Show Home ZW96 Manuel utilisateur

Taper
Manuel utilisateur
Federal Communications Commission (FCC) Statement
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may caus harmful interference to radio communications.However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.Increase the separation between the equipment and
receiver.Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.Consult the dealer or an experienced radio/TV technician for help.This equipment
should be installed and operated with minimum distance 20cm between the radiator and your body.
IC Caution:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject
to the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired
operation of the device.
DECLARATION DE CONFORMITE D'INDUSTRIE CANADA
Ce périphérique a été testé et reconnu conforme aux limites spécifiées dans RSS-210.
Son utilisation est soumise aux deux conditions suivantes :
(1) il ne doit pas provoquer d'interférences gênantes et
(2) il doit tolérer les interférences re.ues, notamment cellessusceptibles d'en perturber le fonctionnement.
ZW96 Smart Plug(1 Channel) Manual
smart plug
(2) il doit tolérer les interférences re.ues, notamment cellessusceptibles d'en perturber le fonctionnement.
WARRANTY
Show Home Products warrants this product to be free from manufacturing defects for
a period of two years from the original date of consumer purchase. This warranty is limited
to the repair or replacement of this product only and does not extend to consequential or
incidental damage to other products that may be used with this product.
allow limitations on how long an implied warranty lasts or permit the exclusion or limitation
of incidental or consequential damage, so the above limitations may not apply to you.
This warranty gives you specific rights, and you may also have other rights which vary from
state to state. if the unit should prove defective within the warranty period.
SPECIFICATIONS WARNING
Model:ZW96
RISK OF FIRE
Power: 120 VAC, 60 Hz.
RISK OF ELECTRICAL SHOCK
Signal (Frequency): 908.42 MHZ.
RISK OF BURNS
Maximum load for outlet 15A, 1200W Resistive
CONTROLLING APPLIANCES:
Maximum load for the Z-Wave controlled outlet:
EXERCISE EXTREME CAUTION WHEN USING Z-WAVE DEVICES TO CONTROL
600W Incandescent, ½ HP Motor or 1200W Resistive
APPLIANCES. OPERATION OF THE Z-WAVE DEVICE MAY BE IN A DIFFERENT
Range: Up to 100 feet line of sight between the Wireless Controller
ROOM THAN THE CONTROLLED APPLIANCE, ALSO ANUNINTENTIONAL ACTIVATION
and the closest Z-Wave receiver module.
MAY OCCUR IF THE WRONG BUTTON ON THE REMOTE IS PRESSED. Z-WAVE DEVICES
Operating Temperature Range: 32-104° F (0-40° C)
MAY AUTOMATICALLY BE POWERED ON DUE TO TIMED EVENT PROGRAMMING.
For indoor use only.
DEPENDING UPON THE APPLIANCE, THESE UNATTENDED OR UNINTENTIONAL
Specifications subject to change without notice
OPERATIONS COULD POSSIBLY RESULT IN A HAZARDOUS CONDITION. FOR THESE
due to continuing product improvement
REASONS, WE RECOMMEND DO NOT RETURN THIS PRODUCT TO THE STORE
THE FOLLOWING:
Website:www.ishowlights.com
DO NOT USE Z-WAVE DEVICES TO CONTROL ELECTRIC
HEATERS OR ANY OTHER APPLIANCES WHICH MAY PRESENT
A HAZARDOUS CONDITION DUE TO UNATTENDED OR
UNINTENTIONAL OR AUTOMATIC POWER ON CONTROL.
Getting To Know Your New Z-Wave Device
Must not exceed 600 watts (Incandescent): 1200W (10A) Resistive or ½ HP
Motor. Total load capacity for both outlets is 1200W (10A) Resistive.
One Z-Wave controlled AC outlet for standard incandescent lighting, CFL/LED, fans or small appliances
Remote ON/OFF control via the Z-Wave controller
Manual ON/OFF control with the front panel push button
Space efficient design
Does not block the lower outlet when plugged into the upper outlet of a duplex wall receptacle
(This assumes that the duplex receptacle is mounted with the ground pin down).
Plugs and cords for connected devices route to the side allowing close placement of furniture
Grounded 3-wire power connection for safety
A.AC IN
B. Manual/Program button
Single press — turn the lamp On/Off
Single press — include or exclude in Z-Wave network
C.Always-on outlet
D. Z-Wave controlled outlet
This outlet can remotely turn On/Off the connected device
1. Plug the light you want to control into the Z-Wave Smart plug controlled outlet
on the wireless switch as indicated by Z-Wave logo
NOTE
: Plug directly into outlet, do not use with extension cords
2. Plug the Z-Wave smart plug directly into an available
grounded outlet (Top outlet recommend if possible).
Reset Plug to factory default:
A
D
C
B
Reset Plug to factory default:
Use controller to remove device from network will reset it to factory default
Adding device to e network:
1. Follow the instructions for your Z-Wave certified controller to include a device to
the Z-Wave network.
2. Once the controller is ready to include your device, quick triple press the button to
include it in the network.
3. Once your controller has confirmed that the device has been included, refresh
the Z-Wave network to optimize performance.
4. The device is associated in the same group when it included in setting process.
Now you can control your Z-Wave device according to groups, scenes, schedules
and automation programmed. If your controller features remote access,
you can now control all devices in Z-Wave network from mobile devices.
To exclude the device
1. Follow the instructions for your Z-Wave certified controller to exclude a device
from the Z-Wave network.
2. Once the controller is ready to Exclude your device, quick triple press the button
to exclude it from the network.
I. The association group supports five nodes and lifeline function.
II.All non-battery nodes within Z-Wave network will act as repeater.
III.Use this procedure only in the event that the network primary controller is
missing or otherwise inoperable.
Note
: Your device may need to be within 10 feet of the controller to be included. If so, include the device to the network within 10 feet
of the controller and relocate it to the desired position in your home. Besure to refresh the network if the device is included in this manner.
Please reference the controller/gateway’s manual for instructions.
Now you have complete control to turn your lamp ON/OFF according to groups, scenes, schedules and interactive automations programmed
by your controller.If your Z-Wave certified controller features Remote Access,you can now control your lighting from your mobile phone devices.
  • Page 1 1
  • Page 2 2

Show Home ZW96 Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues