Simplicity 076451-01 Manuel utilisateur

Installation and Operation Manual

35kW 48kW 60kW

Single Phase and Three Phase

Liquid Cooled Standby Generator System

This generator is rated in accordance with UL (Underwriters Laboratories) 2200 (stationary engine generator

assemblies) and CSA (Canadian Standards Association) standard C22.2 No. 100-4 (motors and generators).

80022440USCN

Revision A

2 BRIGGSandSTRATTON.COM

Thank you for purchasing this quality-built Milbank® generator. We are pleased that you’ve placed your confidence in the

Milbank brand. When operated and maintained according to the instructions in this manual, your generator will provide many

years of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with standby generators and

how to avoid them.

Save these instructions for future reference.

This generator system requires professional installation before use. The installer should follow the installation instructions

completely.

Where to Find Us

You never have to look far to find support and service for your generator. Consult your Yellow Pages. There are many

authorized service dealers worldwide that provide quality service. You can also contact Technical Service by phone at

800-732-2989 between 8:00 AM and 5:00 PM central time or click on Dealer Locator at www.briggsandstratton.com, which

provides a list of authorized dealers.

For Future Reference

Please fill out the information below and keep with your receipt. Have this information at hand if it becomes necessary to

contact your installer or authorized dealer regarding service or repair of the unit.

DATE OF PURCHASE

GENERATOR

Model Number

Serial Number

Model Number

Model Revision

Serial Number

ENGINE

3

Table Of Contents

Important Safety Instructions .....................4

General Information..............................7

Installer Responsibilities ................................... 7

Owner Responsibilities .................................... 7

Battery Warmer Kit ....................................... 7

Installation Factors to Consider ............................. 8

Delivery Inspection ....................................... 8

Generator Location Considerations .......................... 8

Installation .....................................9

TO REDUCE THE RISK OF CARBON MONOXIDE POISONING 9

TO REDUCE THE RISK OF FIRE .......................... 11

Other Location Requirements.............................. 12

Electrical and Fuel Inlet Locations .......................... 12

Concrete Slab .......................................... 12

Lifting the Generator ..................................... 13

Planning the Gaseous Fuel Installation ............14

Fuel Pipe Sizing......................................... 14

Type of Fuel to Use ...................................... 15

Fuel Conversion......................................... 15

Fuel Pressure........................................... 15

Power Loss ............................................ 15

Fuel Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Power Connections .............................17

Briggs & Stratton Controller Connections .................... 18

InteliNano Controller Connections .......................... 19

InteliLite Controller Connections ........................... 20

Battery ................................................ 21

Final Installation Considerations ........................... 21

Initial Start-up (No Load).................................. 22

Features and Controls...........................23

Access Panels .......................................... 23

Component Locations .................................... 24

Maintenance ...................................25

Cleaning the Generator................................... 25

Engine Air Cleaner....................................... 25

Electrical System Maintenance ............................ 26

Exhaust System Maintenance ............................. 26

Troubleshooting................................27

Generator Specifications ........................28

Wiring Diagrams................................29

1-Phase Briggs & Stratton ................................ 30

3-Phase InteliNano ...................................... 32

1-Phase InteliLite ........................................ 36

3-Phase InteliLite ........................................ 38

575-Volt InteliLite........................................ 42

4.3L Engine ............................................ 44

5.7L Engine ............................................ 46

4 BRIGGSandSTRATTON.COM

Important Safety Instructions

SAVE THESE INSTRUCTIONS - This manual contains

important instructions that should be followed during

installation and maintenance of the generator and batteries.

Safety Symbols and Meanings

The safety alert symbol indicates a potential personal

injury hazard. A signal word (DANGER, WARNING, or

CAUTION) is used with the alert symbol to designate a

degree or level of hazard seriousness. A safety symbol

may be used to represent the type of hazard. The signal

word NOTICE is used to address practices not related to

personal injury.

DANGER

indicates a hazard which, if not avoided, will

result in death or serious injury.

WARNING

indicates a hazard which, if not avoided, could

result in death or serious injury.

CAUTION

indicates a hazard which, if not avoided, could

result in minor or moderate injury.

NOTICE

indicates an action that could result in damage to

the product.

The manufacturer cannot anticipate every circumstance that

might involve a hazard. The warnings in this manual, and the

tags and decals affixed to the unit are, therefore, not all-

inclusive. If you use a procedure, work method or operating

technique that the manufacturer does not specifically

recommend, you must satisfy yourself that it is safe for you

and others. You must also make sure that the procedure,

work method or operating technique that you choose does

not render the generator system unsafe.

WARNING

The engine exhaust from this product

contains chemicals known to the State of California to

cause cancer, birth defects, or other reproductive harm.

