Skil ID6744A-00 Le manuel du propriétaire

WARNING: To reduce the risk of injury, the user must read and understand the

Owner’s Manual before using this product. Save these instructions for future reference.

AVERTISSEMENT : Afin de réduire les risques de blessure, l’utilisateur doit lire et

comprendre le guide d’utilisation avant d’utiliser cet article. Conservez le présent guide

afin de pouvoir le consulter ultérieurement.

ADVERTENCIA : Para reducir el riesgo de lesiones, el usuario debe leer y comprender

el Manual del operador antes de utilizar este producto. Guarde estas instrucciones para

consultarlas en caso sea necesario.

Owner’s Manual

Guide d’utilisation

Manual del propietario

For Customer Service

Pour le service à la clientèle

Servicio al cliente

12V Brushless Impact Driver

Visseuse à percussion sans balais de 12 V

Atornillador de impacto de 12 V sin escobillas

Model/ Modelo/ Modèle: ID6744A-00

BRUSHLESS

12

1-877-SKIL-999 OR www.skil.com

TM

2

TABLE OF CONTENTS

General Power Tool Safety Warnings . ............................3-5

Safety Warnings for Impact Driver ..................................5

Symbols .....................................................6-9

Get to Know Your Impact Driver ..................................10

Specications .................................................10

Operating Instructions .......................................11-17

Maintenance ...................................................18

Troubleshooting ...............................................18

Limited Warranty of SKIL Cordless Tool ............................19

WARNING

• Some dust created by power sanding, sawing, grinding, drilling and other construction

activities contains chemicals known to the State of California to cause cancer, birth defects

or other reproductive harm. Some examples of these chemicals are:

– Lead from lead-based paints.

– Crystalline silica from bricks, cement, and other masonry products.

– Arsenic and chromium from chemically-treated lumber.

• Your risk from these exposures varies, depending upon how often you do this type of work.

To reduce your exposure to these chemicals:

– Work in a well-ventilated area.

– Work with approved safety equipment, such as dust masks that are specially designed to

lter out microscopic particles.

– Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and

other construction activities. Wear protective clothing and wash exposed areas with soap

and water. Allowing dust to get into your mouth or eyes or to lie on the skin may promote

absorption of harmful chemicals.

3

GENERAL POWER TOOL SAFETY WARNINGS

WARNING

Read all safety warnings, instructions, illustrations and specications

provided with this power tool. Failure to follow all instructions listed

below may result in electric shock, re and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE

REFERENCE.

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

Work area safety

Keep work area clean and well lit. Cluttered or dark areas invite accidents.

Do not operate power tools in explosive atmospheres, such as in the presence of

ammable liquids, gases or dust. Power tools create sparks which may ignite the dust or

fumes.

Keep children and bystanders away while operating a power tool. Distractions can cause

you to lose control.

Electrical safety

Power tool plugs must match the outlet. Never modify the plug in any way. Do not use

any adapter plugs with earthed (grounded) power tools. Unmodied plugs and matching

outlets will reduce risk of electric shock.

Avoid body contact with earthed or grounded surfaces, such as pipes, radiators,

ranges and refrigerators. There is an increased risk of electric shock if your body is earthed

or grounded.

Do not expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock.

Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled

cords increased the risk of electric shock.

When operating a power tool outdoors, use an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the risk of electric shock.

If operating a power tool in a damp location is unavoidable, use a ground fault circuit

interrupter (GFCI)” protected supply. Use of a GFCI reduces the risk of electric shock.

Personal safety

Stay alert, watch what you are doing and use common sense when operating a power

tool. Do not use a power tool while you are tired or under the inuence of drugs,

alcohol or medication. A moment of inattention while operating power tools may result in

serious personal injury.

Use personal protective equipment. Always wear eye protection. Protective equipment

such as dust mask, non-skid safely shoes, hard hat or hearing protection used for appropriate

conditions will reduce personal injuries.

Prevent unintentional starting. Ensure the switch is in the off-position before

connecting to power source and/or battery pack, picking up or carrying the tool.

Carrying power tools with your nger on the switch or energizing power tools that have the

switch on invites accidents.

Remove any adjusting key or wrench before turning the power tool on. A wrench or a

key left attached to a rotating part of the power tool may result in personal injury.

