Aastra DT390 Quick Reference Manual

Taper
Quick Reference Manual
Cover Page Graphic
Place the graphic directly on the page, do not care
about putting it in the text flow. Select Graphics >
Properties and make the following settings:
Width: 15,4 cm (Important!)
Height: 11,2 cm (May be smaller)
Top: 5,3 cm (Important!)
Left: -0,3 cm (Important!)
This text should then be hidden.
DT390 Cordless Phone
for MD Evolution
Quick Reference Guide
LZT 103 082 R2A
© Copyright Aastra Telecom Sweden 2009. All rights reserved.
MD Evolution – DT390
English ....................................................................................7
Español ................................................................................17
Français ...............................................................................27
Nederlands ........................................................................37
Norsk .................................................................................... 47
Svenska ...............................................................................57
MD Evolution – DT390
5
FCC Statement
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC rules.
These limits are designed to provide reasonable protec-
tion against harmful interference in a residential installa-
tion. This equipment generates, uses and can radiate ra-
dio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful in-
terference to radio communications. However, there is
no guarantee that interference will not occur in a partic-
ular installation. If this equipment does cause harmful
interference to radio or television reception, which can
be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit dif-
ferent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV techni-
cian for help.
--------------------------------------------------------------
Privacy of communications may not be ensured when
using this phone.
This equipment complies with FCC radiation exposure lim-
its set forth for an uncontrolled environment. This device
complies with FCC SAR limit of 1.6 W/kg. The highest SAR
value measured when used at the ear is 0.104 W/kg. This
device must not be colocated or operating in conjunction
with any other antenna or transmitter.
• This equipment complies with Part 68 of the FCC rules
and the requirements adopted by the ACTA. On the rear
side, underneath the battery of this equipment is a label
that contains, among other information, a product iden-
tifier in the format US:AAAEQ##TXXXX. If requested, this
number must be provided to the telephone company.
• REN is N/A as this product is intended to be connected
behind a FCC Part 68 compliant PBX system. It is not in-
tended for direct connection to telephone network.
• If this equipment cause harm to the telephone network,
the telephone company will notify you in advance that
temporary discontinuance of service may be required.
But if advance notice isn't practical, the telephone compa-
ny will notify the customer as soon as possible. Also, you
will be advised of your right to file a complaint with the
FCC if you believe it is necessary.
• The telephone company may make changes in its facil-
ities, equipment, operations or procedures that could af-
fect the operation of the equipment. If this happens, the
telephone company will provide advance notice in order
for you to make necessary modifications to maintain un-
interrupted service.
• If trouble is experienced with this equipment, for repair
or warranty information, please contact your Aastra
business partner http://www.aastra.com.
This equipment is not intended to be repaired by the
customer (user). If the equipment is causing harm to
the telephone network, the telephone company may re-
quest that you disconnect the equipment until the prob-
lem is resolved.
• Connection to party line service is subject to state tar-
iffs. Contact the state public utility commission, public
service commission or corporation commission for infor-
mation.
• If your home has specially wired alarm equipment con-
nected to the telephone line, ensure the installation of
this equipment that it does not disable your alarm
equipment. If you have questions about what will disa-
ble alarm equipment, consult your telephone company
or qualified installer.
Electrical Safety Advisory
Electrical surges, typically lightning transients, are very
destructive to customer terminal equipment connected
to AC power sources. Customer is thus recommended
to use a surge arrestor for the equipment that requires
AC power.
7MD Evolution – DT390
English
Important User Information
Copyright
© Aastra Telecom Sweden AB 2009. All rights reserved.
No parts of this publication may be reproduced, stored
in retrieval systems, or transmitted in any form or by any
means, electronic, mechanical, photocopying, recording
or otherwise, without prior written permission of the
publisher except in accordance with the following terms.
When this publication is made available on Aastra media,
Aastra gives its consent to downloading and printing
copies of the content provided in this file only for private
use and not for redistribution. No parts of this publication
may be subject to alteration, modification or commercial
use. Aastra will not be liable for any damages arising from
use of an illegal modified or altered publication.
