Modern Forms WS-58814 Tower Mode d'emploi

Marque: Modern Forms

Modèle: WS-58814 Tower

Taper: Mode d'emploi

modernforms.com

Phone (800) 526.2588

Fax (800) 526.2585

Headquarters/Eastern Distribution Center

44 Harbor Park Drive

Port Washington, NY 11050

Central Distribution Center

1600 Distribution Ct

Lithia Springs, GA 30122

Western Distribution Center

1750 Archibald Avenue

Ontario, CA 91760

Modern Forms retains the right to modify the design of our products at any time as part of the company’s continuous improvement program.

WARNING

IMPORTANT: NEVER attempt any work without shutting o the electricity.

- Read all instructions before installing.

- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.

- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”

the circuit breaker switch(es) that control the power to the xture or room that you are working on.

- Place the wall switch in the “OFF” position.

CAUTION

- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out

or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.

CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.

AVERTISSEMENT

IMPORTANT : Coupez l’électricité avant TOUTE manipulation.

- Lisez toutes les instructions avant d’installer.

- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les règlements

locaux.

- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt

(« OFF »).

- Placez l’interrupteur mural en position d’arrêt (« OFF »).

MISE EN GARDEs

- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté et

ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du luminaire.

MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.

ADVERTENCIA

IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.

- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e instalación de esta

lámpara.

- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.

- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de alimentación principal

en la posición “OFF” (APAGADO).

- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).

PRECAUCIÓN

- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni

utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación ETL/CETL esta lámpara.

PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.

HARDWARE

Wire Connector

Qty: 3pcs+1 Extra

7EAC112201

Conversion plate

QTY:1Extra

4MBC111121BB1

Brass Plating

Mounting Screw

Qty: 1 Extra

4MPF0412S1BB1

5/32”-32 × 1/2

Brass Plating

Junction Box Screw

Qty: 4pcs+1 Extra

7MPF0825F1

#8-32x1

Nickle Plating

Mounting Ring

QTY:1Extra

7MBC101501

Plastic Anchor

QTY:6pcs+1Extra

7TDD082401

Wood Screw

QTY:6pcs+1Extra

7MPF2204J2 (Ni)

Ø4x7/8”

B E F G

INSTALLATION INSTRUCTION

588 – LED Wall Sconce

WS-58814 / WS-58820 / WS-58827

modernforms.com

Phone (800) 526.2588

Fax (800) 526.2585

Headquarters/Eastern Distribution Center

44 Harbor Park Drive

Port Washington, NY 11050

Central Distribution Center

1600 Distribution Ct

Lithia Springs, GA 30122

Western Distribution Center

1750 Archibald Avenue

Ontario, CA 91760

Modern Forms retains the right to modify the design of our products at any time as part of the company’s continuous improvement program.

PREPARATION

1. Shut o the power at the circuit breaker and remove existing xture,

including the crossbar.

2. Carefully unpack your new xture and lay out all the parts on a clear

area. Be careful not to lose any small parts necessary for installation.

MOUNT ON 2X4” SWITCH BOX (Fig. 1)

3. Remove the mounting screw (C) as shown in Fig. 1.

4. Drill holes in the wall aligned with the key holes located in the

mounting back plate, insert the plastic anchor (E1).

5. Secure the mounting plate to the switch box using junction box screws

(B). Fasten it to the wall with wood screw (F1), the side of the mounting

plate marked “GND” must face out.

6. Connect the xture’s wire to switch box wires as shown in Fig. 3,

making sure that all wire connectors (A) are secured. If your outlet box

has a green or bare copper ground wire, connect the xture’s ground

wire to it. Otherwise, connect the xture’s ground wire directly to the

back plate using the green screw provided. After wires are connected,

tuck them carefully inside the switch box.

7. Place the bubble crystal on the xture as shown in Fig. 1. Place the top

cover on the xture as shown, then secure it using the mounting screw

(C).