WARNING

Certain components in this product and

related accessories contain chemicals known to the

State of California to cause cancer, birth defects, or other

reproductive harm. Wash hands after handling.

WARNING

Running engine gives off carbon monoxide,

an odorless, colorless, poison gas.

Breathing carbon monoxide could result in death,

serious injury, headache, fatigue, dizziness,

vomiting, confusion, seizures, nausea or fainting.

• Operate this product ONLY outdoors in an area that

will not accumulate deadly exhaust gas.

• Keep exhaust gas away from any windows, doors,

ventilation intakes, soffit vents, crawl spaces, open

garage doors or other openings that can allow exhaust

gas to enter inside or be drawn into a potentially

occupied building or structure.

• Carbon monoxide detector(s) MUST be installed and

maintained indoors according to the manufacturer’s

instructions/recommendations. Smoke alarms cannot

detect carbon monoxide gas.

WARNING

Storage batteries give off explosive

hydrogen gas during recharging.

Slightest spark will ignite hydrogen and cause

explosion, resulting in death or serious injury.

Battery electrolyte fluid contains acid and is

extremely caustic.

Contact with battery contents could cause severe

chemical burns.

A battery presents a risk of electrical shock and

high short circuit current.

• DO NOT dispose of battery in a fire. Recycle battery.

• DO NOT allow any open flame, spark, heat, or lit

cigarette during and for several minutes after charging a

battery.

• DO NOT open or mutilate the battery.

• Wear protective goggles, rubber apron, rubber boots and

rubber gloves.

• Remove watches, rings, or other metal objects.

• Use tools having insulated handles.

Explosion

Fire

Electrical Shock

Rotating Parts

Hot Surface

Toxic Fumes

Chemical BurnExplosive PressureAuto Start

Lift Hazard

Read Manual

5

WARNING

Generator produces hazardous voltage.

Failure to properly ground generator could result

in electrocution.

Failure to isolate generator from utility power could result

in death or serious injury to electric utility workers due to

backfeed of electrical energy.

• DO NOT touch bare wires or bare receptacles.

• DO NOT use generator with electrical cords which are

worn, frayed, bare or otherwise damaged.

• DO NOT handle generator or electrical cords while

standing in water, while barefoot, or while hands or

feet are wet.

• If you must work around a unit while it is operating,

stand on an insulated dry surface to reduce the risk of

a shock hazard.

• DO NOT allow unqualified persons or children to

operate or service generator.

• In case of an accident caused by electrical shock,

immediately shut down the source of electrical

power and contact the local authorities. Avoid direct

contact with the victim.

• Despite the safe design of the generator, operating

this equipment imprudently, neglecting its

maintenance or being careless could cause possible

injury or death.

• Remain alert at all times while working on this

equipment. Never work on the equipment when you

are physically or mentally fatigued.

• Before performing any maintenance on the generator,

disconnect the battery cable indicated by a

NEGATIVE, NEG or (-) first. When finished, reconnect

that cable last.

• After your system is installed, the generator may

crank and start without warning any time there is a

power failure. To prevent possible injury, always set the

generator’s system switch to OFF, remove the service

disconnect from the disconnect box AND remove the

15 Amp fuse BEFORE working on the equipment.

WARNING

Propane and Natural Gas are extremely

flammable and explosive, which could cause

burns, fire or explosion resulting in death or

serious injury.

• Install the fuel supply system according to NFPA 37

and other applicable fuel-gas codes.

• Before placing the generator into service, the fuel

system lines must be properly purged and leak tested.

• After the generator is installed, you should inspect the

fuel system periodically.

• NO leakage is permitted.

• DO NOT operate engine if smell of fuel is present or

other explosive conditions exist.

• DO NOT smoke around the generator. Wipe up any

oil spills immediately. Ensure that no combustible

materials are left in the generator compartment. Keep

the area near the generator clean and free of debris.

WARNING

Exhaust heat/gases could ignite

combustibles or structures resulting in death

or serious injury.

Contact with muffler area could cause burns

resulting in serious injury.

• DO NOT touch hot parts and AVOID hot exhaust

gases.

• Allow equipment to cool before touching.

• Exhaust outlet side of weatherproof enclosure must

have at least 5 ft. (1.5m) minimum clearance from any

structure, shrubs, trees or any kind of vegetation.

• Standby generator weatherproof enclosure must be

at least 5 ft. (1.5m) from windows, doors, any wall

opening, shrubs or vegetation over 12 inches (30.5

cm) in height.

• Standby generator weatherproof enclosure must have

a minimum of 5 ft. (1.5 m) overhead clearance from

any structure, overhang, or trees.

• DO NOT place weatherproof enclosure under a deck

or other type of structure that may confine airflow.

