Honeywell PROWIFI Guide d'installation

Marque: Honeywell

Modèle: PROWIFI

Taper: Guide d'installation

PROWIFI

Wireless Communication Module

Installation and Setup Guide

GENERAL INFORMATION

The PROWIFI Wireless Communication Module provides PRO Series Control Panels with a Wi-Fi

connection and permits them to

communicate with the Central Station and PRO Series Wireless Touchscreens via Wi-Fi. The module connects directly to the Control

Panel and is powered via the Control Panel’s connection. Refer to the applicable Control Panel's Installation and Setup Guide for

additional information.

INSTALLING THE MODULE

Ensure that all electrical power is removed from the control before installing the module. Unplug the

power supply and disconnect the backup battery.

1. Affix the provided FCC/IC label (P/N R800-

26437A for the PROWIFI) on the control’s

case back (refer to Figure 1).

2. If the Control Panel is not powered up

proceed to step 7. If the Control Panel is

powered up, disarm the system and wait 30-

60 seconds:

3. Unplug the power supply.

4. Remove the screw securing the control to the

wall or desk mount.

5. Remove the control from the wall or desk

mount.

6. Disconnect the battery.

QS-162-V0

Figure 1. FCC/IC Label Location

7. Remove the left side cover from the control.

8. Insert the PROWIFI module into the slot on

the left side of the control as shown in Figure

2 and ensure the receptacle is securely

seated on the control’s edge connector.

9. Secure with the screw.

10. Install the left side cover.

11. Connect the battery.

12. Install the control on the wall or desk mount.

13. Plug the power supply into a 24-hour,

110VAC unswitched outlet.

QS-058-V1

COVER

PROWIFI

MODULE

SCREW

Figure 2. Installing the PROWIFI Module

Programming

Note: The PROWIFI requires a router and internet service for Wi-Fi connection.

1. Programming associated with the PROWIFI module is conducted through the AlarmNet 360™ Programming Tool. On a laptop, PC or

Smart Device, go to www.alarmnet360.com.

2. When programming is complete, perform a Communications Test.

SPECIFICATIONS

Board Dimensions: ............................................................................................................................................... 1.625” W x 2.625” L x 0.3125” D

Input Voltage Range: .............................................................................................................................................................. 3.6 – 14V, Max 17V

Input Voltage: .................................................................................................................................................................................................. 3.5V

Current Drain: ............................................................................................................................................................................................. 250mA

Temperature: ............................................................................................................................................................... 32°F (0°C) to 140°F (60°C)

REFER TO THE INSTALLATION AND SETUP GUIDE FOR THE CONTROL WITH WHICH THIS DEVICE IS USED FOR WARRANTY

INFORMATION AND LIMITATIONS OF THE ENTIRE SYSTEM.

FEDERAL COMMUNICATIONS COMMISSION & ISED STATEMENTS

The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User's Manual. Unauthorized changes or

modifications could void the user's authority to operate the equipment.

FCC CLASS B STATEMENT

This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following statement for your information:

This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer's instructions, may cause

interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in

Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• If using an indoor antenna, replace it with a quality outdoor antenna.

• Reorient the receiving antenna until interference is reduced or eliminated.

• Move the radio or television receiver away from the receiver/control.

• Move the antenna leads away from any wire runs to the receiver/control.

• Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits.

• Consult the dealer or an experienced radio/TV technician for help.

Responsible Party / Issuer of Supplier’s Declaration of Conformity: Ademco Inc., a subsidiary of Resideo Technologies, Inc., 2 Corporate Center Dr., Melville, NY 11747, Ph:

516-577-2000.

ISED CLASS B STATEMENT

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

FCC / ISED STATEMENT

This device complies with Part 15 of the FCC Rules, and ISED’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause

harmful interference (2) This device must accept any interference received, including interference that may cause undesired operation.

Cet appareil est conforme à la partie 15 des règles de la FCC et exempt de licence RSS d’ISED. Son fonctionnement est soumis aux conditions suivantes: (1) Cet appareil ne

doit pas causer d’interférences nuisibles. (2) Cet appareil doit accepter toute interférence reçue y compris les interférences causant une réception indésirable.

RF Exposure Warning

The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 7.8 inches (20 cm) from all persons and

must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC and ISED multi-

transmitter product procedures.

Mise en Garde

Exposition aux Frequences Radio: La/les antenne(s) utilisée(s) pour cet émetteur doit/doivent être installée(s) à une distance de séparation

d'au moins 20 cm (7,8 pouces) de toute personne et ne pas être située(s) ni fonctionner parallèlement à tout autre transmetteur ou antenne,

excepté en conformité avec les procédures de produit multi transmetteur FCC et ISEDs.

The product should not be disposed of with other household waste. Check for the nearest authorized collection centers or authorized recyclers. The correct disposal

of end-of-life equipment will help prevent potential negative consequences for the environment and human health.

Any attempt to reverse-engineer this device by decoding proprietary protocols, de-compiling firmware, or any similar actions is strictly prohibited.

SUPPORT & WARRANTY INFORMATION

For the latest documentation and support, please go to:

www.resideo.com

For the latest warranty information, please go to:

www.security.honeywellhome.com/warranty

The Honeywell Home Trademark is used under license from Honeywell International Inc.

This product manufactured by Resideo Technologies, Inc. and its affiliates

2 Corporate Center Drive, Suite 100

P.O. Box 9040, Melville, NY 11747

 2020 Resideo Technologies, Inc.