Aastra is a registered trademark of Aastra Technologies
Limited. All other trademarks mentioned herein are the
property of their respective owners.
Warranty
AASTRA MAKES NO WARRANTY OF ANY KIND WITH
REGARD TO THIS MATERIAL, INCLUDING, BUT NOT
LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANT-
ABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Aastra shall not be liable for errors contained herein nor
for incidental or consequential damages in connection
with the furnishing, performance or use of this material.
Declaration of Conformity
Hereby, Aastra Telecom Sweden AB, SE-126 37 Hägersten,
declares that this telephone, is in conformity with the
essential requirements and other relevant pros of the
European R&TTE directive 1999/5/EC.
Details to be found at: http://www.aastra.com
Safety Instructions
Note: When using your telephone or connected
equipment, the following basic safety precautions
should always be followed to reduce risk of fire,
electrical shock and other personal injury.
Recommendations
Always keep and handle your products with care
and keep them in a clean and dust-free place.
Proper use and care will prolong the products life.
Use a soft absorbent tissue or cloth to remove dust,
dirt or moisture.
Always ensure that the phone, battery and charger
are used and operated in the environment for
which they are designed.
Operate the phone in temperatures between 0°C
to +40°C (32°F to 104°F).
Do not expose your products to liquid,
moisture, humidity, solvents, strong
sunlight, harsh environments or
extreme temperatures, never above
+60°C (+140°F), unless the product
has been specifically designed and
officially approved for such environments.
Exposure to heat may cause batteries
to leak, overheat or explode, resulting
in fire, burns or other injuries.
Do not put the product in the micro-
wave oven: This may cause damage to
either the oven or the product.
Do not attempt to disassemble or alter
any part of the phone, the charger(s)
or the battery-pack. Disassembly or
alteration may result in electrical shock
or irreversible damage to the equip-
ment.
Only a qualified service personnel
or an authorized Aastra partner should conduct
internal inspections, alterations and repairs.
Do not expose your product to open flames or lit
tobacco products.
Do not drop, throw or bend your products. This
may cause malfunction or electric shock.
Do not paint your product.
Do not use your product in an area where a
potentially explosive atmosphere exists, unless
the product has been specifically designed and
officially approved for such environments.
To avoid hearing impairment, accept the call before
holding your product (or portable handsfree device)
to your ear.
MD Evolution – DT3908
English
Disposal of the product
Your product should not be placed in
municipal waste. Please check local
regulations for disposal of electronic
products.
Power supply
Connect the AC power adapter of the charging unit
only to the designated power sources as marked on
the charger.
Make sure the AC power supply is positioned so
that it will not be subjected to damage or stress.
To reduce risk of electrical shock, unplug the
chargers from any power source before attempting
to clean or move it.
The AC power adapters must not be used outdoors
or in damp areas.
Never modify the cord or plug. If the plug will not fit
into the outlet, have a proper outlet installed by a
qualified electrician.
•Limit the distance between the mains socket and
the cordless phone when charging for easy
accessibility.
As an energy saving measure, disconnect the
charger from the main socket after charging.
When unplugging the mains adapter from the
power outlet, make sure that your hands are dry
and ensure that you hold the solid portion of the
mains adapter.
Do not pull on cables.
See the complete User Guide for available power
adapters.
Charging and batteries
Please read carefully the following
important precautions before the first
time use of the batteries. Make sure to
understand and observe all cautionary
instructions stated, so as to avoid any
possible safety hazards that are caused
by any misuse, misapplication or damage to
batteries.
Only use batteries, mains adapters or desk and rack
chargers which have been specifically designed for
use with your product.
Use of power sources not explicitly recommend-
ed may lead to overheating, reduced battery per-
formance, distortion of the equipment and fire or
other damages.
The phone is equipped with Lithium Li-polymer/
Li-Ion battery. In a complex infrastructure, the talk-
and standby time may differ, due to the con-
sequence of the increase in signaling.
The battery must always be completely charged
(minimal 4 hours) before first time use.
The battery in your product is designed to withstand
many charge cycles.
Use only the recommended charging equipment.
Improper charging can cause heat damage or even
high pressure rupture.
Observe proper charging polarity.