• Use only flexible fuel line provided. Connect provided

fuel line to generator. DO NOT use with or substitute

any other flexible fuel line.

• Smoke detector(s) MUST be installed and maintained

indoors according to the manufacturer’s instructions/

recommendations. Carbon monoxide alarms cannot

detect smoke.

• Keep at least minimum distances shown in General

Location Guidelines to insure for proper generator

cooling and maintenance clearances.

• Replacement parts must be the same and installed in

the same position as the original parts.

WARNING

Hazardous Voltage - Contact with power lines

could cause electric shock or burns, resulting in

death or serious injury.Lifting Hazard / Heavy Object

- Could result in serious injury.

• If lifting or hoisting equipment is used, DO NOT

contact any power lines.

• DO NOT lift or move generator without assistance.

• DO NOT lift unit by roof as damage to generator

will occur.

6 BRIGGSandSTRATTON.COM

CAUTION

Installing the 15A fuse could cause the

engine to start at any time without warning resulting

in minor or moderate injury.

• Observe that the 15 Amp fuse has been removed from

the control panel for shipping.

• DO NOT install this fuse until all plumbing and wiring

has been completed and inspected.

WARNING

Moving parts could crush and cut.

Starter and other rotating parts could

entangle hands, hair, clothing, or

accessories resulting in serious injury.

• NEVER operate generator without protective

housings, covers, or guards in place.

• DO NOT wear loose clothing, jewelry or anything that

could be caught in the starter or other rotating parts.

• Tie up long hair and remove jewelry.

• Before servicing, remove 15 Amp fuse from control

panel and disconnect Negative (NEG or -) battery

cable.

WARNING

Hot pressurized coolant could cause serious

injury.

• DO NOT open radiator cap when hot.

• Before servicing, allow coolant to cool.

CAUTION

Excessively high operating speeds could

result in minor injury and/or equipment damage.

Excessively low speeds impose a heavy load on generator.

• DO NOT tamper with governed speed. Generator

supplies correct rated frequency and voltage when

running at governed speed.

• DO NOT modify generator in any way.

NOTICE

Improper treatment of generator could damage it

and shorten its life.

• Use generator only for intended uses.

• If you have questions about intended use, contact your

authorized dealer.

• Operate generator only on level surfaces.

• Adequate, unobstructed flow of cooling and ventilating

air is critical to correct generator operation.

• The access panels/doors must be installed whenever

the unit is running.

• DO NOT expose generator to excessive moisture,

dust, dirt, or corrosive vapors.

• Remain alert at all times while working on this

equipment. Never work on the equipment when you

are physically or mentally fatigued.

• DO NOT start engine with air cleaner or air cleaner

cover removed.

• DO NOT insert any objects through cooling slots.

• DO NOT use the generator or any of its parts as a

step. Stepping on the unit could cause stress and

break parts. This may result in dangerous operating

conditions from leaking exhaust gases, fuel leakage,

oil leakage, etc.

• If connected devices overheat, turn them off and

disconnect them from generator.

• Shut off generator if:

-electrical output is lost;

-equipment sparks, smokes, or emits flames;

-unit vibrates excessively or makes unusual noises.

NOTICE

Exceeding the generator wattage/amperage

capacity could damage the generator and/or electrical

devices connected to it. Start generator and let engine

stabilize before connecting electrical loads.

7

General Information

For most applications, the Installation and Operation Manual

contains all the information required to properly install,

operate, and maintain the generator.

Every effort has been made to ensure that information in this

manual is accurate and current. However, we reserve the

right to change, alter, or otherwise improve the product and

this document at any time without prior notice.

Ensure that this manual is given to the owner after the

installation has been completed.

Equipment Description

This product is intended only for use as an optional

generator system to provide an alternate source of electric

power and to serve loads such as heating, refrigeration

systems, and communication systems that, when stopped

during any power outage, could cause discomfort or

inconvenience.

NOTICE Only models equipped with the MRS19 controller

qualify for either an emergency standby or legally required

standby system as defined by NFPA 70 (NEC). For complete

information on these types of installations, consult NFPA 70

and NFPA 110.

• Emergency generator systems are intended to

automatically supply illumination, power, or both, to

designated areas and equipment in the event of failure

of the normal supply. Emergency systems may also

provide power for such functions as ventilation where

essential to maintain life, where current interruption of

the normal supply would produce serious life safety or

health hazards.

• Legally required standby generator systems are

intended to automatically supply power to selected

loads in the event of failure of the normal source which

could create hazards or hamper rescue or fire-fighting

operations.

Before Installation

Only current licensed electrical and plumbing professionals

should attempt generator system installations. Installations

must strictly comply with all applicable codes, industry

standards, laws, and regulations.

