DeWalt DCHT820P1WR320B Manuel utilisateur

Marque: DeWalt

Modèle: DCHT820P1WR320B

Catégorie: Taille-haies électriques

Taper: Manuel utilisateur

DCHT820 20V Max* Lithium Hedge Trimmer

Taille-haie au lithium-ion de 20 V max.* DCHT820

Cortasetos con batería de iones de litio de 20 V Máx* DCHT820

INSTRUCTION MANUAL

GUIDE D'UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE

GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE

USAR EL PRODUCTO.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-DeWALT • www.dewalt.com

English

Denitions: Safety Guidelines

The definitions below describe the level of severity for each signal

word. Please read the manual and pay attention to these symbols.

DANGER: Indicates an imminently hazardous situation

which, if not avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which,

if not avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if

not avoided, may result in minor or moderate injury.

NOTICE: Indicates a practice not related to personal injury

which, if not avoided, may result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR

ANY D

eWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DeWALT

(1-800-433-9258).

WARNING: To reduce the risk of injury, read the instruction manual.

General Power Tool Safety Warnings

WARNING! Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in

electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your mains-operated

(corded) power tool or battery-operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or dark areas

invite accidents.

b) Do not operate power tools in explosive atmospheres, such

as in the presence of flammable liquids, gases or dust.

Power tools create sparks which may ignite the dust or fumes.

c) Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs with

earthed (grounded) power tools. Unmodified plugs and

matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces such

as pipes, radiators, ranges and refrigerators. There is an

increased risk of electric shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet conditions. Water

entering a power tool will increase the risk of electric shock.

d) Do not abuse the cord. Never use the cord for carrying,

pulling or unplugging the power tool. Keep cord away

from heat, oil, sharp edges or moving parts. Damaged or

entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension

cord suitable for outdoor use. Use of a cord suitable for

outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location is unavoidable,

use a ground fault circuit interrupter (GFCI) protected

supply. Use of a GFCI reduces the risk of electric shock.

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a

power tool while you are tired or under the influence of

drugs, alcohol or medication. A moment of inattention while

operating power tools may result in serious personal injury.

English

tools. Such preventive safety measures reduce the risk of

starting the power tool accidentally.

d) Store idle power tools out of the reach of children and do

not allow persons unfamiliar with the power tool or these

instructions to operate the power tool. Power tools are

dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding

of moving parts, breakage of parts and any other condition

that may affect the power tool’s operation. If damaged,

have the power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to bind and

are easier to control.

g) Use the power tool, accessories and tool bits, etc. in

accordance with these instructions, taking into account

the working conditions and the work to be performed. Use

of the power tool for operations different from those intended

could result in a hazardous situation.

5) BATTERY TOOL USE AND CARE

a) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type of battery

pack may create a risk of fire when used with another battery

pack.

b) Use power tools only with specifically designated battery

packs. Use of any other battery packs may create a risk of

injury and fire.

c) When battery pack is not in use, keep it away from other

metal objects like paper clips, coins, keys, nails, screws,

or other small metal objects that can make a connection

from one terminal to another. Shorting the battery terminals

together may cause burns or a fire.

d) Under abusive conditions, liquid may be ejected from

the battery, avoid contact. If contact accidentally occurs,

b) Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask, non-

skid safety shoes, hard hat, or hearing protection used for

appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in

the off position before connecting to power source and/

or battery pack, picking up or carrying the tool. Carrying

power tools with your finger on the switch or energizing power

tools that have the switch on invites accidents.

d) Remove any adjusting key or wrench before turning the

power tool on. A wrench or a key left attached to a rotating

part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at

all times. This enables better control of the power tool in

unexpected situations.

f) Dress properly. Do not wear loose clothing or jewelry.

Keep your hair, clothing and gloves away from moving

parts. Loose clothes, jewelry or long hair can be caught in

moving parts.

g) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection can

reduce dust-related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the correct power tool

for your application. The correct power tool will do the job

better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it

on and off. Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the

battery pack from the power tool before making any

adjustments, changing accessories, or storing power

English

CAUTION: Do not expose to rain.

WARNING:Remove plug from the outlet

immediately if the extension cord becomes damaged or cut.

WARNING: Some dust created by this product

contains chemicals known to the State of California to cause cancer,

birth defects or other reproductive harm. Some examples of these

chemicals are:

• compounds in fertilizers

• compounds in insecticides, herbicides and pesticides

• arsenic and chromium from chemically treated lumber

To reduce your exposure to these chemicals, wear approved safety

equipment such as dust masks that are specially designed to filter out

microscopic particles.

• The label on your tool may include the following symbols. The

symbols and their definitions are as follows:

V ...................volts

A ...................amperes

Hz ................. hertz

W ..................watts

min ............... minutes

or AC ....... alternating

current

or DC ... direct current

................. Class I

Construction

(grounded)

o ................. no load speed

................. Class

II Construction

(double

insulated)

…/min .......... per minute

RPM ............. revolutions per

minute

................. earthing terminal

.................. safety alert

symbol

CSPM ........... cut strokes per

minute

flush with water. If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery may cause

irritation or burns.

6) SERVICE

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

Hedge Trimmer Safety Warnings

• Keep all parts of the body away from the cutter blade.

Do not remove cut material or hold material to be cut

when blades are moving. Make sure the switch is off when

clearing jammed material. Blades coast after turn off. A

moment of inattention while operating the hedge trimmer may

result in serious personal injury.

• Carry the hedge trimmer by the handle with the cutter

blade stopped. Proper handling of the hedge trimmer will reduce

possible personal injury from the cutter blades.

DANGER: Keep hands away from blade. Contact

with blade will result in serious personal injury.

• Hold the power tool by insulated gripping surfaces only,

because the cutter blade may contact hidden wiring. Cutter

blades contacting a “live” wire may make exposed metal parts of

the power tool “live” and could give the operator an electric shock.

