TP-LINK tp-link Archer TXE70UH AXE5400 WiFi 6E High Gain Wireless USB Adapter Mode d'emploi

Marque: TP-LINK

Modèle: tp-link Archer TXE70UH AXE5400 WiFi 6E High Gain Wireless USB Adapter

Taper: Mode d'emploi

User Guide

AXE5400 Wi-Fi 6E High Gain Wireless USB Adapter

Archer TXE70UH

Contents

About This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Chapter 1. Get to Know About Your Adapter . . . . . . . . . . . . . . . . . . . . .2

1. 1. Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1. 2. LED Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Chapter 2. Use the Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

2. 1. Install Driver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2. 2. Join a Wireless Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2. 3. Uninstall Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Appendix: Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

About This Guide

This guide is a complement to Quick Installation Guide. The Quick Installation

Guide instructs you on quick installation, and this guide provides the product

overview and detailed instructions for each steps.

When using this guide, please notice that features available of the adapter may

vary by model and software version. It may also vary by region or ISP. All images,

steps, and descriptions in this guide are only examples and may not reflect your

actual experience.

Conventions

In this guide, the following conventions are used:

Convention Description

Underlined Underlined words or phrases are hyperlinks. You can click to redirect to a

website or a specific section.

Teal Contents to be emphasized and texts on the web page are in teal, including

the menus, items, buttons, etc.

Note: Ignoring this type of note might result in a malfunction or damage to the

device.

Tips: Indicates important information that helps you make better use of your

device.

*Maximum wireless signal rates are the physical rates derived from IEEE Standard 802.11 specifications.

Actual wireless data throughput , wireless coverage, and number of connected devices are not guaranteed

and will vary as a result of network conditions, AP limitations, and environmental factors, including building

materials, obstacles, volume and density of traffic, and AP location.

*Use of Wi-Fi 6 (802.11ax), Wi-Fi 6E, and features including OFDMA, MU-MIMO, Beamforming, 1024-QAM,

or HE160 require APs to also support the corresponding features.

*Functionality of Archer TXE70UH may be restricted on some operating systems and platforms. Please try

to update the device’s driver for feature compatibility.

*Use of WPA3 requires APs to also support the corresponding feature.

More Info

• The latest driver can be found at Download Center

at https://www.tp-link.com/support.

• The Quick Installation Guide can be found where you find this guide or inside

the package of the router.

• Specifications can be found on the product page at https://www.tp-link.com.

• A TP-Link Community is provided for you to discuss our products at

https://community.tp-link.com.

• Our Technical Support contact information can be found at the Contact

Technical Support page at https://www.tp-link.com/support.

Chapter 1

Get to Know About Your

Adapter

This chapter introduces what the adapter can do and shows its appearance.

This chapter contains the following sections:

• Product Overview

• LED Status

Chapter 1 Get to Know about Your Adapter

1. 1. Product Overview

TP-Link Wireless USB Adapter connects your computer to a Wi-Fi network for

smooth HD video, voice streaming and online gaming.

• The high-gain antennas greatly enhance the reception and transmission signal

strength of the USB adapter.

• Utilizes 802.11ax standard and is backward compatible with 802.11a/b/g/n/ac*.

• Supports WEP, WPA/WPA2/WPA3, WPA-PSK/ WPA2-PSK*.

• Supports Windows 10(32-bit), Windows 10/11(64-bit)*.

1. 2. LED Status

You can check the adapter’s working status by following the LED explanation

table.

Status Indication

On The driver has been installed successfully.

Off The driver is not installed.

The adapter is not detected.

Tips:

If the LED is off, try these troubleshooting tips:

1. Check if the adapter is recognized and enabled or not. Refer to Appendix: Troubleshooting for detailed

instructions.

2. Remove and reinsert the adapter.

3. Reinstall the software, if necessary.

Chapter 2

Use the Adapter

This chapter introduces how to install your adapter’s driver, use your adapter

to join a wireless network, and uninstall your adapter in a Windows system.

The adapter is equipped with a Setup Wizard, which can guide you through the

installation process.

This chapter includes the following sections:

• Install Driver

• Join a Wireless Network

• Uninstall Driver

Chapter 2 Use the Adapter

2. 1. Install Driver

1. Go to My Computer or This PC.

2. Double click the TP-Link CD ROM then run SetupInstall.exe to install driver.

Note:

1. If you cannot find the setup program, please download the driver at www.tp-link.com/support.

2. If an unknown publisher message pops up, select Yes to continue.

3. If Windows User Account Control requires admin credentials, type user name and password of

your Windows administrator account. .

