R2X HELMET and
R2X UTILITY APP
Guide
1.1 Powering On
Press and hold the (+) Button and Center Button for 1 second.
1.2 Phone Pairing
The R2X will automatically enter the phone pairing mode when you initially turn on the R2X
or in the following situation: •Rebooting after executing Factory Reset.
1) Press and hold the (+) Button and Center Button for 1 second until the
LED flashes Blue alternately and you hear a voice prompt, “Phone pairing”.
2) With your mobile phone in Bluetooth-pairing mode, select R2X in the list of devices detected.
3) If your mobile phone asks for a PIN, enter 0000.
4) The mobile phone confirms that pairing has been completed and the R2X is ready to use.
You will hear a voice prompt, “Your headset is paired”.
1. R2X Helmet Set-Up Guide
Note:
• The phone pairing mode lasts for 3 minutes.
• To cancel phone pairing, tap the Center Button.
a. Powering On and Off
Power On : Press and hold the (+) Button and Center Button for 1 second.
Power Off : Tap the (+) Button and Center Button.
b. Phone Pairing
When using the R2X with smartphone for the first time, they will need to be “paired.”The R2X
remains paired with the devices and automatically reconnects to them when they are within range.
b.1 Initially Pairing the R2X Helmet
The R2X will automatically enter the phone pairing mode when you initially turn on the R2X
or in the following situation: •Rebooting after executing Factory Reset.
1. Press and hold the (+) Button and Center Button for 1 second until the LED flashes
Blue alternately and you hear a voice prompt, “Phone pairing”.
2. With your mobile phone in Bluetooth-pairing mode, select R2X in the list of devices detected.
3. If your mobile phone asks for a PIN, enter 0000.
4. The mobile phone confirms that pairing has been completed and the R2X is ready to use.
You will hear a voice prompt, “Your headset is paired”.
Refer. R2X Operation
b.2 Pairing When the R2X Helmet is Turned Off
1. While the R2X is off, press and hold the (+) Button and Center Button for 5 seconds
until the LED flashes Blue alternately and you hear a voice prompt, “Phone pairing”.
b.3) Pairing When the R2X Helmet is Turned On
1. While the R2X is on, press and hold the Center Button for 5 seconds until the LED
flashes Blue alternately and you hear a voice prompt, “Phone pairing”.
3) Factory Reset
To erase all of your settings and start fresh, the R2X can be restored
to factory default settings using the factory reset.
1. To restore the R2X to factory default settings, press and hold the
Center Button for 10 seconds until you hear a voice prompt, “Factory reset”.
2. Within 10 seconds, Tap the Center Button to confirm reset.
The R2X will be restored to factory setting and switched off automatically.
You will hear a voice prompt, “Headset reset, good-bye”.
2. Running the R2X Utility App
2.1 Download and install files
Download and install the APK file from the following link
https://senatech.box.com/s/5y0utqy2eokr65fpd6529rrtcpir94b7
2.2 Launch the R2X Utility App on your Android phone.
If R2X is not connected, the [Let’s Get Started] screen is displayed.
2.3 Power on the R2X helmet and Phone Pairing
Press and hold the (+) Button and Center Button for 1 second.
(refer “CH 1.2 Phone Pairing”)
2.4 Click the Next Button moves to the [Bluetooth Setting] screen of
the smartphone. Select [R2X] and go back to the app.
2.5 After connecting the device, if the firmware is the latest version,
check the connected device information and set the name.
2.6 Press the input box and the keypad appears at the bottom of the screen.
Set a name and click the Save Button to complete the name setting.
3.1 How to update the firmware when connecting R2X for the first time after
installing the R2X Utility app.
3.1.1 After connecting the device, If the device firmware is not the latest version,
it moves to the firmware update guide screen.
3.1.2 Firmware update starts when you click the [Start] button.
3.1.3 When the firmware update is complete, the [Firmware Update Complete] screen
automatically moves to the [Name Your Device] screen.
3. R2X Firmware Update
3.2 How to update the firmware when connecting R2X more than once after
installing the R2X Utility app.
3.2.1 When the R2X is powered on, it is automatically connected to the App and
it switches to the [Home] screen.
3.2.2 If the R2X needs a firmware update, it will go to the firmware update screen.
3.2.3 Firmware update starts when you click the [Start] button.
3.2.4 When the firmware update is complete, the [Firmware Update Complete] screen
automatically moves to the [Home] screen.
4.1 Running the Amazon Alexa app the first time you use the RX2 utility app.
4.1.1 When the device name setting is completed( Refer ch 3.1.2),
the [Amazon Alexa] screen appears automatically.
Click Next Button to move to the next screen.
4. Running the Amazon Alexa App
Note. Running the Amazon Alexa APP after the first use of the RX2 Utility App
1) Click the upper left of the [Home] screen -> Click [Amazon Alexa ] Button ->
Click [NEXT] Button -> Click [Amazon Alexa ] Link
4.2 Click the Amazon Alexa App link on the [Amazon Alexa Things To Try] screen.
1) If the Amazon Alexa App is not installed, click the install button to
go to the [Play Store] installation screen.