8. Secure the xture to the mounting plate using the mounting screw (C).

MOUNT ON 4X4” JUNCTION BOX (Fig. 2)

3. Remove the mounting screw (C) as shown in Fig. 1.

4. Drill holes in the wall aligned with the key holes located in the

mounting back plate, insert the plastic anchor (E1).

5. Secure the mounting ring to the junction box using the junction box

screws (B). Fasten it to the wall with wood screw (F1), The side of the

mounting ring (E) marked “GND” must face out.

6. Secure the mounting plate and conversion plate to the mounting

ring(E) using junction box screws (B) as shown in Fig. 2.. The side of the

mounting plate marked “GND” must face out.

7. Connect the xture’s wire to junction box wires as shown in Fig. 3,

making sure that all wire connectors (A) are secured. If your outlet box

has a green or bare copper ground wire, connect the xture’s ground

wire to it. Otherwise, connect the xture’s ground wire directly to the

back plate using the green screw provided. After wires are connected,

tuck them carefully inside the switch box.

8. Place the bubble crystal on the xture as shown in Fig. 1. Place the top

cover on the xture as shown, then secure it using the mounting screw

(C).

9. Secure the xture to the mounting plate using the mounting screw (C).

INSTALLATION INSTRUCTION

588 – LED Wall Sconce

WS-58814 / WS-58820 / WS-58827

Fig.1 Mount on Switch Box

Fig.2 Mount on Junction Box

Mounting Backplate Conversion Plate Dimension Mounting Ring Dimension

Fixture Wires

Black or

Smooth

Fixture Wires

White or

Ribbed

Fixture Wires

Bare wire

(Ground)

House Wires

Black

(Hot)

House Wires

White

(Neutral)

House Wires

Green or Bare Copper

(Ground)

Fig. 3 Wiring

Mounting Screw

Wood Screw

Plastic Anchor

Wire Connector

Junction Box Screw

Mounting Screw

Bubble Crystal

(RPL-GLA-58814)

(RPL-GLA-58820)

(RPL-GLA-58827)

Top Cover

Switch Box

Ground Wire

Mouting Plate

Fixture

Ground Wire

Junction Box

Junction Box Screw

Wire Connector

Mounting Ring

Conversion Plate

Mounting Plate

41/2"

11/2"

41/2"

13/8"

13/4"

57[21/4"]

13/4"11/2"

WS-58814126/8"

WS-58820187/8"

WS-58827243/8"

t pJ RUUNQWTj _` PORTMN

t pJ RUUOMWTj _` QURTMN

t pJ RUUOTWTj _` RMRTMN

WS-58814 12 6/8”

WS-58820 18 7/8”

WS-58827 24 3/8”

WS-58814:7MBC325701

WS-58820:7MBC485701

WS-58827:7MBC505701

57 [2 1/4”]

1 1/2” 1 3/4”

4 1/2” 4 1/2”

4 1/2”

1 1/2”

4MBC111121BB1 7MBC101501

1 3/8”

1 3/4”

4”

1Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JAN 2023 G0

modernforms.com

Phone (800) 526.2588

Fax (800) 526.2585

Headquarters/Eastern Distribution Center

44 Harbor Park Drive

Port Washington, NY 11050

Central Distribution Center

1600 Distribution Ct

Lithia Springs, GA 30122

Western Distribution Center

1750 Archibald Avenue

Ontario, CA 91760

INSTALLATION INSTRUCTION

Trimless Junction Box Cover

MKCP-3040-WT

OVERALL COMPONENT DIMENSIONS

CAUTION: TO PREVENT ELECTRICAL SHOCK, ENSURE ELECTRICITY HAS BEEN TURNED OFF AT THE CIRCUIT BREAKER BEFORE

BEGINNING.

-Read all instructions before installing.

-System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.

-When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.

-Retain installation instructions for future maintenance reference.

WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or

accessories designated for use by Modern Forms. Substitution of parts or accessories not designated for use with this product by Modern Forms

could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any parts are

damaged or missing.

MISE EN GARDE: POUR ÉVITER TOUT CHOC ÉLECTRIQUE, ASSUREZVOUS QUE LE DISJONCTEUR SOIT MIS HORS TENSION AVANT DE

COMMENCER.

-Lisez toutes les instructions avant l’installation.

-Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux règlements

locaux.

-Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.

ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement avec

les pièces et/ou accessoires fournis pour être utilisés avec les produits Modern Forms. Remplacer des pièces ou accessoires non conçus pour ce

produit Modern Forms pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la garantie. Veuillez

contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.

COMPONENT OVERVIEW

The trimless junction box cover is intended for installation to NEC approved 4” square junction boxes recessed in drywall and ush with the

support structure. It may be covered with spackle and/or plaster to conceal junction box visibility. It is to be connected to compatible Modern

Forms xtures. Refer to specications sheets for more information.

TYP

HARDWARE

Wire Connector

Qty: 3 (+1 Extra)

½” Plastic Spacer

Qty: 2

⁄”-40 x 1⁄” Long

Mounting Screw

Qty: 2 (+1 Extra)

¾” Plastic Spacer

Qty: 2

#8-32 x ¾” Long

Junction Box Screw

Qty: 2 (+1 Extra)

1” Plastic Spacer

Qty: 2

NOTE: This accessory is supplied with an optional mounting C-ring for

xture connection via ⁄” K.O. hole. This component may be omitted

from the installation if mounting xtures using #8 screw holes.

2Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JAN 2023 G0

modernforms.com

Phone (800) 526.2588

Fax (800) 526.2585

Headquarters/Eastern Distribution Center

44 Harbor Park Drive

Port Washington, NY 11050

Central Distribution Center

1600 Distribution Ct

Lithia Springs, GA 30122

Western Distribution Center

1750 Archibald Avenue

Ontario, CA 91760

INSTALLATION INSTRUCTION

Trimless Junction Box Cover

MKCP-3040-WT

FIG. 1

FIG. 2

FIG. 4

TRIMLESS JUNCTION BOX COVER INSTALLATION:

The trimless junction box cover is compatible with NEC approved

4” square junction boxes recessed in drywall and ush with the

support structure.

1. Install compatible junction box (by others) to the framing

structure. Ensure the junction box is ush with the base or front

of framing structure (See FIG. 1).

2. Install the mounting plate to the junction box (See FIG. 2).

Ensure the spacer alignment base is facing outward.

FIG. 3

105mm

FIG. 5 FIG. 6

3. Determine the drywall thickness and select the appropriate

spacer to install between the mounting plate and the trimless

junction box cover (See FIG. 3).

NOTE: Only 1 matching pair of spacers are to be used per

installation.

4. Using the mounting screws provided, attach the trimless

junction box cover to the mounting plate (See FIG. 4).

5. Make a 4⁄” square cutout in drywall at the intended trimless

junction box cover location and proceed to install to framing

structure (See FIG. 5). Apply and nish spackle up to the center

hole of trimless junction box cover. Ensure #8 holes on the

cover are free of spackle. (See FIG. 6).

Mounting Plate

Plastic

Spacers

Trimless Junction Box Cover

Cover Mounting Screws

Ground Wire

Example: ½” Drywall (No Spacer)

⁄”½”

Spacer Alignment

Base

Spacer

Height

Drywall

Thickness

No Spacer ½”

½” ⁄”

¾” 1”

1” 1¼”

Junction Box

Screws

3Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JAN 2023 G0

modernforms.com

Phone (800) 526.2588

Fax (800) 526.2585

Headquarters/Eastern Distribution Center

44 Harbor Park Drive

Port Washington, NY 11050

Central Distribution Center

1600 Distribution Ct

Lithia Springs, GA 30122

Western Distribution Center

1750 Archibald Avenue

Ontario, CA 91760