• Use both hands when operating the hedge trimmer. Using

one hand could cause loss of control and result in serious

personal injury.

• Keep extension cord away from cutting area. During

operation the extension cord may be hidden in shrubs and can

be accidentally cut by the blade.

• Check the hedge for foreign objects, e.g. wire fences.

English

damaged, do not insert into the charger. Do not crush, drop or damage

the battery pack. Do not use a battery pack or charger that has

received a sharp blow, been dropped, run over or damaged in any way

(e.g., pierced with a nail, hit with a hammer, stepped on). Damaged

battery packs should be returned to the service center for recycling.

WARNING: Fire hazard. Do not store or carry

the battery pack so that metal objects can contact exposed

battery terminals. For example, do not place the battery pack in

aprons, pockets, tool boxes, product kit boxes, drawers, etc., with

loose nails, screws, keys, etc. Transporting batteries can possibly

cause fires if the battery terminals inadvertently come in

contact with conductive materials such as keys, coins, hand

tools and the like. The US Department of Transportation Hazardous

Material Regulations (HMR) actually prohibit transporting batteries in

commerce or on airplanes (e.g., packed in suitcases and carry-on

luggage) UNLESS they are properly protected from short circuits. So

when transporting individual battery packs, make sure that the battery

terminals are protected and well insulated from materials that could

contact them and cause a short circuit.

Transportation

Your DeWALT batteries comply with all applicable shipping

regulations as prescribed by industry and legal standards, including

UN Recommendations on the Transport of Dangerous Goods;

International Air Transport Association (IATA) Dangerous Goods

Regulations, International Maritime Dangerous Goods (IMDG)

Regulations, and U.S. Department of Transportation Regulations.

Lithium-ion cells and batteries have been tested to section 38.3 of the

UN Recommendations on the Transport of Dangerous Goods Manual

of Tests and Criteria.

The shipping or transportation of the battery in this product is restricted

and may be classified as a Class 9 Hazardous material.

Important Safety Instructions for All Battery

Packs

When ordering replacement battery packs, be sure to include the

catalog number and voltage. Consult the chart at the end of this

manual for compatibility of chargers and battery packs.

The battery pack is not fully charged out of the carton. Before using

the battery pack and charger, read the safety instructions below and

then follow charging procedures outlined.

READ ALL INSTRUCTIONS

• Do not charge or use the battery pack in explosive

atmospheres, such as in the presence of flammable liquids,

gases or dust. Inserting or removing the battery pack from the

charger may ignite the dust or fumes.

• NEVER force the battery pack into the charger. DO NOT

modify the battery pack in any way to fit into a non-

compatible charger as battery pack may rupture causing

serious personal injury. Consult the chart at the end of this

manual for compatibility of batteries and chargers.

• Charge the battery packs only in designated D

eWALT chargers.

• DO NOT splash or immerse in water or other liquids. If appliance

does get wet, allow to dry for a minimum of 48 hours before using.

• Do not store or use the tool and battery pack in locations

where the temperature may reach or exceed 105 °F (40 °C)

(such as outside sheds or metal buildings in summer). For

best life store battery packs in a cool, dry location.

NOTE: Do not store the battery packs in a tool with the

trigger switch locked on. Never tape the trigger switch in the

ON position.

WARNING: Fire hazard. Never attempt to open the

battery pack for any reason. If the battery pack case is cracked or

English

The information provided in this section of the manual is provided in

good faith and believed to be accurate at the time the document was

created. However, no warranty, expressed or implied, is given. The

shipper is responsible to comply with the applicable regulations.

SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION (Li-Ion)

• Do not incinerate the battery pack even if it is severely

damaged or is completely worn out. The battery pack can

explode in a fire. Toxic fumes and materials are created when

lithium ion battery packs are burned.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If battery

liquid gets into the eye, rinse water over the open eye for 15

minutes or until irritation ceases. If medical attention is needed,

the battery electrolyte is composed of a mixture of liquid organic

carbonates and lithium salts.

• Contents of opened battery cells may cause respiratory irritation.

Provide fresh air. If symptoms persist, seek medical attention.

WARNING: Burn hazard. Battery liquid may be

flammable if exposed to spark or flame.

The RBRC™ Seal

The RBRC® (Rechargeable Battery Recycling Corp-

oration) Seal on the lithium-ionbatteries (or battery

packs) indicates that the costs to recycle these batteries

(or battery packs) at the end of their useful life have

already been paid by BLACK+DECKER. In some areas,

it is illegal to place spent lithium-ion batteries in the trash or municipal

solid waste stream and the Call 2 Recycle® program provides an

environmentally conscious alternative.

Call 2 Recycle, Inc., in cooperation with BLACK+DECKER and other

battery users, has established the program in the United States and

Canada to facilitate the collection of spent lithium-ion batteries. Help

SHIPPING BY AIRPLANE (BY AIR) OR SHIP (BY SEA)

• Contact your carrier for up to date instructions. Have your contents

(including the battery) with you when contacting them. The

specifications written on them will be needed to prepare them for

shipment, pack them in a compliant box, and properly label the

box.

SHIPPING BY GROUND (HIGHWAY OR RAIL)

• The original product box and its packing material can be used for

shipping by ground within the United States and Canada with the

following stipulations:

1. The battery and all other contents must be in their original

packing materials and arranged as received (including the

battery in its original plastic bag and battery box).

2. The original product box and all other packing materials must

be undamaged.

3. The shipment must be include a document which contains the

following:

• The package contains lithium-ion cells or batteries.

• The package must be handled with care and that a

flammability hazard exists if the package is damaged.

• Special procedures should be followed in the event the

package is damaged, to include inspection and repacking if

necessary.

• The telephone numbers for additional information (US and

Canada 1-888-698-2571, Elsewhere +1-410-329-9200).

• To ship by ground in a generic box, contact your carrier for

up to date instructions. Have your contents (including the

battery) with you when contacting them. The specifications

written on them will be needed to prepare them for shipment,

pack them in a compliant box, and properly label the box.