Do not solder lead wires directly onto the battery.
Do not allow water to come into contact with the
battery.
The battery is replaceable, however it is not the
intention to do this frequently.
Only charge the battery when placed in the phone.
Use only the specified battery-packs for your
product.
Never heat or dispose of the battery into a fire,
which, or else, may cause leakage, burst or fire.
Remove the carrying case from the product while
in charger.
Do not cover the product while being charged.
Do not charge the phone in a closed cabinet or
drawer. The charging of the battery is a chemical
process and causes the battery to become warm
during charging. Make sure the environment in
which the phone is charged, is well vented.
The cordless phone can be charged either when
switched on or off.
Do not connect the battery's positive and negative
leads altogether in any circumstances.
Do not strike or drop the battery. It may cause
damage to the battery.
Do not charge the battery below +5°C
(+41°F). Be sure to charge the battery
between +5°C and +40°C (+41°F and
104°F). Charging beyond these
conditions may impair the battery
performance and shorten the life cycle.
Do not use battery packs from different types,
brands or of different capacities.
The battery is to be stored in a dry cool place, with
the ambient temperature of approx. +25°C (+77°F)
for best performance.
The battery continues to discharge a minimal
portion of its power, even if the product is switched
off or the battery is removed.
Dispose the battery in accordance with all local
regulations, applicable in your country.
9MD Evolution – DT390
English
Warnings
Smoke or fumes
Stop operating the products and turn
off immediately in case of smoke or
fumes. Unplug the mains adapter and
remove the batteries from the phone immediately.
Continued operation may result in fire or electrical
shock.
LCD
If the liquid crystal display breaks, avoid injury by
not allowing the liquid crystal to come into contact
with eyes, skin or mouth. Prevent the liquid crystal
from leaking out of the broken glass.
Preventing malfunction
Never place the equipment in close proximity
of electric motors, welding equipment or other
devices generating strong (electro) magnetic fields.
Exposure to strong (electro) magnetic fields may
cause malfunction and corrupt the communication.
Moving the equipment rapidly between warm
and cold temperatures may cause condensation
(water droplets) to form on its internal and external
surfaces. Water droplets may cause malfunction of
the equipment and corrupt or end communication
or damage the equipment. When condensation is
noticed, stop using the equipment. Switch off the
phone, remove the battery and unplug the mains
adapter from the power outlet. Wait until the
moisture evaporates from the equipment before
putting it in operation again.
Avoid accidental drop of the phone. Use the clip,
security clip or carrying case specified for carrying
purposes of the phone.
Avoid squeezing the phone between furniture and
your body when carrying the phone in your pocket
or attached to clothing.
MD Evolution – DT39010
English
11MD Evolution – DT390
English
DT390 Cordless Phone
Quick Reference Guide
Main Display Menu
Note:
Information displayed can vary depending on version and
configuration of the exchange, or whether the phone is used in a
DECT or an IP DECT system. Consult your system administrator to
find out which type of system your phone is used in.
This Quick Reference Guide includes short descriptions
on how to use the basic features. More features and
technical requirements are available in the User Guide.
The complete User Guide is available in electronic format
on the Enterprise Telephone Toolbox CD and on
www.aastra.com (see MD Evolution platform).
Read the safety instructions before use!
1 Headset connector
2 Left soft key
3Middle soft key
4Right soft key
5 Off-hook key
6Five-way navigation key
7 On-hook and power on or off
8 Voice mail access
9 Key lock and Upper/Lower case
10 Space
11 Mute key
12 Indicator
13 Display
When you press the soft key Menu, the Messaging tab is marked
by default.
1 Contacts
2 Calls
3Settings
DT390 Cordless Phone Quick Reference Guide
MD Evolution – DT390
12
English
Switch On and Off
Switch on: Press and hold (Until display
lights up)
Ye s (confirm)
Switch off: Press and hold
Ye s (confirm)
Answer Calls
Answer: Press
Handsfree: Press
Headset: Press the answering button on the
headset.
