Simplicity 020581-01 Manuel utilisateur
- Catégorie
- Nettoyeurs haute pression
- Taper
- Manuel utilisateur
Ce manuel convient également à
Not for
Reproduction
BRIGGS & STRATTON CORPORATION
MILWAUKEE, WISCONSIN, U.S.A.
Manual No. 80008651 Revision C
Pressure Washer
Operator’s Manual
This pressure washer is rated in accordance to the Pressure Washer Manufacturers Association (PWMA)
standard PW101-2010 (Testing and Rating Performance of Pressure Washers).
Not for
Reproduction
2 BRIGGSandSTRATTON.COM
Thank you for purchasing this quality-built Briggs & Stratton® pressure washer. We are pleased that you’ve
placed your confidence in the Briggs & Stratton brand. When operated and maintained according to the
instructions in this manual, your Briggs & Stratton pressure washer will provide many years of dependable service.
This manual contains safety information to make you aware of the hazards and risks associated with pressure
washers and how to avoid them. Because Briggs & Stratton does not necessarily know all the applications this
pressure washer could be used for, it is important that you read and understand these instructions thoroughly
before attempting to start or operate this equipment. Save these original instructions for future reference.
This pressure washer requires final assembly before use. Refer to the Assembly section of this manual for
instructions on final assembly procedures. Follow the instructions completely.
Where to Find Us
You never have to look far to find Briggs & Stratton support and service for your pressure washer. Consult your
Yellow Pages. There are over 30,000 Briggs & Stratton authorized service dealers worldwide who provide quality
service. You can also contact Briggs & Stratton Customer Service by phone at (800) 743-4115, or on the Internet
at BRIGGSandSTRATTON.COM.
Pressure Washer Engine
Model Number _____________________ Model Number ______________________
Revision __________________________ Type Number _______________________
Serial Number ______________________ Code Number _______________________
Date Purchased ___________________
Table of Contents
Operator Safety....................... 3
Assembly............................ 6
Features and Controls ................ 10
Operation........................... 11
Maintenance ........................ 15
Troubleshooting ..................... 21
Warranty ........................... 22
Product Specifications ................ 24
Common Service Parts ............... 24
Copyright © 2017. Briggs & Stratton Corporation
Milwaukee, WI, USA. All rights reserved.
Not for
Reproduction
3
Operator Safety
Equipment Description
Read this manual carefully and become
familiar with your pressure washer. Know
its applications, its limitations, and any
hazards involved.
This pressure washer operates at 2,200 PSI
(151.6 BAR) at a flow rate of 1.9 gallons (7.2 l) per
minute. This high quality residential system features
10” (25.4 cm) wheels, axial cam pump with stainless
steel pistons, automatic cool down system, detergent
siphoning system, nozzle extension with quick
connect, quick connect spray tips, heavy duty
25’ (7.6 m) hose, and more.
Every effort has been made to ensure that information
in this manual is accurate and current. However, we
reserve the right to change, alter, or otherwise improve
the product and this document at any time without prior
notice.
The Emission Control System for this pressure washer
is warranted for standards set by the Environmental
Protection Agency and the California Air Resources
Board.
This spark ignition system complies with the Canadian
standard ICES-002.
Important Safety Information
Safety Symbols and Meanings
The safety alert symbol indicates a potential
personal injury hazard. A signal word (DANGER,
WARNING, or CAUTION) is used with the alert symbol
to designate a degree or level of hazard seriousness.
A safety symbol may be used to represent the type of
hazard. The signal word NOTICE is used to address
practices not related to personal injury.
DANGER indicates a hazard which, if not avoided,
will result in death or serious injury.
WARNING indicates a hazard which, if not
avoided, could result in death or serious injury.
CAUTION indicates a hazard which, if not
avoided, could result in minor or moderate injury.
NOTICE address practices not related to personal
injury.
Fire
Explosion
Toxic Fumes
Hot Surface
Moving
Parts
Electrical Shock
Slippery
Surface
Fall
Kickback
Flying
Objects
Fluid Injection
Operator’s
Manual
Chemical
Burn
Projectile
WARNING POISONOUS GAS HAZARD.
Engine exhaust contains carbon monoxide,
a poisonous gas that could kill you in
minutes. You CANNOT smell it, see it, or
taste it. Even if you do not smell exhaust fumes, you
could still be exposed to carbon monoxide gas.
Some chemicals or detergents could be harmful if
inhaled or ingested, resulting in death, serious
injury, nausea, fainting or poisoning.
• Operate this product ONLY outside far away from
windows, doors and vents to reduce the risk of carbon
monoxide gas from accumulating and potentially being
drawn towards occupied spaces.
• Install battery-operated carbon monoxide alarms or
plug-in carbon monoxide alarms with battery back-up
according to the manufacturer’s instructions. Smoke
alarms cannot detect carbon monoxide gas.
• DO NOT run this product inside homes, garages,
basements, crawlspaces, sheds, or other partially-
enclosed spaces even if using fans or opening doors
and windows for ventilation. Carbon monoxide can
quickly build up in these spaces and can linger for hours,
even after this product has shut off.
• ALWAYS place this product downwind and point the
engine exhaust away from occupied spaces.
If you start to feel sick, dizzy, or weak while using this
product, get to fresh air RIGHT AWAY. See a doctor. You
may have carbon monoxide poisoning.
• Use a respirator or mask whenever there is a chance that
vapors may be inhaled when using chemicals.
• Read all instructions with mask so you are certain the
mask will provide the necessary protection against
inhaling harmful vapors when using chemicals.
Not for
Reproduction
4 BRIGGSandSTRATTON.COM
WARNING The engine exhaust from this
product contains chemicals known to the State of
California to cause cancer, birth defects, or other
reproductive harm.
WARNING This product contains lead and lead
compounds, known to the State of California to
cause birth defects or other reproductive harm.
Wash your hands after handling this product.
WARNING Fuel and its vapors are extremely
flammable and explosive which could
cause burns, fire or explosion
resulting in death or serious injury.
WHEN ADDING OR DRAINING FUEL
• Turn pressure washer engine OFF and let it cool at least
2 minutes before removing fuel cap. Loosen cap slowly to
relieve pressure in tank.
• Fill or drain fuel tank outdoors.
• DO NOT overfill tank. Allow space for fuel expansion.
• If fuel spills, wait until it evaporates before starting engine.
• Keep fuel away from sparks, open flames, pilot lights,
heat, and other ignition sources.
• Check fuel lines, tank, cap and fittings frequently for
cracks or leaks. Replace if necessary.
• DO NOT light a cigarette or smoke.
WHEN STARTING EQUIPMENT
• Ensure spark plug, muffler, fuel cap, and air cleaner are in
place.
• DO NOT crank engine with spark plug removed.
WHEN OPERATING EQUIPMENT
• DO NOT operate this product inside any building,
carport, porch, mobile equipment, marine applications, or
enclosure.
• DO NOT tip engine or equipment at angle which causes
fuel to spill.
• DO NOT spray flammable liquids.
WHEN TRANSPORTING, MOVING OR REPAIRING
EQUIPMENT
• Transport/move/repair with fuel tank EMPTY or with fuel
shutoff valve OFF (0).
• DO NOT tip engine or equipment at angle which causes
fuel to spill.
• Disconnect spark plug wire.
WHEN STORING FUEL OR EQUIPMENT WITH FUEL
IN TANK
• Store away from furnaces, stoves, water heaters, clothes
dryers, or other appliances that have pilot light or other
ignition source because they could ignite fuel vapors.
WARNING Risk of electrocution.
Contact with power source could cause
electric shock or burn resulting in death or
serious injury.
• NEVER spray near power source.
WARNING Use of pressure washer could create
puddles and slippery surfaces
causing you to fall resulting in death
or serious injury.
Kickback from spray gun could cause you to fall
resulting in death or serious injury.
• Operate pressure washer from a stable surface.
• The cleaning area should have adequate slopes and
drainage to reduce the possibility of a fall due to slippery
surfaces.
• Be extremely careful if you must use the pressure washer
from a ladder, scaffolding, or any other similar location.
• Firmly grasp spray gun with both hands when using high
pressure spray to avoid injury when spray gun kicks
back.
WARNING Starter cord kickback (rapid
retraction) will pull hand and arm toward
engine faster than you can let go which
could cause broken bones, fractures,
bruises, or sprains resulting in serious injury.
• NEVER pull starter cord without first relieving spray gun
pressure.
• When starting engine, pull cord slowly until resistance is
felt and then pull rapidly to avoid kickback.
• After each starting attempt, where engine fails to run,
always point spray gun in safe direction, press red button
and squeeze spray gun trigger to release high pressure.
• Firmly grasp spray gun with both hands when using high
pressure spray to avoid injury when spray gun kicks
back.
WARNING Exhaust heat/gases could ignite
combustibles, structures or damage
fuel tank causing a fire, resulting in
death or serious injury.
Contact with muffler area could cause burns
resulting in serious injury.
• DO NOT touch hot parts and AVOID hot exhaust gases.
• Allow equipment to cool before touching.
• Keep at least 5 ft. (1.5 m) of clearance on all sides of
pressure washer including overhead.
• It is a violation of California Public Resource Code,
Section 4442, to use or operate the engine on any forest-
covered, brush-covered, or grass-covered land unless
the exhaust system is equipped with a spark arrester, as
defined in Section 4442, maintained in effective working
order. Other states or federal jurisdictions may have
similar laws.
Contact the original equipment manufacturer, retailer,
or dealer to obtain a spark arrester designed for the
exhaust system installed on this engine.
• Replacement parts must be the same and installed in the
same position as the original parts.
Not for
Reproduction
5
NOTICE High pressure spray could damage fragile
items including glass.
• DO NOT point spray gun at glass when using red (0°) spray
tip.
• NEVER aim spray gun at plants.
NOTICE Improper treatment of pressure washer
could damage it and shorten its life.
• If you have questions about intended use, ask dealer or
contact qualified service center.
• NEVER operate units with broken or missing parts, or
without protective housing or covers.
• DO NOT by-pass any safety device on this machine.
• DO NOT tamper with governed speed.
• DO NOT operate pressure washer above rated pressure.
• DO NOT modify pressure washer in any way.
• Before starting pressure washer in cold weather, check all
parts of the equipment to be sure ice has not formed there.
• NEVER move machine by pulling on hoses. Use handle
provided on unit.
• This equipment is designed to be used with Briggs &
Stratton authorized parts ONLY. If equipment is used with
parts that DO NOT comply with minimum specifications,
user assumes all risks and liabilities.
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected, which
could result in serious injury.
• If cut by fluid, call physician immediately. DO NOT treat
as a simple cut.
• DO NOT allow CHILDREN to operate pressure washer.
• NEVER repair high pressure hose. Replace it.
• NEVER repair leaking connections with sealant of any
kind. Replace o-ring or seal.
• NEVER connect high pressure hose to nozzle extension.
• Keep high pressure hose connected to pump and spray
gun while system is pressurized.
• ALWAYS point spray gun in safe direction, press red
button and squeeze spray gun trigger to release high
pressure, every time you stop engine.
• NEVER aim spray gun at people, animals, or plants.
• DO NOT secure spray gun in open position.
• DO NOT leave spray gun unattended while machine is
running.
• NEVER use a spray gun which does not have a trigger
lock or trigger guard in place and in working order.
• Always be certain spray gun, nozzles and accessories
are correctly attached.
WARNING Unintentional sparking could cause
fire or electric shock resulting in
death or serious injury.
WHEN ADJUSTING OR MAKING REPAIRS TO YOUR
PRESSURE WASHER
• Disconnect the spark plug wire from the spark plug and
place the wire where it cannot contact spark plug.
WHEN TESTING FOR ENGINE SPARK
• Use approved spark plug tester.
• DO NOT check for spark with spark plug removed.
WARNING Starter and other rotating parts
could entangle hands, hair, clothing, or
accessories resulting in serious injury.
• NEVER operate pressure washer without protective
housing or covers.
• DO NOT wear loose clothing, jewelry or anything that
could be caught in the starter or other rotating parts.
• Tie up long hair and remove jewelry.
CAUTION
Excessively high operating speeds
could result in minor injury.
Excessively low operating speeds impose a heavy
load.
• DO NOT tamper with governor spring, links or other
parts to increase engine speed. Pressure washer
supplies correct rated pressure and flow when running at
governed speed.
• DO NOT modify pressure washer in any way.
WARNING Risk of eye or bodily injury.
Spray could splash back or propel
objects resulting in serious injury.
• Always wear indirect vented (chemical splash) safety
goggles marked to comply with ANSI Z87.1 when using
or in vicinity of this equipment.
• NEVER substitute safety glasses or dry-condition
goggles for indirect vented safety goggles.
• Always wear protective clothing such as a long-sleeved
shirt, long pants and close-toed shoes.
• NEVER operate pressure washer when barefoot or
wearing sandals or shorts.
WARNING Chemical Burn Hazard.
Chemicals could cause burns resulting in
death or serious injury.
• DO NOT use caustic liquid with pressure washer.
• Use ONLY pressure washer safe detergents/soaps.
Follow all manufacturers instructions.
Not for
Reproduction
6 BRIGGSandSTRATTON.COM
Assembly
Read entire operator’s manual before you
attempt to assemble or operate your new
pressure washer.
Your pressure washer requires some assembly and is
ready for use after it has been properly serviced with
the recommended oil and fuel.
If you have any problems with the assembly of your
pressure washer, please call the pressure washer
helpline at (800) 743-4115. If calling for assistance,
please have the model, revision, and serial number
from the identification label available.
Unpack Pressure Washer
1. Remove the parts bag, accessories, and inserts
included with pressure washer.
2. Open carton completely by cutting each corner
from top to bottom.
3. Ensure you have all included items prior to
assembly.
Items in the carton include:
• Main Unit
• Handle
• High Pressure Hose
• Spray Gun
• Nozzle Extension with Quick Connect
• Accessory Tray
• Oil Pouch
• Parts Bag (which includes the following):
• Operator’s Manual
• Owner’s Registration Card
• Ba g containing 3 Multi–Colored Spray Tips
• Handle Fastening Hardware Kit (which
includes):
• Carriage Bolts (2)
• Plastic Knobs (2)
• Tree Clips (4)
To prepare your pressure washer for operation,
you will need to perform these tasks:
1. Fill out and send in registration card.
2. Attach handle and accessory tray to main unit.
3. Add oil to engine crankcase.
4. Add fuel to fuel tank.
5. Connect high pressure hose to spray gun and
pump.
6. Connect water supply to pump.
7. Attach nozzle extension to spray gun.
8. Select/attach quick connect spray tip to nozzle
extension.
Attach Handle and Accessory Tray
1. Place handle (A) onto handle supports (B)
connected to main unit. Make sure holes (C) in
handle align with holes (C) on handle supports.
NOTICE It may be necessary to move the handle
supports from side to side in order to align the handle
so it will slide over the handle supports.
2. Insert carriage bolts (D) through holes from back
of unit and attach a plastic knob (E) from front of
unit. Tighten by hand.
3. Place accessory tray (F) over holes (G) on handle
(viewing from front of unit). Push the tree clips (H)
into the holes until they sit flat against the accessory
tray.
4. Insert multi–colored spray tips and other supplied
accessories in spaces provided in accessory tray.
See How to Use Accessory Tray.
D
E
F
H
G
B
A
C
C
Not for
Reproduction
7
Add Engine Oil
1. Place pressure washer on a flat, level surface.
2. Clean area around oil fill and remove yellow oil fill
cap/dipstick.
3. Hold neck of supplied oil pouch and remove cap.
4. Slowly pour contents of oil pouch into oil fill
opening. Checking oil level frequently, fill to FULL
mark (top hole) on dipstick.
NOTICE Pause to permit oil to settle. Wipe dipstick
clean each time oil level is checked. DO NOT overfill.
NOTICE Improper treatment of pressure washer
could damage it and shorten its life.
• DO NOT attempt to crank or start the engine before it has
been properly serviced with the recommended oil. This
could result in an engine failure.
5. Replace oil fill cap/dipstick and fully tighten.
Add Fuel
Fuel must meet these requirements:
• Clean, fresh, unleaded gasoline.
• A minimum of 87 octane/87 AKI (91 RON). For
high altitude use, see High Altitude.
• Gasoline with up to 10% ethanol (gasohol) is
acceptable.
NOTICE Use of unapproved fuels could damage
generator and voids warranty.
• DO NOT use unapproved gasoline such as E15 and E85.
• DO NOT mix oil in gasoline or modify engine to run on
alternate fuels.
To protect the fuel system from gum formation, mix in a
fuel stabilizer when adding fuel. See Storage. All fuel is
not the same. If you experience starting or performance
problems after using fuel, switch to a different fuel
provider or change brands. This engine is certified to
operate on gasoline. The emission control system for this
engine is EM (Engine Modifications).
1. Clean area around fuel fill cap, remove cap.
2. Slowly add regular unleaded fuel (A) to fuel tank
(B). Be careful not to overfill. To allow for fuel
expansion, do not fill above the bottom of the fuel
tank neck.
3. Install fuel cap and let any spilled fuel evaporate
before starting engine.
Full
Add
WARNING Fuel and its vapors are extremely
flammable and explosive which could
cause burns, fire or explosion
resulting in death or serious injury.
WHEN ADDING FUEL
• Turn pressure washer engine OFF and let it cool at least
2 minutes before removing fuel cap. Loosen cap slowly to
relieve pressure in tank.
• Fill fuel tank outdoors.
• DO NOT overfill tank. Allow space for fuel expansion.
• If fuel spills, wait until it evaporates before starting engine.
• Keep fuel away from sparks, open flames, pilot lights,
heat, and other ignition sources.
• Check fuel lines, tank, cap and fittings frequently for
cracks or leaks. Replace if necessary.
• DO NOT light a cigarette or smoke.
B
A
Not for
Reproduction
8 BRIGGSandSTRATTON.COM
High Altitude
At altitudes over 5,000 ft. (1524 m), a minimum
85 octane/85 AKI (89 RON) gasoline is acceptable. To
remain emissions compliant, high altitude adjustment is
required. Operation without this adjustment will cause
decreased performance, increased fuel consumption,
and increased emissions. See an Authorized Briggs &
Stratton dealer for high altitude adjustment information.
Operation of the engine at altitudes below 2,500 ft.
(762 m) with the high altitude kit is not recommended.
Lubricate O-Rings
Lubrication of o-rings is extremely important for
installation and operation. The use of a lubricant
(petroleum or synthetic grease) during assembly helps
seat o-rings properly and provides an improved seal. It
also helps protect the o-ring from damage by abrasion,
pinching or cutting and extends the life of the o-ring.
NOTICE ALWAYS apply a small amount of lubricant
on o-rings prior to assembling the garden hose to the
pump (A), high pressure hose (B), spray gun (C), and
nozzle extension (D).
Lubricate all connections shown below, following
these instructions:
1. Inspect and clean connecting surfaces prior to
lubrication and assembly.
2. Use lubricants sparingly during assembly; a light
film is all that is required.
3. Use a small brush or cotton swab to apply grease
directly to o-rings where they are not accessible
(QC fitting, M22 fitting).
D
C
A
B
Not for
Reproduction
9
Connect Hose and Water Supply to Pump
NOTICE DO NOT run the pump without the water
supply connected and turned on.
• Damage to equipment resulting from failure to follow this
instruction will void warranty.
NOTICE Remove and discard the shipping caps from
the pump’s high pressure outlet and water inlet before
attaching hoses.
1. Uncoil high pressure hose and attach one end of
hose to base of spray gun. Tighten by hand.
2. Attach other end of high pressure hose to high
pressure outlet on pump. Tighten by hand.
3. Before connecting garden hose to water inlet,
inspect inlet screen (A). Clean screen if it contains
debris or have it replaced if damaged. DO NOT
run pressure washer if inlet screen is damaged.
4. Run water through your garden hose for
30 seconds to clean out any debris.
NOTICE DO NOT siphon standing water for the water
supply. Use ONLY cold water (less than 100°F).
NOTICE Using a One Way Valve (vacuum breaker
or check valve) at pump inlet could cause pump or
inlet connector damage.
• There MUST be at least 10 ft. (3 m) of unrestricted garden
hose between the pressure washer inlet and any device,
such as a vacuum breaker or check valve.
• Damage to equipment resulting from failure to follow this
instruction will void warranty.
5. Connect the garden hose (not to exceed 50 ft.
(15 m) in length) to the water inlet. Tighten by
hand.
6. Turn ON the water, press red button (B) on the
gun and squeeze the trigger to purge the pump
system of air and impurities.
Checklist Before Starting Engine
Review the unit’s assembly to ensure you have
performed all of the following:
1. Be sure to read the Operator Safety and
Operation before using pressure washer.
2. Make sure handle is in place and secure.
3. Check that oil has been added to proper level in
the engine crankcase.
4. Add proper fuel to fuel tank.
5. Check for properly tightened hose connections.
6. Check to make sure there are no kinks, cuts, or
damage to high pressure hose.
7. Provide a proper water supply at an adequate
flow.
B
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
• NEVER connect high pressure hose to nozzle extension.
• Keep high pressure hose connected to pump and spray
gun while system is pressurized.
• Always be certain spray gun, nozzles and accessories
are correctly attached.
WARNING Risk of eye injury.
Spray could splash back or propel objects
resulting in serious injury.
• Always wear indirect vented (chemical splash) safety
goggles marked to comply with ANSI Z87.1 when using
or in vicinity of this equipment.
• NEVER substitute safety glasses or dry-condition
goggles for indirect vented safety goggles.
A
Not for
Reproduction
10 BRIGGSandSTRATTON.COM
Features and Controls
Read this Operator’s Manual and safety rules before operating your pressure washer.
Compare the illustrations with your pressure washer, to familiarize yourself with the locations of various
controls and adjustments. Save this manual for future reference.
A - Spray Gun — Controls the application of water
onto cleaning surface with trigger device. Includes
trigger lock.
B - Nozzle Extension with Quick Connect — Allows
you to switch between three different spray tips.
C - Recoil Starter — Used for starting the engine
manually.
D - Oil Fill/Dipstick — Check, add and drain engine
oil here.
E - Warning/Operating Instructions Tag — Identifies
hazards and proper procedure to start/stop pressure
washer.
F - Water Inlet — Connection for garden hose.
G - Pump — Develops high pressure.
H - Automatic Cool Down System — Cycles water
through pump when water reaches 125°-155°F.
(52°-68°C). Warm water will discharge from pump
onto ground. This system prevents internal pump
damage.
J - Detergent Siphoning Tube — Use to siphon
pressure washer safe detergents into the low
pressure stream.
K - Air Filter — Protects engine by filtering dust and
debris out of intake air.
L - Primer Bulb — Prepares a cold engine for starting.
M - Engine Stop Switch — Push this switch to ON (I)
position before using recoil starter. Push switch to
OFF (0) position for shutting off engine.
N - Fuel Tank — Fill tank with regular unleaded fuel.
Always leave room for fuel expansion.
P - High Pressure Hose — Connect one end to water
pump and the other end to spray gun.
R - Accessory Tray — Provides convenient storage
for standard and optional accessories, such as
brushes, turbo wands, etc.
S - Spray Tips — Detergent, 0° and 25°: for various
high pressure cleaning applications.
Items Not Shown:
Identification Label (near rear of base plate) —
Provides model and serial number of pressure washer.
Please have these readily available if calling for
assistance.
High Pressure Outlet — Connection for high
pressure hose.
Engine Identification — Provides model, type and
code of engine. Please have these readily available if
calling for assistance.
E
A
H
,
G
F
R
S
B
C
P
N
J
K
L
D
M
Not for
Reproduction
11
Operation
If you have any problems operating your pressure
washer, please call the pressure washer helpline at
(800) 743-4115.
Pressure Washer Location
Carbon Monoxide Poisoning
Risk of Fire Clearances
How to Start Your Pressure Washer
To start your pressure washer for the first time,
follow these instructions step-by-step. This starting
information also applies if you have let the pressure
washer sit idle for at least a day.
1. Place pressure washer near an outside water
source capable of supplying water at a flow rate
greater than 2.9 gallons (10.9 liters) per minute
and no less than 20 PSI (1.4 BAR) at pressure
washer end of garden hose. DO NOT siphon
supply water.
2. Check that high pressure hose is tightly
connected to spray gun and pump. See Assembly
section.
3. Make sure unit is in a level position.
4. Connect garden hose to water inlet on pressure
washer pump.
NOTICE DO NOT run the pump without the water
supply connected and turned on.
• Damage to equipment resulting from failure to follow this
instruction will void warranty.
5. Turn ON the water, press red button on the gun
and squeeze the trigger to purge the pump system
of air and impurities.
6. Attach nozzle extension to spray gun. Tighten by
hand.
7. Choose spray tip you want to use, pull back on
collar of nozzle extension, insert spray tip and
release collar. Tug on spray tip to make sure it is
securely in place. See How to Use Spray Tips.
8. Push engine stop switch (A) to ON (I) position.
9. Press primer bulb (B) firmly 3 times. For a warm
engine, DO NOT press primer bulb.
NOTICE Before starting the pressure washer, be sure
you are wearing safety goggles as described below.
WARNING Exhaust heat/gases could ignite
combustibles, structures or damage fuel tank
causing a fire, resulting in death or serious
injury.
• Keep at least 5 ft. (1.5 m) clearance on all sides of
pressure washer including overhead.
WARNING POISONOUS GAS HAZARD.
Engine exhaust contains carbon monoxide,
a poisonous gas that could kill you in
minutes. You CANNOT smell it, see it, or
taste it. Even if you do not smell exhaust fumes, you
could still be exposed to carbon monoxide gas.
• Operate this product ONLY outside far away from
windows, doors and vents to reduce the risk of carbon
monoxide gas from accumulating and potentially being
drawn towards occupied spaces.
• Install battery-operated carbon monoxide alarms or
plug-in carbon monoxide alarms with battery back-up
according to the manufacturer’s instructions. Smoke
alarms cannot detect carbon monoxide gas.
• DO NOT run this product inside homes, garages,
basements, crawlspaces, sheds, or other partially-
enclosed spaces even if using fans or opening doors
and windows for ventilation. Carbon monoxide can
quickly build up in these spaces and can linger for hours,
even after this product has shut off.
• ALWAYS place this product downwind and point the
engine exhaust away from occupied spaces.
If you start to feel sick, dizzy, or weak while using this
product, get to fresh air RIGHT AWAY. See a doctor. You
may have carbon monoxide poisoning.
Exhaust port
pointed away from
occupied spaces
A
B
Not for
Reproduction
12 BRIGGSandSTRATTON.COM
10. When starting engine, position yourself as
recommended below and grasp starter grip
handle and pull slowly until you feel some
resistance. Then pull rapidly to start engine.
