Araknis Networks AN-810-AP-I-AC Guide de démarrage rapide

Marque: Araknis Networks

Modèle: AN-810-AP-I-AC

Catégorie: La mise en réseau

Taper: Guide de démarrage rapide

Ce manuel convient également à

WAVE 2 AC WIRELESS ACCESS POINT

Quick Start Guide

AN-510-AP-I-AC

AN-810-AP-I-AC

Araknis Networks Wireless Access Point

Quick Start Guide

Araknis Networks Wireless Access Point

Quick Start Guide

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment

o and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modiﬁcations not expressly approved by the party responsible for compliance

could void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This

device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

This device is designed for indoor use only.

IMPORTANT NOTE:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

In the North American market, only channels 1–11 can be operated. Other channels cannot be selected.

Industry Canada Statement

This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two

conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation of the

device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence.

L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2)

l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible

d’en compromettre le fonctionnement.

Caution:

(i) The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful

interference to co-channel mobile satellite systems;

(ii) For product available in the USA/Canada market, only channel 1–11 can be operated. Selection of other

channels is not possible.

Avertissement:

(i) Les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés uniquement pour une utilisation à

l’intérieur aﬁn de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les

mêmes canaux;

(ii) Pour les produits disponibles aux États-Unis / Canada du marché, seul le canal 1 à 11 peuvent être exploités.

Sélection d’autres canaux n’est pas possible.

Araknis Networks Wireless Access Point

Quick Start Guide

Araknis Networks Wireless Access Point

Quick Start Guide

Industry Canada Statement, Continued

Radiation Exposure Statement:

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Déclaration d’exposition aux radiations:

Cet équipement est conforme aux limites d’exposition aux rayonnements ISED établies pour un environnement

on contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source

de rayonnement et votre corps.

Industry Canada Warning

This product meets the applicable Innovation, Science and Economic Development Canada technical speciﬁcations.

Ce produit repond aux speciﬁcations techniques applicables a l'innovation, Science et Développement economique

Canada

CE Warning

This is a product with CE certiﬁcation. In a domestic environment, this product may cause radio interference, in

which case the user may be required to take adequate measures.

These products are intended to be powered by either PoE/PoE+ or a 12V/2A power supply.

These products use PoE/PoE+ IN(48V/0.53A) for both the AN-510-AP-I-AC and AN-810-AP-I-AC.

CE Statement

This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with minimum distance 20 cm between the radiator & your body.

All operational modes:

2.4GHz: 802.11b, 802.11g, 802.11n (HT20), 802.11n (HT40), 802.11ac (VHT20), 802.11ac (VHT40)

5GHz: 802.11a, 802.11n (HT20), 802.11n (HT40), 802.11ac (VHT20), 802.11ac (VHT40), 802.11ac (VHT80)

The frequency and the maximum transmitted power in EU are listed below:

AN-510-AP-I-AC AN-810-AP-I-AC

2412-2472MHz: 14.7 dBm 2412-2472MHz: 17dBm

5180-5240MHz: 17.4 dBm 5180-5240MHz: 18dBm

The device is restricted to indoor use only when operating in the 5150 to 5350 MHz frequency range..

AT BE BG HR CY CZ DK

EE FI FR DE EL HU IE

IT LV LT LU MT NL PL

PT RO SK SI ES SE UK

Araknis Networks Wireless Access Point

Quick Start Guide

Araknis Networks Wireless Access Point

Quick Start Guide

Welcome to Araknis Networks™

Thank you for choosing an Araknis™ WAVE 2 AC Wireless Access Point (WAP). With newly designed circular

housing, an ingeniously easy new mounting system, convenient PoE power, and the latest WAVE 2 AC wireless

technologies, these products are ideal as staples in both residential and commercial applications.