It is forbidden to fly with these batteries even if the batteries are in

checked baggage.

English

• Do not expose the charger to rain or snow.

• Pull by the plug rather than the cord when disconnecting the

charger. This will reduce the risk of damage to the electric plug and cord.

• Make sure that the cord is located so that it will not be

stepped on, tripped over or otherwise subjected to damage

or stress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in risk of

fire, electric shock or electrocution.

• When operating a charger outdoors, always provide a dry

location and use an extension cord suitable for outdoor use. Use

of a cord suitable for outdoor use reduces the risk of electric shock.

• An extension cord must have adequate wire size (AWG or

American Wire Gauge) for safety. The smaller the gauge number

of the wire, the greater the capacity of the cable, that is, 16 gauge

has more capacity than 18 gauge. An undersized cord will cause a

drop in line voltage resulting in loss of power and overheating. When

using more than one extension to make up the total length, be sure

each individual extension contains at least the minimum wire size.

The following table shows the correct size to use depending on cord

length and nameplate ampere rating. If in doubt, use the next heavier

gauge. The lower the gauge number, the heavier the cord.

Minimum Gauge for Cord Sets

Ampere Rating

Volts Total Length of Cord in Feet (meters)

120V

25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)

240V

50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

Than

Not More

Than

AWG

0 6 18 16 16 14

6 10 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

protect our environment and conserve natural resources by returning

the spent lithium-ion batteries to an authorized BLACK+DECKER

service center or to your local retailer for recycling. You may also contact

your local recycling center for information on where to drop off the spent

battery. RBRC® is a registered trademark of Call 2 Recycle, Inc.

Important Safety Instructions for All Battery

Chargers

SAVE THESE INSTRUCTIONS: This manual contains important

safety and operating instructions for battery chargers.

• Before using the charger, read all instructions and cautionary markings

on the charger, battery pack and product using the battery pack.

WARNING: Shock hazard. Do not allow any liquid to

get inside the charger. Electric shock may result.

CAUTION: Burn hazard. To reduce the risk of injury,

charge only D

eWALT rechargeable battery packs. Other types of

batteries may overheat and burst resulting in personal injury and

property damage.

NOTICE: Under certain conditions, with the charger plugged into the

power supply, the charger can be shorted by foreign material. Foreign

materials of a conductive nature, such as, but not limited to, grinding

dust, metal chips, steel wool, aluminum foil or any buildup of metallic

particles should be kept away from the charger cavities. Always unplug

the charger from the power supply when there is no battery pack in the

cavity. Unplug the charger before attempting to clean.

• DO NOT attempt to charge the battery pack with any

chargers other than the ones in this manual. The charger and

battery pack are specifically designed to work together.

• These chargers are not intended for any uses other than

charging D

eWALT rechargeable batteries. Any other uses may

result in risk of fire, electric shock or electrocution.

English

blink continuously indicating that the charging process has

started.

3. The completion of charge will be indicated by the red light

remaining ON continuously. The pack is fully charged and may be

used at this time or left in the charger.

Indicator Light Operation

PACK CHARGING

PACK CHARGED

HOT/COLD DELAY

Charge Indicators

This charger has a hot/cold delay feature. When the charger detects

a battery that is hot, it automatically delays charging until the battery

has cooled. When the charger detects a battery that is cold, it

automatically delays charging until the battery has warmed.

The red light will continue to blink, but a yellow indicator light will

be illuminated during this operation. Once the battery has cooled,

the yellow light will turn off and the charger will resume the charging

procedure.

LEAVING THE BATTERY PACK IN THE CHARGER

The charger and battery pack can be left connected with the charge

indicator showing Pack Charged.

WEAK BATTERY PACKS: Weak batteries will continue to function

but should not be expected to perform as much work.

FAULTY BATTERY PACKS: This charger will not charge a faulty

battery pack. The charger will indicate faulty battery pack by refusing

to light.

• Do not place any object on top of the charger or place the

charger on a soft surface that might block the ventilation

slots and result in excessive internal heat. Place the charger

in a position away from any heat source. The charger is ventilated

through slots in the top and the bottom of the housing.

• Do not operate the charger with a damaged cord or plug.

• Do not operate the charger if it has received a sharp blow,

been dropped or otherwise damaged in any way. Take it to an

authorized service center.

• Do not disassemble the charger; take it to an authorized

service center when service or repair is required. Incorrect

reassembly may result in a risk of electric shock, electrocution or fire.

• Disconnect the charger from the outlet before attempting

any cleaning. This will reduce the risk of electric shock.

Removing the battery pack will not reduce this risk.

• NEVER attempt to connect 2 chargers together.

• The charger is designed to operate on standard 120V

household electrical power. Do not attempt to use it on any

other voltage.

Chargers

Be sure to read all safety instructions before using your charger.

Consult the chart at the end of this manual for compatibility of chargers

and battery packs.

Charging Procedure (Fig. 1)

1. Plug the charger into an appropriate

FIG. 1

outlet before inserting the battery

pack.

2. Insert the battery pack into the

charger, as shown in Figure 1, making

sure the pack is fully seated in the

charger. The red (charging) light will

English

c. Move the charger and battery pack to a location where the

surrounding air temperature is approximately 65 °F – 75 °F

(18° – 24 °C);

d. If charging problems persist, take the tool, battery pack and

charger to your local service center.

5. The battery pack should be recharged when it fails to produce

sufficient power on jobs which were easily done previously. DO

NOT CONTINUE to use it under these conditions. Follow the

charging procedure. You may also charge a partially used pack

whenever you desire with no adverse effect on the battery pack.

6. Foreign materials of a conductive nature such as, but not limited

to, grinding dust, metal chips, steel wool, aluminum foil, or any

buildup of metallic particles should be kept away from charger

cavities. Always unplug the charger from the power supply when

there is no battery pack in the cavity. Unplug the charger before

attempting to clean it.