11. Return starter grip handle slowly. DO NOT let
rope “snap back” against starter.
How to Stop Your Pressure Washer
1. Release spray gun trigger and let engine idle for
two minutes.
2. Push engine stop switch to OFF (0) position.
3. ALWAYS point gun in a safe direction and press
red button and squeeze spray gun trigger to
release retained high water pressure.
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected, which
could result in serious injury.
• DO NOT allow CHILDREN to operate pressure washer.
• Keep high pressure hose connected to pump and spray
gun while system is pressurized.
• NEVER aim spray gun at people, animals, or plants.
• DO NOT secure spray gun in open position.
• DO NOT leave spray gun unattended while machine is
running.
• NEVER use a spray gun which does not have a trigger
lock or trigger guard in place and in working order.
• Always be certain spray gun, nozzles and accessories
are correctly attached.
WARNING Exhaust heat/gases could ignite
combustibles, structures or damage
fuel tank causing a fire, resulting in
death or serious injury.
Contact with muffler area could cause burns
resulting in serious injury.
• DO NOT touch hot parts and AVOID hot exhaust gases.
• Allow equipment to cool before touching.
• Keep at least 5 ft. (1.5 m) of clearance on all sides of
pressure washer including overhead.
• It is a violation of California Public Resource Code,
Section 4442, to use or operate the engine on any forest-
covered, brush-covered, or grass-covered land unless
the exhaust system is equipped with a spark arrester, as
defined in Section 4442, maintained in effective working
order. Other states or federal jurisdictions may have
similar laws.
Contact the original equipment manufacturer, retailer,
or dealer to obtain a spark arrester designed for the
exhaust system installed on this engine.
• Replacement parts must be the same and installed in the
same position as the original parts.
WARNING Starter cord kickback (rapid
retraction) will pull hand and arm toward
engine faster than you can let go which
could cause broken bones, fractures,
bruises, or sprains resulting in serious injury.
• NEVER pull starter cord without first relieving spray gun
pressure.
• When starting engine, pull cord slowly until resistance is
felt and then pull rapidly to avoid kickback.
• After each starting attempt, where engine fails to run,
always point spray gun in safe direction, press red button
and squeeze spray gun trigger to release high pressure.
• Firmly grasp spray gun with both hands when using high
pressure spray to avoid injury when spray gun kicks
back.
WARNING Risk of eye injury.
Spray could splash back or propel objects
resulting in serious injury.
• Always wear indirect vented (chemical splash) safety
goggles marked to comply with ANSI Z87.1 when using
or in vicinity of this equipment.
• NEVER substitute safety glasses or dry-condition
goggles for indirect vented safety goggles.
Not for
Reproduction
13
How to Use Accessory Tray
The unit is equipped with an accessory tray with places
to store your spray gun, nozzle extension and spray
tips. There is also a hook at the front of the accessory
tray to hold your high pressure hose.
NOTICE The extra hole in the tray is for storing a utility
brush. The extra clip in the tray is for storing a turbo
nozzle. The brush and turbo nozzle are NOT included
with your pressure washer. You can buy these items as
optional accessories.
1. Place nozzle extension through hole on accessory
tray, as shown.
2. Place spray gun through hole on accessory tray
on right side of unit.
3. Insert multi–colored spray tips in spaces provided
in accessory tray.
4. Hang high pressure hose on hook attached to
accessory tray on front of tray, as shown.
How to Use Spray Tips
The quick–connect on the nozzle extension allows you
to switch between three different quick connect spray
tips. Spray tips can be changed while pressure washer
is running once spray gun trigger lock is engaged. The
spray tips vary the spray pattern as shown.
Follow these instructions to change spray tips:
1. Pull back collar on quick–connect and pull current
spray tip off. Store spray tips in holes provided on
the accessory tray.
2. Select desired spray tip:
• For gentle rinse, select green 25° spray tip.
• To scour surface, select red 0° spray tip.
• To apply detergent, select black spray tip.
3. Pull back on collar, insert new spray tip and
release collar. Tug on spray tip to make sure it is
securely in place.
Usage Tips
• For most effective cleaning, keep spray tip from
8 to 24 inches away from cleaning surface.
• If you get spray tip too close, especially using a
high pressure spray tip, you may damage surface
being cleaned.
• DO NOT get closer than 6 inches when cleaning
tires.
Black
Use to apply
detergent
25° Green 0° Red
Low Pressure
High Pressure
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
• NEVER exchange spray tips without the trigger lock
being engaged on the spray gun.
• DO NOT twist spray tips while spraying.
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected, which
could result in serious injury.
• Keep high pressure hose connected to pump and spray
gun while system is pressurized.
• ALWAYS point spray gun in safe direction, press red
button and squeeze spray gun trigger to release high
pressure, every time you stop engine.
Not for
Reproduction
14 BRIGGSandSTRATTON.COM
Applying Detergent
To apply detergent, follow these steps:
1. Review use of spray tips.
2. Prepare detergent solution as required by job.
3. Place end of detergent siphoning tube into
detergent container.
NOTICE Make sure end of tube is fully submerged in
detergent while applying detergent.
NOTICE Contact with hot muffler could damage
detergent siphoning tube.
• When inserting tube into a detergent solution bottle, route
tube so as to keep it from inadvertently contacting the hot
muffler.
4. Make sure black spray tip is installed.
NOTICE Detergent cannot be applied with the high
pressure spray tips (Green or Red).
5. Make sure garden hose is connected to water
inlet. Check that high pressure hose is connected
to spray gun and pump. Turn on water.
NOTICE You must attach all hoses before you start
the engine.
• Starting the engine without all the hoses connected and
without the water turned ON could damage the pump.
• Damage to equipment resulting from failure to follow this
instruction will void warranty.
6. Start engine following instructions How to Start
Your Pressure Washer.
7. Apply detergent to a dry surface, starting at lower
portion of area to be washed and work upward,
using long, even, overlapping strokes.
8. Allow detergent to “soak in” for 3-5 minutes
before washing and rinsing. Reapply as needed
to prevent surface from drying. DO NOT allow
detergent to dry on (prevents streaking).
NOTICE You must flush the detergent siphoning
system after each use by placing end of tube into a
bucket of clean water, then run the pressure washer in
low pressure for 1-2 minutes.
Pressure Washer Rinsing
For Rinsing:
1. Remove black spray tip from nozzle extension.
2. Select and install desired high pressure spray tip
following instructions How to Use Spray Tips.
3. Keep spray gun a safe distance from area you
plan to spray.
4. Apply a high pressure spray to a small area and
then check surface for damage. If no damage
is found, you can assume it is okay to continue
rinsing.
5. Start at top of area to be rinsed, working down with
same overlapping strokes as you used for cleaning.