Call pick-up: Press
13 Dial ringing extension
Austria, Italy, U.K., EBN, U.S.A, Canada:
Press
*8*; Norway: Press #13
Group call pick-up: Press
14 for primary grou
(or other defined prefix for
secondary group)
Austria, Italy, U.S.A., Canada: Press 2;
Norway: Press
#14
End call: Press
Reject call: Press
Make Calls
Dial: Dial extension number or external
line and number
Handsfree: Dial number
Common
abbreviated
number:
Dial common abbreviated
number
Dial by contact: Press Menu - Contacts - Call
contact, select contact
Note: Contacts marked with cannot be
modified.
Search and dial a
contact:
Press Menu - Contacts - Central
phonebook - Search by name
(or Search by number), enter
name (or number) and press
Search. Select contact
Dial by call list: Press select number
Redial last
external number:
11
Silent Ringing and Mute
Mute ringing
telephone:
Press to suppress the ringing.
(Press to answer.)
Switch ring
signal off: Press and hold
Mute microphone
during call: Press and hold during call
Volume
Adjust speaker
volume during a call:
Press (up and down) to adjust
volume.
Adjust ringing
volume:
Press Menu - Settings - Sound
& Alerts - Volume and adjust with
navigation keys.
Callback
(The busy number calls back when free.)
Order: Press More - Callback
If the function cannot be activated on your
phone by pressing More, press
1 instead.
Intrusion
(Intrude a busy extension to ask the party to hang up.)
Activate: Press
3
Make Calls
13
MD Evolution – DT390
DT390 Cordless Phone Quick Reference Guide
English
Park a Call
Inquiry
(The first call is parked automatically.)
Ongoing
conversation:
Press More - New call,
dial number
If the function cannot be activated on your
phone by pressing More, press soft key R
instead and dial number.
End inquiry: Press More - End call
If the function cannot be activated on your
phone by pressing More, press soft key
R,
and press
1 instead.
Refer back: Press More - Switch
If the function cannot be activated on your
phone by pressing More, press soft key
R,
and press
2 instead.
On hold
Put on hold: Press
R
Resume a call: (within 30 sec)
Conference
Ongoing
conversation:
Press More - New call,
dial number
At answer, press More -
Conference
Repeat to add more.
If the function cannot be activated on your
phone by pressing More, do the following:
Press soft key
R dial number, and press 3
at answer.
Transfer
Ongoing
conversation:
Press More - New call,
dial number
Before or after answer, press
More - Transfer
If the function cannot be activated on your
phone by pressing More, press
R, dial
number, and press
before or after
answer.
Blind transfer: Press More - Transf. to new
dial number
Call Forwarding
Internal diversion
Note: The function requires configuration by the system administrator.
Order: Press Menu - Calls - Call services -
Divert calls.
Select Internal or External, then
Activate. Enter extension number
to divert calls to, and press OK.
Cancel: Press Menu - Calls - Call services -
Divert calls. Select Deactivate and
press OK.
Follow-me
Order follow-me
from other extension
to own extension:
From own extension, press
65
Enter extension number to be
diverted, press and enter
diverted extension password.
Cancel: From own extension, press
66
Enter extension number, press
and enter diverted extension
password.
Order follow-me
from one extension
to another extension:
From own extension, press
65 *
Enter extension number to be
diverted and press
*. Enter
extension number to divert to,
press and enter password.
Cancel: From own extension, press
66
Enter extension number, press
and enter diverted extension
password.
Variable diversion
Order: Dial prefix and then diversion
number
Prefix 61: Forward all calls
Prefix
62: Forward on no reply
Prefix
63: Forward on busy
Prefix
69: Forward on no reply or busy
Cancel:
60
DT390 Cordless Phone Quick Reference Guide
MD Evolution – DT390
14
English
Forward to mini-message
Order:
* 2 Enter a mini-message code
and completing information
(if requested)
*
0 HAS CALLED YOU BACK
1
WILL CALL YOU BACK
2
WOULD LIKE TO SEE YOU
3
IN A MEETING UP TO [HH:MM]
4
ABSENT UNTIL [MM-DD]
5
IN CASE OF EMERGENCY CALL [ NNNN]
6
PLEASE CALL BACK IN A FEW MINUTES
8
BUSY - RETURN TIME [HH:MM]
9
ABSENT - RETURN DATE [MM-DD]
Note: The mini-messages above are default
messages which can be modified by the
system administrator.