2. 2. Join a Wireless Network

You can join a wireless network via Windows built-in wireless utility. Follow the

instructions below to use your computer system’s built-in wireless utility:

Click the Network icon on the taskbar. Select the Wi-Fi network you want to join,

and click Connect. Enter the network password when prompted.

2. 3. Uninstall Driver

The software uninstallation steps vary a bit from different systems. Here we take

the instructions for Windows 10 as an example.

Go to Contol Pannel > Programs, click Uninstall a program, then double-click

TP-

Link

Archer TXE70UH Driver, then follow the on-screen instructions to complete

the uninstallation.

SetupInstall.exe

Appendix: Troubleshooting

T1. What should I do if the adapter is not detected?

• Make sure the adapter is securely connected to the computer.

• Make sure you meet the minimum system requirements for the adapter and that the

latest Windows and system updates are installed on your computer.

• Make sure you use the latest driver for your specific adapter. The latest drivers can

be found at https://www.tp-link.com/download-center.

• Try a different USB port on the computer.

• Try restarting the computer or try using the adapter on a different computer.

T2. How to check if I have installed the driver for my adapter successfully

or not?

1. On your computer, please right click Computer icon and go to Manage;

2. Open the Device Manager and go to Network adapters, and then find the

corresponding TP-Link adapter, right click it and then go to Properties;

3. If you can see “This device is working properly.” in the red box, you have already

installed the driver successfully.

T3. What should I do if can’t connect to the Wi-Fi after installing the

driver?

• Refer to T2 to check if you have installed the driver for your adapter successfully .

• Make sure the adapter is securely connected to the computer.

• Disable the antivirus software and firewall, then try again.

• Try a different USB port on the computer.

• Restart your computer and try again.

• Re-install the driver and try again.

T4. How to find the hardware version of the adapter?

• The hardware version is printed on the product label on the package or the adapter.

There is a character string “Ver:X.Y” (for example, Ver:2.0) in the Serial Number field,

and the number X is the hardware version of the adapter.

• Visit https://www.tp-link.com/faq-46.html and follow the second method to find the

hardware version of the adapter.

For more detailed instructions:

• Can’t find the hardware version of the adapter: https://www.tp-link.com/faq-46.html

• Can’t find or join the wireless networks: https://www.tp-link.com/faq-2253.html

• Can’t install the driver: https://www.tp-link.com/faq-2252.html

FCC compliance information statement

Product Name: AXE5400 Wi-Fi 6E High Gain Wireless USB Adapter

Model Number: Archer TXE70UH

Responsible party:

TP-Link USA Corporation

Address: 10 Mauchly, Irvine, CA 92618

Website: https://www.tp-link.com/us/

Tel: +1 626 333 0234

Fax: +1 909 527 6804

E-mail: [email protected]om

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions:

1 ) This device may not cause harmful interference.

2 ) This device must accept any interference received, including interference

that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible

for compliance could void the user’s authority to operate the equipment.

Note: The manufacturer is not responsible for any radio or TV interference

caused by unauthorized modifications to this equipment. Such modifications

could void the user’s authority to operate the equipment.

FCC RF Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for

an uncontrolled environment. End users must follow the specific operating

instructions for satisfying RF exposure compliance. This transmitter must not

be co-located or operating in conjunction with any other antenna or transmitter.

This equipment has been SAR-evaluated for use in hand. SAR measurements

are based on a 5mm spacing from the body and that compliance is achieved at

that distance.

FCC regulations restrict operation of this device to indoor use only. The

operation of this device is prohibited on oil platforms, cars, trains, boats, and

aircraft, except that operation of this device is permitted in large aircraft while

flying above 10000 feet. Operation of transmitters in the 5.925-7.125 GHz band

is prohibited for control of or communications with unmanned aircraft systems.

We, TP-Link USA Corporation, has determined that the equipment shown as

above has been shown to comply with the applicable technical standards, FCC

part 15. There is no unauthorized change is made in the equipment and the

equipment is properly maintained and operated.

Issue Date: 2022.06.30

CE Mark Warning

This is a class B product. In a domestic environment, this product may cause

radio interference, in which case the user may be required to take adequate

measures.

OPERATING FREQUENCY (the maximum transmitted power)

2400MHz-2483.5MHz(15dBm)

5150MHz-5250MHz(15dBm)

5250MHz-5350MHz(15dBm)

5470MHz-5725MHz(16dBm)

5945MHz-6425MHz(16dBm)

EU declaration of conformity

TP-Link hereby declares that the device is in compliance with the essential

requirements and other relevant provisions of directives 2014/53/EU, 2011

/65/EU and (EU) 2015/863.

