injury.

• Store and install the appliance where it will not be exposed to temperatures below freezing or exposed to

outdoor weather conditions. Failure to follow this warning can cause product or part failure, serious injury,

re, electric shock, or death.

• Properly ground the washer to conform with all governing codes and ordinances. Failure to follow this

warning can cause serious injury, re, electric shock, or death.

• To reduce the risk of electric shock, do not install the appliance in humid spaces. Failure to follow this

warning can cause serious injury, re, electric shock, or death.

• To ensure proper airow, do not block the large opening on the bottom of the washer with carpeting or other

materials.

• Do not remove the ground prong. Do not use an adapter or extension cord. Plug into a grounded 3-prong

outlet. Failure to follow this warning can cause serious injury, re, electric shock, or death.

• Certain internal parts are intentionally not grounded and may present a risk of electric shock only during

servicing. Service personnel-do not contact the following parts while the appliance is energized. : pump,

motor, noise lter cover, and heater (on applicable models).

10 INSTALLATION

Choosing the Proper

Location

Install the washer on a solid oor that is strong and

rigid enough to support the weight of the washer,

even when fully loaded, without exing or bouncing.

If the oor has too much ex, you may need to

reinforce it to make it more rigid. If the oor is not

solid, it may cause severe vibration and noise.

NOTE

• Before installing the washer, make sure the oor

is clean, dry and free of dust, dirt, water and oil so

the washer feet cannot slide easily. Leveling feet

that can move or slide on the oor can contribute to

excess vibration and noise due to poor contact with

the oor.

• Allow for sufcient space between the walls and the

washer for installation.

Power Outlet

• The power outlet must be within 60 inches (1.5 m)

of either side of the washer.

• The appliance and outlet must be positioned so that

the plug is easily accessible.

• Do not overload the outlet with more than one

appliance.

• The outlet must be grounded in accordance with

current electrical wiring codes and regulations.

• Use a time-delay fuse or circuit breaker.

NOTE

• It is the personal responsibility and obligation of the

product owner to have a proper outlet installed by a

qualied electrician.

Flooring

• To minimize noise and vibration, the washer must

be installed on a solidly constructed oor.

• Allowable slope under the entire washer is a

maximum 1 inch difference from side to side or from

front to back.

• Installing on carpeting and soft tile surfaces is not

recommended.

• Never install the washer on a platform or weakly

supported structure.

NOTE

• The washer must be installed on rm ooring to

minimize vibration during the spin cycle. Concrete

ooring is best, but a wood oor is sufcient,

provided it is built to FHA standards.

Floor Installation

44 ¼"

(113 cm)

27"

(68.6 cm)

1"

(2.5 cm)

1"

(2.5 cm)

To ensure sufcient clearance for water lines, the

drain line and airow, allow minimum clearances of

at least 1 inch (2.5 cm) at the sides and 4 inches (10

cm) behind the unit. Be sure to allow for wall, door,

or oor moldings that may increase the required

clearances.

57 ¼"

(145.3 cm)

26 ¾"

(68 cm)

28 ⅜"

(72.1 cm)

32"

(81.1 cm)

3 ½"

(9 cm)

• Minimum vertical space from oor to overhead

shelves, cabinets, ceilings, etc., is 58 inches (147

cm).

11INSTALLATION

ENGLISH

Unpacking and Removing

Shipping Material

Unpack all shipping materials from the washer for

proper operation and inspect it for shipping damage.

CAUTION

• Failure to remove shipping materials can cause

excessive noise and vibration.

1

Lift the washer off the foam base.

After removing the carton and shipping material,

lift the washer off the foam base. Make sure the

plastic tub support comes off with the base and is

not stuck to the bottom of the washer.

If you must lay the washer down to remove the

base packaging materials, always protect the side

of the washer and lay it carefully on its side. Do

not lay the washer on its front or back.

Plastic tub support

Carton base

2

To prevent damage, do not remove the foam

block containing the owner’s manual, parts, and

laundry product samples from the washer tub until

the washer is in the nal location.

NOTE

• Once removed, save the foam block for future use.