7. Do not freeze or immerse the charger in water or any other liquid.

WARNING: Shock hazard. Don’t allow any liquid to get inside the

charger. Electric shock may result.

WARNING: Burn hazard. Do not submerge the battery pack in

any liquid or allow any liquid to enter the battery pack. Never attempt

to open the battery pack for any reason. If the plastic housing of the

battery pack breaks or cracks, return it to a service center for recycling.

Storage Recommendations

1. The best storage place is one that is cool and dry, away from direct

sunlight and excess heat or cold.

2. For long storage, it is recommended to store a fully charged

battery pack in a cool dry place out of the charger for optimal

results.

NOTE: Battery packs should not be stored completely depleted of

charge. The battery pack will need to be recharged before use.

NOTE: This could also mean a problem with a charger.

Wall Mounting

These chargers are designed to be wall mountable or to sit upright on

a table or work surface.

If wall mounting, locate the charger within reach of an electrical outlet.

Mount the charger securely using drywall screws at least 1” (25.4 mm)

long, screwed into wood to an optimal depth leaving approximately

7/32” (5.5 mm) of the screw exposed.

Important Charging Notes

1. Longest life and best performance can be obtained if the battery

pack is charged when the air temperature is between 65 °F and

75 °F (18° – 24 °C). DO NOT charge the battery pack in an air

temperature below +40 °F (+4.5 °C), or above +104 °F (+40 °C).

This is important and will prevent serious damage to the battery

pack.

2. The charger and battery pack may become warm to the touch

while charging. This is a normal condition, and does not indicate

a problem. To facilitate the cooling of the battery pack after use,

avoid placing the charger or battery pack in a warm environment

such as in a metal shed or an uninsulated trailer.

3. A cold battery pack will charge at about half the rate of a warm

battery pack. The battery pack will charge at that slower rate

throughout the entire charging cycle and will not return to

maximum charge rate even if the battery pack warms.

4. If the battery pack does not charge properly:

a. Check operation of the receptacle by plugging in a lamp or

other appliance;

b. Check to see if the receptacle is connected to a light switch

which turns the power off when you turn out the lights;

English

FIG. 3

FIG. 4

To remove battery pack: Depress thebattery release button (J) in

the back of the battery housing and pull battery pack out of tool as

shown in Figure 4.

FUEL GAUGE BATTERY PACKS (FIG. 5)

Some D

eWALT battery packs include a

FIG. 5

fuel gauge which consists of three

green LED lights that indicate the level

of charge remaining in the battery pack.

To actuate the fuel gauge, press and

hold the fuel gauge button (5A). A

combination of the three green LED

lights will illuminate designating the

level of charge left. When the level of

charge in the battery is below the usable limit, the fuel gauge will not

illuminate and the battery will need to be recharged.

NOTE: The fuel gauge is only an indication of the charge left on the battery

pack. It does not indicate tool functionality and is subject to variation

based on product components, temperature and end-user application.

For more information regarding fuel gauge battery packs, please call

1-800-4-D

eWALT (1-800-433-9258) or visit our website www.dewalt.com.

SAVE THESE INSTRUCTIONS

Components (Fig. 2)

A. Trigger switch F. Blade

B. Lock-off switch G Sheath

C. Switch handle H. Battery housing

D. Blade guard I. Battery pack

E. Bail handle J. Battery release button

FIG. 2

H I

OPERATION

Installing and Removing the Battery Pack

(Fig. 3–4)

WARNING: Before removing or installing battery,

make

certain the lock-off lever is engaged

to prevent switch actuation.

To install battery pack: Insert battery pack (I) into battery housing

(H) as shown in Figure 3 until fully seated and an audible click is heard.

Make sure battery pack is fully seated and fully latched into position.

English

FIG. 7

FIG. 8

LEVEL HEDGES (Fig. 9)

– To obtain exceptionally level hedges a

piece of string can be stretched along the length of the hedge as a

guide.

SIDE TRIMMING HEDGES (Fig. 10)

– Orient the trimmer as

shown and begin at the bottom and sweep up.

FIG. 9

FIG. 10

DANGER: KEEP HANDS AWAY FROM BLADES.

WARNING: To guard against injury, observe the

following:

Switch

To turn the unit on, push the lock off

FIG. 6

switch (B) forward as shown in Figure6,

and squeeze the trigger switch (A). Once

the unit is running, you may release the

lock off switch.

In order to keep the unit running you

must continue to squeeze the trigger. To

turn the unit off, fully release the trigger and allow the lock-off switch

(B) to engage.

WARNING: Never attempt to lock a switch in the

ON position.

CAUTION: Do not cut stems greater than

3/4 inch (19 mm). Use the trimmer only for cutting normal

shrubbery around houses and buildings.

Trimming Instructions

1. WORKING POSITION (fig. 7) – Maintain proper footing and

balance and do not overreach. Wear safety goggles, non-skid

footwear when trimming. Hold the unit firmly in both hands and

turn the unit on. Always hold the trimmer as shown in Figure 7,

with one hand on the switch handle (C) and one hand on the bail

handle (E). Never hold the unit by the blade guard (D).

2. TRIMMING NEW GROWTH (Fig. 8) – Using a wide, sweeping

motion, feeding the blade teeth through the twigs, is most

effective. A slight downward tilt of the blade in the direction of

motion gives the best cutting.

English

The cutting blades are made from high quality, hardened steel and with

normal usage, they will not require

FIG. 12

resharpening. However, if you

accidentally hit a wire fence (Fig. 12),

stones, glass, or other hard objects,

you may put a nick in the blade. There

is no need to remove this nick as long

as it does not interfere with the

movement of the blade. If it does

interfere, remove the battery and use a

fine toothed file or sharpening stone to

remove the nick. If you drop the

trimmer, carefully inspect it for damage.