In some areas you may need electrical permits for installing

the generator, building permits for intalling gas lines, and

permits for noise allowances. The installer should check local

codes and obtain the necessary permits before installing the

system.

The generator warranty is VOID unless the system is

installed by licensed electrical and plumbing professionals.

Installer Responsibilities

• Read and observe the safety instructions.

• Install only a UL-approved transfer switch that is

compatible with the generator.

• Read and follow the instructions in this installation and

operation manual.

• Installation must strictly comply with all applicable

codes, industry standards, laws, and regulations.

• Allow sufficient room on all sides of the generator for

maintenance and servicing.

Owner Responsibilities

• Read and follow the instructions in this installation and

operation manual.

• Follow a regular schedule for maintaining and using

the generator, as specified in this manual.

• Carbon monoxide detector(s) MUST be installed and

maintained indoors according to the manufacturer’s

instructions and recommendations. Smoke alarms

cannot detect carbon monoxide gas.

• Smoke detector(s) MUST be installed and maintained

indoors according to the manufacturer’s instructions

and recommendations. Carbon monoxide alarms

cannot detect smoke.

Battery Warmer Kit

If operating the generator below 30°F (-1°C), it is

recommended to install the optional Battery Warmer Kit.

The battery warmer is available separately through servicing

dealers under part number 6343.

8 BRIGGSandSTRATTON.COM

Installation Factors to Consider

The illustrations shown in this manual are for typical

circumstances. They are meant to familiarize you with the

installation options available for the generator.

Federal and local codes, appearance, noise levels, fuel

types, and distances are installation factors that must be

considered. Remember that, as the distance increases

from the existing electrical service and gaseous fuel supply,

and the number of bends in the fuel supply increases,

compensations must be made for piping and wiring

materials. This is necessary to comply with local codes

and overcome electrical voltage drops and gaseous fuel

pressure drops.

The factors mentioned above will have a direct effect on the

overall price of the generator installation.

Delivery Inspection

Avoid damage from dropping, bumping, or collision with the

shipping carton. Store and unpack the unit with the proper

side up, as noted on the shipping carton.

After removing the carton, carefully inspect the generator for

any damage that may have occurred during shipment.

If loss or damage is found at time of delivery, have the

person(s) making delivery note the loss or damage on the

freight bill and affix his signature under the consignor’s

memo of loss or damage. If the loss or damage is noted after

delivery, separate the damaged materials and contact the

carrier for claim procedures. Missing or damaged parts are

not warranted.

The standby generator system is supplied with:

• Fully-serviced coolant system

• Fully-serviced oil/lubricating system

• Flexible fuel hook-up hose

• Installation and Operation Manual

• Spare access door keys

• Spare 15 Amp ATO-type fuse

• Touch up paint

Not Supplied:

• Carbon monoxide detector(s)

• Smoke detector(s)

• Starting battery

• Reinforced concrete pad

• Connecting wire and conduit

• Fuel supply valves/plumbing

• 60” lengths of 2” Schedule 40 pipe (NOT conduit)

• Crane, lifting straps, chains or cables, spreader bar

• Torque screwdriver, 5 to 50 inch-pound range

• Voltage/frequency meter

• Various special tools or equipment

Generator Location Considerations

The installation location of the generator has a direct effect

on:

1. The amount of plumbing required to fuel the generator.

2. The amount of wiring required to control and connect

the generator.

3. The safety of the installation regarding exhaust gas and

carbon monoxide hazards, fire risks, proximity to other

utilities, and exposure to weather elements.

Specific location guidelines are discussed in the next

section. The owner and installer should consult one another

to determine how the site might affect installation costs and

compliance with local codes and standards.

9

C

B

Installation

Before deciding on the final placement of the generator, the owner and installer must discuss and understand several

location guidelines. There are two critical safety concerns to be addressed - carbon monoxide poisoning and the risk of fire,

as follows:

WARNING Running engine gives off carbon monoxide, an

odorless, colorless, poison gas.

Breathing carbon monoxide could result in death, serious

injury, headache, fatigue, dizziness, vomiting, confusion,

seizures, nausea or fainting.

• Operate this product ONLY outdoors in an area that will not

accumulate deadly exhaust gas.

• Keep exhaust gas away from any windows, doors, ventilation

intakes, soffit vents, crawl spaces, open garage doors or other

openings that can allow exhaust gas to enter inside or be

drawn into a potentially occupied building or structure.

• Carbon monoxide detector(s) MUST be installed and

maintained indoors according to the manufacturer’s instructions

and recommendations. Smoke alarms cannot detect carbon

monoxide gas.

WARNING

Exhaust heat or gases could ignite

combustibles or structures resulting in death or

serious injury.

• Exhaust outlet end of standby enclosure must be at

least 5 ft (1.5 m) from any structure, shrubs, trees or

any kind of vegetation.

• Standby enclosure must be at least 5 ft (1.5 m) from

windows, doors, any wall opening, shrubs, or

vegetation over 12 inches (30.5 cm) in height.

• Standby enclosure must have at least 5 feet (1.5 m)

overhead clearance from any structure, overhang, or trees.

• DO NOT place standby enclosure under a deck or

other type of structure that may confine airflow.

• USE ONLY the flexible steel fuel line provided.

Connect provided fuel line to generator. DO NOT use

with or substitute any other flexible fuel line.

• Smoke detectors MUST be installed and maintained

indoors according to the manufacturer’s instructions

and recommendations. Carbon monoxide alarms

cannot detect smoke.

TO REDUCE THE RISK OF CARBON MONOXIDE POISONING

Follow the installation requirements listed below. The figure below illustrates potential points of entry for carbon monoxide

gas.

Ensure that generator exhaust gas is kept away from:

• Overhead doors (B, shown above)

• Entrance doors (C, shown above)

• Windows (not shown)

• Other openings that could allow exhaust gas to enter

inside or be drawn into a potentially occupied building

or structure.

10 BRIGGSandSTRATTON.COM

All fossil fuel burning products, such as standby

generators, emit carbon monoxide (CO) gas in the

engine exhaust. CO gas is odorless, colorless and

tasteless and is unlikely to be noticed until a person is

overcome. CO gas can kill you. It is required that the

following be included as part of the installation:

• Install the generator outdoors in an area that

will not accumulate deadly exhaust gas.

• DO NOT install the generator where exhaust

gas could accumulate and enter inside or be

drawn into a potentially occupied building or

structure.

• Nearby structures may be exposed to the engine

exhaust from the unit and must be considered

when installing the standby generator.

• Wind and air currents should be taken into

consideration when positioning the generator.

Place the generator in an area where winds will

carry the exhaust gas away from any potentially

occupied building or structure.

• DO NOT place the standby generator in any area

where leaves or debris normally accumulate.

• By law, many states require a fully operating

Carbon Monoxide (CO) detector in homes

and other structures occupied by people.

Carbon monoxide detectors (shown below)

MUST be installed and maintained indoors

according to the manufacturer’s instructions and

recommendations. A carbon monoxide detector

is an electronic device that detects hazardous

levels of CO. When there is a buildup of CO,

the monitor will alert the occupants by flashing

a visual indicator light and sounding an alarm.

Smoke alarms cannot detect CO gas.

• Direct the standby generator exhaust (A, shown

below) away from or parallel to the building or

structure. DO NOT direct the generator exhaust

towards a potentially occupied building, structure,

windows, doors, ventilation intakes, soffit vents,

crawl spaces, open garage doors, or other openings

where exhaust gas could accumulate and enter

inside or be drawn into a potentially occupied

building or structure.

The engine exhaust exits the top of the housing (A).

A

11

TO REDUCE THE RISK OF FIRE

Follow the installation requirements listed below. The figures below illustrate the minimum distances from structures and

vegetation to reduce the risk of fire.

The National Fire Protection Association (NFPA) standard NFPA 37 establishes criteria for minimizing the hazard of

fire during the installation and operation of stationary combustion engines. NFPA 37 limits the spacing of an enclosed

generator from openings in walls, structures and combustible materials outside the enclosure. The following generator

placement requirements are based on compliance to NFPA 37 2010 section 4.1.4.

5 ft (1.5 m) min.

Standby

5 ft (1.5 m) min.

Exhaust

B

A

5 ft (1.5 m) min.

Standby

5 ft (1.5 m) min.

Exhaust

A

B

5 ft (1.5 m) min.

Standby

5 ft (1.5 m) min.

Exhaust

B

A

A Standby enclosure must be at least 5 ft (1.5 m)

from windows, doors, any wall opening, shrubs,

or vegetation over 12 inches (30.5 cm) in height.

B Exhaust outlet end of standby enclosure must

be at least 5 ft (1.5 m) from any structure,

shrubs, trees, or any kind of vegetation.

C Standby enclosure must have at least 5 feet (1.5 m)

overhead clearance from any structure, overhang, or

trees.

DO NOT place standby enclosure under a deck or other

type of covered structure that may confine airflow.

5 ft (1.5 m) min.

Standby

5 ft (1.5 m) min.

Exhaust

B

A

B

C

12 BRIGGSandSTRATTON.COM

Other Location Requirements

• Place the standby generator in a prepared location

that is flat and has provisions for water drainage.

• Install the standby generator in a location where

sump pump discharge, rain gutter down spouts, roof

run-off, landscape irrigation, or water sprinklers will

not flood the unit or spray the enclosure, or enter any

air inlet or outlet openings.

• Install the standby generator where it will not affect

or obstruct any utility services (including covered,

concealed, and underground), such as telephone,

electric, fuel (natural gas / LPG vapor), irrigation, air

conditioning, cable, septic, sewer, well, etc.

• Install the standby generator where leaves, grass,

snow, etc will not obstruct air inlet and outlet

openings. If prevailing winds will cause blowing or

drifting, a windbreak may be needed to protect the

unit.

Electrical and Fuel Inlet Locations

A through-slab power cable stub-up is recommended.

If a stub-up is not used, (B, below) indicates the

recommended location for punching a hole to attach

power conduit. The 1” (25.4 mm) NPT fuel inlet connector

(A) is shown for reference.

Concrete Slab

The generator must be installed on a reinforced concrete

slab, constructed as follows:

• 28 day compression strength of 3000 psi (200 MPa)

• Minimum 5” (13 cm) thick

• Minimum 6” (15 cm) wider than the standby enclosure

on all sides

• Strengthen slab with No. 6 reinforcing bars on 12” (30.5

cm) centers or 8 ga. steel wire fabric with 6” (15 cm)

centers

• Avoid placing reinforcement in the entrance stub-up

area

The following dimensions will be needed to properly size and

configure the slab. Refer to figure at right:

A - Enclosure dimensions

• 35kW = 88” (224 cm) long x 37” (94 cm) wide

• 48kW = 88” (224 cm) long x 37” (94 cm) wide

• 60kW = 96” (244 cm) long x 37” (94 cm) wide

B - Generator mounting holes

• 35kW = 85” (216 cm) long x 34.25” (87 cm) wide

• 48kW = 85” (216 cm) long x 34.25” (87 cm) wide

• 60kW = 94” (239 cm) long x 34.25” (87 cm) wide

C - Fuel inlet location

• 35kW = 45.5” (116 cm)

• 48kW = 45.5” (116 cm)

• 60kW = 52” (132 cm)

D - Entrance stub-up area

• 35kW = 10.5” (27 cm) long x 6.75” (17 cm) wide

• 48kW = 10.5” (27 cm) long x 6.75” (17 cm) wide

• 60kW = 6.0” (15 cm) long x 5.25” (13 cm) wide

D1 x D2 - Entrance stub-up location

• 35kW = 8.5” (22 cm) x 7.75” (20 cm)

• 48kW = 8.5” (22 cm) x 7.75” (20 cm)

• 60kW = 16.0” (41 cm) x 7.0” (18 cm)

A

B

13

A - Standby generator enclosure

B - Mounting holes in generator base

C - Fuel inlet location

D - Entrance stub-up area

D1 x D2 - Entrance stub-up location

E - Exhaust outlet area reference

F - Concrete slab reference

WARNING

Hazardous Voltage - Contact with power lines

could cause electric shock or burns, resulting

in death or serious injury.

Lifting Hazard / Heavy Object - Could result

in serious injury.

• If lifting or hoisting equipment is used, DO NOT

contact any power lines.

• DO NOT lift or move generator without assistance.

• Use lifting pipes as described below.

• DO NOT lift unit by roof as damage to generator

will occur.

Lifting the Generator

Proper tools, equipment, and qualified personnel should be

used in all phases of handling and moving the generator.

The approximate weight of the generator is listed in the

Generator Specifications Section.

Two 60” (1.5 m) lengths of 2” Schedule 40 pipe (C, below),

supplied by the installer, are required to lift the generator

onto the concrete pad. Insert the pipes through the lifting

holes (D) located in the base of the generator. (Hooks may

be used in the lifting holes in place of the pipe in accordance

with OSHA or local lifting regulations.) Use a spreader bar

to ensure that the chains, straps, or cables do not touch the

generator roof. Retouch any chipped paint with supplied

touch-up paint.

Attach the generator to the slab at the four corner locations

(B) with minimum 5/16” diameter (8mm) masonry anchor

bolts (or as required by local code) long enough to secure

the unit.

C

D

B

D

C

F

E

A

B

D2

D

D1

D

C

B

14 BRIGGSandSTRATTON.COM

Planning the Gaseous Fuel

Installation

The information provided below is intended to assist

gaseous fuel system technicians in planning installations.

State and local codes may override some of these

recommendations. Consult with the local fuel supplier or fire

marshall if clarification is needed.

WARNING

Propane

and Natural Gas are extremely

flammable and explosive, which could cause

burns, fire or explosion resulting in death or

serious injury.

• LP gas is heavier than air and will settle in low areas.

• Natural gas is lighter than air and will collect in

high areas.

• The slightest spark could ignite these fuels and cause

an explosion.

• DO NOT light a cigarette or smoke.

• A minimum of one accessible, approved manual

shutoff valve (F) shall be installed in the fuel supply

line within 6 ft (180 cm) of the generator.

• A manual fuel shut-off valve located in the interior of

the building.

• Where local conditions include earthquake,

tornado, unstable ground, or flood hazards, special

consideration shall be given to increase strength and

flexibility of piping supports and connections.

• Piping must be of the correct size to maintain the

required supply pressures and volume flow under

varying generator load conditions with all gas

appliances connected to the fuel system turned on

and operating.

• Use a pipe sealant or joint compound approved for

use with NG/LPG on all threaded fittings to reduce the

possibility of leakage.

• Installed piping must be properly purged and

leak tested, in accordance with applicable codes

and standards.

The owner and installer should consult one another to review

any changes to the installation plan that might arise when

applying the following guidelines for gaseous fuel plumbing.

• The piping material must conform to federal and local

codes, be rigidly mounted, and be protected against

vibration.

• Piping should be protected from physical damage

where it passes through flower beds, shrub beds, and

other cultivated areas where damage could occur.

• Install the supplied flexible gaseous hose (B, at right)

between the generator fuel inlet port (A) and the rigid

piping to prevent thermal expansion and contraction

from causing excessive stress on the piping material.

NOTICE

The supplied flexible gaseous pipe is not to be

installed underground or in contact with the ground. The

entire flexible gaseous pipe must be visible for periodic

inspection and must not be concealed within nor contact nor

run through any wall, floor, or partition.

• A union (C) or flanged connection shall be provided

downstream to permit removal of controls.

• A manometer test port (D) should be installed. The

port permits temporary installation of a manometer

to check whether the engine is receiving the correct

fuel pressure to operate efficiently throughout its

operating range. A digital manometer (P/N 19495) is

available at your service center. When the initial test

runs are completed, the manometer is removed and the

port is plugged.

• Where the formation of hydrates or ice is known to

occur, piping should be protected against freezing.

The termination of hard piping should include a

sediment trap (E) where condensate is not likely to

freeze.

A

B

C

D

E

F

A - Generator Fuel Inlet

B - Flexible Fuel Hose

C - Union Fitting

D - Manometer Test Port

E - Sediment Trap

F - Manual Shut-off Valve

Fuel Pipe Sizing

There are numerous on-line or printed references for fuel

pipe sizing. For example, NFPA 54 - National Fuel Gas

Code, 2006 (Item #320-6031-06) is a common resource.

The installer should consider the specific gravity of gas,

compensate for a nominal amount of restriction from

bends and fittings, and refer to federal and local codes for

guidance.

15

Fuel Conversion

The engine was set at the factory to run on natural gas (NG).

To convert the engine to run on liquid propane (LP Vapor), or

to change back to NG later, follow these steps:

1. Open the controller door.

2. Locate fuel selector switch on side of circuit breaker

enclosure.

3. Move the switch (A, below) to LP or NG.

4. Close the controller door.

Type of Fuel to Use

An important consideration affecting the entire

installation is the type of fuel to be supplied. The system

was tested and adjusted at the factory using either

natural gas or liquid propane (LP vapor). For proper

engine function, follow these guidelines:

• Use clean, dry fuel, free of moisture or any

particulate material.

• For engines running on propane (LP), use

commercial grade HD5 propane with a minimum

fuel energy of 2500 BTU/ft³ with maximum

propylene content of 5% and butane and heavier

gas content of 2.5% and minimum propane

content of 90%.

• For engines running on natural gas, power output

ratings will depend on the specific fuel but typical

derates are between 10 to 20% off the LP rating.

Using fuels outside the recommended values may

cause performance problems.

WARNING

Propane and Natural Gas are extremely

flammable and explosive, which could cause burns, fire or

explosion resulting in death or serious injury.

• The generator is equipped with an automatic safety

gas “fuel shut-off” valve.

• DO NOT operate the equipment if the “fuel shut-off”

valve is missing or inoperative.

A

Fuel Pressure

Both LP vapor and natural gas fuel supply pressure at

the generator fuel inlet port should be 7 - 11 inch WC

(17 - 28 mBar) at full load and with all gas appliances

turned on and operating. Maximum pressure drop from

static (engine not running) to full load is 0.5 inch WC

(1.3 mbar). Maximum pressure with engine OFF at no

load is 13.85 inch WC (34.5 mbar).

Power Loss

Air density is less at high altitudes, resulting in less

available engine power. Specifically, engine power will

decrease 3% for each 1,000 feet (300 m) above sea

level and 1% for each 10°F (5.6°C) above 77°F (25°C).

Generators using power management technology must

have the transfer switch programmed appropriately for

this power decrease.