Cleaning Detergent Siphoning Tube
If you used the detergent siphoning tube, you must
flush it with clean water before stopping the engine.
1. Place detergent siphoning tube in a bucket full of
clean water.
2. Remove high pressure spray tip from nozzle
extension.
3. Select and install black detergent spray tip
following instructions How to Use Spray Tips.
4. Flush for 1-2 minutes.
5. Shut OFF engine following instructions How to
Stop Pressure Washer and turn off water supply.
6. ALWAYS point spray gun in a safe direction and
squeeze spray gun trigger to release retained high
water pressure.
Automatic Cool Down System (Thermal
Relief)
If you run the engine on your pressure washer for
3-5 minutes without pressing the trigger on the
spray gun, circulating water in the pump can reach
temperatures above 125°-155°F. (52°-68°C). The
system engages to cool the pump by discharging the
warm water onto the ground.
WARNING Kickback from spray gun could
cause you to fall resulting in death or
serious injury.
• Operate pressure washer from a stable surface.
• Be extremely careful if you must use the pressure washer
from a ladder, scaffolding, or any other similar location.
• Firmly grasp spray gun with both hands when using high
pressure spray to avoid injury when spray gun kicks
back.
WARNING Chemical Burn Hazard.
Chemicals could cause burns resulting in
death or serious injury.
• DO NOT use caustic liquid with pressure washer.
• Use ONLY pressure washer safe detergents/soaps.
Follow all manufacturers instructions.
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected, which
could result in serious injury.
• Keep high pressure hose connected to pump and spray
gun while system is pressurized.
• ALWAYS point spray gun in safe direction, press red
button and squeeze spray gun trigger to release high
pressure, every time you stop engine.
Not for
Reproduction
15
Maintenance
Maintenance Schedule
Follow the hourly or calendar intervals, whichever
occurs first. More frequent service is required when
operating in adverse conditions noted below.
1
Clean if clogged. Replace if perforated or torn.
2
Service more often under dirty or dusty conditions.
General Recommendations
Regular maintenance will improve the performance
and extend the life of the pressure washer. See any
qualified dealer for service.
The pressure washer’s warranty does not cover
items that have been subjected to operator abuse or
negligence. To receive full value from the warranty,
the operator must maintain the pressure washer as
instructed in this manual, including proper storage as
detailed in Winter Storage and Long Term Storage.
NOTICE Should you have questions about replacing
components on your pressure washer, please call
(800) 743-4115 for assistance.
Some adjustments will need to be made periodically to
properly maintain your pressure washer.
All service and adjustments should be made at least
once each season. A new spark plug and clean
air filter assure proper fuel-air mixture and help
your engine run better and last longer. Follow the
requirements in the Maintenance Schedule chart
above.
Pump Oil
DO NOT attempt any oil maintenance on this pump.
The pump is pre-lubricated and sealed from the
factory, requiring no additional maintenance for the life
of the pump.
Emissions Control
Maintenance, replacement, or repair of the
emissions control devices and systems may
be performed by any non-road engine repair
establishment or individual. However, to obtain
“no charge” emissions control service, the work must
be performed by a factory authorized dealer. See the
Emissions Warranty.
Before Each Use
1. Check engine oil level.
2. Clean debris.
3. Check water inlet screen for damage.
4. Check high pressure hose for leaks.
5. Check detergent siphoning tube for damage.
6. Check spray gun and nozzle extension assembly
for leaks.
7. Rinse out garden hose to flush out debris.
Pressure Washer Maintenance
Clean Debris
Daily or before use, clean accumulated debris from
pressure washer. Keep linkage, spring and controls
clean. Keep area around and behind muffler free from
any combustible debris. Inspect cooling air slots and
openings on the pressure washer. These openings
must be kept clean and unobstructed.
Pressure washer parts should be kept clean to reduce the
risk of overheating and ignition of accumulated debris.
• Use a damp cloth to wipe exterior surfaces clean.
NOTICE Improper treatment of pressure washer
could damage it and shorten its life.
• DO NOT insert any objects through cooling slots.
• Use a soft bristle brush to loosen caked on dirt,
oil, etc.
• Use a vacuum cleaner to pick up loose dirt and
debris.
Check and Clean Inlet Screen
Examine the screen on the pump’s water inlet. Clean
it if the screen is clogged or replace it if screen is
damaged.
First 5 Hours
• Change engine oil
Every 8 Hours or Daily
• Check/clean water inlet screen
1
• Check high pressure hose
• Check detergent siphoning tube
• Check spray gun and assembly for leaks
• Clean debris
• Check engine oil level
Every 25 Hours or Yearly
• Clean engine air cleaner
2
Every 50 Hours or Yearly
• Change engine oil
2
• Inspect muffler and spark arrester
Yearly
• Replace engine air cleaner
• Service spark plug
• Clean cooling system
2
Not for
Reproduction
16 BRIGGSandSTRATTON.COM
Check High Pressure Hose
The high pressure hose can develop leaks from wear,
kinking, or abuse. Inspect the hose each time before
using it. Check for cuts, leaks, abrasions or bulging
of cover, damage or movement of couplings. If any of
these conditions exist, replace the hose immediately.
Check Detergent Siphoning Tube
Examine detergent tube and clean if clogged. The tube
should fit tightly on the barbed fitting. Examine the tube
for leaks or tears. Replace the tube if damaged.
Detergent Siphoning Check Ball
Occasionally check ball in detergent siphoning
system may become stuck from storage, dried soap,
or minerals in water. The check ball can be freed by
performing the following:
NOTICE Before performing this procedure, be sure
you are wearing safety goggles as described below.
1. Shut OFF engine and turn off water supply.
2. ALWAYS point spray gun in a safe direction,
press red button and squeeze spray gun trigger to
release retained high water pressure.
3. Remove detergent siphoning hose from barbed
fitting on pump.
4. Using a firm, blunt object 7/64” in diameter or
smaller, by at least 1” long, such as an Allen
wrench, slowly insert the object into the barbed
fitting until you meet resistance. This resistance is
the check ball.
5. Slowly push down until you feel the ball move
slightly, push no more than 1/8”. Slight pressure
may be required to free the ball.
6. Repeat steps 4 and 5 if necessary.
7. Reinstall detergent siphoning hose onto barb
fitting.
8. Treat with PumpSaver as described in Protecting
the Pump during storage to prevent reoccurrence.
Check Spray Gun
Examine the hose connection to the spray gun and
make sure it is secure. Test the trigger by pressing the
red button and making sure the trigger “springs back”
into place when you release it. You should not be able
to press the trigger without pressing the red button.
Replace spray gun immediately if it fails any of these
tests.
Spray Tip Maintenance
A pulsing sensation felt while squeezing the spray gun
trigger may be caused by excessive pump pressure.
The principal cause of excessive pump pressure is a
spray tip clogged or restricted with foreign materials,
such as dirt, etc. To correct the problem, immediately
clean the spray tip following these instructions:
1. Shut OFF engine and turn off water supply.
2. ALWAYS point spray gun in a safe direction,
press red button and squeeze spray gun trigger to
release retained high water pressure.
3. Remove spray tip from end of nozzle extension.
4. Use a small paper clip to free any foreign material
clogging or restricting spray tip (A).
5. Remove nozzle extension from spray gun.
A
WARNING Risk of eye injury.
Spray could splash back or propel objects
resulting in serious injury.
• Always wear indirect vented (chemical splash) safety
goggles marked to comply with ANSI Z87.1 when using
or in vicinity of this equipment.
• NEVER substitute safety glasses or dry-condition
goggles for indirect vented safety goggles.
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected, which
could result in serious injury.
• Keep high pressure hose connected to pump and spray
gun while system is pressurized.
• ALWAYS point spray gun in safe direction, press red
button and squeeze spray gun trigger to release high
pressure, every time you stop engine.
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected, which
could result in serious injury.
• Keep high pressure hose connected to pump and spray
gun while system is pressurized.
• ALWAYS point spray gun in safe direction, press red
button and squeeze spray gun trigger to release high
pressure, every time you stop engine.
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
• NEVER repair high pressure hose. Replace it.
• Replacement hose rating MUST equal or exceed
maximum pressure rating of unit.
Not for
Reproduction
17
6. Using a garden hose, remove additional debris
by back flushing water through nozzle extension.
Back flush between 30 to 60 seconds.
7. Reinstall spray tip into nozzle extension.
8. Reconnect nozzle extension to spray gun.
9. Make sure garden hose is connected to water
inlet. Check that high pressure hose is connected
to spray gun and pump. Turn on water.
10. Start engine following instructions How to Start
Your Pressure Washer.
11. Test pressure washer by operating with each
quick connect spray tip.
O-Ring Maintenance
Purchase an O-Ring/Maintenance Kit, model 705001,
by contacting the nearest authorized service center.
It is not included with the pressure washer. This kit
includes replacement o-rings, rubber washer and water
inlet filter. Refer to the instruction sheet provided in the
kit to service your unit’s o-rings.
Engine Maintenance
Oil
Oil Recommendations
We recommend the use of Briggs & Stratton Warranty
Certified oils for best performance. Other high-quality
detergent oils are acceptable if classified for service
SF, SG, SH, SJ or higher. DO NOT use special
additives.
Outdoor temperatures determine the proper oil
viscosity for the engine. Use the chart to select the
best viscosity for the outdoor temperature range
expected.
* Below 40°F (4°C) the use of SAE 30 will result in hard
starting.
** Above 80°F (27°C) the use of 10W30 may cause
increased oil consumption. Check oil level more frequently.
Checking Oil Level
Oil level should be checked prior to each use or
at least every 8 hours of operation. Keep oil level
maintained.
1. Make sure pressure washer is on a level surface.
2. Remove oil dipstick and wipe dipstick with clean
cloth. Replace and tighten dipstick. Remove and
check oil level.
3. Verify oil is at FULL mark (top hole) on dipstick.
Replace and tighten dipstick.
Adding Engine Oil
1. Make sure pressure washer is on a level surface.
2. Check oil level as described in Checking Oil
Level.
3. If needed, slowly pour oil into oil fill opening to the
FULL mark on dipstick. DO NOT overfill.
NOTICE Overfilling with oil could cause the engine
to not start, or hard starting.
• DO NOT overfill.
• If over the FULL mark (top hole) on dipstick, drain oil to
reduce oil level to FULL mark on dipstick.
4. Replace and tighten dipstick.
Changing Engine Oil
If you are using your pressure washer under extremely
dirty or dusty conditions, or in extremely hot weather,
change the oil more often.
Full
Add
WARNING Unintentional sparking could cause
fire or electric shock resulting in
death or serious injury.
WHEN ADJUSTING OR MAKING REPAIRS TO YOUR
PRESSURE WASHER
• Disconnect the spark plug wire from the spark plug and
place the wire where it cannot contact spark plug.
WHEN TESTING FOR ENGINE SPARK
• Use approved spark plug tester.
• DO NOT check for spark with spark plug removed.
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
• NEVER repair leaking connections with sealant of any
kind. Replace o-ring or seal.
CAUTION Avoid prolonged or repeated skin
contact with used motor oil.
• Used motor oil has been shown to cause skin cancer in
certain laboratory animals.
• Thoroughly wash exposed areas with soap and water.
Not for
Reproduction
18 BRIGGSandSTRATTON.COM
KEEP OUT OF REACH OF CHILDREN.
DON’T POLLUTE. CONSERVE
RESOURCES. RETURN USED OIL TO
COLLECTION CENTERS.
Change oil while engine is still warm from
running, as follows:
1. Drain fuel tank by running pressure washer until
fuel tank is empty.
2. Disconnect spark plug wire and keep it away from
spark plug.
3. Clean area around oil fill, remove oil fill cap/
dipstick. Wipe dipstick clean.
4. Tip your pressure washer to drain oil from oil fill
into a suitable container making sure you tip your
unit away from spark plug. When crankcase is
empty, return pressure washer to upright position.
5. Slowly pour recommended oil (about 15 oz.
(0.44 liters)) into oil fill opening. Pause to permit
oil to settle. Fill to FULL mark (top hole) on
dipstick.
6. Wipe dipstick clean each time oil level is checked.
DO NOT overfill.
7. Replace and tighten dipstick.
8. Wipe up any remaining oil.
9. Reconnect spark plug wire to spark plug.
Service Air Cleaner
Your engine will not run properly and may be damaged
if you run it with a dirty air cleaner. Service more often
if operating under dirty or dusty conditions.
To service the air cleaner, follow these steps:
1. Lift tab slightly on top of air cleaner cover (A), tilt
down and remove cover.
2. Carefully remove air cleaner to prevent debris
from falling into carburetor.
3. Wash foam air cleaner (B) in liquid detergent and
water. Squeeze dry in a clean cloth.
4. SATURATE foam air cleaner in engine oil and
squeeze in a clean cloth to remove excess oil.
5. Reinstall clean or new foam air cleaner in
base (C).
6. Place tabs at bottom of cover in slots of base, tilt
cover up and snap closed.
Service Spark Plug
Changing the spark plug will help your engine to start
easier and run better.
1. Clean area around spark plug.
2. Remove and inspect spark plug.
3. Replace spark plug if electrodes are pitted,
burned or porcelain is cracked. Use the
recommended replacement plug. See
Specifications.
4. Check electrode gap with wire feeler gauge and
reset spark plug gap to recommended gap if
necessary (see Specifications).
5. Install spark plug and tighten firmly.
Inspect Muffler and Spark Arrester
Inspect the muffler for cracks, corrosion, or other
damage. Remove the spark arrester, if equipped, and
inspect for damage or carbon blockage. If replacement
parts are required, make sure to use only original
equipment replacement parts.
WARNING Exhaust heat/gases could ignite
combustibles, structures or damage
fuel tank causing a fire, resulting in
death or serious injury.
Contact with muffler area could cause burns
resulting in serious injury.
• DO NOT touch hot parts and AVOID hot exhaust gases.
• Allow equipment to cool before touching.
• Keep at least 5 ft. (1.5 m) of clearance on all sides of
pressure washer including overhead.
• It is a violation of California Public Resource Code,
Section 4442, to use or operate the engine on any forest-
covered, brush-covered, or grass-covered land unless
the exhaust system is equipped with a spark arrester, as
defined in Section 4442, maintained in effective working
order. Other states or federal jurisdictions may have
similar laws.
Contact the original equipment manufacturer, retailer,
or dealer to obtain a spark arrester designed for the
exhaust system installed on this engine.
• Replacement parts must be the same and installed in the
same position as the original parts.
B
A
C
Not for
Reproduction
19
Air Cooling System
Over time debris may accumulate in cylinder cooling
fins and cannot be observed without partial engine
disassembly. For this reason, we recommend you have
a qualified service dealer clean the cooling system per
recommended intervals (see Maintenance Schedule in
beginning of Maintenance section). Equally important
is to keep top of engine free from debris. See Clean
Debris.
Carburetor Adjustment
The carburetor on this engine is low emission. It is
equipped with a non-adjustable idle mixture valve.
Top speed has been set at the factory. If adjustment is
required, see an authorized service dealer.
After Each Use
Water should not remain in the unit for long periods
of time. Sediments or minerals can deposit on pump
parts and freeze pump action. Follow these procedures
after every use:
1. Shut OFF engine, turn off water supply, point gun
in a safe direction, press red button and squeeze
trigger to relieve trapped pressure, and let engine
cool.
2. Turn off water supply and disconnect garden hose
from water inlet on pressure washer pump.
3. Disconnect high pressure hose from spray gun
and high pressure outlet on pump. Drain water
from hose, gun, and nozzle extension. Use a rag
to wipe off the hose.
4. Place the spray gun and nozzle extension in the
accessory tray. Hang high pressure hose on hook
attached to accessory tray.
5. Empty pump of all pumped liquids by pulling recoil
handle about six times. This should remove most
liquid in pump.
6. Store unit in a clean, dry area.
7. If storing for more than 30 days, see Long Term
Storage on next page.
CAUTION
Excessively high operating speeds
could result in minor injury.
Excessively low speeds impose a heavy load.
• DO NOT tamper with governor spring, links or other
parts to increase engine speed. Pressure washer
supplies correct rated pressure and flow when running at
governed speed.
• DO NOT modify pressure washer in any way.
WARNING Fuel and its vapors are extremely
flammable and explosive which could
cause burns, fire or explosion resulting
in death or serious injury.
WHEN STORING FUEL OR EQUIPMENT WITH FUEL
IN TANK
• Store away from furnaces, stoves, water heaters, clothes
dryers, or other appliances that have pilot light or other
ignition source because they could ignite fuel vapors.
WARNING The high pressure stream of water
that this equipment produces could cut
through skin and its underlying tissues,
resulting in serious injury and possible
amputation.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected, which
could result in serious injury.
• Keep high pressure hose connected to pump and spray
gun while system is pressurized.
• ALWAYS point spray gun in safe direction, press red
button and squeeze spray gun trigger to release high
pressure, every time you stop engine.
Not for
Reproduction
20 BRIGGSandSTRATTON.COM
Winter Storage
NOTICE You must protect your unit from freezing
temperatures.
• Failure to do so will permanently damage your pump and
render your unit inoperable.
• Freeze damage is not covered under warranty.
To protect the unit from freezing temperatures:
1. Follow steps 1-5 in the previous section After
Each Use.
2. Use pump saver, Model 6039, to treat pump. This
minimizes freeze damage and lubricates pistons
and seals.
3. If pump saver is not available, connect a 3 ft.
(92 cm) section of garden hose to water inlet
adapter. Pour RV-antifreeze (antifreeze without
alcohol) into hose. Pull recoil handle twice.
Disconnect 3 ft. (92 cm) hose.
4. Store unit in a clean, dry area.
Long Term Storage
If you do not plan to use the pressure washer for more
than 30 days, you must prepare the engine and pump
for long term storage.
Protect Fuel System
Fuel Additive:
Fuel can become stale when stored over 30 days.
Stale fuel causes acid and gum deposits to form in
the fuel system or on essential carburetor parts. To
keep fuel fresh, use Briggs & Stratton® Advanced
Formula Fuel Treatment & Stabilizer, available
wherever Briggs & Stratton genuine service parts are
sold.
There is no need to drain gasoline from the engine
if a fuel stabilizer is added according to instructions.
Run the engine for 2 minutes to circulate the stabilizer
throughout the fuel system before storage.
If gasoline in the engine has not been treated with a
fuel stabilizer, it must be drained into an approved
container. Run the engine until it stops from lack
of fuel. The use of a fuel stabilizer in the storage
container is recommended to maintain freshness.
Change Engine Oil
While engine is still warm, drain oil from crankcase.
Refill with recommended grade. See Changing Engine
Oil in Engine Maintenance.
Protecting the Pump
To protect the pump from damage caused by mineral
deposits or freezing, use PumpSaver, Model 6039,
to treat pump. This prevents freeze damage and
lubricates pistons and seals.
NOTICE PumpSaver is available as an optional
accessory. It is not included with the pressure washer.
Contact the nearest authorized service center to
purchase PumpSaver.
NOTICE You must protect your unit from freezing
temperatures.
• Failure to do so will permanently damage your pump and
render your unit inoperable.
• Freeze damage is not covered under warranty.
To use PumpSaver, make sure the pressure washer is
turned off and disconnected from supply water. Read
and follow all instructions and warnings given on the
PumpSaver container.
Other Storage Tips
1. DO NOT store fuel from one season to another
unless it has been treated as described in Protect
Fuel System.
2. Replace fuel container if it starts to rust. Rust and/
or dirt in fuel can cause problems if it’s used with
this unit.
3. Cover unit with a suitable protective cover that
does not retain moisture.
4. Store unit in a clean and dry area.
WARNING Storage covers could cause a fire
resulting in death or serious injury.
• DO NOT place a storage cover over a hot pressure
washer.
• Let equipment cool for a sufficient time before placing the
cover on the equipment.
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
Simplicity 020581-01 Manuel utilisateur
- Catégorie
- Nettoyeurs haute pression
- Taper
- Manuel utilisateur
- Ce manuel convient également à
dans d''autres langues
- English: Simplicity 020581-01 User manual