If the blade is bent, housing cracked,

handles broken or if you see any other

condition that may affect the trimmer’s operation contact your local

DeWALT authorized service center

for repairs before putting it back into

use.

Fertilizers and other garden chemicals contain agents which greatly

accelerate the corrosion of metals. Do not store the unit on or adjacent

to fertilizers or chemicals.

With the battery removed, use only mild soap and a damp cloth to

clean the unit. Never let any liquid get inside the unit; never immerse

any part of the unit into a liquid. Prevent the blades from rusting by

applying a film of light machine oil after cleaning.

Accessories

WARNING: DO NOT use the hedge trimmer

with any type of accessory or attachment. Such usage might

be hazardous.

• READ INSTRUCTION MANUAL BEFORE USING. SAVE

INSTRUCTION MANUAL.

• Check the hedge for foreign objects such as wires or fences before

each use.

• KEEP HANDS ON HANDLES. DON’T OVERREACH.

• DO NOT USE UNDER WET CONDITIONS.

CAUTION: BLADE MAY COAST AFTER TURN OFF.

MAINTENANCE

WARNING: Remove battery pack before servicing,

cleaning or removing material from the hedge trimmer.

Your D

eWALT tool has been designed to operate over a long period

of time with minimum maintenance.

Continuous satisfactory operation depends on proper tool care and

regular cleaning.

WARNING: Before performing any maintenance,

switch off tool and remove battery.

Lubrication (Fig.11)

1. After use, carefully clean the blades with a resin solvent.

2. After cleaning, apply a light film of lubrication to the exposed blade.

3. Insert the battery and turn the trimmer vertical with the blades

toward the ground and run the trimmer for a few seconds to fully

disperse the lubrication.

4. Keeping your hands away from the

FIG. 11

blade, slide the sheath (G) over the

blade until it snaps into place as

shown in Figure 11.

English

In addition to the warranty, DeWALT tools are covered by our:

3 YEAR FREE SERVICE

eWALT will maintain the tool and replace worn parts caused by

normal use, for free, any time during the first year after purchase.

eWALT BATTERY PACKS

Product warranty voided if the battery pack is tampered with in any

way. D

eWALT is not responsible for any injury caused by tampering and

may prosecute warranty fraud to the fullest extent permitted by law.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of your

eWALT Power Tool, Laser, or Nailer for any reason, you can return it

within 90 days from the date of purchase with a receipt for a full refund

– no questions asked.

LATIN AMERICA: This warranty does not apply to products sold

in Latin America. For products sold in Latin America, see country

specific warranty information contained in the packaging, call the local

company or see website for warranty information.

FREE WARNING LABEL REPLACEMENT: If your warning labels

become illegible or are missing, call 1-800-4-D

eWALT (1-800-433-

9258) for a free replacement.

SER.

WARNING/AVERTISSEMENT/ADVERTENCIA

DEWALT INDUSTRIAL TOOL CO., BALTIMORE, MD 21286 U.S.A.

FOR SERVICE INFORMATION, CALL 1-800-4-DEWALT www.DEWALT.com MADE IN CHINA

DCHT820

TO REDUCE THE RISK OF INJURY, USER MUST READ INSTRUCTION MANUAL. USE PROPER EYE AND

RESPIRATORY PROTECTION. AFIN DE RÉDUIRE LE RISQUE

DE BLESSURES, L’UTILISATEUR DOIT LIRE LE MODE D’EMPLOI. UTILISER UNE PROTECTION OCULAIRE ET

RESPIRATOIRE ADÉQUATE. PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER EL MANUAL

DE INSTRUCCIONES. UTILICE PROTECCIÓN ADECUADA PARA LOS OJOS Y VÍAS RESPIRATORIAS.

GARDENING

APPLIANCE

Repairs

The charger and battery pack are not serviceable. There are no

serviceable parts inside the charger or battery pack.

To assure product SAFETY and RELIABILITY, repairs, maintenance

and adjustments (including brush inspection and replacement) should

be performed by a D

eWALT factory service center, a DeWALT

authorized service center or other qualified service personnel. Always

use identical replacement parts.

Thank you for your purchase. Register your product now for:

• WARRANTY SERVICE: Registering your product will help you

obtain more efficient warranty service in case there is a problem

with your product.

• CONFIRMATION OF OWNERSHIP: In case of an insurance

loss, such as fire, flood or theft, your registration of ownership will

serve as your proof of purchase.

• FOR YOUR SAFETY: Registering your product will allow us to

contact you in the unlikely event a safety notification is required

under the Federal Consumer Safety Act.

Three Year Limited Warranty

DeWALT will repair, without charge, any defects due to faulty materials

or workmanship for three years from the date of purchase. This

warranty does not cover part failure due to normal wear or tool abuse.

For further detail of warranty coverage and warranty repair information,

visit www.dewalt.com or call 1-800-4-D

eWALT (1-800-433-9258).

This warranty does not apply to accessories or damage caused where

repairs have been made or attempted by others. This warranty gives

you specific legal rights and you may have other rights which vary in

certain states or provinces.

English

TROUBLESHOOTING

Problem Solution

Unit will not start. • Check battery installation.

• Check battery charging requirements.

• Check that lock off is fully pushed

down prior to moving main trigger.

Battery won’t charge. • Insert battery into charger until red

charging light illuminates. Charge up

to 8 hours if battery is totally drained.

•

Plug charger into a working outlet. Refer

Important Charging Notes

for

more details.

• Check current at receptacle by

plugging an appliance.

• Check to see if receptacle is

connected to a light switch which

turns power off when you turn out the

lights.

• Move charger and appliance to a

surrounding air temperature of above

40°F (4.5°C) or below 105°F

(40.5°C).

Slow running, noisy,

or hot blades.

• Inspect for nicks and remove if possible.

• Lubricate blades.

• Bring to a D

eWALT factory service

center to straighten blade, blade

support, or teeth.

• Tighten bolts on the blade.