Physical Properties LP Vapor Natural

Gas

Normal Atmospheric State Gas Gas

Boiling Point (in °F):

Initial

End

-44

-259

Heating Value:

BTU per gallon (Net LHV *)

BTU per gallon (gross **)

BTU per cubic feet (gas)

83,340

91,547

2,500

63,310

1,000

Density *** 36.39 57.75

Weight † 4.24 2.65

Research Octane Number

Motor Octane Number

110+

97

110+

* LHV (Low Heat Value) is the more realistic rating.

** Gross heat value does not consider heat lost in the

form of water during combustion.

*** Density is given in “Cubic Feet of Gas per Gallon of

Liquid”.

† Weight is given in “Pounds per Gallon of Liquid”.

16 BRIGGSandSTRATTON.COM

Fuel Consumption

Shown below are the estimated fuel supply

requirements at full load, 1/2-load, and exercise load for

LP Vapor and NG fuels.

Series 35000 LP Vapor Fuel Consumption

Full Load 1/2 Load Exercise

BTU/hr 399116 257844 136087

ft³/hr 160 103 54

m³/hr 4.5 2.9 1.5

Gal/hr 4.4 2.8 1.5

Series 35000 NG Fuel Consumption

Full Load 1/2 Load Exercise

BTU/hr 393844 253217 144718

ft³/hr 394 253 145

m³/hr 11.2 7.2 4.1

Series 48000 LP Vapor Fuel Consumption

Full Load 1/2 Load Exercise

BTU/hr 505670 312177 135654

ft³/hr 202 125 54

m³/hr 5.7 3.5 1.5

Gal/hr 5.5 3.4 1.5

Series 48000 NG Fuel Consumption

Full Load 1/2 Load Exercise

BTU/hr 470963 298120 151601

ft³/hr 471 298 152

m³/hr 13.3 8.4 4.3

Series 60000 LP Vapor Fuel Consumption

Full Load 1/2 Load Exercise

BTU/hr 800300 581550 247050

ft³/hr 320 233 99

m³/hr 9.1 6.6 2.8

Gal/hr 8.7 6.4 2.7

Series 60000 NG Fuel Consumption

Full Load 1/2 Load Exercise

BTU/hr 681500 512040 240840

ft³/hr 682 512 241

m³/hr 19.3 14.5 6.8

17

Power Connections

Compare this illustration with the generator to familiarize yourself with the location of these connections.

B

C

A

A - Power Connection - Power connection to transfer

switch.

B - Neutral Connection - Connect to transfer switch neutral.

C - Ground Connection - Connect to transfer switch

ground.

Ground the generator per applicable codes, standards, and

regulations. There are two generator GND lug locations.

The location shown by (C, above) should suffice for most

applications. The second generator GND lug is located

on the frame below the generator circuit breaker cover.

This should ONLY be used for a ground rod located at the

generator, if required by local codes.

For system connections such as remote start, e-stops,

and controller inputs and outputs, refer to the connection

diagrams on the following pages.

• For power output connection, use 300 volt, 167

-194°F (75-90°C) wire. See chart for proper wire size.

• For utility circuit connection, use #14 AWG minimum

300 volt, 167-194°F (75-90°C) wire.

• For transfer switch communication, use #18 AWG

twisted pair conductors, no greater than 200 ft (60 m)

in length, 300 volt, 167-194°F (75-90°C) wire.

Series 35000 Voltage Rated Amps Wire Size

1-Phase 120/240 145 2/0

3-Phase Wye 120/208 121 1/0

3-Phase Delta 120/240 105 1 AWG

3-Phase Wye 240/416 61 4 AWG

3-Phase Wye 277/480 53 6 AWG

3-Phase Wye 347/600 42 8 AWG

Series 48000 Voltage Rated Amps Wire Size

1-Phase 120/240 200 4/0

3-Phase Wye 120/208 167 3/0

3-Phase Delta 120/240 144 2/0

3-Phase Wye 240/416 83 3 AWG

3-Phase Wye 277/480 72 4 AWG

3-Phase Wye 347/600 58 4 AWG

Series 60000 Voltage Rated Amps Wire Size

1-Phase 120/240 250 300 kcmil

3-Phase Wye 120/208 215 250 kcmil

3-Phase Delta 120/240 186 4/0

3-Phase Wye 240/416 108 1 AWG

3-Phase Wye 277/480 93 2 AWG

3-Phase Wye 347/600 75 4 AWG

Refer to the Data Tag to determine the series of generator.

A

18 BRIGGSandSTRATTON.COM

19

20 BRIGGSandSTRATTON.COM

La page charge ...

Simplicity 076451-01 Manuel utilisateur

Simplicity 076451-01 Manuel utilisateur

dans d''autres langues

Documents connexes