2) If the Amazon Alexa App is installed, run the Amazon Alexa App.
4.3 Log in using your Amazon Account or register with a new Amazon Account.
4.4 Click the [Devices] Button ->Click the [+] Button -> Click the [Add Device]
or
4.5 Click the [Headphones] -> Click the [Sena R2X] -> Click the [CONTINUE]
4.6 Click the [Done] -> If R2X is normally registered, click [All devices] in the
Device tap, and Sena R2X is displayed online.
5. Calling Alexa
5.1 Trigger
5.1.1 When you call “Alexa”, you hear a response tone and the Cyan LED blinks once.
5.1.2 If you press the [+] Button and [–] button at the same time, you hear a
response tone and the Cyan LED blinks once.
5.2 Calling Test
5.2.1 Ask a question with “Alexa, what is the date?”-> “Today is…..”you should hear.
6.1 Mic Mute On
1) Press the Center Button and (-) Button for 1 second.
2) Red LED lights up with high single tone.
6.2 Mic Mute off
1) Press the ‘Center’ and ‘-’buttons for 1 second.
2) Red LED turns off along with mid single tone.
6. Microphone Mute
Note.
When Mic Mute is On, it is impossible to call Alexa. (Even a button cannot be
called)
Note.
When triggering is not possible, a double tone is produced.
Note.
When Mic Mute is off, you can call Alexa. (Also available with a button)
Certification and Safety Approvals FCC Compliance Statement
This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits
for a Class B digital device pursuant to part 15 of the FCC rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment on and
off, the user is encouraged to try to correct the interference by one or
more of the following measures:
-Reorient or relocate the receiving antennae
-Increase the separation between the equipment and the receiver
-Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC RF Exposure Statement
This equipment complies with FCC radiation exposure limits set forth
for an uncontrolled environment. End users must follow the specific
operating instructions for satisfying RF exposure compliance. The
antenna used for this transmitter must not transmit simultaneously
with any other antenna or transmitter, except in accordance with FCC
multi-transmitter product procedures.
When equipped, the distance between antenna and one’s head surface
is 23mm.
FCC Caution
Any changes or modifications to the equipment not expressly approved
by the party responsible for compliance could void user’s authority to
operate the equipment.
Certification et homologation de sécurité Déclaration de conformité
FCC
Cet appareil est en conformité avec la partie 15 des règles de la FCC.
Son fonctionnement est soumis aux deux conditions suivantes :
(1) Cet appareil ne doit pas créer d’interférences préjudiciables et
(2) Cet appareil doit accepter toutes les interférences reçues, y compris
celles qui pourraient entraver son bon fonctionnement. Cet
équipement a été testé et jugé conforme aux limites pour un appareil
numérique de classe B, conformément à la partie 15 des règles de la
FCC. Ces limites sont conçues pour fournir une protection raisonnable
contre les interférences nuisibles dans une installation résidentielle.
Cet équipement génère et utilise de l’énergie radio fréquence et, s’il
n’est pas installé et utilisé conformément. aux instructions, il peut
occasionner des interférences nuisibles au niveau des communications
radios. Cependant, il n’existe aucune garantie que ces interférences ne
se produiront pas dans une installation particulière. Si cet équipement
génère des interférences nuisibles à la réception de la radio ou de la
télévision (ce qu’il est possible de déterminer en mettant l’équipement
hors tension, puis sous tension), l’utilisateur est invité à suivre une ou
plusieurs des mesures suivantes pour corriger le problème des
interférences en prenant l’une des mesures suivantes :
-Modifier l’emplacement ou l’orientation de l’antenne de réception.
-É loigner l’appareil du récepteur.
-Brancher l’appareil sur une prise située sur un circuit différent de celui
du récepteur.
-Consulter le revendeur ou un technicien expérimenté pour obtenir de
l’aide.
É noncé FCC sur l’exposition aux radiations RF
Cet équipement est conforme aux réglementations FCC d’exposition
aux radiations définies pour un environnement non contrôlé. Les
utilisateurs doivent respecter les instructions d’exploitation spécifiques
pour répondre aux exigences de conformité sur l’exposition aux RF.
L’antenne utilisée pour cet appareil ne doit pas fonctionner en même
temps qu’une autre antenne ou émetteur, sauf s’il y a conformité avec
les procédures FCC des produits multi-émetteurs.
Cet appareil est conforme à l'exigence d'exposition aux RF. Lorsque
équipé, la distance entre l’antenne et la surface de la tête est de 23mm.
Précautions FCC
Tout changement ou modification non expressément approuvé par la
partie chargée de la mise en conformité peut annuler le droit de
l’utilisateur à utiliser l’équipement.
Industry Canada(IC) Statement
This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1)this device may not cause interference, and
(2)this device must accept any interference, including interference that
may cause undesired operation of the device.
Le present appareil est conforme aux CNR d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation est
autorisee aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage
radioelectrique subi, meme si le brouillage est susceptible d’en
compromettre le fonctionnement.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