Français

Dénitions : lignes directrices en

matière de sécurité

Les définitions ci-dessous décrivent le niveau de danger pour

chaque mot-indicateur employé. Lire le mode d’emploi et porter

une attention particulière à ces symboles.

DANGER : indique une situation dangereuse imminente qui,

si elle n’est pas évitée, entraînera la mort ou des blessures

graves.

AVERTISSEMENT : indique une situation potentiellement

dangereuse qui, si elle n’est pas évitée, pourrait entraîner la

mort ou des blessures graves.

ATTENTION : indique une situation potentiellement

dangereuse qui, si elle n’est pas évitée, pourrait entraîner des

blessures légères ou modérées.

AVIS : indique une pratique ne posant aucun risque de

dommages corporels mais qui par contre, si rien n’est fait pour

l’éviter, pourrait poser des risques de dommages matériels.

POUR TOUTE QUESTION OU REMARQUE AU SUJET DE CET OUTIL

OU DE TOUT AUTRE OUTIL D

eWALT, COMPOSEZ LE NUMÉRO

SANS FRAIS : 1-800-4-D

eWALT (1-800-433-9258).

AVERTISSEMENT : afin de réduire le risque de blessures, lire

le mode d’emploi de l’outil.

Avertissements de sécurité généraux pour les

outils électriques

AVERTISSEMENT! Lire toutes les directives et toutes les

consignes de sécurité. Le non-respect des avertissements

et des directives pourrait se solder par un choc électrique, un

incendie et/ou une blessure grave.

CONSERVER TOUS LES AVERTISSEMENTS

ET TOUTES LES DIRECTIVES POUR UN

USAGE ULTÉRIEUR

Le terme « outil électrique » cité dans les avertissements se rapporte

à votre outil électrique à alimentation sur secteur (avec fil) ou par piles

(sans fil).

1) SÉCURITÉ DU LIEU DE TRAVAIL

a) Tenir l’aire de travail propre et bien éclairée. Les lieux

encombrés ou sombres sont propices aux accidents.

b) Ne pas faire fonctionner d’outils électriques dans un

milieu déflagrant, tel qu’en présence de liquides, de

gaz ou de poussières inflammables. Les outils électriques

produisent des étincelles qui pourraient enflammer la poussière

ou les vapeurs.

c) Éloigner les enfants et les personnes à proximité pendant

l’utilisation d’un outil électrique. Une distraction pourrait en

faire perdre la maîtrise à l’utilisateur.

2) SÉCURITÉ EN MATIÈRE D’ÉLECTRICITÉ

a) Les fiches des outils électriques doivent correspondre

à la prise. Ne jamais modifier la fiche d’aucune façon.

Ne jamais utiliser de fiche d’adaptation avec un outil

électrique mis à la terre. Le risque de choc électrique sera

réduit par l’utilisation de fiches non modifiées correspondant à

la prise.

b) Éviter tout contact physique avec des surfaces mises à la

terre comme des tuyaux, des radiateurs, des cuisinières

et des réfrigérateurs. Le risque de choc électrique est plus

élevé si votre corps est mis à la terre.

c) Ne pas exposer les outils électriques à la pluie ou à

l’humidité. La pénétration de l’eau dans un outil électrique

augmente le risque de choc électrique.

Français

brancher un outil électrique dont l’interrupteur est à la position

de marche risque de provoquer un accident.

d) Retirer toute clé de réglage ou clé avant de démarrer

l’outil. Une clé ou une clé de réglage attachée à une partie

pivotante de l’outil électrique peut provoquer des blessures

corporelles.

e) Ne pas trop tendre les bras. Conserver son équilibre en

tout temps. Cela permet de mieux maîtriser l’outil électrique

dans les situations imprévues.

f) S’habiller de manière appropriée. Ne pas porter de

vêtements amples ni de bijoux. Garder les cheveux, les

vêtements et les gants à l’écart des pièces mobiles. Les

vêtements amples, les bijoux ou les cheveux longs risquent de

rester coincés dans les pièces mobiles.

g) Si des composants sont fournis pour le raccordement de

dispositifs de dépoussiérage et de ramassage, s’assurer

que ceux-ci sont bien raccordés et utilisés. L’utilisation d’un

dispositif de dépoussiérage peut réduire les dangers engendrés

par les poussières.

4) UTILISATION ET ENTRETIEN D’UN OUTIL ÉLECTRIQUE

a) Ne pas forcer un outil électrique. Utiliser l’outil électrique

approprié à l’application. L’outil électrique approprié

effectuera un meilleur travail, de façon plus sûre et à la vitesse

pour laquelle il a été conçu.

b) Ne pas utiliser un outil électrique dont l’interrupteur

est défectueux. Tout outil électrique dont l’interrupteur est

défectueux est dangereux et doit être réparé.

c) Débrancher la fiche de la source d’alimentation et/ou du

bloc-piles de l’outil électrique avant de faire tout réglage

ou changement d’accessoire ou avant de ranger l’outil.

Ces mesures préventives réduisent les risques de démarrage

accidentel de l’outil électrique.

d) Ne pas utiliser le cordon de façon abusive. Ne jamais

utiliser le cordon pour transporter, tirer ou débrancher un

outil électrique. Tenir le cordon éloigné de la chaleur, de

l’huile, des bords tranchants et des pièces mobiles. Les

cordons endommagés ou enchevêtrés augmentent les risques

de choc électrique.

e) Pour l’utilisation d’un outil électrique à l’extérieur, se

servir d’une rallonge convenant à cette application.

L’utilisation d’une rallonge conçue pour l’extérieur réduira les

risques de choc électrique.

f) S’il est impossible d’éviter l’utilisation d’un outil électrique

dans un endroit humide, brancher l’outil dans une prise

ou sur un circuit d’alimentation dotés d’un disjoncteur de

fuite à la terre (GFCI). L’utilisation de ce type de disjoncteur

réduit les risques de choc électrique.