If the washer needs to be moved, the foam block

will help prevent damage during transportation.

3

Unfasten the power cord from the back of the

washer.

12 INSTALLATION

Connecting the Water Lines

To avoid the risk of costly water damage, purchase

and install new inlet hoses when installing the

washer.

1

Check the ttings and seals.

Inspect the threaded tting on each hose and

make sure there is a rubber seal in place in both

ends of each hose to prevent leaking.

Rubber seal Rubber seal

Water hose (to water

inlet on washer)

Water hose (to tap)

2

Connect the water supply hoses.

Connect the water supply hoses to the hot and

cold water faucets tightly by hand and then

tighten another 2/3 turn with pliers. Connect the

blue hose to a cold water faucet and the red hose

to a hot water faucet.

3

Flush out the inlet hoses.

After connecting the inlet hoses to the water

faucets, turn on the water faucets to ush out

foreign substances (dirt, sand or sawdust) in the

water lines. Let water drain into a bucket, and

check the water temperature to make sure you've

connected the hoses to the correct faucets.

4

Attach the water lines to the back of the

washer.

Attach the hot water line to the hot water inlet on

the back of the washer. Attach the cold water line

to the cold water inlet on the back of the washer.

Tighten the ttings securely. Turn ON both faucets

all the way and check for leaks at both ends of the

hoses.

Hot water inlet

Cold water inlet

WARNING

• Do not overtighten the hoses or cross-thread the

hose ttings. Overtightening or cross-threading

can damage the valves or couplings, resulting in

leaking and property damage.

• Do not reuse old hoses. Use only new hoses

when installing the washer. Old hoses could leak

or burst causing ooding and property damage.

Contact an LG Customer Information Center for

assistance in buying hoses.

NOTE

• Periodically check the hoses for cracks, leaks, and

wear, and replace the hoses every ve years. Do

not stretch the water hoses intentionally, and make

sure that they are not pinched, crushed or kinked by

other objects.

• Water supply pressure must be between 20 psi

and 120 psi (138 – 827 kPa). If the water supply

pressure is more than 120 psi, a pressure reducing

valve must be installed.

• To provide optimum washing performance, the hot

water temperature should be set at 120 – 135 °F

(48 – 57 °C) and the cold at 60 °F (15 °C).

• The washer should never be installed or stored in a

location subject to freezing temperatures. Damage

to the water lines and internal mechanisms of the

washer can result. If the washer was exposed to

freezing temperatures prior to installation, allow it to

stand at room temperature for several hours before

use and check for leaks prior to operation.

• Do not use ood-preventing hoses with auto shutoff

devices. The devices can be tripped during ll and

prevent the machine from lling properly.

13INSTALLATION

ENGLISH

Connecting the Drain Hose

Connect the drain hose to either a standpipe or

laundry tub.

NOTE

• The drain hose should always be properly secured.

Failure to properly secure the drain hose can result

in ooding and property damage.

• The drain must be installed in accordance with any

applicable local codes and regulations.

• Make sure that the drain hose is not stretched,

pinched, crushed, or kinked.

• Do not install the drain hose with the end lower than

29.5 inches (75 cm) or higher than 96 inches (244

cm) above the bottom of the washer or more than

60 inches (152 cm) away from the washer.

• Never create an airtight seal between the hose and

the drain with tape or other means. If no air gap

is present, water can be siphoned out of the tub

resulting in poor wash/rinse performance or clothing

damage.

• Normal height of the end of the hose should be

approximately 35 inches (89 cm) to 47 inches (120

cm) from the oor.

Option 1: Standpipe

1

Insert the end of the drain hose into the

standpipe.

2

Use the provided tie strap to secure the drain

hose in place.

3

If the water valves and drain are built into the wall,

fasten the drain hose to one of the water hoses

with the tie strap provided (ribbed side on inside).

29.5 - 96 "

(75 - 244 cm)

29.5 - 96 "

(75 - 244 cm)

Tie strap

CAUTION

• Do not insert the end of the drain hose into the

standpipe more than 8 inches (20 cm). Doing

so can cause siphoning, odors, or improper

draining.