The original EU declaration of conformity may be found

at https://www.tp-link.com/en/support/ce/

UK declaration of conformity

TP-Link hereby declares that the device is in compliance with the essential

requirements and other relevant provisions of the Radio Equipment Regulations

2017.

The original UK declaration of conformity may be found at https://www.tp-link.

com/support/ukca/

RF Exposure Information

The device complies with RF specifications when the device used at 20 cm from

your body.

Attention: This device may only be used indoors in all EU member states, EFTA

countries and Northern Ireland.

Frequency band: 5150 - 5250 MHz:

Indoor use: Inside buildings only. Installations and use inside road vehicles

and train carriages are not permitted. Limited outdoor use: If used outdoors,

equipment shall not be attached to a fixed installation or to the external body of

road vehicles, a fixed infrastructure or a fixed outdoor antenna. Use by unmanned

aircraft systems (UAS) is limited to within the 5170 - 5250 MHz band.

Frequency band: 5250 - 5350 MHz:

Indoor use: Inside buildings only. Installations and use in road vehicles, trains

and aircraft are not permitted. Outdoor use is not permitted.

Frequency band: 5470 - 5725 MHz:

Installations and use in road vehicles, trains and aircraft and use for unmanned

aircraft systems (UAS) are not permitted.

AT BE BG CH CY CZ DE DK

EE EL ES FI FR HR HU IE

IS IT LI LT LU LV MT NL

NO PL PT RO SE SI SK UK(NI)

Attention: This device may only be used indoors in Great Britain.

Canadian Compliance Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with

Innovation, Science and Economic Development Canada’s licence-exempt

RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may

cause undesired operation of the device.

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est

conforme aux CNR d’Innovation, Sciences et Développement économique

Canada applicables aux appareils radio exempts de licence. L’exploitation est

autorisée aux deux conditions suivantes :

1) L’appareil ne doit pas produire de brouillage;

2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le

brouillage est susceptible d’en compromettre le fonctionnement.

Caution: The device for operation in the band 5150–5250 MHz is only for

indoor use to reduce the potential for harmful interference to co-channel mobile

satellite systems.

DFS (Dynamic Frequency Selection) products that operate in the bands 5250-

5350 MHz, 5470-5600MHz, and 5650-5725MHz.

ISED regulations restrict operation of this device to indoor use only. The

operation of this device is prohibited on oil platforms, cars, trains, boats, and

aircraft, except that operation of this device is permitted in large aircraft while

flying above 10000 feet. Operation of transmitters in the 5.925-7.125 GHz band

is prohibited for control of or communications with unmanned aircraft systems.

Les réglementations ISED limitent le fonctionnement de cet appareil à une

utilisation en intérieur uniquement. L’utilisation de cet appareil est interdite sur

les plates-formes pétrolières, les voitures, les trains, les bateaux et les avions,

sauf que l’utilisation de cet appareil est autorisée dans les avions long courrier

en vol au-dessus de 10 000 pieds. L’exploitation d’émetteurs dans la bande

5,925-7,125 GHz est interdite pour le contrôle ou les communications avec des

systèmes d’avions sans pilote.

Avertissement:

1 ) Le dispositif fonctionnant dans la bande 5150-5250 MHz est réservé

uniquement pour une utilisation à l’intérieur afin de réduire les risques de

brouillage préjudiciable aux systèmes de satellites mobiles utilisant les

mêmes canaux;

2 ) Le gain maximal d’antenne permis pour les dispositifs avec antenne(s)

amovible(s) utilisant les bandes 5250-5350 MHz et 5470-5725 MHz doit

se conformer à la limitation P.I.R.E.;

3 ) Le gain maximal d’antenne permis pour les dispositifs avec antenne(s)

amovible(s) utilisant la bande 5725-5850 MHz doit se conformer à la

limitation P.I.R.E spécifiée pour l’exploitation point à point et non point à

point, selon le cas.

Les produits utilisant la technique d’atténuation DFS (sélection dynamique des

fréquences) sur les bandes 5250- 5350 MHz, 5470-5600MHz et 5650-5725MHz.

Radiation Exposure Statement:

This EUT is compliance with SAR for general population/uncontrolled exposure

limits in RSS-102 and had been tested in accordance with the measurement

methods and procedures specified in IEEE 1528 and IEC 62209. This equipment

should be installed and operated with minimum distance 0.5 cm between the

radiator and your body. This device

and its antenna(s) must not be co-located or operating in conjunction with any

other antenna or transmitter.

Déclaration d’exposition aux radiations :

Cet adaptateur est conforme au SAR pour la population générale/limites

d’exposition non contrôlées dans RSS-102 et a été testé conformément aux

méthodes et procédures de mesure spécifiées dans IEEE 1528 et CEI 62209.