4

Do not overreach. Keep proper footing and balance at all times. This enables better

control of the power tool in unexpected situations.

Dress properly. Do not wear loose clothing or jewelry. Keep your hair and clothing

away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.

If devices are provided for the connection of dust extraction and collection facilities,

ensure these are connected and properly used. Use of dust collection can reduce dust-

related hazards.

Do not let familiarity gained from frequent use of tools allow you to become complacent

and ignore tool safety principles. A careless action can cause severe injury within a fraction

of a second.

Power tool use and care

Do not force the power tool. Use the correct power tool for your application. The correct

power tool will do the job better and safer at the rate for which it was designed.

Do not use the power tool if the switch does not turn it on and off. Any power tool that

cannot be controlled with the switch is dangerous and must be repaired.

Disconnect the plug from the power source and/or remove the battery pack, if

detachable, from the power tool before making any adjustments, changing accessories,

or storing power tools. Such preventive safely measures reduce the risk of starting the

power tool accidentally.

Store idle power tools out of the reach of children and do not allow persons unfamiliar

with the power tool or these instructions to operate the power tool. Power tools are

dangerous in the hands of untrained users.

Maintain power tools and accessories. Check for misalignment or binding of moving

parts, breakage of parts and any other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired before use. Many accidents are caused

by poorly maintained power tools.

Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

Use the power tool, accessories and tool bits etc. in accordance with these instructions,

taking into account the working conditions and the work to be performed. Use of the

power tool for operations different from those intended could result in a hazardous situation.

Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery

handles and grasping surfaces do not allow for safe handling and control of the tool in

unexpected situations.

Battery tool use and care

Recharge only with the charger specied by the manufacturer. A charger that is suitable

for one type of battery pack may create a risk of re when used with another battery pack.

Use power tools only with specically designated battery packs. Use of any other battery

packs may create a risk of injury and re.

When battery pack is not in use, keep it away from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal objects, that can make a connection

from one terminal to another. Shorting the battery terminals together may cause burns or a

re.

Under abusive conditions, liquid may be ejected from the battery; avoid contact. If

contact accidentally occurs, ush with water. If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery may cause irritation or burns.

Do not use a battery pack or tool that is damaged or modied. Damaged or modied

batteries may exhibit unpredictable behavior resulting in re, explosion or risk of injury.

5

Do not expose a battery pack or tool to re or excessive temperature. Exposure to re or

temperature above 265°F (130°C) may cause explosion.

Follow all charging Instructions and do not charge the battery pack or tool outside the

temperature range specied in the instructions. Charging improperly or at temperatures

outside the specied range may damage the battery and increase the risk of re.

Service

Have your power tool serviced by a qualied repair person using only identical

replacement parts. This will ensure that the safety of the power tool is maintained.

Never service damaged battery packs. Service of battery packs should only be performed

by the manufacturer or authorized service providers.

SAFETY WARNING FOR IMPACT DRIVER

Hold the power tool by insulated gripping surfaces, when performing an operating

where the fastener may contact hidden wiring. Fasteners contacting a “live” wire may

make exposed metal parts of the power tool “live” and could give the operator an electric

shock.

6

SYMBOLS

Safety Symbols

The purpose of safety symbols is to attract your attention to possible dangers. The safety

symbols and explanations with them deserve your careful attention and understanding. The

symbol warnings do not, by themselves, eliminate any danger. The instructions and warnings

they give are no substitutes for proper accident prevention measures.

WARNING

Be sure to read and understand all safety instructions in this Owner's

Manual, including all safety alert symbols such as “DANGER,”

“WARNING,” and “CAUTION” before using this tool. Failure to following all instructions listed

below may result in electric shock, re, and/or serious personal injury.

The denitions below describe the level of severity for each signal word. Please read the manual

and pay attention to these symbols.

This is the safety alert symbol. It is used to alert you to potential

personal injury hazards. Obey all safety messages that follow this

symbol to avoid possible injury or death.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION

CAUTION, used with the safety alert symbol, indicates a hazardous

situation which, if not avoided, will result in minor or moderate injury.

Damage Prevention and Information Messages

These inform the user of important information and/or instructions that could lead to equipment

or other property damage if they are not followed. Each message is preceded by the word

“NOTICE”, as in the example below:

NOTICE: Equipment and/or property damage may result if these instructions are not followed.

WARNING

The operation of any power tools can result in foreign

objects being thrown into your eyes, which can result

in severe eye damage. Before beginning power tool operation, always

wear safety goggles or safety glasses with side shields and a full face

shield when needed. We recommend a Wide Vision Safety Mask for use

over eyeglasses or standard safety glasses with side shields. Always use

eye protection which is marked to comply with ANSI Z87.1.

7

SYMBOLS (CONTINUED)

IMPORTANT: Some of the following symbols may be used on your tool. Please study them

and learn their meaning. Proper interpretation of these symbols will allow you to operate the

tool better and more safely.

Symbol Name Designation/Explanation

V Volts Voltage (potential)

AAmperes Current

Hz Hertz Frequency (cycles per second)

WWatt Power

kg Kilograms Weight

min Minutes Time

s Seconds Time

Wh Watt-hours Battery capacity

Ah Ampere-Hours Battery capacity

ØDiameter Size of drill bits, grinding wheels, etc.

n0No-load speed Rotational speed, at no load

nRated speed Maximum attainable speed

…/min Revolutions or

reciprocations per minute Revolutions, strokes, surface speed,

orbits, etc. per minute

0 Off position Zero speed, zero torque...

1,2,3,…

I,II,III, Selector settings Speed, torque or position settings. Higher

number means greater speed

Innitely variable selector

with off Speed is increasing from 0 setting

Arrow Action in the direction of arrow

Alternating current Type or a characteristic of current

Direct current Type or a characteristic of current

Alternating or direct current Type or a characteristic of current

Class II construction Designates Double Insulated Construction

tools.

Earthing terminal Grounding terminal

Li-ion RBRC seal Designates Li-ion battery recycling

program

8

Symbol Name Designation/Explanation

Ni-Cad RBRC seal Designates Ni-Cad battery recycling

program

Read manual symbol Alerts user to read manual

Wear eye protection symbol Always wear safety goggles or safety

glasses with side shields and a full face

shield when operating this product.

Always operate with two

hands Alerts user to always operate with two

hands

Do not use the guard for cut-

off operations Alerts user not to use the guard for cut-off

operations

9

SYMBOLS (CERTIFICATION INFORMATION)

IMPORTANT: Some of the following symbols for certication information may be used on your

tool. Please study them and learn their meaning. Proper interpretation of these symbols will

allow you to operate the tool better and more safely.

Symbol Designation/Explanation

This symbol designates that this tool is listed by Underwriters Laboratories.

This symbol designates that this component is recognized by

Underwriters Laboratories.

This symbol designates that this tool is listed by Underwriters

Laboratories, to United States and Canadian Standards.

This symbol designates that this tool is listed by the Canadian

Standards Association.

This symbol designates that this tool is listed by the Canadian

Standards Association, to United States and Canadian Standards.

This symbol designates that this tool is listed by the Intertek Testing

Services, to United States and Canadian Standards.

10

GET TO KNOW YOUR IMPACT DRIVER

12V Brushless Impact Driver

BRUSHLESS

12

Fig. 1

LED Light

One Hand Collet

Variable-Speed

Trigger Switch

LED Light Button

Mode Button

Removable Belt Clip

Strap Fixing Area

Bit Sorage Area

Direction-of-Rotation

(forward/center-lock/

reverse) Selector

SPECIFICATIONS

Rated Voltage 12V d.c.

Collet size 1/4 in. (6.35mm) (one hand collet)

No-load Speed (n0) 0-1450 / 0-2100 / 0-2900 /min (RPM)

Impact rate 0-1450 / 0-3000 / 0-3600 /min (IPM)

Recommended Operating Temperature 14 – 104°F (-10 – 40oC)

Recommended Storage Temperature 32 – 104°F (0 – 40oC)

11

OPERATING INSTRUCTIONS

WARNING

To reduce the risk of re, personal injury, and product damage due to

a short circuit, never immerse your tool, battery pack or charger in

uid or allow a uid to ow inside them. Corrosive or conductive uids, such as seawater,

certain industrial chemicals, and bleach or bleach-containing products, etc, can cause a short

circuit.

WARNING

If any parts are damaged or missing, do not operate this product until

the parts are replaced. Use of this product with damaged or missing parts

could result in serious personal injury.

WARNING

Do not attempt to modify this impact driver or create accessories not

recommended for use with this impact driver. Any such alteration or

modication is misuse and could result in a hazardous condition leading to possible serious

injury.

WARNING

To prevent accidental starting that could cause serious personal

injury, always remove the battery pack from the impact driver when

assembling parts.

This cordless impact driver must be used only with the battery packs and charger listed

below:

Battery Pack Charger

2Ah 4Ah

SKIL BY500101

SKIL BY519901 SKIL BY519801 SKIL QC535701

SKIL SC536501

NOTICE: Please refer to the battery and charger manual for detailed operating information.

To Attach/Detach Battery Pack

(Fig. 2)

Lock the variable-speed trigger switch “OFF”

on the tool by placing the direction-of-rotation

(forward/center-lock/reverse) selector in the

center position before attaching or detaching

the battery pack.

To attach the battery pack:

Align the raised rib on the batter pack with the

grooves on the tool, and then slide the battery

pack onto the tool.

NOTICE: When placing the battery pack on the

tool, be sure that the raised rib on the battery

pack aligns with the groove inside the tool

and that the latches snap into place properly.

Improper attachment of the battery pack can cause damage to internal components.

To detach the battery pack:

Depress the battery-release button, located on the front of the battery pack, to release the

battery pack. Pull the battery pack out and remove it from the tool.

WARNING

Battery tools are always in operating condition. Therefore, the Direc-

tion-of-Rotation (forward/center-lock/reverse) Selector should always

be locked in center position when not in use or carrying at your side.

BRUSHLESS

12

Fig. 2

Attach

Battery-Release

Button

Detach

12

Direction-of-Rotation (Forward/Center-Lock/Reverse) Selector

WARNING

After tool use, lock the direction-of-rotation selector in the “OFF”

position (center-lock) to help prevent accidental starts and injury.

Your tool is equipped with a direction-of-rotation selector, located above the variable-speed

trigger switch. This selector is used to change the direction of rotation of the bit and to lock the

variable-speed trigger in the “OFF” (center-lock) position (Fig. 3).

a. Position the direction-of-rotation selector to the far left of the tool for forward rotation to drive

the screws in.

b. Position the direction-of-rotation selector to the far right of the tool for reverse rotation to

remove screws.

c. Position the switch in the “OFF” (center-lock) position to help reduce the possibility of

accidental starting when the tool is not in use.

NOTICE: To prevent gear damage, always allow the impact driver to come to a complete stop

before changing the direction of rotation.

NOTICE: The impact driver will not run unless the direction-of-rotation selector is engaged

fully to the left or to the right.

Fig. 3

Center-Lock ReverseForward

13

Variable-Speed Trigger Switch

Your tool is equipped with a variable-speed

trigger switch. The tool can be turned “ON”

or “OFF” by depressing or releasing the vari-

able-speed trigger switch.

The variable-speed trigger switch delivers high-

er speed with increased trigger pressure and

lower speed with decreased trigger pressure

(Fig. 4).

LED Light

Your tool is equipped with an LED light, located

on the head of the tool. This provides addition-

al light without shadows on the surface of the

work piece for operation in lower-light areas.

To turn on the LED light:

• The LED light will automatically turn on with a

slight squeeze on the variable-speed trigger

switch before the tool starts running.

• The LED light could be turned on manually

by pressing the LED light button.

To turn off the LED light:

• The LED light could be turned off manually

by pressing the LED light button after the

variable speed trigger switch is released.

• The LED light will turn off approximately 10 seconds after the variable speed trigger switch is

released without pressing the LED light button.

• The LED light will turn off approximately 10 minutes after turning on the LED light by

pressing the LED light button without squeezing on the variable-speed trigger switch.

NOTICE: The LED light button is disabled when the motor is running.

When the tool and/or battery pack becomes overloaded or too hot, the internal sensors will

turn the tool off. If the tool and/or battery pack are overloaded, the LED light will ash rapidly.

Rest the tool for a while or place the tool and battery pack separately under air ow to cool.

The LED light will ash more slowly to indicate that the battery is at low-battery capacity.

Recharge the battery pack.

BRUSHLESS

Fig. 4

BRUSHLESS

12

Fig. 5

LED Light Button

Mode Button

LED Light

Variable-Speed

Trigger Switch

14

Changing the Work Modes

• When the tool is set in forward rotation, the

work mode – a combination of rotation speed,

impact rate, and torque – can be changed to

allow a tightening force suitable to the work at

hand. Every time the mode button is pressed,

the mode will toggle between 4 work modes:

a. Low-Speed Mode - Indicator light above “1”

shines green.

b. Medium-Speed Mode - Indicator lights above

“1” and “2” shine green.

c. High-Speed Mode - Indicator lights above 1,

2, and 3 shine green.

d. Control Mode - Indicator light corresponding

to “CM” shines green.

In control mode, the tool runs at low-speed at rst to help engage the screw into work piece.

Once the screw is well engaged, the tool will increase speed automatically to nish the work

efciently with steady control over the process. The control mode is available only when the

tool is set in forward rotation (to drive screws in). If the tool is switched to reverse rotation

while in control mode, the impact force and speed are the same as the medium-speed mode

“2”.

• The modes can also be changed when the tool is set in reverse rotation to allow a loosening

force suitable to the work at hand.

NOTICE: The work mode can be changed only when any mode-indicator light is shining and

the trigger switch is not depressed. The mode button is disabled when the motor is running.

The work mode will be stored in memory and reactivated the next time the tool is turned on or

when the direction of rotation has been changed. Reset the modes as desired.

When the trigger is squeezed slightly or the mode button is pressed, any of the four indicator

lights will automatically shine green, to indicate the work mode saved during the last use and

will turn off approximately 60 seconds after the variable speed trigger switch is released. It

means that during approximately one minute after releasing the switch trigger, the work mode

can be changed.

Impact force mode

displayed

Maximum

Impact Rate

(IPM) Purpose Example of application

Low-Speed Mode 1450 Applying less torque

to avoid screw thread

breakage.

Driving small screws in

light-duty applications;

assembling furniture.

Medium-Speed

Mode 3000 Applying medium torque

and speed. Driving screws in medium

duty application.

High-Speed Mode 3600 Applying high torque

and speed. Driving heavy-duty wood

screws, tightening small

bolts.

Control Mode

(forward) 3600 Steady control of driving

screws. Driving long screws.

(specially for PH and PZ

head screw)

1

ON 10 MINS

OFF

2 3 CM

1 2 3 CM

ON 10 MINS

OFF

1 2 3 CM

ON 10 MINS

OFF

1 2 3 CM

ON 10 MINS

OFF

M

Fig. 6

Control Mode

High-speed Mode

Medium-speed Mode

Low-speed Mode

15

Removable Belt Clip (Fig. 7)

Your tool is equipped with a removable belt clip

that can be positioned on the left side of the

tool for convenient transport.

Install the belt clip onto the tool:

a. Remove the battery pack from the tool.

b. Align the rib of the belt clip with the threaded

hole on the base of the tool.

c. Insert the screw and securely tighten the

screw with a Phillips head screwdriver (not

included).

Remove the belt clip from the tool:

d. Remove the battery pack from the tool.

e. Use a Phillips head screwdriver (not included) to loosen the screw that attaches the belt clip

to the impact driver.

f. Remove the screw and the belt clip. Store them in a safe place for future use.

Bit Storage and Strap Fixing

(Fig. 8)

Your tool features an integrated bit holder on

the back of the tool base to conveniently store

a hex bit. There's also a strap xing area next

to the bit holder to attach a wrist strap.

Fig. 7

Fig. 8

Bit Sorage Area

Strap Fixing Area

16

Install and Remove Bits

Your tool is equipped with a one hand collet,

making bit installation and removal easy and

fast.

Lock the variable-speed trigger switch “OFF”

by placing the direction-of-rotation selector in

the center position.

To install the bit:

Insert the bit directly as far as it will go into the

collet. Check to make sure that the bit is rmly

in place. (Fig. 9a)

To remove the bit:

Pull the locking sleeve forward (away from

the tool), pull the bit from the collet, and then

release the sleeve. (Fig. 9b)

Fig. 9b

Locking Sleeve

NOTICE: Use only bits with power grooves; other bits can be used with a universal bit holder

that has power groove. Do not use bits that have a damaged shank.

WARNING

Wear protective gloves when removing the bit from the tool, or rst

allow the bit to cool down. The bit may be hot after prolonged use.

Fig. 9a

17

Driving Screws

Variable-speed control must be used

with caution for driving screws using bit

attachments. The best technique is to start

slowly, increase the speed as the screw

runs down, and then set the screw snugly by

slowing the tool to a stop. If this procedure is

not followed, the tool will have a tendency to

torque or twist in your hand when the screw

seats.

a. Install a suitable bit.

b. Apply just enough pressure to keep the bit

engaged on the screw.

c. Apply minimal pressure to the variable-

speed trigger switch initially. Increase the

speed only when full control can be maintained.

NOTICE:

a. Always use the correct type and size of bit for your application.

b. When turning in a screw at/near the cross cut end or an edge of wood, pre-drill a pilot hole

in order to avoid cracking of the wood.

c. When screw driving in hard wood, pre-drill a pilot hole.

WARNING

Do not over-tighten, as the force of the impact driver can break the

fastener. Keep the impact driver at a right angle to the fastener to

avoid damaging the fastener head.

Fig. 10

18

MAINTENANCE

WARNING

To avoid serious personal injury, always remove the battery pack

from the tool when cleaning or performing any maintenance.

Service

WARNING

Preventive maintenance performed by unauthorized personnel may

result in misplacing of internal wires and components which could

cause serious hazard. We recommend that all tool service be performed by a SKIL Factory

Service Center or Authorized SKIL Service Station.

General Maintenance

WARNING

When servicing, use only identical replacement parts. Use of any

other parts could create a hazard or cause product damage.

Periodically inspect the entire product for damaged, missing, or loose parts such as screws,

nuts, bolts, caps, etc. Tighten securely all fasteners and caps and do not operate this product

until all missing or damaged parts are replaced. Please contact customer service or an

authorized service center for assistance.

Cleaning

WARNING

The tool may be cleaned most effectively with compressed dry air.

Always wear safety goggles when cleaning tools with compressed

air. Ventilation openings and switch selectors must be kept clean and free of foreign matter.

Do not attempt to clean by inserting pointed objects through openings.

WARNING

Certain cleaning agents and solvents damage plastic parts. Some of

these are: gasoline, carbon tetrachloride, chlorinated cleaning solvents,

ammonia and house hold detergents that contain ammonia.

Storage

Store the tool indoors in a place that is inaccessible to children. Keep it away from corrosive

agents.

TROUBLESHOOTING

Problem Cause Remedy

Tool does not work. 1. Battery pack charge is

depleted. 1. Charge the battery pack.

2. Tool is over-loaded. 2. Turn off the tool and then try again.

3. Battery pack is too hot. 3. Turn off the tool and allow the

battery pack to cool under air ow.

4. Battery pack is not installed

properly. 4. Conrm that the battery pack is

locked and secured to the tool.

5. Burned out switch. 5. Have the switch replaced by an

Authorized SKIL Service Center or

Service Station.

LED light rapidly

flashes 1. Tool is over-loaded. 1. Release the trigger switch.

2. Tool is too hot. 2. Cool the tool under air ow.

19

LIMITED WARRANTY OF SKIL CONSUMER TOOLS

5 YEAR LIMITED WARRANTY - LEGAL

Chervon North America, Inc. ("Seller") warrants to the original purchaser only, that all SKIL

consumer TOOLS will be free from defects in material or workmanship for a period of ve

years from date of purchase, if original purchaser registers the product within 30 days from

purchase. BATTERIES AND CHARGERS are warranted for 2 years. Product registration

can be completed online at www.Registermyskil.com. Original purchasers should also retain

their receipt as proof of purchase. THE FIVE-YEAR WARRANTY PERIOD FOR TOOLS IS

CONDITIONED ON REGISTRATION OF THE PRODUCT WITHIN 30 DAYS OF PURCHASE.

If original purchasers do not register their product within 30 days of purchase, the foregoing

limited warranty will apply for a duration of three years for tools. All batteries and chargers will

remain under the two-year limited warranty.

Notwithstanding the foregoing, if a SKIL consumer tool is used for industrial, professional,

or commercial purposes, the foregoing warranty will apply for a duration of ninety days,

regardless of registration.

SELLER’S SOLE OBLIGATION AND YOUR EXCLUSIVE REMEDY under this Limited

Warranty and, to the extent permitted by law, any warranty or condition implied by law, shall

be the repair or replacement of parts, without charge, which are defective in material or

workmanship and which have not been misused, carelessly handled, or repaired by persons

other than Seller or Authorized Service Station. To make a claim under this Limited Warranty,

you must return the complete product, transportation prepaid, to any SKIL Factory Service

Center or Authorized Service Station. For Authorized SKIL Power Tool Service Stations,

please visit www.Registermyskil.com or call 1-877-SKIL-999 (1-877-754-5999).

THIS WARRANTY DOES NOT COVER ROUTINE MAINTENANCE PARTS AND

CONSUMABLES THAT CAN WEAR OUT FROM NORMAL USE WITHIN THE WARRANTY

PERIOD, INCLUDING BLADES, TRIMMER HEADS, CHAIN BARS, SAW CHAINS, BELTS,

SCRAPER BARS, AND BLOWER NOZZLES.

ANY IMPLIED WARRANTIES APPLICABLE TO A PRODUCT SHALL BE LIMITED IN

DURATION EQUAL TO THE DURATION OF THE EXPRESS WARRANTIES APPLICABLE

TO SUCH PRODUCT, AS SET FORTH IN THE FIRST PARAGRAPH ABOVE. SOME

STATES IN THE U.S., SOME CANADIAN PROVINCES DO NOT ALLOW LIMITATIONS ON

HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT

APPLY TO YOU. THIS WARRANTY DOES NOT COVER THE DAMAGE RESULTING FROM

MODIFICATION, ALTERATION, OR UNAUTHORIZED REPAIR.

IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL

DAMAGES (INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF PROFITS)

ARISING FROM THE SALE OR USE OF THIS PRODUCT. SOME STATES IN THE U.S.

AND SOME CANADIAN PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION

OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR

EXCLUSION MAY NOT APPLY TO YOU.

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO

HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE IN THE U.S., PROVINCE TO

PROVINCE IN CANADA AND FROM COUNTRY TO COUNTRY. THIS LIMITED WARRANTY

APPLIES ONLY TO PRODUCTS SOLD WITHIN THE UNITED STATES OF AMERICA,

CANADA AND THE COMMONWEALTH OF PUERTO RICO. FOR WARRANTY COVERAGE

WITHIN OTHER COUNTRIES, CONTACT YOUR LOCAL SKIL DEALER OR IMPORTER.

20

TABLE DES MATIÈRES

Avertissements de sécurité généraux relatifs aux outils électriques ....21-23

Avertissements de sécurité relatifs à la clé à chocs ..................23

Symboles ..................................................24-27

Familiarisez-vous avec votre visseuse à percussion .................28

Caractéristiques techniques .....................................28

Mode d’emploi ..............................................29-35

Entretien ......................................................36

Dépannage ....................................................37

Garantie limitée de l’outil sans l SKIL ..........................38-39

AVERTISSEMENT

• La poussière créée pendant le ponçage, le sciage, le polissage, le perçage et d’autres

activités liées à la construction peut contenir des produits chimiques reconnus par l’État

de la Californie comme étant la cause de cancer, d’anomalies congénitales et d’autres

problèmes liés aux fonctions reproductrices. Voici des exemples de ces produits chimiques :

–du plomb provenant de peintures à base de plomb;

–de la silice cristalline provenant de la brique, du ciment ou d’autres matériaux de

maçonnerie;

–de l’arsenic et du chrome provenant du bois d’œuvre traité avec un produit chimique.

• Les risques liés à l’exposition à ces produits varient selon le nombre de fois où vous

pratiquez ces activités. An de limiter votre exposition à ces produits chimiques :

–travaillez dans un endroit bien ventilé;

–munissez-vous de l’équipement de sécurité approuvé tel que des masques antipoussières

conçus spécialement pour ltrer les particules microscopiques;

–évitez l’exposition prolongée à la poussière causée par le ponçage mécanique, le sciage, le

polissage, le perçage et d’autres activités liées à la construction; Portez des vêtements de

protection et lavez à l’eau et au savon toutes les parties exposées. Les poussières pénétrant

dans votre bouche ou dans vos yeux et les poussières se déposant sur votre peau peuvent

causer l’absorption de produits chimiques dangereux.

La page est en cours de chargement...

Skil ID6744A-00 Le manuel du propriétaire

Skil ID6744A-00 Le manuel du propriétaire

dans d''autres langues

Documents connexes