Cancel:
60
Voice Mail (Optional)
New voice mail
message received:
Enter the mailbox: Press and hold
1
Note: Press and hold 1 requires that a voice
mail number has been configured to the
Voice Mail button. Please contact your
system administrator.
Contacts
Add contact: Press Menu - Contacts - Add
contact - From call list, select
a contact and press Add.
Or
Press Menu - Contacts - Add
contact - New - Add. Enter
contact details and press OK after
each detail. Press Save.
Call Forwarding
Edit contact: Press Menu - Contacts - Edit
contact. Select contact and press
Edit, edit the contact and press OK,
then Save.
Delete contact: Press Menu - Contacts - Delete
contact. Select contact and press
Delete, then Ye s to confirm.
Absence Information
Pre-defined text
Note: The function requires configuration by the system administrator.
Select absence
reason:
Press Menu - Calls - Call services.
Press Absence - Select absence
reason and enter time or date
(if requested). Press OK
Cancel: Press Menu - Calls - Call services -
Absence - Deactivate
Display Language
Change display
language:
Press Menu - Settings -
Language and select one of the
languages from the list.
Time and Date
Set time format: Press Menu - Settings - Time
& Date - Time format and select
the desired option.
Set date format: Press Menu - Settings - Time
& Date - Date format and select
the desired option.
Charging the Battery
To charge the battery, place the phone in a desk charger
or a rack charger.
Note: An orange light indicates that the phone battery is being charged.
The light turns green and is displayed to indicate that the battery is fully
charged.
Contacts
15
MD Evolution – DT390
DT390 Cordless Phone Quick Reference Guide
English
Replacing the Battery
To replace the battery, do the following:
1. Switch off the phone, open the battery
compartment, and remove the battery.
2. Disconnect the battery cable, and replace with a
new battery.
Accessories
The following accessories are available:
Also available:
Headset with microphone integrated in cable
Security string
•Rack charger
Carry case
with belt clip
Swivel clip
Headset with
microphone on boom
Standard clips Desk chargerDesk PDM charger
DT390 Cordless Phone Quick Reference Guide
MD Evolution – DT390
16
English
17MD Evolution – DT390
Español
Información importante para el usuario
Copyright
© Aastra Telecom Sweden AB 2009. Todos los derechos
reservados.
Ninguna parte de esta publicación puede reproducirse,
almacenarse en sistemas de recuperación ni transmitirse
de ninguna forma ni en ningún tipo de soporte, ya sea
electrónico, mecánico, fotocopia, grabación u otros, sin
el consentimiento previo por escrito del editor excepto
en lo dispuesto en los términos siguientes:
Cuando esta publicación esté disponible en algún
soporte de Aastra, Aastra autoriza la descarga y la
impresión de copias del contenido proporcionado
en el archivo, únicamente para uso privado y no para
posterior distribución. Está prohibida la edición, la
modificación o el uso para fines comerciales de cualquier
parte de esta publicación. Aastra no se hará responsable
de los daños que puedan surgir del uso de una publicación
modificada o alterada.
Aastra es una marca registrada de Aastra Technologies
Limited. El resto de las marcas registradas aquí mencio-
nadas son propiedad de sus respectivos propietarios.
Garantía
AASTRA NO CONCEDE GARANTÍAS DE NINGÚN TIPO EN
RELACIÓN CON ESTE MATERIAL, INCLUIDAS, AUNQUE
SIN LIMITACIÓN, LAS GARANTÍAS IMPLÍCITAS DE
COMERCIALIZACIÓN E IDONEIDAD PARA UN PROPÓSITO
DETERMINADO. Aastra no se responsabilizará de los
errores contenidos en esta publicación ni de los daños
accidentales o indirectos relacionados con la provisión,
el rendimiento o el uso de este material.
Declaración de conformidad
Por la presente, Aastra Telecom Sweden AB, SE126 37
Hägersten, declara que este teléfono cumple con los
requisitos esenciales y otras disposiciones relevantes
de la directiva europea R&TTE 1999/5/EC.
Puede encontrar más información en:
http://www.aastra.com
Instrucciones de seguridad
Nota: Al utilizar el teléfono o el equipo conectado, deben
respetarse siempre las siguientes precauciones básicas
de seguridad para reducir el riesgo de incendio,
electrocución u otros daños personales.
Recomendaciones
Utilice siempre los productos con precaución y
guárdelos en un lugar limpio y sin polvo. Un uso
y cuidado adecuados prolongarán la vida de los
productos. Utilice un paño o tejido absorbente para
eliminar el polvo, la suciedad o la humedad.
Asegúrese siempre de que el teléfono, la batería
y el cargador se utilizan y manejan en el entorno
para el que fueron diseñados.
Utilice el teléfono a temperaturas entre 0 °C y
+4C.
No exponga sus productos a líquidos,
humedad, disolventes, luz solar directa,
ambientes inadecuados o tempera-
turas extremas, nunca por encima de
60 °C, salvo que el producto haya sido
especialmente diseñado y oficialmente
certificado para este tipo de entornos.
La exposición al calor puede provocar
fugas en las baterías, así como el
sobrecalentamiento o la explosión de
éstas, lo que podría causar un incendio,
quemaduras u otras lesiones.
No introduzca el producto en un horno microondas:
podrían producirse daños en el horno o en el
producto.
No intente desmontar o modificar
ningún componente del teléfono, el
cargador o la batería. Podría producirse
una descarga eléctrica o daños irrever-
sibles en el equipo.
Las inspecciones
internas, modificaciones o reparaciones
del producto deben llevarse a cabo por parte
de personal de mantenimiento cualificado o un
representante autorizado de Aastra.
No exponga el producto a las llamas ni a productos
de tabaco encendidos.
No deje caer, arroje ni doble los productos. Podría
producirse un fallo de funcionamiento o una
descarga eléctrica.
No pinte el producto.
No utilice el producto en una zona potencialmente
explosiva, salvo que el producto haya sido especial-
mente diseñado y oficialmente certificado para
este tipo de entornos.
Para evitar la pérdida de la capacidad auditiva,
acepte la llamada antes de acercarse el producto
(o dispositivo de manos libres portátil) a la oreja.
MD Evolution – DT39018
Español
Desecho del producto
No tire el producto a un vertedero de
basura municipal. Consulte la normativa
local sobre desecho de productos
electrónicos.
Fuente de alimentación
Conecte el adaptador eléctrico de corriente alterna
(CA) de la unidad cargadora únicamente a las
tomas eléctricas especificadas en el cargador.
Asegúrese de que la fuente de alimentación de CA
se coloca de modo que no esté sometida a tensión
ni expuesta a ningún tipo de presión.
Para reducir el riesgo de descarga eléctrica,
desconecte el cargador de cualquier toma de
corriente antes de limpiarlo o moverlo.
El adaptador de CA no debe usarse al aire libre ni
en zonas húmedas.
No altere el cable ni la clavija. Si la clavija no encaja en
la toma, pida a un electricista cualificado que le
instale una toma adecuada.
Cuando cargue la batería, limite la distancia entre la
toma de corriente y el teléfono inalámbrico para
poder acceder con facilidad.
Como medida de ahorro energético, desconecte el
cargador de la fuente de alimentación principal tras
el proceso de carga.
Cuando desconecte el adaptador de la toma de
corriente, asegúrese de tener las manos secas y
de coger la parte sólida del adaptador de
alimentación.
No tire de los cables.
Consulte los adaptadores disponibles en la Guía
del usuario completa.
Carga y baterías
Lea atentamente las siguientes
precauciones importantes antes de
utilizar por primera vez las baterías.
Asegúrese de que comprende y sigue
todas las instrucciones de prevención
mencionadas para evitar posibles
riesgos para la seguridad debido a un mal uso,
un mal manejo o una avería en las baterías.
Utilice sólo baterías, adaptadores de alimentación
y cargadores de sobremesa o rack que hayan sido
especialmente diseñados para el uso con
el producto.
El uso de fuentes de alimentación que no estén
recomendadas específicamente puede provocar
un sobrecalentamiento, un mal funcionamiento de
las baterías, una alteración en el equipo y fuego u
otros daños.
El teléfono está equipado con una batería de polí-
meros de litio/iones de litio. En una infraestructura
compleja, los tiempos de conversación y espera
pueden diferir debido al incremento de la
señalización.
La batería debe estar totalmente cargada (mínimo
4 horas) antes de usarse por primera vez.
La batería del producto se ha diseñado para
soportar muchos ciclos de carga.
Utilice únicamente el equipo de carga
recomendado.
Una carga inapropiada puede producir daños por
calentamiento o incluso rotura por alta presión.
Tenga en cuenta la polaridad de carga.
No suelde hilos conductores directamente a la
batería.
•No moje la batería.
La batería es sustituible; sin embargo, no es
necesario sustituirla con frecuencia.
Cargue las baterías únicamente cuando estén
dentro del teléfono.
Utilice sólo baterías específicas para su producto.
No caliente ni tire las baterías al fuego, ya que
podrían incendiarse o producirse fugas o explosiones.
Extraiga la funda protectora del producto mientras
esté en el cargador.
No cubra el producto mientras se esté cargando.
No cargue el teléfono en un armario o cajón cerrados.
La carga de la batería es un proceso químico que
provoca que ésta se caliente. Asegúrese de que
el lugar en el que carga el teléfono esté bien
ventilado.
El teléfono inalámbrico se puede cargar tanto
encendido como apagado.
En ningún caso conecte los polos positivo y
negativo de la batería juntos.
No golpee ni deje caer la batería, ya que podría
dañarse.
No cargue la batería a temperaturas
inferiores a 5 °C. Cargue la batería a
temperaturas entre 5 °C y 40 °C. La
carga en condiciones diferentes a las
especificadas podría perjudicar el
rendimiento de la batería y reducir
su ciclo de vida.
No utilice baterías de diferentes tipos o marcas,
o de diferentes capacidades.
La batería debe guardarse en un lugar fresco y seco
con una temperatura ambiente de aprox. 25 °C para
un óptimo rendimiento.
La batería sigue descargando una parte mínima de
su energía aunque el producto esté apagado o se
haya extraído la batería.
Deseche la batería conforme a las normativas
locales aplicables en su país.
19MD Evolution – DT390
Español
Advertencias
Humo o gases
Deje de utilizar los productos y
apáguelos inmediatamente en
presencia de humo o gases.
Desconecte el adaptador de alimentación y
extraiga las baterías del teléfono inmediatamente.
El funcionamiento continuado podría provocar un
incendio o descarga eléctrica.
LCD
Si se rompe la pantalla de cristal líquido, no deje
que éste entre en contacto con los ojos, la piel o la
boca para evitar daños. Intente evitar que el cristal
líquido salga del cristal roto.
Evitar las averías
No coloque nunca el equipo cerca de motores
eléctricos, equipos de soldadura u otros disposi-
tivos que generen campos (electro)magnéticos
fuertes. La exposición a campos (electro)-
magnéticos fuertes puede ocasionar un mal
funcionamiento del producto y perjudicar la
comunicación.
Si el equipo se traslada rápidamente de una
temperatura cálida a otra fría puede ocasionarse
una condensación (gotitas de agua) en las super-
ficies internas y externas. Las gotitas de agua
pueden provocar una avería en el equipo, perjudicar
o cortar la comunicación, o dañarlo. Si percibe
condensación, deje de utilizar el equipo. Apague
el teléfono, extraiga la batería y desconecte el
adaptador de alimentación de la toma de corriente.
Espere a que se evapore la humedad del equipo
antes de volver a ponerlo en funcionamiento.
Evite que el teléfono caiga accidentalmente.
Utilice la pinza, la pinza de seguridad o la funda de
transporte indicadas para transportar el teléfono.
Evite que el teléfono quede oprimido entre otros
objetos y su cuerpo cuando lo lleve en el bolsillo
o colgado de la ropa.
MD Evolution – DT39020
Español
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70

Aastra DT390 Quick Reference Manual

Taper
Quick Reference Manual

dans d''autres langues