NOTE

• If the drain is large enough for the ange on the

hose to t inside, then do not insert the ange more

than 1-2 inches into the drain.

Option 2: Laundry Tub

1

Hang the end of the drain hose over the side of

the laundry tub.

2

Use the provided tie strap to secure the drain

hose in place.

14 INSTALLATION

Leveling the Washer

The tub of the washer spins at very high speeds. To

minimize vibration, noise, and unwanted movement,

the oor must be a level, solid surface.

NOTE

• Adjust the leveling feet only as far as necessary to

level the washer. Extending the leveling feet more

than necessary can cause the washer to vibrate.

• Before installing the washer, make sure that the

oor is clean, dry and free of dust, dirt, water and

oil so the washer feet cannot slide easily. Feet

that move or slide on the oor can contribute to

excessive vibration and noise due to poor contact

with the oor.

1

Position the washer in its nal location.

Take special care not to pinch, strain, or crush the

water and drain lines. If you have a carpenter’s

level, you can use it to check that the washer

level. The slope beneath the washer should not

exceed 1 inch, and all four leveling feet must rest

rmly on the oor.

1"

Level

2

Open the lid (door) and look from above to see

if the tub is centered.

If the tub is NOT centered, readjust the front feet.

If you have a level, check the washer with the

level.

NOTE

• To check if the washer is level from side to side,

place a level on the back edge of the lid (door).

• To check if the washer is level from front to back,

place a level at the side of the washer on the

edge where the cabinet side meets the top cover.

Do not place the level on the top of the lid (door).

Using these surfaces will result in the washer being

unlevel.

Level from side to side

Level from

front to back

3

Adjust the lower leveling feet.

Turn in one direction to raise the washer or the

other direction to lower it.

Raise Lower

4

Recheck the washer’s levelness.

Push or rock the top edges of the washer gently

to make sure the washer does not rock. If the

washer rocks, repeat steps 1-3.

CAUTION

• Using the washer without leveling it may cause

excess vibration and noise, leading to a machine

malfunction.

• Extend the leveling feet only to level the washer.

If you extend the leveling feet unnecessarily, it

may cause abnormal vibration of the washer.

NOTE

• If the washer is not level, the lid (door) may not

stay open properly. If this happens, extend the front

leveling legs until the washer is level from front to

back.

15INSTALLATION

ENGLISH

Connecting to the Power

Supply

The washer should be plugged into a 120-VAC, 60

Hz grounded 3-prong outlet. Plug in the washer.

WARNING

• Do not use a worn or damaged power cord or

power plug. Replace or repair it immediately.

Failure to do so may result in death, re, electric

shock, or malfunction.

• Do not modify the power cord and plug

provided with the appliance. Do not damage

it when installing or moving the washer. Doing

so may result in death, re, electric shock, or

malfunction.

• Make sure that the washer is grounded.

• Connect this washer to a grounded outlet

conforming to the rating prior to use. Failure

to do so may result in re, electric shock, or

malfunction.

• Do not damage or cut off the ground prong of

the power cord. Doing so may cause death, re,

electric shock, or product malfunction.

• Improper connection of the equipment-grounding

conductor can result in risk of electric shock.

Check with a qualied electrician or service

technician if you are in doubt as to whether the

appliance is properly grounded. If it does not t

the outlet, have a proper outlet installed by a

qualied electrician.

• The appliance and outlet must be positioned so

that the plug is easily accessible.

• Do not use adapters or extension cords. Doing

so may result in serious injury, re, electric

shock, or death.

• For best performance, plug the washer into

its own individual outlet. This helps prevent

overloading house wiring circuits which could

cause a re hazard from overheated wires.

• If necessary, use a new, UL-listed 3-prong

adapter or 3-wire extension cord with a 3-prong

(grounding) plug rated at no less than the branch

circuit. Do not use an extension cord longer

than 3 feet. Failure to follow these warnings may

result in serious injury, re, electric shock, or

death.

Testing the Washer

Check if the washer is properly installed and run a

test cycle.