Features

• Sleek Circular Design

• Unobtrusive Recessed Lighting

• 1 x Gigabit LAN Port (w/802.3at PoE-IN)

• 1 x Gigabit LAN Port (data only)

• 1 x USB 2.0 (power only)

• Multi-User MIMO

• AN-510-AP-I-AC: 2x2 Dual-Band Wave 2-AC 1300Mbps

• AN-810-AP-I-AC: 4x4 Dual-Band Wave 2-AC 2600Mbps

• OvrC Enabled

Step 1: Unbox

Tile Ceiling

Mounting Hardware

Wood Surface

Mounting Hardware

(510 has 2 screws)

Wireless Access Point

(WAP)*

AN-510-AP-I-AC

AN-810-AP-I-AC

Mounting Bracket

Male-to-Female

Category Jumper Cable

Tile Ceiling Backing Plate Quick Start Guide

*This manual uses the 810 WAP for illustrative purposes throughout.

Drywall

Mounting Hardware

Araknis Networks Wireless Access Point

Quick Start Guide

Araknis Networks Wireless Access Point

Quick Start Guide

Step 2: Install Position the Ceiling Mount

Ceiling Mount Wall Mount

Position A Position B

A B

NOTE: Use the ceiling back plate on top of acoustic ceiling tiles to prevent the mounting nuts from pulling through.

* Center line of the bracket is not necessarily the center line of the WAP when installed. Please use the guide above to understand the

center line of the WAP when installing the bracket.

Position 2

Position 1

Ceiling Mount

Center

Line*

Center

Line*

Ceiling Tiles

WAP

Araknis Networks Wireless Access Point

Quick Start Guide

Araknis Networks Wireless Access Point

Quick Start Guide

Step 3: Connect

Router

Internet

WANLAN

AN-ACC-INJ-30W

DATA (IN)DC 48V Input Power

POWER + DATA (OUT)

PoE Injector

(not included)

WAP

AN-310-SW-F-8-POE

PoE Switch

Switch

DC Power Supply

(not included)

Recommended use of the Jumper Cable

Position A (810) Position B (510/810)

NOTE: Jumper is needed when using Cat 6A in Position B.

WANLAN

You can mount your access point to the electrical box in one of two positions, shown below. These options are

provided to provide cable bend relief for cables of dierent lengths and thicknesses. Illustrations do not reﬂect

pre-install steps—please run the wire or jumper prior to connecting the access point.

Center lineCenter line Center LineCenter Line

Double Gang

Box (not

included)

Single Gang

Box (not

included)

Jumper

Cat 6A

Cat 5e

Araknis Networks Wireless Access Point

Quick Start Guide

Araknis Networks Wireless Access Point

Quick Start Guide

Step 4: Verify

LED Status:

• Blinking: WAP is not working correctly. Contact Araknis technical support.

• Solid White: WAP is booting up (810 only).

• Solid Blue: WAP is operating correctly.

Step 5: Log Into Web Interface

NOTE: If you can’t connect to the WAP using this method, or need to conﬁgure the device before connecting it to the network, try these

options for accessing your device:

• DHCP IP address – Page 15

• Default IP Address – Page 16

• OvrC – Page 19

Username araknis

Password araknis

LED* LED*

*NOTE: The LED is located on the side of the device.

Araknis Networks Wireless Access Point

Quick Start Guide

Araknis Networks Wireless Access Point

Quick Start Guide

Pro Tip: Save and Apply Changes

After making changes to settings on a

menu page, click the “Save” button on

the menu to hold the new settings in the

Apply Changes ﬁeld.

NOTE: Settings will take aect after the progress bar completes 100%.

Other Access Methods: DHCP IP Address

The WAP is conﬁgured to DHCP by default so that the DHCP server can assign an IP address when the WAP is

connected to the network (the DHCP server is usually the router). This address can be used for accessing the

web interface.

Use one of these methods to ﬁnd the IP address of the WAP:

• Check the client table on your router

• Use a network scanner (e.g. Fing) to sni the network. The

Araknis WAP manufacturer ﬁeld will display “Snap AV”

See the highlighted ﬁeld in the "Fing" screenshot to the

right for an example of an Araknis device being identiﬁed.

After all desired changes have been made,

click “Apply Changes” to review the new

settings if any. Click "Apply" to make the

changes or "Revert" to cancel the changes.

Araknis Networks Wireless Access Point

Quick Start Guide

Araknis Networks Wireless Access Point

Quick Start Guide

Other Access Methods: Default IP Address

If the WAP is not issued an IP address on the network, or needs to be accessed while not connected to a

network, you can conﬁgure your computer's network connection to allow access using the default IP address,

“192.168.20.253”.

Connect your PC to the WAP

using a network patch cable.

On your PC, open the Control

Panel and left-click “Network

and Internet”.

Left-click “Network and Sharing

Center”.

A B C

Windows 7 screenshots shown for reference.

Computer WAP

Other Access Methods: Default IP Address

D E F

In the left bar, left-click “Change

adapter settings”.

Right-click the icon for the

wired network connection and

left-click "Properties".

Left-click to highlight “Internet

Protocol Version 4 (TCP/IPv4),

then left-click “Properties”.

Windows 7 screenshots shown for reference.

Araknis Networks Wireless Access Point

Quick Start Guide

Araknis Networks Wireless Access Point

Quick Start Guide

Other Access Methods: Default IP Address

G H I

Left-click “OK” to close Internet

Protocol Version 4 (TCP/IPv4)

Properties, then left-click "OK"

to close wireless network

connection properties.

In the “General” tab, left-click

"Use the following IP address:"

and enter the IP address and

subnet mask.

IP Address 192.168.20.2

Subnet Mask 255.255.255.0

Open a browser and navigate

to http://192.168.20.253/. Log

in using the default credentials:

Username araknis

Password araknis

Windows 7 screenshots shown for reference.

Other Access Methods: OvrC

OvrC gives you remote device management, real-time notiﬁcations, and intuitive customer management, right

from your computer or mobile device. Setup is plug-and-play, with no port forwarding or DDNS address required.

To add this device to your OvrC account:

Connect the WAP to the Internet

Log Into OvrC (www.ovrc.com)

Add the Device (MAC address and Service Tag numbers needed for authentication)

Internet

OvrC Server

Web Browser

Access

Mobile

Apps

WANLAN

AN-110-SW-R-8

1 2 3 4 5 6 7 8

1 Gbps

Link/Act

Warning

This product can expose you to chemicals including lead and lead compounds, which are known to the State of

California to cause cancer. For more information go to www.P65Warnings.ca.gov.

Contacting Technical Support

(866) 838-5052 techsupport@araknisnetworks.com

2-Year Limited Warranty

Araknis Networks® products have a 2-Year Limited Warranty. This warranty includes parts and labor repairs

on all components found to be defective in material or workmanship under normal conditions of use. This

warranty shall not apply to products that have been abused, modiﬁed, or disassembled. Products to be

repaired under this warranty must be returned to SnapAV or a designated service center with prior notiﬁcation

and an assigned return authorization (RA) number.

US local representative information:

Company: Araknis Networks

Address: 1800 Continental Blvd. Suite 300,

Charlotte, NC 28273

USA

Tel: 704.927.7620

Fax: 800.782.2410

200213-1313

Araknis Networks AN-810-AP-I-AC Guide de démarrage rapide

Marque: Araknis Networks

Modèle: AN-810-AP-I-AC

Catégorie: La mise en réseau

Taper: Guide de démarrage rapide

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Araknis Networks AN-810-AP-I-AC Quick start guide

Araknis Networks AN-810-AP-I-AC Guide de démarrage rapide

Ce manuel convient également à

Araknis Networks AN-810-AP-I-AC Guide de démarrage rapide

dans d''autres langues

Documents connexes

Autres documents