3) SÉCURITÉ PERSONNELLE

a) Être vigilant, surveiller le travail effectué et faire preuve

de jugement lorsqu’un outil électrique est utilisé. Ne

pas utiliser d’outil électrique en cas de fatigue ou sous

l’influence de drogues, d’alcool ou de médicaments. Un

simple moment d’inattention en utilisant un outil électrique peut

entraîner des blessures corporelles graves.

b) Utiliser des équipements de protection individuelle.

Toujours porter une protection oculaire. L’utilisation

d’équipements de protection comme un masque antipoussière,

des chaussures antidérapantes, un casque de sécurité ou des

protecteurs auditifs lorsque la situation le requiert réduira les

risques de blessures corporelles.

c) Empêcher les démarrages intempestifs. S’assurer que

l’interrupteur se trouve à la position d’arrêt avant de relier

l’outil à une source d’alimentation et/ou d’insérer un bloc-

piles, de ramasser ou de transporter l’outil. Transporter un

outil électrique alors que le doigt repose sur l’interrupteur ou

Français

entre les deux bornes. Le court-circuit des bornes du bloc-

piles risque de provoquer des brûlures ou un incendie.

d) En cas d’utilisation abusive, le liquide peut gicler hors

du bloc-piles; éviter tout contact avec ce liquide. Si un

contact accidentel se produit, laver à grande eau. Si le

liquide entre en contact avec les yeux, obtenir également

des soins médicaux. Le liquide qui gicle hors du bloc-piles

peut provoquer des irritations ou des brûlures.

6) RÉPARATION

a) Faire réparer l’outil électrique par un réparateur

professionnel en n’utilisant que des pièces de rechange

identiques. Cela permettra de maintenir une utilisation

sécuritaire de l’outil électrique.

Avertissements de sécurité pour le

taille-haie

• Tenir toutes les parties du corps loin de la lame de l’outil de

coupe. Ne pas enlever la matière coupée ni tenir la matière

à couper lorsque les lames fonctionnent. S’assurer que

l’interrupteur est en position d’arrêt lors du dégagement de la

matière coincée. Les lames continuent de fonctionner après

l’arrêt de l’outil. Un moment d’inattention, durant l’utilisation d’un

taille-haie, peut se solder par de graves blessures corporelles.

• Transporter le taille-haie par sa poignée une fois la lame de

l’outil de coupe arrêtée. Une manutention adéquate du taille-

haie permet de réduire les blessures corporelles possibles avec les

lames de l’outil de coupe

DANGER: Tenir les mains loin de la lame. Tout

contact avec la lame risque de causer de graves blessures corporelles.

• Tenir l’outil électrique uniquement par sa surface de prise

isolée, car la lame de l’outil de coupe pourrait entrer en

d) Ranger les outils électriques hors de la portée des

enfants et ne permettre à aucune personne n’étant pas

familière avec un outil électrique ou son mode d’emploi

d’utiliser cet outil. Les outils électriques deviennent dangereux

entre les mains d’utilisateurs inexpérimentés.

e) Entretien des outils électriques. Vérifier si les pièces

mobiles sont mal alignées ou coincées, si des pièces sont

brisées ou présentent toute autre condition susceptible

de nuire au bon fonctionnement de l’outil électrique.

En cas de dommage, faire réparer l’outil électrique

avant toute nouvelle utilisation. Beaucoup d’accidents sont

causés par des outils électriques mal entretenus.

f) S’assurer que les outils de coupe sont aiguisés et

propres. Les outils de coupe bien entretenus et affûtés

sont moins susceptibles de se coincer et sont plus faciles à

maîtriser.

g) Utiliser l’outil électrique, les accessoires, les forets,

etc. conformément aux présentes directives en tenant

compte des conditions de travail et du travail à effectuer.

L’utilisation d’un outil électrique pour toute opération autre que

celle pour laquelle il a été conçu est dangereuse.

5) UTILISATION ET ENTRETIEN DU BLOC-PILES

a) Ne recharger l’outil qu’au moyen du chargeur précisé par

le fabricant. L’utilisation d’un chargeur qui convient à un type

de bloc-piles risque de provoquer un incendie s’il est utilisé avec

un autre type de b loc-piles.

b) Utiliser les outils électriques uniquement avec les blocs-

piles conçus à cet effet. L’utilisation de tout autre bloc-piles

risque de causer des blessures ou un incendie.

c) Lorsque le bloc-piles n’est pas utilisé, le tenir éloigné

des objets métalliques, notamment des trombones, de

la monnaie, des clés, des clous, des vis ou autres petits

objets métalliques qui peuvent établir une connexion

Français

approuvé, comme les masques antipoussières spécialement conçus

pour filtrer les particules microscopiques.

• L’étiquette apposée sur votre outil peut comprendre les symboles

suivants. Les symboles et leurs définitions sont indiqués ci-après :

V ................... volts

A ................... ampères

Hz ................. hertz

W .................. watts

min ............... minutes

ou AC ...... courant alternatif

ou DC ... courant continu

................. classe I

fabrication (mis

à la terre)

................. fabrication

classe II (double

isolation)

o ................. vitesse à vide

…/min .......... par minute

................. borne de terre

.................. symbole

d’avertissement

r/min ............. tours par minute

CSPM ........... couper les

coups par

minute

Consignes de sécurité importantes propres à

tous les blocs-piles

Pour commander un bloc-piles de rechange, s’assurer d’inclure son

numéro de catalogue et sa tension. Consulter le tableau en dernière

page de ce manuel pour connaître les compatibilités entre chargeurs

et blocs-piles.

Le bloc-piles n’est pas totalement chargé d’usine. Avant d’utiliser le

bloc-piles et le chargeur, lire les consignes de sécurité ci-dessous.

Puis suivre la procédure de charge indiquée.