1

Make sure the tub is empty. Do not load anything

in the tub for this test.

2

Press the Power button.

3

Press and hold the Spin and Soil buttons

simultaneously until an

appears in the

display.

Display Information

Initial test

Previous test result was good.

Previous test was ended with an

error.

NOTE

•

is displayed rst, and , or is displayed.

• The indication is different for each model.

4

Press the Start/Pause button.

The washer will start the test, which will last about

3 minutes. The test automatically checks the

water inlet hoses and the drain hose.

5

Check the display for results.

If error code is displayed, refer to the following

guide.

Error Code Solution

Fully open the water faucets.

Straighten out any kinks in the inlet

hoses and make sure the hoses are

not pinned against the wall or under

the washer.

Straighten out any kinks in the drain

hose and make sure the hose is not

pinned against the wall or under the

washer. Remove and ush out the

drain hose to remove clogs. Adjust

or repair the drain. Maximum drain

height is 96 inches.

6

End of cycle.

At the end of the test cycle,

or will

display. The test cycle will end and the washer will

shut off automatically after a short delay.

16 OPERATION

OPERATION

Using the Washer

WARNING

• To reduce the risk of re, electric shock, or injury

to persons, read the SAFETY INSTRUCTIONS

before operating this appliance.

1

Sort laundry and load the washer.

Sort laundry by fabric type, soil level, color and

load size, as needed. Open the lid (door) and load

items into the washer.

2

Add cleaning products.

Add the proper amount of HE (High-Efciency)

detergent to the detergent dispenser. If desired,

add bleach or fabric softener to the appropriate

dispensers.

3

Turn on the washer.

Press the Power button to turn on the washer.

The lights above the cycle buttons will illuminate

and a chime will sound.

4

Select a cycle.

Turn the cycle selector knob or press the cycle

buttons repeatedly until the desired cycle is

selected. The preset wash temperature, spin

speed, soil level and option settings for that cycle

are shown.

• Pressing the Start/Pause button without

selecting a cycle will cause the Normal cycle to

begin immediately.

5

Adjust settings.

Default settings for the selected cycle can now be

changed, if desired, using the cycle modier and

option buttons.

NOTE

• Not all modiers and options are available on all

cycles. A different chime sounds and the LED does

not light up if the selection is not allowed.

6

Begin cycle.

Press the Start/Pause button to begin the cycle.

The lid (door) locks, and the washer agitates

briey without water to measure the weight of the

load.

7

Additional garments can be added to the tub

while the Add Garment light is on.

The Add Garment light illuminates near the

beginning of the wash cycle to indicate when

it is safe to add items to the load. Press the

Start/Pause button to pause the cycle and add

garments to the load. Press the Start/Pause

button to resume the cycle.

NOTE

• Adding items after the Add Garment light turns off

may result in poor wash performance.

8

End of cycle.

When the cycle is nished, a melody sounds.

Immediately remove the clothing from the washer

to reduce wrinkling.

• If the washer includes lint lters, remember to

check them after every 2 to 3 loads.

17OPERATION

ENGLISH

Sorting Laundry

CAUTION

• The washer can be fully loaded, but the tub

should not be tightly packed with items. The lid

(door) of the washer should close easily.

• Use the Bedding cycle for buoyant or

nonabsorbent items such as pillows or

comforters. Failure to follow this caution can

result in leakage.

• Clothing or articles that are waterproof or water

resistant must be washed in the Waterproof

cycle only. (e.g. water resistant clothing, mattress

covers, outdoor clothes, plastic mats, etc.)

Otherwise, it may result in personal injury or

damage to the washer, clothes, walls, oor, and

surrounding objects due to abnormal vibration.

Grouping Similar Items

For the best washing results, and to reduce the

possibility of damage to clothing, care should be

taken to sort the clothing into loads that are made up

of similar items.

Mixing different fabric types and/or soil levels can

result in poor wash performance, color transfer,

discoloration, fabric damage or linting. Fabrics should

be sorted into groups as described below.

Colors

Sort articles by color. Wash dark clothes together in a

separate load from light colors or whites. Mixing dark

clothes with light clothes can result in dye transfer or

discoloration of the lighter clothes.

Soil Level

Wash heavily soiled clothing together. Washing lightly

soiled clothing in the same load with heavily soiled

clothing could result in poor wash performance for

the lightly soiled clothing.

Fabric Type

Delicate articles should not be mixed with heavy

or sturdy fabric types. Washing heavy fabrics in a

delicate load can result in poor wash performance

for the heavy fabrics and possible damage to the

delicates.

Lint Type

Some fabrics attract and bind lint to them while others

give off lint in the laundry process. Avoid mixing these

lint collectors and lint producers in the same load.

Mixing these fabrics will result in pilling and linting on

the lint collectors. (For example, lint collector—knit

sweater; lint producer—terry cloth towels.)

Sort Laundry

By Colors By Soil By Fabric By Lint

White Heavy Delicates

Lint

Producer

Lights Normal Easy Care

Lint

Collector

Darks Light Sturdy

Fabric Care Labels

Many articles of clothing include a fabric care label.

Using the chart below, adjust the cycle and option

selections to care for your clothing according to the

manufacturer’s recommendations.

Category Label Directions

Washing

Hand wash

Machine wash, Normal cycle

Perm Press/Wrinkle

Resistant setting (which has

a cool down or cold spray

before the slower spin)

Gentle/Delicate setting (slow

agitation and/or reduced

wash time)

Do not wash

Do not wring

Water

Temperature

Hot

Warm

Cold/Cool

Bleach

Symbols

Any bleach (when needed)

Only non-chlorine bleach

(when needed)

Do not bleach

18 OPERATION

Loading the Washer

• Check and empty pockets. Paper clips, coins,

matches, etc. can damage clothing and the washer.

• Close zippers and hooks, and tie drawstrings to

prevent snagging or tangling of clothes.

• Pretreat heavily stained areas for best results.

• Combine large and small items in a load. Load large

items rst. Large items should not be more than half

of total load.

• Wash thick, bulky items individually. Heavy blankets,

comforters, bedspreads, or pet beds can get

tangled or cause an unbalanced load if combined

with other items.

• The washer can be fully loaded, but the tub should

not be tightly packed with items. The lid (door) of

the washer must close easily.

• Do not wash single small items. Add 1-2 similar

items to the load to prevent an out-of-balance load.

• Do not wash/spin waterproof items. Washing

raincoats or sleeping bags may result in abnormal

vibration or may cause the load to bounce, which

could damage the tub.

• Wash small, light items in a mesh bag. Small items

can get caught in the impeller at the bottom of the

tub, and brassiere hooks can damage other items

or the tub.

• Brush off heavy soil, dust, and hair from items

before washing. Excess dirt or sand can abrade

other fabrics and lead to poor wash performance.

• The washer will not ll or operate with the lid (door)

open.

• Use the Bedding cycle for large or bulky items such

as poly-lled jackets, comforters, pillows, etc. These

items may not be as absorbent as other laundry

items and should be sorted into a separate wash

load for optimal results.

• Bulky items should be placed as far down in the

tub as possible for optimal results. Always place

buoyant items at the bottom of the tub. The washer

will automatically detect the load size. Because of

the high efciency wash system, the water level

may not completely cover the load.

• Do not overload the tub. Clothes should t loosely in

the tub under the maximum ll line. Loading clothes

over the ll line may result in damage to clothing

and the washer.

- Load clothes loosely, and do not overll the tub.

Clothes need room to circulate in order to get

clean.

- Do not press down on items while stacking them

in the tub.

Maximum ll line

• For best performance, load clothes as shown.

19OPERATION

ENGLISH

Adding Cleaning Products

About the Dispensers

The automatic dispenser consists of two

compartments which hold:

• Liquid fabric softener

• Liquid or powdered detergent for main wash

Using the Detergent and Softener

Dispensers

To add detergent and fabric softener to the automatic

dispenser:

1

Open the dispenser drawer.

2

Load the laundry products into the

appropriate compartments.

Liquid fabric softener

compartment

Main wash liquid

detergent compartment

Insert

Main wash powder

detergent compartment

3

Close the drawer completely before starting

the cycle.

• Be careful not to catch a hand in the drawer

while closing.

CAUTION

• Do not place or store laundry products, such

as detergent, bleach, or liquid fabric softener,

on top of your appliance. Wipe up any spills

immediately. These products can damage the

appliance’s nish and controls.

NOTE

• It is normal for a small amount of water to remain in

the dispenser compartments at the end of the cycle.

Main Wash Detergent Compartment

This compartment holds laundry detergent for the

main wash cycle. Either powdered or liquid detergent

may be used in this compartment. The detergent

is added to the load at the beginning of the cycle.

Always use HE (High-Efciency) detergent with your

washer.

NOTE

• Never exceed the manufacturer’s recommendations

when adding detergent. Using too much detergent

can result in detergent buildup in clothing and the

washer.

• When using liquid detergent, make sure the liquid

detergent compartment and insert are in place. Do

not exceed the maximum ll line.

• When using powdered detergent, remove the

insert and liquid detergent compartment from the

dispenser. Powdered detergent will not dispense

with the liquid detergent compartment and insert in

place.

• If you use a detergent that does not dissolve easily

or a detergent with high viscosity, it will leave a

residue and clog the dispenser.

Fabric Softener Compartment

This compartment holds liquid fabric softener, which

is automatically dispensed during the nal rinse cycle.

NOTE

• Do not exceed the manufacturer’s

recommendations when adding softener. Using too

much fabric softener can result in buildup in clothing

and the washer. Either powdered or liquid fabric

softener may be used.

• Follow the manufacturer’s recommendations when

adding fabric softener. Do not exceed the maximum

ll line. Using too much fabric softener may stain

clothes.

• Dilute concentrated fabric softeners with warm

water.

• Never pour fabric softener directly onto the load or

into the tub.

20 OPERATION

Using the Liquid Bleach Dispenser

The bleach dispenser is a separate compartment at

the left front of the tub opening.

Type 1

The bleach dispenser is connected to the inlet valve.

The bleach is automatically diluted and dispensed at

the proper time in the wash cycle.

NOTE

• The dispenser is activated twice to ensure complete

dispensing of the bleach. Any liquid remaining in

the dispenser at the end of the cycle is water, not

bleach.

Type 2

When you pour the bleach into the bleach dispenser,

the bleach is immediately added to the tub as it lls

with water, safely diluting the bleach.

NOTE

• The dispenser cover cannot be removed. To clean

the cover, wipe it with a damp paper towel.

1

Check clothing care labels for special instructions.

2

Measure liquid bleach carefully, following

instructions on the bottle.

• High-efciency washers use less water, so less

bleach is needed. One half cup is enough for

most loads.

3

Carefully pour the pre-measured amount of

bleach directly into the bleach dispenser.

• If you are using powdered bleach of any kind,

pour it directly into the tub before adding the

laundry. Never add powdered bleach to the

liquid bleach dispenser.

WARNING

• Do NOT mix chlorine bleach with ammonia or

acids such as vinegar or rust/scale remover.

Mixing chemicals like these can produce a lethal

gas, resulting in severe injury or death.

NOTE

• Do not add powdered bleach to this dispenser. The

bleach dispenser is designed to dispense liquid

bleach only. Powdered or liquid color-safe bleach

will not dispense properly.

• Do not place laundry items on top of the bleach

dispenser when loading and unloading the washer.

• Always follow the manufacturer’s recommendations

when adding bleach. Never add more than one cup

and do not exceed the maximum ll line since this

can cause the bleach to be dispensed immediately,

resulting in damage to fabrics. Using too much

bleach can damage fabrics.

• Never pour undiluted liquid chlorine bleach directly

onto the load or into the tub. Fabric damage can

occur.

• Do not use color-safe bleach or Oxi products in the

same cycle with liquid chlorine bleach.

La page charge ...

LG Washing Machine [WT7100C] Manuel utilisateur

LG Washing Machine [WT7100C] Manuel utilisateur

dans d''autres langues