Cet équipement doit être installé et utilisé avec une distance minimale de 5 mm

entre le radiateur et votre corps. Cet appareil et ses antennes ne doivent pas

être situés ou fonctionner en conjonction avec une autre antenne ou un autre

émetteur.

Industry Canada Statement

CAN ICES-3 (B)/NMB-3(B)

Korea Warning Statements

당해 무선설비는 운용중 전파혼신 가능성이 있음.

NCC Notice

注意！

取得審驗證明之低功率射頻器材，非經核准，公司、商號或使用者均不得擅自變

更頻率、加大功率或變更原設計之特性及功能。

低功率射頻器材之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象

時，應立即停用，並改善至無干擾時方得繼續使用。

前述合法通信，指依電信管理法規定作業之無線電通信。

低功率射頻器材須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干

擾。

應避免影響附近雷達系統之操作。

高增益指向性天線只得應用於固定式點對點系統。

BSMI Notice

安全諮詢及注意事項

• 請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。

• 清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。

• 注意防潮，請勿將水或其他液體潑灑到本產品上。

• 插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋

開口。

• 請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位

置中。

• 請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項

工作。

限用物質含有情況標示聲明書

產品元件

名稱

限用物質及其化學符號

鉛

鎘

汞

六價鉻

Cr+6

多溴聯苯

PBB

多溴二苯醚

PBDE

PCB ○ ○ ○ ○ ○ ○

外殼 ○ ○ ○ ○ ○ ○

其他及其

配件一○○○○ ○

備考1.“超出0.1wt%”及“超出0.01wt%”系指限用物質之百分比含量超出百分比含量基準

值。

備考2. “○”系指該項限用物質之百分比含量未超出百分比含量基準值。

Продукт сертифіковано згідно с правилами системи УкрСЕПРО

на відповідність вимогам нормативних документів та вимогам, що

передбачені чинними законодавчими актами України.

Safety Information

• Keep the device away from water, fire, humidity or hot environments.

• Do not attempt to disassemble, repair, or modify the device. If you need service,

please contact us.

• Do not use the device where wireless devices are not allowed.

• This product can be powered only by computers that comply with Power

Source Class 2 ( PS2) or Limited Power Source(LPS) of IEC 62368-1.

• This product uses radios and other components that emit electromagnetic fields.

Electromagnetic fields and magnets may interfere with pacemakers and other

implanted medical devices. Always keep the product and its power adapter more

than 15 cm (6 inches) away from any pacemakers or other implanted medical

devices. If you suspect your product is interfering with your pacemaker or any

other implanted medical device, turn off your product and consult your physician

for information specific to your medical device.

Operating Temperature: 0℃~40℃ (32°F~104°F)

Please read and follow the above safety information when operating the device.

We cannot guarantee that no accidents or damage will occur due to improper use

of the device. Please use this product with care and operate at your own risk.

Attention: This device may only be used indoors in all EU member states and EFTA

countries.

Explanation of the symbols on the product label

Symbols may vary from products.

Symbol Explanation

Class II equipment

Class II equipment with functional earthing

Alternating current

DC voltage

Polarity of output terminals

Indoor use only

Dangerous voltage

Caution, risk of electric shock

Energy efficiency Marking

Protective earth

Earth

Frame or chassis

Functional earthing

Caution, hot surface

Caution

Operator’s manual

Stand-by

“ON”/”OFF” (push-push)

Fuse

Fuse is used in neutral N

RECYCLING

This product bears the selective sorting symbol for Waste

electrical and electronic equipment (WEEE). This means

that this product must be handled pursuant to European

directive 2012/19/EU in order to be recycled or dismantled

to minimize its impact on the environment.

User has the choice to give his product to a competent

recycling organization or to the retailer when he buys a new

electrical or electronic equipment.

Caution, avoid listening at high volume levels for long

periods

Disconnection, all power plugs

m Switch of mini-gap construction

Switch of micro-gap construction (for US version)

Switch of micro-gap / micro-disconnection construction (for

other versions except US)

εSwitch without contact gap (Semiconductor switching

device)

TP-LINK tp-link Archer TXE70UH AXE5400 WiFi 6E High Gain Wireless USB Adapter Mode d'emploi

Marque: TP-LINK

Modèle: tp-link Archer TXE70UH AXE5400 WiFi 6E High Gain Wireless USB Adapter

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: TP-LINK tp-link Archer TXE70UH AXE5400 WiFi 6E High Gain Wireless USB Adapter User guide

Documents connexes

Autres documents

Vuzix 492 Manuel utilisateur