LIRE TOUTES LES CONSIGNES

• Ne pas recharger ou utiliser un bloc-piles en milieu déflagrant,

en présence, par exemple, de poussières, gaz ou liquides

inflammables. Le fait d’insérer ou retirer un bloc-piles de son chargeur

pourrait causer l’inflammation de poussières ou d’émanations.

contact avec des fils cachés ou son propre cordon. Une

lame qui entre en contact avec un fil sous tension peut mettre sous

tension des pièces métalliques dénudées de l’outil électrique et

ainsi donner une décharge électrique à l’opérateur.

• Utiliser les deux mains pour faire fonctionner le taille-haie.

Utiliser une main seulement risque d’entraîner la perte

de maîtrise de l’outil et de causer de graves blessures

corporelles.

• Rallonge éloigner de la zone de coupe. Au cours de

l'opération, la rallonge peut être cachée dans les buissons et peut

être accidentellement coupée par la lame.

• Vérifier la couverture pour les corps étrangers, par exemple

les clôtures de fil.

ATTENTION: Ne pas exposer à la pluie.

AVERTISSEMENT : Retirer

immédiatement la fiche de la prise si la rallonge électrique est

endommagée ou coupée.

AVERTISSEMENT : les scies, meules, ponceuses, perceuses ou

autres outils de construction peuvent produire des poussières

contenant des produits chimiques reconnus par l’État californien pour

causer cancers, malformations congénitales ou être nocifs au système

reproducteur. Parmi ces produits chimiques, on retrouve:

• Le plomb dans les peintures à base de plomb;

• La silice cristallisée dans les briques et le ciment, ou autres

produits de maçonnerie; et

• L’arsenic et le chrome dans le bois ayant subi un traitement

chimique.

Le risque associé à ces expositions varie selon la fréquence de ces

types de travaux. Pour réduire l’exposition aux produits chimiques :

travailler dans un local bien ventilé et utiliser du matériel de sécurité

Français

qu’aucun objet métallique n’entre en contact avec les bornes

à découvert du bloc-piles. Par exemple, éviter de placer un bloc-

piles dans un tablier, une poche, une boîte à outils ou un tiroir, etc.

contenant des objets tels que des clous, des vis, des clés, etc. Le fait

de transporter des bloc-piles comporte des risques d’incendie,

car les bornes des piles pourraient entrer, par inadvertance,

en contact avec des objets conducteurs, tels que : clés,

pièces de monnaie, outils ou autres. La réglementation sur les

produits dangereux (Hazardous Material Regulations) du département

américain des transports interdit, en fait, le transport des piles pour le

commerce ou dans les avions (ex: dans les bagages enregistrés ou à

main) À MOINS qu’elles ne soient correctement protégées contre tout

court-circuit. Aussi lors du transport individuel de blocs-piles, s’assurer

que leurs bornes sont bien protégées et isolées de tout matériau

pouvant entrer en contact avec elles et provoquer un court-circuit.

Transport

Les blocs-piles DeWALT sont conformes à tous les règlements

d’expédition applicables, prescrits par les normes industrielles et

juridiques, dont notamment les Recommandations de l’ONU relatives

au transport des marchandises dangereuses, la Réglementation des

marchandises dangereuses de l’Association du Transport Aérien

International (IATA), la réglementation du Code maritime international

des marchandises dangereuses (IMDG) et le règlement du département

des Transports des É.-U. Les cellules et les blocs-piles au lithium-ion

ont été testés selon l’article 38.3 des Recommandations de l’ONU

relatives au transport de marchandises dangereuses, Manuel des

essais et des critères.

L’expédition ou le transport du bloc-piles dans ce produit fait l’objet

de restrictions, et il peut être classé comme un matériau dangereux

de classe 9.

• NE JAMAIS forcer l’insertion d’un bloc-piles dans un

chargeur. NE modifier un bloc-piles d’AUCUNE façon pour le

faire rentrer dans un chargeur incompatible, car il pourrait se

briser et causer des dommages corporels graves. Consulter

le tableau en dernière page de ce manuel pour connaître les

compatibilités entre chargeurs et blocs-piles.

• Recharger les blocs-piles exclusivement dans des chargeurs

eWALT.

• NE PAS éclabousser le bloc-piles ou l’immerger dans l’eau ou

dans tout autre liquide. Si l’appareil est mouillé, le laisser sécher

pendant au moins 48heures.

• Ne pas entreposer ou utiliser l’appareil et le bloc-piles en

présence de températures ambiantes pouvant excéder

40 °C (105 °F) (comme dans des hangars ou des bâtiments

métalliques l’été). Pour préserver leur durée de vie, entreposer

les blocs-piles dans un endroit frais et sec.

REMARQUE : ne pas mettre un bloc-piles dans un outil dont

la gâchette est verrouillée en position de marche. Ne jamais

bloquer l’interrupteur en position de MARCHE.

AVERTISSEMENT : risques d’incendie.

Ne jamais tenter d’ouvrir le bloc-piles pour quelque raison que ce soit.

Si le boîtier du bloc-piles est fissuré ou endommagé, ne pas l’insérer

dans un chargeur. Ne pas écraser, laisser tomber, ou endommager les

blocs-piles. Ne pas utiliser un bloc-piles ou un chargeur qui a reçu un

choc violent, ou si l’appareil est tombé, a été écrasé ou endommagé

de quelque façon que ce soit (p. ex. percé par un clou, frappé d’un

coup de marteau, piétiné). Les blocs-piles endommagés doivent être

renvoyés à un centre de réparation pour y être recyclés.

AVERTISSEMENT : risques d’incendie.

Au moment de ranger ou transporter le bloc-piles, s’assurer

La page charge ...

DeWalt DCHT820P1WR320B Manuel utilisateur

Marque: DeWalt

Modèle: DCHT820P1WR320B

Catégorie: Taille-haies électriques

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: DeWalt DCHT820P1WR320B User manual
español: DeWalt DCHT820P1WR320B Manual de usuario

DeWalt DCHT820P1WR320B Manuel utilisateur

DeWalt DCHT820P1WR320B Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents