Certification Exhibit
Manufacturer: Itron, Inc.
Manual
Model: ACT2
FCC ID: SK9ACT2
IC: 864G-ACT2
FCC Rule Part: 15.247
ISED Canada’s Radio Standards Specification: RSS-247
TÜV SÜD Project Number: 72166854
6 June 2012
Page 1 of 5
Date: April 6, 2017
PIL #:
Product Line: OpenWay® Riva™ CENTRON®
Distribution:
Itron Internal Customers
Distributors / Manufacturer Reps
6 June 2012
Page 2 of 5
Installation of OpenWay Riva CENTRON Meter Remote
Antenna Flex Coupler
Itron is announcing the availability of a remote antenna solution for use with the
OpenWay Riva CENTRON meter. This assembly is designed for installation
configurations where it is necessary to extend the RF antenna inside the meter; for
example, basement installations or metal enclosures. This antenna does not provide
any amplification of the RF signal, but provides a method to relocate the transceiver.
Some signal attenuation is expected with this configuration.
The assembly consists of an Itron flex coupler that fits the outer cover of the meter. This
allows for attaching customer provided remote fixed antennas and cabling. See Figure
1 below for a photo of the flex coupler assembly.
Figure 1: Flex Coupler Assembly
6 June 2012
Page 3 of 5
Approved customer supplied antenna specifications
Since each customer deployment will be unique with regards to the required cabling and
type of antenna, the cabling and antennas will be customer provided.
Note: Under ISED Canada regulations, this radio transmitter may only operate using an
antenna of a type and maximum (or lesser) gain approved for the transmitter by ISED.
To reduce potential radio interference to other users, the antenna type and its gain
should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more
than that necessary for successful communication.
This radio transmitter (identify the device by certification number, or model number if
Category II) has been approved by ISED to operate with the antenna types listed below
with the maximum permissible gain and required antenna impedance for each antenna
type indicated. Antenna types not included in this list, having a gain greater than the
maximum gain indicated for that type, are strictly prohibited for use with this device.
Remarque: En vertu de la réglementation ISED Canada, cet émetteur radio ne peut
fonctionner qu'avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé
pour l'émetteur par l'ISED. Pour réduire les interférences radio potentielles avec
d'autres utilisateurs, le type d'antenne et son gain devraient être choisis de façon à ce
que la puissance éloignée isotrope équivalente (e.i.r.p.) ne soit pas supérieure à celle
nécessaire à une communication réussie.
Cet émetteur radio (identifiez le périphérique par numéro de certification ou numéro de
modèle si Catégorie II) a été approuvé par l'ISED pour fonctionner avec les types
d'antennes répertoriés ci-dessous avec le gain maximal admissible et l'impédance
d'antenne requise pour chaque type d'antenne indiqué. Les types d'antenne non inclus
dans cette liste, ayant un gain supérieur au gain maximal indiqué pour ce type, sont
strictement interdits pour être utilisés avec cet appareil.
6 June 2012
Page 4 of 5
Customer supplied remote antennas should meet the following specifications.
Elevated Feed Point Whip Antenna
Frequency: 890 - 960 MHz
VSWR: 2.0:1 or less
Maximum Gain: 3.0 dBi
Low Profile Radome Antenna
Frequency: 806 - 960 MHz
VSWR: 2.0:1 or less
Maximum Gain: 2.14 dBi
Dual Band Tri Mode Stub Antenna
Frequency: 700 - 960 MHz
VSWR: 2.0:1 or less
Maximum Gain: 2.0 dBi
Customer supplied cabling recommendation
The Itron flex antenna is supplied with an SMA male connector. Customer supplied
cabling that attaches to the Itron flex antenna should meet the following specifications.
RG58C Coaxial Cable, SMA Male / Female
50 Ohm RF (Radio Frequency) transmission
Male to female gender combination
Crimp style SMA connector
Antenna Installation Guidelines
For optimal performance, several guidelines should be followed in the installation of this
remote antenna.
These include:
• Mounting the antenna in the proximity to the nearest structure.
• For inside installations, remote antennas may be mounted in the proximity of an
available window, or routed to the outside if the signal strength is not great
enough.
• Mounted so the cable between meter and antenna will not be compromised or
damaged.
6 June 2012
Page 5 of 5
Flex Antenna Installation Procedure
1. Clean the meter cover where the flex antenna will be installed. Wipe area with
alcohol wipes and let dry one minute.
2. When using the flex antenna with Velcro mount, a recommended 3M Adhesion
Promoter (K-520) Stock Number JT-2800-1252-0 or similar type adhesion promoter
should be used to clean the antenna surface prior to attaching the Velcro strip. This
will help ensure proper adhesion of the Velcro to the antenna.
3. Affix the flex antenna to the outer cover as shown in Figure 1.
4. Install the remote antenna at the designated location, following the Installation
Guidelines above.
5. Once installed to the antenna, wrap the connectors in cold flow tape. Tape should be
wrapped tightly and in a continuous manner and should cover the cable one inch
past the end of the connector where it attaches to both the flex circuit patch and the
antenna.
6. Secure the cable to the side of the structure.
Part Number
Description
514258-001 Flex Coupler for OpenWay Riva CENTRON and OpenWay
CENTRON with adhesive mount
514258-004 Flex Coupler for OpenWay Riva CENTRON and OpenWay
CENTRON with Velcro mount separate; not adhered to the
antenna
Please contact your Account Manager for ordering instructions.
Should you have any questions please call Itron Support at 1-877-487-6602.
Steve Wright
Sr. Product Manager, Electric Metering
Meter Module
Technical Reference Guide
Effective Date: July, 2016
ACT2
ACT2 Meter Module
Revision History
Revision Date Description of Change
A July, 2016 Initial Release
The following table describes the changes to this document for each revision of the ACT2 meter module:
ACT2 Meter Module
Labeling
The following requirements will be applied to any products that use this module:
The end product or host label will include the following text:
The user’s manual for any product that contains this module will contain the following text. If the device is large
enough, then this will also be placed on the label.
“This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.”
Regulatory Compliance
The user’s manual for any product that contains this module will contain the following text:
FCC Part 15, Class B
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this device not expressly approved by Itron,
Inc. could void the user’s authority to operate the equipment.
Innovation, Science and Economic Development Canada (ISED)
This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired operation.
Cet appareillage numérique de la classe B répond à la norme Canadienne sur le matériel brouilleur. L'opération est
sujette aux deux conditions suivantes: (1) ce dispositif ne peut pas causer d'interférence nocive, et (2) ce dispositif doit
accepter n'importe quelle interférence reçue, y compris les interférences pouvant entraîner un fonctionnement
indésirable.
• Contains:
• FCC ID: SK9ACT2
• IC: 864G-ACT1, Model: ACT2
ACT2 Meter Module
Under Innovation, Science and Economic Development Canada regulations, this radio transmitter may only operate
using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Innovation, Science and
Economic Development Canada. To reduce potential radio interference to other users, the antenna type and its gain
should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for
successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une
antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le
but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le
type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas
l'intensité nécessaire à l'établissement d'une communication satisfaisante.
RF Exposure (FCC/ISED)
“This equipment complies with radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance 20 cm between the radiator and your body. This transmitter
must not be co-located or operating in conjunction with any other antenna or transmitter.”
“Cet équipement est conforme aux limites d'exposition aux radiations dans un environnement non contrôlé. Cet équipement
do it être installé et utilisé à distance minimum de 20 cm entre le radiateur et votre corps. Cet émetteur ne doit pas être
co-localisées ou opérant en conjonction avec tout autre antenne ou transmetteur.”
Miscellaneous
The user’s manual for any product that contains this module will contain the following text:
Professional Installation
This module is intended for professional installation by the integrator. The OEM integrator is still responsible for the
FCC compliance requirement of the end product, which integrates this module.
Modification and Repairs
To ensure FCC compliance and system performance, this device, antenna and/or coaxial assembly shall not be changed
or modified without the express written approval of Itron. Any unauthorized modification will void the user’s authority
to operate the equipment. WARNING! This device contains no user serviceable parts. Attempts to repair this device by
unauthorized personnel may subject the person to shock hazard if removal of protective covers is attempted.
Unauthorized repair will void the warranty and/or maintenance contract with your company.
General Description
Recycling Information
The product you have purchased contains circuit boards. At the end of the modules useful life, under various state
and local laws, it may be illegal to dispose of certain components into the municipal waste system. Check with your
local solid waste officials for details about recycling options or proper disposal.
About this Manual
The Itron ACT2 is an electricity metering module which includes a 902.4 MHz to 927.6 MHz transmitter as well as WiFi.
The module operates on AC as well as DC voltage which is supplied by a host device.
This technical reference guide describes the installation of the ACT2 for the Itron OPENWAY RIVA CENTRON
meter.
ACT2 Meter Module
Installation
The ACT2 module will be installed in the Itron OPENWAY RIVA CENTRON electric meter.
Shown are the meter base with metrology board, the board to board connector, the ACT2 module, the display and the
inner and outer cover.
ACT2 Meter Module
Install the display on the ACT2 module by pushing metal pins of display into module connector.
ACT2 Meter Module
Insert module into upper section of inner cover and connect two wired connectors to module.
ACT2 Meter Module
Connect metrology and the ACT2 module using the board to board connector.
ACT2 Meter Module
Install lower inner cover.
ACT2 Meter Module
Install outer cover.
ACT2 Meter Module
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
dans d''autres langues
- English: ITRON ACT2 User guide
Documents connexes
Autres documents
-
Schlage Lock COMAD400V3 Manuel utilisateur
-
TELTONIKA Networks RUT241 Mode d'emploi
-
TELTONIKA Networks RUT951 Mode d'emploi
-
SICK UE4740 PROFINET IO Mounting instructions
-
-
Beurer beurres BF 880 Diagnostic Bathroom Scale Manuel utilisateur
-
Beurer BF 980 Manuel utilisateur
-
Renkforce RAID controller card [2x M.2 NGFF - 1x SATA socket 2-pin] Le manuel du propriétaire
-
Eurotech DynaGATE 20-30 Le manuel du propriétaire
-
Intermec IM11 Integration Manual